Search Results

Search found 23539 results on 942 pages for 'invoke command'.

Page 227/942 | < Previous Page | 223 224 225 226 227 228 229 230 231 232 233 234  | Next Page >

• hp pavilion g6 1250 wireless problems

  - by Ahmed Kotb

  i have tried using ubuntu 10.04 and ubuntu 11.10 and both have the same problem the driver is detected by the additional propriety drivers wizard and after installation , ubuntu can't see except on wireless network which is not mine (and i can't connect to it as it is secured) there are plenty of wireless networks around me but ubuntu can't detect them and if i tried to connect to one of them as if it was hidden connection time out. the command lspci -nvn | grep -i net gives 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) iwconfig gives lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off i guess it is something related to Broadcom driver .. but i don't know , any help will be appreciated UPDATE: ok i installed a new copy of 11.10 to remove the effect of any trials i have made i followed the link (http://askubuntu.com/q/67806) as suggested all what i have done now is trying the command lsmod | grep brc and it gave me the following brcmsmac 631693 0 brcmutil 17837 1 brcmsmac mac80211 310872 1 brcmsmac cfg80211 199587 2 brcmsmac,mac80211 crc_ccitt 12667 1 brcmsmac then i blacklisted all the other drivers as mentioned in the link the wireless is still disabled.. in the last installation installing the Brodcom STA driver form the additional drivers enabled the menu but as i have said before it wasn't able to connect or even get a list of available networks so what should i do now ? the output of command rfkill list all rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Vim: :silent with makeprg

  - by ash

  I use pylint on .py files for :make in my .vimrc, although any program, pylint or otherwise, applies to this problem. set makeprg=pylint\ --reports=n\ --output-format=parseable\ % When I run :make, I inevitably get the annoying Press ENTER or type command to continue prompt. I know this can be disabled with :silent, but I can't prepend it to the makeprg variable like this, because it throws an error: set makeprg=:silent "pylint\ --reports=n\ --output-format=parseable\ %" If I try to have my own "Silent make command," command Smake silent make The screen goes black after calling it. How would I do it?

  Read the article

• Writing a "Hello World" Device Driver for kernel 2.6 using Eclipse

  - by Isaac

  Goal I am trying to write a simple device driver on Ubuntu. I want to do this using Eclipse (or a better IDE that is suitable for driver programming). Here is the code: #include <linux/module.h> static int __init hello_world( void ) { printk( "hello world!\n" ); return 0; } static void __exit goodbye_world( void ) { printk( "goodbye world!\n" ); } module_init( hello_world ); module_exit( goodbye_world ); My effort After some research, I decided to use Eclipse CTD for developing the driver (while I am still not sure if it supports multi-threading debugging tools). So I: Installed Ubuntu 11.04 desktop x86 on a VMWare virtual machine, Installed eclipse-cdt and linux-headers-2.6.38-8 using Synaptic Package Manager, Created a C Project named TestDriver1 and copy-pasted above code to it, Changed the default build command, make, to the following customized build command: make -C /lib/modules/2.6.38-8-generic/build M=/home/isaac/workspace/TestDriver1 The problem I get an error when I try to build this project using eclipse. Here is the log for the build: **** Build of configuration Debug for project TestDriver1 **** make -C /lib/modules/2.6.38-8-generic/build M=/home/isaac/workspace/TestDriver1 all make: Entering directory '/usr/src/linux-headers-2.6.38-8-generic' make: *** No rule to make target vmlinux', needed byall'. Stop. make: Leaving directory '/usr/src/linux-headers-2.6.38-8-generic' Interestingly, I get no error when I use shell instead of eclipse to build this project. To use shell, I just create a Makefile containing obj-m += TestDriver1.o and use the above make command to build. So, something must be wrong with the eclipse Makefile. Maybe it is looking for the vmlinux architecture (?) or something while current architecture is x86. Maybe it's because of VMWare? As I understood, eclipse creates the makefiles automatically and modifying it manually would cause errors in the future OR make managing makefile difficult. So, how can I compile this project on eclipse?

  Read the article

• I cannot access my mongodb from internet ,Anybody can help me?

  - by VicoWu110

  I am using Mongodb database ,which is installed in my ubuntu with the ip address 126.22.252.25. The ubuntu version info is Ubuntu 12.04.3 LTS. My mongodb use the default 27017 port .On this local machine , I can use command "mongo --host 126.22.252.25" on the local machine to access, but I cannot use this command on any other linux mathine to access the db,nor can I use "telnet 126.22.252.25 27017" on my windows machine.I am sure 126.22.252.25 machine is accessable from internet because I can use winSCP and secureCRT to login to it.I run command "netstat -tnlp" , it shows below: tcp 0 0 0.0.0.0:27017 0.0.0.0:* LISTEN I have already change the /ect/mongodb.conf file , modifying bind_ip parameter from 0.0.0.0 to 126.22.252.25 So ,anyone can help me?

  Read the article

• Proper way to remove an active / inactive LVM snapshot

  - by user2622247

  I have created a sample ruby script file for removing extra LVM snapshots from the system. For removing LVM snapshot, we are using lvremove command. This command is working fine and we can remove snapshots from the system. # sudo lvremove /dev/ops/dbbackup lvremove -- do you really want to remove "/dev/ops/dbbackup"? [y/n]: y Sometimes while removing snapshots we are getting following errors. Unable to deactivate open rootfs_12.10_20140812_00-cow (252:8) Failed to resume rootfs_12.10_20140812_00. libdevmapper exiting with 7 device(s) still suspended. The system gets frozen. We cannot fire any command or can not perform any action on it. After restarting the system, it is functioning fine. We can perform all the operations even we can delete that snapshot also. I searched about it I found these threads https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=659762 and https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=674682 Solution from this thread is after getting the error but I have to avoid this type of error. I have a question, Is there any better way removing LVM snapshots? So that we can avoid this type of error. If anyone needs more info feel free to ask me.

  Read the article

• NTP service, offset increasing after sync

  - by Ajay

  I have installed Ubuntu 12.10 version on my PC. I am running NTP service having NTP server as GPS. I found that when we start NTP service by ntp start command, PC is able to sync with GPS as i get '*' symbol before GPS IP when i run ntpq -p command. This remains good for some time and then the * symbol is removed which means that PC is not synchronized to that server. Now, by running command ntpq -p it shows that all parameter are OK but as '*' is removed, slowly offset goes on increasing. remote refid st t when poll reach delay offset jitter ============================================================================== *192.168.100.33 .GPS. 1 u 7 16 1 2.333 23.799 0.808 remote refid st t when poll reach delay offset jitter ============================================================================== *192.168.100.33 .GPS. 1 u 14 16 3 2.333 23.799 0.879 remote refid st t when poll reach delay offset jitter ============================================================================== *192.168.100.33 .GPS. 1 u 11 16 7 2.333 23.799 1.500 remote refid st t when poll reach delay offset jitter ============================================================================== *192.168.100.33 .GPS. 1 u 8 16 17 2.333 23.799 2.177 below are the last 4 ntp status when sync is lost with GPS ============================================================================== 192.168.100.33 .GPS. 1 u 1 16 377 2.404 1169.94 1.735 remote refid st t when poll reach delay offset jitter ============================================================================== 192.168.100.33 .GPS. 1 u - 16 377 2.513 1171.80 0.898 remote refid st t when poll reach delay offset jitter ============================================================================== 192.168.100.33 .GPS. 1 u 15 16 377 2.513 1171.80 0.898 Since, GPS is already available, PC never re-synchronize itself to GPS later ON. I have to restart the ntp service and then PC synchronizes to GPS and '*' symbol arrives.

  Read the article

• Cannot format SD memory card

  - by cool

  Hello everyone I have a SD memory card which is of local manufacturer it allows to read & copy from it but not write as it is now write-protected so i want to format that card but could not. To format this card I have tried 1) DD command 2) mkfs -f vfat command 3) creating registry entry under storage device policy in window with write value 0 4) disk part command in window to clear attributes in which it show all attributes are clear ie no write protection 5) I format card in windows through control panel - administrative tools- computer management - disk management, then it show as formatted but when I tried to create new partition it give CYCLIC REDUNDANCY CHECK error 6) I downloaded a format utility from transcend site and formatted first it shows write protected again doing format it formats and tells to remove and reinsert after reinsertion it shows the previous data as it is

  Read the article

• FIX: Visual Studio Post Build Event Returns &ndash;1 when it should not.

  - by ChrisD

  I had written a Console Application that I run as part of my post build for other projects..  The Console application logs a series of messages to the console as it executes.  I use the Environment.ExitCode value to specify an error or success condition.  When the application executes without issue, the ExitCode is 0, when there is a problem its –1. As part of my logging, I log the value of the exit code right before the application terminates.  When I run this executable from the command line, it behaves as it should; error scenarios return –1 and success scenarios return 0.   When I run the same command line as part of the post-build event, Visual Studio reports the exit code as –1, even when the application reports the exit code as 0.   A snippet of the build output follows: Verbose: Exiting with ExitCode=0 C:\Windows\Microsoft.NET\Framework\v3.5\Microsoft.Common.targets(3397,13): error MSB3073: The command ""MGC.exe" "-TargetPath=C:\TFS\Solutions\Research\Source\Framework\Services\Identity\STS\_STSBuilder\bin\Debug\_STSBuilder.dll" C:\Windows\Microsoft.NET\Framework\v3.5\Microsoft.Common.targets(3397,13): error MSB3073:  C:\Windows\Microsoft.NET\Framework\v3.5\Microsoft.Common.targets(3397,13): error MSB3073: " exited with code -1. The Application returns a 0 exit code.  But visual studio is reporting an error.  Why? The answer is in the way I format my log messages.  Apparently Visual Studio watches the messages that get streamed to the the output console.  If those messages match a pattern used by visual studio to communicate errors, Visual Studio assumes an error has occurred in the executable and returns a –1.  This post details the formats used by Visual Studio to determine error conditions. In my case, the presence of the colon was tripping up Visual studio.  I Replaced all occurrences of colon with an equal sign and Visual Studio once again respected the exit code of the application. Verbose= Exiting with ExitCode=0 ========== Build: 3 succeeded or up-to-date, 0 failed, 0 skipped ==========

  Read the article

• Synaptic won't launch from menu in panel in fresh Lubuntu minimal desktop 12.04 install

  - by ven42

  I performed a fresh install of Lubuntu 12.04 with minimal desktop, as described here: https://help.ubuntu.com/community/Lubuntu/Documentation/MinimalInstall. To clarify, I did a command-line install from the Lubuntu alternative install disc, then I did an "apt-get install --no-install-recommends lubuntu-desktop". Everything is working fine, except that Synaptic will not run from the menu entry in the panel. I am not prompted for a password, and no window of any sort appears after clicking the menu entry. I installed lxshortcut to see what the shortcut was running, and the command is "synaptic-pkexec". If I type this command into the "Run" menu, I get the same behavior (or lack thereof). I can get Synaptic to open up just fine by typing "gksudo synaptic" at the "Run" menu. Also, if I run "synaptic-pkexec" from the terminal, then I am prompted for my password within the terminal, and after that Synaptic opens normally. Can someone please suggest the right way to get Synaptic working? I could just change the menu entry to "gksudo synaptic", but I'm guessing that it's set to "synaptic-pkexec" for a reason. I have a vague understanding that this pkexec business has something to do with PolicyKit, but I don't really know what PolicyKit is or how to tell if something is broken with it. Thanks.

  Read the article

• Handling DataGrid.SelectedItems in an MVVM-friendly manner

  - by Laurent Bugnion

  An interesting question from one of the MVVM Light users today: Is there an MVVM-friendly way to get a DataGrid’s SelectedItems into the ViewModel? The issue there is as old as the DataGrid (that’s not very old but still): SelectedItem (singular) is a DependencyProperty and can be databound to a property in the ViewModel. SelectedItems (plural) is not a DependencyProperty. Thankfully the answer is very simple: Use EventToCommand to call a Command in the ViewModel, and pass the SelectedItems collection as parameter. For example, if the command in the ViewModel is declared as follows:public RelayCommand<IList> SelectionChangedCommand { get; private set; }and (in the MainViewModel constructor):SelectionChangedCommand = new RelayCommand<IList>( items => { if (items == null) { NumberOfItemsSelected = 0; return; } NumberOfItemsSelected = items.Count; }); Then the XAML markup becomes:<sdk:DataGrid x:Name="MyDataGrid" ItemsSource="{Binding Items}"> <i:Interaction.Triggers> <i:EventTrigger EventName="SelectionChanged"> <cmd:EventToCommand Command="{Binding SelectionChangedCommand}" CommandParameter="{Binding SelectedItems, ElementName=MyDataGrid}" /> </i:EventTrigger> </i:Interaction.Triggers> </sdk:DataGrid> I slapped a quick sample and published it here (VS2010, SL4 but the concept works in SL3 and WPF too). Cheers! Laurent Laurent Bugnion (GalaSoft) Subscribe | Twitter | Facebook | Flickr | LinkedIn

  Read the article

• How to install NPM behind authentication proxy on Windows?

  - by Tobias

  I need to run the latest version of Node and NPM on Windows. I installed Node 0.5.8 and downloaded the sources of NPM from GitHub. The steps I followed to install NPM were listed on its GitHub site but I have a problem running the following command: node cli.js install npm -gf but it fails with the following error message: Error: connect UNKNOWN at errnoException (net_uv.js:566:11) at Object.afterConnect [as oncomplete] (net_uv.js:557:18) System Windows_NT 5.1.2600 command "...\\Node\\bin\\node.exe" "...\\npm\\cli.js" "install" "npm" "-gf" cwd ...\npm node -v v0.5.8 npm -v 1.0.94 code UNKNOWN I think that this is a problem because I need authentication at my proxy to connect to the Internet. But I found no way to tell the installer to use my credentials for login. Is there a possibility to provide my proxy IP and login information to npm installation maybe via command-line arguments? I can provide the full log (but seems to have no more relevant information) using pastebin if needed.

  Read the article

• How to stop a infinite running process(ztail) started by a ssh session after that session is closed

  - by Sanath Adiga

  I have a peculiar problem. My server supports multiple ssh session simultaneously, so that multiple admins can manage it simultaneously. We have a command which calls ztail to show the compressed log files and when the current ssh session is closed (without pressing ctrlc, to stop the tail command), the command should ideally stop working. But what I observed when I start a new ssh session is that the process ztail is still running in the background and consuming CPU, even though the previous session was closed. How can I determine when the session is closed, so that I can use that variable/flag to close/stop any commands initiated by that previously closed session?

  Read the article

• wired connection not working in ubuntu 12.04 on lenovo G580 laptop

  - by shravankumar

  I found solution in http://www.zyxware.com/articles/2680/solved-wired-connection-eth0-not-detected-in-ubuntu-12-04 I downloaded compact-wireless-2012-07-03-p.tar.bz2 Here the steps i followed along with output 1. shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ scripts/driver-select alx Output: Processing new driver-select request... Backup exists: Makefile.bk Backup exists: Makefile.bk Backup exists: drivers/net/ethernet/broadcom/Makefile.bk Backup exists: drivers/net/ethernet/atheros/Makefile.bk Backup exists: Makefile.bk Backup exists: Makefile.bk Backup exists: drivers/net/ethernet/broadcom/Makefile.bk 2.shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ make output: make -C /lib/modules/3.2.0-23-generic/build M=/home/shravankumar/Desktop/compat-wireless-2012-07-03-p modules make[1]: Entering directory `/usr/src/linux-headers-3.2.0-23-generic' scripts/Makefile.build:44: /home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx/Makefile: No such file or directory make[4]: *** No rule to make target `/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx/Makefile'. Stop. make[3]: *** [/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx] Error 2 make[2]: *** [/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros] Error 2 make[1]: *** [_module_/home/shravankumar/Desktop/compat-wireless-2012-07-03-p] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.2.0-23-generic' make: *** [modules] Error 2 3. hravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ make install output: FATAL: Could not open /lib/modules/3.2.0-23-generic/modules.dep.temp for writing: Permission denied make: *** [uninstall] Error 1 4. shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ modeprobe alx output: No command 'modeprobe' found, did you mean: Command 'modprobe' from package 'module-init-tools' (main) modeprobe: command not found I am new to Ubuntu ,Please help me. Thanks in advance

  Read the article

• Implementing dry-run in bash scripts

  - by Apikot

  How would one implement a dry-run option in a bash script? I can think of either wrapping every single command in an if and echoing out the command instead of running it if the script is running with dry-run. Another way would be to define a function and then passing each command call through that function. Something like: function _run () { if [[ "$DRY_RUN" ]]; then echo $@ else $@ fi } _run mv /tmp/file /tmp/file2 DRY_RUN=true _run mv /tmp/file /tmp/file2 Is this just wrong and there is a much better way of doing it?

  Read the article

• Running 'sudo' over SSH

  - by Wesho

  I'm writing a script which is to log onto a bunch of remote machines and run a command on them. I've set up keys so the user running the script does not have to type the password of each machine, but only type in the passphrase in the beginning of the script. The problem is that the command on the remote machines requires sudo to run. And at the same time the whole point of the script is to rid the user of having to type in passwords multiple times. Is there way to avoid typing in the password for sudo? Changing permissions of the command on the remote machines is not an option.

  Read the article

• Where is the Flash in Chrome?

  - by Daniel

  I installed Google Chrome. This is the first thing I did after installing Ubuntu. I went into firefox, and went to chrome.google.com, and hit the button. I don't like package managers, and avoid the command line like the pox. Then, I started using Google Chrome. I went to Kongregate, and clicked on a game. It told me I didn't have flash. A few different websites told me the same. I assumed that they must have been wrong. I hit the link to Adobe, to install Flash, and it reassured me; of course, Google Chrome includes Flash. I checked my version - Chrome 5.0.375.126. Of course, I just downloaded it. I scoured the internet for solutions. None worked. Many seemed to involve re-enabling Flash, or something like that. But insofar as I can tell, there is no Flash anywhere in my Chrome. I feel like I bought a Reese's cup, and found solid chocolate. I checked in the Chrome plugin manager, and everything. A few solutions told me to copy some garbage into my command line and hit enter (as almost all solutions to problems on linux entail). I did it, reluctantly, and it did nothing. I thought Flash was supposed to come with Chrome. But it didn't. Sooooo... What gives? Google Chrome version: Google Chrome 5.0.375.126 (Official Build 53802) WebKit 533.4 V8 2.1.10.15 User Agent Mozilla/5.0 (X11; U; Linux x86_64; en-US) AppleWebKit/533.4 (KHTML, like Gecko) Chrome/5.0.375.126 Safari/533.4 Command Line /opt/google/chrome/google-chrome Operating System: Ubuntu 10.4 64 bit.

  Read the article

• Encrypting a non-linux partition with LUKS.

  - by linuxn00b

  I have a non-Linux partition I want to encrypt with LUKS. The goal is to be able to store it by itself on a device without Linux and access it from the device when needed with an Ubuntu Live CD. I know LUKS can't encrypt partitions in place, so I created another, unformatted partition of the EXACT same size (using GParted's "Round to MiB" option) and ran this command: sudo cryptsetup luksFormat /dev/xxx Where xxx is the partition's device name. Then I typed in my new passphrase and confirmed it. Oddly, the command exited immediately after, so I guess it doesn't encrypt the entire partition right away? Anyway, then I ran this command: sudo cryptsetup luksOpen /dev/xxx xxx Then I tried copying the contents of the existing partition (call it yyy) to the encrypted one like this: sudo dd if=/dev/yyy of=/dev/mapper/xxx bs=1MB and it ran for a while, but exited with this: dd: writing `/dev/mapper/xxx': No space left on device just before writing the last MB. I take this to mean the contents of yyy was truncated when it was copied to xxx, because I have dd'd it before, and whenever I have dd'd to a partition of the exact same size, I never get that error. (and fdisk reports they are the same size in blocks). After a little Googling I discovered all luksFormat'ted partitions have a custom header followed by the encrypted contents. So it appears I need to create a partition exactly the size of the old one + however many bytes a LUKS header is. What size should the destination partition be, no. 1, and no. 2, am I even on the right track here? UPDATE I found this in the LUKS FAQ: I think this is overly complicated. Is there an alternative? Yes, you can use plain dm-crypt. It does not allow multiple passphrases, but on the plus side, it has zero on disk description and if you overwrite some part of a plain dm-crypt partition, exactly the overwritten parts are lost (rounded up to sector borders). So perhaps I shouldn't be using LUKS at all?

  Read the article

• Troubleshoot broken ZFS

  - by BBK

  I have one zpool called tank in RaidZ1 with 5x1TB SATA HDDs. I'm using Ubuntu Server 11.10 Oneric, kernel 3.0.0-15-server. Installed ZFS from ppa also I'm using zfs-auto-snapshot. The ZFS file system when zfs module loaded to the kernel hangs my computer. Before it I created few new file systems: zfs create -V 10G tank/iscsi1 zfs create -V 10G tank/iscsi2 zfs create -V 10G tank/iscsi3 I shared them through iSCSI by /dev/tank/iscsiX path. And my computer started to hanging sometimes when I used tank/iscsiX by iSCSI, do not know why exactly. I switched off iSCSI and started to remove this file systems: zfs destroy tank/iscsi3 I'm also using zfs-auto-snapshot so I had snapshots and without -r key my command not destroying the FS. So I issued next command: zfs destroy tank/iscsi3 -r The tank/iscsi3 FS was clean and contain nothing - it was destroyed without an issue. But tank/iscsi2 and tank/iscsi1 contained a lot of information. I tried zfs destroy tank/iscsi2 -r After some time my computer hang out. I rebooted computer. It didn't boot very fast, HDDs starts working like a crazy making a lot of noise, after 15 minutes HDDs stopped go crazy and OS booted at last. All seems to be ok - tank/iscsi2 was destroyed. After file systems at the tank was accessible, zpool status showed no corruption. I issued new command: zfs destroy tank/iscsi1 -r Situation was repeated - after some time my computer hang out. But this time ZFS seams not to healed itself. After computer switched on it started to work: loading scripts and kernel modules, after zfs starting to work it hanging my computer. I need to recover else ZFS file systems which lying in the same zpool. Few month ago I backup OS to flash drive. Booting from backed-up OS and import have the same results - OS starts hanging. How to recover my data at ZFS tank?

  Read the article

• define software path

  - by shantanuo

  I have an older version already installed. I have upraded the package using setup.py install command. But the path is not correctly set. When I type "s3cmd" is shows the older version of software. # s3cmd s3cmd [options] <command> [arg(s)] version 1.2.6 --help -h --verbose -v --dryrun -n # which s3cmd /usr/local/bin/s3cmd The correct version is in different folder and I will like that to be used whenever I type the command. # /usr/bin/s3cmd Consider using --configure parameter to create one. How do I set path? I have added path to .bash_profile file but it does not work. PATH=$PATH:/usr/bin/s3cmd

  Read the article

• Implementing dry-run in bash scripts

  - by Andrei Serdeliuc

  How would one implement a dry-run option in a bash script? I can think of either wrapping every single command in an if and echoing out the command instead of running it if the script is running with dry-run. Another way would be to define a function and then passing each command call through that function. Something like: function _run () { if [[ "$DRY_RUN" ]]; then echo $@ else $@ fi } `_run mv /tmp/file /tmp/file2` `DRY_RUN=true _run mv /tmp/file /tmp/file2` Is this just wrong and there is a much better way of doing it?

  Read the article

• Powershell overruling Perl binmode?

  - by hippietrail

  I have a Perl script which creates a binary file while scanning a very large text file. It outputs to STDOUT which I redirect in the commandline to a file. To optimize it I'm making changes then seeing how low it takes to run. On Linux for this I use the "time" command. On Windows the best way to time a program seemed to be to PowerShell's "measure-command". This seemed to work fine but I noticed the generated files were larger. On examination I found that the files generated from within PowerShell begin with a BOM and contain CRLF pairs! My Perl script has a "binmode STDOUT" directive and does work correctly in a normal dosbox. Is this a bug or misfeature in PowerShell or measure-command? Has it affected others creating binary files by means other than Perl? Googling hasn't turned anything up so far. I'm using Perl 5.12, PowerShell v1.0 and Windows XP.

  Read the article

• Hostname Problem On WHM / cPanel Installation

  - by Eray

  My CentOS 5.6 server's hostname was "centos" . And then i change it to my domain : hostname domain.com And i started to installing WHM / cPanel as explained in here : http://etwiki.cpanel.net/twiki/bin/view/AllDocumentation/InstallationGuide/InstallingCpanel It's installed very well. And the i reboot my server. After rebooting, i was execute this command for open WHM's 2087 port : iptables -I RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 2087 -j ACCEPT Now i'm trying to browse domain.com:2087 i'm getting Server (centos) not found .I noticed it's forwarding to my old hostname (centos) . And then execute this command to verify me hostname hostname it's returned "centos" again. I'm not sure, why it's returned to old hostname. (I think it returned to old hostname after rebooting) . I'm changed it one more time : hostname domain.com Finally, now my hostname is domain.com . BUt still i'm getting centos server not found error. This is result of iptables -L command. P.S. : domain.com/cpanel is working

  Read the article

• wmic output well formed xml on remote queries

  - by Mervin

  I want to use the WMI command line tool (wmic) to get information about windows computers on the network and output it as valid xml. However, I can't seem to find the right way to do this as the outputted xml currently contains invalid tokens for which I think I should use the /TRANSLATE:basicxml switch. The command: wmic /NODE:"tech-demo" /IMPLEVEL:Impersonate /USER:MyUser /PASSWORD:MyPassword /PRIVILEGES:DISABLE /AUTHLEVEL:Pkt /AUTHORITY:"ntlmdomain:companydomain.local" PATH Win32_LogicalDisk GET * /FORMAT:rawxml This command runs but returns invalid xml tokens ('<' and '' I think? edit: it appears to fail parsing at ‹) When I add the translate switch I get the message: Can not use credentials for local connections a bit strange that it tries to query the local pc when I add the switch.. Help would be greatly appreciated.

  Read the article

• Why can't I run Compiz?

  - by jasoncruz98

  I installed Ubuntu 11.10 on my laptop. The main reason I switched to Ubuntu is because I wanted to use Compiz. The first thing I did was to go to Additional Drivers and install ATI/AMD Proprietary FGRLX Graphics Driver. There was also another one available, ATI/AMD Proprietary FGRLX Graphics Driver (post-release updates), but I didn't install that one, because it basically meant the same thing to me as the one I already installed. Next, I went to the ubuntuguide.org Oneiric Wiki http://ubuntuguide.org/wiki/Ubuntu:Oneiric#Compiz_Fusion So I followed the instructions there and ran this command in terminal: sudo apt-get install compiz compizconfig-settings-manager compiz-fusion-plugins-main compiz-fusion-plugins-extra emerald librsvg2-common But then, the terminal window said that the package "emerald" could not be found. So, I ran this command instead: sudo apt-get install compiz compizconfig-settings-manager compiz-fusion-plugins-main compiz-fusion-plugins-extra After that, I installed Fusion Icon by running this command: sudo apt-get install fusion-icon I restarted my computer, searched for Compiz Config Settings Manager, and clicked on it. Then, I activated Wobbly Windows. I logged off and logged back on again, but there was no wobbly windows effect. So I tried clicking on Fusion Icon, but it never started. Can someone please tell me what I did wrong here? Because I see everyone seems to be able to run Compiz except me. I really need to start Compiz, or else I think I'm going to uninstall Ubuntu.

  Read the article

• snmpd agent sends duplicate traps

  - by jsnmp

  I am on Ubuntu 10.04.4 LTS, and I cannot upgrade to a higher version. I have installed the snmpd agent (NET-SNMP version 5.4.2.1) with an apt-get install snmpd command. When an event occurs which sends a trap, two traps are sent for each such event instead of one. For example, when I shut down the agent with command /etc/init.d/snmpd stop, two shutdown traps are sent to the destination host. If I then start back up the agent with command /etc/init.d/snmpd start, then two cold start traps are sent to the destination host. Is this a known issue? Is there a fix for this, or is there a configuration change that is needed to prevent the sending of the duplicate trap? These are the contents of the /etc/snmp/snmpd.conf file: rocommunity public authtrapenable 1 trap2sink <trap destination hostname> public These are the contents of the /etc/default/snmpd file: # This file controls the activity of snmpd and snmptrapd # MIB directories. /usr/share/snmp/mibs is the default, but # including it here avoids some strange problems. export MIBDIRS=/usr/share/snmp/mibs # snmpd control (yes means start daemon). SNMPDRUN=yes # snmpd options (use syslog, close stdin/out/err). SNMPDOPTS='-Ls3d -Lf /dev/null -u snmp -p /var/run/snmpd.pid -c /etc/snmp/snmpd.conf' # snmptrapd control (yes means start daemon). As of net-snmp version # 5.0, master agentx support must be enabled in snmpd before snmptrapd # can be run. See snmpd.conf(5) for how to do this. TRAPDRUN=no # snmptrapd options (use syslog). TRAPDOPTS='-Lsd -p /var/run/snmptrapd.pid' # create symlink on Debian legacy location to official RFC path SNMPDCOMPAT=yes

  Read the article

< Previous Page | 223 224 225 226 227 228 229 230 231 232 233 234  | Next Page >