Search Results

Search found 804 results on 33 pages for 'dylan wan'.

Page 23/33 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• 2wire modem to linksys router

  - by Imajica666

  I want to hook a Linksys router to my 2wire modem/router (2701HG-b) to share my Internet connection. I ran from an open port from the 2wire to the WAN port of the Linksys but it will not work. I did this before with my cable modem to a router to my Linksys router. It worked then but not now. I read I can turn the 2 wire into a modem only but I need the 2wire wireless access also. IPCONFIG /ALL sees the 2wire with IP info as well as DHCP server/gateway. Any ideas?

  Read the article

• Why does my wifi fail to stay connected?

  - by Mark0978

  We have 5 different laptops in the house, 1 macbook, 1 Compaq, 3 dells, plus numerous little devices like ipods, squeezeboxs, squeezebox radios and controllers, you name it. All of them connect to and stay connected to the "downstairs" WIFI just fine. But my laptop (the most expensive of the lot) refuses to stay connected, preferring the much weaker and slower signal upstairs. My laptop is running Win7 (64 bit) Ultimate with an Intel 3945ABG WIFI contoller (It's a Dell Precision M6300). The WIFI Access Point is a Cisco WRT54G2 V1 with firmware: Firmware: DD-WRT v24-sp2 (10/10/09) micro Time: 11:11:10 up 42 min, load average: 0.06, 0.01, 0.00 WAN: Disabled

  Read the article

• Setting up wifi router as a switch for Internet Connection Sharing

  - by William C

  Can my laptop with a 3G connection share its Internet via a Wifi router (Dlink DIR-615)? I turned Internet Connection Sharing on and Windows assigned 192.168.137.1 to my laptop's LAN adapter. Do I connect my laptop to the WAN port or to the LAN port of the router? What should I set as my router's IP address? Do I turn DHCP on my router on? Do I assign 192.168.137.x as static addresses on the other computers? If not, what? Is there anything else I need to set on my router? Thank you!

  Read the article

• Fortigate VPN Routing issue

  - by user1571299

  I have 200B Fortigate unit with 2 internet WAN connections. I also have a remote site which I'm connected to via IPSEC VPN through WAN1. This site has only one GW IP address. I'd also like to setup a VPN ontop of WAN2 with that specific site as it's destination. The default route for my end is WAN1. My problem is I cant figure out how to have both tunnels up at the same time. What's the best practice for achieving this? Thanks

  Read the article

• VPN is working, except for DNS lookups. Firewall (Cisco ASA 5505) issue?

  - by macke

  I've got the following set up: LAN -> DHCP / DNS / VPN server (OSX 10.6) -> Cisco ASA 5505 -> WAN Connecting to the LAN via VPN works fine. I get all the details properly and I can ping any host on the internal network using their IP. However, I can't do any host lookups whatsoever. I've looked through the logs on and found this nugget in the firewall log: 3 Sep 08 2010 10:46:40 305006 10.0.0.197 65371 portmap translation creation failed for udp src inside:myhostname.local/53 dst inside:10.0.0.197/65371 Port 53 is dns services, no? Because of that log entry, I'm thinking that the issue is with the firewall, not the server. Any ideas? Please keep in mind that I have very little knowledge and experience with this kind of firewall and the little experience I do have is with the ASDM GUI console, not the CLI console.

  Read the article

• Access my router's gateway network?

  - by Danpe

  I have 2 routers in my place. Main Router (Connected to the Internet) - 192.168.1.1 Secondery Router (Connected to the Main Router) - 192.168.0.1 I have a Network Storage Device and few Shared Directorys connected to the Main Router. (Network Storage - 192.168.1.16) How can i acces one of them using a PC connected to the Secondery Router? Home Network Diagram: I currently have access to the internet using both laptop and Main PC. But i want to get access from my laptop to the Storage and to ym shared directorys. The problem is the my Main router always forwards all packets stright to the WAN.. (Internet)

  Read the article

• setup advanced filtering and access restrictions on dd-wrt using iptables

  - by Nova deViator

  I have a linksys WRT54GL router with a DD-WRT installed and I want to setup some advanced filtering that seem to not be available through "Access restrictions" web gui option. I guess I would be using IPTABLES then. I have ssh access to router and can run iptables, but I'm not so experienced with iptables. So here are my needs: my policy would be deny all first and then allow exceptions allow all http (port 80) access to WAN through wireless allow all other traffic only to PCs with specific MAC addresses allow internet access to PC with specific MAC address according to schedule (let's say everyday between 18:00-21:00) is this possible to setup with IPtables? could somebody help me a bit with it? or should go and RTFM?

  Read the article

• Can I ping via an arbitrary interface of a DD-WRT system? [migrated]

  - by bytebuster

  There's a Linksys WRT54GL router with DD-WRT firmware (v23SP2). The network has a simple dual-WAN configuration (standby mode, switching by a script): ~ # ip route 192.168.3.0/24 dev br0 proto kernel scope link src 192.168.3.1 192.168.2.0/24 dev vlan2 proto kernel scope link src 192.168.2.2 192.168.1.0/24 dev vlan1 proto kernel scope link src 192.168.1.67 127.0.0.0/8 dev lo scope link default via 192.168.2.1 dev vlan2 I'm trying to ping a certain server arbitrary via vlan1 or vlan2. What I tried, as suggested here: ping -I vlan2 <address> ping 192.168.2.1 <address> In both cases ping simply exits with no error messages. Also, ping ignores many other parameters, again, by exiting silently. I failed to find any references that DD-WRT has a limited version of ping whatsoever. I also don't think it can be a permissions issue as mentioned here since the only user with DD-WRT is root. What's wrong?

  Read the article

• I need to somehow change my ip address

  - by tric

  hello. i`m in a lan using iptables/masquerade. what i want to do, is to login in a web application.i write my user and passwd and click login and everything is fine, but if i try to modify something in that aplication it tells me that i have a wrong ip address.i knwo for sure that this app only allows ip 10.3.x.x .how can i trick that application to think that i have an ip from class 10.3.x.x and not my wan ip? 10x sorry for my bad english!

  Read the article

• Very slow loading pages with router

  - by user984621

  I bought new router - this one: http://www.tp-link.com/en/products/details/?model=TL-WR841ND and the problem is, that the loading pages is so slow, even sometimes the pages aren't loaded at all. Is the same, when I have on the Mac OS or Windows. Below are the informations from the router-admin section: LAN IP Address: 192.168.2.1 Subnet Mask: 255.255.255.0 WAN IP Address: 192.168.1.100 Dynamic IP Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.254 DNS Server: 89.203.178.2 , 10.14.2.1 How can I fix this problem? Is almost impossible to use the internet this way.

  Read the article

• How a router decides destination of packet?

  - by user58859

  I have basic networking question. Scenario : Two pc's are communicating on a wan. Both the pc's ate behind routers or modems. My question : Both the pc's have public IP of each other. That public IP is most of the time is either of the router or of the modem. There can be more then one pc's behind those routers and modems. Then how the pc's are communicating. I can understand the packets can reach upto those routers or modems. But what after that. In the packet , destination IP is public IP. Then how the router or modem decides where to send the packet? Can anybody explain me this please. Thanks in advance.

  Read the article

• how long does noip ddns takes to make the updated address again accessible?

  - by neoDev

  Yesterday I've created a noip account, I've downloaded the updater client (DUC), I've configured them, and when I've tryied to browse "myaddress.noip.me" all worked fine... When my WAN IP changes, the DUC client quickly updates it in few minutes, and in my account on noip.com I can see that it is also refreshed properly. But the problem is that if I try to browse "myaddress.noip.me" after that update, the page does not load... "Unable to connect to myaddress.noip.me" After 6-7 hours it becomes again accessible, but I'm not sure if this is normal... I think this is too much time... Please help

  Read the article

• Two routers on the same network

  - by qroberts

  My ISP has supplied me with a modem/router all in one and it isn't very good. It loses its settings and dies frequently. So I have another router in my apartment (Linksys wrt310n) that is connected to the modem via LAN-LAN port connections. I want to give my Linksys router the DHCP role and also have the ISP modem DMZ everything to the Linksys router. I want to be able to have all computers connected to both routers on the same network as well. I have been able to make it so that the Linksys has a DMZ to it from the ISP modem, but ISP modem LAN port - Linksys WAN port, so they were on different networks. Is there a way to have it so that both of them are on the same network but the Linksys router handles DHCP and port forwarding?

  Read the article

• Remote connection to dynamic public ip & private ip addresses

  - by user51737

  Many times I connected to windows computer which has static public ip address via remote desktop over wan links. I'm wondering how could I connect to the remote computer that has dynamic public ip address & private ip addresses assigned. I've 2 systems at home: xp system-------connected to internet(dynamic public ip) & allowed other users to connected to the internet on the interface. windows vista system--------enabled dhcp on the interface to access internet from xp. How could I remotely connect from my office to the 'vista system'?. If I've a router/modem at my home it may be possible to allow the ports for the system but I don't. Any tips?

  Read the article

• Ubuntu Server 12.04 as a router. Problem with DNS?? Or Routing table?

  - by Lorenzo

  I have a virtualbox lab made up of 4 Windows 2008 R2 servers (DC/DNS,SQL,SHAREPOINT, EXCHANGE) that are configured with static ip addresses with NIC's attached to Internal network. Everything works. I had the requirement to execute some tests that also access external services available on the internet. To keep things clean and similar to the production environment I have installed another VM, with Ubuntu Server 12.04 64 bit and configured (I hope) to work as a router like described on this post. This VM has two network interfaces: first is Bridged with the host and is used as a WAN connection and the other one attached in the Internal Network with its own static IP address on the internal network subnet. But actually the Windows servers does not connect to the internet while the unix one connects. I did a route command. this is the result: Kernel IP Routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.69.121.1 0.0.0.0 UG 100 0 0 eth0 10.69.121.0 * 255.255.255.0 U 0 0 0 eth0 192.168.83.0 * 255.255.255.0 U 0 0 0 eth1 Can somebody help me with this configuration? :) Thanks! Addendum: I forgot to mention that one of the windows server hosts a DNS service for which I should maybe configure a forwarding server but I do not exactly know which server to forward on... :(

  Read the article

• Rate of UDP packet loss over WLAN

  - by Martin

  While testing something with TFTP I noticed lots of timeouts (and slow speed as result) when I used my WLAN - and no problems when using a network cable. A quick test program sending/receiving UDP revealed that there are about 3-5% packets lost. While it's obvious that WLAN has to be less reliable than LAN, I have no knowledge what loss rates are considered 'normal' - and when there is a need to further investigate the network infrastructure. Are there 'typical' packet loss rates on WLAN (and other network technologies e.g. PowerLAN, WAN, ...? Thanks

  Read the article

• Update a DNS to a for a dynamic IP

  - by zobgib

  I want to use my schools connection as a place to host a small webserver but one problem I have run into is anytime my server reboots I am given a new IP inside the schools range. All of the schools IP are public and therefor I can access my computer directly over WAN just via the IP given in ifconfig. I would like to be able to give my computer a dns which is easy enough when I change the Arecords to match the current IP of my computer. The problem is if my computer ever reboots (my school regularly cycles power at night and over holidays) I am assigned a new IP and have to realize it then update the Arecords This is inconvenient and I figure there must be a better way to keep the DNS records updated either via a script or my own BIND server. That way if there is a power cycle I can still access the server via a Domain Name. If you have any direction to point me in it would be much appreciated. I am running Ubuntu 10.04 if that helps :).

  Read the article

• Ping Flooding in router log

  - by Freeman

  I've had recently a period of repeated disconnections from my router with connection problems. I checked my router log I found several Ping Flooding entries all originating from the IP 69.171.227.232 which turned out to be one of Facebook IPs! I'm wondering what does that means? Can Facebook chat cause such a condition? My router is DLink dir 600 and the condition that devices were disconnected from router, not router from internet.. Connection is WAN And how to solve this router problem?? My wifi clients were about 3-5 at that time..

  Read the article

• Routing connections to passthrough a local machine

  - by xiamx

  Please tell me if what I'm trying to do is feasible. I have a router named "R" which is connected to WAN. R allows adding rules to the routing table. There are numerous of machines connected to the LAN port of R, they all have ip addresses 192.168.1.* assigned with DHCP on R. Among those machines, there's a machine C with ip address 192.168.1.100. I want all traffic of other machines in the subnet to pass-through machine C where some filtering and logging will be done. Is this possible? Is there a name for what I'm trying to do? (so i can do more googling later)

  Read the article

• Multiple subnets behind SonicWall TZ 180

  - by Derek

  We have a SonicWall TZ180 that acts as a VPN endpoint. Right now it has one WAN IP address and a /24 assigned to the LAN interface. Our mail cluster administrator asked if it was possible to add a second private class C behind the VPN. This second subnet would be available to the other network and then we would use address objects and acls to limit access. Is this possible? I read up on PortShield but I don't know if that's what we would need to use because we're pushing all data out of one physical port into a Cisco switch that has VLANs already set up. Addendum: It appears that PortShields will do what I want with only one limitation; it requires a direct 1-1 relationship of portshield to physical port. This would then limit us to 4 PortShields on 1 TZ180. Is there a better solution than this?

  Read the article

• howt setup remote access into computer behind 2 routers?

  - by Steve Wasiura

  I can setup remote access to a pc behind a single router/firewall by using NAT and Port Forwarding, simples! But there is a customer that shares an internet connection with another office, and they are behind a second router firewall. I drawed a picture with my crayons but I can't attach it because I'm a new account on SF. see it here: http://i.imgur.com/b3FDx.png So how would I setup remote access to the pc that is beind the second firewall? It must be something about static routes, i.e. if I hit the wan ip on port 4905 I want it to forward it to 10.0.0.30 by going through 192.168.1.10 so a route statement like for all requests to 10.0.0.30, use 192.168.1.10 ? and ass u me router 2 has a static gateway ip of 192.168.1.10 and need a standard NAT on router 2 to point port 4905 to 10.0.0.30 is this the right way, any tips? both routers are netgear consumer equipment. thanks

  Read the article

• Redirect traffic to local address so iOS speedtest app measures LAN speed

  - by ivan_sig

  I have mounted a Speedtest Mini server on a local LAMP, so I can test my LAN speeds effortlessly just by opening the URL with a Flash enabled web browser, the thing is, I want my iOS and Android devices to test with the LAN server too, not with the WAN, as I'm trying to measure LAN-Only performance. Is there a way so I can redirect the traffic intended to an specific external IP (The one of the real server) to my local server?. I know the servers IP as a short Wireshark analysis gave me the data, but still searching for a way to make that redirect. I have Jailbreak and root on my devices, so playing with system files is not a problem. I've tried mounting a proxy and making redirects by the hosts file and domain names, but it looks like Ookla's app relies on IP address only.

  Read the article

• Using m0n0wall in a VM for testing.

  - by tombull89

  I'd like to use m0n0wall inside a (VirtualBox) VM to play about with and see what it can do. Ultimately the goal is to have a number of virtual machines connected to a internal virtual network which goes through to the m0n0wall VM, and then the m0n0wall box connected to the internet through NAT or a bridged addaptor on my host machine. I can find out how to set the LAN and WAN addresses, but this seems to be only for using m0n0wall as a router intead of attached to another router. Let's see if I can diagram this: [Virtual Machine]---Internal (VM Only) Network ---[m0n0wall VM]---Bridged/NAT Addaptor---["real" router]---Internet. Can anybody suggest how I should do this or am I thinking m0n0wall isn't meant to be used like this?

  Read the article

• Cisco 1760 T1 Setup

  - by Joseph

  My 1760 has a WIC1-T1 card in Slot 0 and the slot 0 "OK" light is lit. When the router boots it shows that it sees the T1 card. I would like to configure my T1. I received the following details from my ISP: * Removed IP's IP Version: IPv4 Router Interface: edge1.mia1 -- t1-2/1/0:2:13 -- Switch Port: Vlan: WAN Network: 4.59.?.?/30 Level3 Side: 4.59.?.? Customer Side: 4.59.?.? Cust. LAN IPs: 4.59.?.?/27 The problem is that it is not listed under interfaces. I am a noob with IOS, please let me know if you need more details. Thanks.

  Read the article

• NGINX - Two different rails apps under same domain

  - by Murkin

  I have two different Rails (passenger) apps that I wan to host on one server: somehost.com/ <-- App #1 somehost.com/admin <--- App #2 Tried playing with the 'location' directive, but failed to have both operate. Can someone suggest the correct approach ? (I would prefer both to share same environment, only launch from different directories) EDIT: Sample (desired) config Trying to do something like: server { listen 80; server_name myhost.com; rails_env production; passenger_enabled on; location / { root /opt/main_site/public/; } location /dev { root /opt/admin_site/public/; } }

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >