Search Results

Search found 7627 results on 306 pages for 'grand theft auto'.

Page 224/306 | < Previous Page | 220 221 222 223 224 225 226 227 228 229 230 231  | Next Page >

• Cannot browse remote networks even with WINS configured

  - by paradroid

  As the NetBIOS protocol acts on Layer 2 and so is not routable, In order to enable network browsing of remote networks, WINS has been installed and configured on two domain controllers, both of which are on different networks. The WINS servers seem to be replicating with eachother, and each has 127.0.0.1 set as the Primary WINS Server in each of their LAN interface properties, with nothing entered for Secondary WINS Server. The DC which holds the PDC Emulator FSMO role has the Computer Browser service running and set to Auto start, and it has the WINS/NBT node type network setting at 0x8 (H-node - Hybrid node). Remote network browsing does not work. Is the WINS/NBT node type correct for this scenario? The reason why I think it may not be the right one is because I set the DHCP Server's 046 WINS/NBT node type option to 0x8 as well, after which the DHCP clients started to disappear from the Network folders. When that option is not set, does it default to B-node (Broadcast node)? Or could it be a problem with the WINS servers setup?

  Read the article

• Ubuntu second static IP, ifconfig, /etc/network/interfaces

  - by Schmoove

  I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

  Read the article

• hosts.deny not blocking ip addresses

  - by Jamie

  I have the following in my /etc/hosts.deny file # # hosts.deny This file describes the names of the hosts which are # *not* allowed to use the local INET services, as decided # by the '/usr/sbin/tcpd' server. # # The portmap line is redundant, but it is left to remind you that # the new secure portmap uses hosts.deny and hosts.allow. In particular # you should know that NFS uses portmap! ALL:ALL and this in /etc/hosts.allow # # hosts.allow This file describes the names of the hosts which are # allowed to use the local INET services, as decided # by the '/usr/sbin/tcpd' server. # ALL:xx.xx.xx.xx , xx.xx.xxx.xx , xx.xx.xxx.xxx , xx.x.xxx.xxx , xx.xxx.xxx.xxx but i am still getting lots of these emails: Time: Thu Feb 10 13:39:55 2011 +0000 IP: 202.119.208.220 (CN/China/-) Failures: 5 (sshd) Interval: 300 seconds Blocked: Permanent Block Log entries: Feb 10 13:39:52 ds-103 sshd[12566]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12567]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12568]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12571]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:53 ds-103 sshd[12575]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root whats worse is csf is trying to auto block these ip's when the attempt to get in but although it does put ip's in the csf.deny file they do not get blocked either So i am trying to block all ip's with /etc/hosts.deny and allow only the ip's i use with /etc/hosts.allow but so far it doesn't seem to work. right now i'm having to manually block each one with iptables, I would rather it automatically block the hackers in case I was away from a pc or asleep

  Read the article

• Suspected brute force attack

  - by HarveySaayman

  Recently I acquired a dedicated server from a local ISP to play around with. As the tags suggest, its a windows server 2008 R2 machine. I've only had it for a few days, and no real traffic is going to it yet. I haven't even deployed a "real" website to it yet. Just a silly page so that I could check IIS, my host headers, DNS records, etc are all configured correctly. While playing around, I noticed a ton of Audit Failure entries in the event viewers security logs. It seems something is trying to access the administrator account, and failing. It smells like a brute force attack to me. My ISP gave me the account details of the administrator account and I used those to RDP into the box, which I've heard is not the securest of situations. I created myself another account and added myself to the administrator group, so im using that account to gain acceess to the machine now. In response to all of this i used http://strongpasswordgenerator.com/ to generate me some 20 character length strong passwords and changed all of my account passwords, even the SQL sa user. I also enabled the auto ban feature of FileZillaServer (my FTP server) My questions: 1) how can i detect this kind of thing better? 2) how can i protect my server from unauthorized access better? PS: I'm a software dev, not a sysadmin so please mind my server security idiot-ness-ness

  Read the article

• Two parts: linux startup script to connect to bluetooth and cron to keep it connected

  - by D.R.

  I have a mini bluetooth keyboard and a Raspberry Pi running a Debian-based distro. I know the MAC address of the keyboard but for this question, let's just use AA:BB:CC:DD:EE:FF. Right now I have to have a wired keyboard connected as well as my bluetooth dongle for the mini-keyboard and on the wired keyboard, I have to run the following when the device boots up: sudo hidd --connect AA:BB:CC:DD:EE:FF If the device goes idle for too long, then the bluetooth disconnects and I have to pull out my wired keyboard and retype that same command. What I'm looking for it a way to have that command run at startup and a way to sense if it gets disconnected so that it will auto reconnect. The annoying thing is that they keyboard has to be in pairing mode (even though it has already been paired) when I run that command, otherwise it tells me the host is down. So perhaps the script needs to prevent it from disconnecting due to inactivity, otherwise I'll have to put it back in pairing mode to reconnect. So to recap: - A script to connect at startup (I can make sure to put the keyboard into pairing mode before turning it on) - A script to prevent it from disconnecting (maybe some sort of signal to send to it every 60 seconds or something?) Any help with this is greatly appreciated! StackOverflow is always the best place to find answers to weird questions! I've been searching long and hard for an answer, but finally had to resort to coming here! Thanks!

  Read the article

• Optical Audio out stuck on on a MacBook

  - by Clinton Blackmore

  Apple have made an interesting headphone port for the MacBook (and some other Intel Mac models). It works like a standard jack: nothing plugged in - audio comes out of built-in speakers headphones/external speakers plugged in - plays through headphones/external speakers but you can also use a special adapter (which trips a tiny microswitch) to get an optical audio out signal (which you can presumably plug into a nice surround-sound system). This is all well and good except when, like auto-tracking, it doesn't work, and you are left with nothing to adjust. Users report that they get no sound when they have nothing plugged in and that a red light emanates from the headphone port. If you go to System Preferences - Sound - Output, it will say (IIRC) "Optical Out" instead of "Internal Speakers". The only solution I'm aware of is to try to reset the switch by inserting and removing a set of headphones or a toothpick, perhaps wiggling it inside of the port, and hoping that you luck out and get it. Are there other ways to fix this problem? Does anyone know where the microswitch is or have a good technique to reset it?

  Read the article

• Facing error: "Could not open a connection to your authentication agent."; trying to add ssh-key.

  - by Kaustubh P

  I use ubuntu server 10.04. ssh-add /foo/cert.pem gave the following output Could not open a connection to your authentication agent. These are my running processes: ps -aux | grep ssh Warning: bad ps syntax, perhaps a bogus '-'? See http://procps.sf.net/faq.html root 1523 0.0 0.0 49260 632 ? Ss Dec25 0:00 /usr/sbin/sshd root 10023 0.0 0.3 141304 6012 ? Ss 12:58 0:00 sshd: padmin [priv] padmin 10117 0.0 0.1 141304 2400 ? S 12:58 0:00 sshd: padmin@pts/1 padmin 11867 0.0 0.0 7628 964 pts/1 S+ 13:06 0:00 grep --color=auto ssh root 31041 0.0 0.3 141264 5884 ? Ss 11:24 0:00 sshd: padmin [priv] padmin 31138 0.0 0.1 141264 2312 ? S 11:25 0:00 sshd: padmin@pts/0 root 31382 0.0 0.3 139240 5844 ? Ss 11:26 0:00 sshd: padmin [priv] padmin 31475 0.0 0.1 139372 2488 ? S 11:27 0:00 sshd: padmin@notty padmin 31476 0.0 0.0 12468 964 ? Ss 11:27 0:00 /usr/lib/openssh/sftp-server These are my environment variables: $ env | grep SSH SSH_CLIENT=192.168.1.13 42626 22 SSH_TTY=/dev/pts/1 SSH_CONNECTION=192.168.1.13 42626 192.168.1.2 22 What is wrong? Why cant I add any identities? Thanks.

  Read the article

• when should be choose simple php mail and when smpt with loggin+password?

  - by user43353

  Hi, My Case: web application that need to send 1,000 messages per day to main gmail account. (Only need to send email, not need receive emails - email client) 1. option - use php mail function + sendmail + config php.ini php example: <?php $to = '[email protected]'; $subject = 'the subject'; $message = 'hello'; $headers = 'From: [email protected]' . "\r\n" . 'Reply-To: [email protected]' . "\r\n" . 'X-Mailer: PHP/' . phpversion(); mail($to, $subject, $message, $headers); ?> php.ini config (ubuntu): sendmail_path = /usr/sbin/sendmail -t -i pros:don't need email account, easy to setup cons:? 2. option - use Zend_Mail + transport on smpt+ password auto php example(need include Zend_Mail classes): $config = array('auth' => 'login', 'username' => 'myusername', 'password' => 'password'); $transport = new Zend_Mail_Transport_Smtp('mail.server.com', $config); $mail = new Zend_Mail(); $mail->setBodyText('This is the text of the mail.'); $mail->setFrom('[email protected]', 'Some Sender'); $mail->addTo('[email protected]', 'Some Recipient'); $mail->setSubject('TestSubject'); $mail->send($transport); pros:? cons:? Questions: Can 1 option be filtered by gmail email server as spam? please can you add pros + cons to options above Thanks

  Read the article

• How to fake ip at localhost without LoopBack.

  - by sexer

  How can i fake an ip on my own PC? for example if there were an ip address lets say 201.91.81.71, that Host is somewhere outside of my red and is hosting a webserver. How can set a website on my own PC, and when i go to browser and try to explore 201.91.81.71 it actually explore the website at my own PC? pd: I need it with IP addresses not domain names, since I need to implement it on a non-web service. First guess was installing a LoopBack with 201.191.81.71 as ip, but since some times the subnet works and some other it doesn't isn't a stable solution. Second guess was adding a route to route table : route add 201.91.81.71 mask 255.255.255.255 192.168.1.2 192.168.1.2 is the ip address of my NIC. If i could add this route it would work but windows doesn't let me do so. route add 201.91.81.71 mask 255.255.255.255 127.0.0.1 it doesn't let me set as gateway 127.0.0.1 if 201.91.81.71 isn't set in a NIC, so thats why i set sometimes loopback and this route add is auto, but it needs a subnet mask which doesn't match the ip and cannot set 255.255.255.255, im in real throubles here. can i get some help? thx.

  Read the article

• NIC are not advertising Correct Speeds

  - by Squidly

  I have an IBM x336 that is not advertising the proper LINK speeds. One interface is the other is not. I've tried to Force it to 1000/Full but then it just shows link down. I have confirmed the switch is set to auto negotiate like my switches. I have also changed out my Ethernet Cables. I'm at a loss where to look further. I have verified that it will connect at 1G on a different swtich. This also has happened on two different servers on the same switch. This is my output from mii-tool -v for each interface. eth0: negotiated 100baseTx-FD, link ok product info: vendor 00:08:18, model 24 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD eth1: negotiated 1000baseT-FD flow-control, link ok product info: vendor 00:08:18, model 24 rev 0 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 1000baseT-HD 1000baseT-FD 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

  Read the article

• L2TP over IPSec VPN with OpenSwan and XL2TPD can't connect, timeout on Centos 6

  - by Disco

  I'm setting up LT2p over IPSec on my Centos 6.3 fresh install. I have iptables flushed, permit all. Whenever I try to connect, i get a 'no reply from vpn' and nothi Here's my ipsec.conf file (Server is 1.2.3.4) : config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off protostack=netkey conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 rekey=no ikelifetime=8h keylife=1h type=transport left=1.2.3.4 leftprotoport=17/1701 right=%any rightprotoport=17/%any My /etc/ipsec.secrets 1.2.3.4 %any: PSK "password" My sysctl.conf (appened lines) net.ipv4.ip_forward = 1 net.ipv4.conf.default.rp_filter = 0 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.default.send_redirects = 0 net.ipv4.conf.all.log_martians = 0 net.ipv4.conf.default.log_martians = 0 net.ipv4.conf.default.accept_source_route = 0 net.ipv4.conf.all.accept_redirects = 0 net.ipv4.conf.default.accept_redirects = 0 net.ipv4.icmp_ignore_bogus_error_responses = 1 Here's what 'ipsec verify' gives: # ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.32/K2.6.32-279.19.1.el6.x86_64 (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing for disabled ICMP send_redirects [OK] NETKEY detected, testing for disabled ICMP accept_redirects [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] And I see xl2tpd is listening on 1701/udp : udp 0 0 1.2.3.4:1701 0.0.0.0:* 2096/xl2tpd

  Read the article

• My Boot order changed. Why?

  - by Chris

  I have a laptop running Windows XP SP3 with one internal hard drive partitioned into C: (system), D: (storage) and I have an external hard drive, F: (external drive). Yesterday the machine was running fine. Today, I go back to it and see that it's just showing a blinking cursor. Checked through the BIOS and the hard drive checked out fine. CTRL-ALT-DELETED the machine a few times, but I was never able to boot back into the operating system. I threw in a live CD and found out that the boot order of the drives has changed. The external drive is now C:, the system partiton is D:, and the storage partition is E:. Does anyone have any idea of how or why this would have occured? Auto system updates are turned off so there should have been no automatic reboot of the system overnight, and anti-virius runs on the machine and has found no infections before this occured. Edit When I was looking through the BIOS of the machine, I did see that the boot order was changed. But still the same question remains, what would have caused this to happen? I can't believe that a random reboot happened and totally changed my hard drive setup.

  Read the article

• Cannot find wireless driver for HP laptop

  - by rodey

  I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

  Read the article

• Tidy up old Windows Server Backup snapshots

  - by dty

  Hi, I'm running wbadmin from a scheduled job, backing up my C: and D: drives to my E: and (I believe!) including the system state: wbadmin start backup -backuptarget:e: -include:c:,d: -allCritical -noVerify -quiet I'd like to delete old backups, but I'm concerned that all the information I can find says to use wbadmin to delete old system state backups, and vssadmin to delete other backups. As far as I know, my backups ARE system state backups, but are using VSS on E: for storage, so I'm worried about trying either of these techniques for fear of losing all my backups. This is a home network, so I don't have a spare server to test this on. I'm also happy to simply restrict the space used on E:, but I can't make sense of the difference between the /for and /on parameters of the relevant vssadmin command. For reference, here's the output of vssadmin show shadows: Contents of shadow copy set ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Contained 1 shadow copies at creation time: 07/01/2011 08:12:05 Shadow Copy ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Original Volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Volume: \\?\GLOBALROOT\Device\HarddiskVolumeShadowCopy83 Originating Machine: x.y.com Service Machine: x.y.com Provider: 'Microsoft Software Shadow Copy provider 1.0' Type: DataVolumeRollback Attributes: Persistent, No auto release, No writers, Differential [... repeated a lot...] vssadmin show shadowstorage: Shadow Copy Storage association For volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 5.859 GB Shadow Copy Storage association For volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 40.317 GB Shadow Copy Storage association For volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 168.284 GB Allocated Shadow Copy Storage space: 171.15 GB Maximum Shadow Copy Storage space: UNBOUNDED wbadmin get versions: Backup time: 07/01/2011 03:00 Backup target: 1394/USB Disk labeled xxxxxxxxx(E:) Version identifier: 01/07/2011-03:00 Can Recover: Volume(s), File(s), Application(s), Bare Metal Recovery, System State [... repeated a lot...]

  Read the article

• How does one make sure or even guarantee server time are sync correctly between dozens of servers across multiple datacenter on different location?

  - by forestclown

  Currently our web applications contain a logic to check if the data sent to the web server is expired or not by comparing the timestamp of the data with the date/time of the server. Everything goes will, until some dude from data center accidentally modify one of the web server date/time and causes some disruptions in our web services. My managers are of course not happy with this, and said we shouldn't use timestamp to check expiry in the first place...anyway.... Network Time Protocol is implemented, because of data centers are spread across different continents so we have one NTP server in each data center. The servers within the data center will have cron jobs to check against the time with their NTP server from the same data center. If time is out of sync it will auto update the server date/time. But then with our managers not happy with it, and think it could still easily causes the same problem. e.g. what if someone accidentally modify the NTP date/time? what if all the NTP servers are out of sync with each other? which NTP servers we can really trust? and blah blah.. So my questions are: What are the current practice to sync date/time between servers across multiple data centers or locations? How does one manages time stamp between web apps? e.g. Server A send data (contain timestamp of Server A) to Server B (compare timestamp between Server B and the timestamp from the data to see if it has expired or not. This is to avoid HTTP replay) Should we really not use timestamp check? Thanks & Best Regards

  Read the article

• SSD seems dead after wakeup from Windows Sleep, BIOS stalls but doesn't find it anymore

  - by Abel

  The morning, the following scary scenario happened: I woke up my Windows system Typed in my username and got an error (something like "could not load security xxx", but unsure of exact wording) System auto-restarted after cliking OK It didn't boot up anymore to the SSD with Windows 7 OS (I have another disk I can boot to, but that doesn't see the disk either). Obviously, this happened right after I instantiated a backup procedure, which hasn't succeeded either. The BIOS can't find the drive when I connect to SATA. And it can't find the drive when I connect it to SAS. I have a Dell Workstation T7400, most recent BIOS (version A06), version of SAS Host Bus Adapter BIOS (HBA) is MPTBIOS 6.14.10.00 (2007.09.29) from LSI Logic Corp. Other findings: When connecting to SATA, the DELL Logo screen stays really long (5 minutes) and then at the end of POST it says that a drive is not found When connecting to SAS, the SAS HBA initializing phase takes long (2 minutes, against normally 15 seconds) When running Dell Diagnostics, it doesn't finish and gives the error Exception occurred in module MPCACHE.MDM file "IOAPICSP.ASM" line 1645. I contacted Dell. On their advice I tried different slots and different cables to no avail. I use an APIC battery power, spikes in the power are thus unlikely. My conclusion so far: the disk is dead. I need this disk very badly because it contains the last few days of important development of which not all code was checked in the moment this happened. Are there any ways to recover dead SSD drives? The drive is a new X25-M G2 160GB model SSDSA2M160G2GC 2.5" in an extension bay and has been running without issues for 3 months on SAS.

  Read the article

• What am I doing wrong in my config for MySql?

  - by Knight Hawk3

  When I load my my.conf with the config at the bottom Mysql fails to start and prints no errors. I am running Arch Linux (Updated) with the latest MySQL (5.5) and the latest nginx (Well latest in the repository, Not sure how to check. Only installed it today) I will give you any info you ask for. Thanks for helping! # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /var/run/mysqld/mysqld.sock # Here follows entries for some specific programs # The MySQL server [mysqld] port = 3306 socket = /var/run/mysqld/mysqld.sock skip-locking key_buffer = 16K max_allowed_packet = 1M table_cache = 4 sort_buffer_size = 64K read_buffer_size = 256K read_rnd_buffer_size = 256K net_buffer_length = 2K thread_stack = 64K # Don’t listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (using the “enable-named-pipe” option) will render mysqld useless! # #skip-networking server-id = 1 # Uncomment the following if you want to log updates #log-bin=mysql-bin # Uncomment the following if you are NOT using BDB tables skip-bdb # Uncomment the following if you are using InnoDB tables #innodb_data_home_dir = /var/lib/mysql/ #innodb_data_file_path = ibdata1:10M:autoextend #innodb_log_group_home_dir = /var/lib/mysql/ #innodb_log_arch_dir = /var/lib/mysql/ # You can set .._buffer_pool_size up to 50 – 80 % # of RAM but beware of setting memory usage too high #innodb_buffer_pool_size = 16M #innodb_additional_mem_pool_size = 2M # Set .._log_file_size to 25 % of buffer pool size #innodb_log_file_size = 5M #innodb_log_buffer_size = 8M #innodb_flush_log_at_trx_commit = 1 #innodb_lock_wait_timeout = 50 skip-innodb [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [isamchk] key_buffer = 1M sort_buffer_size = 1M [myisamchk] key_buffer = 1M sort_buffer_size = 1M [mysqlhotcopy] interactive-timeout So what is my silly error?

  Read the article

• Port forwarding + shared connection with Ubuntu

  - by Joey Adams

  Because my wireless router's ethernet ports are defective, I set up a shared wireless connection from my laptop (which has wifi) to my eMac (which does not) via a crossover ethernet cable. The laptop is behind a router as 192.168.1.131, and the eMac is behind the laptop as 10.42.43.1 . The laptop is running Ubuntu 9.10 (Karmic). I achieved the shared connection through NetworkManager Applet. I right-clicked on the network icon at the topright, went to Edit Connections, selected the Wired connection named "Auto eth0", clicked "Edit...", went to the "IPv4 Settings" tab, and selected the Method "Shared to other computers". The eMac can now access the Internet. Now I want to enable port forwarding. There's a game I want to play that needs port 6112 forwarded (both TCP and UDP) in order to host games. I set up the router to enable port forwarding for 192.168.1.131 (the laptop), but port forwarding still isn't available on the eMac. I suppose I need to pretend my laptop is a router and configure port forwarding on it, indicating that incoming connections to the laptop (192.168.1.131) should be forwarded to the eMac on the shared connection (10.42.43.1 ). Thus, packets coming into the router on port 6112 would be redirected to the laptop (by the router), then to the eMac (by the laptop). My question is, how would I do that on Ubuntu (in light of NetworkManager's presence)? Also, if I can't get this to work, does anyone mind hosting a comp stomp? :D

  Read the article

• Samba4/Ubuntu Shares Incorrectly Available to All Users

  - by Dan

  I've got my Ubuntu server working with Samba4 and got it set up as the Primary domain controller on my network with AD and all that goodness. However, I'm trying to get my Samba configuration to work with the users and groups I've defined with the Active Directory tools from Windows. For instance, I've got a share X which I want users A and B (as part of the 'management' group, known as LLGrpManager in my setup) to see, but no body else. However, after making changes to the configuration, restarting Samba, I test by connecting to the share with my Mac over Samba as user 'C' which isn't part of the management group, and I can, incorrectly, see the X share. I've tried alsorts of combinations of specifying the group with no luck at all. I've got a feeling that my global config might be too lenient or something to do with file permissions but being a bit green, I'm without clue. My /etc/samba/smb.conf # Global parameters [global] server role = domain controller server string = Office Server workgroup = LLDOMAIN realm = lldomain.local netbios name = DUMBO passdb backend = samba4 logon path = \\%L\profiles\%U logon drive = L: log file = /var/log/samba/%m.log max log size = 50 security = ads domain logons = yes domain master = auto usershare allow guests = no valid users = %S [netlogon] path = /var/lib/samba/sysvol/lldomain.local/scripts read only = no guest ok = no [sysvol] path = /var/lib/samba/sysvol read only = No guest ok = no valid users = @LLDOMAIN\LLGrpManager [ShareX] path = /data comment = Entire Data Volume guest ok = no comment = Entire Data Volume guest ok = no valid users = @LLDOMAIN\LLGrpManager admin users = @LLDOMAIN\LLGrpManager browsable = no inherit acls = yes inherit permissions = yes ... My /etc/nsswitch.conf I've also instructed the system to use the nss winbind library when searching for users or groups by adding the stanza passwd and group in /etc/nsswitch.conf: passwd: compat winbind group: compat winbind shadow: compat Permissions on the folder in question drwxrwxrwt 8 root root 4.0K Oct 28 19:11 data

  Read the article

• Hudson deploy specific git revision

  - by brad

  I'm using hudson to auto-deploy my Rails app to heroku. In my main build job I pull from a Git repo (hosted using gitosis on the same machine), master branch with the following: URL of repository: /home/git/repositories/my_app.git Name of repository: origin Refspec: +refs/heads/master:refs/remotes/origin/master Branches to build: master Then, assuming all tests pass, I want to kick off a new build that is the deploy to Heroku. I can't however figure out how to get that deploy build to checkout the particular revision that this build was using. I understand there's a parameterized trigger plugin that would allow me to pass this revision number, but I don't know how I can tell hudson to checkout this particular revision on the deploy build. I'm pretty sure this just has to do with my limited knowledge of git, but where in the hudson git config's is there an option to checkout a particular revision? Otherwise, I could have many commits happen whilst a build is happening, and when it kicks off a deploy build, that deploy build would just check out the HEAD of the branch, which may not be the same as the code that was pushed that triggered this build. I don't fully understand why I have a refspec in Hudson, then also specify a branch to build, I thought this was the same thing. Can refspec somehow specify the revision number? How would this be referenced if it was passed through with the parameterized trigger plugin? (I've never used that plugin, but someone else recommended it as a way to pass in vars to a new build, if there's another way I'm all ears)

  Read the article

• Pin the Dock to the top

  - by Chris Buchholz

  I wonder if it is possible to pin the Mac OS X Dock to the top in Snow Leopard? I see lets of ideas on how to do this when I google for it, and Secrets (the tweaking app) also provide it as an option, but I don't see any of the ways working for me. I guess it must have worked at some point, since people said it did, but I believe this feature might have been removed from Snow Leopard, and therefore does not work for me. Is this so? Is there really no way to pin the Dock to the top of screen? If not, what ways of "getting rid of the dock" can you guys recommend? I have tried with auto-hiding, but my problem is that this will leave a 4px line at the edge of where the Dock is pinned to, that applications wont cover. Thats not ideal for me. As far as I have understood from googling, this line will not appear if the Dock is pinned to the top, hence my question. What other ways do you guys use to get rid of it?

  Read the article

• Is there a program to show programs loading during the boot process in real time?

  - by Gary M. Mugford

  Hi all, There are any number of programs that will show me WHAT will run during the boot process for Windows XP. I've always been partial to Mike Lin's version but there are several others, some of which are quite possibly superior. That's not the issue. What I'd really like is a program that would load first and then would list the programs that were about to load and then check them off as the programs loaded. This isn't something I necessarily need for myself. But certain family members get click happy as soon as they see the icon they eventually want to run and end up clicking on it. THIRTY TWO TIMES in one memorable crash-inducing spasm. If there was some way for 'progress' to be shown during the loading of from the various spots Windows auto-loads from, PLUS a BIG BANNER saying "Please do not move the mouse or click on anything until done.", I think I might cut down on my early morning family support calls significantly. I've tried a variety of searches, but I couldn't find the ones that show in real time in the forest of links to programs that will show the list after the fact. Any leads? If not, do any of you who write the after-the-fact listers want to take a shot at producing a utility to do what I think would be a relatively popular utility? Best of the season to all of you and yours. Thanks in advance for any replies, GM

  Read the article

• How to create partition when growing raid5 with mdadm.

  - by hometoast

  I have 4 drives, 2x640GB, and 2x1TB drives. My array is made up of the four 640GB partitions and the beginning of each drive. I want to replace both 640GB with 1TB drives. I understand I need to 1) fail a disk 2) replace with new 3) partition 4) add disk to array My question is, when I create the new partition on the new 1TB drive, do I create a 1TB "Raid Auto Detect" partition? Or do I create another 640GB partition and grow it later? Or perhaps the same question could be worded: after I replace the drives how to I grow the 640GB raid partitions to fill the rest of the 1TB drive? fdisk info: Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xe3d0900f Device Boot Start End Blocks Id System /dev/sdb1 1 77825 625129281 fd Linux raid autodetect /dev/sdb2 77826 121601 351630720 83 Linux Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc0b23adf Device Boot Start End Blocks Id System /dev/sdc1 1 77825 625129281 fd Linux raid autodetect /dev/sdc2 77826 121601 351630720 83 Linux Disk /dev/sdd: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x582c8b94 Device Boot Start End Blocks Id System /dev/sdd1 1 77825 625129281 fd Linux raid autodetect Disk /dev/sde: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xbc33313a Device Boot Start End Blocks Id System /dev/sde1 1 77825 625129281 fd Linux raid autodetect Disk /dev/md0: 1920.4 GB, 1920396951552 bytes 2 heads, 4 sectors/track, 468846912 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk identifier: 0x00000000

  Read the article

• Can I use multiple URLs in the URL field of KeePass?

  - by Sammy

  I am using KeePass version 2.19. What I would like to do is have more than just one URL address associated with a given user name and password. The entry for a given website might look something like this... Title google User Name email Password pass URL https://accounts.google.com/ServiceLogin?hl=en&continue=https://www.google.com/ https://accounts.google.com/ServiceLogin?hl=sv&continue=https://www.google.com/ https://accounts.google.com/ServiceLogin?hl=de&continue=https://www.google.com/ As you can see the ?hl=en changes into ?hl=sv and then to ?hl=de for the three different languages in which I wish to view the Google log-in page. But this of course could be something completely different, like different web services from the same provider like YouTube and Gmail by Google. Very much like SE where you have several websites but only use one user name and password. I imagine something along the lines of having multiple entries for one and the same website, where KeePass would actually prompt you to choose which one you want to use. So you have several user names and passwords that use the same URL. But is it possible to have several URLs using the same user name and password, so that KeePass asks me "to which of the following three URLs do you want to auto-log into with this password"?

  Read the article

• IPSec Tunnel to Amazon EC2 - Netkey, NAT, and routing issue

  - by Ernest Mueller

  I'm working on getting an IPSec VPN working between Amazon EC2 and my on-premise. The goal is to be able to safely administer stuff, up/download data, etc. over that tunnel. I have gotten the tunnel up in openswan between a Fedora 12 instance with an elastic IP and a Cisco router that's also NATted. I think the ipsec part is OK, but I'm having trouble figuring out how to route traffic that way; there's no "ipsec0" virutal interface because on Amazon you have to use netkey and not KLIPS for the vpn. I hear iptables may be required and I'm an iptables noob. On the left (Amazon), I have a 10. network. Box 1 is privately 10.254.110.A, publically IP 184.73.168.B. Netkey tunnel is up. Box 2 is publically 130.164.26.C, privately 130.164.0.D And my .conf is: conn ni type= tunnel authby= secret left= 10.254.110.A leftid= 184.73.168.B leftnexthop= %defaultroute leftsubnet= 10.254.0.0/32 right= 130.164.26.C rightid= 130.164.0.D rightnexthop= %defaultroute rightsubnet= 130.164.0.0/18 keyexchange= ike pfs= no auto= start keyingtries= 3 disablearrivalcheck=no ikelifetime= 240m auth= esp compress= no keylife= 60m forceencaps= yes esp= 3des-md5 I added a route to box 1 (130.164.0.0/18 via 10.254.110.A dev eth0) but that doesn't do it for predictable reasons, when I traceroute the traffic's still going "around" and not through the vpn. Routing table: 10.254.110.0/23 dev eth0 proto kernel scope link src 10.254.110.A 130.164.0.0/18 via 10.254.110.178 dev eth0 src 10.254.110.A 169.254.0.0/16 dev eth0 scope link metric 1002 Anyone know how to do the routing with a netkey ipsec tunnel where both sides are NATted? Thanks...

  Read the article

< Previous Page | 220 221 222 223 224 225 226 227 228 229 230 231  | Next Page >