Search Results

Search found 7776 results on 312 pages for 'configure'.

Page 236/312 | < Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >

  • System Center Essentials server running out of disk space due to stored old updates

    - by Ricket
    We have a System Center Essentials (SCE) server to filter updates to our laptops. We've configured it to download the update, and then the laptops get the update from this server; this of course reduces our internet bandwidth and the time it takes for employees to receive the updates, which reduces the complaints we get about how long updates take. However we currently have a total of 2,255 updates stored on the server. SCE gives a breakdown: Updates with installation errors: 29 Updates needed by computers: 280 Updates installed/up-to-date: 0 Updates with no status: 1946 Our little server has 68gb of hard disk space, and the updates are currently taking 32gb and counting. Some of the updates date back to 2003, but we can't figure out a way to delete them to free up space on the server. Right-clicking an update and clicking Uninstall threatens to remove the update from all computers, which is not what we want. Some of the updates even inform us upon viewing: This update has been replaced by a newer update. Before declining this update, it is recommended that you approve the new update first and verify that this update is no longer needed by any computers. How do you prevent your SCE server from filling its hard drive space? Is there a way to configure the server to only keep updates that are still needed? Furthermore, why (in the above breakdown of updates) are there so many updates with "no status" and 0 updates that are "installed/up-to-date"?

    Read the article

  • Problem adding second domain controller to SBS 2008

    - by Quango
    Have an SBS 2008 server in one location, and want to add a backup domain controller at a different site. The two sites are linked by a VPN. New server is running Server 2008 R2, fully patched. At present it is a member server and the DNS is pointing at the SBS DNS. When I try running DCPROMO to connect the server, the wizard runs fine up to the point where the wizard is 'configuring Active Directory Domain Services' and 'examining forest': "The operation failed because: The wizard could not read operational attributes from the remote Active Directory Domain Controller SERVER.DOMAIN.LOCAL using LDAP. "The specified server cannot perform the requested operation." This error can occur if you have not been granted necessary permissions to read data in the directory. For more information, please see article 936241 in the Microsoft Knowledge Base (http://go.microsoft.com/fwlink/?LinkId=88420)." I was logged on as domain administrator. Interestingly the link is invalid and the KB article does not exist..! Settings: Configure this server as an additional Active Directory domain controller for the domain "[domain]". Site: [site] Additional Options: Read-only domain controller: "No" Global catalog: Yes DNS Server: Yes Update DNS Delegation: No Source domain controller: any writable domain controller Database folder: C:\Windows\NTDS Log file folder: C:\Windows\NTDS SYSVOL folder: C:\Windows\SYSVOL The DNS Server service will be configured on this computer. This computer will be configured to use this DNS server as its preferred DNS server.

    Read the article

  • Azure load-balancing strategy

    - by growse
    I'm currently building out a small web deployment using VM instances on MS Azure. The main problem I'm facing at the moment is trying to figure out how to get the load-balancing to detect if a particular VM has failed and not route traffic to that VM. As far as I can tell, there are only only two load-balancing options: Have multiple VMs (web01, web02, web03 etc.) within the same 'cloud service' behind a single VIP, and configure the endpoints to be load balanced. Create multiple 'cloud services', put a single web VM in each and create a traffic manager service across all these services. It appears that (1) is extremely simplistic and doesn't attempt to do any host failure detection. (2) appears to be much more varied, but requires me to put all my webservers in their own individual cloud service. Traffic manager appears to be much more directed at a geographic failover scenario, where you have multiple cloud services across different regions. This approach also has the disadvantage in that my web servers won't be able to communicate with my databases on internal IP addresses, unlike scenario (1). What's the best approach here?

    Read the article

  • How small (spec wise) can a virtual machine be and still boot up and run some sort of OS?

    - by IllvilJa
    One of the advantages with virtual machines is that you can be very flexible with their sizes. If the host system permits it, you can have a very large virtual machine with a lot of virtual RAM and disk. Also, you can decide to go the other way around, to give the virtual machine a very modest amount of RAM and disk and then choose and configure the OS appropriately. The question is, how small virtual machines have people managed to setup (and get to both boot up and to run)? Virtual machines doing something usuful is preferable, even if I know "useful" in this context is awfully subjective, but laboratory-cases with a configuration stripped beyond common sense could be intresting as well, just to see what people manage to boot and run. Quite open ended question and quite academic, but think of it: an extremely small VM (which still does something useful) takes very little memory and disk and can be quite quickly saved to and restored from disk. If it's also gentle on CPU resources, one might consider having a huge number of such VMs up and running on a host. (Imagine a VM running just an old Commodore 64 or Commodore Amiga in it. Ok, way wrong CPU architecture for modern Virtualization software running on a x86-based PC but still an interesting thought. You could have quite a few such small VMs running on a modern PC.)

    Read the article

  • two computers on same network cannot ping eachother nor view NetBios resources

    - by slava
    I'd like to find out the problem of my network configuration I have network configuration is like in this diagram: The problem is between laptop1 and laptop2. At first I thought it was samba server problem. I was configuring samba server on one of the laptops and I wasn't able to access the shares from the second laptop no matter what I was doing. After installing/removing/configuring samba-server a couple of times I realized that the problem resides somewhere else. Laptop configurations: - Laptop1: ubuntu 12.04 - Laptop2: Windows 7/ ubuntu 12.04 ( dual boot ) - Server : ubuntu 12.04 When I do "ping 192.168.0.10" from laptop2, I get "Destination host unreachable". The same situation is when I ping in other direction. When I access Laptop1 shares from Laptop2, having windows 7 loaded, I get the error message: "Error code: 0x80070035 The network path was not found." When I ping "server" or "router" or "wifi router" from any of laptops I get a reply. The same with windows shares, I am able to access "server"s shares from Windows and Ubuntu, from any of my laptops. Netbios can't function correctly, that's obvious, I am unable to access windows shares between laptops. I assume that on "wifi router" is a miss-configuration, but I can't find what specifically. The "Wifi router" works as Hub + wifi, it is connected to "router" not in WAN port but in LAN1. Please, help me correctly configure the router to make them see each-other, or at least make NetBios work correctly, between laptops, to be able to access windows shares. Thanks!

    Read the article

  • Ubuntu Server: Networking fails with MODPROBE option in /etc/network/interfaces ... ??

    - by neezer
    For some reason (which I haven't been able to determine yet), yesterday morning the networking service on our web server (running Ubuntu 8.04.2 LTS -- hardy) wouldn't start, and our website went down. I noticed the following error message when trying to restart it: * Reconfiguring network interfaces... /etc/network/interfaces:6: option with empty value ifup: couldn't read interfaces file "/etc/network/interfaces" ...fail! Line 6 in the /etc/network/interfaces file concerned a MODPROBE command, which (I believe) loaded in the ip_conntrack_ftp module so that I could use PASV on my FTP server (vsftpd): (breaking modprobe commands commented out below) # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or # /usr/share/doc/ifupdown/examples for more information. # The loopback network interface auto lo iface lo inet loopback #MODPROBE=/sbin/modprobe #$MODPROBE ip_conntrack_ftp pre-up iptables-restore < /etc/iptables.up.rules # The primary network interface # Uncomment this and configure after the system has booted for the first time auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask 255.255.255.0 gateway xxx.xxx.xxx.1 dns-nameservers xxx.xxx.xxx.4 xxx.xxx.xxx.5 I've verified that there is a file in /sbin called modprobe. Like I said earlier, this setup had been working flawlessly until yesterday morning (though my bosses say that the site actually went down the previous night at 11 PM EST). Can anyone shed some light on (A) why this broke, and (B) how can I re-enable the ip_conntrack_ftp module?

    Read the article

  • Hardening non-root standalone Linux Tomcat install

    - by NoozNooz42
    I want to know if you have any tips as to how to strengthen the security of a non-root install of Tomcat in standalone mode once Tomcat is already installed in a non-root account, in standalone mode. I precise this because, for example, I'm not at all interested by the answers given here (because both Java and Tomcat requires root priviledges there to be installed and I've got zero interest in running jsvc): http://serverfault.com/questions/43765 So far, here's what I've done for my non-root standalone Tomcat 6 install: download and install the JRE .bin provided by Oracle/Sun (no need to be root here) (no need for a full JDK anymore right seen that Jasper [Tomcat's JSP engine] has its own compiler now right?) download and tar -xzf tomcat 6 (no need to be root here) set up transparent port-forwarding (must be root here) Note that my distribution is a Debian one and I have exactly zero interest in downloading Debian package / backports / whatever... Because, once again, I DO NOT want to need to be root to install Java & Tomcat. The only moment I needed to be root was to configure the firewall to transparently do the port forwarding 80 <-- 8080 and 443 <-- 8443. I then deleted all the default webapps but one: cd ~/apache-tomcat-6.0.26/webapps rm -rf docs rm -rf examples/ rm -rf manager/ rm -rf ROOT/ What about the directory ~/apache-tomcat-6.0.26/webapps/host-manager, do I need it or can I delete it? So, once I've installed Tomcat standalone in a non-root account (and taken into account that I don't want to enter the root password anymore and that I don't plan to install the whole Apache shebang), what more can I do? Are there connectors I can disable? (how?)

    Read the article

  • Apache debugging: where to find error logs?

    - by AP257
    I'm new to Apache and web serving generally, so apologies if this is a very stupid question. I want to configure a new sub-domain on a working site and install a forum there. I'm using a Debian server that already has Apache, mod_wsgi and a bunch of virtual hosts successfully running on it. I first installed my forum app (Django's OSQA). Following the OSQA instructions, I then created an Apache config file that specified ServerName as the new sub-domain. I also created a .wsgi file for the app, and pointed WSGIScriptAlias at it. I then restarted Apache. However, when I go to the new sub-domain, I get a 404 error message. Two questions: Is there a step missing above? Or is simply creating a new Apache config file in sites-available enough to 'tell' Apache about a new sub-domain? If there's something else going wrong, how can I debug it? The ErrorLog and CustomLog specified in the config file are both blank. apache2.conf, which I guess is Apache-wide configuration, specifies ErrorLog /var/log/apache2/error.log, but this is yet another blank file.

    Read the article

  • Need to find jni.h in cmake on Mac

    - by Ilan Tal
    I am trying to make VTK compile on a Mac Air machine. I am using CMake 2.8-9, using Xcode4 as the generator. If I press the Configure button with VTK_WRAP_JAVA not checked, it will go with no errors. However I definitely need to use the wrap java since my main program is in Java and I need to get to VTK which is c++. As soon as I check the wrap Java, I get Could NOT find JNI. It apparently is looking for jni.h which in Linux there is no problem finding, but in the Mac it apparently can't find it. I did a locate jni.h and got new-host-2:~ geraldkolodny$ locate jni.h /Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX10.7.sdk/System/Library/Frameworks/JavaVM.framework/Versions/A/Headers/jni.h /Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX10.8.sdk/System/Library/Frameworks/JavaVM.framework/Versions/A/Headers/jni.h /Library/Java/JavaVirtualMachines/jdk1.7.0_07.jdk/Contents/Home/include/jni.h I tried to manually put into JAVA_INCLUDE_PATH2 either entry 2 or 3 (without the jni.h at the end), but it still can't find jni.h. Xcode used to have a template for jni but that is now gone in the latest version. I am fresh out of ideas on how to solve this problem. I'd be grateful for any suggestions. Thanks, Ilan

    Read the article

  • Samba server NETBIOS name not resolving, WINS support not working

    - by Eric
    When I try to connect to my CentOS 6.2 x86_64 server's samba shares using address \\REPO (NETBIOS name of REPO), it times out and shows an error; if I do so directly via IP, it works fine. Furthermore, my server does not work correctly as a WINS server despite my samba settings being correct for it (see below for details). If I stop the iptables service, things work properly. I'm using this page as a reference for which ports to use: http://www.samba.org/samba/docs/server_security.html Specifically: UDP/137 - used by nmbd UDP/138 - used by nmbd TCP/139 - used by smbd TCP/445 - used by smbd I really really really want to keep the secure iptables design I have below but just fix this particular problem. SMB.CONF [global] netbios name = REPO workgroup = AWESOME security = user encrypt passwords = yes # Use the native linux password database #passdb backend = tdbsam # Be a WINS server wins support = yes # Make this server a master browser local master = yes preferred master = yes os level = 65 # Disable print support load printers = no printing = bsd printcap name = /dev/null disable spoolss = yes # Restrict who can access the shares hosts allow = 127.0.0. 10.1.1. [public] path = /mnt/repo/public create mode = 0640 directory mode = 0750 writable = yes valid users = mangs repoman IPTABLES CONFIGURE SCRIPT # Remove all existing rules iptables -F # Set default chain policies iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP # Allow incoming SSH iptables -A INPUT -i eth0 -p tcp --dport 22222 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22222 -m state --state ESTABLISHED -j ACCEPT # Allow incoming HTTP #iptables -A INPUT -i eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT #iptables -A OUTPUT -o eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT # Allow incoming Samba iptables -A INPUT -i eth0 -p udp --dport 137 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p udp --sport 137 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p udp --dport 138 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p udp --sport 138 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 139 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 139 -m state --state ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 445 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 445 -m state --state ESTABLISHED -j ACCEPT # Make these rules permanent service iptables save service iptables restart**strong text**

    Read the article

  • Multiple IPs on firewall, are these virtual interfaces or what?

    - by Jakobud
    We have 5 static IP addresses from our ISP: XXX.XXX.XXX.180 XXX.XXX.XXX.181 XXX.XXX.XXX.182 XXX.XXX.XXX.183 XXX.XXX.XXX.184 On our firewall box, the NIC that is connected to our cable modem, appears to have all 5 IP addresses set on it. A previous IT guy set this thing up, and I'm not sure exactly what he did. Are these virtual interfaces on this NIC or what? Here is my ip addr output for that NIC: rwd0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff inet XXX.XXX.XXX.180/24 brd XXX.XXX.XXX.186 scope global rwd0 inet XXX.XXX.XXX.181/29 brd XXX.XXX.XXX.186 scope global rwd0:FWB9 inet XXX.XXX.XXX.182/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB10 inet XXX.XXX.XXX.183/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB11 inet XXX.XXX.XXX.184/29 brd XXX.XXX.XXX.186 scope global secondary rwd0:FWB12 inet6 fe80::250:8bff:fe61:5734/64 scope link valid_lft forever preferred_lft forever I'm a bit new to firewalls and networking so I'm just trying to figure out what he had going on here. I know he used Firewall Builder to configure the iptables rules, maybe that has something to do with the "FWB" I see in those names? So my questions are: What is going on here? Virtual Interfaces? Or something else? If we want to put in a second firewall in parallel with this firewall but we only want it to handle traffic to XXX.XXX.XXX.182, how do we get rid of the static XXX.XXX.XXX.182 address on this existing firewall box?

    Read the article

  • Upgrading memory on an IBM Power 710 Express (8231-E2B)

    - by cairnz
    We have a Power 710 Express server that was loaded with 4x4 GB memory on a single riser card. I have replaced the 4 chips with 4x8GB and put in another riser card and loaded it with 4x8GB more for a total of 64GB memory. The firmware is AL730_078. When i power it on, the service processor boots up and i can access the ASMi. From here I can look at "Memory Serial Presence Data" and see that the system in some way detects 8x8 GB. However when i look at Hardware Deconfiguration and specifically Memory Deconfiguration, it is still listed with old values, 16384MB, and claims there are 4x4 chips in the C17 riser. How do i proceed to make the server recognize properly the amount of memory installed? I get a FSPSP04 and B181B50F progress code on booting because (i think) it hasn't been told the memory has changed. It then does not proceed to booting the operating system (VIOS) when turned on. Are there any steps I have overlooked here? Can I do some commands, either on the service processor, or otherwise, to tell the system to configure with the proper amount of memory? PS: This is a stand alone server, not configured with HMC or SDMC.

    Read the article

  • How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • Network config for KVM on physical machine with single NIC and single public IP

    - by neo0
    I have a physical machine running CentOS 6.4 and I will rent a place to run it in a data center. I want to install KVM on that machine to run some virtual machines. The problem is my physical machine have only one NIC and the data center give me a public IP for that interface. So how should I configure network on the physical machine to make it assign for each vm a private IP that can connect to Internet. If I create a br0 bridged with eth0 interface and create a vm with option --bridge=br0 then KVM could not assign an IP for the vm so setup can not be done. Should I use NAT mode? Does KVM have any host-only network like Virtualbox? But the vm still has to connect to outside? Thank you! Update I install the guest network using NAT (--network network:default) and then I only have to port-forwarding from the host. But if I config br0 bridged with physical eth0 then the guest can not get an IP from boot. So I removed the br0 and it worked.

    Read the article

  • If spambots are filling out forms on my website, should I mark the mail as spam?

    - by rob
    Apparently spambots have discovered the contact forms my website. I'm considering adding a CAPTCHA, but in the meantime I've been getting dozens of completed website forms in my Gmail account each day. I know I can configure a filter to always allow e-mails from my website to be delivered (i.e., "never send to spam"), but I'm wondering whether there are also larger implications. At first, I was marking the spam forms as spam because I figured it would block the sender's e-mail address from getting through again. But since then, I've given it some more thought. I know many spam filters use Bayesian filters and other techniques to identify spam based on its content. If I mark all these e-mails as spam, will legitimate e-mails from my website be marked as spam? Even if I stop marking the messages as spam, I can see another potential problem. My form is pretty standard (in fact, it's probably very similar to other online forms). If I mark my spambot-submitted website forms as spam, will Gmail begin to mark other people's similar-looking messages as spam?

    Read the article

  • bind9 dlz/mysql at ubuntu segfault libmysqlclient.so

    - by Theos
    I have a big problem. I installed the bind9 nameserver to three different computer. two Ubuntu 10.04.4 LTS, and one Ubuntu 11.10 I compiled it 9.7.0, 9.7.3, 9.9.0 with this method: ./configure --prefix=/usr --sysconfdir=/etc/bind --localstatedir=/var \ --mandir=/usr/share/man --infodir=/usr/share/info \ --enable-threads --enable-largefile --with-libtool --enable-shared --enable-static \ --with-openssl=/usr --with-gssapi=/usr --with-gnu-ld \ --with-dlz-mysql=yes --with-dlz-bdb=no \ --with-dlz-filesystem=yes --with-geoip=/usr make make install After the set up for dlz/mysql, the BIND server is working perfetctly until 5-30 minute long. Ahter i got segfault. I resolve temporaly the problem with a simple process watchdog, and if the named is stopped, the watchdog is restart it, but this is not a good idea in long therm. My log output is: messages: Apr 13 19:33:51 dnsvm kernel: [ 8.088696] eth0: link up Apr 13 19:33:58 WATCHDOG: named not running. Restarting Apr 13 19:35:08 dnsvm kernel: [ 87.082572] named[1027]: segfault at 88 ip b71c4291 sp b5adfe30 error 4 in libmysqlclient.so.16.0.0[b714e000+1aa000] Apr 13 19:35:08 WATCHDOG: named not running. Restarting Apr 13 19:35:08 dnsvm kernel: [ 87.457510] named[1423]: segfault at 68 ip b71d6122 sp b52f0a40 error 4 in libmysqlclient.so.16.0.0[b7160000+1aa000] Apr 13 19:35:09 WATCHDOG: named not running. Restarting Apr 13 19:41:56 dnsvm kernel: [ 494.838206] named[1448]: segfault at 88 ip b731c291 sp b5436e30 error 4 in libmysqlclient.so.16.0.0[b72a6000+1aa000] Apr 13 19:41:57 WATCHDOG: named not running. Restarting Apr 13 19:57:26 dnsvm kernel: [ 1424.023409] named[2976]: segfault at 88 ip b72d1291 sp b6beee30 error 4 in libmysqlclient.so.16.0.0[b725b000+1aa000] Apr 13 19:57:26 WATCHDOG: named not running. Restarting Apr 13 20:11:56 dnsvm kernel: [ 2294.324663] named[6441]: segfault at 88 ip b7357291 sp b6473e30 error 4 in libmysqlclient.so.16.0.0[b72e1000+1aa000] Apr 13 20:11:57 WATCHDOG: named not running. Restarting syslog: http://pastebin.com/hjUyt8gN the first server is a native, normal x64 server (u1004lts), the second is virtualised server (u11.10) the third is also virtualised (10.04lts) This servers is only for dns providing with mysql server db. But the problem is be with all server, and all bind version. named.conf: http://pastebin.com/zwm1yP7V Can anybody help me, or any good idea?

    Read the article

  • NetApp NDMP backup with BE 2010 R2 works, restore fails

    - by uuwe
    Hi, I'm having some issues with a new Backup Exec 2010 R2 installation. I configured a NetApp FAS2020 as an NDMP device and want to backup files from the NAS to a tape drive connected to my backup server. I set up ndmpd according to this document (http://www.symantec.com/business/support/index?page=content&id=TECH48957) and created a separate backup user (http://filers.blogspot.com/2006/09/setting-veritas-netbackup-with-non.html). Backup works perfectly, but restoring any file gives me an authentication failed error. The NDMP device has a "global" ndmp user configured in the device tab (tried this with the newly created ndmpd backup user and the netapp root) and I can also configure separate resource credentials in the BE restore job. I have tried setting the same accounts for the "global" ndmp device and the restore credentials and have also tried setting different accounts for them. NDMP debug level is at 5 and this is what shows up in /etc/messages. The session is closed immediately after it has been granted. 16:12:07 PST [Java_Thread:info]: ndmpdserver: ndmpd.access allowed for version = 4, sessionId = 51, from src ip = 192.168.11.17, dst ip = FAS2020-1/192.168.11.75, src port = 50857, dst port = 10000 16:12:07 PST [Java_Thread:info]: Ndmpd51: ndmpd session closed successfully for version = 4, sessionId = 51, from src ip = 192.168.11.17, dst ip = FAS2020-1/192.168.11.75, src port = 50857, dst port = 10000 Running wireshark on the backup server doesn't produce much. It shows a SYN - SYN/ACK - NDMP CONNECT_CLOSE Request from the backup server. The Resource Credentials for the restore job behave very oddly. If I enter NDMP credentials and do "Test All" it fails. If I use my regular domain backup account, it is successful. There are no failed or succeeded logons in the NetApp ndmp log and tracing this check shows that it doesn't even connect to the NAS. This makes me think that this is more likely flaky BE behaviour rather than misconfiguration of the NAS. Here is the options ndmp output: FAS2020-1 options ndmp ndmpd.access all ndmpd.authtype challenge ndmpd.connectlog.enabled on ndmpd.enable on ndmpd.ignore_ctime.enabled off ndmpd.offset_map.enable on ndmpd.password_length 16 ndmpd.preferred_interface disable ndmpd.tcpnodelay.enable off

    Read the article

  • Ruby 1.9.3 - Bundler - Graylog2

    - by Arenstar
    im having a strange problem with bundler. Using ruby 1.8 the following works fine however not with 1.9 it always results in Could not find rake-0.9.2.2 in any of the sources Run `bundle install` to install missing gems. i dont understand why, but it functions correctly with rvm. I can not however use rvm, this is not a solution to my problem Install Ruby cd /usr/local/src wget http://ftp.ruby-lang.org/pub/ruby/1.9/ruby-1.9.3-p194.tar.gz tar xzf ruby-1.9.3-p194.tar.gz && cd ruby-1.9.3-p194 ./configure --prefix=/opt/lp/ruby-1.9.3-test make all && make install Install Graylog cd /usr/local/src wget https://github.com/downloads/Graylog2/graylog2-web-interface/graylog2-web-interface-0.9.6p1.tar.gz tar xzf graylog2-web-interface-0.9.6p1.tar.gz cd graylog2-web-interface-0.9.6p1 Setup Graylog cd /usr/local/src/graylog2-web-interface-0.9.6p1 sed -i "3 i gem 'thin', '~> 1.3.1'" Gemfile /opt/lp/ruby-1.9.3-test/bin/gem install bundle /opt/lp/ruby-1.9.3-test/bin/bundle install --path vendor/bundle --binstubs Begin the Test cd /usr/local/src/graylog2-web-interface-0.9.6p1 /opt/lp/ruby-1.9.3/bin/bundle exec bin/rake #Could not find rake-0.9.2.2 in any of the sources #Run `bundle install` to install missing gems. cd /usr/local/src/graylog2-web-interface-0.9.6p1 /opt/lp/ruby-1.9.3/bin/bundle exec bin/thin -e production -S test.sock -c . -R config.ru start #Could not find rake-0.9.2.2 in any of the sources #Run `bundle install` to install missing gems. Where am i going wrong?

    Read the article

  • Pinging an external server through OpenVPN tunnel doesn’t work

    - by qdii
    I have an OpenVPN server and a client, and I want to use this tunnel to access not only 10.0.8.0/24 but the whole internet. So far, pinging the server from the client through the tun0 interface works, and vice versa. However, pinging www.google.com from the client through tun0 doesn’t work (all packets are lost). I figured that I should configure the server so that any packet coming from tun0 in destination of the internet be forwarded, so I came up with this iptables config line: interface_connecting_to_the_internet='eth0' interface_openvpn='tun0' internet_ip_address=`ifconfig "$interface_connecting_to_the_internet" | sed -n s'/.*inet \([0-9.]*\).*/\1/p'` iptables -t nat -A POSTROUTING -o "${interface_connecting_to_the_internet}" -j SNAT --to-source "${internet_ip_address}" echo '1' > /proc/sys/net/ipv4/ip_forward Yet, this doesn’t work, the packets are still lost and I am wondering what could possibly be wrong with my setup. Some details: ip route gives on the server: default via 176.31.127.254 dev eth0 metric 3 10.8.0.0/24 via 10.8.0.2 dev tun0 10.8.0.2 dev tun0 proto kernel scope link src 10.8.0.1 127.0.0.0/8 via 127.0.0.1 dev lo 176.31.127.0/24 dev eth0 proto kernel scope link src 176.31.127.109 ip route gives on the client: default via 192.168.1.1 dev wlan0 proto static 10.8.0.1 via 10.8.0.5 dev tun0 10.8.0.5 dev tun0 proto kernel scope link src 10.8.0.6 127.0.0.0/8 via 127.0.0.1 dev lo scope link 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.109 client uses wifi adapter wlan0 and TUN adapter tun0. server uses ethernet adapter eth0 and TUN adapter tun0. the VPN spans on 10.0.8.0/24 both client and linux are using Linux 3.6.1.

    Read the article

  • Setting up 802.1X wireless connection on OSX

    - by hizki
    I am an OSX user, I have Snow Leopard 10.6.5 and an updated AirPort (version 5.5.2). I am trying to connect to my university's wireless network, but it has a 802.1x security that I am having trouble defining... Here there are instructions for connecting with Windows XP, Windows 7 and Linux. Can someone please instruct me what should I do to set up this network on my Mac? I have had previous success in setting up this network, but I have no idea what I did that made it work. Since I updated my AirPort (to version 5.5.2) it worked only seldomly and very slowly... Before the update, even when it worked it never remembered my password. Update: I have already tried to create a new "location", removed all the 802.1x user profiles and all the remembered networks, and made sure the in the TCP/IP tab 'Configure IPv4' is set to "Using DHCP". I also moved /Library/Preferences/SystemConfiguration/preferences.plist to my desktop in attempt to force the system to create a new set of settings. Still I can define the connection to work.

    Read the article

  • Tell VLC where to look for plugins.dat file

    - by puk
    I am trying to build vlc from source (I will include installation script below), but when I try to run vlc I get the following error main libvlc warning: cannot read /home/user/downloads/vlc3/vlc/src/.libs/vlc/plugins/plugins.dat (No such file or directory) Why is it even looking in that non existant directory? The plugins.dat file is in /usr/lib/vlc/plugins/. I tried export VLC_PLUGIN_PATH=/usr/lib/vlc/plugins/ But it still looks in that non existent path. I can create a symbolic link, but that is a terrible way to do it. If in 6 months I delete my downloads folder, all of a sudden my vlc will break. Here is the script I am running to install: ./configure --enable-rpi-omxil --enable-dvbpsi --enable-x264 --enable-xcb --with-x --enable-xvideo --enable-sdl --enable-avcodec --enable-avformat --enable-swscale --enable-mad --enable-a52 --enable-libmpeg2 --enable-dvdnav --enable-faad --enable-vorbis --enable-ogg --enable-theora --enable-mkv --enable-freetype --enable-fribidi --enable-speex --enable-flac --enable-live555 --enable-caca --enable-skins2 --enable-alsa --enable-ncurses --enable-debug --enable-lirc --enable-live555 --enable-shout --enable-taglib --enable-vcdx --enable-realrtsp --enable-svg --enable-dvdread --enable-dc1394 --enable-twolame --enable-dirac --enable-aa --enable-jack --enable-bluray --enable-opencv --enable-sftp --enable-pulse --enable-projectm --enable-vsxu --enable-atmo --enable-glspectrum '--with-extra-libs=/usr/local/lib' '--with-extra-includes=/usr/local/include' '--x-libraries=/usr/local/lib' '--x-includes=/usr/local/include' '--prefix=/usr/local' '--mandir=/usr/local/man' '--infodir=/usr/local/info/' EDIT: I am using the following version: VLC media player 2.2.0-git Weatherwax (revision 2.1.0-git-1168-g5804dd1) And the --plugin-path option is no longer supported.

    Read the article

  • exim4 to relay emails

    - by Matthieu
    I have exim4 installed on a Linux box. The basics work fine and I can send email from that machine without any problem to whatever email address. I also have a printer/scanner which is capable to send scans as emails. It needs an SMTP gateway to be able to do that. So I give the IP address of that Linux box, changed the configuration a little bit but still cannot get it to work. After I run dpkg-reconfigure exim4-config, here is what I get in /etc/exim4/update-exim4.conf.conf : dc_eximconfig_configtype='internet' dc_other_hostnames='' dc_local_interfaces='127.0.0.1;192.168.2.2' dc_readhost='' dc_relay_domains='mycompanyemail.com' dc_minimaldns='false' dc_relay_nets='192.168.2.0/24' dc_smarthost='' CFILEMODE='644' dc_use_split_config='false' dc_hide_mailname='' dc_mailname_in_oh='true' dc_localdelivery='mail_spool' My problem is that with this configuration, I can only send to emails @mycompanyemail.com... It says I can use wildcard, but when I do that, the '*' is replaced by whatever filename is in the directory where I run all that. How can I configure it to be able to send emails with any domain ? Or am I doing it wrong ? EDIT : here is the part of the log that's causing trouble : 2011-08-03 16:28:18 H=(NPI2D389C) [192.168.2.20] F=<[email protected]> rejected RCPT <[email protected]>: relay not permitted The first part ([email protected]) does not matter. I changed the email address. The point is that if this email is @mycompanyemail.com then everything works fine. Anything else does not work. I could add gmail.com, but I am looking to have any domain working...

    Read the article

  • Basic multicast network performance problems

    - by davedavedave
    I've been using mpong from 29west's mtools package to get some basic idea of multicast latency across various Cisco switches: 1Gb 2960G, 10Gb 4900M and 10Gb Nexus N5548P. The 1Gb is just for comparison. I have the following results for ~400 runs of mpong on each switch (sending 65536 "ping"-like messages to a receiver which then sends back -- all over multicast). Numbers are latencies measured in microseconds. Switch Average StdDev Min Max 2960 (1Gb) 109.68463 0.092816 109.4328 109.9464 4900M (10Gb) 705.52359 1.607976 703.7693 722.1514 NX 5548(10Gb) 58.563774 0.328242 57.77603 59.32207 The result for 4900M is very surprising. I've tried unicast ping and I see the 4900 has ~10us higher latency than the N5548P (average 73us vs 64us). Iperf (with no attempt to tune it) shows both 10Gb switches give me 9.4Gbps line speed. The two machines are connected to the same switch and we're not doing any multicast routing. OS is RHEL 6. 10Gb NICs are HP 10GbE PCI-E G2 Dual-port NICs (I believe they are rebranded Mellanox cards). The 4900 switch is used in a project with tight access control so I'm waiting for approval before I can access it and check the config. The other two I have full access to configure. I've looked at the Cisco document[2] detailing differences between NX-OS and IOS w.r.t multicast so I've got some ideas to try out but this isn't an area where I have much expertise. Does anyone have any idea what I should be looking at once I get access to the switch? [1] http://docwiki.cisco.com/wiki/Cisco_NX-OS/IOS_Multicast_Comparison

    Read the article

< Previous Page | 232 233 234 235 236 237 238 239 240 241 242 243  | Next Page >