Search Results

Search found 7697 results on 308 pages for 'eb dev'.

Page 220/308 | < Previous Page | 216 217 218 219 220 221 222 223 224 225 226 227  | Next Page >

• Dual boot on Hp Envy Ultrabook

  - by phodu_insaan

  I just bought a HP Envy ultrabook 1002TX. It comes with a Win7 Home basic and a 32GB SSD + 500GB HDD. I started to install ubuntu and in doing so went and deleted all the partitions on my HDD and recreated them the way I wanted. Then when I tried to install ubuntu it didn't recognize my HDD. To solve this i typed dmraid -E -r /dev/sdX where the 'X' was my SSD drive. After this ubuntu can install but windows for some reason does not install. Also the Intel Caching feature is lost and SSD is just sitting and doing nothing. I want to know how to solve this problem. Ideeally I would like to use the SSD for caching, either in windows or ubuntu. How do I get the SSD back to working as an Intel rapid cache? How do I get windows to install properly? It tell me that windows is unable to configure itself to my hardware, and my PC came with windows pre-installed so this is not possible. Sorry for the long question and thanks for your answers! PS: At one time when I booted I pressed Ctrl+i and went to the intel rapid cache menu. I think i screwed up something in here, because only after this the rapid cache stopped working, and each time I booted the PC thought the BIOS was my primary disk.

  Read the article

• Windows Physical Direct Memory Mapping

  - by chrisjleaf

  I'm a bit disappointed there is almost no discussion of this no matter where I look so I guess I'll have to ask. I'm writing a cross platform memory bench marking application which requires direct physical address mapping rather than virtual addressing. EDIT The solution would look something like the Linux/Unix system calls: int fd = open("/dev/mem", O_RDONLY); mmap(NULL, len, PROT_READ, MAP_SHARED, fd, PHYSICAL_ADDRESS_OFFSET); which will require the kernel to either give you a virtual page mapping to the desired physical address or return that it failed. This does require supervisor privileges but that is ok. I have seen a lot of information about shared memory and memory mapped files but all of these reside on disc and are thus not really useful when I'm trying to make a system dependent read. It is very similar to writing an IO driver although I do no need write permissions to the physical address. This site gives an example of how to do it on a driver level using the Windows Driver Kit: NT Insider: Sharing Memory between drivers and applications This solution would probably require Visual Studio which currently I do not have access to. (I have downloaded the WDK api but it complained about my use of GCC for Windows). I'm traditionally a Linux programmer so I'm hoping there might be something really simple I'm missing. Thanks in advance if you know something I don't!

  Read the article

• My 2012 Professional Development Goals

  - by kerry

  Once again I am going to declare some professional goals for my upcoming year. Convert my blog to Jekyll hosted on github – I am tired of wordpress, tired of spam, and would like to try something new.  I have already started on this.  Just need to finish it up. Launch my GWT / Google App Engine application – I am currently developing a GWT application to be deployed to Google App Engine. Do another presentation at the user group – At least a few lightning talks.  I have a few ideas. Attend a tech conference – Dev Nexus is the likely target Post more often – I did 10 posts last year, would like to maybe double that next year (including this one) Attend a user group meeting outside of Nashville JUG – A rollover from last year, I will probably be regularly attend the Interactive Developers meeting Study another language – I have been thinking about looking in to Dart or perhaps Go Launch an Android app – Another holdover from last year I am thinking of doing a small app having to do with managing the silent state of the phone

  Read the article

• Couldn't pass the signin screen on ubuntu

  - by Amokrane

  I have an issue here with my computer using ubuntu 10.10 on a 64 bits machine. When I start it, I have the login screen, I enter my credentials but instead of starting the session it reloads the login screen again. I checked the disc using fsck and it seems clean. How should I proceed to diagnose and repair this issue? Thanks! [Edit] I went to the log files, this is what I got: auth.log pam_unix (gdm:session): session opened for user amokrane by (uid=0) pam_ck_connector (gdm:session): nox11 mode, ignoring PAM_TTY :0 pam_unix (gdm:session) :session closed for user amokrane messages.log No ACPI video bus found I also took a shot with my camera of the black screen that appears between the two login screens, it says something like: fsck from util-linux-ng 2.17.2 /dev/sdc4 : propre, xxxx files, xxxx blocs Starting AppArmor profiles Skipping profiles in /etc/apparmor.d/disable: usr.bin.firefox Setting sensors limits Starting postgreSQL ... /var/log/Xorg.0.log [ 25.375] (II) intel(0): Modeline "1920x1080"x60.0 172.80 ... [ 28.850] (II) Power Button: Close [ 28.850] (II) UnloadModule: "evdev" [ 29.910] (II) Power Button: Close [ 28.910] (II) UnloadModule: "evdev" [ 28.941] (II) AT Translated Set 2 keyboard: Close [ 29.000] (II) ImPS/2 Generic Wheel Mouse: Close [ 29.000] (II) UnloadModule: "evdev" [ 29.039] ddxSigGiveUp: Closing log Update I tried the following: Ctrl-Alt-F1 on the login screen (to runt the console). sudo pkill startx sudo rm /tmp/.X0-locl startx But it tells me that the x server is already running.

  Read the article

• ArchBeat Link-o-Rama for October 23, 2013

  - by OTN ArchBeat

  Virtual Dev Day: Oracle ADF Development - Web, Mobile, and Beyond This free virtual event includes technical sessions that range from introductory to deep dive, covering Oracle ADF and Oracle ADF Mobile. Multiple tracks cover every interest and every level and include live online Q&A for answers to your technical questions. Register now! Americas: Tuesday, November 19, 9am-1pm PT / 12pm-4pm ET / 1pm-5pm BRT APAC: Thursday, November 21, 10am–1:30pm IST (India) / 12:30pm–4pm SGT (Singapore) / 3:30pm–7pm AESDT EMEA: Tuesday, November 26, 9am-1pm GMT / 1pm-5pm GST/ 2:30pm-6:30pm IST A Roadmap for SOA Development and Delivery | Mark Nelson Do you know the way to S-O-A? Mark Nelson does. His latest blog post, part of an ongoing series, will help to keep you from getting lost along the way. Updated ODI Statement of Direction | Robert Schweighardt Heads up Oracle Data Integrator fans! A new product statement of direction document is available, offering "an overview of the strategic product plans for Oracle’s data integration products for bulk data movement and transformation, specifically Oracle Data Integrator (ODI) and Oracle Warehouse Builder (OWB)." Java-Powered Robot Named NAO Wows Crowds | Tori Wieldt Java community manager Tori Wieldt interviews a robot and human. Nordic OTN Tour 2013 | Lonneke Dikmans Oracle ACE Director Lonneke Dikmans checks in from the Stockholm leg of the Nordic OTN Tour for 2013, sponsored by the Danish Oracle User Group and featuring fellow ACE Directors Tim Hall and Sten Vesterli, plus local speakers at various stops. Lonneke's post include the slides from three of the presentations. Thought for the Day "Some people approach every problem with an open mouth." — Adlai E. Stevenson23rd Vice President of the United States (October 23, 1835 – June 14, 1914) Source: brainyquote.com

  Read the article

• Ubuntu update deleted entries from grub

  - by Kevin

  My computer currently has Fedora, Ubuntu, and Windows installed. I just updated Ubuntu 12.04, and on restarting, the Fedora entry was gone from GRUB. Ubuntu and Windows remained, though. I have looked at these threads: Fedora login gone after Ubuntu updates on a dual boot http://forums.fedoraforum.org/showthread.php?t=279221 GRUB's menu.lst deleted after a kernel update However, I cannot figure out how to mount the drive as suggested. It does not appear in the list on the left side of nautilus as shown in the links above. I also tried running the following as suggested above: sudo grub-install /dev/sdX sudo update-grub But this gave scary errors: /usr/sbin/grub-setup: warn: Attempting to install GRUB to a partitionless disk or to a partition. This is a BAD idea.. /usr/sbin/grub-setup: warn: Embedding is not possible. GRUB can only be installed in this setup by using blocklists. However, blocklists are UNRELIABLE and their use is discouraged.. /usr/sbin/grub-setup: error: will not proceed with blocklists. The highlighted drive below is where Fedora lives. Thanks for any help reversing Ubuntu's decision to delete this from GRUB.

  Read the article

• Ethernet Connection Unavailable

  - by fabikw

  I'm running Ubuntu Server 12.04 on a laptop with an Intel NIC (driver e1000e). When I connect the ethernet port to the internet (college network, DHCP) it works out of the box. Now I'm trying to connect it to a networked USRP (if you want to know what it is). A friend of mine managed to do this in his laptop (running regular Ubuntu 12.04) just by setting up a new Wired connection in the Network Manager with appropriate addresses. However, when I do the same, no wired connections are available. The output of nmcli -p dev is =========================================== Status of devices =========================================== DEVICE TYPE STATE ------------------------------------------- wlan0 802-11-wireless connected eth0 802-3-ethernet unavailable but the cable is connected to the device and the device is powered up. Any idea how to solve this? UPDATE: After stopping the network-manager service, setting up the connection manually and starting the service again, it now detects the ethernet connection. However, the device still can't receive data and doesn't answer to pings. UPDATE 2: As suggested I tried using a cross over cable but the result is exactly the same. However, I found out that connecting the device to the dock (as opposed to directly to the laptop) works fine. I know that the ethernet port in the laptop works fine, because connecting to the network through it works. Is it possible that the port in the laptop doesn't support Gb Ethernet (because that's what the device requires) but the one in the dock does?

  Read the article

• How to fix the “Live INT automatically logs out”

  - by ybbest

  Problem: Live INT environment automatically logs out I am trying to setup the Authentication with Windows Live ID and followed this blog post ; I have a problem logging in to live INT web site. Whenever I try to log in (https://login.live-int.com/login.srf  this is the internal Live environment to be used in a dev. environment.), after entering valid email/password I get redirected to the logout page. I tried 2 different accounts (one with existing email address, and other one with newly created @hotmail-int.com address) and 3 different browsers so I’m sure that neither account nor the browser are the cause of this. I also tried to enter wrong password, and in that case I get the message that the password is wrong. Solution: All you need is the unique ID in order to add the user to SharePoint , you can get the ID without logging into the Live INT environment. I think the Live internal environment is not working correctly for some reasons , the reason I need to login to the Live internal environment is that I need to get the unique ID for the test account so that I can add the user to SharePoint. All the blogs I have come across require you to login in order to get the unique ID. However, I figured out another way of getting the unique ID without logging in. Steps are below: Register a new test account in the Live internal environment. Go to the SharePoint site collection that has  Live ID authentication enabled and select the LiveID INT(it will be different as you could name it differently when you set up the authentication provider) from the dropdown. Try login using the Internal Live account, you will get an Access Denied Error as below showing your  unique ID for the test account. Add that account to your SharePoint Group, boom, it works. I hope it will help anyone who needs to do this stuff in the future.

  Read the article

• Pandaboard crash on startup or freeze after minutes

  - by Meach

  I just received my Pandaboard ES (rev B) and I am having trouble after installing ubuntu-omap4-addons. Once I copied the image ubuntu-12.04-preinstalled-desktop-armhf+omap4.img on my sd card and boot the pandaboard with it, I run the following commands: sudo add-apt-repository ppa:tiomap-dev/release sudo apt-get update sudo apt-get dist-upgrade sudo apt-get install ubuntu-omap4-extras At the end of the installation of ubuntu-omap4-extras, Ubuntu tells me that a problem occurs when the console displays: ldconfig deferred processing now taking place Clicking on "report the problem" tell me that the problem concerns pvr-omap4-dkms. I read somewhere that this can happen and it is better to reinstall pvr-omap4-dkms. Which I am doing by running: sudo apt-get install --reinstall pvr-omap4-dkms I reboot. Then the board has sometimes difficulties to start Ubuntu: it freezes during the loading page, only action I can do is unplugging the board to start it again. Some other times, Ubuntu load successfully but then freeze at another random time, in the range 20 - 40 minutes. I searched on internet for similar bug and found this: https://bugs.launchpad.net/ubuntu/+source/linux-ti-omap4/+bug/971091 So I typed this in: update-rc.d ondemand disable apt-get -y install cpufrequtils echo 'ENABLE="true" GOVERNOR="performance" MAX_SPEED="0" MIN_SPEED="0"' > /etc/default/cpufrequtils cpufreq-set -r -g performance reboot But it doesn't seems to fix the bug. Another detail: on startup, before the loading screen of Ubuntu (when there is the two penguins displayed :)), it shows this: [0.297271] CPU1: Unknown IPI message 0x1 [0.308990] omap_hwmod: mcpdm: _wait_target_ready error: -16 [0.354705] omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts [0.354766] omap_hwmod_mux_init: Could not allocate device mux entry [2.107086] thermal_get_slope:Getting slope is not supported for domain gpu [2.107116] thermal_get_offset:Getting offset is not supported for domain gpu [2.107299] stm_fw: vendor driver stm_ti1.0 registered [8.725555] OMAPRPC: Registration of OMAPRPC rpmsg service returned 0! debug=0 Any idea what can be wrong? I am not that good with Ubuntu so any help will be appreciated. Cheers! Meach

  Read the article

• Xorg crashes ever since using Nvidia dual monitors

  - by legion

  Well ever since I have used dual monitors with the NVIDIA X Server Settings program my xorg process has been crashing after a while, and its generally a pretty long while of like 6 hours afterwards. Before NVIDIA changed my xorg.conf file I only had xorg crash like twice in 2 months, I can't figure out what is going on. I am running ubuntu 12.04 with the MATE desktop environment v 1.2.0 xorg.conf # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 295.33 (buildd@allspice) Fri Mar 30 15:25:24 UTC 2012 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "LEN" HorizSync 51.8 - 55.8 VertRefresh 40.0 - 60.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "NVS 3100M" EndSection Section "Screen" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0" # Removed Option "TwinView" "1" # Removed Option "metamodes" "DFP-1: nvidia-auto-select +0+0, CRT: nvidia-auto-select +1920+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinViewXineramaInfoOrder" "DFP-1" Option "TwinView" "0" Option "metamodes" "DFP-0: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection

  Read the article

• USB mouse pointer only moving horizontally on macbook 6.2 with 12.04

  - by Glyn Normington

  After installing Ubuntu 12.04 on a macbook pro 6.2, the touchpad and external USB mouse worked perfectly. After rebooting I can't get either touchpad or external USB mouse to work. Sometimes no mouse pointer is visible, but more often I can only move the mouse pointer horizontally five sixths of the way across the display (from the top left). I have uninstalled mouseemu. xinput list shows the USB mouse. xinput query-state for the USB mouse shows the following: ButtonClass button[1]=up ... button[16]=up ValuatorClass Mode=Relative Proximity=In valuator[0]=480 valuator[1]=2400 valuator[2]=0 valuator[3]=3 and re-issuing this command with the pointer at its right hand extreme displays the same except for: valuator[0]=1679 So the valuator[0] seems to be the x-coordinate of the pointer and the range of motion 480-1679 is indeed about five sixths of the display width (1440). valuator[1] is suspiciously large given the display height is 900. Perhaps this is a side-effect of having previously been using a dual monitor (although booting with that monitor connected does not help). There are other entries listed under xinput list: Virtual core XTEST pointer which seems stuck at position (840,1050). bcm5974 which seems stuck at position (837,6700). Removing the bcm5974 module using rmmod disables the toucpad as expected but does not fix the USB mouse problem. After adding the module back, it is stuck at position (840,1050) instead of (837,6700). /etc/X11/xorg.conf was generated by nvidia-settings and contains: Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "ZAxisMapping" "4 5" although I don't know how plausible these settings are. Any suggestions?

  Read the article

• Offshoring: does it ever work?

  - by DanSingerman

  I know there has been a fair amount of discussion on here about outsourcing/offshoring, and the general opinion seems to be that at best it is difficult, and at worst it fails. I have direct experience of offshoring myself; a previous company where I was a dev manager wanted to send some development offshore, and we ran a pilot scheme to see how well it would work. Of course it was a complete failure, although it is not completely clear to me whether this was down to the offshore devs being less talented, the process, or other factors (no doubt it was really a combination). I can see as a business how offshoring looks attractive (much lower day rate), but as far as I can see, the only way it could possibly work is if you do exceptionally detailed design up front, with incredibly detailed specifications; and by the time you have invested in producing that, you have probably spent as nearly as much as if you had written the actual code locally (which I think is an instance of No Silver Bullet) So, what I want to know is, does anyone here have any experience of offshoring actually working ever? Especially if there are any success stories of it working in a semi-agile way? I know there are developers here from all over the World; has anyone worked on an offshore project they consider successful?

  Read the article

• Problems syncing photos and strange effects of uploaded files from other devices

  - by Daniel

  I have a Galaxy Spica (GT-i5700) Android v2.1, rooted with Leshak dev 7 #123. But never mind the root info, the problem would be the same unrooted. The photos from this phone is stored in "sdcard/images", nevertheless the phone also creates a "sdcard/DCIM" but only stores some thumbnails there. Problem nr 1: U1 only reads the DCIM-folder for automatic photo-upload. So photos stored in this phone is not uploaded. If I move photos to "DCIM" folder, U1 recognises the photos and start uploading them. Possible solution: Could there be an option in the settings, to set preferred photo folder? Problem nr 2: Out of 74 pictures, 12 did not get uploaded. Pressing "Retry failed transfers" in Settings does nothing. Pressing the files where status is "Upload failed, tap to retry" only changes the status to "Uploading..." but nothing gets uploaded. If I upload another file to U1, it is uploaded directly without any problem. It has nothing to do with file size, 1,1 MB files has been uploaded fine whilst some failed are 0,8 MB. Problem nr 3: The photos from DCIM are in my case uploaded to a folder called "Pictures - GT-I5700" in U1. If I log in to the homepage and from there upload another photo in "Pictures - GT-I5700", it shows up in U1 on my phone fine. But when I tap it, U1 downloads the photo to "sdcard/U1/Pictures - GT-I5700". If it sync photos from "sdcard/DCIM" to a specific folder, why not also download files to the same folder from which it is synced? After a while of usage, syncing and uploading files from different clients it would be a mishmash of folders and places files are stored and considering that I see no use of U1 at all. Another question: If my SD card in some way breaks down/some folders cannot be read/card temporarly changed and U1 is running, does U1 consider that as files deleted and also delete from the cloud?

  Read the article

• Installation causing broken packages

  - by AWE

  Here I come I am so determined to use Ubuntu that I paid a professional to install it for me (dualboot). When I got it I got a lot of things from the software center. Skype did not have a download button so I googled it and Ubuntu help told me to do this: sudo add-apt-repository "deb http://archive.canonical.com/ $(lsb_release -sc) partner" and then this: sudo apt-get update && sudo apt-get install skype The terminal told me "that this is potentially harmful..." but I thought it was Ubuntu language meaning "are you sure?" Now items cannot be installed or removed until the package catalog is repaired, so I want to repair it but the package operation fails. "sudo aptitude -f install" - command not found Synaptic package manager tells me that I have two broken packages, libc6 and libc6-dev but doesn't help, only makes life complicated. What the *#$%&!!! I don't want to be forced to become a computer scientist just to be able to use a free source os. P.s. the sound stopped working

  Read the article

• FOSS Development: Who develops the OS-specific packages?

  - by achristi

  I have a couple of FOSS projects. They can be a bit of a pain to get running unless you've got dependencies in place already, which I figure is par for the course for FOSS projects. We know that each free operating system out there has its own package management systems. A few of them, such as homebrew on Mac OS or AUR on Arch linux are very friendly to community contributions. What I am wondering is, who exactly is expected to contribute packages? Primarily I am concerned with the case of small or developing projects, since it's pretty standard for the big projects to be put in there by the OS maintainers. From my perspective, it is something of a chicken-egg problem, because your software will not make its way into a package system if it does not have users, and it is less likely to gain users if it is not easy to install and use. For the sake of discussion, let's assume that the software in question is actually legitimately useful. I can see where people could create crapware or spam and that should obviously be kept out of any package system. So, in summary, whose job is this? Is it spammy for a FOSS software dev to put his own work into various OS package repositories?

  Read the article

• alsa - sound issues on ubuntu 12.04

  - by tam_ubuuser

  i am having an sony E series laptop.i have an HDMI port .at this stage ,i have tested my sound card , which provides audio out on my laptop i.e i could hear songs .my laptop has two sound cards amd 5450 and an intel-hda(alsamixer shows that as s/pdif) . i decided to connect HDMI output to my new HD-TV.but, i could get only visuals on my TV,NO AUDIO OUTPUT ( HDMI cable works fine with win 7).my laptop has two sound cards.but i couldn't switch output to other card.( i don't know ,how to do that) i decided to update alsa. complied the following code in terminal. sudo apt-add-repository ppa:ubuntu-audio-dev/alsa-daily sudo apt-get update sudo apt-get install alsa-hda-dkms then,strangely no login sound, and no audio output on my laptop at all .then, started complied code from step1 sound troubleshooting procedure from offical ubuntu site.then, my speaker icon taskbar disappeared .obivously $aplay -l ,provided output as no soundcards detected . so , i implemented step 4 from that guide, it provides a output of all hardware devices in my laptop. *-multimedia UNCLAIMED description: Audio device product: Cedar HDMI Audio [Radeon HD 5400/6300 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: latency=0 resources: memory:f0040000-f0043fff *-multimedia UNCLAIMED description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f5e00000-f5e03fff that command displayed output name of the two cards . but , still i have no positive output on $aplay -l. so therfore, i think alsa couldn't detect my sound cards . is there solution to this problem? it could be better,if alsa would channel output from multiple sound cards ? how should install and configure alsa such that detects HDMI cable as soon i connect to my HD tv? is it possible to alsa and pluseaudio 2.0 to co-exist, if so how?

  Read the article

• My game seems to be incompatible with recording software. What could be causing this?

  - by Lewis Wakeford

  I've just finished a little Game-Dev project for university and I need to record a video to accompany my submission (just in case they can't get my source to work). Basically my game doesn't work at all when FRAPS or Bandicam attempts to attach to it, I get a black screen and a stream of GL INVALID OPERATION messages from my error reporting code. Dxtory can't seem to hook into it correctly at all, it doesn't display it's FPS counter or anything. My game logic appears to be running correctly from the debug traces, it just seems like all the gl library calls break. I don't know a huge amount about how these programs operate so I don't really know what I could be doing to cause this. I've heard they read from the OpenGL frame buffers so maybe I'm doing something wrong there? I'm letting GLFW and GLEW do all the low level initialization, but I have successfully recorded projects with the same setup and recording software. Essentially, has anyone ever run into something like this before or do you know anything about how these programs work that could give a clue as to the cause of the issue?

  Read the article

• USB flash module giving errors

  - by vshenoy

  Hi, I have a SATA USB flash module which was earlier running a 2.4 linux kernel (2.4.36.6) and on which now I am trying to install ubuntu server 10.04.1 LTS. I have two such USB flash modules and on one of them the installation process itself giving these errors: sd 4:0:0:0 [sda] Device not ready sd 4:0:0:0 [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sd 4:0:0:0 [sda] Sense Key : Not Ready [current] sd 4:0:0:0 [sda] Add. Sense: Medium not present sd 4:0:0:0 [sda] CDB: Write(10): 2a 00 00 05 48 02 00 00 04 00 end_request: I/O error, dev sda, sector 46114 usb 1-1: reset high speed USB device using ehci_hcd and address 2 Buffer I/O error on device sda1, logical block 172033 lost page write due to I/O error on sda1 Buffer I/O error on device sda1, logical block 172034 lost page write due to I/O error on sda1 on the other the installation is successful, but after a day or two of running the machine hangs because of kernel spewing these messages: Remounting filesystem read-only EXT2-fs error (device sda1): read_block_bitmap: Cannot read block [bitmap - block_group = 105, block_bitmap = 860161] EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=13083, block=24683 ext2_free_inode: bit already cleared for inode 83966 and the machine needs to be hard rebooted. On both the systems SCSI emulation with usb_storage driver is being used to detect the module. Here is the output of /proc/scsi/scsi on 2.4: # cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 02 and on 2.6: # cat /proc/scsi/scsi Attached devices: Host: scsi6 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 00 i.e. only 'ANSI SCSI revision:' is shown as different, although I am not sure if this can cause any problem. Really appreciate if someone can point as to how to debug this issue or any mailing list where I can further ask questions about this.

  Read the article

• Git repo: Unravelling my mess into tidy branches

  - by Martin

  I wanted to play with a project, so git cloned it and, following its instructions, created a local branch for my configuration (I guess so that users can merge updates back). At first I was just tweaking to suit my preferences, so I didn't bother with any further branching, but now I have some code that might be useful to someone else, but with my passwords, etc in the same branch. Effectively, I have one big branch from which I'd like to have: Postgres backend (default) but with some new code I've added MySQL backend (the biggest change I've made) with that same new code My settings: I can't git ignore the settings file because I occasionally have to add sections for new functionality, but I need to keep my personal settings out of the public branches! I guess this would work best as a local-only branch. Dev branches, which I would branch from the MySQL. Starting from scratch, I think I could figure out how to branch/merge the various updates, but is there an easy way to walk through the existing repo and choose which commits to apply to which branch? Or possibly create a branch from a point upstream then merge back, excluding certain commits?

  Read the article

• Start a new project. Where is the inspiration ?

  - by Kakawait

  The question may seem strange at first glance ... And I may be alone in this situation. But currently I want to improve my skill through learning new framework. however, do a simple "HelloWorld" application does not satisfy me. I think a practical project is required to apprehend the basics of a framework. I know there is many scholar-like project like design a library manager or CMS. But I have recently planned to learn ~3 differents frameworks and I can't find any motivations through "unexciting" project. In the end I have not started any framework ... I'm aware of I do not develop the project of the year ... I'm just looking for something a bit exciting. I do not expect any project subject, anyway stimulation provided by a project is something subjective. But I want to know your inspiration ! (or method to learn framework ^^) I'm talking about web-dev framework but I'm open to any kind information ! Kind regards.

  Read the article

• Resource Acquisition is Initialization in C#

  - by codeWithoutFear

  Resource Acquisition Is Initialization (RAII) is a pattern I grew to love when working in C++.  It is perfectly suited for resource management such as matching all those pesky new's and delete's.  One of my goals was to limit the explicit deallocation statements I had to write.  Often these statements became victims of run-time control flow changes (i.e. exceptions, unhappy path) or development-time code refactoring. The beauty of RAII is realized by tying your resource creation (acquisition) to the construction (initialization) of a class instance.  Then bind the resource deallocation to the destruction of that instance.  That is well and good in a language with strong destructor semantics like C++, but languages like C# that run on garbage-collecting runtimes don't provide the same instance lifetime guarantees. Here is a class and sample that combines a few features of C# to provide an RAII-like solution: using System; namespace RAII { public class DisposableDelegate : IDisposable { private Action dispose; public DisposableDelegate(Action dispose) { if (dispose == null) { throw new ArgumentNullException("dispose"); } this.dispose = dispose; } public void Dispose() { if (this.dispose != null) { Action d = this.dispose; this.dispose = null; d(); } } } class Program { static void Main(string[] args) { Console.Out.WriteLine("Some resource allocated here."); using (new DisposableDelegate(() => Console.Out.WriteLine("Resource deallocated here."))) { Console.Out.WriteLine("Resource used here."); throw new InvalidOperationException("Test for resource leaks."); } } } } The output of this program is: Some resource allocated here. Resource used here. Unhandled Exception: System.InvalidOperationException: Test for resource leaks. at RAII.Program.Main(String[] args) in c:\Dev\RAII\RAII\Program.cs:line 40 Resource deallocated here. Code without fear! --Don

  Read the article

• Models, collections...and then what? Processes?

  - by Dan

  I'm a LAMP-stack dev who's been more on the JavaScript side the last few years and really enjoying the Model + Collection approach to data entities that BackboneJS, etc. uses. It's helped me organize my code in such a way that it is extremely portable, keeping all my properties and methods in the scope (model, collection, etc.) in which they apply. One thing that keeps bugging me though is how to organize the next level up, the 'process layer' as you might call it, that can potentially operate on instances of either models or collections or whatever else. Where should methods like find() (which returns a collection) and create() (which returns a model) reside? I know some people would put a create() in the Collection prototype, but while a collection operates on models I don't think it's exactly right to create them. And while a find() would return a collection I don't think it correct to have that action within the collection prototype itself (it should be a layer up). Can anyone offer some examples of any patterns that employ some kind of OOP-friendly 'process' layer? I'm sorry if this is a fairly well-known discussion but I'm afraid I can't seem to find the terminology to search for.

  Read the article

• Relation between developers and clients

  - by guiman

  Hi everyone, i've been facing a situation at work and i would like to share it with you and tell me: Did you had to do it to? Should a developer be in direct contact wit the client? Or there should be an "adapter" guy that translates client needs in pseudo formal requirements understandable to us? I'm currently working in a small company that its taking care of implementing lots of systems, most of them for goverment institutions, in witch it generally means taking software developted 20 years ago and refurbish them so fit up-to-date needs. The clients generally are very used to them and tend to discourage change (they are in their 50s 60s give or take, so not technologie-friendly in general). As you can imagine, dev-team in most cases starts taking care of relation with clients, generating the documentation needed in this cases (CU usually), assisting to weekly meets to see improvements with clients. As for experience, this is a gold mine for me, because gives a nice perspective on all the aspects of software development, but also some problems rise because, if developers come from mars then client are from venus. So there is a fine gap on the vocabulary/experience/capability-to-interpret-needs that generates an noice in the communication, and some times affecting the final product.

  Read the article

• Ubuntu 14.04: Fine tuning Touchpad for ThinkPad S431

  - by ramgorur

  I am using Ubuntu 14.04 on Lenovo ThinkPad S431. The touchpad is very bumpy, tricky to use. Slides down with a small touch, sometimes jerks erratically. I have tried to modify the settings in /usr/share/X11/xorg.conf.d/50-synaptics.conf file as below -- Section "InputClass" Identifier "touchpad catchall" Driver "synaptics" MatchIsTouchpad "on" MatchDevicePath "/dev/input/event*" Option "JumpyCursorThreshold" "250" Option "VertResolution" "100" # Option "HorizResolution" "65" # Option "MinSpeed" "1" # Option "MaxSpeed" "1" # Option "AccelerationProfile" "1" # Option "AdaptiveDeceleration" "8" # Option "ConstantDeceleration" "1" # Option "VelocityScale" "128" Option "HorizHysteresis" "150" Option "VertHysteresis" "150" EndSection There are lots of options here, does anyone know how to get a fine-tuned values for the above options (for ThinkPad S431)? The Hysteresis values seems to alleviate the problem a little bit, but failed to get a perfect result. EDIT: According to this bug report for ThinkPad X230 (+X230t), I set these values and quite good for now -- Option "VertResolution" "100" Option "HorizResolution" "65" Option "MinSpeed" "1" Option "MaxSpeed" "1" Option "AccelerationProfile" "2" Option "AdaptiveDeceleration" "16" Option "ConstantDeceleration" "16" Option "VelocityScale" "32" Option "HorizHysteresis" "50" Option "VertHysteresis" "50" and then you need to increase the cursor speed manually from the Unity mouse settings. But I am still looking for a fully functional (possibly with all the gestures) and a fine-tuned touchpad settings for S431. Further help is appreciated.

  Read the article

• Grub menu not waiting despite of GRUB_TIMEOUT=10

  - by Optimus

  I have Ubuntu 12.04 installed along side of windows 7. The grub menu doesn't seem obey GRUB_TIMEOUT=10, I see the grub menu there for a split second and it immediately defaults to the first option. Grub menu worked fine when I first installed ubuntu. I am not able to pinpoint what exactly broke it(maybe some update?). I did resize my ubuntu partition using gparted but am not sure if that is what caused it. here are my settings from etc/default/grub GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 #GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" How do I fix this? Edit: As suggested by 'kamil' this is what I have tried so far with no luck - 1) hold the shift key while booting 2) sudo gedit /etc/default/grub edit GRUB_TIMEOUT to `GRUB_TIMEOUT=10` sudo update-grub 3) sudo gedit /etc/default/grub edit GRUB_TIMEOUT to `GRUB_TIMEOUT=10` sudo update-grub2 4) at the end of your /etc/grub.d/00_header file, comment out the if condition except for the regular set timeout line like this: #if [ \${recordfail} = 1 ]; then # set timeout=-1 #else set timeout=${GRUB_TIMEOUT} #fi then sudo update-grub and sudo update-grub2 5) install boot repair sudo add-apt-repository ppa:yannubuntu/boot-repair sudo apt-get update sudo apt-get install -y boot-repair boot-repair boot-repair output - Boot successfully repaired. ... The boot files of [The OS now in use - Ubuntu 12.04.1 LTS] are far from the start of the disk. Your BIOS may not detect them. You may want to retry after creating a /boot partition (EXT4, 200MB, start of the disk). This can be performed via tools such as gParted. Then select this partition via the [Separate /boot partition:] option of [Boot Repair]. (https://help.ubuntu.com/community/BootPartition) http://paste.ubuntu.com/1220468/ - here is the full boot-repair data Could grub files not being at the start of the disk create such issues?

  Read the article

< Previous Page | 216 217 218 219 220 221 222 223 224 225 226 227  | Next Page >