Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 293/1221 | < Previous Page | 289 290 291 292 293 294 295 296 297 298 299 300  | Next Page >

• Setting up Windows 2008 with VPN and NAT

  - by Benson

  I have a Windows 2008 box set up with VPN, and that works quite well. NPS is used to validate the VPN clients, who are able to access the private address of the server, once connected. I can't for the life of me get NAT working for the VPN clients, though. I've added NAT as a routing protocol, and set the one on in the VPN address pool as private, and the other as public - but it still won't NAT connections when I add a route through the VPN server's IP on the client side (route add SomeInternetIp IpOfPrivateInterfaceOnServer). I know I can reach the server's private interface (which happens to be 10.2.2.1) with remote desktop client, so I can't think of any issues with the VPN.

  Read the article

• HomeMade/DIY NAS solution

  - by MicTech

  Has anyone experience with building NAS (Network-attached storage) for home/small office using? What component would you recommend? Hardware CPU motherboard HDDs RAID controller etc. Software OS FTP HTTP etc.

  Read the article

• windows 7 no internet access

  - by Kyle

  Just did a fresh install of Windows 7, and the network and sharing center says no internet access. Disabling and enabling the adapter seems to fix the issue temporarily, but the internet stops working shortly after. I have installed the latest NIC drivers and have installed all Windows updates. I have also tried manually setting the ip/gateway/dns and running netsh int ip reset in an elevated command prompt. I am running Windows 7 Home Premium 64bit with a wired connection. I have searched for hours, but have found no working solutions. Does anyone have any ideas?

  Read the article

• ifcfg-eth* on CentOS 6.x, but for IPv6 only?

  - by Ray Hoffman

  Could someone kindly provide a skeleton ifcfg-eth0:[X] for creating an alias with a IPv6 address and no IPv4 address? Or, alternatively, what's the IPv6 equivalent of this: in /etc/sysconfig/network-scripts/ifcfg-eth0:1 DEVICE=eth0:1 ONBOOT=yes BOOTPROTO=static IPADDR=42.69.66.66 NETMASK=255.255.255.0 Or does this not even make sense in IPv6 space? I know that I can use, for example: IPV6INIT=yes IPV6ADDR=2600:4200::6900:6666:dead:beef But then do I need to specify that there is no IPv4 address associated with this alias? If so, how? And do I need to also specify the IPV6_DEFAULTGW? Or can it piggyback on the eth0 (unaliased) gateway, which is specifed, like with IPv4 aliases? EDIT: Answered my own question! The easiest way to accomplish this seems to be not to create an alias as with IPV4, but to specify, for example, IPV6ADDR_SECONDARIES=2600:4200::6900:6666:dead:beef on the script for the base interface, e.g. ifcfg-eth0.

  Read the article

• How do I create an ad hoc network in Windows 8?

  - by George Edison

  For the life of me, I can't figure out how to create an ad hoc wireless network in Windows 8. Here is what happens if I follow the steps from Windows 7: Right click the network icon and click "Network and Sharing Center": Click "Set up a new connection or network": Where is the option to create an ad hoc network? Therefore I have two related questions: Did I miss something? Is it in there somewhere and I just haven't found it yet? If this feature is not available, is there a tool somewhere I can use that provides this capability? Further information: I have an Intel Wireless WiFi 4965 AGN adapter. I tried the Intel PRO wireless tool and it didn't offer an ad hoc option.

  Read the article

• Airport Extreme and Windows PC via regular LAN (not WIFI)

  - by Mr AJL

  So I got an airpoort extreme, and everything works beautifully on the mac, but my windows 7 PC which is connected via a regular ethernet cable can't see any network. The Win7 PC says there's no cable connected. Any ideas? Is there some kind of setting you have to enable with the Airport utility? I looked everywhere but can't find anything. Thanks!

  Read the article

• Redhat 5.5: Multi-thread process only uses 1 CPU of the available 8

  - by Tonny

  Weird situation: Redhat Enterprise 5.5 (stock install, no updates, x64) on a HP z800 workstation. (Dual Xeon 2,2 Ghz. 8 cores, 16 if you count Hyper-threading. RH sees 16 cores.) We have an application that can utilize 1, 2 or 4 threads for heavy calculations. Somehow all these threads run on the same core at 100% load (the other 15 cores are nearly idle) so there is absolutely no benefit from the extra threads. In fact there is a slight slowdown as the threads get in each others way on the single core. How do I get them to run on separate cores (if possible)? Application is 64 bit. Can't change anything about the software except changing the threads setting. Is there some obscure Linux setting I can try to change? (I'm a True64 and Aix guy. I use Linux, but have no in depth knowledge of the process scheduling on Linux.)

  Read the article

• Fritz!Box IPv6-Address different than IPv6-Prefix

  - by kmindi

  In my Fritzbox it states the following: IPv6-Adresse: 2a02:8070:600::14b6:c7******, Gültigkeit: 100465/86065s IPv6-Präfix: 2a02:8070:62c:3200::/56, Gültigkeit: 100464/86064s I am not able to connect to IPv6 Addresses from computers configured by the fritzbox, because they get an address with prefix 2a02:8070:62c:3200::/56 but somehow the fritzbox does not route those addresses. Is this because the IPv6-Address is not in the prefix range? The address of the Fritzbox responds to pings, but my computers reached via various addresses from the prefix range do not (: PING 2a02:8070:62c:3200:28d****(2a02:8070:62c:3200:28d****) 32 data bytes From 2a02:8070:600:0:14b6*** icmp_seq=0 Destination unreachable: Administratively prohibited From 2a02:8070:600:0:14b6*** icmp_seq=1 Destination unreachable: Administratively prohibited From 2a02:8070:600:0:14b6*** icmp_seq=2 Destination unreachable: Administratively prohibited From 2a02:8070:600:0:14b6*** icmp_seq=3 Destination unreachable: Administratively prohibited blocked ping this is "view" from outside From inside the ping6 looks like this: traceroute -6 heise.de traceroute to heise.de (2a02:2e0:3fe:100::8), 30 hops max, 80 byte packets 1 fritz.box (2a02:8070:62c:3200:****) 0.787 ms 1.424 ms 1.702 ms 2 * * * ...... 30 * * *

  Read the article

• Dedicated NIC or dedicated port for iSCSI?

  - by Newt

  When spec'ing and configuring a machine that will utilise shared iSCSI storage, I've read a lot of documentation which suggests a dedicated network adapter should be used for iSCSI communication. That makes a lot of sense and I have no problem with it. The question I do have, is this - should that suggestion be taken to mean that a separate physical NIC should be used, or will a dedicated port/ports on a dual/quad port NIC be just as good? My suspicion is that simply using dedicated port(s) on a shared NIC would be just as good. Any input greatly appreciated.

  Read the article

• Cannot access virtual machine via ping from the physical host machine

  - by Kenni

  I'm installing a FreeBSD Server on VirtualBox. I set up the IP address (192.168.10.5) for the virtual server to run a mail server and the host computer(Windows 7) with 192.168.10.184. The two machines cannot communicate or connect to each other. I cannot ping from the virtual machine to the host and vice versa. The host machine connects to a LAN. I want the mail server to run frm a VMachine. I think it's a problem with the network configuration of the virtual machine.

  Read the article

• How to blacklist a problem wifi access point by MAC address in OSX

  - by Sam Alexander

  So I am a small mac-user cog in a larger windows-based network machine. The network here works fine for most everyone else (on PCs), but I have random timeouts and issues with the Wifi. Luckily, I have identified a few problem access points by MAC address (via their log messages in Console.app). Is it possible to tell my Airport on my Macbook to avoid those access points, and only speak with the access points who are far less touchy about me drinking the Apple kool-aid? All of the points are on the same network SSID.

  Read the article

• Snort network instruction Mac OS X

  - by Rasatavohary

  I'm trying to learn network intrusion detection. When I try to launch Snort, in IDS mode, I get this message (I'm running Mac OS X): Initializing Network Interface en1 ERROR: OpenPcap() FSM compilation failed: syntax error PCAP command: snort Fatal Error, Quitting.. How can I fix this problem?

  Read the article

• Router slowing my connection?

  - by Roberto

  I have a Linksys WRT54G and I pay for a 12Mbps connection. I've been testing my connection using speedtest.net for many days and always get 8Mbps. I called the support and they told me to bypass the router and test. I did it and got 16Mbps (much more than I pay for), so I thought "this guy just changed my speed so can he blame my router", and he blamed it. But to my surprise, everytime I bypass the router I get 16Mbps and when I use the router I get 8Mbps. Is this guy trolling me somehow (configuring the VOIP-modem-stuff to different profiles depending o the MAC address connecting to it) or is my router a POS? How can I find out? I don't know what's the thing the router connects to, it's a kind of VOIP adapter; the link is this one, but unfortunately I don't think you'll understand because it's in Portuguese. I know they can remotely connect to it, that's the origin of my conspiracy theory :) I just tested wired to the router and got 10Mbps (and still 8Mbps on wifi and 16Mbps without router) O_o I'm 5cm away from my router, so no obstacles to interfere, right? ------ UPDATE ------- It's a WRT54G V8, I'm using firmware v8.00.7 (will install 8.00.8 tomorrow, but I saw that it's only a minor fix to UPnP denial of service security vulnerability). Results: IPerf LAN-LAN: 80Mbps IPerf LAN-WLAN: 19Mbps (therefore we can ignore wireless issues/settings) I wasn't able to make the (W)LAN-WAN NAT-enabled test with IPerf, I get a connection refused error. I'm not sure if did it right: ran in server mode, configured router to forward that port to my IP and tried to connect to my internet IP that got from this site. I don't think there is a way to disable NAT using this firmware. Question: Let's suppose it's an underpowered hardware issue. Is it right to assume that custom firmwares could resolve the issue because they are possibly better implemented and would make better use of the router resources? I couldn't find any references pointing to wired performance improvements with the use of custom firmware.

  Read the article

• How to view all connections through Router

  - by Anton8000

  So what I need to know is how find out who has been visiting what websites when through the router. It is similar to being able to History on browsers, but people can clear their history, or use Incognito mode. However, surely any data would be sent through the router so even if the person did clear their history or use incognito mode, you would be able to see what they had sent through the router, and what the internet had sent back. Is there any way to view all the connections that the router manages, and store all the data that it sends and receives and put them into, for example, a log file so I could view which computer had viewed what website at what time?

  Read the article

• Why would cat6 connectors not work with cat5e patch cable?

  - by Lee Tickett

  I had a naff batch of cat5 connectors (the latching mechanism didn't work) so decided to order in some cat6 connectors in preparation for the inevitable upgrade. My existing reel of for making patch cables is cat5e utp stranded. I made up a few cables and tested them- none of them worked. I recrimped and still nothing. When i check them with a multi-meter not all pins are connected. This reel has always worked with the previous cat5 connectors so I tested the cat6 connectors on a reel of solid cat5e cable and they work fine. Any ideas what I might be doing wrong? Or what might be at fault? (cable/connectors) and how I can diagnose? Thanks Lee

  Read the article

• How can I close a port that appears to be orphaned by Xvfb?

  - by Jim Fiorato

  I'm running Xvfb on a FC8 Amazon EC2 image. On occasion Xvfb will crash (unable at the moment to find out the reason for the crash), and after crashing the TCP port will appear to be orphaned. I'm unable to get a PID to kill any process that may be using it. I'm starting Xvfb with: Xvfb :7 -screen 0 1024x768x24 & Examples of what I'm working with are below, the Xvfb port is (was) 6007: # netstat -ap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 *:ssh *:* LISTEN 1894/sshd tcp 0 0 *:6007 *:* LISTEN - tcp 0 352 ip-10-84-69-165.ec2.int:ssh c-71-194-253-238.hsd1:51689 ESTABLISHED 2981/0 udp 0 0 *:bootpc *:* 1817/dhclient udp 0 0 *:bootpc *:* 1463/dhclient Active UNIX domain sockets (servers and established) Proto RefCnt Flags Type State I-Node PID/Program name Path unix 2 [ ] DGRAM 871 668/udevd @/org/kernel/udev/udevd unix 2 [ ACC ] STREAM LISTENING 5385 1880/dbus-daemon /var/run/dbus/system_bus_socket unix 6 [ ] DGRAM 5353 1867/rsyslogd /dev/log unix 2 [ ] DGRAM 11861 2981/0 unix 2 [ ] DGRAM 5461 1974/crond unix 2 [ ] DGRAM 5451 1904/console-kit-da unix 3 [ ] STREAM CONNECTED 5438 1880/dbus-daemon /var/run/dbus/system_bus_socket unix 3 [ ] STREAM CONNECTED 5437 1904/console-kit-da unix 3 [ ] STREAM CONNECTED 5396 1880/dbus-daemon unix 3 [ ] STREAM CONNECTED 5395 1880/dbus-daemon unix 2 [ ] DGRAM 5361 1871/rklogd # lsof -i COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME dhclient 1463 root 3u IPv4 4704 UDP *:bootpc dhclient 1817 root 4u IPv4 5173 UDP *:bootpc sshd 1894 root 3u IPv4 5414 TCP *:ssh (LISTEN) sshd 2981 root 3u IPv4 11825 TCP ip-10-84-69-165.ec2.internal:ssh->c-71-194-253-238.hsd1.il.comcast.net:51689 (ESTABLISHED) Attempting to force the port closed with iptables doesn't seem to work either. iptables -A INPUT -p tcp --dport 6007 -j DROP I'm at a loss as to how to reclaim/free the port. From what I can tell, this port will remain in this state until the EC2 instance is shut down. So, how can I close this port so I can restart Xvfb?

  Read the article

• How to set Virtualbox appliance as webdev portable sollution?

  - by tenshimsm

  I just want to set a a Virtualbox virtual appliance to make it portable. Meaning that I'll enable a network config which will not need to be changed when I am using my laptop in a different network. I want the virtual machine to have internet access to keep it updated and be able to always have direct access from host using, for example, the IP 10.0.2.100 even when I am in a 192.168.0.1 network. So the first virtual network adapter will have a static ip (10.0.2.100) and the second will receive it from the DHCP. I don't know if 2 virtual adapters are needed or just one to accomplish that.

  Read the article

• SQL Server 2008 R2 transactional replication over VPN

  - by enashnash

  I'm having difficulty setting up replication over a VPN. I have a SQL Server 2008 R2, Enterprise Edition database on a Windows 2008 R2 Server. SQL Server is running on a non-standard port. I have set it up so that it is acting as its own distributor and have configured a publisher on this server. It is set as an updatable transational publication (yes, this is necessary). On this server, I have Routing and Remote Access enabled in order to be able to establish VPN connections. It is configured with a static IP address pool, of which the first in the range is always assigned to the server. I have assigned a test user a static address within this range (I don't know if this is necessary or not). All clients will be 2008 R2 versions, but could be SQL Express or standalone developer instances of the full product. I can establish a VPN connection from the client without problems and can see that the correct IP addresses are allocated. After connecting to the database to test that I can establish a connection, I realised that I needed to be able to connect to the database using the server name rather than an IP address - required for replication - which wouldn't work initially. I created an entry in the hosts file for the server on the client using the NETBIOS name of the server, and now I can connect to the server, from the client, using the SERVER\INSTANCE, PORT syntax, over the VPN. As it is the default instance on the server, I can also connect with simply SERVER, PORT syntax. After all that, I still get the following dreaded error: SQL Server replication requires the actual server name to make a connection to the server. Connections through a server alias, IP address, or any other alternate name are not supported. Specify the actual server name, 'SERVER\INSTANCE'. (Replication.Utilities). What have I missed? How do I get this to work? TIA

  Read the article

• Split horizon, route filtering, and having RIPv2 announce a non-attached route to host

  - by Paul

  Routers A, B & C live at 10.1.1.1, 10.1.1.2 and 10.1.1.3 on a /24 metro Ethernet subnet. Each router also has its own private subnet on another interface. Router B's private subnet links thru a firewall to a 10.20.20.0 network at another organization. Router B redistributes to A and C several static routes for hosts on 10.20.20.0. However, a new host 10.20.20.5/32 must be reached via a different path that goes through router C. I know that C can advertise this host-based route with no problem, but I'd like to keep all my 10.20.20.x static routes in one place. So, how can B tell A via RIPv2 to send packets for 10.20.20.5/32 to C? So far it looks like I need no ip split-horizon on router B's 10.1.1.2 interface, perhaps because B has already learned from C other routes with a next hop of 10.1.1.3. But how does RIPv2 split horizon with no auto-summary and network 10.0.0.0 really work? If B learns a route to ANY 10.x.x.x network or host from A or C, is that enough for split horizon to keep it from redistributing ip route 10.20.20.5 255.255.255.255 10.1.1.3? And if I want to suspend split horizon only for this one new host, how do I filter out the mess of regurgitated routes that B advertises when I try no ip split-horizon? Thanks much.

  Read the article

• Vista ICS issue

  - by Bill Grey

  I have a strange problem with Internet Connection Sharing on a laptop running Vista Business. This laptop is connected to the internet via the ethernet port, which goes to an ADSL modem. it is automatically assigned the IP address 192.168.1.50, and the modem/gateway is 192.168.1.1 My friends laptop is running Vista Home. Previously, I would create an ad hoc wireless network, enable ICS, and everything would be perfect. My friend would have internet access via this. However, something has now mysteriously broken. If I enable ICS on the wireless connection, it resets my Local Area Connection, assigning it the manual IP address of 192.168.0.1, which means my connection to the internet is destroyed. Both wireless adapters on each network are assigned auto configuration addresses, in the 168. range. They can see each other fine, but my friends laptop cannot access the internet via mine, even after I have restored the Local Area Connection settings. I understand the computer with ICS enabled must have the IP of 192.168.0.1, but previously, before whatever went wrong, my wireless adapter would be 192.168.0.1 and my friends computer would get an IP via DHCP. I have also tried setting static IP address and making a bridge, none of which works. How can I fix this problem, and prevent enabling ICS from touching my Local Area Connection? Both machines have no firewall, have appropriate settings etc...

  Read the article

• SQL instance through F5 BigIP VIP

  - by Sam

  We have a SQL 2008 instance Server01\instance02. The port is set to 1466. We've set up a VIP named Server1 Attempting to connect to Server1\instance02 does not work. Server1,1466 does work. We have ports 1433, 1434 and 1466 open. Can we configure this to be able to use the name without any changes to the SQL client. Thanks!!

  Read the article

• Localhost problems on Mac OS X 10.7

  - by Maya

  Sorry for the duplicate post ( http://stackoverflow.com/questions/9720871/localhost-problems-on-mac-os-x-10-7 ), but I got the advice that this is a better place to ask my question: I want to access a mysql server remotely over ssh. So I used port forwarding to access the remote 3306 port on my localhost as 8383. The ssh connection can established successfully. But when I want to telnet onto port 8383 on localhost I get the following error: ~: telnet 127.0.0.1 8383 Trying 127.0.0.1... telnet: connect to address 127.0.0.1: Connection refused telnet: Unable to connect to remote host I tried the same on a friends Laptop (also Mac OS X 10.7) and it worked fine, so it is very unlikely that the ssh connection is the problem. I assume it has something to do with my local network configuration. I turned off IPv6, just in case. My /etc/hosts looks like this: 127.0.0.1 localhost 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost I would greatly appreciate any help. Please point me in the right direction if this is not the right place to ask this question.

  Read the article

• Router behind router network setup

  - by optimus

  My relative has bought a router instead of a switch which causes remote-access control issues on his network. His existing network has a 1st router where all PCs are connected via LAN cables. The 2nd router connnects to the 1st router and the remaining PCs are connected to the 2nd router via LAN cables. Normally, I would perform remote-access to help him out with some task. Now it seems all services behind the 2nd router are unavailable to me. How can I resolve this issue?

  Read the article

• Network cabling with multiple patch panels?

  - by dannymcc

  I am in the very early stages of planning a network cabling upgrade in our office, mainly to upgrade the old cables from Cat5 to either 5e or 6. I am also planning on upgrading all of our 10/100 switches to 10/100/1000 switches. I would like to have three small wall mounted cabinets spread around the building, each with a patch panel and switch. These would all lead back to our server room. The question is; should I have two patch panels in each wall cabinet, one with 24 or 48 ports that are connected to a matching patch panel in the server room. The second patch panel would then link to each device in that cabinets area. Then I wouldn't put a switch in the small cabinets. All switching would be done in the server room. Or, should I have one main cable from the server room to each of the cabinets - plugged straight into the switch and the patch panel is for devices in the cabinets area? I hope that makes sense!

  Read the article

• Virtualbox two networks slow

  - by Petr Marek

  I am running an Ubuntu server guest on Win 7 guest, and am running a webrick server (RoR dev). If I have just a host-only network, everything works fine and the browser response is instant. However, if I add a second network (NAT), so that the server can connect to the internet (for various updates etc.), the host-to-guest access gets really slow. I can't use the bridge connection. I am using the port 3000 (RoR Webrick server) and connecting to the guest via internet browser on this port (eg http://192.168.56.102:3000). Any idea, what could be causing this? If I ping the IP from host console, I get < 0ms. Here are the settings (relevant info is in english; Povoleno vše is Everything is allowed):

  Read the article

< Previous Page | 289 290 291 292 293 294 295 296 297 298 299 300  | Next Page >