Search Results

Search found 20264 results on 811 pages for 'home networking'.

Page 225/811 | < Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >

  • Cisco 861 Router forces one-to-one NAT

    - by Slurpee
    I have a cisco 861 router that only allows one-to-one NATs in order to access the Internet. I would like for computers to get an address via DHCP from this router, and be able to access the Internet without needing to set a static NAT to one of my public IPs. What is wrong with the configuration? I have a basic understanding of the IOS CLI, most of the configuration file (edited for content) was created by my company's long gone Senior Network Engineer.

    Read the article

  • How to see all nics in Solaris 8/9

    - by help_me
    I have a questions regarding how to see all NICS in the solaris 8/9 SPARC boxes. Even if they are active/inactive. dladm show-link command does not work. cat /etc/path_to_inst could but it's hard to make out the NICS. Also when a cable is disconnected from the NIC ifconfig -a still shows the NIC as "UP/RUNNING" without looking at the system message, is there a way to know that the NIC is unplugged? Thank you!

    Read the article

  • Am I supposed to assign the broadcast IP somewhere?

    - by pvieira
    This is a very basic question from a newbie point of view. I have a dedicated server at Hetzner running Windows 2008 R2. I bought a subnet of IP addresses to use in this server. They provided me a given range of IPs, incluind one Ip labeled as "Broadcast". I know how to assign those IPs to the NIC, but should I do something with the Broacast IP, like configure it somewhere on Windows? Or can I just ignore it and I'll be fine? This IP range will be used to host SSL sites.

    Read the article

  • Network outage caused by SMC8013WG Cable Modem/Router ?

    - by mkocubinski
    At work, we have a basic Class C Network. The gateway/router is a SMC8013WG (stock comcast commercial cable modem), and simple unmanaged switch (HP Pro Curve 1400 24G). The SMC8013WG is our default gateway as well as DHCP server. Periodically, I'd say almost every other day.. the entire network will just stop responding. I won't be able to ping/see the gateway, any computers on our local network, or anything on the internet. The only way to fix this is to unplug the Comcast cable modem, wait, and plug back in. This unfailingly fixes the problem. But this doesn't make much sense to me.. shouldn't the network still be fine locally, since everything is plugged into the switch anyway? Why would resetting the router fix this? Can anyone suggest anything to check to in order to narrow this problem down? Just to be clear.. here is the basic topology: { Internet } -- (12.345.67.89) Comcast Cable Modem (192.168.1.1) -- Switch -- 192.168.1.2-254 P.S. Our IT guy is in about 3 hours a day every other week or so, so.. we're kind of on our own most of the time.

    Read the article

  • VPC on Windows 7 very slow network

    - by Shigg
    I have a Windows 2003 virtual machine which I use for website testing. I've just installed Windows 7 and am using the new version VPC (not xp mode). When I try to copy a file - I need to copy some big databases across - I get a file copy speed of about 20k per sec. Copying from one PC to another on the real network transfers files at 13mb per second. Any ideas what may be causing this? I've turned off differential network compression on win 7. The Virtual HD is on a seperate physical drive to the OS. Running Windows 7 64 bit on a dual xeon with 16gb ram and 10,000 rpm drives. Tried installing VPC 2007 but windows blocks it running saying its not compatable. Many thanks for any ideas.

    Read the article

  • Playing games over RDP and utilizing other res of powerfull PC... [closed]

    - by Alex
    Possible Duplicate: Is it possible to run games over remote desktop? Hey guys, I have the one question..that may be not usual but very interesting.. Well, I have laptop and some powerfull PC, now I want to utilize ALL energy of the powerfull PC on my notebook.. for example, run games like F.E.A.R on powefull PC and next play it over the Remote Desktop on my laptop.. both PC may be connected lan < lan, or thru Wi-Fi, or FireWare, or (?) any other way that does not matter.. Google told me that it won't work over RDP due to protocol lacks and there should be many bump on the road on that way.. but, maybe , you guys will give me the right point ? Let's formalzie.. we'd like to utilize all resources of one PC on another PC via network, how we should do that ? Any ideas?

    Read the article

  • Cannot connect to a shared network drive

    - by dublintech
    I am using windows 7, I cannot connect to a shared network drive on another machine. I can ping the machine. I can remote desktop connect to the machine. The machine is on the same subnet My friend with the exact same laptop as me (and on the same network, same workgroup) can connect to the shared folder. The machine I am trying to connect to and my friends machine can both see shared folders on my machine. I also cannot see shared folders on the friends laptop. When I select diagnose, windows tells me nothing useful. When I select see details on the error pop up, I see: Error code: 0x80004005 (google doesn't help much) I can nbtstat -a the machine who has the shared folder. When I try with my firewall turned off the same happens. I have ensured my windows 7 has all updates. I run security essentials to ensure my laptop is clean. I run ccleaner to clean up my registry. Same error. I have tried with my laptop on both wireless and ethernet. As you can imagine, I am banging my head against the wall on this one.

    Read the article

  • lan extension over wide area

    - by avinash
    when we use technology like leased line to extend a lan over a wide area(like when connecting two offices such that hosts in both offices use private ip addresses) , why do we use encapsulations like ppp or hdlc...what can't we use the ethernet header to communicate because mac addresses are unique and can easily be used to identify hosts just like a small area lan... this question may seem a bit absurd but it has been bugging me...so plz explain

    Read the article

  • Folder Permissions in Windows 7

    - by gameshints
    I'm trying to securely share a folder across two computers on a relatively public network. However, I'm a bit confused on how permissions work and was hoping for some clarification between the following so I don't accidentally make something public I don't want. When you right-click a folder and go to properties, what is the difference between Sharing Tab - 'Share...' button - List of users and permissions there Sharing Tab - 'Advanced Sharing...' button - 'Permissions' button - List of users and permissions there Security Tab - List of users and permissions there Thanks!

    Read the article

  • Why should I use a switched network over routed?

    - by SRobertJames
    Now that routers are affordable, why should I build a network using Layer 2 switches, which degenerate to broadcasting under poor conditions, and not just use real routing at Layer 3? Edit: Got some great replies. Let me clarify the question: Of course, at the lowest level, you want to plug your end nodes into a switch, not a router (as demonstrated by AlReece). I'm referring to switches which are used to bridge traffic between segments - that is, switches connected to other switches.

    Read the article

  • Windows Update broke Wirless driver - Can't get it working again

    - by private_meta
    I naively installed a driver update incoming from Windows Updates yesterday. That caused my Wifi on my Notebook (HP ELitebook 2740p) to break. The network is working as I tried it with my other mobile devices. When installing said driver, it told me that the installation failed. I tried to do a system restore, which did not help getting wifi connectivity back. The device said it was working, but did not get any wifi connection and did not discover any networks. What I tried next was to uninstall the device from my Device Manager and install either the current drivers found through windows, then I tried the same with the current drivers on the HP driver page. both of those attempts failed. It always tells me that installation failed when I uninstall and reinstall drivers. If I try to update the broken driver via internet, it tells me it is up to date, and in the device manager it still views as broken. Next, I 'played' around a bit and reinstalled drivers, and I managed to install drivers from 2012, and when trying to update drivers manually and picking drivers that match the device, it lets me choose between drivers from 2010 and 2014. 2014 would be the current one, picking the 2010 driver leads to the driver being accepted. However, no wireless network can be found. I'm pretty much out of ideas by now, short of reinstalling. The only option I can still think of was that the device broke at the exact moment I installed the new windows driver, but I find that a bit unlikely. Any help would be appreciated fixing this issue.

    Read the article

  • How to attach multiple ipv6 ips to eth1 on debian

    - by Noodles
    I've just got a new server with native ipv6. I want to attach multiple ipv6 ips to eth1, but the only way I can see to do so is to attach them individually: i.e. address 2607:f0d0:xxxx:xxxx::2 address 2607:f0d0:xxxx:xxxx::3 address 2607:f0d0:xxxx:xxxx::4 Is it possible to bind whole subnets of ipv6 to a single network interface on debian? My server host tells me I have 18,446,744,073,709,551,616 ipv6 addresses for that server, surely it gets to be a nightmare to manage if they all have to bound individually (plus ifconfig would look messy). Does anyone have a solution?

    Read the article

  • How to control routes added by RasDial

    - by Robert Dodier
    I am using the RasDial function on a Windows box (Windows Server 2008) to dial a device from which the server then reads data. It seems that some new routes are added to the network routing table when the dial-up connection is made. That interferes with other network interfaces on the server. In particular, RasDial adds a default route which routes traffic to the device, which makes the server unreachable until the connection is dropped. Is there a way to control which routes are added by RasDial? I have been studying Microsoft's document for RasDial and associated items (RASDIALPARAMS, RASDIALEXTENSIONS) without finding anything about routing. There is an option for "Use default gateway on remote network" when configuring a VPN, but I don't see how to apply that in this case. Thanks for any light you can shed on this problem.

    Read the article

  • Testifying that somaxconn change can make a difference

    - by petermolnar
    I got into an argument on the net.core.somaxconn parameter: I was told that it will not make any difference if we change the default 128. I believed this might be enough proof: "If the backlog argument is greater than the value in /proc/sys/net/core/somaxconn, then it is silently truncated to that value" http://linux.die.net/man/2/listen but it's not. So does anyone know a method to testify this with two machines, one running, for example MySQL or LVS and the other is hammering it in a GBit network? I'm opened to any solution, scripts are slightly more welcome.

    Read the article

  • How can I monitor network usage by process on Mac OS X?

    - by psmith
    Is there any way to find out which process using how much internet bandwidth on Mac OS X Lion? I'm on mobile internet now, which is not very fast, so it would be nice if I can tell that for example, Chrome using 10kB/s, and Skype using 2kB/s. I can see the total amount of traffic in Activity Monitor, but it is not enough for me. I'd like to use an existing application, not interested to write an app like this. And I'm not interested in the actual traffic, only the number of bytes transferred and received by each processes.

    Read the article

  • Is there Muticast routing support on a Cisco 3750?

    - by mrtechalot
    We have a switch (Cisco WS-C3750G-48TS) with only a C3750-IPBASE-M image (not a 'C3750-IPSERVICES-M' license). Is there any kind of multicast support here? All I need it to do is route multicast packets to an RP (ip pim sparse-mode). Do we really need the service (C3750-IPSERVICES-M) license/image?. The uplink switch is running C3750-IPSERVICES-M, but this switch doesn't seem to carry any ability to configure multicast on an interface.

    Read the article

  • Why would my network slow down?

    - by monkthemighty
    The network at my work has about 40 computers on it and a quite a few printers. When there are a lot of people working the network will be slow. I can test the ping between my computer and the router and it will keep rising, sometimes to the point that it times out. The router we are using is running Ubuntu on a atom processor and it has 4gb of ram. When the network slows the process Ksoftirq will be using most if not all of the processing power. I have found that Ksoftirq is a process that handles irq requests. Also when the network slows down I have captured packets from the router and using tshark and looked at it using wireshark on my laptop. With the capture show a lot of packets with TCP Dup ACK and TCP Retransmissions. The destinations of the TCP Dup and TCP retransmissions are to most of the computers on the network but there are some that are far more than others. What could this problem be caused by?

    Read the article

  • Troubleshoot port forwarding. Could it be ISP blocking incoming connections?

    - by Gravy
    Had a new Axis IP camera delivered yesterday. Plugged into Cisco E2400 Wireless Router but having problems. Example topology: WAN IP: 10.10.10.10 (example) Cisco Router: 192.168.1.1 Axis Camera: 192.168.1.10:80 Port forwarding rules set up on router External Port: 999 Internal Port: 80 Protocol: TCP & UDP Device IP: 192.168.1.10:80 Enabled: True Trying to connect from within the lan to 192.168.1.1:80 from within browser - Works properly. Trying to connect from within the lan to 10:10:10:10:999 from within browser - Works properly. Trying to connect from outside the LAN (e.g. via 3g or another isp) to 10:10:10:10:999 from within browser - Doesnt work. I get the following errors from different machines / browsers: Safari could not open the page because the server stopped responding (IOS) The server at xx.xx.xx.xx is taking too long to respond. (firefox) This problem is not just for the Axis camera. I am also having similar problems connecting to my NAS drive. After using a web based port scanning tool, it appears as though port 999 is closed. Not certain why when I have set up port forwarding within the router. Any troubleshooting suggestions to help me determine whether the problem is with my Cisco settings / firewall or whether it could be my ISP blocking incoming connection requests? Many thanks

    Read the article

  • Monitoring/logging a malfunctioning internet connection

    - by Pekka
    I have a mysterious internet connection problem: Every 15-20 minutes, the connection will become very slow, and take 2-3 minutes for anything to load. I've had a technician from the ISP over here to test the hardware, and everything is in pristine condition. They have no other explanation than a configuration error on my machine, a possibility I can exclude 90% because I'm experiencing the same problems with another machine. I will have to monitor the situation now, and I would like to run a program that logs when internet connections become slow. I thought about putting something together using at and wget. Does anybody know of some other tool for this that does this out of the box - maybe something with an adjustable request frequency, logging connection speeds etc.?

    Read the article

  • SMTP 25 blocked externally

    - by Jeff
    not sure how to title this question... we run an exchange server with around 80 internal users, all outgoing mail is relayed off a smart host (ISP smtp server) so nothing is actually sent to the world via our server. i wanted to check the server, locally i can telnet to port 25 with no issues and receive the esmtp service ready reply. whenever i do it from an external address (off our local network) i receive unable to connect error 10060. can this cause problems with SPF records, and reverse DNS ? should my exchange server be able to accept smtp requests, requiring authentication before i am able to send from external addresses? if so how... also the exchange server is behind a NAT (asa) device, more than likely thinking that the nat is not configured to route the smtp 25 request to the exchange server.. thanks

    Read the article

  • Windows 8 Hidden Downloading? Slow Internet?

    - by EApubs
    After upgrading to Windows 8, im facing a very slow download speed. My router and the NIC is working fine because on the same PC I also have Linux. In Linux, everything works fine. When checking through the task manager, it shows that the system use the full bandwidth 1Mbps even without a download. The process menu doesn't show whats taking much bandwidth. The bitdefender's firewall also shows network activity. Is there any hidden apps downloading? How to fix this?

    Read the article

  • IPTABLES syntax help to forward Remote Desktop requests to a VM [CentOS host]

    - by NVRAM
    I've a VM running MSWindows XP hosted on my CentOS 5.4 machine. I can rdesktop into it from the hosting machine and work just fine using the private ddress (192.168.122.65), but I now need to allow Remote Desktop access from other computers (not just the machine hosting the VM). [Edit] I only need to allow access for a day or so, so don't want to add a NIC (for XP activation reasons). Could someone help me with the iptables syntax? The VM is on a private/virtual network: 192.168.122.65 and my CentOS machine is on a physical network, at 10.1.3.38 (and 192.168.122.1 as the GW for the virtual net). I found this question, but none of the answers seemed to work and I'm a bit timid at blindly trying variations. My FORWARD rules are as listed. Thanks in advance. # iptables -L FORWARD Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable RH-Firewall-1-INPUT all -- anywhere anywhere [Edit] If I do play "blindly" is there a simple way to reset the settings on CentOS (a la service network restart)?

    Read the article

< Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >