Search Results

Search found 19992 results on 800 pages for 'font size'.

Page 241/800 | < Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >

• Atheros Wireless card shows up as two different models?

  - by geermc4

  Hi I've been fighting these wireless drivers for a few days and just recently i noticed that the model the Wireless controller appears in lspci is different sometimes. This is the data i have after installing Ubuntu Server 64 bit ~# lspci -k .... 04:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: AzureWave Device 1d89 Kernel driver in use: ath9k Kernel modules: ath9k ran some updates, restarted, all was good, all though it did say that linux-headers-server linux-image-server linux-server where beeing kept back. After that i installed ubuntu-desktop (aptitude install ubuntu-desktop --without-recommends) restarted and not only is the wireless not working anymore, but the hardware is listed as a different card ~# lspci -k .... 04:00.0 Ethernet controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) has no available drivers for it, still i tried to modprobe ath9k, they show up in lsmod as loaded, but still iw list shows nothing. this is what it looked like before the ubuntu-desktop instalation Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (14.0 dBm) * 2417 MHz [2] (15.0 dBm) * 2422 MHz [3] (15.0 dBm) * 2427 MHz [4] (15.0 dBm) * 2432 MHz [5] (15.0 dBm) * 2437 MHz [6] (15.0 dBm) * 2442 MHz [7] (15.0 dBm) * 2447 MHz [8] (15.0 dBm) * 2452 MHz [9] (15.0 dBm) * 2457 MHz [10] (15.0 dBm) * 2462 MHz [11] (15.0 dBm) * 2467 MHz [12] (15.0 dBm) (passive scanning) * 2472 MHz [13] (14.0 dBm) (passive scanning) * 2484 MHz [14] (17.0 dBm) (passive scanning) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor interface combinations are not supported Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS. What's with the hardware change? If it has 2, how can i make the AR9285 always load and disable AR5008, or, is it the same and it's just showing it different? :| Oh and I've tried this on Ubuntu 10.04 server, xubuntu 12.04, ubuntu 12.04 desktop and server. Thanks in advanced. -- Here's some more info, i have it setup in 2 hard drives, 1 works and the other one i'm using to figure it out The one that works... # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.147 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 74:2f:68:4a:26:73 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-18-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:fea00000-fea0ffff Here's where it doesn't # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.160 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network UNCLAIMED description: Ethernet controller product: AR5008 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:fea00000-fea0ffff Update I've noticed that if i blacklist the ath9k and ath9k_common modules lspci gives me the AR9285, but then I need to modprobe ath9k for it to work, does this make any sense? If so, why?

  Read the article

• Intel Centrino Wireless N 1000 doesn't work on a Lenovo Z560

  - by Timetraveler

  I upgraded my Ubuntu 11.04 to 11.10 and my Wifi has stopped working. I have a Lenovo Z560 that has Intel centrino wireless-N 1000. I have searched various threads having similar problems for a solution and have no success. The wlan0 is not even showing up in rfkill. Please help me find a solution. I am giving below the output of various debug commands. Thanks in advance. DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" ----##uname -a Linux gurucharapathy-laptop 3.0.0-17-generic-pae #30-Ubuntu SMP Thu Mar 8 17:53:35 UTC 2012 i686 i686 i386 GNU/Linux ----##lspci -nnk | grep -iA2 net 05:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1000 [8086:0084] Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN [8086:1315] Kernel modules: iwlagn 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) Subsystem: Lenovo Device [17aa:392e] Kernel driver in use: r8169 ----##iwconfig lo no wireless extensions. eth0 no wireless extensions. ----##iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. ----##rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no ----##lsmod Module Size Used by rfcomm 38408 8 bnep 17923 2 parport_pc 32114 0 ppdev 12849 0 binfmt_misc 17292 1 snd_hda_codec_hdmi 31426 1 snd_hda_codec_conexant 52460 1 uvcvideo 67271 0 videodev 85626 1 uvcvideo snd_hda_intel 28358 2 snd_hda_codec 91859 3 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec joydev 17393 0 snd_pcm 80435 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 i915 509554 9 drm_kms_helper 32889 1 i915 snd_rawmidi 25241 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28932 2 snd_pcm,snd_seq drm 196290 5 i915,drm_kms_helper snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq mei 36466 0 mac80211 393421 0 snd 55902 14 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 13575 0 intel_ips 17753 0 btusb 18160 2 i2c_algo_bit 13199 1 i915 soundcore 12600 1 snd bluetooth 148839 23 rfcomm,bnep,btusb cfg80211 172427 1 mac80211 psmouse 63474 0 serio_raw 12990 0 snd_page_alloc 14108 2 snd_hda_intel,snd_pcm sparse_keymap 13658 1 ideapad_laptop wmi 18744 0 video 18908 1 i915 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp ahci 21634 2 libahci 25761 1 ahci r8169 47200 0 ----##nm-tool NetworkManager Tool State: asleep Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: r8169 State: unmanaged Default: no HW Address: 88:AE:1D:DE:5F:9C Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on ----##lshw -C network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d6400000-d6401fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 02 serial: 88:ae:1d:de:5f:9c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=192.168.0.100 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d2410000-d2410fff memory:d2400000-d240ffff memory:d2420000-d243ffff

  Read the article

• Desktop Fun: Heroes of DC Comics Wallpaper Collection

  - by Asian Angel

  DC Comics has a great line-up of super hero characters and we have gathered together some of DC’s finest for you in today’s collection. Give your desktop super powers with our Heroes of DC Comics Wallpaper collection. Note: Click on the picture to see the full-size image—these wallpapers vary in size so you may need to crop, stretch, or place them on a colored background in order to best match them to your screen’s resolution. How to Make and Install an Electric Outlet in a Cabinet or DeskHow To Recover After Your Email Password Is CompromisedHow to Clean Your Filthy Keyboard in the Dishwasher (Without Ruining it)

  Read the article

• Large resolution differences

  - by Robin Betka

  I want to develop a game on multiple devices such as PC, Android or IOS. Want it to be in 1080p, but that means a massive scale down for the smartphones. I know how to do that, just render everything on a 1080p rendertarget and then render it on the screen smaller. But what should I do so that the scalling down doesn't look bad and blury? I can't do it vector based or anything because the sprites simply need a specific size. Should I make the sprites power of two size to get some nice mipmapping? And which other settings can I do? Or should I rather go with a lower resolution but then having a little bit worse look PC version? The performance seems not to be a problem for me, so would be sad not using 1080p because of other problems.

  Read the article

• Gauging Maturity of your BPM Strategy - part 1 / 2

  - by Sanjeev Sharma

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";} In this post I will discuss the essence of maturity assessment and the business imperative for doing the same in the context of BPM. Social psychology purports that an individual progresses from being a beginner to an expert in a given activity or task along four stages of self-awareness: Unconscious Incompetence where the individual does not understand or know how to do something and does not necessarily recognize the deficit and may even deny the usefulness of the skill. Conscious Incompetence where the individual recognizes the deficit, as well as the value of a new skill in addressing the deficit. Conscious Competence where the individual understands or knows how to do something but demonstrating the skill requires explicit concentration. Unconscious Competence where the individual has had so much practice with a skill that it has become "second nature" and serves as a basis of developing other complementary skills. We can extend the above thinking to an organization as a whole by measuring an organization’s level of competence in a specific area or capability, as an aggregate of the competence levels of individuals it is comprised of. After all organizations too like individuals, evolve through experience, develop “memory” and capabilities that are shaped through a constant cycle of learning, un-learning and re-learning. Hence the key to organizational success lies in developing these capabilities to enable execution of its strategy in-line with the external environment i.e. demand, competition, economy etc. However developing a capability merits establishing a base line in order to Assess the magnitude of improvement from past investments Identify gaps and short-comings Prioritize future investments in the right areas A maturity assessment is essentially an organizational self-awareness check that is aimed at depicting the “as-is” snapshot of an existing capability in-order to guide future investments to develop that capability in-line with business goals. This effectively is the essence of a maturity Organizational capabilities stem through its architecture, routines, culture and intellectual resources that are implicitly and explicitly embedded in its business processes. Given that business processes underpin realization of organizational capabilities, is what has prompted business transformation and process management efforts. Thus, the BPM capability of an organization needs to be measured on an on-going basis to ensure delivery of its planned benefits. In my next post I will describe Oracle’s BPM Maturity assessment methodology.

  Read the article

• Error when trying to get movies off my Camera

  - by matt wilkie

  How do I retrieve movies and audio files from my Canon PowerShot S5 IS camera? Shotwell only sees the pictures. Mounting the camera via "Places Canon Digital Camera" and then clicking twice on the resulting desktop icon yields this error: could not display "gphoto2://[usb:001,002]/" There is nothing in /media. update: output of sudo fdisk -l Disk /dev/sda: 40.0 GB, 40007761920 bytes 255 heads, 63 sectors/track, 4864 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x3ee33ee2 Device Boot Start End Blocks Id System /dev/sda1 2364 2612 1999872 82 Linux swap / Solaris /dev/sda2 * 1 2364 18979840 83 Linux /dev/sda3 2613 4864 18089159+ f W95 Ext'd (LBA) /dev/sda5 2613 4864 18089158+ b W95 FAT32 Partition table entries are not in disk order Solution: install gphotofs, then Nautilus shows camera contents similar to a standard usb storage device (though note that gphotofs does not yet support adding to or deleting contents).

  Read the article

• How can I find files quicker than find or locate?

  - by Chaitanya

  I have been using find command to find files on my 1 tb hard disk. it takes very long. then I used locate which proved to be faster with regular update using updatedb. But the limitation of locate is that I cannot find files with certain size or modified/created time. can you suggest me any ideas on how to find files at more speed or in that case how to pipe output of locate command in a way that all other information like size, time, etc. can be displayed or redirected to a file.

  Read the article

• Curiosity on any Smartphones that Run on Android 2.3.3 with Different Screen Reoslution

  - by David Dimalanta

  I have a question regarding about any smartphones that run only in Android 2.3.3. Is the size of screen or the screen resolution is always HVGA or does it have capable of running this OS (Android 2.3.3) on big screen size (4" to 5") at about 720x1280? I'm thinking of the game's compatibility depending on the version of the Android OS and the screen resolution, which affects the change of coordinates especially for assigning touch buttons and drag-n-drop at exact location, before I'm gonna decide to make one. My program works on the Android 4 ICS and Jellybean, however, will that work on Android 2.3.3 in spite of precise touch coordinate or just dependent on the screen resolution (regardless how large it is) as the X and Y coordinate? And take note, I'm using Eclipse IDE for Java developers.

  Read the article

• Live Virtual Class for Partners: Application Management

  - by Patrick Rood

  v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} November 11-12th Manageability Partner Community Application Management Suite Live Virtual Training This training will be offered to Oracle Partners over a live webcast during business hours. Each day will consist of approximately 2-3 hours of lecture/demos. It will be recorded and available for playback. Purpose: This virtual course is a comprehensive program of training sessions, prepared and presented by Product Managers. This ensures you have all the information you need to position and sell Oracle Application Management Suites. The sessions will be lecture based with demonstrations to complement. These sessions are interactive and everyone will be required to participate. Customer case studies will be used as appropriate and there will be plenty of opportunity for in-depth discussion. Please bring to the training an understanding of what Enterprise Manager 12c does for our customers, along with your own experiences to date. Logistics: Topic: Oracle Application Management Suite Training (2 Days - approx 2-3 Hour per Day) WebEx session details to be provided upon registration. Monday 11th November | 14:00PM GMT | 18:00PM Gulf (GMT+4) Tuesday 12th November | 14:00PM GMT | 18:00PM Gulf (GMT+4) (Back to the top) Copyright © 2012, Oracle. All rights reserved. Contact Us | Legal Notices and Terms of Use | Privacy Statement Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";}

  Read the article

• How to resize a /home partition in Kubuntu?

  - by Devon

  I was distro hopping for awhile in the past few months, so in order to keep all of my files secure, I made a partition of around 50 GB named Files to store all of my files in, and still have them for quick and easy access. However, now that I've found a distribution I'm comfortable with (Kubuntu 11.10), I would like to remove this partition, and have all of my files in my /home folder, in order to more easily deal with these files. I've moved all of my files in the partition to my /home folder (and still have plenty of room to spare), and now I'm trying to delete the partition and use the space for my /home folder. I can delete the partition just fine, however, I can't extend the /home folder into the unallocated space. Here's a screenshot of what I'm talking about. In order to change the size of the /home partition, I need to unmount it. But, I am unable to unmount it! How do I best extend the size of the partition?

  Read the article

• How to access photos from my Genius G-Shot P7545 camera?

  - by Florin

  I have a Genius G-Shot P7545 camera. In Windows I had just to plug in the camera to the usb and acces it like a usb stick. I tried to do that in Ubuntu 10.10 with no result. How can I acces the photots? With these comands I get: lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 015: ID 0784:1692 Vivitar, Inc. Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xcf5acf5a Device Boot Start End Blocks Id System /dev/sda1 * 1 2550 20478976 83 Linux /dev/sda3 2550 19458 135810048 f W95 Ext'd (LBA) /dev/sda5 2550 19458 135809024 83 Linux Unable to read /dev/sdb

  Read the article

• Detect duplicate in a subset from a set of elements

  - by Abhinav Shrivastava

  I have a set of numbers say : 1 1 2 8 5 6 6 7 8 8 4 2... I want to detect the duplicate element in subsets(of given size say k) of the above numbers... For example : Consider the increasing subsets(for example consider k=3) Subset 1 :{1,1,2} Subset 2 :{1,2,8} Subset 3 :{2,8,5} Subset 4 :{8,5,6} Subset 5 :{5,6,6} Subset 6 :{6,6,7} .... .... So my algorithm should detect that subset 1,5,6 contains duplicates.. My approach : 1)Copy the 1st k elements to a temporary array(vector) 2) using #include file in C++ STL...using unique() I would determine if there's any change in size of vector.. Any other clue how to approach this problem..

  Read the article

• Can't see my partitions after grub recovery

  - by dimbo

  I stupidly inserted the windows CD into my dual boot Ubuntu 11.10 / windows xp system. I just wanted to see if I could install windows on my external usb HD, but didn't actually go ahead with the install. It seems like the windows CD messed up my MBR and I had to use boot-repair and the ubuntu 11.10 live CD to gain access to ubuntu again. It seems to boot up a little differently (slower) but works. However, I now cant see any of my partitions in nautilus (there are 3). When I open gparted, it just shows my whole hard drive as unallocated (I know it has a windows partition that works and my ubuntu partition that I am using now). If I insert a usb pen, it is also not visible in nautilus but in gparted shows up as a FAT32 partition (which is correct although I cannot access it). sudo fdisk -l gives the following : demian@dimbo-TP:~$ sudo fdisk -l [sudo] password for demian: omitting empty partition (5) Disk /dev/sda: 320.1 GB, 320072933376 bytes 240 heads, 63 sectors/track, 41345 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x877b877b Device Boot Start End Blocks Id System /dev/sda1 * 63 63842309 31921123+ 7 HPFS/NTFS/exFAT /dev/sda2 63844350 133484084 34819867+ 5 Extended /dev/sda3 127636488 133484084 2923798+ 82 Linux swap / Solaris /dev/sda4 133484085 625137344 245826630 83 Linux /dev/sda5 63844352 123445247 29800448 83 Linux /dev/sda6 123447296 127635455 2094080 82 Linux swap / Solaris Disk /dev/sdb: 8100 MB, 8100249600 bytes 12 heads, 40 sectors/track, 32960 cylinders, total 15820800 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdb1 * 5992 15820799 7907404 c W95 FAT32 (LBA) Here is my grub.conf file. Like I said before, I had to use the 'boot-repair' utility with the live cd to get grub working again. I think that this utility maybe created a new grub for me because the startup is definitely not the same. The screen goes blank for a while, and then the ubuntu loading dots come up for a brief moment (instead of during the whole startup process) before the dektop is displayed. Anyway : # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=10 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.0.0-12-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a linux /boot/vmlinuz-3.0.0-12-generic root=UUID=5349ff67-b7b7-489f-a881-ae49c1dcd84a ro quiet splash vt.handoff=7 initrd /boot/initrd.img-3.0.0-12-generic } menuentry 'Ubuntu, with Linux 3.0.0-12-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a echo 'Loading Linux 3.0.0-12-generic ...' linux /boot/vmlinuz-3.0.0-12-generic root=UUID=5349ff67-b7b7-489f-a881-ae49c1dcd84a ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.0.0-12-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos6)' search --no-floppy --fs-uuid --set=root 5349ff67-b7b7-489f-a881-ae49c1dcd84a linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Microsoft Windows XP Professional (on /dev/sda1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 72A89361A89322A1 drivemap -s (hd0) ${root} chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### How can I get things back to normal. Thanks, Demian.

  Read the article

• What is the simplest human readable configuration file format?

  - by Juha

  Current configuration file is as follows: mainwindow.title = 'test' mainwindow.position.x = 100 mainwindow.position.y = 200 mainwindow.button.label = 'apply' mainwindow.button.size.x = 100 mainwindow.button.size.y = 30 logger.datarate = 100 logger.enable = True logger.filename = './test.log' This is read with python to a nested dictionary: { 'mainwindow':{ 'button':{ 'label': {'value':'apply'}, ... }, 'logger':{ datarate: {'value': 100}, enable: {'value': True}, filename: {'value': './test.log'} }, ... } Is there a better way of doing this? The idea is to get XML type of behavior and avoid XML as long as possible. The end user is assumed almost totally computer illiterate and basically uses notepad and copy-paste. Thus the python standard "header + variables" type is considered too difficult. The dummy user edits the config file, able programmers handle the dictionaries. Nested dictionary is chosen for easy splitting (logger does not need or even cannot have/edit mainwindow parameters).

  Read the article

• Finding files at more speed

  - by Chaitanya

  I have been using find command to find files on my 1 tb hard disk. it takes very long. then I used locate which proved to be faster with regular update using updatedb. But the limitation of locate is that I cannot find files with certain size or modified/created time. can you suggest me any ideas on how to find files at more speed or in that case how to pipe output of locate command in a way that all other information like size, time, etc. can be displayed or redirected to a file.

  Read the article

• error trying to display semi transparent rectangle

  - by scott lafoy

  I am trying to draw a semi transparent rectangle and I keep getting an error when setting the textures data. The size of the data passed in is too large or too small for this resource. dummyRectangle = new Rectangle(0, 0, 8, 8); Byte transparency_amount = 100; //0 transparent; 255 opaque dummyTexture = new Texture2D(ScreenManager.GraphicsDevice, 8, 8); Color[] c = new Color[1]; c[0] = Color.FromNonPremultiplied(255, 255, 255, transparency_amount); dummyTexture.SetData<Color>(0, dummyRectangle, c, 0, 1); the error is on the SetData line: "The size of the data passed in is too large or too small for this resource." Any help would be appreciated. Thank you.

  Read the article

• Multiple Vertex Buffers per Mesh

  - by Daniel

  I've run into the situation where the size of my mesh with all its vertices and indices, is larger than the (optimal) vertex buffer object upper limit (~8MB). I was wondering if I can sub-divide the mesh across multiple vertex buffers, and somehow retain validity of the indices. Ie a triangle with a indice at the first vertex, and an indice at the last (ie in seperate VBOs). All the while maintaining this within Vertex Array Objects. My thoughts are, save myself the hassle, and for meshes (messes :P) such as this, just use the necessary size ( 8MB); which is what I do at the moment. But ideally my buffer manager (wip) at the moment is using optimal sizes; I may just have to make a special case then... Any ideas? If necessary, a simple C++ code example is appreciated. Note: I have also cross-posted this on stackoverflow, as I was not sure as to which it would be more suitable (its partly a design question).

  Read the article

• Why is my mdadm raid-1 recovery so slow?

  - by dimmer

  On a system I'm running Ubuntu 10.04. My raid-1 restore started out fast but quickly became ridiculously slow (at this rate the restore will take 150 days!): dimmer@paimon:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdc1[2] sdb1[1] 1953513408 blocks [2/1] [_U] [====>................] recovery = 24.4% (477497344/1953513408) finish=217368.0min speed=113K/sec unused devices: <none> Eventhough I have set the kernel variables to reasonably quick values: dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_min 1000000 dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_max 100000000 I am using 2 2.0TB Western Digital Hard Disks, WDC WD20EARS-00M and WDC WD20EARS-00J. I believe they have been partitioned such that their sectors are aligned. dimmer@paimon:/sys$ sudo parted /dev/sdb GNU Parted 2.2 Using /dev/sdb Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00M (scsi) Disk /dev/sdb: 2000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 (parted) unit s (parted) p Number Start End Size File system Name Flags 1 2048s 3907028991s 3907026944s ext4 (parted) q dimmer@paimon:/sys$ sudo parted /dev/sdc GNU Parted 2.2 Using /dev/sdc Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00J (scsi) Disk /dev/sdc: 2000GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 I am beginning to think that I have a hardware problem, otherwise I can't imagine why the mdadm restore should be so slow. I have done a benchmark on /dev/sdc using Ubuntu's disk utility GUI app, and the results looked normal so I know that sdc has the capability to write faster than this. I also had the same problem on a similar WD drive that I RMAd because of bad sectors. I suppose it's possible they sent me a replacement with bad sectors too, although there are no SMART values showing them yet. Any ideas? Thanks. As requested, output of top sorted by cpu usage (notice there is ~0 cpu usage). iowait is also zero which seems strange: top - 11:35:13 up 2 days, 9:40, 3 users, load average: 2.87, 2.58, 2.30 Tasks: 142 total, 1 running, 141 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.2%sy, 0.0%ni, 99.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3096304k total, 1482164k used, 1614140k free, 617672k buffers Swap: 1526132k total, 0k used, 1526132k free, 535416k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 45 root 20 0 0 0 0 S 0 0.0 2:17.02 scsi_eh_0 1 root 20 0 2808 1752 1204 S 0 0.1 0:00.46 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/0 4 root 20 0 0 0 0 S 0 0.0 0:00.17 ksoftirqd/0 5 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 6 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/1 ... dmesg errors, definitely looking like hardware: [202884.000157] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [202884.007015] ata5.00: failed command: FLUSH CACHE EXT [202884.013728] ata5.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [202884.013730] res 40/00:00:ff:59:2e/00:00:35:00:00/e0 Emask 0x4 (timeout) [202884.033667] ata5.00: status: { DRDY } [202884.040329] ata5: hard resetting link [202889.400050] ata5: link is slow to respond, please be patient (ready=0) [202894.048087] ata5: COMRESET failed (errno=-16) [202894.054663] ata5: hard resetting link [202899.412049] ata5: link is slow to respond, please be patient (ready=0) [202904.060107] ata5: COMRESET failed (errno=-16) [202904.066646] ata5: hard resetting link [202905.840056] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [202905.849178] ata5.00: configured for UDMA/133 [202905.849188] ata5: EH complete [203899.000292] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [203899.007096] ata5.00: failed command: IDENTIFY DEVICE [203899.013841] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [203899.013843] res 40/00:00:ff:f9:f6/00:00:38:00:00/e0 Emask 0x4 (timeout) [203899.041232] ata5.00: status: { DRDY } [203899.048133] ata5: hard resetting link [203899.816134] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [203899.826062] ata5.00: configured for UDMA/133 [203899.826079] ata5: EH complete [204375.000200] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204375.007421] ata5.00: failed command: IDENTIFY DEVICE [204375.014799] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204375.014800] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204375.044374] ata5.00: status: { DRDY } [204375.051842] ata5: hard resetting link [204380.408049] ata5: link is slow to respond, please be patient (ready=0) [204384.440076] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204384.449938] ata5.00: configured for UDMA/133 [204384.449955] ata5: EH complete [204395.988135] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204395.988140] ata5.00: failed command: IDENTIFY DEVICE [204395.988147] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204395.988149] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204395.988151] ata5.00: status: { DRDY } [204395.988156] ata5: hard resetting link [204399.320075] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204399.330487] ata5.00: configured for UDMA/133 [204399.330503] ata5: EH complete

  Read the article

• Exalogic 2.0.1 Tea Break Snippets - Modifying the Default Shipped Template

  - by The Old Toxophilist

  Having installed your Exalogic Virtual environment by default you have a single template which can be used to create your vServers. Although this template is suitable for creating simple test or development vServers it is recommended that you look at creating your own custom vServers that match the environment you wish to build and deploy. Therefore this Tea Time Snippet will take you through the simple process of modifying the standard template. Before You Start To edit the template you will need the Oracle ModifyJeos Utility which can be downloaded from the eDelivery Site. Once the ModifyJeos Utility has been downloaded we can install the rpms onto either an existing vServer or one of the Control vServers. rpm -ivh ovm-modify-jeos-1.0.1-10.el5.noarch.rpm rpm -ivh ovm-template-config-1.0.1-5.el5.noarch.rpm Alternatively you can install the modify jeos packages on a none Exalogic OEL installation or a VirtualBox image. If you are doing this, assuming OEL 5u8, you will need the following rpms. rpm -ivh ovm-modify-jeos-1.0.1-10.el5.noarch.rpm rpm -ivh ovm-el5u2-xvm-jeos-1.0.1-5.el5.i386.rpm rpm -ivh ovm-template-config-1.0.1-5.el5.noarch.rpm Base Template If you have installed the modify onto a vServer running on the Exalogic then simply mount the /export/common/images from the ZFS storage and you will be able to find the el_x2-2_base_linux_guest_vm_template_2.0.1.1.0_64.tgz (or similar depending which version you have) template file. Alternatively the latest can be downloaded from the eDelivery Site. Now we have the Template tgz we will need the extract it as follows: tar -zxvf  el_x2-2_base_linux_guest_vm_template_2.0.1.1.0_64.tgz This will create a directory called BASE which will contain the System.img (VServer image) and vm.cfg (VServer Config information). This directory should be renamed to something more meaning full that indicates what we have done to the template and then the Simple name / name in the vm.cfg editted for the same reason. Modifying the Template Resizing Root File System By default the shipped template has a root size of 4 GB which will leave a vServer created from it running at 90% full on the root disk. We can simply resize the template by executing the following: modifyjeos -f System.img -T <New Size MB>) For example to imcrease the default 4 GB to 40 GB we would execute: modifyjeos -f System.img -T 40960) Resizing Swap We can modify the size of the swap space within a template by executing the following: modifyjeos -f System.img -S <New Size MB>) For example to increase the swap from the default 512 MB to 4 GB we would execute: modifyjeos -f System.img -S 4096) Changing RPMs Adding RPMs To add RPMs using modifyjeos, complete the following steps: Add the names of the new RPMs in a list file, such as addrpms.lst. In this file, you should list each new RPM in a separate line. Ensure that all of the new RPMs are in a single directory, such as rpms. Run the following command to add the new RPMs: modifyjeos -f System.img -a <path_to_addrpms.lst> -m <path_to_rpms> -nogpg Where <path_to_addrpms.lst> is the path to the location of the addrpms.lst file, and <path_to_rpms> is the path to the directory that contains the RPMs. The -nogpg option eliminates signature check on the RPMs. Removing RPMs To remove RPM s using modifyjeos, complete the following steps: Add the names of the RPMs (the ones you want to remove) in a list file, such as removerpms.lst. In this file, you should list each RPM in a separate line. The Oracle Exalogic Elastic Cloud Administrator's Guide provides a list of all RPMs that must not be removed from the vServer. Run the following command to remove the RPMs: modifyjeos -f System.img -e <path_to_removerpms.lst> Where <path_to_removerpms.lst> is the path to the location of the removerpms.lst file. Mounting the System.img For all other modifications that are not supported by the modifyjeos command (adding you custom yum repositories, pre configuring NTP, modify default NFSv4 Nobody functionality, etc) we can mount the System.img and access it directly. To facititate quick and easy mounting/unmounting of the System.img I have put together the simple scripts below. MountSystemImg.sh #!/bin/sh # The script assumes it's being run from the directory containing the System.img # Export for later i.e. during unmount export LOOP=`losetup -f` export SYSTEMIMG=/mnt/elsystem # Make Temp Mount Directory mkdir -p $SYSTEMIMG # Create Loop for the System Image losetup $LOOP System.img kpartx -a $LOOP mount /dev/mapper/`basename $LOOP`p2 $SYSTEMIMG #Change Dir into mounted Image cd $SYSTEMIMG UnmountSystemImg.sh #!/bin/sh # The script assumes it's being run from the directory containing the System.img # Assume the $LOOP & $SYSTEMIMG exist from a previous run on the MountSystemImg.sh umount $SYSTEMIMG kpartx -d $LOOP losetup -d $LOOP Packaging the Template Once you have finished modifying the template it can be simply repackaged and then imported into EMOC as described in "Exalogic 2.0.1 Tea Break Snippets - Importing Public Server Template". To do this we will simply cd to the directory above that containing the modified files and execute the following: tar -zcvf <New Template Directory> <New Template Name>.tgz The resulting.tgz file can be copied to the images directory on the ZFS and uploadd using the IB network. This entry was originally posted on the The Old Toxophilist Site.

  Read the article

• Drawing of a huge model - How to regain performance?

  - by marc wellman

  I have a huge model I want to draw in my XNA application but because of its size I am experiencing a tremendous loss of performance. The model has about ~50 000 000 edges and has a size on disk of 205 MB in DirectX Format. Please don't ask whether this model has to be that big - yes it has! Is there a way to transfer the model directly to my GPU in order to let the GPU do the drawing like when transferring a VertexBuffer like this: graphicsDevice.Vertices[1].SetSource(_instanceBuffers[i], 0, _sizeofMatrix); because when I try to fill a vertexBuffer with all the vertices I am getting a OutOfMemoryException.

  Read the article

• Dual Boot Ubuntu and Windows 7: BOOTMGR is missing when I tried to boot in Windows

  - by Simon Polak

  So, I don't know what exactly how I managed to delete the MBR record on windows partition. But let me explain what I did next, I ran the ubuntu boot repair tool and now Windows is not even listed in my grub loader. So I went and booted with windows cd and choose repair. Then I ran ubuntu boot repair again via live cd. Here is the log http://paste.ubuntu.com/1426181/. Still no luck. Looks like osprobe can't detect windows on my /dev/sda2 partition. Any clues ? Here is how my partitions look like: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x525400d1 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 509620669 254706911 7 HPFS/NTFS/exFAT /dev/sda3 509622270 976773119 233575425 5 Extended /dev/sda5 509622272 957757439 224067584 83 Linux /dev/sda6 957759488 976773119 9506816 82 Linux swap / Solaris

  Read the article

• Unable to mount 1TB USB external HDD - Error

  - by superbDeveloper

  Hi, I'm getting an error when I plug in my 1TB USB external HDD, the wierd thing about this is that it was working fine before and I've been using it for about a couple of months now. yesterday I compressed one of the folders which had about 120GB of data but the compression failed after an hour and I decided to unmount the drive and shut everything down. Today when I tried to plug in the drive I got the following error: Error mounting: mount: wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so output of cat /proc/partitions below muzikayise@muzikayise-supercom:~$ sudo fdisk -l /dev/sdc Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x39dcba64 Device Boot Start End Blocks Id System please will someone kindly assist with this? thanks in advance,

  Read the article

• How can I assign id to subject input box in simple machines forum?

  - by Mahesh Bhat

  I have installed the simple machines forum. For my requirement I need to change the subject input box. Presently the subject input box has the following code <input type="text" class="input_text" maxlength="80" size="80" tabindex="1" name="subject"> I want this to be changed like <input type="text" id="subject" class="input_text" maxlength="80" size="80" tabindex="1" name="subject"> How can I do this? I browsed through many files in simple machines forum and couldn't find out. Anyone one simple machines forum please help me

  Read the article

• Marshalling C# Structs into DX11 cbuffers

  - by Craig

  I'm having some issues with the packing of my structure in C# and passing them through to cbuffers I have registered in HLSL. When I pack my struct in one manner the information seems to be able to pass to the shader: [StructLayout(LayoutKind.Explicit, Size = 16)] internal struct TestStruct { [FieldOffset(0)] public Vector3 mEyePosition; [FieldOffset(12)] public int type; } This works perfectly when used against this HLSL fragment: cbuffer PerFrame : register(b0) { Vector3 eyePos; int type; } float3 GetColour() { float3 returnColour = float(0.0f, 0.0f, 0.0f); switch(type) { case 0: returnColour = float3(1.0f, 0.0f, 0.0f); break; case 1: returnColour = float3(0.0f, 1.0f, 0.0f); break; case 2: returnColour = float3(0.0f, 0.0f, 1.0f); break; } return returnColour; } However, when I use the following structure definitions... // Note this is 16 because HLSL packs in 4 float 'chunks'. // It is also simplified, but still demonstrates the problem. [StructLayout(Layout.Explicit, Size = 16)] internal struct InternalTestStruct { [FieldOffset(0)] public int type; } [StructLayout(LayoutKind.Explicit, Size = 32)] internal struct TestStruct { [FieldOffset(0)] public Vector3 mEyePosition; //Missing 4 bytes here for correct packing. [FieldOffset(16)] public InternalTestStruct mInternal; } ... the following HLSL fragment no longer works. struct InternalType { int type; } cbuffer PerFrame : register(b0) { Vector3 eyePos; InternalType internalStruct; } float3 GetColour() { float3 returnColour = float(0.0f, 0.0f, 0.0f); switch(internaltype.type) { case 0: returnColour = float3(1.0f, 0.0f, 0.0f); break; case 1: returnColour = float3(0.0f, 1.0f, 0.0f); break; case 2: returnColour = float3(0.0f, 0.0f, 1.0f); break; } return returnColour; } Is there a problem with the way I am packing the struct, or is it another issue? To re-iterate: I can pass a struct in a cbuffer so long as it does not contain a nested struct.

  Read the article

• Fix Windows MBR using Ubuntu Live CD

  - by kova

  I'm trying to fix the MBR using Ubuntu live CD. I already have the ms-sys installed but from the threads that I saw, I'm not completely sure in which /dev I should execute the command: sudo ms-sys --mbr7 /dev/??? (is it mbr7 the correct option when using Windows 7?) ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1f205b1f Device Boot Start End Blocks Id System /dev/sda1 * 38 38 0 0 Empty /dev/sda2 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda3 206848 155854847 77824000 7 HPFS/NTFS/exFAT /dev/sda4 155854848 625137663 234641408 7 HPFS/NTFS/exFAT ubuntu@ubuntu:~$ Why is /dev/sda1 empty? I'm trying to fix the MBR because I'm getting a black screen when trying to load the operating system.

  Read the article

< Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >