Search Results

Search found 10536 results on 422 pages for 'cpu usage'.

Page 245/422 | < Previous Page | 241 242 243 244 245 246 247 248 249 250 251 252  | Next Page >

  • Linux QoS: bulk data transmission during idle times

    - by syneticon-dj
    How would I do a QoS setup where a certain low-priority data stream would get up to X Mbps of bandwidth, but only if the current total bandwidth (of all streams/classes) on this interface does not exceed X? At the same time, other data streams / classes must not be limited to X. The use case is an ISP billing the traffic by calculating the bandwidth average over 5 minute intervals and billing the maximum. I would like to keep the maximum usage to a minimum (i.e. quench the bulk transfer during interface busy times) but get the data through during idle/low traffic times. Looking at the frequently used classful schedulers CBQ, HTB and HSFC I cannot see a straightforward way to accomplish this.

    Read the article

  • Alternatives to amavis for RAM-bound server

    - by rsuarez
    I'm running a small VPS server that works as web and mail server. It has only 256MB of RAM, and it's sucking 100MB of swap constantly. I've found that one of the culprits is amavis, taking about 30MB of resident memory, and would like to ditch it and use some alternative. I don't have much mail daily, so it being a bit slower wouldn't be a problem. I'd like to avoid Spamassassin altogether, if possible, because it's quite big even if used in offline mode. I'm already using RBLs and a few small blacklists, and used greylisting for a while but abandoned it because it gave me a few problems (don't remember which; I think it was related to not configuring properly white lists for several big ISPs). So, is there some alternative to amavis that I could use without much RAM (and if possible, CPU) usage? Thanks in advance.

    Read the article

  • Is an eee-pc with an Atom N550 dual core OK for Rails 3 development?

    - by dan
    I'm buying an Asus eee-pc 1015PEM and hope to do test-driven Rails 3 development on it. Is the CPU fast enough or too painfully slow for this? I plan on installing Ubuntu. I currently develop on a 11 inch Macbook Air 2010 model. It works fine as a Rails development machine. But for some reason I'm drawn to developing on a cheap little netbook. I don't use any IDE's, and my development workflow is mostly switching between Vim, Gnu Screen, and bash.

    Read the article

  • seamless mode remote desktop connection from linux to windows

    - by mateusz.fiolka
    I am a programmer using Linux as my main OS, however sometimes I need to use windows (ie, office, ea). I'm running qemu with kvm to access the windows "machine". I would like to achieve something that is described here: https://help.ubuntu.com/community/SeamlessVirtualization (It means I would be able to run chosen applications on Windows and then display them locally on Linux as separate windows achieving good desktop integration). However seamless rdp is buggy and doesn't work on my machine (probably because I'm using a tiling window manager and a 64bit system). Are you aware of any other solution then rdp seamless mode? I would prefer to still use quemu because it uses cpu hardware virtualization, so different protocol/client combination would be preferable.

    Read the article

  • Why am I seeing excessive disk activity when installing applications?

    - by Kev
    I'm running Windows 7 Ultimate 64 bit on a Dell Vostro 1720 with 8GB of RAM, 7200RPM Disk, 2.53 GHz Core2Duo (Windows 7 64 bit is a supported option and the laptop came with the OS pre-installed). I'm noticing some fairly excessive disk activity when running installers. For example the Visual Studio 2010 RC installer constantly accessed the disk for ~10 minutes. It was so excessive that I was unable to use the machine until this ceased. Today I installed Trillian Astra 4.1 for Windows (latest build from the website). Again when I ran the installer I was pretty much locked out of the machine until the disk activity calmed down. In both cases when I eventually managed to launch task manager I could see that the CPU was sitting at around 5% to 7% utilisation whilst this was going on. All other disk related activity is fine, the machine is snappy and applications launch without delay. It's just when I run an installer I see this odd behaviour. Why would this be?

    Read the article

  • Internet Explorer background-color hover problem

    - by danilo
    I have a strange Problem with table formating using IE 7. My table looks like this: In IE, when using border-collapse, the borders don't get displayed correctly. That's why I used this fix: .table-vmlist td { border-top: 1px solid black; } td.col-vm-status, tr.row-details td { border-left: 1px solid black; } td.col-vm-rdp, tr.row-details td { border-right: 1px solid black; } .table-vmlist { border-bottom: 1px solid black;} When hovering over the row, it gets highlighted with CSS: .table-vmlist tr.row-vm { background-color: #A4C3EF; } .table-vmlist tr.row-vm:hover { background-color: #91BAEF; } Now, in IE 7, when moving the mouse from the top to the bottom of the list, every row gets highlighted correctly and no problems happen. But if I move my mouse pointer from the bottom of the list to the top, every second row seems to loose the border. Can someone explain what the problem is, and how to solve it? This is my markup: <tr class="row-vm"> <td class="col-vm-status status-1"><img title="Host Down" alt="Down" src="/Technik/vm-management/img/hoststatus_1.png"></td> <td class="col-vm-name">V1-VM-1</td> <td class="col-vm-stati"> <img title="Ping" alt="Ping status" src="/Technik/vm-management/img/servicestatus_3.png"> <img title="CPU" alt="CPU status" src="/Technik/vm-management/img/servicestatus_3.png"> <img title="RAM" alt="RAM status" src="/Technik/vm-management/img/servicestatus_3.png"> <img title="C:\ Diskspace" alt="Disk space status" src="/Technik/vm-management/img/servicestatus_3.png"> </td> <td class="col-vm-owner">kus</td> <td class="col-vm-purpose">Citrix Testserver</td> <td class="col-vm-ip">-</td> <td class="col-vm-uptime">-</td> <td class="col-vm-rdp">&nbsp;</td> </tr> And the CSS: /* VM-Tabelle formatieren */ .table-vmlist { border-collapse: collapse; } .table-vmlist tr { border: 1px solid black; } .table-vmlist tr.row-header { border: none; } .table-vmlist tr.row-vm { background-color: #A4C3EF; } .table-vmlist tr.row-vm:hover { background-color: #91BAEF; } .table-vmlist th { text-align: left; } .table-vmlist td { } .table-vmlist th, table td { padding: 2px 0px; } /* Spaltenbreite der VM-Tabelle festlegen */ .table-vmlist #col-status { width: 25px; } .table-vmlist #col-stati { width: 90px; } .table-vmlist #col-owner { width: 90px; } .table-vmlist #col-ip { width: 100px; } .table-vmlist #col-uptime { width: 70px; } .table-vmlist #col-rdp { width: 25px; } .table-vmlist tr.row-details td { padding: 0px 10px; } /* Kein Rahmen um verlinkte Bilder */ a img { border-width: 0px; } /* Für Einschaltknopf Hand-Cursor anstatt normalen Pfeil anzeigen */ td.status-1 img { cursor: pointer; } img.ajax-loader { margin-left: 2px; } IE fix: .table-vmlist td { border-top: 1px solid black; } td.col-vm-status, tr.row-details td { border-left: 1px solid black; } td.col-vm-rdp, tr.row-details td { border-right: 1px solid black; } .table-vmlist { border-bottom: 1px solid black;}

    Read the article

  • PC with 2 RAMs of different frequencies (1GB 533MHz + 2GB 667MHz) showing only 2GB RAM

    - by srinivas
    I have 6 years old PC with 1.25GB (1GB + 256MB) of DDR2 533MHz RAM. As computer has become very slow and memory usage reaching its limits most of the times, i decided to upgrade RAM. But unfortunately, im not finding retailers selling DDR2 533Mhz RAM near my area. Since I was not sure mixing up RAMs of different frequencies, i searched in web. Most results said they can be mixed but computer would run at lower frequency of the 2 RAMs. So I bought 2GB DDR2 667Mhz RAM expecting my pc to have 3GB RAM running at 533 MHz. But computer properties page shows only 2GB RAM. BIOS settings too show the slot with 2GB 667MHz as ACTIVE and other slot with 1GB 533MHz as "NOT INSTALLED". When I removed 2GB RAM, they computer shows only 1GB RAM. So for some reason, 1GB RAM is not getting detected/used. What is the problem here? thanks in advance.

    Read the article

  • Amazon EC2- micro-instance vs single small/medium instance

    - by shashankaholic
    I have a chat application using stack of Openfire, Tomcat6 and MySQL. Currently, i have installed all these servers on single Linux micro-instance(613 MB memory). Even in low user base 10-20 i am encountering CPU overload which is quite obvious here. As, i am new to Amazon EC2 can somebody suggest me how to scale up my architecture according to traffic use? should i use separate micro instances for every app server(openfire,mysql,tomcat6) should i use single small or medium instance for whole server stack. Some factors in context: high reliance on MYSQL high memory usage due to file transfer web-application interacting with other Amazon service like S3,SES

    Read the article

  • Do I need a license to create pdf files? [closed]

    - by Fire-Dragon-DoL
    I hope this is the correct place where I could ask this question. My mother is an accountant with a degree in economics. She works as a freelancer and she needs some licenses for her job. The biggest problem is adobe acrobat standard, which costs 400€, quite a lot. I want understand if she must buy it to create pdf files or she can use some free (even for commercial use) programs that she has because of her job (the chamber of commerce provide some advantages to accountants). She is actually using PDFCreator, which as I can read is free for business usage (open source also!!): http://sourceforge.net/projects/pdfcreator/ Thanks for any suggestion

    Read the article

  • VMware Fusion / New Machine / verify VMs?

    - by drewk
    I just got a 15" MacBook Pro with 8GB RAM, 2.66 i7 and 500GB SSD. Very sweet and fast! My old machine was 2.66 Core 2 Duo. I used Migration Assistant to migrate my old MBP to the new. When I started VMware to run Windows and Ubuntu I got the message first This VM has been moved or copied to a new machine. Did you move or copy it? I answered Copied. Then I got the message this CPU is a different configuration than the machine that created the VM. You may get unpredictable results. I answered Open Anyway. Windows XP, Windows 7, and Ubuntu all seem to work OK, but how can I verify? Is there some form of test harness for a VM? I have had a VM degrade and become unusable with very catastrophic data loss (on Parallels...), so I am a bit paranoid. Thanks,

    Read the article

  • Accessing WindowsXP shared printer from macbook?

    - by mobibob
    My new printer is setup on WindowsXP, it works and it is configured as a shared printer. I then setup a printer from Mac OSX 10.6.3 using the approved driver from the setup CD. I browsed for the printer via the network. When I send a test page, it queues, but never prints. Its as if the driver thinks the printer is local to the mac and just never finishes printing. THe configuration shows as: smb://dragoneye/CanonMP2 Where dragoneye is the name of the Windows XP server and the CanonMP2 is the little multi-purpose printer. My other Windows' CPU can setup and print. Is this a known problem or am I missing a setting??

    Read the article

  • Areca 1880ix RAID hangs

    - by Dave
    Areca RAID controller ARC-1880ix-12 (firmware 1.50) hangs when on high load. My setup is: Chenbro 3U chassis Intel S5500BC mainboard Xeon 5603 CPU 16GB of RAM 12 Seagate SAS drives ST32000645SS (2 of them as hot spare, 10 as RAID10) Mellanox Infiniband HBA card This server is working as external infiniband storage for Xen VMs. When load is quite big Areca's firmware hangs - it becomes unreachable even from Areca's ethernet adapter. After resetting the server power it returns to normal operation. While Areca is hanged I can confirm that it is powered (ethernet link is active) and Infiniband HBA works Ok. Thanks in advance for any idea or suggestion where the problem might be!

    Read the article

  • VMWare ESX installation on sata disk

    - by ilansch
    I have a PC with Gigabyte H77 motherboard with Intel I5-3550 CPU 8 GB RAM 1600MHz and a 500GB Harddisk (7200RPM) - WD Sata III disk I wish to install esx on it and run some virtual machines on it. not alot, something like 2-3 VMs. My hardisk is Sata, is it possible to install ESX Server on it ? I am not worried about loading issues. When i try loading the installation it writes it cannot detect my disk (since its not SCSI disk). How can i bypass this ? or find a solution. thanks

    Read the article

  • Understanding why a 450W power supply is destroying my ATX motherboards but not mATX

    - by T. Webster
    Maybe I'm missing something really obvious here, but after going through 3 new motherboards in trying to build my new machine, I'm finally certain that the 450W power supply I bought has been destroying them. It seems like it should be simple: just connect the connectors where they fit and switch the thing on. But today after hooking it to my ASUS Sabertooth 990FX TUF Series Motherboard and switching it on, I could see and smell the smoke coming out of the motherboard. What I don't get is why I can hook this same 450W power supply up to my mATX motherboard and not run into the same problem. What am I missing here? Where on the box or manual is this? (I have 8x2 GB RAM, AMD FX-4100 3.6GHz CPU, 1 512MB ATI graphics card, 1 WD 7200 RPM SATA hard drive. )

    Read the article

  • cygwin rsync over ssh very slow

    - by Waleed Hamra
    I have 2 machines running Windows Xp SP3. I have cygwin installed on both, version 1.7. I have rsync and ssh installed on both, and configured using default settings as per ssh-host-config and ssh-user-config programs provided. I moved the public keys into their respective locations, and basically ssh is working fine. i began an rsync operation, using: rsync -av --delete --hard-links local_dir username@other_machine:/some_dir well... on both machines, the processor is running near idle, no heavy usage. I checked IO using process explorer on both machines, and that too is at normal levels (1~2 MB/s), so I can't see where the bottlenecks are, because network performance is aweful. I'm not going over 1MB/s... when a normal file copy using windows sharing achieves some ~10 MB/s.. What could be wrong?

    Read the article

  • Remote Desktop Software - TeamViewer comparison?

    - by Martin
    Preliminary Note: After reading what I wrote below, I would like to stress that this ain't a TeamViewer ad. It's just that all other tools that I checkked online seem to miss one feature or the other. :-) OK, so I'm currently trying to get a picture of available solutions for remote desktop software. I have found (through personal usage) that TeamViewer pretty much ticks all boxes that I personally would want from any remoting tool. (Specifically it's setup is amazingly trivial.) It supports a wide range of platforms and it's even free for private use, so I'm really quite OK with it. I would be interested if anyone knows of other tools that ticks as many boxes as TeamViewer seems to do.

    Read the article

  • 250k connections for comet with node.js

    - by Nenad
    How to implement node.js to be able to handle 250k connections as comet server (client side we use socket.io)? Would the use of nginx as proxy/loadbalancer be the right solution? Or will HA-Proxy be the better way? Has anyone real world experience with 100k+ connections and can share his setup? Would a setup like this be the right one (Quad core CPU per server - start 4 Instances of node.js per Server?): nginx (as proxy / load balancing server) / | \ / | \ / | \ / | \ node server #1 node server #2 node server #3 4 instances 4 instances 4 instances

    Read the article

  • RAID 1 not performing as expected

    - by Faken
    I recently bought a new 320Gb hard drive for my computer to set up RAID 1 on it for some added security. Installation went as smooth as could possibly be (plug in power, plug in data cable, start up computer, Intel software recognized new drive, right click create RAID 1, done!). However, for some inexplicable reason, I seem to have strange test results when using BENCH32. On my old configuration, a single 7200 rpm drive, I achieved about 60 MB/s write and 70 MB/s read. With a new RAID 1 configuration, I would expect the write to be slightly diminished but read to be significantly improved (though not exactly double speed). However, with the new configuration, I am getting 90 MB/s write and only about 80 MB/s read. I should NOT be getting improved write performance, especially NOT better than read! What's going on? My system setup is: q6600 2.4ghz CPU 4Gb DDR2 667mhz RAM on board Intel ICH9R "RAID chip" 2x Seagate 7200 RPM 320GB drives in RAID 1 Widows 7 home premium 64-bit

    Read the article

  • memtest incorrectly recognizes my RAM

    - by Brendan Abel
    I recently built a computer and randomly got a couple blue screens. I've run memtest and one of the memory sticks consistently throws memtest errors, while the other does not. The odd part is, memtest lists the following settings for my RAM: RAM: 535 MHz DDR 107 / CAS 2.5-1-3-1 DDR1 128 bits But my RAM is DDR3 1600? Memtest also lists my cpu as AMD K8, even though it's K10. I've probably going to RMA the ram stick, but I just wanted to see if anyone had any insight into the weird memtest stats.

    Read the article

  • timeout with apache & php w/ each virtual host has his own user process

    - by acemtp
    I have 10 unix users in /home/. Each user is for a specific subdomain for example user www in /home/www/public_html is for www.mywebsite. blog in /home/blog/public_html is for blog.mywebsite. 90% is php and 10% ror for the moment i use apache + fastcgi that use SuexecUserGroup to setup the process with the good user. it seems to works but i have a strange behavior where after a few hours/days, the server stop answering (timeout) but the cpu load is still very low (it's a big server), the apache status display lot of "W" Sending Reply states but there's still 50 idle workers so it should be able to answer. in the older server (lot of slower) we add only one user and using mod_php and we never had this issue. is there another way to do that without fastcgi and SuexecUserGroup or do you know what's going wrong?

    Read the article

  • What free OS should I use on my VPS?

    - by earlz
    Hello, I looked a bit but didn't see any duplicate of this so my question is which free(open source) OS do you use on servers and why do you use that OS? Background I have a VPS at Linode. There is a broad range of options for which OS I can put on it including both 32 and 64bit OSs. I just use it to run my small blog and for hosting random files. It's very low traffic. I have been using 64bit Arch Linux on my VPS and though I love the OS for general usage, for a server the constant breakage is troublesome. So I'm considering trying something new and am looking for suggestions.

    Read the article

  • teamviewer display is slow to refresh

    - by brunoais
    I'm using teamviewer from time to time to connect my portable computer with my desktop computer when I need to check on something (personal use). One of the main things I've been noticing is that it is quite slow transfering the screen updates that keep happening. This happens more frequently when I'm moving full windows or when I open a window or when watching a small movie clip. I've tested the lowest maximum p2p speed I ever got in the last week between both and it is the desktop's upload speed of 6MB/s with the ping of 40ms (usually ~15 ms). With this I was expecting to have very sharp image and fast transfer speeds which is not what is happening. Just to clarify, both computer's individual core's CPU is not reaching its peak (25%) while teamviewer is active, so the encryption and decryption is not the cause. Why my connection between both computers so slow?

    Read the article

  • MySQL Locking Up

    - by Ian
    I've got a innodb table that gets a lot of reads and almost no writes (like, 1 write for every 400,000 reads approx). I'm running into a pretty big problem though when I do INSERT into the table. MySQL completely locks up. It uses 100% cpu, and every single other table (in other databases even) have their statuses set to "Locked" until the INSERT is done. This is a big problem because MySQL stays locked up for up to 4 minutes. I'm using version 5.1.47 (rpm from mysql.com). Any ideas?

    Read the article

  • How do I associate server traffic to a domain hosted on that server?

    - by morley
    I have three or four Linux servers, each of which hosts anywhere from 5 to 50 domains. Each domain has its own folder: /www/projectname/web/ Logs go in: /www/projectname/log However, if there's a traffic spike (or, as I see it on my end, a memory usage spike), I'm not sure how to figure out which domain is responsible for the traffic without running tail -f on each of the projects and making an educated guess based on how fast things scroll. There's got to be a better way! There probably is, but I haven't seen it. And the last time I checked, bandwidth monitors only report system-wide load. So if anyone knows how to do this the right way, please let me know. Thanks!

    Read the article

  • How can I throttle the bandwidth consumed by Windows Automatic Updates?

    - by eleven81
    We have many Windows XP computers sharing one connection to the internet. These machines are set to download all available automatic updates and then prompt the user to install them. Whenever Patch Tuesday rolls around, our internet usage pegs out, and remains that way for most of the day, and sometimes into the following Wednesday. This hurts! I still want the machines to start to download the updates as soon as they are available, but if it takes until Thursday or Friday before the last updates are downloaded, that's still better than the latency and dropped connections we are seeing now as a result of the internet connection bottleneck. What can I do to throttle back how rapidly each machine downloads the updates, while still having them all start the download process as soon as the updates are available? I have no desire to run a WSUS server. Also, the internet connection is more than enough, whenever there are no updates to download.

    Read the article

< Previous Page | 241 242 243 244 245 246 247 248 249 250 251 252  | Next Page >