Search Results

Search found 755 results on 31 pages for 'acer'.

Page 26/31 | < Previous Page | 22 23 24 25 26 27 28 29 30 31  | Next Page >

• Can I replace my notebook's fan without replacing the heat sink?

  - by kuzzooroo

  My laptop (Acer Travelmate 8204) has started making a grinding noise, which seems to be coming from the fan (not the hard drive). Some articles online mention replacing the fan, but others imply that one should replace both the fan and the heat sink. Does it make sense to replace the fan only? (addendum: does this procedure really take 3 hours for a noob, as this video implies? UPDATE: the fan certainly seems to be on the "top" layer when I open my laptop but some parts of it extend under other layers) Some additional info in response to comments: I have run MS scandisk on the hard drive a few times since the grinding started. It usually reports finding something or other but the computer's behavior doesn't change I'm pretty sure it's the fan based on where the noise is coming from. I employed the cardboard tube trick from the PC World article.

  Read the article

• Old Fglrx Driver - AMD Radeon HD 3200 - ubuntu won't start

  - by Yohannes

  I've been using Ubuntu 12.04 64 bit for about 2 weeks now and I installed the latest Fglrx driver (Graphics Card- AMD HD 3200, PC- Acer Aspire 5336, 4GB RAM, 500GB Harddrive). The problem is that sometimes video's lag and play out of sync sometimes the windows take long to show up after I've clicked them etc. After looking around I found a video on Youtube by Ubuntu help guy and in the video he recommended using an older driver if you have an older graphics card, his was about 4 years old (same as mine) and he used the 11.10 catalyst driver so I decided to try it. I removed the previous installation of the driver and then installed the 11.10 driver. However, when I restarted it instead of going to the GUI it goes to a terminal like window and asks for my login. Now its pretty clear I need to remove the old driver and go back to using the latest one. The only problem is I'm not sure where I saved the latest driver and in order to connect to the Internet I need to change /etc/resolv.conf (I use a static IP). So what should I do? Also anyone from personal experience, what propitiatory driver works best with my graphics card? As in the version. Thanks

  Read the article

• System stuttering caused by hard drive

  - by LukLed

  My system keeps freezing for about 1-2 second every time I try to do something. For example, when I enter URL in browser, it freezes and starts working after few seconds. It is probably related to hard drive. I installed HD tune and when benchmark is in progress, causing constant disk use, everything works fine in background, there are no lags. What can be the reason of this issue? My hardware is Acer Aspire 7740G-6969 running on Windows 7.

  Read the article

• Using onboard and pci-e graphics card at the same time

  - by Endle

  Hello wonderful people. I know there are several other posts with similar questions. I also know how to use Google. I also have read up on posts discussing bumblebee, crossfire, ati catylist and many other interesting topics. I would just like someone to give me advice on how to use the onboard and pci-e graphics at the same time. I know the computer is capable of doing this. It works in Windows. I can use the VGA and DVI onboard port and the HDMI port of the add on card all at the same time. Works great in Windows 7, In Ubuntu, it seems only one or the other will work. I can use any combination of two displays on either adapter: VGA and HDMI..HDMI and DVI..so forth and so on. I have started experimenting with xorg.conf files, but have not been able to get any of them to work. Here is my last attempt at writing an xorg.conf file: Section "ServerLayout" Identifier "X.org Configured" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" LeftOf "Screen0" Screen 2 "Screen2" LeftOf "Screen1" InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Device" Identifier "Onboard Video" Driver "radeon" BusID "PCI:01:05.0" EndSection Section "Device" Identifier "Graphics Card" Driver "radeon" BusID "PCI:02:00.0" EndSection Section "Monitor" Identifier "CRT2" Option "VendorName" "ViewSonic" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "DVI1" VendorName "ACR" ModelName "P224W" Option "DPMS" EndSection Section "Monitor" Identifier "DVI2" Option "VendorName" "Acer" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Screen" Identifier "Screen0" Device "Onboard Video" Monitor "CRT2" DefaultDepth 24 SubSection "Display" Depth 24 Modes "1280x1024" EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Graphics Card" Monitor "DVI1" DefaultDepth 24 SubSection "Display" Depth 24 Modes "1920x1080" EndSubSection

  Read the article

• Upgrading Windows 7 on a new Netbook - Problems

  - by Swaffle

  I know this seems like a repeat of a question but i didn't get a clear answer from reading the other questions so im going to ask mine and hope i hear back good news. I bought an Acer Aspire one netbook with windows 7 starter. I have a DVD of Windows 7 Professional(x86) from MSNDAA through my college but when i tried to install it, i was given an error saying that i could only upgrade through the "Windows Anytime Upgrade" Though, it only gives me the options of paying for an upgrade, which im not willing to do, or putting in an upgrade key. I have a legitimate product key for windows 7 but it does not work for upgrading and the DVD does not allow for it. Am i doing something wrong? is there another option? can i convert my product key to an upgrade key ? Im up for any option, windows 7 starter is pretty limited in its features...

  Read the article

• force connection using USB adapter

  - by James

  Hi all I am new to Linux, so even though this is probably a simple problem it remains unsolved after more then 3 hours of googling :-( I run running ubuntu 10.04 LTS on an Acer Aspire 5520G . the laptop has a wireless adapter, but since I wanted better range I got an Edimax EW-7711USN USB adapter. now , when running ifconfig I am able to see both adapters where as the laptop native adapter is listed as wlan0 and the usb adapter is listed as wlan1. but listing available networks from the wireless network applet , all the connection are listed under wlan0 , the usb adapter is costencly listed as disconnected. this is what I have been trying to do so far 1) ifconfig wlan0 down - I got disconnected from the net but still was not able to get the usb to connect 2) used the wireless connection dialog to connect to a hidden network with the usb adapter - I was able to connect to the network but with no Internet access 3) disable wireless using the laptop function button - both wireless adapters where disabled can anyone suggest a way to connect to to the wireless network using the USB adapter rather then the built in one ? Thanks

  Read the article

• SSD runs faster on Windows as compared to Linux [closed]

  - by wushugene

  Windows 7 seems to install, boot and run much smoother & faster than each the three linux distros I have recently tried (Ubuntu 12.04 unity, Linux mint 13 MATE, and Fedora 17 on gnome 3.4). Why am I facing bad performance in Linux? I have tweaked my Linux installs for the SSD (enabling trim, disabling swap, etc.) I'm using an Acer TravelMate with i5-2410m processor, intel hd 3000 graphics, 8 gigs of ram, and a 256 gb samsung 830 ssd. Edit: Boot times are 10-15 seconds slower, there is noticeable delay from login to fully loaded desktop, and in general does not appear to be as responsive as my old windows 7 install or the Linux guests I had running on it.

  Read the article

• AR242x / AR542x wireless card not working

  - by Pipan87

  My wifi worked perfect until I updated to the latest version of Ubuntu. Now I don't find any wireless connections at all. I have tried lots of guides on the internet but I can't get it to work. I did however start to work once after writing something I don't remember in Terminal, but after rebooting it stopped working again. Some info (don't know if you need more to help): 01:00.0 Ethernet controller: Atheros Communications AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0) Subsystem: Acer Incorporated [ALI] Device 022c Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at 55200000 (64-bit, non-prefetchable) [size=256K] I/O ports at 3000 [size=128] Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [58] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [180] Device Serial Number ff-93-2e-de-00-23-8b-ff Kernel driver in use: ATL1E Kernel modules: atl1e 02:00.0 Ethernet controller: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Foxconn International, Inc. Device e00d Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at 54100000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Kernel driver in use: ath5k Kernel modules: ath5k

  Read the article

• Cannot get script to run at startup (tried all the simple answers)

  - by Carey Head

  I have Ubuntu Desktop 12.04 LTS running great on an older Acer desktop. I want to use this machine as an in-home server for hosting Minecraft. The command to start the Minecraft server is java -Xmx1024M -Xms1024M -jar minecraft_server.jar nogui and that works great when I cd into the correct directory and execute the above. I created a script to do this: #!/bin/bash cd /home/myuser/minecraft-server1 java -Xmx1024M -Xms1024M -jar minecraft_server.jar nogui & cd /home/myuser/minecraft-server2 java -Xmx1024M -Xms1024M -jar minecraft_server.jar nogui & exit 0 I made this .sh file executable, and it too runs great when I start it manually from the terminal. The problem I'm having is getting these to execute at startup. I have my user account on this machine to auto login. I have tried the following: Adding the following to "Startup Applications" : sh /home/myuser/myscript.sh (Nothing happens on reboot) Adding the same to /etc/rc.local (Nothing happens on reboot). I even tested this one by running /etc/rc.local from the terminal, and it executed great. Just not at boot/auto login Added the lines from the script directly to rc.local (Nothing happens on reboot). I can't help but think that there's something I'm missing. The script executes great when run manually, but will not run at boot/auto login. Many thanks in advance.

  Read the article

• Does a hard drive "working hard", i.e. when defragmenting or otherwise continuously active, significantly affect a laptop's temperature?

  - by Marko

  Trying to diagnose and fix an overheating Acer 5735 laptop, running speedfan and doing general workload to try and cause the overheat conditions. I notice that windows xp is badly fragmented according to defraggler, at 58% fragmentation. So I defrag whilst watching the speedfan window, which was at the start reporting high warning style symbols for all of the sensors. After the defrag, I rebooted and ran a few programs, and even defraggler again and the sensors in speedfan all reported green i.e. not high. Wondering if there is a correlation between windows fragmentation causing the hard drive to work harder and produce more heat inside the laptop? dont want to just assume that the problems are resolved, so either speedfan is not accurate enough or fragmentation can lead to additional hard drive heat? All comments or suggestions welcome.

  Read the article

• If the WiFi switched on, should it disable the ethernet? [closed]

  - by Peter Stuart

  My friend having problems with her laptop and I am trying to help her via SMS. She can't get her laptop connected to the internet via the Ethernet connection and there is no WiFi in the area. Could it be because her WiFi is switch on, she is using an acer aspire. If she manually switches it off could that allow the ethernet connecttion to work? Or is it a missing driver? The cable works fine as her someone else tried it. Thanks Peter

  Read the article

• Wired connection not working

  - by YokoBlac

  I am using a Acer Aspire One. Here is the Ubuntu Wiki Page about my computer. I have a working wireless connection however when I plug a cat5 (Ethernet) cable in the lights flicker on the computer, but then nothing happens. Output of iconfig: eth0 Link encap:Ethernet HWaddr 00:1e:68:96:1a:6b inet6 addr: fe80::21e:68ff:fe96:1a6b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:43 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2622 (2.6 KB) TX bytes:936 (936.0 B) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) wlan0 Link encap:Ethernet HWaddr 00:22:68:92:7f:36 inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:68ff:fe92:7f36/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5702 errors:0 dropped:0 overruns:0 frame:0 TX packets:5284 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4117327 (4.1 MB) TX bytes:936709 (936.7 KB) Any understanding of this output is greatly appreciated.

  Read the article

• no boot option after install ubuntu 12.04 LTS using cd

  - by utamaku

  im facing a problem. after installing Ubuntu 12.04 LTS using boot from CD, when reboot there is no boot option to choose the OS. i directly log in to my Windows 7. before this im having an issue with the 'nomodeset' if not mistaken. after tick [x] on the nomodeset, i can install my Ubuntu, and stuck again at choosing the partition. so i had done 2 partitions for ubuntu, 1 partition for ubuntu ( ext3, mount /) and the other 1 for swap. then i can proceed until finished the installation. and after the system want to reboot. it take some times and just stuck at the screen doing nothing. not rebooting at all. i force to shutdown then restart again then directly go into windows 7 without boot option. in win7 the partitions for ubuntu is gone. i had tried the boot-repair thing and still doesn't help. it just show up the _ (terminal thing i guess). i typed boot repair and still the same. im using acer aspire 4736z. please anybody help me with this issue.

  Read the article

• How to get rid of disturbance on LCD monitor?

  - by Uday Kanth

  I have an Acer G195HQL LCD monitor and recently I've been noticing a lot of disturbance on the screen. They appear to be like flickering horizontal white lines. These lines are more apparent on dark backgrounds like grey/black. The curious thing is that, the intensity of these lines increases and decreases with no specific pattern. The disturbance temporarily goes away when I detach and re-attach the VGA cable at the CPU end. My speakers are magnetically shielded, but the problem persists even when I turn them off. I don't know what to do and this is really annoying me. Is it possible that my monitor is failing? Or is there anything I should check?

  Read the article

• Windows 7 formatting HD

  - by Rick

  I have an Acer Aspire 5610 that I am trying to put an Operating System back on. I am trying to install windows 7 32-bit and it will not go through the install. Not sure why. I am now trying to reformat the hard drive and start with a fresh formatted HD. No other partitions. The problem is that the install disk is not doing the format it is giving me an error. The error is 0x8007045d. I am at a loss. This is the first time running into this issue. Please Help.

  Read the article

• virtual machines: optimal host os to run Windows XP guest os?

  - by user61132

  My department doesn't have the budget to upgrade my ailing Dell D620 laptop. However, I do have the option to buy my own personal computer, then use my company-issued ISO image to run Windows XP as my guest os using virtualbox or vmware. Therefore, last month, I bought an Acer AX3910-U3012 desktop that had Windows 7 as the host os (and 8G RAM). In short, I was disappointed with the performance while trying to run WinXP as the guest os. (It didn't perform much better than my laptop.) Just wondering what the optimal host os would be for running Windows XP as the guest os? (No, I can't use my company-issued ISO image to build the os for my personal computer.) FWIW, I'm willing to spend up to $2k if it's REALLY worth it, but would prefer to spend no more than $1k. Also, in an effort to cut costs, I'd prefer buy a desktop instead of a laptop. Thanks for any/all feedback.

  Read the article

• Is my Power Supply Unit fried?

  - by Rob

  So my laptop just started smoking where I plug my charger in. I run a netbook, the Acer Aspire One. My charger won't charge it, because when I plug my charger into the netbook, the charging light that indicates the netbook is receiving power turns off. Is there anything I can do to troubleshoot where the problem is and what should I do now? Is just my charger fried and should I replace it. Or could there also be a problem with my netbook and do I need to look for other problems?

  Read the article

• Operating system not found after downloading skin pack

  - by 8BitSensei

  My brother has downloaded a executable file from Skin Pack — I believe it was the Mountain Lion IO6 skin pack. He's using an Acer Aspire 553G. And now his operating system won't start (Windows 7). It gets to the BIOS and then goes to load up the OS but the screen goes blank and it just goes back to the BIOS over and over again. He decided to play with the bootup settings and tried different options and got the error message "Operating System not found." Does anyone have any idea how to solve this?

  Read the article

• Oneric Aspire One. After latest 11.10 update to Linux 3.0.0-9 boot hangs at staement "Starting Bluetooth"

  - by hevh

  I have today updated the version of Linux on Ubuntu on my Acer Aspire One. The boot hangs on the statement "Starting Bluetooth". Help please!! EDIT1: I get the grub menu when I start the netbook and it doesn´t matter which version of linux I choose the resulkt is the same. It gets as far as the Ubuntu spash screen then drops into command line mode then hangs on the line "Starting Bluetooth". I can log in and have tried various forms of the apt-get command to fix the system but with no result. I do not need bluetooth at the moment and so could remove the application if I knew how. (have tried apt-get remove bluez). When I use the command sudo apt-get -f install I get an error message saying "There's not enough space in /var/lib/mysql/" folowed by several other error messages. I have spent some time looking for similar problems and solutions using google but so far got to nothing to help. Thanks EDIT2: I have since discovered when running Knoppix or slitaz from a usb stick that the file managers report the hard disc as having no space. However GPARTED reports it as having 3.69gb. I do recall making space on the hard drive by deleting some old files and emptying trash whilst the update was running; perhaps its related. Any suggestions for how I can recover the apparently lost space from hard disc without losing the data. I have backups of the actual data but do not wnat to lose the applcations configuration. Thanks Kev

  Read the article

• Internal SATA hard disk shows up as removable device on Windows 7

  - by neutron80k

  I am running Windows 7 on an Acer Aspire M7720 with three internal SATA drives; drive #2 and #3 are on a removable HDD rack. Drive #3 (on the second removable HDD rack) shows up as removable device in the system tray. If I take drive #3 and put it in the first rack, it shows up as an internal drive. If I put any other drive in the second removable rack, that drive is also shown as removable device. I would like to fix that so that the drive in the second removable rack also is listed as internal drive. Since this seems to be independent of the actual drive in the rack, I checked the BIOS, but that third SATA port uses the same configuration as the second rack. So far, I could not find a solution for this problem (it's really more an annoyance than a problem), any ideas are welcome.

  Read the article

• My sound is not working, so I'm going to reinstall FYI [closed]

  - by fer

  I've had trouble getting the sound to work in Ubuntu 12.04 I'm running an Acer Aspire 5739g laptop. This is using a clean install. This wasn't a problem when ubuntu first installed. Rather, it was when I ran the updates that it stopped working. I already tried the suggestions on the ubuntu sites and other similar queries, and they haven't fixed it. Something in the updates is making my sound not work. Edit: It turns out that this might be a bug (the sound issue, first paragraph). After reinstall, it happened again (it's not caused by updates at all, or any software, because I fixed it now w/o reinstall). It seems like I replicated it as follows: I changed auto-hide in the behavior tab of Appearance settings by turning it on, and setting the sensitivity to below the recommended setting. Then instead of restarting, I just logged out and back in. The sound stopped working again. I set the behavior settings to default, restarted, and now it's back to normal. Not sure if it's due to only logging out (and not restarting) or b/c I set my sensitivity to a low setting. Not sure if this helps anyone, but thought I'd mention it.

  Read the article

• Notebook display not working properly

  - by jfcfar

  I have an old Acer TM4001 notebook. If the laptop is powered-off, with the lid closed, when I power it on, it generally works. Then, without touching anything, if I reboot the computer the internal display wil not work anymore. To make it working again I need to shut down the pc, close and reopen the lid and then turn it on. If I close and reopen the lid if it is not working after power the pc on, it won't work. When the screen is working, closing and opening it has no effect (the data cable seems ok). The external monitor always works as expected: If the internal display is not detected, the external will be the main (and only) display. This is not OS-related. When the screen is not working I cannot see the POST. What could be the cause for this?

  Read the article

• Reset disk does not work for different model of computer

  - by dato

  I've created a reset USB disk on my HP computer, with Windows 7 Ultimate 32-bit, and it works fine. However, it does not work for Acer computers (notebooks too), so what is the problem here? I've have created it for the same user named user, and the password is exactly the same as well. Is it possible to show the language bar with a keyboard shortcut at the logon screen in Windows 7? I know I can do it through Control Panel, but I can't log into the system. When I click Reset Passwword, it shows me my USB flash drive and says that the password hint is on this USB drive. Then I click Next and type the new passwword, then confirm this new password, but an error dialog is shown. It says that an error occured when trying to change the password for this user-

  Read the article

• Blank screen on laptop after replacement

  - by Mark

  I have an Acer Aspire 5332 laptop, running Windows 7 home premium 32bit. My screen broke, but the particular screen (LED) are no longer made so I bought a CCFL one with a new converter which has proven to be compatible according to the supplier. When I first booted the screen went blank just after the Windows logo was displayed. I suspected a driver issue, so booted in safe mode without any problems, disabled the display adapter (Intel 4 series express family) and it booted up fine. So I guess the screen is not compatible with the display adapter. The driver version is 8.15.10.1892. I tried updating from the Intel site, but it saying it cannot (something to do with manufacturer specific). The supplier is not willing to take it back, so I'm down £60 (UK). I can use it with the adapter disabled, but the quality is bad and I cannnot play video, etc. Any help appreciated.

  Read the article

• Updating GeForce 9200 driver on Vista (64-bit) yields installer failed

  - by weka

  OK, so I have a Windows Vista... more specifically this: http://www.newegg.com/Product/Product.aspx?Item=N82E16883103182 a Acer Aspire AX3200-U3600A Desktop. I have DirectX 11 and I am trying to update my drivers... During the update of the latest one: GeForce 306.23 Driver my screen flashes a bit and goes black. This is standard when updating GRAPHIC DRIVERS. Then... my screen shifts 50 pixels or so to the left... OFFSCREEN. Not even Auto Image Adjust will fix the screen back... Then after that happens, I get this: Help, please? I just want to update my graphic drivers....

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31  | Next Page >