Search Results

Search found 7555 results on 303 pages for 'installing'.

Page 261/303 | < Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >

• Windows 7 Install: No drives were found

  - by Albert Bori

  I was building a computer for my wife with an older SATA hard drive that I had lying around, and when attempting to do a new install of Windows 7 on it, the installer says: "No drives were found. Click Load Driver to provide a mass storage driver for installation." I ran the diskpart command: list volume, and it showed up as "Raw". So, I formatted it to NTFS and then it showed up as a healthy drive in diskpart. I also ran check disk on it with no errors. Windows 7 installer STILL can't find the drive. As far as BIOS settings, I have tried "Native IDE", AHCI, and Both AHCI/IDE mode (SATA slots 0-2 AHCI, 3-4 IDE). I tried all combinations... still "no drives were found". At this point, I'm just scratching my head. Using the installation dos window, I can see and talk to the drive just fine, but the installer just doesn't see it at all. I've even written folders and files to the drive, and it still "can't be seen". Any help would be great. Items of interest: Motherboard model: Gigabyte GA-A75M-UD2H - BIOS Version F5 (latest) Hard drive model: 80GB Seagate Barracuda 7200.7 ST380817AS (no other drives) Installing Windows 7 using a FAT32 formatted USB Drive, which I've used for other installs

  Read the article

• Linux Mint Constantly freezing on Dell XPS L502X

  - by Josh

  I recently partitioned my hard drive to dual boot the existing Windows 7 with Linux Mint because I am tired of using Windows, especially the lack of terminal. I want to eventually remove Windows 7 and just run it from a VM within Linux Mint, but I want to make sure that I like the Mint before going all in. I ran Linux Mint on a VM inside Windows for a while, enjoyed it, and never had any issues with it. Since installing on my hard drive it has started freezing every 5-10 minutes, and the only way to get it back is to either power down, or close the lid and reopen once it sleeps. I've also tried running Ubuntu on dual boot in the past, and while it never froze, the battery life was terrible, and the fan was constantly running. I'm experiencing the same battery/fan problem with Mint, which doesn't make sense to me, as Linux should be lighter on the CPU than windows. If I had to guess I'd say it's probably a driver thing, with my video card or fan or something. My battery life in Windows is ~2 hours and its about 40 minutes in Linux. At this point, that is even if my laptop doesn't freeze before then. On a less important note, I also have an intel Centrino 6150 WiMax card that I'd like to be able to use, but that won't register on the Linux system either. I have tried downloading drivers for both of these, but neither have solved my problems. I'm definitely getting frustrated and am getting close to giving up on Linux even though I dread working on a Windows machine.

  Read the article

• Choose a VPN software on CentOs 6.5

  - by loyCossou

  We are installing a SMS gateway with Kannel, on a CentOs 6.5 server, which is supposed to connect via SMPP to our local operators. Kannel is working fine and no probleme there. Now 2 operators are asking to connect via a VPN for obvious security reasons; actually they asked for or VPN details so they can connect to it... Now, I am looking for a free VPN that I can setup and configure on our server... I saw Open VPN that I already started configuring, no issue... But just saw on Wikipedia (http://en.wikipedia.org/wiki/OpenVPN#Platforms) that OpenVPN is not compatible with other VPN packages. Now my question is: 1- I am absolutely new to VPN technologies. Is OpenVPN a good choice in my situation? 2- If I configure OpenVPN on my server, will it be possible to any client to connect to my server? 3- Anyone have any advice for me? Thank you for this great community.

  Read the article

• Power supply switch like stays off motherboard light turns on

  - by Sion

  I bought a computer at the thrift store yesterday. The computer powered on without any error beeps. Getting it back to the house determined that the CD and hard drive needed to be changed. Put in a populated hard drive to check, the computer turned on and seemed to function. Put in a new CD drive, and just put in a new Hard drive. I plugged it in to check and I noticed that the light for the power supply switch did not come on. But I did notice that the light on the motherboard is lit. and I could not turn the computer on. To help troubleshoot it I unplugged the CD and Hard drive. then re-plugged the power supply and switched it on and off. Nothing changed. Parts: Motherboard: Digital Home PSW DH deluxe Power Supply: FSP-Group FX700-GLN Did I accidentally unplug something while installing the hard drive? Is the Power supply fried somehow?

  Read the article

• Windows 8.1 in a VMWare Workstation 10 guest's mouse is missing, but only sometimes

  - by Rob Perkins

  I have VMWare Workstation 10 running on a Windows 7 machine, hosting a k guest OS. Before upgrading to WS 10 I was using version 9, and the Win8 guest OS ran without difficulty or error conditions. Since upgrading and installing the most current VMWare Tools inside the guest after upgrading to version 10, there are circumstances where the mouse pointer is not visible; the mouse position appears stuck at a screen location which is not the center of the virtualized display; and mouse click and scrolling events still get processed. Once this begins happening I have to reboot the host machine to get it to stop. (VMWare Tools 9.6.1 build-1378637 is what the WS 10 software installed) The problem seems to correlate with whether the mouse is captured during Win 8.1's bootup process, before control is passed to the login screen. If I explicitly click the mouse into the guest OS and move it slowly around while the system is booting, then I see the mouse after clicking to lift the first screen and expose the password prompt, and there is never a problem within the guest. If I don't do this during bootup, there is no mouse pointer, with the symptoms listed above. I have tried removing and reinstalling VMWare tools, and the other steps published for "mouse problems" from VMWare's chaotic troubleshooting database. The problem persists. Is there a setting in the virtual machine's configuration which could prevent this behavior?

  Read the article

• Centos iptables configuration for Wordpress and Gmail smtp

  - by Fabrizio

  Let me start off by saying that I'm a Centos newby, so all info, links and suggestions are very welcome! I recently set up a hosted server with Centos 6 and configured it as a webserver. The websites running on it are nothing special, just some low traffic projects. I tried to configure the server as default as possible, but I like it to be secure as well (no ftp, custom ssh port). Getting my Wordpress to run as desired, I'm running into some connection problems. 2 things are not working: installing plugins and updates through ssh2 (failed to connect to localhost:sshportnumber) sending emails from my site using the Gmail smtp (Failed to connect to server: Permission denied (13)) I have the feeling that these are both related to the iptables configuration, because I've tried everything else (I think). I tried opening up the firewall to accept traffic for ports 465 (gmail smtp) and ssh port (lets say this port is 8000), but both the issues remain. Ssh connections from the terminal are working fine though. After each change I tried implementing I restarted the iptables service. This is my iptables configuration (using vim): # Generated by iptables-save v1.4.7 on Sun Jun 1 13:20:20 2014 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 8000 -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 465 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited -A OUTPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A OUTPUT -o lo -j ACCEPT -A OUTPUT -p tcp -m tcp --dport 8000 -j ACCEPT -A OUTPUT -p tcp -m tcp --dport 465 -j ACCEPT COMMIT # Completed on Sun Jun 1 13:20:20 2014 Are there any (obvious) issues with my iptables setup considering the above mentioned issues? Saying that the firewall is doing exactly nothing in this state is also an answer... And again, if you have any other suggestions for me to increase security (considering the basic things I do with this box), I would love hear it, also the obvious ones! Thanks!

  Read the article

• Creating security permissions for a non-domain-member user in Windows Server 2008

  - by Overhed

  Hello everyone, I apologize in advance for incorrect use of terminology, as I'm not an IT person by trade. I'm doing some remote work via a VPN for a client and I need to add some DCOM Service security permissions for my remote user. Even though I'm on the VPN, the request for access to the DCOM service is using my PCs native user (and since I'm running Vista Home Premium it looks something like: PC-NAME\Username). The request for access comes back with access denied and I can not add this user to the security permissions as it "is not from a domain listed in the Select Location dialog box, and is therefore not valid". I'm pretty stuck and have no clue what kind of steps I need to do here. Any help would be appreciated, thanks in advance. EDIT: I have no control over what credentials are being passed in to the server by my computer. This scenario is occurring in an installation wizard that has a section which requests you point it to the machine running the "server" version of the software I'm installing (it then tries to invoke the relevant COM service, but my user does not have "Remove Activation Permissions" on that service, so I get request denied).

  Read the article

• Move a screen session back to its original PID

  - by cron410

  Installed McMyAdmin (minecraft manager) on Ubuntu 12.04 32 bit. Wrote my own service to start McMyAdmin (.net app running in Mono) in its own screen session, and be able to inject proper McMyAdmin commands into that session with the init.d script. Its been running great! Today, I decided to start installing a Source dedicated server (counterstrike pro mod) I determine its going to be a long download process so I quit the process and fire up a fresh screen session called "source". I paste the command in, but it has a space at the begining and bash complains of ignoring semaphores or some such. I detach and reattach the session. Its sliding like butter. I ctrl+a-d out of the session and start exploring the new folder structure and figure out where I need to place a symbolic link. I go to resume that screen and this is what I see: $screen -r source There are several suitable screens on 20091.source (12/02/12 22:59:53) (Detached) 19972.source (12/02/12 22:57:31) (Detached) 917.minecraft (11/30/12 15:30:37) (Attached) It appears I am connected to the minecraft screen?!?!?! So I attach to the other screens one at a time. minecraft is running in 19972.source and sourceds is running in 20091.source So how the hell did I move the minecraft process to another session called source and my main terminal is now "attached" to the minecraft screen? more: I just used exit to quit the putty session, then logged back in, its still the same. did that 3 more times and now the minecraft screen is gone and everything is acting as it should except, of course, for the session name and start time of the "new" minecraft screen. Should I just submit this as a bug for GNU screen?

  Read the article

• Turn computer into DAS (Direct Attached Storage)

  - by Damon

  Can we build a direct attached storage by taking a computer/server, adding an HBA, and installing some appropriate software? We would use Debian as a host OS for both the DAS and the server. If so, what software do we use? And do we simply need a HBA for the DAS and the Server? Or do we need more hardware? The goal is to use an older server that does not have enough room for drives but does have ECC memory, server processors, redundant power supplies, dual nics, etc. Then find any boxes, server or not, the key being having enough room for 8-12 drives, fans, etc. and turning them into a DAS; build two of these DAS's and have them connected to the server. Eventually we want to have two servers using DRBD and associated services like heartbeat and pace maker to create an HA setup for our server(s) but that will take a long time to configure since I have no experience with anything related to DRBD (yet) and have a learning curve I have to get past, not to mention the additional cost of more hardware (two servers vs one).

  Read the article

• Why would e-mail from our own domain not be forwarded to gmail

  - by netboffin

  To solve a problem with spam on our server we tried to forward e-mail from our dedicated server's mailserver(matrix smtp service) to gmail, but while most e-mails got through e-mail from our own domain all went missing. They weren't in the inbox or spam or anywhere else. We've had to go back to using the old system, which means my boss gets a huge amount of spam. We have a windows 2003 server with iis 6 and the matrix smtp service installed. I've toyed with the idea of installing a mail proxy like ASSP but it looks pretty complicated. We're hosting 20 domains on the server as well as our own which has an online shop whose payment system depends on email. I can't start playing around with complicated solutions when it could have disastrous consequences and I don't know enough to implement them safely. So my question has two parts: Part One: Why can't we forward e-mails from people using the same domain. If our domain was foobar.com then [email protected] can't receive from [email protected], but he can receive from everyone else. Part Two: Is there a really simple server side solution to spam that would work with matrix? For instance popfile?

  Read the article

• BSOD error 0x0000006B PROCESS1_INITIALIZATION_FAILED on boot

  - by DontCare4Free

  I reinstalled League of Legends because the patcher always gave me an error. However, out of complete stupidness I didn't uninstall the old installation first because I thought that it would simply replace the files. However, when the installer bar got to 100% it simply minimized. Then I closed the application from the task manager. I tried uninstalling it after a failed attempt to start it up. The same behavior as when I installed it. Then I tried reinstalling where it simply presented the InstallShield Modify/Repair/Remove menu and I selected repair. Nothing happened. Then I tried selecting Modify, then seeing that the only option (called DefaultFeature) was unchecked. Same behaviour as install/uninstall. After seeing that it still failed, I uninstalled again. And after that I deleted C:\Program Files (x86)\League of Legends manually. When I tried installing LoL again it still thought I had it, so I chose repair. This time something actually happened, but it installed the whole game to C:\Windows. Seeing what was going on I clicked cancel and then started it up to try uninstalling it. However, I got an error message about something not being registered and then the minimization to I decided to let it repair completely. Then I uninstalled it and it gave only the minimization. However, when I rebooted another application started up complaining about some library being absent. So I decided to do a system restore. After letting it complete I got a BSOD every time I tried starting up Windows normally or in safe mode. However, system recovery mode works, although the system recovery automatic repair does not fix it. After a bit of searching I found a Microsoft KB article about it (981833) and tried following the workaround instructions. Nothing happened. I am using Windows 7 Home Premium 64-bit and Ubuntu 10.04 LTS 64-bit installed with WUBI.

  Read the article

• Asus PCE-N53 11n N600 PCI-E Adapter on 3.x kernel

  - by CITguy

  Problem ASUS PCE-N53 wireless NIC doesn't work for latest versions of the linux kernel. How do I get it working on my system? (Note: I'm posting the answer I've found for others to use.) Installing Driver for Linux 3.x Kernel ASUS provides Linux drivers from their website, but it mentions that the driver supports "Linux Kernel 2.6.x", so it won't work without a some modifications to the driver code. Fortunately, an archlinux forum mentions similar problems and one user was able to create a patch for kernel 3.8.x that seems to work with kernel 3.11.x. Here's how I got it working: Prerequisites Ubuntu: sudo apt-get install build-essential Arch: sudo pacman -S base-devel Steps: 1. Download the driver from the ASUS website The download can be found under "Support Drivers & Tools". 2. Unzip the contents of the downloaded file cd into the new directory 3. Patch The arch forum mentions a 3.8 patch file that needs to be downloaded. Download rt5592sta_fix_64bit_3.8.patch to the current directory. tar -xvf {driver_source.tar.gz} cd into the directory created in previous step patch -p1 < ../rt5592sta_fix_64bit_3.8.patch 4. Compile NOTE: You will need to use sudo for it to compile properly. sudo make sudo make install sudo modprobe rt5592sta 5. Enjoy If all is well, you should now have a working card.

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  Hiya, I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• Ubuntu 12.10 64bit host reboots when trying to install any guest system using VirtualBox

  - by gts123

  I am having a really nasty problem with VirtualBox as everytime I try to install any guest OS(using ISO file as CD for installation media), the installation starts normally but as soon as it is about to start either installing to virtual hard drive or loading(e.g. as LiveFS) it causes the host system to reboot abruptly. Config is as below: Host system: Ubuntu 12.10 64bit - Intel® Core i7-2640M CPU @ 2.80GHz × 4 Virtualbox version: 4.1.18_Ubuntu r78361 Guest OS systems tried: 32bit version of FreeBSD 9, Debian 6, Tails 0.14 VM setup Tried to have the minimal setup necessary just in case it would avoid for each system to make sure I'd avoid conflicts, but to no avail. I've tried different values and combinations of the below but the problem still persists: Shared Clipboard: Disabled Show in fullscreen/seamless: Disabled Remember runtime changes: DIsabled Base Memory: 2048 MB Chipset: PIIX3 IO APIC: Disabled EFI: Disabled Absolute Pointing device: Disabled Processor(s): 1 CPU PAE/NX: Disabled VT-x/AMD-V: Disabled Video Memory: 12 MB 3d/2d acceleration: Disabled Storage IDE COntroller: PIIX3 (same as chipset instead of PIIX4) Use host I/O cache: No Audio: disabled Network adapter: NAT USB controller: disabled No shared folder Also another sideeffect of the reboot is that it appears that it does not log any information in the error log files; not making things any easier. Please help.

  Read the article

• Spotlight has stopped indexing/returning anything in /Applications

  - by pra

  After a recent kernel panic & restart, Spotlight no longer seems to know anything about the files under my /Applications folder. I used to launch Safari.app, Opera.app, Textedit.app, etc via Spotlight as a matter of routine. Now, I get "No results found" for all of them (except Textedit.app, which launches a demo text editor from a Qt installation). The programs are still there & still launch directly from Finder. I've already run disk utility & verified the disk, no issues. I repaired disk permissions, which made several changes, but to no effect. Is there anything else I can do, short of re-installing MacOS? Update: I already verified that "Applications" was still checked in my Spotlight preferences. It was still returning applications located elsewhere (the Qt textedit sample app), so that shouldn't have been the issue. A few hours later it resolved itself; I guess there's a background process running on some interval.

  Read the article

• Adjust output Brightness/Gamma/Colors in Gnome

  - by Mikee

  We have a desktop system running Ubuntu 8.04.4, and it is connected to a standard desktop LCD monitor. Unfortunately, in 8.04.4, the brightness of the image is cranked way up. It appears to be a graphics driver issue. Unfortunately, installing a newer GPU driver for this Intel GPU is very difficult to do. So, I am looking for a software (or config file?) solution to achieve this. Note: Ubuntu 9.10 and higher do not exhibit this issue, so this is not a hardware problem. Note: VNC-ing to this machine from another does not exhibit this issue either. Also, I installed "DisplayCalibrator.app", and it does not work very well (the app comes up, but the contents of the window are blank). Is there anything that I can add to the xorg.conf file to correct this issue? Also, this solution: http://superuser.com/questions/96539/adjust-contrast-and-brightness-in-ubuntu did not resove my issue. Thank you all for the help!

  Read the article

• How do I set up dual monitors on Kubuntu 10.04 using the latest nVidia drivers with a 9800M video ca

  - by NoCatharsis

  I'm a Linux newb so please try to keep the lingo low-key. I installed the latest nVidia drivers on my laptop using the 9800M card. The laptop is a Gateway P-7805u and I'm connected to the second monitor using VGA. Also, before installing the nVidia drivers (and just using the basic drivers included with Kubuntu 10.04), basic dual monitor support worked, except I could not enable compositing features for some reason. So I thought the proprietary drivers would fix this. Several issues have arisen since installation: 1) I've clicked through all of the display settings to activate the second screen with absolutely no change. 2) When I try to apply settings and Save Configuration as the nVidia help suggests, I am told that I cannot save to the X.conf file. I assume this is due to innate permissions on my user settings, which I have no idea how to properly configure. 3) I have no idea where to go from here, as most of the fixes I found online involve Linux syntax and verbiage, to which I'm totally clueless after spending over half my life with Windows.

  Read the article

• For Windows XP: How to uninstall Broadcom Bluetooth software that won't disappear

  - by T. Webster

  Hello, my situation is similar to this question for Windows 7, except my OS is Windows XP SP3. I have recently realized I made the mistake of buying a Bluetooth adapter and installing the Broadcom/Widcomm Bluetooth stack driver software. Now that I know that the software is no good, I want to install it (so I can install the Toshiba stack for the Cirago adapter). I've attempted to uninstall all Bluetooth driver software in Device Manager, and I don't see any remnants of any Bluetooth drivers there. I would include pictures here, but I don't have 10 reputation yet, so I'll just use links instead. picasaweb.google.com/lh/photo/2NAos6BP9UigPtJKaYRGyQ?feat=directlink But I do see that the little Bluetooth icon still persists: picasaweb.google.com/lh/photo/kbxgPP8ZLxhjX4ob2YjSew?feat=directlink I don't see anything about Bluetooth, Broadcom, or Widcomm in Add/Remove Programs. I don't see any folder names Broadcom or Widcomm in Program Files folder, either. But I do see that Broadcom does show up in the registry with respect to Bluetooth, as shown here. picasaweb.google.com/lh/photo/hWDo-OzB8ApibzeHA_saxQ?feat=directlink What should I do now to completely wipe this persistent Broadcom Bluetooth software off my computer?

  Read the article

• sbs-server with 2 nics and 2 connections to the internet with different providers not working as it

  - by erik-van-gorp

  We have the following configuration : A sbs-2003 server in a domain (mydomain.com) with 2 network cards, each connected to a different network (provider), with different gateways, one for web and one for mail and clients. (we do this because the bandwitdh we get from our providers is too small to handle all the mail(+spam) traffic and webservices, so we took 2 providers) DNS is as follows : www.mydomain.com 1.2.3.4 mail.mydomain.com 5.6.7.8 NIC 1(192.168.1.3) is connected to to the internet through a firewall at 192.168.1.1, having wan address 1.2.3.4 NIC 2(10.0.0.3) is connected to to the internet through a firewall at 10.0.0.1, having wan address 5.6.7.8 Both nics have their default gateway installed at their corresponding routers. Also the metrics are set equal. (i know this isn't a supported config, but it works more or less). In this configuration i can use RDP on both wan adresses, and telnet to port 25 works as well on both. The issue now is that since a few weeks , we get regular disconnections, and website hickups(timeouts), several per hour. If we set one router to a higher metric, that route no longer works. In short, I want the mails to route through NIC2 and the web through NIC1. Any better configuration (without installing a second mail server) ?

  Read the article

• How can I upgradge from Ubuntu Intrepid Ibex 8.10 to Jaunty 9.04 when old-releases no longer has the necessary packages?

  - by tommy chheng

  I changed my sources.list to: deb http://old-releases.ubuntu.com/ubuntu/ intrepid main restricted universe multiverse deb http://old-releases.ubuntu.com/ubuntu/ intrepid-updates main restricted universe multiverse deb http://old-releases.ubuntu.com/ubuntu/ intrepid-security main restricted universe multiverse I tried installing sudo apt-get install update-manager-core but i get this error: 1 upgraded, 3 newly installed, 0 to remove and 40 not upgraded. Need to get 2506kB/2555kB of archives. After this operation, 4346kB of additional disk space will be used. Do you want to continue [Y/n]? Y Err http://old-releases.ubuntu.com intrepid-updates/main update-manager-core 1:0.93.34 404 Not Found Err http://old-releases.ubuntu.com intrepid-security/main dpkg 1.14.20ubuntu6.3 404 Not Found Failed to fetch http://old-releases.ubuntu.com/ubuntu/pool/main/d/dpkg/dpkg_1.14.20ubuntu6.3_amd64.deb 404 Not Found Failed to fetch http://old-releases.ubuntu.com/ubuntu/pool/main/u/update-manager/update-manager-core_0.93.34_amd64.deb 404 Not Found E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? Running apt-get update or --fix-missing returns the same errors. How can I successfully upgrade from Intrepid Ibex to Jaunty 9.04?

  Read the article

• How can I change the binding order of network adapters in Windows 7?

  - by Chris Farmer

  The end goal here is that I am trying to install an Oracle 10g server on my Windows 7 x64 dev box. I use DHCP, and the Oracle installer is throwing up this warning: Checking Network Configuration requirements ... Check complete. The overall result of this check is: Failed <<<< Problem: The install has detected that the primary IP address of the system is DHCP-assigned. Recommendation: Oracle supports installations on systems with DHCP-assigned IP addresses; However, before you can do this, you must configure the Microsoft LoopBack Adapter to be the primary network adapter on the system. See the Installation Guide for more details on installing the software on systems configured with DHCP. I have installed the loopback adapter, but I am not sure how to make it the primary network adapter. I see this Microsoft KB article on the subject but it's Windows XP-oriented, and I can't seem to find a comparable one for Windows 7. Some of the options it talks about don't seem to be present in the views of the adapters that I see. So, how can I make the loopback adapter become the primary adapter?

  Read the article

• Recommended programming language for linux server management and web ui integration.

  - by Brendan Martens

  I am interested in making an in house web ui to ease some of the management tasks I face with administrating many servers; think Canonical's Landscape. This means doing things like, applying package updates simultaneously across servers, perhaps installing a custom .deb (I use ubuntu/debian.) Reviewing server logs, executing custom scripts, viewing status information for all my servers. I hope to be able to reuse existing command line tools instead of rewriting the exact same operations in a different language myself. I really want to develop something that allows me to continue managing on the ssh level but offers the power of a web interface for easily applying the same infrastructure wide changes. They should not be mutually exclusive. What are some recommended programming languages to use for doing this kind of development and tying it into a web ui? Why do you recommend the language(s) you do? I am not an experienced programmer, but view this as an opportunity to scratch some of my own itches as well as become a better programmer. I do not care specifically if one language is harder than another, but am more interested in picking the best tools for the job from the beginning. Feel free to recommend any existing projects except Landscape (not free,) Ebox (not entirely free, and more than I am looking for,) and webmin (I don't like it, feels clunky and does not integrate well with the "debian way" of maintaining a server, imo.) Thanks for any ideas!

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• Server 2003 and SSL Certificates

  - by Keith Stokes

  I have a Windows 2000 domain with dozens of Windows 2000 servers and a few 2003 servers. Each server runs a custom app talking to a 3rd party utilizing self-signed certificates. To help troubleshooting we've created a custom test app. The 2000 servers are able to talk within seconds. The 2003 servers take anywhere from 10-30 seconds using a domain account and much less, usually under 5 seconds using a local account. The only exception to the local account performance is a new account, which is slow initially then faster. If you leave the test app open and reconnect repeatedly it talks in seconds. If you leave it open for sometime between 1 and 2 hours, it reverts back to the previous 10 seconds, so obviously something is caching. Installing the destination certificates in the local 2003 server store makes no difference. I've installed the certificates in AD and that apparently makes domain accounts work in 9-12 seconds, vs 30 seconds that was regular before. Manually clearing the certificate store on the 2003 server makes no difference. I'm at a loss as to where the certs might be cached and if I'm using some sort of domain certificate store that's hiding from me.

  Read the article

• Mac OS X in Virtualbox says "You need to restart your computer"

  - by humoeba

  I've been trying to figure out for the past week how to get Snow Leopard reliably running in a VM. Right now I am using VirtualBox, and it runs fine for a while, but every once in a while (happened 3 times in the last few hours) I get the "You need to restart your computer" message. Unfortunately, it hasn't even lasted long enough to finish installing the operating system yet. I first tried VMWare, which was a pain to set up. I got it running ok, operating system installed, with the guest tools. Every once in a while though, it just stops running. I click inside the VM, and there's no mouse. It doesn't respond to keyboard input either. I have to reset the VM to get a response. I'm wondering if this is the same error. This happens with both Workstation and Player. Here is the tutorial I used for VirtualBox: http://www.sysprobs.com/iboot-loader-virtualbox-install-snow-leopard Here's the tutorial I used for VMWare: http://bobhood.wordpress.com/2009/12/18/welcome-to-snow-leopard-mac-os-x-10-6-and-vmware-workstation-7/ I'm using an iso for Mac OS X 10.6.3. I have an HP Pavilion dm4 with an Intel Core i7 M640 running Windows 7; VT is turned on. Using VirtualBox 4.0.4 and VMWare Workstation 7.0.1 and VMWare Player 3.0.1 Does anyone know what might be causing this error or how I can fix it? Thanks.

  Read the article

< Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >