Search Results

Search found 5670 results on 227 pages for 'zend router'.

Page 212/227 | < Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >

  • Small TCP Window on WAN between 2 Locations

    - by Brent
    Site A: Denver datacenter. 60MBPS. Site B: Chicago. 100MBPS. ICMP pings: Packets: Sent = 176, Received = 176, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 74ms, Maximum = 94ms, Average = 75ms File transfer between sites that never goes past ~7MBPS: Windows Update download at 60MBPS+: Site to site: IPSec VPN using two Cisco 5520's. CPU at 3-4% and lots of memory to spare. The latency between to two sites is very acceptable so I can't see an issue why it is performing so slow when transferring between the two sites. I have found that any type of transfer (FTP, HTTP, Windows file shares) will never go above ~7MBPS. When the WAN was first setup, I was able to get transfers at 50-60MBPS, which is what is expected due to the WAN connection at the Site A at 60MBPS. Then a few days later, I was not able to get anything going faster than ~7MBPS. Is there a upstream router between Denver and Chicago causing this? I want to take the blame away from our setup as downloads from Windows Update go blazing fast and for the first few days after the site to site VPN came up, I was transferring VM images at 50-60MBPS. Our stack: HP P2000 MSA - HP C7000 Chassis - HP Flex-10 - Cisco Gigabit switch - Cisco ASA - WAN

    Read the article

  • Window 7 Host does not answer to ping

    - by gencha
    Today I tried printing on a shared printer on one of our homegroup members. Sadly it did not work (printer marked as offline). Shortly after, I noticed I can't even ping the machine that owns the printer (I also can not remotely access it in any other way I've tried). Currently I'm trying to ping the machine from the router both computers are connected to (and my machine in question doesn't answer). I do receive the echo requests (as verified with WireShark). I also added a rule in the Windows Firewall to specifically allow ICMP echo requests, but that didn't change anything. I also tried netsh firewall set icmpsetting 8 enable, but that didn't change anything either. Completely disabling the Windows Firewall has no effect on the issue either. One has to wonder, where does Windows log when and why it ignored any incoming packets? How can I get to the bottom of this? Here are some ways I found to dig deeper into the issue: Enabling logging on the Windows Firewall Enabling Windows Filtering Platform Auditing Both methods at least give more insight into the issue. The plain log file is full of entries like this: 2011-11-11 14:35:27 DROP ICMP 192.168.133.1 192.168.133.128 - - 84 - - - - 8 0 - RECEIVE So the ICMP packets are being dropped as if that was intended. The Event Viewer now gives a little bit more details: The Windows Filtering Platform has blocked a packet. Application Information: Process ID: 4 Application Name: System Network Information: Direction: Inbound Source Address: 192.168.133.1 Source Port: 0 Destination Address: 192.168.133.128 Destination Port: 8 Protocol: 1 Filter Information: Filter Run-Time ID: 214517 Layer Name: Receive/Accept Layer Run-Time ID: 44 This same entry is always repeated with 2 points of information changing: Process ID: 420 Application Name: \device\harddiskvolume2\windows\system32\svchost.exe The service host with the PID 420 is the host for the following services: Windows Audio DHCP Client Windows Event Log HomeGroup Provider TCP/IP NetBIOS Helper Security Center Additionally, there is currently this problem with the same machine: Even though my network is set to be a "Home network", I am unable to create a new homegroup.

    Read the article

  • Windows 7 ssh file server.

    - by Siriss
    Hello all- I have looked at the other posts, but have not quite found an answer I have a question about windows file sharing over SSH. I have copssh installed and it is working for Remote desktop connections. I have port 22 forwarded on my router etc. I connect from a Mac or Putty with this address: ssh -l copsshusername 3391:localhost:3389 [external ip] That works fine. I would like to configure Windows 7 to allow my ssh account that I use to login, access to certain shared folders. I have documents and videos and things that I would like to be able to download externally. I have done this before on Linux and a long time ago on XP, but I cannot figure out what I am missing on Windows 7. There is a designated SSH user that copssh uses to run the service and that I use to to login as. I have googled and googled and have not found a solution that does everything I need that is why I am turning here for ideas. I hope I am explaining this correctly. Thank you very much for your help!

    Read the article

  • Terminal Server in Windows Server 2003

    - by Hemal
    I have a confusion regarding what I am doing here. At present I have a Windows Server 2003 server with SP2. I have assigned RAS/VPN server role to it (through Manage my server wizard) and in my router, I setup the IP address of my RAS/VPN server as PPTP server. Staff leave their workstations ON all the time and access them from home through RDP. They first connect thorugh VPN & in the RDC they simply type their respective IP or computer name to access the office network from home. Everything works fine so far except: Staff have to leave compuers always ON in the office Speed is very slow depend how many staff members access the VPN network I was told to install and configure Terminal service to improve this situation. I already added TS Role in the server but I don't know how to clients can access the TS server from home or remote location. I really appreciate any good links or guidence from the experts in this group regarding this. Thank you in advance for any replies!

    Read the article

  • VPN messes up DNS resolution

    - by user124114
    After connecting with the Kerio VPN client (OS X Leopard) to a server, the internet (~web browsing) stopped working for the client. After poking around, the issue seems to be bad DNS server (i.e., entering IPs directly works). After disconnecting from the VPN, the invalid DNS server disappears from scutil --dns and all's well again. Now, I don't understand why OS X on the client even changes the DNS settings -- internet should be routed through a different interface, through the default gateway, not through the VPN. Questions: By what mechanism does connecting the VPN client change the "default" DNS server? How can I stop the VPN client from changing routing/DNS rules? Where is this stuff stored/modified? Before VPN: $ scutil --dns DNS configuration resolver #1 nameserver[0] : 10.66.77.1 # <---- default gateway = home router; all good order : 200000 resolver #2 domain : local options : mdns timeout : 2 order : 300000 ... VPN connected: $ scutil --dns DNS configuration resolver #1 nameserver[0] : 192.168.1.1 # <--- rubbish nameserver[1] : 192.168.2.1 order : 200000 resolver #2 domain : local options : mdns timeout : 2 order : 300000 ... The VPN doesn't appear among $ networksetup -listallnetworkservices.

    Read the article

  • 2 subnets off of 1 PC with 2 NICs

    - by Jeff
    I have a general setup I'd like to do with some IP cameras. This seems like it will work but I think I may be missing something. Our system consists of a video recorder PC connected to a switch which is connected to a number of IP cameras. I'd like to connect this system into an existing network but I want it on a different subnet. The main reason is that the cameras use a lot of bandwidth that I don't want slowing down the existing network. My idea was to install 2 NICs on the video recorder pc. 1 NIC connects to the existing network on 192.169.1.x for example, and the other NIC connect to the switch with the cameras. This NIC would be 192.168.100.x. Then we could remote to the video recorder PC with a GoToMyPC type thing for administration via the existing network. I've included a diagram of how I see this working but I'm a little fuzzy on the setup of the NICs (if this can work at all). My problem may be trying to deal with 2 subnets without a router but It really doesn't seem like it's necessary in this situation. BTW, gliffy is cool.

    Read the article

  • CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

    - by SJaguar13
    I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

    Read the article

  • Linux server: Dropped packets

    - by Lars
    I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

    Read the article

  • Ubuntu 12.04 open port 80 inside WLAN

    - by Eduard
    I have an nginx server running on ubuntu 12.04 that serves http through port 80 and https through port 443. Everything works fine if I access it from the same computer via localhost, 127.0.0.1 or the local IP 192.168.0.11. If I try to access the server from another computer in the same VLAN it does not work for http; it works for https. I have changed my nginx configuration to also listen to port 8000 for http; I can then access http from the other computer in the same VLAN via "http://192.168.0.11:8000". I also have a web server running on port 80 on a windows machine and can access it from another device in the same VLAN, therefore the router is not blocking incoming http traffic. The nginx process is run by root. I have used tcpdump and I see that packets are arriving to Ubuntu: 192.168.0.16.49735 192.168.0.11.80 and that some response is being given 192.168.0.11.80 192.168.0.16.49735 (I do not know what the response is though). There is no request arriving at the nginx web server (I have checked the access log). I have iptables empty. I have unsuccessfully tried to find a solution for a long time to this, it has now become a matter of happiness or bitterness :).

    Read the article

  • VLAN ACLs and when to go Layer 3

    - by wuckachucka
    I want to: a) segment several departments into VLANs with the hopes of restricting access between them completely (Sales never needs to talk to Support's workstations or printers and vice-versa) or b) certain IP addresses and TCP/UDP ports across VLANS -- i.e. permitting the Sales VLAN to access the CRM Web Server in the Server VLAN on port 443 only. Port-wise, I'll need a 48-port switch and another 24-port switch to go with the two existing 24-port Layer 2 switches (Linksys); I'm looking at going with D-Links or HP Procurves as Cisco is out of our price range. Question #1: From what I understand (and please correct me if I'm wrong), if the Servers (VLAN10) and Sales (VLAN20) are all on the same 48-port switch (or two stacked 24-port switches), afaik, the switch "knows" what VLANs and ports each device belongs to and will switch packets between them; I can also apply ACLs to restrict access between VLANs at this point. Is this correct? Question #2: Now lets say that Support (VLAN30) is on a different switch (one of the Linksys) switches. I'm assuming I'll need to trunk (tag) switch #2's VLANs across to switch #1, so switch #1 sees switch #2's VLAN30 (and vice-versa). Once Switch #1 can "see" VLAN30, I'm assuming I can then apply ACLs as stated in Question #1. Is this correct? Question #3: Once Switch #1 can see all the VLANs, can I achieve the seemingly "Layer 3" ACL filtering of restricting access to Server VLAN on only certain TCP/UDP ports and IP addresses (say, only permitting 3389 to the Terminal Server, 192.168.10.4/32). I say "seemingly" because some of the Layer 2 switches mention the ability to restrict ports and IP addresses through the ACLs; I (perhaps mistakenly) thought that in order to have Layer 3 ACLs (packet filtering), I'd need to have at least one Layer 3 switch acting as a core router. If my assumptions are incorrect, at which point do you need a Layer 3 switch for inter-VLAN routing vs. inter-VLAN switching? Is it generally only when you need that higher-level packet filtering ability between your departments?

    Read the article

  • Windows VPN for remote site connection drawbacks

    - by Damo
    I'm looking for some thoughts on a particular way of setting up a estate of machines. We have a requirement to install machines into unmanned, remote locations. These machines will auto login and perform tasks controlled from a central server. In order to manage patching, AV, updates etc I want these machines to be joined to a dedicated domain for this estate. Some of the locations will only have 3G connectivity (via other hardware), others will be located on customer premises in internal networks. The central server (of ours) and the Domain Controller will be on a public WAN. I see two ways of facilitating this. Install a router at each location and have a site to site VPN between the remove device and the data centre where the servers are location Have the remote machine dial up and authenticate via a Windows VPN connection to the DC via RAS Option one is more costly to setup and has a higher operational cost. It also offers better diagnostics if the remote PC goes down. Option two works well but is solely dependent on the VPN connection been made before any communication can be made to the remote machine. In a simple test, I can got a Windows 7 machine to dial a VPN prior to authentication to a domain, then automatically login to the machine using domain credentials. If the VPN connection drops, it redials. I can also create a timed task to auto connect every hour in case of other issues. I'd like to know, why (if at all) is operating a remote network of devices which are located in various out of band locations in this way a bad idea? Consider 300-400 remote machines all at different sites. I'd rather have 400 VPN connections to a 2008 server than 400 routers, however I'd like to know other opinions on this.

    Read the article

  • How to set up a easy-to-use proxy for the whole system with WinXP client and server?

    - by Pekka
    I am working together intensively with a colleague on the Canary Islands. We speak through live messenger and work together using a RDP software. She has frequent problems with connections to certain big-name and small-name sites (amongst others live.com, google.com, gmx.de) very likely to be caused by the spanish provider (the connections simply time out, this has been going on for weeks already). I have been thinking about setting up my computer as a proxy to make these connections work. I have a DSL connection and am behind a NAT capable router that I control. Does anybody know a simple, "one-click" way to transport ALL network traffic through a remote proxy? Without having to set proxy settings for each application that uses the internet? VPN is not an option, because I am behind a firewall that supports protocol 47 and such, but I have never succeeded in getting an incoming VPN connection to work. I can however redirect normal traffic using NAT. A VPN solution that does not need strange protocols would also be an option.

    Read the article

  • Remote connection to a Windows 2008 Server Web edition

    - by Lorenzo
    Hello I have just installed Windows 2008 web server to have a development/test site on my office. In the test network I only have 2 machines: Windows server 2008 Web Edition Vista x64 client machine with Visual Studio The client and the server are networked using a NETGEAR router. I have enabled Remote desktop on the server and when I try to connect to it within the Vista client I get the credential window as in the following screenshot. But even if I write the correct credentials I am not able to remote login on the server. Where am I doing wrong? Update 1 I have even tried to create a folder share on the server. But I am not able to access it for the same reason. User or password invalid it says. But this is impossible as I am logging in the server with the same credentials. Update 2 If I try to browse the network from the RDP client I receive a message saying that there are no server running Terminal Services in my network.... :O

    Read the article

  • Why does my Intel Tolapai network chip not transmit packets?

    - by Hanno Fietz
    I'm trying to deploy an embedded system (NISE 110 by Nexcom) based on the Intel EP80579 (Tolapai) chip. Tolapai apparently integrates controllers for Ethernet etc. on a single chip (Intel homepage). The machine can't get a network connection. Diagnosis as far as I could manage: Drivers drivers from Intel compiled and installed without problems (version 1.0.3-144). Kernel version and Linux distribution (CentOS 5.2, 2.6.18) match the driver's installation instructions. drivers are loaded and show up in lsmod (module names are gcu and iegbe) interfaces eth0 and eth1 show up in ifconfig ifconfig I can bring up the interfaces with fixed IP pinging the interface locally works ifconfig shows flag UP but not RUNNING Link ethtool shows "Link detected: no", "Speed: unknown (65536)" and "Duplex: unknown (255)" Link LED is on on the other side of the cable, ethtool shows "Link detected: yes" and reports a speed of 1000 Mbps, which has allegedly been auto-neogotiated with the problematic device. Network traffic analysis the device does not reply on ARP, ICMP echo or anything else (iptables is down) when trying to send ICMP or DHCP requests, they never reach the other end activity LED is off on the device, on at the other end. I tried the following without any effect: Different cables (2 straight, one crossed), I get the link LED lit up on each. Three different devices on the other end (one PC, one netbook, one router) Fixed ARP table entries on both sides Connecting both network ports of the machine with each other, won't ping through the cable, but will ping locally. Tried straight and crossed cables for that.

    Read the article

  • High latency due to non-presence of a transit provider in my country

    - by nixnotwin
    My ISP, a state owned incumbent, buys bandwidth from different transit providers. Whenever it buys transits it announces only a specific prefix (in most cases a hitherto unused) through the new transit AS. For e.g. if it runs out of bandwidth, it buys bandwidth from a new transit and announces a new prefix through it, while the same prefix is not announced (or announced with lowest metrics, so that the routes are very rarely used) via the old transits which continue to provide bandwidth to it. I am a business customer, so I have a fiber based link to the ISP and a tiny subnet is given to me. The subnet which is provide to me is part of a prefix which is announced by the AS of a transit who, it seems, do not have a presence in my country. So when I do a trace the packets, when they leave my ISP's AS, they take about 275ms to reach the transit providers core router, which is located in USA (half the world away). Also for upstream traffic my ISP uses a transit provider (tier 1) who has a presence in my country. But the return path is always through the transit which is in USA. So, average latency is 400ms. All the users of other ISPs in my country discover my subnet via USA. Even the traffic from neighboring countries, from Europe (which is much nearer) follows the path via USA. Sites using CDNs also resolve to ips in USA. I have informed the ISP NOC about the issue and I have asked them to provide an ip subnet belonging to a prefix announced by a local transit (preferably a tier 1 transit provider) and I am waiting for a reply. My question: Is it a serious issue that I must follow up to get it resolved? When I compared the latency on other providers in my country, it is, in most cases, less than half of my ISPs latency. Why my ISP doesn't announce all its prefixes to all of its transit providers, so that the packets can take efficient and nearest routes to reach prefixes that originate within its network?

    Read the article

  • Unable to connect to FTP - Connection timeout after MLSD

    - by Afrosimon
    So here is my problem, I'm absolutely unable to connect to a FTP server, in circumstances I've never seen before. Here is the situation : I get a "Connection timed out" just after the MLSD command. I usually use Filezilla, under Ubuntu, but to make sure the problem isn't related to this particular client I tried a few others : gftp on ubuntu and winscp and freeftp on windows 7. All the same result. Also made sure to try with Active or Passive modes. Same result. At this point I would be inclined to think there is something wrong with my current network (furthermore, according to a coworker the FTP server is OK). But I did check with http://ftptest.net/ and I am able to get the directory listing (which I'm not able to through a FTP client). So in the end the last thing I didn't tried is to go on another network, solution which seems would work, but wouldn't be very practical in the long run. And thus I guess there's something wrong with my router... but what could it possibly be? Note : I did try to register and post this question on filezilla's board first... but I can't create an account with a gmail nor hotmail account. WTF?

    Read the article

  • OpenVZ with bridged interfaces and VLAN

    - by Deimosfr
    Hi, I've got a problem with OpenVZ with bridged VLAN. Here is my configuration: +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN work on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110: inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seems to be working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian Lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks OK, but when I start my VE, here is the message: ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please? Thanks

    Read the article

  • Virtualizing an Inline network appliance with VirtualBox (or VMWare)

    - by Tzury Bar Yochay
    My device, which is a Linux based IP in-liner is transparent to the network peripherals, that is, no IP address assigned to any of its interfaces. For the sake of the conversation, let's use ADSL connection as an example, while the device is inspecting the bi-directional traffic, the network is behaving same as if device was not there, attached to the wire (see Physical setup at the attached diagram). I wonder if I can enclosed that "device" within a Windows machine and have it operated virtually so it still seats inline between the ADSL router and the Windows netwroking interface by using virtual NICs, (or whatever their name is in windows), and inspecting the traffic, same as if it was on a separate physical device, the drawing under "Virtual Setup" in the attached diagram show what I am trying to achieve. Reading a bit on the VirtualBox docs, seems like binding the right side is relatively simple, perhaps I should have one network adapter set as Bridge Networking and VirtualBox will connect it to the physical NIC on the host machine, and network packets are exchanged directly, circumventing the host operating system's network stack (WinXP in my case). However, I have no idea how to achieve the left side of my diagram, which requires adding virtual NICs to windows and configure them correctly in a way to make that pipeline possible. I would appreciate any help. by the way, if that is not possible with VirtualBox but with other virtualization solution (e.g. VMWare), I would accept the other as well.

    Read the article

  • ubuntu 9.04 pptp broken after a power failure

    - by kevin42
    I have a small Ubuntu 9.04 router setup as a NAT box and a PPTP server. After a power failure everything except the PPTP server still works. A windows client gets to "registering your computer on the network" but then says Error 742: The remote computer does not support the required data encryption type. I did some research and I think the problem is with the ppp_mppe module. When I try to run 'modprobe ppp_mppe' it hangs indefinitely. What would cause this hang? Any ideas how I can troubleshoot this further? Thanks for the help! UPDATE: I am still having the problem, however I have found some more information. When the first user tries to connect to pptp, the process list shows modprobe sha1 running, and one instance of modprobe ppp_mppe for each connection attempt. If I killall modprobe at this point the next connection attempt works, and everything is fine until the next reboot. I'm planning to do a clean install at some point in the future but I'd really like to get to the real cause of this.

    Read the article

  • Netflix streaming stops loading at 98% on Revo 3700

    - by Martin Harris
    I'm trying to stream Netflix on an Acer Revo 3700 running Windows 7 Home Premium, but it hangs on the loading screen at 98% (after it has formatted the player to the right aspect ratio and added the controls, but before the video starts) with no error messages or failures. I have two other machines on the same network, one running Windows 7 Home Premium and another running XP, which both stream faultlessly. Things I have tried: Both a wired and wireless connection to the router Upgrading the video and audio drivers IE, Chrome and Firefox Boxee software Connecting with a VGA cable instead of HDMI (in case it is a HDCP thing) Uninstalling and reinstalling Silverlight. Getting someway into loading a HD movie and turning "Allow HD" off Does anyone know what Netflix is doing at the 98% load mark? Are there any log files? Anything else worth trying? Full disclosure: I'm using Netflix from the UK through a US based VPN. I've tried multiple VPNs and the problem is exactly the same, also the other machines on the same network through the same VPN work fine so I don't think this is the issue, but it might be a factor. The region check happens at around 7% and I get past that.

    Read the article

  • Linux wireless disconnect every 20 minutes

    - by james
    My laptop uses CentOS 6.3 with kernel 2.6.32-279.el6.x86_64. My wireless adaptor is Intel Corporation Centrino Wireless-N 1000. My wireless connection always get off after about 20 minutes. The network applet shows the connection is still on with good signal strength, but I just cannot load any web pages even the configuration page of the wireless router. The problem will continue until I disable and reconnect the wireless. Other devices like my cell phone uses the same wireless network without the problem. Even yesterday I'm using the same laptop with Fedora 17 without this problem. I also searched the internet and someone said running services NetworkManager and network simultaneously may be a problem. But I cannot stop any one of them because: if I stop network and start NetworkManager, the network service will start automatically; if I stop NetworkManager and run network, it says "Device does not seem to be present, delaying initialization." when trying to bringing on the wireless. What shall I do to get rid of the problem? Thank you very much!

    Read the article

  • Apache and Virtual Hosts Problem on OS X

    - by Charles Chadwick
    I recently formatted and installed my iMac. I am running 10.6.5. Prior to this format, I had the default Apache web server up and running with several virtual hosts, and everything ran beautifully. After formatting, I set everything back up again, and now Apache is acting funny. Here is a description of what I have going on. My default root directory for the Apache Web server is pointed to an external hard drive. In my httpd.conf, here is what I have: DocumentRoot "/Storage/Sites" Then a few lines beneath that: <Directory /> Options FollowSymLinks AllowOverride All Order deny,allow Allow from all </Directory> And then beneath that: <Directory "/Storage/Sites"> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny Allow from All </Directory> At the end of this file, I have commented out the user dir include conf file: Include /private/etc/apache2/extra/httpd-userdir.conf And uncommented the virtual hosts conf file: Include /private/etc/apache2/extra/httpd-vhosts.conf Moving on, I have the following entry in my vhosts file: <VirtualHost *:80> DocumentRoot "/Storage/Sites/mysite" ServerName mysite.dev </VirtualHost> I also have a host record in my /etc/hosts file that points mysite.dev to 127.0.0.1 (I also tried using my router IP, 192.168.1.2). The problem I am coming across is, despite having PHP files in /Storage/Sites/mysite, the server is still looking at /Storage/Sites. I know this because in the DocumentRoot contains a php file with phpinfo() (whereas the index.php file in mysite has different code). I have tried setting up other virtual hosts, but they are still doing the same thing. Also, "NameVirtualHost *:80" is in my vhosts file. I saw as a solution on another thread here. Doesn't seem to make a difference. Any ideas on this? Let me know if this is not enough information.

    Read the article

  • Synchronising a remote folder with a local one.

    - by Workshop Alex
    I am using a network disk (that's connected to my router by USB) to store several data files. A simple .NET application that I've created is supposed to read and modify these data files. However, some security issues are preventing this application to access these files directly. (Actually, these have been built-in to my application on purpose since it's not going to support NAS disks.) Since this disk is shared with several computers, I just want to have a simple synchronisation method, which will copy the files to a local folder where3 my application can access them. And, once modified, it should send back the modified files to the NAS disk again. I have two options: 1) Build a second application to do my own synchronisation. 2) Find some build-in function inside Windows 7 Ultimate which can do this for me. Option 2 is preferred. Option 1 is something I can do easily, if need be. I don't need third-party tools. (Still, feel free to add some references to good tools, although I won't accept them as answers.) Basically, is this possible with Windows 7 and if so, how?

    Read the article

  • XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

    - by ewall
    Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

    Read the article

  • Internet Problem: Wireless connected but no connection to internet

    - by Josh K
    Hey i have a interesting network setup on a laptop here and for some reason the internet isnt working. I am connected to a secure network via wireless router and taskbar says i am connected and with good signal strength but in my internet browser i cant connect to any websites, the error is: This webpage is not available. (Chrome) I am using Chrome, but websites dont work on IE either. Heres a little background on the setup i have. I have a Ethernet connected to the laptop with a static ip, and then i have the wireless setup with DHCP enabled. I am using the ethernet to connect to the network (for remote desktop) but the wireless for internet (to avoid the network firewalls). this set up has worked fine for a few months, but i cant figure out what is going on now. Might be worth it to note it is a Lenovo Thinkpad and i just uninstalled ThinkVantage Access Connections (as it was giving me ample problems prior to this one, which i consider a step up) Tried repairing connection as well, let me know if you guys have any ideas please! EDIT: Solved-Dead Modem in the server room.... Sorry guys didn't have access to that myself

    Read the article

< Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >