Search Results

Search found 23946 results on 958 pages for 'remote computer'.

Page 260/958 | < Previous Page | 256 257 258 259 260 261 262 263 264 265 266 267  | Next Page >

• Dell Inspiron/Windows Vista sleep/hibernate issue

  - by sarge

  When I hit the sleep button in Windows the computer looks like it's going into Sleep mode but a few seconds later it's restarted, and stops with this error message: internal hard disk drive not found To resolve this issue, try to reseat the drive. No bootable devices--strike F1 to retry boot, F2 for setup utility Press F5 to run onboard diagnostics. The computer is running Windows Vista (SP2) and I have installed all available Windows Updates and the latest manufacturer drivers. I have already tried to reseated the drive, ran the onboard diagnostics and there were no errors. I have changed the power settings for all devices where it's available so that they are not allowed to wake up the computer. Any ideas?

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state [closed]

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results.

  Read the article

• Preparing a new physical system with VMWare

  - by Max

  I need to create a new installation of Windows, but at the same time I need this computer. So I decided to create a new physical disk from within VMWare, install windows/drivers/software and then just replace the HDD in the computer. I've bought a new HDD, split it into two partions and installed Windows 7 using the VMWare's ability to use phusical disks. I can see the windows files and directories that have been created on this partition, but when I'm replacing the HDD in the host machine it cannot boot from it. Why is that? Is it at all possible to create a bootable physical disk with VMWare or I should create a virtual disk and then use some HDD imaging tool to copy the HDD image to a physical disk? Maybe there's a better way of installing a new system and working on the computer at the same time?

  Read the article

• Which game logic should run when doing prediction for PNP state updates

  - by spaceOwl

  We are writing a multiplayer game, where each game client (player) is responsible for sending state updates regarding its "owned" objects to other players. Each message that arrives to other (remote) clients is processed as such: Figure out when the message was sent. Create a diff between NOW and that time. Run game specific logic to bring the received state to "current" time. I am wondering which sort of logic should execute as part of step #3 ? Our game is composed of a physical update (position, speed, acceleration, etc) and many other components that can update an object's state and occur regularly (locally). There's a trade off here - Getting the new state quickly or remaining "faithful" to the true state representation and executing the whole thing to predict the "true" state when receiving state updates from remote clients. Which one is recommended to be used? and why?

  Read the article

• Dealing with an Idiot [closed]

  - by inspectorG4dget

  I'm a 4th year University Computer Science student, and I have this problem, that I don't seem to be able to find a straight answer to: As a 4th year computer science student, I spend more time in the computer lab on campus, than even my own home. This means that getting along with everyone else here is very important to me. In most cases, this is not an issue because my interactions with almost all the people here fall into one of the following categories: Let me help you, junior Hi fellow student in a course I'm taking, I'm having trouble with this assignment question. Can you give me a hint as to how you solved it? Hi fellow student in a course I'm taking, This is how I solved the problem that you're stuck on. Hope it helps Hi fellow student, I noticed that you're working on a project, using a library that I'm interested in. Can we setup a time so I can learn about this library from you? This model of interaction works very well for me. However, there is one fellow student, who manages to make my life hell beyond all of this (his name is not important, let's just call him "Sam"). He seems to be always (pardon my crass description) high and completely unwilling to contribute to a constructive, academic conversation. He's a pretty smart guy, but just comes across as (I hate to say something like this about a fellow student, but) an imbecile. He also has ignorant opinions on important topics, some of which pertain to my specialization (AI, NLP, etc), and when I try to explain to him why he's wrong, all he does is insult me and put me in a foul mood. I have tried ignoring him (sitting somewhere else in the lab, headphones, etc), but he seems to like doing this because he approaches me and no amount of "leave me alone" seems to do the trick. Can anyone please suggest to me how to deal with this man in a civil way? Thank you

  Read the article

• How do I mount my Android phone?

  - by Amanda

  I'm puzzled because my phone used to just appear when I plugged it in. It doesn't anymore and The development options are definitely set to allow USB debugging. The phone is charging via USB but doesn't appear in lsusb [0 amanda@luna android-sdk-linux_86]$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 17ef:4807 Lenovo UVC Camera Bus 003 Device 012: ID 413c:1003 Dell Computer Corp. Keyboard Hub Bus 003 Device 003: ID 08ff:2810 AuthenTec, Inc. AES2810 Bus 003 Device 013: ID 413c:2010 Dell Computer Corp. Keyboard Bus 003 Device 014: ID 046d:c001 Logitech, Inc. N48/M-BB48 [FirstMouse Plus] adb devices -l shows nothing. In my Wireless and Network settings I changed the USB connection settings to "Mass storage" -- they were set to "Ask on connection" though I definitely wasn't getting asked. I don't get any Click here to connect via USB alert either. I'm not even sure whether the issue is my phone or my computer. It seems odd that it isn't even appearing in lsusb Not for nothing, the thumb drive on my keyring also does not appear in lsusb -- I've tried both in a bunch of different ports. I kind of assume the thumb drive is just borked, but it could be my OS.

  Read the article

• Windows 7 sata disk not recognized after wake up from sleep state

  - by Gabber

  My windows 7 x64 PC/server worked fine until I installed a brand new seagate SATA hard disk (2 TB). My first disk was a IDE Maxtor (250 GB). I tried to use it as a secondary drive leaving the maxtor as primary and, when I put the computer in sleep state, on wake-up the SATA disk is not recognized anymore until next reboot. Now I'm trying to set it as primary disk (I copied the old HD contents with HD clone), when the computer goes in sleep state, on wake up it doesn't see the disc thus causing my system to crash. I tried the following: BIOS update (Asus M2V motherboard) but the situation worsened as the system didn't wake up from the sleep (with both my HD's) Reinstalling the drivers Bios changes Microsoft Hotfix KB977178 that seemed to address exactly my problem but gave me "The update is not applicable to your computer" message. Disabling hybrid sleep but no results. I also tried all the suggestions from this question Why doesn't Windows 7 wake up from sleep?. Still no results.

  Read the article

• Acer Aspire PC locked up and won't re-start

  - by Jim Scott

  Vista Home Premium locked up on 5/12/10 while on a website and could not get to 'control-alt-delete.' Mouse locked, too. On/off switch would not work (stayed lit) so I unplugged the power cord. When I tried to re-start the computer I could hear a fan running but it would not boot up, nothing on the monitor and no lights on the keyboard. O/S was preloaded so I do not have a boot disk.I tried pressing F1, F2 and F11 and also with monitor off but nothing worked. Computer has not been been moved or abused so all internal connections should be fine. Have updated Windows Vista Home Premium regularly and also updated Avira anti virus and anti malware programs regularly. Using Firefox and Vista Home Premium O/S. Computer is 2 years old and was purchased new from Best Buy.

  Read the article

• How do install Ubuntu from a USB stick?

  - by Sophia

  When I go to the boot menu on my computer and select USB stick, the screen goes black and there comes a flickering underline. Like I could write something. But I can't. Whatever I push, nothing happens. Except the PrintScrn/SysRq button. When I push it, mu computer beeps. I get no choose menu. Nothing. I found out the usb stick is in msdos format. So what format should I use and how can I format it? I am not a computer geek who knows everything. I'm just a beginner. And only 16 years old. I've got a new problem. The screen isn't black anymore. Now there comes an error message: SYSLINUX 4.04 CHS 20110518 Copyright (C) 1994-2011 H.Peter Anvin et al ERROR:No configurationfile found No DEFAULT or UI configuration directive found! boot: And when I write something: boot:example Could not find kernel image:example boot: Why does this fail all the time? ps. I'm using Ubuntu Oneiric 11.10.

  Read the article

• "MAS SMS-CDMA" Bluetooth service

  - by TuxRug

  I have my phone (LG Rumor Touch on Sprint) connected to my Windows 7 computer by Bluetooth. Usually, one of the services is unidentified and no driver is installed. Occasionally I have an issue that is solved by removing and re-pairing my phone with my computer. The last few times I have paired my computer and phone, the unidentified service was found and installed, as "MAS SMS-CDMA". It sounds like an interface that allows sending and reading SMS messages via Bluetooth. However, there is no software available from Sprint or LG that I have found that offers such functionality. Searching Google for "MAS SMS-CMDA" (with quotes) did not provide anything useful, only what appear to be CMDA information written in Spanish. What can I use this service for, and how do I use it?

  Read the article

• Customizing the windows server 2008 RDP login screen possible?

  - by moontear

  Hi, I'm working with RDP sessions quite frequently. As we work in teams and all use the same user account on a particular computer (I know...) I was wondering if there was a way to display from which computer (hostname, computername) the person is connecting. The login screen I get when two users are already connected looks like this (german): I'd love it, if the screen would display from where the logged in user is connecting e.g. "COMPUTER\user connected from MYCOMPUTERNAME". This way I would know whom to ask to disconnect so I can hop onto the session. If I remember correctly the login screen looked different for previous Windows versions including this connection information. Any way I can easily enable this or is this just standard windows behavior and there is no way to tell from where the user is connecting (btw: Task Manager shows the computername of the connected user).

  Read the article

• Web Development - How to access custom host, defined in my hosts file, from another device in the same network

  - by Neara

  Ok, I hope i'll be able to explain the issue im experiencing. I'm working on a project, that has 2 parts: one takes all requests from usual localhost, the other handles requests from myhost.local. While trying to access both addresses from my computer, it works ok. But now i need to test myhost.local on mobile devices, connected to the same network. Usually i would just run server from my computer ip in the network: python manage.py runserver 10.0.0.8:8000 And then from any device, going to 10.0.0.8:8000 would show the project im working on. However, now accessing that ip address routes me straight to localhost. So, my question is how to access myhost.local from another device in same network? I don't want to change router settings, if that can be avoided, cos sometimes i work from places where i can't access router admin. Is there any network settings on my computer, that i can change to fix the routing to myhost.local w.o losing access to localhost as well?

  Read the article

• When connected through a router, a new gateway appears, and I lose my internet connection.

  - by idan315

  I have two computers connected to a router, connected to my ADSL modem by PPPoE. One of those computrs use Windows XP, the other uses Windows 7. The computer using Windows 7 keeps getting limited or no connectivity, and I can't use it to connect to the internet. Connecting the computer to the modem without the router 'in the way' worked, and I was able to use the internet - which led me to believe that the problem is with my router. However, I have changed my router, and the problem persists. (Just to be clear: the computer using Windows XP can connect to the internet without any problem). This entire question is about the PC using Windows 7. The only symptom of this problem is that when I see my network devices, in addition to my router (which appears as "Network 4", or something of the sort), I also see an "Unidentified Network". When using ipconfig to check the problem, I see a second gateway, with the IP 0.0.0.0, in addition to the IP of my router.

  Read the article

• Improve my System, Need some advice/suggestion

  - by Pennf0lio

  Processor: 2.40 gigahertz Intel Core2 Duo Board: ASUSTeK Computer INC. P5B-MX Memory: 2 Gb VideoCard: NVIDIA GeForce 7300 GT HDD: 80GB + 250GB both IDE Operating System: Windows 7 32bit Please give me some advice what to improve in my System. I mainly used it for Graphic Design (eg, Photoshop, Cinema4d, Illustrator, Flash). I was planning to increase my Memory adding 2 GB more, Pushing it to something like 4GB in total. But just found out that recently that I already have 2x2GB installed and should be 4GB in total. When I looked at the properties of my computer, It said "Installed Memory 2GB". I wonder why is that happening? Is the other ram broken?.. I never the computer casing since I bought. so I didn't realize that I already have 2 x 2gb ram. what can you advice. Thanks!

  Read the article

• balancing loudest and quietest speaker noises

  - by Dan

  It is hard for me to find the right volume for my computer to watch my dvd's on because it seems like most reasonable volumes become overwhelming at the loudest parts of a movie and it is hard to even make out the dialog at the quietest parts. I find I'm constantly adjusting the volume during the course of a movie. Are there ways to make the difference between the louds and the quiets not so extreme? (both computer related solutions and non-computer related solutions welcome). Like moving my speakers across the room and increasing the volume? or the opposite? Or would would the extremes be less noticeable if I used headphones? Are there movie players that might have more complex sound adjustment features? If there is a software solution out there for linux that would be great too. Thanks, Dan

  Read the article

• Automatically revert to laptop screen when external monitor unplugged

  - by Ryan

  I regularly use an external monitor with my laptop, so when I use it, I usually have the laptop screen disabled when the monitor is connected, and this seems to cause problems when the monitor is disconnected. If the monitor is connected while the laptop screen is disabled, I can't get the X session to show up at all: I can Ctrl+Alt+F1 to open a terminal, and that works fine.. ..but Ctrl+Alt+F7 does nothing. The display is blank, and stays blank. The same thing happens whether I put the computer to sleep with the monitor connected, or if I disconnect while the computer is still awake. Rebooting the computer fixes the issue, as does killing Xorg and starting it again, but both of those are sub-optimal since I lose my current session. I'm currently using the open source graphics driver (xserver-xorg-video-ati). This question looks like it might answer my question, but unfortunately hwinfo is no longer available in the apt repository. Is there a way with current tools to automatically detect when the external monitor is disconnected and switch to the laptop display?

  Read the article

• Webserver on a rotating server with NAT IP or changing IPs

  - by hpsoftware

  i would have to elaborate my questions so please have patience Explaining the logic. if you are familiar with logmein then it installs a client software on your computer then it kinda keeps tracks where you computer is as long as it's connected to internet. So you can always access your computer no matter where it is whatever it's IP is you just go to logmein.com and then you can just access it. Now what i am asking 1. Let's assume i have a website hosted on my laptop let's call it webserver. so then i move around i have a new IP sometime even on a hotel network is it possible to do something like what logmein does so i can keep moving around my Webserver to new IP but it has some local client or something which keeps updating my IP or something i am sure i would need a gateway server somewhere which is connected to my domain name via DNS so somebody accessing my website www.mywebsite.com goes to my main server then gets routed to my laptop which could be anywhere but my gateway server is able to communicate to my webserver I will keep updating the case description based on comments to make more sense. please have patience with me. Regards

  Read the article

• IP addresses not updating, but showing correctly in the DHCP Address Leases

  - by Bobby

  I first noticed this when I tried a RDP to wxp-38-shop and it connected me to the computer wxp-alvinm As you can see in the picture I pinged wxp-38-shop and it shows a different IP then whats given in the Address Leases page (w2k3 server). I tried to do ipconfig /flushdns on the server as well as the client computer, but it didn't update that way. If I do an ipconfig on wxp-38-shop is also shows 192.168.0.153, so why when I ping it from any other computer why would it be showing the wrong IP?

  Read the article

• Another Exchange 2003 to Exchange 2010 mail flow issue

  - by Ryan Roussel

  During a migration recently, we came across another internal mail routing issue.  The symptoms were identical to my previous post about Exchange internal mail routing.  Mail was flowing from 2010 to 2003, from 2010 to the internet, but not from 2003 to 2010.   I went through the normal check list looking at permissions, DNS, and the routing group connectors.  I verified that both servers listed in the routing group connectors were the routing master in their respective routing groups through the 2003 ESM.  I also verified that inheritable permissions were enabled for the Exchange 2003 server object in the schema.  No luck with either.   For my previous post about this issue in which inheritable permissions were the culprit: Exchange 2010, Exchange 2003 Mail Flow issue   And for Routing Group issues: Exchange 2007 Routing Group Connector Mayhem   I finally enabled logging on the SMTP virtual server on Exchange 2003 and the Default Receive Connector on 2010 and sent a few test e-mails where I found 2003 was having issues authenticating to 2010.  By default 2003 uses Exchange Server Authentication to communicate to 2010. The exact error was: 4.7.0 Temporary Authentication Failure which was found in the SMTP logs on the Exchange 2003 side   After scouring based on this error, I found the solution:   The Access this computer from the network user rights in the local computer policy on the Exchange 2010 server were changed from the default.  The network administrator had modified the Default Domain policy and changed this user right assignment to only list Domain Users.   The fix was to clear this setting in the Default Domain policy,  force gpupdate to refresh the group policy settings, then ensure the appropriate users and groups were listed.   This immediately fixed the problem and the Exchange 2003 server was able to route mail to the Exchange 2010 mailboxes.   The default user rights assignments for Access this computer from the network On Workstations and Servers: Administrators Backup Operators Power Users Users Everyone On Domain Controllers: Administrators Authenticated Users Everyone More can be found here: http://technet.microsoft.com/en-us/library/cc740196(WS.10).aspx

  Read the article

• Processor upgrade on a laptop vs. Ram upgrade. Also does ram always matter?

  - by Evan

  I have a Dell Inspiron 14r (N4110) with an Intel Core i3 and 4gb of ram. It runs very smoothly, however gaming on this laptop is very limited. This is mostly because of integrated graphics but i have seen a computer with a Core i5, and very similar specs otherwise, run games that the N4110 cannot. This other computer has integrated graphics and 6gb of ram. I am wondering whether upgrading ram or upgrading the processor make the most difference in performance. Which setup would get better performance, an i5 with 4gb of ram or an i3 with 8 gb of ram? (Both with integrated graphics) Also, is there a certain point at which you have too much ram for the computer to ever possibly use? For instance is there really any difference in performance between 8 gb and 16 gb of ram?

  Read the article

• Procedure entry point EncodePointer could not be located in kernel32.dll

  - by waanders

  I get this error when trying to run a program on a Windows computer: Because it's a Dutch Windows version it is in Dutch, but in English it would be something like "Procedure entry point EncodePointer could not be located in kernel32.dll". I've been looking for a solution on the net and I think it has something to do with SP's of Windows. This are the system settings: Does this mean I'm not using any Windows XP Service Pack? I'm working on this for someone else, it's an old computer, not connected to the internet. Should I connect the computer to the internet and install all Windows updates to solve the problem? No other solution?

  Read the article

• What's wrong with my MAC address?

  - by Shaul

  I have a D-Link DSL-2650U router, and exactly one computer on the network. For reasons of port forwarding I want to give my computer a static internal IP address, so that I don't take the chance of losing my NAT settings every time the computer reboots. So here's a screen shot that summarizes the entire problem: WTH is wrong with my MAC address? It's copied and pasted from the command prompt window! I tried editing out the dashes, but it still doesn't work. Am I doing something wrong, or is there a bug in the D-Link firmware?

  Read the article

• Serious voltage and temperature problems

  - by James Willson

  My computer has been acting up when I play games so I wanted to look into why. Issue 1: GPU Temp According to afterburner and speedfan my 8800GTX idles at 90 degrees and then when playing games shoots up to over 110C which is when my graphics basically starts to give rendering issues. Issue 2: CPU Temp Speedfan is saying my CPU temp is 83C idle but when I look at core temp it says core0 is at 35C and core1 is at 33C. Issue 3: Voltages This is what speedfan is saying for my voltages: Vcore1: 1.01V Vcore2: 1.90V +3.3V: 3.31V +5V: 4.95V +12V: 0.51V -12V: -16.80V -5V: -8.43V +5V 5.13V Vbat: 3.25V Vcore: 3.00V +3.3V: 3.20V These voltages, for lack of a better word, look f*cked. With all this happening, the computer runs ok under normal use. Is the software giving out incorrect readouts or instead should I immediately move the computer into another room before it explodes? P.s I would like to add this is a stock system. EVGA 8800GTX, E6850 CPU, 800W PSU

  Read the article

• Looking for an easier Skype video chat alternative

  - by Paul

  Is there any software 'easier to use' than Skype - ie to get a video conversation going you have to turn on the computer, make sure the speakers are turned on, make sure the web cam is connected, make sure you click answer with Video... I would like to buy a 'single red button' which does all of the above. - Any recommendations? Update @Eric Koslow comment My original question title was "Is there any software/hardware 'easier to use' than Skype?" So the answer is not necessarily a computer running a program, although it might be. I realise Skype makes a good attempt at helping to ensure speakers and web cam are working and helps you to sort them out if they are not, and for a person who isnt computer phobic this should be enough. However I am interested if there is anything available that is 'easier' than this - ie I'm looking for my 'single' red button. ie the mobile phone with video call maybe the closest answer so far, but I would prefer something as 'free' as Skype is.

  Read the article

• Detect damage done by virus

  - by user38471

  Hey, this morning after I went to college a virus infected my pc without any user interaction at my end. When I came home my computer was completely frozen and infected with lots of trojans. I have not typed anything important since returning so keys cannot be logged. However I want to know exactly when my computer crashed from the time of infection to see what could potentially be done remotely by a hacker. The virus my pc was diagonosed with was "fakespypro" http://www.microsoft.com/security/portal/Threat/Encyclopedia/Entry.aspx?Name=Win32%2fFakeSpypro on a fully updated windows 7 installation with firewall enabled. My computer was connected to an internal dorm room network, so probably that has had to do something with it. Any further information about how I could backtrace this virus infection or ways to discover what data might be stolen would be greatly appriciated.

  Read the article

< Previous Page | 256 257 258 259 260 261 262 263 264 265 266 267  | Next Page >