Search Results

Search found 8897 results on 356 pages for 'hit detect'.

Page 273/356 | < Previous Page | 269 270 271 272 273 274 275 276 277 278 279 280  | Next Page >

• Linux will not activate wireless after device has been re-enabled

  - by XHR

  Using a Eee 900A netbook by Asus. By pressing Fn + F2, I can disable or enable the wireless chip on the netbook, a blue LED indicates the status. I've been able to connect to wireless networks just fine with this netbook. However, if the wireless chip ever becomes disabled, I have to reboot to get my network connection back. This generally happens when suspending. For some reason the LED will be off and I have to hit Fn + F2 for it to light up again. However, after doing so, Linux will not reconnect to the network. It simply changes the wireless status from "wireless is disabled" to "device not ready". Even worse, I've recently had issues with the chip being enabled at boot, thus making it nearly impossible to get connected. I've searched around on-line but haven't found much of anything useful on this. This happens on all kinds of different distros including Ubuntu 9.10 Netbook, EeeBuntu 4 beta, Jolicloud and Ubuntu 10.04 Netbook. Edit I noticed this question is getting a lot of views. To give a quick update, I never did resolve this issue with the given distro's. However, I'm currently running Ubuntu 10.10 netbook edition and this issue has gone away.

  Read the article

• Netgear CG3000D new Modem/Router - Random High Ping

  - by justin.chmura

  Cox just recently came out and looked at my internet and decided that the modem I had was causing high latency issue. The speed was fine but the ping would spike to around 100 and over when gaming or putting a load more than browsing on the line. After they replaced it, it seems like I get better latency, but when it spikes, I get upwards of over 300 ping with like 500 jitter. I figured I would hit the serverfault universe before sending another email to Cox. I opted not to do the Cox setup as it was an extra $20 which I thought would have just setup the wireless (which I can handle). Is it a setting or something that I missed that needs to be setup? The firmware for the CG3000D is awful and not fun to use. I did change some hidden settings on the RgServices.asp page (I'll attach a screenshot). I've also heard that the Router/Modem combos are awful and that I should go back and just ask for a modem stand-alone. Any input is helpful. All screenshots: http://imgur.com/a/JX6qu#0

  Read the article

• Httpd and LDAP Authentication not working for sub-pages

  - by DavisTasar

  I just recently installed a Nagios implementation, and I'm trying to get LDAP authentication working for httpd on Red Hat. (nagios.conf for Apache config below, sanitized of course) ScriptAlias /nagios/cgi-bin "/usr/local/nagios/sbin" <Directory "/usr/local/nagios/sbin"> #SSLRequireSSL Options ExecCGI AllowOverride none AuthType Basic AuthName "LDAP Authentication" AuthLDAPURL "ldap://my.domain.controller:389/OU=Users,DC=my,DC=domain,DC=controller?sAMAccountName?sub?(objectClass=user)" NONE AuthzLDAPAuthoritative off AuthLDAPBindDN "CN=NagiosAdmin,DC=my,DC=domain,DC=controller" AuthLDAPBindPassword "myPassword" require valid-user </Directory> Alias /nagios "/usr/local/nagios/share" <Directory /usr/local/nagios/share> #SSLRequireSSL Options None AllowOverride none AuthBasicProvider ldap AuthType Basic AuthName "LDAP Authentication" AuthzLDAPAuthoritative off AuthLDAPURL "ldap://my.domain.controller:389/OU=Users,DC=my,DC=domain,DC=controller?sAMAccountName?sub?(objectClass=user)" NONE AuthLDAPBindDN "CN=NagiosAdmin,DC=my,DC=domain,DC=controller" AuthLDAPBindPassword "myPassword" require valid-user </Directory> Now, the initial authentication works, so when you first hit the page you can log in just fine. However, when you go anywhere else, it prompts you for authentication, fails (asking for a re-prompt), and gives this error message: [Mon Oct 21 14:46:23 2013] [error] [client 172.28.9.30] access to /nagios/cgi-bin/statusmap.cgi failed, reason: verification of user id '<myuseraccount>' not configured, referer: http://<nagiosserver>/nagios/side.php I'm almost certain its a simple flag or option, but I just can't find it, and I don't have a lot of experience working with Apache. Any assistance or help would be greatly appreciated.

  Read the article

• Is there a utility to visualise / isolate and watch application calls

  - by MyStream

  Note: I'm not sure what to search for so guidance on that may be just as valuable as an answer. I'm looking for a way to visually compare activity of two applications (in this case a webserver with php communicating with the system or mysql or network devices, etc) such that I can compare the performance at a glance. I know there are tools to generate data dumps from benchmarks for apache and some available for php for tracing that you can dump and analyse but what I'm looking for is something that can report performance metrics visually from data on calls (what called what, how long did it take, how much memory did it consume, how can that be represented visually in a call stack) and present it graphically as if it were a topology or layered visual with different elements of system calls occupying different layers. A typical visual may consist of (e.g. using swim diagrams as just one analogy): Network (details here relevant to network diagnostics) | ^ back out v | Linux (details here related to firewall/routing diagnostics) ^ back to network | | V ^ back to system Apache (details here related to web request) | | ^ response to V | apache PHP (etc) PHP---------->other accesses to php files/resources----- | ^ v | MySQL (total time) MySQL | ^ V | Each call listed + time + tables hit/record returned My aim would be to be able to 'inspect' a request/range of requests over a period of time to see what constituted the activity at that point in time and trace it from beginning to end as a diagnostic tool. Is there any such work in this direction? I realise it would be intensive on the server, but the intention is to benchmark and analyse processes against each other for both educational and professional reasons and a visual aid is a great eye-opener compared to raw statistics or dozens of discrete activity vs time graphs. It's hard to show the full cycle. Any pointers welcome. Thanks! FROM COMMENTS: > XHProf in conjunction with other programs such as Perconna toolkit > (percona.com/doc/percona-toolkit/2.0/pt-pmp.html) for mySQL run apache > with httpd -X & (Single threaded debug mode and background) then > attach with strace -> kcache grind

  Read the article

• Can not open ports in iptables on CentOS 5??

  - by abszero

  I am trying to open up ports in CentOS's firewall and am having a terrible go at it. I have followed the "HowTo" here: http://wiki.centos.org/HowTos/Network/IPTables as well as a few other places on the Net but I still can't get the bloody thing to work. Basically I wanted to get two things working: VNC and Apache over the internal network. The problem is that the firewall is blocking all attempts to connect to these services. Now if I issue service iptables stop and then try to access the server via VNC or hit the webserver everything works as expected. However the moment I turn iptables back on all of my access is blocked. Below is a truncated version of my iptables file as it appears in vi -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5801 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5901 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 6001 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 5900 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT Really I would just be happy if I could get port 80 opened up for Apache since I can do most stuff via putty but if I could figure out VNC as well that would be cool. As far as VNC goes there is just a single/user desktop that I am trying to connect to via: [ipaddress]:1 Any help would be greatly appreciated!

  Read the article

• AutoHotKey temporarily rebind Winkey

  - by wes

  I've got a wireless keyboard that puts some media keys on top of the Function keys, so that by default F4 is actually lock (Rwin & l) and Fn+F4 is a real F4. So I'd like to basically switch those around. Here's what the key history shows: VK SC Type Up/Dn Elapsed Key ------------------------------------- 73 03E d 17.32 F4 ; Fn+F4 73 03E u 0.16 F4 5C 15C d 2.96 Right Windows ; F4 4C 026 d 0.00 L 5C 15C u 0.13 Right Windows 4C 026 u 0.00 L This doesn't do anything: SC15C & SC026::MsgBox,Pressed F4 But this prints that I hit F4 then goes to the login screen: Rwin & l::MsgBox,Pressed F4 So how can I stop it from switching to the login screen? Ideally I'd like F4 (which registers as Rwin & l) to just send F4, Fn+F4 to send Rwin & l, and also have them work with other keys (e.g., a manual !F4 should still close a window). Is this possible?

  Read the article

• Server-side SSH jump hosts

  - by Dan Sosedoff

  Trying to figure out server side SSH jump hosts logic. Current network schema: [Client] <--> [Server A: hostname: a.com] <--> [Server B] [Client] <--> [Server A: hostname: b.com] <--> [Server C] Server A responds to both DNS records. Possible flow: Client opens a ssh connection with ssh [email protected]. Server A accepts it and should automatically jump user onto Server B with ssh user2@server_b.com. Client opens a ssh connection with ssh [email protected]. Server A accepts it and should automatically just user onto Server C with ssh user2@server_c.com. In other words, client should be able to connect to the target without performing any local configuration, assuming that we have a stock ssh config. The problem with ssh jumps is that user has to define hosts in local ~/.ssh/config file, which is not acceptable in my case. It needs to be a default sshd behavior. Im aware that you can define a custom command ~/.ssh/authorized_keys on server, but i dont think there is a way to properly detect source hostname where user tries to connect. It is possible at all ?

  Read the article

• Host system resets (crashes) when using VMWare or VirtualBox and 64-bit guest systems

  - by sinni800

  I have been trying to install virtual systems on VMWare for a while now and encountered strange behaviour from my PC. The behaviour is as follows: On "automatic" virtualization mode it either outputs a cryptic error message (can MAYBE give later, if I can reproduce) right on startup (before even the BIOS) or it resets the complete HOST system (blackscreen, bios...) If I install a Windows XP on it it works well on "binary translation" mode. If I try installing Linux on it, in "binary translation" mode it crashes 1 or 2 seconds after I hit enter on the GRUB selection screen (after the first page of kernel messages rolled in) Using VirtualBox it crashes right in the BIOS. It gave me a Bluescreen though! 0x00000101: CLOCK_WATCHDOG_TIMEOUT: a clock interrupt was not received on a secondary processor within the allocated time interval NEWS: I tried VirtualBox again and it did not completely crash the computer this time. It gave me a critical error and a log file: http://pastebin.com/yKZSDs91 In conclusion, it will crash instantly if VT-x is activated. If not, it seemingly only crashed if I try to install something with 64 bits. Another update: Yes, it ONLY crashes when the guest is 64 bit! What I tried: Reinstalling Windows (my Windows installation was quite broken so it seemed natural. Didn't work though.) New BIOS What I am certain of: Virtualization extensions are activated in the BIOS What my computer specs are: ASUS P8P67 LE mainboard, newest BIOS/EFI firmware Intel Core i5 2500k Ati Radeon HD 5770 16 GB Corsair 1333mhz DDR3 RAM, 4 X 4 GB

  Read the article

• How do you recreate the System Recovery environment in Windows 7?

  - by Howiecamp

  I'm running Windows 7 Home Premium RTM (64-bit) and I want to take advantage of the system recovery tools (eg the Command Prompt) without using the Windows 7 DVD. My understanding is that this environment (WinRE) should be installed to your HDD by default as part of the Windows 7 installation. However, when I hit F8 on boot and select "Repair", I get: Windows failed to start. A recent hardware or software change might be the cause. To fix the problem... Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible. The "Info" line seems like the smoking gun. My next step was to boot from the Windows 7 DVD, and choose "Repair". It indicated my Recovery Environment wasn't on the Windows 7 boot menu (perfect) and offered to fix it. I said yes and rebooted, however same issue as above. In addition, when I booted in to Windows 7 and I looked at the boot menu options, the recovery/repair option was not there. Only my Windows installation. Finally, I ran the Disk Management tool (diskmgmt.msc) and took a look at the contents of my "System Reserved" partition (which was set to "Active" as normal). It's unclear to me what the contents should look like, however it is my understanding that the WinRE environment gets installed to this partition. (As part of the above troubleshooting I followed http://superuser.com/questions/25728/how-to-fix-windows-7-boot-process which lead to http://www.sevenforums.com/tutorials/668-system-recovery-options.html).

  Read the article

• IP to IP forwarding with iptables [centos]

  - by FunkyChicken

  I have 2 servers. Server 1 with ip 1.1.1.1 and server 2 with ip 2.2.2.2 My domain example.com points to 1.1.1.1 at the moment, but very soon I'm going to switch to ip 2.2.2.2. I have already setup a low TTL for domain example.com, but some people will still hit the old ip a after I change the ip address of the domain. Now both machines run centos 5.8 with iptables and nginx as a webserver. I want to forward all traffic that still hits server 1.1.1.1 to 2.2.2.2 so there won't be any downtime. Now I found this tutorial: http://www.debuntu.org/how-to-redirecting-network-traffic-a-new-ip-using-iptables but I cannot seem to get it working. I have enabled ip forwarding: echo "1" > /proc/sys/net/ipv4/ip_forward After that I ran these 2 commands: /sbin/iptables -t nat -A PREROUTING -s 1.1.1.1 -p tcp --dport 80 -j DNAT --to-destination 2.2.2.2:80 /sbin/iptables -t nat -A POSTROUTING -j MASQUERADE But when I load http://1.1.1.1 in my browser, I still get the pages hosted on 1.1.1.1 and not the content from 2.2.2.2. What am I doing wrong?

  Read the article

• Microsoft Mouse and Keyboard Center - Slow response for App-specific shortcuts

  - by Darrel Hoffman

  So a few months ago, I bought a new MS mouse, and was surprised that they'd discontinued Intellipoint in favor of this Microsoft Mouse and Keyboard Center. It seems to have the same functionality underneath all the bloat, but there's a very serious drawback - when I set up application-specific functions for the extra buttons on the mouse, they work, but sometimes with a very long delay, like up to a minute or more. For example, I often set up the left side button as an "Undo" in various programs for convenience. But sometimes, when I try to use that Undo button, nothing happens, so I'm forced to use the standard Ctrl-Z or whatever. But then, a minute or so later, it suddenly remembers that I hit that button a while back, and calls the Undo unexpectedly on something entirely different. It's infuriating. No modern computer function should be this slow. It's not the software or the computer itself, because doing an Undo via Ctrl-Z or the menu still works instantly. It's very definitely a side-effect of delayed response to the mouse button. Usually after it delays the first time, it'll work quickly after that, but if you haven't used a given shortcut in several minutes, it "forgets" again and you get another inexplicably long delay. Intellipoint never had this problem, but it's not supported any more, and not compatible with the newer mice. Has anyone else noticed slow-downs with MS M&K C and app-specific shortcuts? Any ideas how to get around this? I use these shortcuts extensively in my workflow and it's just entirely unacceptable to have such a long delay in what should be a pretty basic feature.

  Read the article

• On clients use generic driver for printer shared by CUPS

  - by Daniel

  I know this worked really easy with a recent CUPS version some years ago. Unfortunately I fail to do the following with latest CUPS nowadays. How to share a printer without using printer specific drivers on the clients with CUPS? The printer is a Samsung ML-2010. The important fact is that it needs a quite specific library for printing called splix. That is installed on the server and prints well. What makes trouble is using that printer over the network. I found out how to use Avahi under Linux to make use of DNSSD to advertise and discover printers. But as far as I understand the new CUPS offers the internal driver interface on the network. This has 2 major issues: anybody can fiddle with the driver and I don't trust any uncommon printer library to be "network secure" anyone who wants to use my printer including guests needs to install the specific drivers first I remember the old days when I could enable "Share this printer" on the CUPS server and all clients would magically detect the printer and just send their job data to the server and have it do the driver stuff. After everything a read I guess this is related to the changes Apple introduced with CUPS including dropping of the integrated network discovery protocol. If it helps: Server: Ubuntu LTS 12.04 Server with CUPS 1.5.3 Client: Arch Linux with current CUPS 1.6.1 On another box with Ubuntu the printer was setup automatically at least but the mechanism used the Splix library for that.

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup.

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• Changing the prompt in telnet

  - by wim

  With some help from people on here, I was able to set a custom prompt in an ssh session (thanks!). Now I need to do the same in telnet, but I'm not sure of what syntax I could use for that. Basically the telnet prompt is just a > character, I need to modify it to something I can more reliably detect in automation jobs. Hope this makes sense. From inside telnet, trying to escape that command with a bang like !PS1=spam and !PS2=eggs did not change it. wim@wim-acer:~$ ssh [email protected] -i ~/.ssh/guest_nopassphrase -t "export PS1='Sending a custom prompt \w \$ '; exec sh" Sending a custom prompt ~ $ set HOME='/var/tmp' IFS=' ' LOGNAME='guest' PATH='/sbin:/usr/sbin:/bin:/usr/bin' PPID='1128' PS1='Sending a custom prompt \w $ ' PS2='> ' PS4='+ ' PWD='' SHELL='/bin/sh' TERM='xterm' USER='guest' Sending a custom prompt ~ $ telnet localhost <snip> Entering character mode Escape character is '^]'. > !set CONSOLE='/dev/ttyp0' HOME='/var/tmp' IFS=' ' LOGNAME='root' PATH='/sbin:/bin:/usr/sbin:/usr/bin' PPID='546' PREVLEVEL='N' PS1='\w \$ ' PS2='> ' PS4='+ ' PWD='/var/tmp' RESPAWN_COUNT='1' RESPAWN_LAST='0' RESPAWN_MAX='5' RESPAWN_TIME='5' ROOTDEV='/dev/sla1' RUNLEVEL='5' SHELL='/bin/false' TERM='linux' USER='root' > > Connection closed by foreign host Sending a custom prompt ~ $ Connection to 192.168.1.124 closed. wim@wim-acer:~$

  Read the article

• How to verify system using right GPU, after system reset [duplicate]

  - by Antoros

  This question already has an answer here: Is my mobile AMD card being used? 2 answers OS: Windows 8 CPU: Intel® Core™ i7 Processor 3635QM GPU 1 : Intel HD Graphics 4000 GPU 2 : AMD Radeon™ HD 8870M other info: System Spects Problem: im unsure that CCC is using AMD card instead of Intel's, i have encountered several issues since updating to 8.1 and i don't know what to do What happened: Installed 8.1 patch first day After 1 minute of use, BBSOD, windows never loaded again System restore wouldnt recognize 8.0 restore points i did a system reset to windows 8 since the laptop was only 3 weeks old System Broke, it did restore to factory BUT kept the registry almost intact, i had to install almost everything again, since the factory drivers where working with the updated one's registry and several problems CCC Broke too <- What i've already done Installing new drivers on top of old ones didnt work, so i used AMD uninstaller first Uninstalled and Re-installed Intel's HD Graphics Driver Tried to install mobile center, but AMD told me that it wasnt compatible (even if thats the only driver that they provide via their page as seen Here) Tried to use Auto-Detect, couldnt install driver because card was disabled because it didnt have the drivers... (see what they did here?) Had to use a workaround with Samsung Update, the driver didnt appear as download so had to use search and downloaded the driver manually. Now the graphic card appears on device manager and catalyst but as 8800 series (not exact model), and cant check the card with neither dxdiag/GPU-z/HWMonitor when right-clicking on CCC only Intel card appears launching a game and using as "high performance" would speed it up a little but i cant be sure How to verify its working properly? HWMonitor wont show AMD card even when set to high performance Latest GPU-Z wont work because a problem with Intel's, and legacy ones wont either what can I do now? I don't even know if I fixed my problem or not, and i also want to to use Adobe Premier with it, and its locked (the option to run it with the amd card not intels) Edit: now it seems to work, but cant change the setting for adobe Premiere and other programs that i Need to

  Read the article

• HAProxy crashes on all requests in 1.5-dev12

  - by Daniel Hough

  I'm having an issue where HAProxy is crashing with no explanation when I switch from 1.4.12 to 1.5-dev12. The reason I'm switching is for the SSL offloading. My config file doesn't have any errors, it's quite simple and it works well with 1.4 - but for some reason when I run it with 1.5-dev12 I see the logs noting that the two backends I have have been set up, and then when I hit one of the frontends, I get an HTTP 400 in the browser and suddenly HAProxy isn't running anymore when I check. I understand that a common workaround to the lack of SSL support for HAProxy is to use Stud, and I may go with that since I am in need of an SSL solution for my service, but before I dele into that world I thought I might see if anybody has experienced the same problems and might know how to fix it. The server is Ubuntu 10.04 and I followed the make instructions on the Exceliance blog here. EDIT: On the advice of Kyle Brandt, I did a bit more investigation. I attached gdb to the haproxy process and when the crash occurred this is what I got: Program received signal SIGSEGV, Segmentation fault. 0x0804e5c2 in dequeue_all_listeners (list=0x9e1a418) at src/protocols.c:184 184 list_for_each_entry_safe(listener, l_back, list, wait_queue) { P.S. HAProxy is awesome, so thank you Exceliance for providing us with something so useful :)

  Read the article

• How to tell nginx to honor backend's cache?

  - by ChocoDeveloper

  I'm using php-fpm with nginx as http server (I don't know much about reverse proxies, I just installed it and didn't touch anything), without Apache nor Varnish. I need nginx to understand and honor the http headers I send. I tried with this config (taken from the docs) but didn't work: /etc/nginx/nginx.conf: fastcgi_cache_path /var/lib/nginx/cache levels=1:2 keys_zone=website:10m inactive=10m; fastcgi_cache_key "$scheme$request_method$host$request_uri"; /etc/nginx/sites-available/website: server { fastcgi_cache website; #fastcgi_cache_valid 200 302 1h; #fastcgi_cache_valid 301 1d; #fastcgi_cache_valid any 1m; #fastcgi_cache_min_uses 1; #fastcgi_cache_use_stale error timeout invalid_header http_503; add_header X-Cache $upstream_cache_status; } I always get "MISS" and the cache dir is empty. If I uncomment the other directives, I get hit, but I don't want those "dumb" settings, I need to control them within my backend. For example, if my backend says "public, s-maxage=10", the cache should be considered stale after 10 secs. Instead, nginx will store it for 1h, because of these directives. I was thinking whether I should try proxy_cache, not sure what's the difference. In both fastcgi and proxy modules docs it says this: The cache honors backend's Cache-Control, Expires, and etc. since version 0.7.48, Cache-Control: private and no-store only since 0.7.66, though. Vary handling is not implemented. nginx version: nginx/1.1.19 Any thoughts? pd: I also have the reverse proxy that is offered by Symfony2 (which I turn off to use nginx's). The headers are interpreted correctly by it, so I think I'm doing it right.

  Read the article

• javascript doesn't seem to be able to post form data (nginx server w/ php-fpm)

  - by Jones

  So the situation is like so: I have a nginx server with php-fpm installed. All is well and the site scripts and all work perfectly. I am able to use html to POST form data and it works just fine. However, There seems to be be some correlation between javascript, the POST protocol and nothing happening. I cant seem to determine the issue. Example: I have a user login widget that uses javascript on submit the fields and POST the data to a backend auth script which returns a server message that then populates the login box saying something like "Login Successful" followed by reloading the page to properly enable content. Problem is, nothing happens when you hit submit. I do know the setup works because i had it working on apache before migrating. Also if it makes any difference, the server is a Amazon EC2 instance using the Amazon AMI. I really dont know where to start looking on this one, but below is my default.conf for the server: upstream backend_get { server 127.0.0.1:80 weight=1; } upstream backend_post { server 127.0.0.1:80 weight=1; } #Main website url server { listen 80; server_name server.com; #charset koi8-r; access_log logs/host.access.log main; error_log logs/host.error.log; location / { root /usr/share/nginx/html; index index.php index.html index.htm; if ($request_method = POST) { proxy_pass http://backend_post; break; } } location ~ \.php$ { #fastcgi_pass 127.0.0.1:9000; fastcgi_pass unix:/var/run/php-fpm/php-fpm.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } }

  Read the article

• Windows XP cannot read DVD burned on Ubuntu

  - by webcrawl

  The story : I have burned a DVD disc on Ubuntu using Brasero. When file burning was complete, I canceled the burning of checksum to DVD. Then I put that DVD on Windows XP (SP3) and copied all the files from DVD to the hard drive (no errors when copying). When that was done I discovered that all copied files are not readable. What is more, all the files on that DVD also shown to be not readable, even though all file names, directories were in their place. What I found out? Windows detect that the disc is in CDFS (CD-ROM File System). Disc is clean as new, have no scratches. All files while opened in Notepad++ look like "NULNULNULNULNUL" in one line. The size of files is normal. Other discs that are recognized as CDFS can be read with no problems. What I tried? Starting CDFS service in Windows registry. Result - a new device in Windows Device Manager (JUBS JGH2ZCT SCSI CdRom Device). Removing my CD/DVD device from Device Manager. Result - Windows restarted the system and reinstalled the driver. So... how to read the DVD, when I have no access to any other PC, any other OS?

  Read the article

• Windows 7 - Can't get my TV working as primary display with nVidia 7900GS

  - by Daniel Schaffer

  I just installed Windows 7 Ultimate 64 RTM (from MSDN) on my HTPC, which is connected to a 42" Magnavox LCD TV via component cables to my nVidia 7900GS. Everything was fine through the installation until I went to install the official driver from nVidia. Towards the end of the installation, the TV blinked off and wouldn't come back on. I went and got an LCD monitor and plugged it into a DVI port and the monitor came right up, but was automatically selected as the primary display. Now, if I set the TV to be the primary display, the TV just blanks until I hit escape to cancel the "settings have changed, do you want to keep them" dialog. Any suggestions? Update: I'm able to set the TV as the primary display using the Windows 7 "screen resolution" configuration panel. However, if I try to remove the LCD monitor either by unplugging it or using the configuration, the TV blanks out again. Update 2: This setup was working correctly in Vista Home Premium 32-bit. Update 3: I've uninstalled the nVidia driver and am using the driver that Windows Update installed. As much as this offends my geek sensibilities (must use the "right" driver!!), well, It Works™.

  Read the article

• Nginx load balancing and maintaining URLs

  - by Steve Klabnik

  I'm trying to use nginx as a load balancer, and it's working great. One problem, though. The load balancing box is at 123.123.123.123, and the backend box is 456.456.456.456. So I have this config: upstream backend { server 456.456.456.456; } server { listen 80; server_name 123.123.123.123; access_log off; error_log off; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://backend; } } This works great. I hit 123.123.123.123 in my browser, and the page comes up. But now the URL in the browser says http://456.456.456.456. Do I need to use a rewrite rule or something to keep the url correct? I don't want it to be different when going to different backed servers. None of the tutorials I've read have mentioned anything about this.

  Read the article

• Force request to miss cache but still store the response

  - by Tom Marthenal

  I have a slow web app that I've placed Varnish in front of. All of the pages are static (they don't vary for a different user), but they need to be updated every 5 minutes so they contain recent data. I have a simple script (wget --mirror) that crawls the entire website every 15 minutes. Each crawl takes about 5 minutes. The point of the crawl is to update every page in the Varnish cache so that a user never has to wait for the page to generate (since all pages have been generated recently thanks to the spider). The timeline looks like this: 00:00:00: Cache flushed 00:00:00: Spider starts crawling to update cache with new pages 00:05:00: Spider finishes crawling, all pages are updated until 1:15 A request that comes in between 0:00:00 and 0:05:00 might hit a page that hasn't been updated yet, and will be forced to wait a few seconds for a response. This isn't acceptable. What I'd like to do is, perhaps using some VCL magic, always foward requests from the spider to the backend, but still store the response in the cache. This way, a user will never have to wait for a page to generate since there is no 5-minute window in which parts of the cache are empty (except perhaps at server startup). How can I do this?

  Read the article

• Dell laptop keyboard doesn't work

  - by Tam

  I'm trying to fix my in-laws laptop, it's a Dell Studio 1745 that's running Windows 7 64 bit. The problem is that most of the keys on the keyboard do not work. The function keys work and the caps lock and numpad keys work, but no other keys do. If I hit the F2 key enough times when starting up, I can get to the BIOS, but after that even the function keys stop working. If I let it go all the way to the Windows login screen, I can see that the caps lock and num lock work - little images on screen actually appear, but they don't toggle the state of the key, i.e.,capslock is always off, numlock is always off. Using the fn+function combo works, so changing the brightness, etc. works fine. I'm stumped. I've tried disconnecting power and battery and leaving it for an hour or so before starting up but that hasn't helped either. Also - this might be a red herring - the touchpad is failing as well, the MS Device Manager says that it's failing with status 10, "unable to start device"

  Read the article

• Why am I experiencing random connection timeouts? (CentOS)

  - by Ryan

  I have a CentOS server setup that currently hosts several websites (all relative of each other in some form or another). As of recently throughout the day at the most random times the website speed will lag to a crawl and eventually hit a connection timeout. When I say random times this typically happens anywhere between 10am and 1pm usually, however, this morning this happened to me at 8am. I do not have a lot of familiarity with server knowledge as far as what I am looking for in this situation. What are some possible causes of why my server is slowing the websites down to a complete crawl or timing out? Are there specific things I should be checking for when this happens? I have noticed using: tail /var/log/httpd/access_log That usually when this down time occurs there are lot of IP addresses related to BingBot, Googlebot, and sometimes various bots or spiders that I am unfamiliar with. Could this be related and if so how can I avoid this from causing my websites to lag out? Thanks in advance for any help or advice. The websites that are timing out are built with PHP and use a MySQL database to display information.

  Read the article

• I just got a virus 6 mins ago, how? Situation.

  - by acidzombie24

  -Edit- for the people who say it isn't a virus. Norton does detect it as a virus, an icon was placed on my system tray and rkpg.exe is in my C: which was placed 6 min ago around the time my computer rebooted on its own causing me to lose data :@. Situation I on Windows XP, behind a Linksys router, I don't have DMZ on so nothing should be connecting to me. I had Firefox, MSN and Visual Studio opened. With C# I programmed a quick application to scan some pages with Internet Explorer. The site it was scanning was deviantART (which is pretty trustworthy), I doubt any banners there would hold a virus. I went to a suspicious site called freetxt.com but that was on Firefox and it didn't load the site. With an extra check I ping it and got this message "Ping request could not find host freetxt.com." The virus seems to be called braviax. Right now it brought up a message saying my computer may be infected? How on earth did it get in? I don't have uTorrent installed or any torrent or p2p applications. Nothing is installed on my computer that I haven't installed before and I know the exact time it installed because I see rkpg.exe on my C drive and my computer restarted on its own around the same time. For the previous 30 minutes actually the previous hour all I did was talk on MSN, not click any links (I went to freetxt on my own) and had that Internet Explorer thing running (which I programmed). How did it get in? I really doubt it came from a banner on deviantART and installed when I loaded the page with the webbrowser-control so something else may have happened? Is there any system defaults I should turn off? I have remote assistance off but even if it was on I shouldn't be infected due to the router not forwarding any ports?

  Read the article

< Previous Page | 269 270 271 272 273 274 275 276 277 278 279 280  | Next Page >