Search Results

Search found 9559 results on 383 pages for 'mail rule'.

Page 237/383 | < Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >

  • ISA 2006 refuses VPN DHCP requests as spoofing

    - by Daniel
    I'm running ISA 2006 with PPTP VPN for my AD-controlled network. DHCP is located on the ISA server itself and authentication is done by RADIUS (NPS) located on the DC. Right now my VPN clients can connect, access local DNS, and can ping ISA, the DC, and other clients. Here's where it gets weird. I noticed that despite all this, ipconfig shows the following: PPP adapter North Horizon VPN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : North Horizon VPN Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.42.4.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 0.0.0.0 DNS Servers . . . . . . . . . . . : 10.42.1.10 NetBIOS over Tcpip. . . . . . . . : Enabled So I went over and checked my ISA logs for both DHCP requests and replies, only to find out that my VPN clients are being denied because ISA thinks its a spoof. Here's some relevant information from the log (the VPN subnet is 10.42.4.0/24): Client IP: 10.42.4.6 Destination: 255.255.255.255:67 Client Username: (blank) Protocol: DHCP (request) Action: Denied Connection Rule: (blank) Source Network: VPN Clients Destination Network: Local Host Result Code: 0xc0040014 FWX_E_FWE_SPOOFING_PACKET_DROPPED Network Interface: 10.42.4.11 --------------------------------------------------------- Original Client IP: 10.42.4.6 Destination: 10.42.1.1 Client Username: (valid user) Protocol: PING Action: Initiated Connection Rule: Allow PING to ISA Source Network: VPN Clients Destination Network: Local Host Result Code: 0x0 ERROR_SUCCESS Network Interface: (blank) I wasn't sure what this 10.42.4.11 network interface was - it certainly wasn't something I had setup - untill I saw it in Routing and Remote Access under IP Routing General as an interface called "Internal" bound to the same IP address. I also noticed that since ISA takes blocks of 10 IP addresses from DHCP for VPN, it had reserved 10.42.4.2-11. I'm not sure if it means anything, though. Thanks for your help.

    Read the article

  • configure spam assassin to delete all spam above a score domain wide and override individual settin

    - by Marlon
    Okay, so this is my scenario and what I want to try and do. I maintain a Red Hat email server running qmail and spamassassin. I have a domain that has well over 100 email account each with individual settings for spam scores and, whether or not to delete email incoming mail deemed spam. What I want to accomplish is to change all those email email accounts to say a more stringent spam score value, AND to enable the deletion of email immediately as it flagged as such, for EACH AND EVERY email box. In short, I want to be able to override a user's individual settings spam settings, with my own. Short of tediously going into each and every email box one by one, is there an way to do this all in one fell swoop? Any advice would be greatly appreciated! :-)

    Read the article

  • 4.5.1 4.4.0 DNS Query Failed

    - by Justin
    We are running Exchange 2010 and lately I have noticed that some outgoing messages get stuck in the queue with the error "451 4.4.0 DNS Query Failed". On every domain that this happens on I have been able to use nslookup to find the MX record and open a connection to their server over SMTP so I am reasonably sure that this problem is on my end. My send connector isn't routing mail through a smart host nor is is set to use a different DNS server to do the lookup so I'm stumped as to why these messages aren't going out. Any ideas?

    Read the article

  • Sendmail background process sometimes processes queue, but sendmail -q always works

    - by markmcb
    I'm using sendmail version 8.14.4 on Fedora 15 to send email. My Rails app uses delayed_job to queue up emails. Messages will queue up in /var/spool/mqueue as expected, but don't always get processed. I can see the messages and sendmail is definitely running in the background. Restarting the process does nothing. However, when I issue the sendmail -q command, sendmail gets to work and starts sending. The really odd thing is that this behavior only occurs sometimes. Other times message queue up and are delivered as expected. I've tried tweaking various sendmail configs to reduce the time between queue processing (for example, adding define('confMIN_QUEUE_AGE', '0')dnl to /etc/mail/sendmail.mc), but nothing seems to do the trick. Any ideas what might be the root cause?

    Read the article

  • Determine which active directory object is referred to by GUID in a Directory Synchronization Error Report

    - by Michael Shimmins
    We have active directory syncronization setup between our on-premises AD server and Microsoft hosted Exchange (business productivity online services). I've started getting a daily error report, which details an error for a specific AD user, however it references it by GUID. I can't find any info on how to translate that object guid into something meaningful so I can find and fix the problem. The error is reported as: Error 005: Unable to set the alias for this object in Microsoft Online Services because either the primary SMTP address, the e-mail nickname, or the SAM account name in the local Active Directory contains an invalid character. in reference to the Object GUID: CN={8443cbb4-5199-49f0-9529-ce965430dca6} How can I translate that object guid into a friendly object name?

    Read the article

  • Apache2 Segfault - need help interpreting this coredump (suspect cause is memcache / php session related)

    - by WayneDV
    Three Apache2 web servers running a PHP 5.2.3 web site. We're using Memcache to cache rendered pages but also as the storage engine of the PHP Sessions. At peak traffic times we're getting Apache segmentation faults on all three web servers and all HTTPD child processes segfault. My gut tells me that the increased Memcache traffic is stopping PHP sessions from being created or cleaned up and thus the processes die. Is it possible for someone to confirm that from the following? : #0 _zend_mm_free_int (heap=0x7fb67a075820, p=0x7fb67a011538) at /usr/src/debug/php-5.3.3/Zend/zend_alloc.c:2018 #1 0x00007fb665d02e82 in mmc_buffer_free (request=0x7fb67a011548) at /usr/src/debug/php-pecl-memcache-3.0.4/memcache-3.0.4/memcache_pool.c:50 #2 mmc_request_free (request=0x7fb67a011548) at /usr/src/debug/php-pecl-memcache-3.0.4/memcache-3.0.4/memcache_pool.c:169 #3 0x00007fb665d031ea in mmc_pool_free (pool=0x7fb67a00e458) at /usr/src/debug/php-pecl-memcache-3.0.4/memcache-3.0.4/memcache_pool.c:917 #4 0x00007fb665d0a2f1 in ps_close_memcache (mod_data=0x7fb66d625440) at /usr/src/debug/php-pecl-memcache-3.0.4/memcache-3.0.4/memcache_session.c:185 #5 0x00007fb66d1b0935 in php_session_save_current_state () at /usr/src/debug/php-5.3.3/ext/session/session.c:625 #6 php_session_flush () at /usr/src/debug/php-5.3.3/ext/session/session.c:1517 #7 0x00007fb66d1b0c1b in zm_deactivate_session (type=<value optimized out>, module_number=<value optimized out>) at /usr/src/debug/php-5.3.3/ext/session/session.c:2171 #8 0x00007fb66d2a719c in module_registry_cleanup (module=<value optimized out>) at /usr/src/debug/php-5.3.3/Zend/zend_API.c:2150 #9 0x00007fb66d2b1994 in zend_hash_reverse_apply (ht=0x7fb66d629d60, apply_func=0x7fb66d2a7180 <module_registry_cleanup>) at /usr/src/debug/php-5.3.3/Zend/zend_hash.c:755 #10 0x00007fb66d2a5c0d in zend_deactivate_modules () at /usr/src/debug/php-5.3.3/Zend/zend.c:866 #11 0x00007fb66d2541b5 in php_request_shutdown (dummy=<value optimized out>) at /usr/src/debug/php-5.3.3/main/main.c:1607 #12 0x00007fb66d32e037 in php_apache_request_dtor (r=0x7fb67a229658) at /usr/src/debug/php-5.3.3/sapi/apache2handler/sapi_apache2.c:509 #13 php_handler (r=0x7fb67a229658) at /usr/src/debug/php-5.3.3/sapi/apache2handler/sapi_apache2.c:681 #14 0x00007fb6784166f0 in ap_run_handler (r=0x7fb67a229658) at /usr/src/debug/httpd-2.2.15/server/config.c:158 #15 0x00007fb678419f58 in ap_invoke_handler (r=0x7fb67a229658) at /usr/src/debug/httpd-2.2.15/server/config.c:372 #16 0x00007fb6784254f0 in ap_process_request (r=0x7fb67a229658) at /usr/src/debug/httpd-2.2.15/modules/http/http_request.c:282 #17 0x00007fb678422418 in ap_process_http_connection (c=0x7fb67a2193a8) at /usr/src/debug/httpd-2.2.15/modules/http/http_core.c:190 #18 0x00007fb67841e1b8 in ap_run_process_connection (c=0x7fb67a2193a8) at /usr/src/debug/httpd-2.2.15/server/connection.c:43 #19 0x00007fb678429f4b in child_main (child_num_arg=<value optimized out>) at /usr/src/debug/httpd-2.2.15/server/mpm/prefork/prefork.c:662 #20 0x00007fb67842a21a in make_child (s=0x7fb679cd7860, slot=153) at /usr/src/debug/httpd-2.2.15/server/mpm/prefork/prefork.c:758 #21 0x00007fb67842aea4 in perform_idle_server_maintenance (_pconf=<value optimized out>, plog=<value optimized out>, s=<value optimized out>) at /usr/src/debug/httpd-2.2.15/server/mpm/prefork/prefork.c:893 #22 ap_mpm_run (_pconf=<value optimized out>, plog=<value optimized out>, s=<value optimized out>) at /usr/src/debug/httpd-2.2.15/server/mpm/prefork/prefork.c:1097 #23 0x00007fb678402890 in main (argc=1, argv=0x7fff6fecacb8) at /usr/src/debug/httpd-2.2.15/server/main.c:740 PHP.INI Follows: [PHP] engine = On short_open_tag = On asp_tags = Off precision = 14 y2k_compliance = On output_buffering = 4096 zlib.output_compression = Off implicit_flush = Off unserialize_callback_func = serialize_precision = 100 allow_call_time_pass_reference = Off safe_mode = Off safe_mode_gid = Off safe_mode_include_dir = safe_mode_exec_dir = safe_mode_allowed_env_vars = PHP_ safe_mode_protected_env_vars = LD_LIBRARY_PATH disable_functions = disable_classes = expose_php = On max_execution_time = 30 max_input_time = 60 memory_limit = 128M error_reporting = E_ALL & ~E_DEPRECATED display_errors = Off display_startup_errors = Off log_errors = Off log_errors_max_len = 1024 ignore_repeated_errors = Off ignore_repeated_source = Off report_memleaks = On track_errors = Off html_errors = Off variables_order = "GPCS" request_order = "GP" register_globals = Off register_long_arrays = Off register_argc_argv = Off auto_globals_jit = On post_max_size = 8M magic_quotes_gpc = Off magic_quotes_runtime = Off magic_quotes_sybase = Off auto_prepend_file = auto_append_file = default_mimetype = "text/html" doc_root = user_dir = enable_dl = Off file_uploads = On upload_max_filesize = 2M allow_url_fopen = On allow_url_include = Off default_socket_timeout = 60 [Date] [filter] [iconv] [intl] [sqlite] [sqlite3] [Pcre] [Pdo] [Phar] [Syslog] define_syslog_variables = Off [mail function] SMTP = localhost smtp_port = 25 sendmail_path = /usr/sbin/sendmail -t -i mail.add_x_header = On [SQL] sql.safe_mode = Off [ODBC] odbc.allow_persistent = On odbc.check_persistent = On odbc.max_persistent = -1 odbc.max_links = -1 odbc.defaultlrl = 4096 odbc.defaultbinmode = 1 [MySQL] mysql.allow_persistent = On mysql.max_persistent = -1 mysql.max_links = -1 mysql.default_port = mysql.default_socket = mysql.default_host = mysql.default_user = mysql.default_password = mysql.connect_timeout = 60 mysql.trace_mode = Off [MySQLi] mysqli.max_links = -1 mysqli.default_port = 3306 mysqli.default_socket = mysqli.default_host = mysqli.default_user = mysqli.default_pw = mysqli.reconnect = Off [PostgresSQL] pgsql.allow_persistent = On pgsql.auto_reset_persistent = Off pgsql.max_persistent = -1 pgsql.max_links = -1 pgsql.ignore_notice = 0 pgsql.log_notice = 0 [Sybase-CT] sybct.allow_persistent = On sybct.max_persistent = -1 sybct.max_links = -1 sybct.min_server_severity = 10 sybct.min_client_severity = 10 [bcmath] bcmath.scale = 0 [browscap] [Session] session.save_handler = files session.save_path = "/var/lib/php/session" session.use_cookies = 1 session.use_only_cookies = 1 session.name = PHPSESSID session.auto_start = 1 session.cookie_lifetime = 0 session.cookie_path = / session.cookie_domain = session.cookie_httponly = session.serialize_handler = php session.gc_probability = 1 session.gc_divisor = 1000 session.gc_maxlifetime = 1440 session.bug_compat_42 = Off session.bug_compat_warn = Off session.referer_check = session.entropy_length = 0 session.entropy_file = session.cache_limiter = nocache session.cache_expire = 180 session.use_trans_sid = 0 session.hash_function = 0 session.hash_bits_per_character = 5 url_rewriter.tags = "a=href,area=href,frame=src,input=src,form=fakeentry" [MSSQL] mssql.allow_persistent = On mssql.max_persistent = -1 mssql.max_links = -1 mssql.min_error_severity = 10 mssql.min_message_severity = 10 mssql.compatability_mode = Off mssql.secure_connection = Off [Assertion] [COM] [mbstring] [gd] [exif] [Tidy] tidy.clean_output = Off [soap] soap.wsdl_cache_enabled=1 soap.wsdl_cache_dir="/tmp" soap.wsdl_cache_ttl=86400 /etc/php.d/memcached.ini : session.save_path="tcp://memcache1:11211?persistent=1&weight=1&timeout=3&retry_interval=15"

    Read the article

  • Exchange 2007 ignoring Send Connectors (again)

    - by gravyface
    Wow, I'm at a loss here -- I posted this exact same question a while back and it's doing the exact same thing: my Send Connector I've created for "Microsoft Domains" (hotmail.com cost 1) is being ignored again and routed through the "Default" Send Connector (* cost 10). Last time, I had the same cost for both Send Connectors, but I've tried setting the Default connector to 5, 10, 100, etc. and regardless, all mail gets routed through that connector (which smarthosts through Postini). Besides calling an air strike on Redmond, what else can I do? MS is blocking Postini again, need to get this working permanently.

    Read the article

  • OpenSSH SFTP server with chroot() + user with chroot exception

    - by HannesFostie
    I am currently setting up an SFTP server but there is one detail I can't seem to figure out. When I add a user, I would like him to connect using his client and be able to write in his "root dir" right away. My Match case for the SFTP-users group currently has ChrootDirectory set as "/home/%u", and inside that directory I have to have a subdirectory owned by the user, while /home/%u itself is owned by root. Next to that, the "root dir" also has a couple files, .bashrc to name one. Is it possible to put these files somewhere else, remove them, or at least make them invisible to the user? Thanks EDIT: One more little thing I'd like to implement is for one account to have read (or rw, not sure yet) access to all other users' home directories. What is the easiest way to implement this? EDIT 2: Basically, having one user be an exception to the chroot rule would get me started.

    Read the article

  • I want to hide my email address when I send an email from a Lotus Notes Group Email [closed]

    - by Shaun Casey
    Possible Duplicate: How do I change the Respond To for Group Email adresses in Notes 6.5 When I send an email from a group mail box the email shows my email address as the sender. I would like to hide my email and only show my name. I am using Notes 6.5. Could you please advise if there is a way to set up my client to do this. I want this so the receiver responds to the group email not my personal email as it may be that I am not the one to do the fillow up to the response. There are 10 people in the group email.

    Read the article

  • Configure mod_wsgi WSGIScriptAlias with mod_rewrite

    - by Lazik
    I want to redirect ex.com to www.ex.com but I still want www.ex.com/ to point to my app.wsgi without it showing up in the url. When I use the conf below and I go to ex.com, I get a 404 error saying can't find www.ex.com/app.wsgi/ If I change the WSGIScriptAlias / /var/www/vhosts/ex/app.wsgi to WSGIScriptAlias /app.wsgi /var/www/vhosts/ex/app.wsgi Then all my url look like www.ex.com/app.wsgi/blabla/... Is it possible to use some kind of rule to redirect ex.com to www.ex.com and still keeping / as the app.wsgi root? my conf file <VirtualHost *:80> ServerName www.ex.com ServerAlias ex.com *.ex.com RewriteEngine On RewriteCond %{HTTP_HOST} !^www\. RewriteRule ^(.*)$ http://www.%{HTTP_HOST}/$1 [R=301,L] WSGIDaemonProcess ex user=www-data group=www-data processes=1 threads=5 WSGIScriptAlias / /var/www/vhosts/ex/app.wsgi <Directory /var/www/vhosts/ex> WSGIProcessGroup ex WSGIApplicationGroup %{GLOBAL} Order deny,allow Allow from all </Directory> </VirtualHost>

    Read the article

  • AutoComplete not working in Outlook 2007

    - by studiohack23
    When I go to create a new message in Outlook 2007, and I start typing the first few characters of a contact's name, no suggestions appear. I've just added all my contacts from a .csv file that was exported from Yahoo! Mail. If I type the name out, then click 'send', then it will ask me which of the contact's emails to send it to if the contact has multiple addresses. I've looked in the advanced options to make sure AutoComplete is on, which it its. What is going on? Thanks!

    Read the article

  • SBS2003 OWA not displaying images on external side

    - by JasonC
    I've got an SBS 2003 server with companyweb/remote owa site. After authenticating remotely to the https:/servername/remote site, and then clicking on Use Outlook Web Access, the mail/owa site displays only limited amounts of data with Loading... displayed (see first image). This is different when viewing the site on the server itself (see second image). Different browsers will display different types of data (last screenshot is Chrome - first two are IE). I feel IIS permissions on the virtual directories is the cause, but not certain. Forms-based authentication etc is working ok etc. Any suggestions? Authentication and getting email via ActiveSync is not a problem. I don't want to break anything, and it's not a major problem because the users only get their email via outlook and iphones anyway without problems. I'm more interested in finding out for my own info so please give me some suggestions to try. Thanks for looking!

    Read the article

  • proxy pass for activeMQ

    - by user1172482
    I have a apache server that I'm trying to use for proxy access my activeMQ admin page. I am able to load the inital landing page properly, but I can't seem to load any of the sub-pages (Queues, Connections, etc.). My proxypass rules on the apache server are the following: ProxyPass /foo http://10.5.124.108:8161/admin ProxyPassReverse /foo http://10.5.124.108:8161/admin The activeMQ installation included a activemq-httpd.conf file in /etc/httpd/conf.d/. Proxy connections there are enabled: ProxyRequests On ProxyVia On <Proxy *> Allow from all Order allow,deny </Proxy> ProxyPass /admin http://localhost:8161/admin ProxyPassReverse /admin http://localhost:8161/admin ProxyPass /message http://localhost:8161/admin/send ProxyPassReverse /message http://localhost:8161/admin/send From what I've read the proxypass rules should be recursive (the rule for /foo should also work for /foo/bar). Is there something else that I'm missing here that's preventing me from accessing pages beyond the initial admin landing page?

    Read the article

  • Wyse Z Class Thin Client (WES7) Image Deployment

    - by nsr81
    We are currently working on deploying a few Wyse WES7 thin clients (Z Class, exact model escapes me at the moment). We have WDM setup, and are able to see new clients show up, interact with them, pull/push images. Our current workflow is something like this: Unpack & boot up the device Disable Windows Firewall, reboot Device shows up in WDM Publish our custom image to the new device. My question is whether or not there is a way I can bypass step 2, and put my image on the client right out of the box. Either using PXE or USB boot disk, such that I can boot into some sort of menu and tell the client to pull a particular image from the WDM server. With HP thin clients, we have a rule setup which detects new clients on the network and pushes our custom image to them first time they show up. I haven't been able to figure it out with Wyse.

    Read the article

  • Using Google Talk with a non-apps, non-gmail Google account

    - by rymo
    I created a Google account with an existing e-mail address from a domain that is NOT hosted by Google. This address is not on an Apps domain and has no gmail service of any kind. Still I am able to add it as a Google account on an Android device with no problem. If the device is running Jelly Bean (where the Google Talk app allows switching between accounts) I can sign in and chat works fine. I can also sign into Talk with this account via the iGoogle home page. Now how can I use this account with a standalone chat client like iChat, Pidgin, or Empathy? It doesn't seem to work with login ID [email protected] using SSL to connect to server talk.google.com (tried ports 5222 and 5223). Are iGoogle and Android doing something magical that no other Jabber client is allowed, or am I just missing a step?

    Read the article

  • Recommended SpamAssassin update channels?

    - by Timo Geusch
    I'm currently using SpamAssassin on a couple of mail servers that I look after. SpamAssassin runs in the context of amavisd-new on those servers and with the usual bunch of plugins (FuzzyOCR, DCC, pyzor, razor). Currently the servers are getting their rule updates from the default SpamAssassin update channel (updates.spamassassin.org). Overall the setup seems to be reasonably effective but some types of spam seem to wander right through it even though I've made repeated attempts at training spamassassin. My guesstimate is that about 85%-90% of the spam that gets through policyd-weight makes it through the filters and it's been getting a lot worse recently as spammers are getting better at working their way through filters. Can someone recommend additional sources of filters to make SpamAssassin more effective? So far I've found OpenProtect's update channel but are there others worth looking at?

    Read the article

  • How do I use an include statement in a TXT record?

    - by Aglystas
    We have a client that is using an email service that requires a TXT domain key reocrd that is over 127 characters long. I'm pretty sure BIND allows this, however we run djbdns with tinydns and it looks as though it only supports txt records up to 127 characters. And the rest is being truncated. I was thinking I can do an include combining them, but I'm not really sure how. I was thinking of setting the value to somthing like... v=DKIM1; k=rsa; p=MIGfMA0GCSqGSIb3DQEBAQUAA4GNADCBiQKBgQC2GWCNaDTuC3include:bdk2._domainkey.mail.cutlerymania.com My thought is, will this grab the actual value located at that domain which only has one record which is a TXT record and simply append that information so the entire key record gets sent correctly?

    Read the article

  • what is acceptable datastore latency on VMware ESXi host?

    - by BeowulfNode42
    Looking at our performance figures on our existing VMware ESXi 4.1 host at the Datastore/Real-time performance data Write Latency Avg 14 ms Max 41 ms Read Latency Avg 4.5 ms Max 12 ms People don't seem to be complaining too much about it being slow with those numbers. But how much higher could they get before people found it to be a problem? We are reviewing our head office systems due to running low on storage space, and are tossing up between buying a 2nd VM host with DAS or buying some sort of NAS for SMB file shares in the near term and maybe running VMs from it in the longer term. Currently we have just under 40 staff at head office with 9 smaller branches spread across the country. Head office is runnning in an MS RDS session based environment with linux ERP and mail systems. In total 22 VMs on a single host with DAS made from a RAID 10 made of 6x 15k SAS disks.

    Read the article

  • SMTP Relay through exchange

    - by John
    Hi guys, We have a bit of a problem in that we want our printers to email our contractor whenever they develop a fault. The problem is on our corporate network we have no access through the firewall to the internet preventing us to use the external SMTP server. So i suppose the question is can we use our exchange server to do this? IE could I run an SMTP service that would forward to the exchange server which would then send the mail to the contractor? Any ideas welcome! Thanks John

    Read the article

  • Zantaz's EAS exchange archive product doesn't integrate with Outlook in Windows 7

    - by Chris Farmer
    I work at a place that uses Exchange with Outlook for mail, and they also use a product from Zantaz called "EAS" which does server-side archiving of old messages. One of the artifacts of this archival is that email attachments are missing from the archived messages when viewed in Outlook. EAS has a client tool that plugs into Outlook that enables easy retrieval of those archived messages and their attachments, but it doesn't seem to work when installed on Windows 7. I have no direct evidence of this, other than that it simply doesn't work on my Windows 7 machine, and some of our network support staff seem to corroborate this. The symptom is that Outlook seems to know nothing of the existence of this EAS app. The EAS app also has a system tray icon which is there and offers some minimal functionality, but the real goodness is the Outlook integration, which I sorely miss. So, my question is this: does anyone here know whether it's possible to coerce this EAS product into working correctly in Windows 7?

    Read the article

  • DKIM passes everywhere apart from Yahoo!

    - by Ian
    Hi, I'm using dkim-milter, Postfix on Ubuntu (I think I used these instructions for setting up). Anyway, using the reflectors such as Port25, BlackOps and Altn.com I get passes for DKIM: X-DKIM: OpenDKIM Filter v2.0.1 medusa.blackops.org o2SGTMSg005616 Authentication-Results: medusa.blackops.org; dkim=pass (1024-bit key) [email protected]; dkim-adsp=pass dkim=pass header.d=example.com (b=miSIxi7TMX; 1:0:good); Authentication-Results: verifier.port25.com header.d=example.com; dkim=pass (matches From: [email protected]); Yahoo gives this: Authentication-Results: mta1031.mail.ukl.yahoo.com from=; domainkeys=neutral (no sig); from=example.com; dkim=permerror (key failed) Where, obviously, example.com is my site address. Is anyone aware of anything different with Yahoo! that would stop these from signing? TIA

    Read the article

  • Apache -> redirect requests to PhpMyAdmin?

    - by AXL
    I am seeing a lot of requests where users are trying to request PhPMyAdmin directory on my web-server and I would like to put an end to it. They try a few different directories like PhpMyAdmin-2.10 or just PhpMyAdmin or just PhpMyAdmin-2.09 Would Apache Re-write rule be the best thing to re0direct them to a blackhole that bans their IP from accessing the IP again? Or I could simply create these directories and put in a javascript redirect to black-hole them as well. Thoughts on a good solution are appreciated.

    Read the article

  • IMAP email migration from Apptix to Office 365

    - by npiani
    I am having issues setting up a migration from Apptix to Office 365 of 41 users in my company. I've found a couple guides on the Microsoft website about how to do it (Thank you Google) but I keep coming up with problems. I am trying to set up a mailbox migration through IMAP to get all of my users' emails over to Office 365 before we make the transition over from Apptix. One of the forums suggested using IMAP, since a CSV file can be uploaded to Office 365 and it will check for incoming mail for each user every 24 hours. My problem is that when I do this, I just get errors. The link I got was this: http://help.outlook.com/en-us/140/ms.exch.ecp.emailmigrationstatuslearnmore.aspx#imap I was wondering if anyone has successfully managed this transition. I'm using imap.apptixemail.net as the IMAP server (FQDN) Thank you for the help in advance. Any help or push in the right direction would be amazing

    Read the article

  • Remove Downed Exchange Server from First Administrative Group

    - by Campo
    I had a server die. It is gone forever. It is still listed in the servers folder of the first administrative group in the Exchange System Manager. When I click "all tasks Remove Server" I get the following error: The Server "SERVERNAME" cannot be removed because: -One or more users currently use a mailbox on this server. These users must be moved to a mailbox store on a different server or be mail disabled before uninstalling this server. Facility: Exchange System Manager ID no: c103f492 Exchange System Manager Any help would be MUCH appreciated. I cannot access the mailbox stores anymore and I do not care about the lost mailboxes. We deleted the inactive and old users as well. So I am stumped on this one. I just need to remove the old machine. THANKS!

    Read the article

  • Cannot change port 25 to port 587

    - by Steve
    I am using outlook 2003. My email provider is Cox. Trying to change my out going port to 587 so I send mail while traveling. Others I know on Cox have done this with succes, but they are using newer version of outlook. When I go to change my existing email accounts, outlook will not allow me to change the settings. I can delete 25, but it will not allow me to type in 587. What am I doing wrong?

    Read the article

< Previous Page | 233 234 235 236 237 238 239 240 241 242 243 244  | Next Page >