Search Results

Search found 12019 results on 481 pages for 'stop execution'.

Page 263/481 | < Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >

• Wireless internet connection connects but internet does not work (no packets received). Wired does.

  - by Rodney

  When I connect my PC via ethernet cable to my ADSL router it works fine. When I connect via Wireless it connects and the internet will work for a random amount of time and then stop working. It stays connected with a strong signal but no packets are received. My laptop/iphone are right next to it and wireless works fine. If I open the Wireless USB status, it says it is connected to my SSID with full strength (54 mps - I am 3 meteres away from my router) and the activty shows as Packets 594 SENT and 105 RECEIVED (this goes up VERY slowly) I have tried the following: Turned off anitvirus and firewall completely. Tested the wifi signal- I am writing this on my laptop which is next to my PC and also has full wifi strength. Tried a different wireless adapter - I dug out an old PCI wireless card - it does the exact same thing. Compared all wireless settings to my laptop. I can ping google.com and it replies (sometimes with packet loss) When I reboot the PC it will connect for a minute or two (random time) and then just stops again. I tried Firefox, IE etc. no joy I have updated all latest versions (Netgear WG111v2) and drivers Checked Event Log - nothing unusual Ping the router (and even connect as admin for the few minutes when the internet does work) Changed the MTU down to 1200 using DrTCP Checked Device Manager for conflicts - none. I ping the router from the PC (192.168.0.10 - 192.168.0.1) and it replies with 4 packets. BUT, on my router admin page (which I access via http on my laptop wirelessly) - if I ping 192.168.0.10 all packets timeout (pinging my laptop 192.168.0.12 works fine) My router admin page shows the leased IP address for 192.168.0.10 (ie it is definitely talking to the router initially) Now I am out of ideas - please help. I think it is an OS/Software issue as I have tried 2 different wireless adapaters (PCI and USB) with the same result but all other wireless devices work fine around mine). It's not the firewall. It is getting assigned an IP address correctly (my PC gets 192.168.0.10, my laptop is .12) It is assigned by DHCP. As soon as I plug in the ethernet cable it all works fine. Repairing the adapter sometimes helps but it will always stop working after a random time. The wireless adapter always shows as connected with Excellent signal but the internet does not work. I am running Windows XP SP3 and have tried a Netgear WG111v2 USB adapter. Thanks in advance! UPDATE: The internet seems to be working, it is just either sending packets too small or slow to work (some small pages load bits of them very slowly but then hang). XP seems to have a networking diagnostic app - here is the output: Last diagnostic run time: 08/30/10 08:16:38 IP Configuration Diagnostic Invalid IP address info Valid IP address detected: 192.168.0.10 IP Layer Diagnostic Corrupted IP routing table info The default route is valid info The loopback route is valid info The local host route is valid info The local subnet route is valid Invalid ARP cache entries action The ARP cache has been flushed Gateway Diagnostic Gateway info The following proxy configuration is being used by IE: Automatically Detect Settings:Disabled Automatic Configuration Script: Proxy Server: Proxy Bypass list: info This computer has the following default gateway entry(ies): 192.168.0.1 info This computer has the following IP address(es): 192.168.0.10 info The default gateway is in the same subnet as this computer info The default gateway entry is a valid unicast address info The default gateway address was resolved via ARP in 1 try(ies) info The default gateway was reached via ICMP Ping in 1 try(ies) info TCP port 80 on host 65.55.12.249 was successfully reached info The Internet host www.microsoft.com was successfully reached info The default gateway is OK DNS Client Diagnostic DNS - Not a home user scenario info Using Web Proxy: no info Resolving name ok for (www.microsoft.com): yes No DNS servers DNS failure HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Passive): Successfully connected to ftp.microsoft.com. info HTTP: Successfully connected to www.microsoft.com. warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out error Could not make an HTTPS connection. info Redirecting user to support call WinSock Diagnostic WinSock status info All base service provider entries are present in the Winsock catalog. info The Winsock Service provider chains are valid. info Provider entry MSAFD Tcpip [TCP/IP] passed the loopback communication test. info Provider entry MSAFD Tcpip [UDP/IP] passed the loopback communication test. info Provider entry RSVP UDP Service Provider passed the loopback communication test. info Provider entry RSVP TCP Service Provider passed the loopback communication test. info Connectivity is valid for all Winsock service providers. Wireless Diagnostic Wireless - Service disabled Wireless - User SSID action User input required: Specify network name or SSID Wireless - First time setup info The Wireless Network name (SSID) to which the user would like to connect = RodSof Wifi. Wireless - Radio off info Valid IP address detected: 192.168.0.10 Wireless - Out of range Wireless - Hardware issue Wireless - Novice user Wireless - Ad-hoc network Wireless - Less preferred Wireless - 802.1x enabled Wireless - Configuration mismatch Wireless - Low SNR Network Adapter Diagnostic Network location detection info Using home Internet connection Network adapter identification info Network connection: Name=Local Area Connection 2, Device=Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC, MediaType=LAN, SubMediaType=LAN info Network connection: Name=Wireless USB, Device=NETGEAR WG111v2 54Mbps Wireless USB 2.0 Adapter, MediaType=LAN, SubMediaType=WIRELESS info Both Ethernet and Wireless connections available, prompting user for selection action User input required: Select network connection info Wireless connection selected Network adapter status info Network connection status: Connected HTTP, HTTPS, FTP Diagnostic HTTP, HTTPS, FTP connectivity info FTP (Active): Successfully connected to ftp.microsoft.com. warn HTTP: Error 12007 connecting to www.microsoft.com: The server name or address could not be resolved warn HTTP: Error 12002 connecting to www.hotmail.com: The operation timed out warn HTTPS: Error 12002 connecting to www.passport.net: The operation timed out warn HTTPS: Error 12002 connecting to www.microsoft.com: The operation timed out error Could not make an HTTP connection. error Could not make an HTTPS connection.

  Read the article

• Very large log files in IIS 7.x

  - by Neal

  Hello, I had a site stop working today and when I RDP'd into the server I saw a warning about low disk space. The first thing I checked was the inetpub folder where the log files are stored and sure enough it was huge, 40 GB huge. I do clean the files monthly but what is causing a day's worth of logging on a medium activity site (www.vbdotnetforums.com) to create 300-500 MB log files? I do have everything being logged so my SmarterStats software gives me the most info, but are there specific things I should/can turn off that is causing the most growth in these log files? Also, sure would be nice if Microsoft someday had some sort of log file management such as deleting log files after they exceed a certain size (total), X days, etc. We all have to come up with some solution to delete the old ones manually. Thanks Neal

  Read the article

• Computer wont POST after power outage

  - by aaron

  I had just turned my computer on and windows was loading when the power in my neighborhood went out. Normally, when I turn my computer on, the video card fan spins up, then slows down, POST and windows boots. Now, after the blackout, the video card fan spins fast and wont stop. Nothing is displayed on the monitor. The monitor does not detect that the video card is sending it signals, it just stays on standby. No POST or beep codes. This is what I have tried so far: My motherboard has 2 PCI express slots and I tried plugging the video card into both of them but that didn't fix anything. I have replaced the power supply, that didn't fix anything. I cleared the CMOS, that didn't fix anything. Does anyone have any idea of what could be wrong? Thanks!

  Read the article

• Cabling: What to keep in stock?

  - by pehrs

  I have worked a few different places, each one with a different solution, so I would like to hear your suggestions and ideas. I am looking at a situation with multiple server-rooms. We have a mixture of copper (both ethernet and telephone), multi-mode fibre and single-mode fibre. We have all types of connectors: RJ-11, RJ-45, LC, SC, FC, SMA and several I probably forgot about. We have a lot of people working in the area, and keeping track of cables is turning into a full time job. So, here are a the questions: What types and lengths of cable do you keep in stock on site? Do you make your own or buy pre-made? Adapters? Dampeners? How do you manage cable inventory? How do you label the cables? Any other tricks to stop this from driving me crazy?

  Read the article

• How can I terminate wisptis.exe in Windows XP SP2

  - by user9950

  I am working in a production environment. Basically I work on graphics oriented enviroment so I used to work on catia and windchill as well. When I am opening a part or diagram in Catia along with CNEXT .exe (catia service) wisptis.exe is starting and making the system halt and Catia will crash. So I need to restart the worksation or I need to close all applications then I need to open catia then again the same problem. So please tell me how to avoid this or stop the wisptis.exe service. If I want to work on catia I need to kill wisptis.exe service otherwise I cant work.

  Read the article

• Httpd restart "Address already in use" error

  - by mtndesign

  I have an .rpm, which I created. In its %post part, I do some stuff, and in the end of this script, i call service httpd restart. It gives the following error: + service httpd restart Stopping httpd: [FAILED] Starting httpd: (98)Address already in use: make_sock: could not bind to address [::]:81 (98)Address already in use: make_sock: could not bind to address 0.0.0.0:81 no listening sockets available, shutting down Unable to open logs [FAILED] I got this from the rpm verbose installing (-vv). So I know its about httpd restart itself, nothing else. The according to netstat only one process (httpd) is listening on port 81. $ sudo netstat -nlp | grep 81 tcp 0 0 :::81 :::* LISTEN 29670/httpd I don't understand, why running http FAILS at stop, and FAILS again in start. Any ideas how to solve this?

  Read the article

• Bacula not backing up all the files it should be doing

  - by Nigel Ellis

  I have Bacula (5.2) running on a Fedora 14 system backing up several different computers including Windows 7, Windows 2003 and Windows 2008. When backing up the Windows 2008 server the backup stops after a relatively small amount has been backed up and says the backup was okay. The fileset I am trying to backup should be around 323Gb, but it manages a mere 27Gb before stopping - but not erring. I did try creating a mount on the Fedora computer to the server I am trying to backup, and Bacula managed to copy 58Gb. When I tried to use the mount to copy the files manually I was able to copy them all - there are no problems with permissions etc. on the mount. Please can anyone give a reason why Bacula would just stop? I have heard there is a 260 character limit, but some of the files that should have been copy resolve to a shorter filename than some that have been backed up.

  Read the article

• Screen gets stuck in a dim setting after waking up

  - by Mason Wheeler

  I've got a laptop that I recently upgraded from Vista to Windows 7. It works a lot better now for a lot of things, but there's one problem I've had happen a few times that never happened under Vista. When I put the system to sleep, then occasionally when I wake it up again, for no apparent reason, the screen's dim. Sometimes it's as if half the backlighting was turned off, and sometimes it's as if all the backlighting was turned off, all except for the mouse pointer, which remains as bright white as ever. Trying to change the screen's brightness does nothing, but rebooting fixes this. Has anyone else seen this? Any ideas on what's causing it or how to make it stop happening?

  Read the article

• Windows Fax Server Leaves Documents in "Pending" Status

  - by Chris

  We are having an issue with Windows Fax Server on Windows Server 2008. Occasionally, the server will get into a state where after adding jobs to the outbox, they will simply remain at the pending status (without any attempt to send them). There is nothing in the event log mentioning a problem. It typically seems to enter the state after restarting the server or after no faxes have been sent for a while. The way to fix the issue has been to: Stop the Fax service Go into the modem properties in device manager and query modem Start the Fax service - at which point all the pending faxes in the outbox will send.

  Read the article

• Firewall blocks FTP PASV response

  - by harper

  0 down vote favorite I have an FTP server that supports passive server mode (using PASV command). This works fine with Windows XP. When I want to access this server from Windows Vista or Windows 7 with firewall enabled I experience a immediate connection shutdown. A reset packet is sent to the server, the socket is signaled that the server had reset the connection (what is not true). The problem disappears when the firewall is disabled. Connections to other FTP servers work correctly. The difference is that the servers response to PASV does not enclose the address field with parentheses. This is legal as documented in RFC-959 and RFC-1132. How can I configure the firewall to stop this bad behavior?

  Read the article

• CentOS 6.5 as WebServer for Django Dev

  - by Charlesliam

  During CentOS 6.5 Installation I choose WebServer type for this computer. The server has a static IP address 192.168.111.100. The CentOS was updated I managed to install virtualenv with Python 2.7. Within the virtualenv, I'll be using Django Framework. After I tried to run the command using root user python manage.py runserver 0.0.0.0:8000 I can't see the website from other computer within the LAN when I try to type 192.168.111.100:8000/admin on my browser. I already disable firewall using service iptables stop I can ping the 192.168.111.100 and I have a good feedback with nslookup. What seems the problem of my config?

  Read the article

• Running rebaseall on Cygwin

  - by Erik Vold

  I tried building node.js on cygwin and that caused errors, so someone in #node.js on freenode told me to run rebaseall on cygwin to clean it up. So I tried that and I got the following message: $ rebaseall rebaseall: only ash or dash processes are allowed during rebasing Exit all Cygwin processes and stop all Cygwin services. Execute ash (or dash) from Start/Run... or a cmd or command window. Execute '/bin/rebaseall' from ash (or dash). So I closed cygwin, went to Start/Run and tried ash and dash but got the following alert: Windows cannot find 'ash'. Make sure you typed the name correctly, and then try again. To search for a file, click the Start button, and then click Search. So what am I supposed to do??

  Read the article

• New apache on mac

  - by Keith

  I have installed php5 apache2 mysql5 and postgresql84 using MacPorts. I realize my mac already has apache but it didn't have apache2 nor postgesql hooked up to use with php. I want to not use the default apple apache and use the new macports install. How do I tell my computer to stop looking at the old apache? When I do apachectl in the terminal I believe it is using the old apache. I would like to hook it up to use the new one. How would I do that? The new stuff is installed at /opt/local/apache2 and the old stuff is installed at /private/etc/apache2 I went to system preferences...Sharing...and shut off Web Sharing but when I do apachectl's that turns it on and off in the preferences. I'm running in Snow Leopard.

  Read the article

• Reduce Windows DNS Service caching on Window

  - by Nick G

  I'm struggling with DNS caching issues on a Windows based LAN. I've noticed that if I change a DNS record on a domain hosted by a 3rd party nameserver, that I always seem to be the very last person to see the change happen. I can often query the domain using a service which checks propagation around the world like www.whatsmydns.net but I usually find that all other DNS servers are correct and it's only my own server which has the old IP - even 8-12 hours later. This is an issue for us as we're website developers and often making changes to DNS records so these huge delays are frustrating. It seems to be because our primary domain controller server (+Active Directory & DNS) on our LAN (which is also our local DNS server) caches records for AGES (Way beyond it's published TTL). How can I stop the Windows DNS server from caching, or reduce the caching to only an hour or so?

  Read the article

• Max ping response time?

  - by DougN

  I'm wondering what a maximum (practical) ping response time might be. As far as I know, there isn't a max defined anywhere (TTL, but that's hops, not time). As I think about it, I'm not sure I've ever seen a ping response time of more than a second or so. But as far as I know, there is nothing to stop a remote host from waiting (or being really busy) and not sending the response back for a few seconds. As a simple data point, I just pinged a number of servers around the world and the worst time I could find was 350ms.

  Read the article

• Graphics Startup Screen

  - by Wesley

  Specs: AMD Athlon XP 2400+ @ 1987 MHz / 2x 512MB PC3200 DDR RAM / 160GB IDE HDD / 128MB GeForce 6200 AGP / FIC AM37 / Windows XP Pro SP3 So, every time I start up my machine, there's a startup screen for the graphics card. It should display "NVIDIA GeForce 6200 VGA BIOS" with some other copyright information underneath it. However, it randomly changed to say "NV44A VGA BIOS." I think the GeForce 6200 codename is NV44A or something, but is there someway to change it back to say "GeForce 6200 VGA BIOS" or, if not, to completely stop it from showing upon startup? (Graphics drivers are all up to date.) Thanks in advance.

  Read the article

• How to keep Windows 7 from sleeping while scanning the PC.

  - by D Connors

  So, I've been using Microsoft Security Essentials lately. And it usually takes a couple hours or more for it to full scan my hard drive. Because of that, I commonly leave it scanning while I go do something else. Problem is: 10 minutes later, windows 7 goes to sleep, and the scan is (obviously) paused. That's What I'd like to stop happening. So far, the only way I've been able to avoid it was to create a power plan, and switch to it while away, to keep the PC from sleeping. Problem is that I have to keep switching power plans and I'd like the PC to be able to go to sleep in case MSE finishes scanning and I'm still not back. Maybe I'm just asking for too much, but I've been surprised by the users here plenty of times already. So let me know if you know how to keep the PC from sleeping while MSE is scanning. Thanks

  Read the article

• How to fix monitor detection on Windows 7?

  - by Boaz

  Hi, I'm using Windows 7 + Windows Media Center for my HTPC. It works great except from one annoying issue. Whenever I turn off my TV while listening the music, the music stop for a second or while Windows 7 tries to figure out what monitor is attached. After that second it settles down on a default 800x640. While not a big deal, it is annoying as I don't want to have the TV on while playing music. Is there anyway to fix the monitor/disable monitor auto-detection on Windows 7 so it would not start recalibrating everything when I turn off my TV? Thanks, Boaz

  Read the article

• How to allow program updates without prompting UAC?

  - by Ryan Mortier

  We have about 15-20 users who have this software installed. We have UAC enabled through GPO as you should, which means the software prompts for admin approval if a standard user trys to install it. Thats fine, they can call the help desk to have the software installed. My problem is, our help desk is being bombarded every day because users can't update the software and there are updates almost every day which is prompting UAC. Using procmon.exe to find out where it was trying to write to, I then created a GPO to allow file permission access to the program files folder for this particular software, including the program data folder, but it still prompts for admin approval. It seems as though that the software is using msiexec.exe to run a .msp patch file. The only "ACCESS DENIED"s I can still see in procmon is things like this: What can I possibly do to stop this software from prompting UAC with admin password credentials aside from disabling UAC?

  Read the article

• PERC 5/i Enable alarm on disks failures

  - by Andy M

  I'm trying to enable one the alarm of my server's raid controller PERC 5/i. Using this documentation, under the chapter Audible Alarm Warnings, it's explained that enabling an audible alarm is allowed in order to quickly spot failures on my hard disks. My trouble is that when entering the disk controller configuration (Ctrl+R at boot time), I'm able to set up lot of things but I cannot navigate to Enable Audible Alarm. I have : Enable Controller BIOS Enable Alarm Enable BIOS stop on Error I can navigate with my arrow keys to both the first and third items, but I cannot navigate to or select the second! It's not greyed out, and seems like I should be able to select go on this entry, but my cursor keep skipping it. Any ideas about what I'm missing here?

  Read the article

• Explorer.exe keeps crashing if effects are enabled

  - by Allende

  The explorer.exe keeps crashing before every minute after starts when all the effects are activated. These are the details of the error: Problem signature: Problem Event Name: InPageError Error Status Code: c0000185 Faulting Media Type: 00000003 OS Version: 6.1.7600.2.0.0.256.48 Locale ID: 1033 Additional Information 1: a7aa Additional Information 2: a7aa91f17ea749d42a4de3b390fa5b3d Additional Information 3: a7aa Additional Information 4: a7aa91f17ea749d42a4de3b390fa5b3d Read our privacy statement online: http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409 If the online privacy statement is not available, please read our privacy statement offline: C:\Windows\system32\en-US\erofflps.txt I suspect there's a problem with my hard drive ('cause I already have to format/install twice before this error) but not pretty sure why if I disable all the effect (Performance options) help to stop the issue. Anyway if someone have any idea, thanks. I already replace shell32.dll and explorer.exe using the windows 7 dvd Laptop Model: ProBook 4520s Windows Version: Profesional 32 bits. My regards

  Read the article

• In windows 7, how do I disable "Ease of Access" pop ups on the logon screen as I am typing my passwo

  - by Silfheed

  Heyas So the question is pretty much in the title. Things to note: 'Use On-Screen Keyboard' is un-checked I have disabled Ease of Access by replacing utilman.exe But my problem now is that when I'm typing my password, It'll stop all together on the 'u' or the 'p' character and I have to click on the ease of access button then move focus back to the password to continue. Yes, one obvious solution is to not use a password that has 'u' or 'p' in it (which I've done), but that's obviously not a completely satisfying answer. Thanks! I feel a tumbleweed badge...

  Read the article

• Weird noise while scanning, using scanimage and a Canon Lide 35

  - by Manu

  I'm trying to scan a bunch of images, using xsane's scanimage : scanimage --format=tiff --batch --batch-prompt This command scans the first picture perfectly, but as soon as I press enter, the scanner makes a weird noise, and the scanning "arm" moves very, very slowly. If I stop scanimage and start again, it scans normally again. Is there another scanimage option that I need to add? I've checked the man page, but can't see what I'm missing. Edit: the problem seems to be that the scanning "arm" doesn't go back to it's original position after the first scan.

  Read the article

• In Ubuntu, MoBlock makes it take a while to actually start using internet

  - by Matchu

  When connecting to wireless internet in Ubuntu (tested with two different networks), I connect nearly instantly. However, to actually load a page, I need to wait a few minutes, at which point I can actually use a web browser or Pidgin. Until then, various applications try to connect until they time out. I've discovered that, if instead of waiting a few minutes, I open Terminal and run sudo /etc/init.d/blockcontrol stop, everything suddenly is able to load. I can then start MoBlock again with no ill effects. Why is this happening? What is it that would cause MoBlock to take a few minutes to start letting traffic in, but only when started on bootup? Thanks!

  Read the article

• Could it be sane to use Windows Server 2012 as desktop

  - by nCdy

  what about using it on desktop? I've got enough strong PC with intel core i7 and 8GB Ram so what should I think about: why not? Were looking about major differences compared to windows 8, found less. for example new file system - can it affect me? In my usual day I need development instruments alike visual studio, virtualization tools, and some games So far I can't find something that must stop me, everything I need can work (seems like) there. Tell me why I must not do it or if that is sane to do.

  Read the article

< Previous Page | 259 260 261 262 263 264 265 266 267 268 269 270  | Next Page >