Search Results

Search found 24514 results on 981 pages for 'connection manager'.

Page 299/981 | < Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >

• Ethernet interface number changed, and old one does not exist, but does not leave IP address

  - by Sagar

  I have a virtual machine with Mandriva 2007.0 (yes, old - unfortunately we do not have a choice here). Anyway, the problem: Before reboot: active network interface = eth0. No other interfaces present, and network manager confirms this. Static IP address set to 172.31.2.22. No issues, everything working properly, routing et al. -------Reboot--------- After reboot: active network interface = eth1, with a DHCP address. Network manager shows eth0 as disconnected, and not connectable. When I try to set eth1 up with the static IP address (same one), it says "In Use". I then tried ifconfig eth0 172.31.2.29 just to free it up from the eth0 interface so I could use it with eth1 (since this is connected). Result: ifconfig eth0 172.31.2.29 SIOCSIFADDR: No such device eth0: unknown interface: No such device Nothing else changed. Any ideas what could be happening, or at least how I can get my IP address back?

  Read the article

• How to get headphones and speakers working at the same time?

  - by Borek

  I have a Gigabyte P55-UD3 motherboard which comes with a Realtek sound card and audio header for the front panel. My headset is permanently connected to the front panel (mic in, headphones in) and I also have speakers connected at the rear of the computer. What I want to achieve is that both the headphones and the speakers work at the same time. On my old PC with Realtek, I was able to do this by clicking "Device advanced settings" in the Realtek HD Audio Manager and then clicking "Make front and rear output devices playback two different audio streams simultaneously" and then doing some reassigning of front/rear settings in the Realtek Audio Manager (can't remember the details). But that doesn't seem to be working now - either the speakers play sounds or the headphones, not both at the same time. To pose the question differently, Windows plays the sounds on the "default device". I'd like to make both headphones and the speakers kind of like the default devices.

  Read the article

• How to kill unkillable Python-processes running as root

  - by Andrei

  I am experiencing an annoying problem with sshuttle running it on 10.7.3, MBA with the latest firmware update -- after I stop it (ctrl+c twice), or loose connection, or close the lid, I cannot restore it until I restart the system. The restarting takes notably more time, than it would normally take. I have tried to flush ipfw rules - not helping. Could you advice me how to restore sshuttle connection (without restarting os)? The following processes remain running as root, which I do not know how to kill (tried sudo kill -9 <pid> with no luck): root 14464 python ./main.py python -v -v --firewall 12296 12296 root 14396 python ./main.py python -v -v --firewall 12297 12297 root 14306 python ./main.py python -v -v --firewall 12298 12298 root 3678 python ./main.py python -v -v --firewall 12299 12299 root 2263 python ./main.py python -v -v --firewall 12300 12300 The command I use to run proxy: ./sshuttle --dns -r [email protected] 10.0.0.0/8 -vv The last message I get trying to restore the connection: ... firewall manager: starting transproxy. s: Ready: 1 r=[4] w=[] x=[] s: < channel=0 cmd=PING len=7 s: > channel=0 cmd=PONG len=7 (fullness=554) s: mux wrote: 15/15 s: Waiting: 1 r=[4] w=[] x=[] (fullness=561/0) >> ipfw -q add 12300 check-state ip from any to any >> ipfw -q add 12300 skipto 12301 tcp from any to 127.0.0.0/8 >> ipfw -q add 12300 fwd 127.0.0.1,12300 tcp from any to 10.0.0.0/8 not ipttl 42 keep-state setup >> ipfw -q add 12300 divert 12300 udp from any to 10.0.1.1/32 53 not ipttl 42 >> ipfw -q add 12300 divert 12300 udp from any 12300 to any not ipttl 42 Update: $ ps -ax|grep python 1611 ?? 0:06.49 python ./main.py python -v -v --firewall 12300 12300 48844 ?? 0:00.05 python ./main.py python -v -v --firewall 12299 12299 49538 ttys000 0:00.00 grep python

  Read the article

• How to run Android-x86 project's ISO in VirtualBox with ethernet?

  - by Shiki

  I managed to find a way just days ago, but I had to leave my other PC and now I have no clue how to get it working again. Basically you have to get the image, then install it in a VirtualBox guest. Now the problem is ... when you launch your VM, there is no internet connection. No with NAT or Bridged. Tried all the network cards too. Since internet connection is crucial for Android development, I have to get this thing working. (As I said, I managed to fix it once.) I'm using: - The 4.0 RC1 images from Android-x86 - VirtualBox - Eclipse 4.2 Juno with the latest Android ADT - Android SDK v18 - upgraded to 19 via the Package manager. Now I seen a lot of different builds on the net, about different Android builds for VirtualBox. I have checked Buildroid for example, but there is no network connection. I have imported the virtual machine just as the howto said. The extension package is also installed and it's up to date.

  Read the article

• Windows 7 - Wireless Signal Good - Internet Often Says Limited or No Activity

  - by Anthony Trilussa Pizzo

  Hi - I have a New Dell Studio XPS latop that I hooked up in early January of 2010. The Dell Studio XPS laptop is connected to my wireless router (Belkin Wireless N). The router was purchased in Februaru of 2010 because I thought my router was bad (A D-Link router). Comcast is my ISP. Everyday, at random times, the internet will have a good signal (according to the little Win 7 icon on the taskbar) but I will receive a message saying limited or no internet access and I cannot access the internet. I have the internet setup to automatically get an IP and I did the IPCONFIG release / renew but with no success. I even had a WiFi enabled Blackberry right next to my computer and whenever the computer loses an WiFi connection, so does the Blackberry. The router isnt't bad, because the old router did the same thing - giving me limited or no internet access while working sometimes. I also tried using two other laptops in same physical position as my Dell Studio XPS laptop and they have the same problem. I am going crazy trying to figure this out as I have called the Router Company (Belkin), my ISP (Comcast), and my computer maker (Dell). Can anyone offer some suggestions and I can try them as we work through this and maybe one of the suggestion will be right one. Thanks in advance for even reading my problem. I searched for a problem similar to mine on the internet, but I have not been able to keep a steady internet connection. (Side note - I used to have an IBM thinkpad laptop and D - Link router and for years that wireless connection worked FLAWLESSLY, with the same physical set up - the laptop in my bedroom, and the router in the basement.)

  Read the article

• Why is my cat5e cable not okay?

  - by torbengb

  My LAN cable seems to work (indicator LED lights up) but the computer can't find a connection. What's wrong? Setup: I had to run a network cable from a router in one room to a computer to another room, through a hole in the wall that was too small to pass the RJ-45 plug through. The plug was cut off and the cable passed through the wall. Then a new plug was crimped on using this detailed explanation. The connection didn't work because the (factory-made!) plug in the other end used a non-standard wire order. I crimped a new plug on again, using the exact same order of the factory-made plug. The LED indicator lights up on both ends, but the computer cannot find a connection. What can be wrong? How can I find out? I don't have a cable tester. By visually inspecting my new plug, I think it's good; the wire order matches the other end, and all wires are all the way inside the plug and reach the connector piece. I've used the cable before (with both factory-made ends) so i don't think that the cable itself has a defect.

  Read the article

• Remote Sending of Emails via SMTP/EXIM Issue

  - by Christian Noel

  I have been encountering a problem when sending messages via EXIM. Here is the scenario: I have 2 servers lets just say host1.com = where all my apps and programs are hosted. host2.com = is another server which handles some apps but is also my smtp mail server. whm and cpanel are installed in both hosts as well as exim. right now, messages are being sent out as [email protected] to clients. host1.com uses the [email protected] so that it can send messages outbound as well. here's the problem, after a few hours from a fresh reboot of host1.com, sending messages from host1.com is no longer possible because i encounter an error that states: system/vendor/swift/Swift/Connection/SMTP.php [309]: The SMTP connection failed to start [tls://mail.host2.com]: fsockopen returned Error Number 110 and Error String 'Connection timed out'` also note that this was working fine earlier (like 10 hours ago) but then it suddenly fails. everytime i restart the host1.com then sending messages will work again. i have checked logs and traces but to no avail the only means of fixing this problem is restarting host1.com.

  Read the article

• Cisco ASA: Routing packets based on where the connections started from

  - by DrStalker

  We have a Cisco ASA 5505 (version 8.2(2)) with three interfaces: outside: IP address 11.11.11.11, this is the default route inside: IP address 10.1.1.1, this is the local subnet newlink: 22.22.22.22, this is a new internet connection. We need to move VPN users from the 11.11.11.11 address to the 22.22.22.22 address, and we're using SSH on the ASA as to test and sort out the routing. The problem we have is this: If we define a particular IP as being on a static route out the newlink interface then it can SSH to 22.22.22.22 fine. If we do not define a static route then the traffic hits the ASA, but the return traffic does not come back over newlink; presumably it gets sent over the outside interfcae as that is the default route. We can't define a static route for each remote endpoint because there are dialup VPN users, who obviously change IP a lot What we need to do is configure the ASA so if a connection comes in on the newlink interface then the outgoing packets for that go over the newlink interface, not the default route. With iptables this should be do-able by marking the connection and doing mark-routing, but what is the equivalent for a Cisco ASA?

  Read the article

• Middle Mouse Button does not work in XFCE / Arch Linux

  - by Alp

  I have the XFCE desktop manager installed on my Arch Linux system. With E17 (Enlightenment desktop manager) i had no problems with my mouse: all buttons worked correctly out of the box. But in XFCE my middle mouse button does not fire an event at all (no output with xev). Evdev seems to identify my mouse correctly (Razer Deathadder) because it echoes its name in the xorg logs. I have no idea what could cause this and how to debug the problem. I start both e17 and xfce with startx. Here is my ~/.xinitrc: exec startxfce4 --with-ck-launch #exec enlightenment-start

  Read the article

• Ubuntu not connecting to network in Hyper-V

  - by soandos

  I am unable to connect the Ubuntu guest (both 12.10 and 12.04) to the internet via hyper-V. Here is what I have done so far (with much thanks due to @Kronos's blog post on the topic): Created a switch in the switch manager with connection set to external, selected my wifi card (Intel Centrino Ultimate-N 6300 AGN). If it matters, the Microsoft Filtering Platform is checked under extensions. Added this switch to my Ubuntu guest. I also tried a different wireless card (Aethros 9285) same issue. Connecting through my wired card works just fine (assume that I select that card, and I am wired in of course). Making it a legacy network adapter does not fix the issue. Ubuntu can see this connection, but is unable to connect to it. What follows is what I attempted to do to get Ubuntu to connect: Start and restart the network manager Restart the machine Verify that it could in fact see the adapter (resulted in device not ready a few times) How can I get this to work properly?

  Read the article

• stunnel client uses improper SNI when talking to Apache

  - by Huckle

  I have stunnel listening on port 80 and acting as a client connecting to Apache listening on port 443. Configuration is below. What I'm finding is that if I attempt to connect to localhost:80 the connection is fine but if I connect to 127.0.0.1:80 When I check Apache's logs it indicates that stunnel is using localhost as the SNI both times, but the HTTP request lists localhost in one case and 127.0.0.1 in another. Is it possible to tell stunnel to either use whatever is in the HTTP request or to somehow configure two clients each with different SNI values? stunnel.conf: debug = 7 options = NO_SSLv2 [xmlrpc-httpd] client = yes accept = 80 connect = 443 Apache error.log: [error] Hostname localhost provided via SNI and hostname 127.0.0.1 provided via HTTP are different Apache access.log: "GET / HTTP/1.1" 200 2138 "-" "Wget/1.13.4 (linux-gnu)" "GET / HTTP/1.1" 400 743 "-" "Wget/1.13.4 (linux-gnu)" wget: $wget -d localhost ---request begin--- GET / HTTP/1.1 User-Agent: Wget/1.13.4 (linux-gnu) Accept: */* Host: localhost Connection: Keep-Alive ---request end--- $wget -d 127.0.0.1 ---request begin--- GET / HTTP/1.1 User-Agent: Wget/1.13.4 (linux-gnu) Accept: */* Host: 127.0.0.1 Connection: Keep-Alive ---request end--- edit: Apache Config Nothing out of the ordinary, it's just a virtual host listening to 443 <VirtualHost *:443>

  Read the article

• IIS7.5 Windows Authentication missing providers menu item (ntlm)

  - by Alex

  Hello, I'm trying to enable NTLM authentication on a Windows Server 2008 R2 machine with IIS 7.5 for a specific file in my web root. I've been following these instructions http://docs.moodle.org/en/NTLM_authentication#IIS_Configuration In the IIS Manager I open the Authentication module, disable anonymous authentication and enable Windows Authentication however according to every post I can find on the matter I should have a 'providers' option appear but I don't. I've double checked in Server Manager that the 'Windows Authentication' security feature is enabled for IIS. Any help anyone can offer would be great, Thank you!

  Read the article

• How to use my computer as a Headset device for my phone with Bluetooth?

  - by TheJelly

  I want to extract the audio from my phone (the analog TV and FM/AM receiver mainly) and play it through my computer speakers. There is a headphone jack but it is of non-standard size (probably a micro-jack) and I do not have access to a shop that sells that kind of equipment in my area so doing this with Bluetooth is the only solution I can foresee. Both my laptop and my phone support A2DP but for some reason the service (from the phone) does not show up while I add a new connection and the phone does not let me initiate a connection with any other profile except FTP (although it detects other services in the service list like A2DP and works perfectly fine with other profiles like DUN, HID, OPP, SSP if the connection is started through the computer). I am currently using the latest version of the Toshiba stack, I have tried using WIDCOMM but it refuses to install drivers for both the internal Bluetooth (which is a Broadcom device) and the USB Bluetooth that I use on my desktop. The standard Microsoft stack (generic driver) does install but it does not work with both of my devices as they do not detect any Bluetooth devices when scanning. With BlueSoleil (the default stack that came with the USB Bluetooth) I could set my device as "headset" instead of only "laptop/desktop", and this allowed both my phones to detect my laptop as a device they can use as a headset, but the problem with this stack was that only the older phone could actually connect to my laptop and that the internal Bluetooth could not be used. Basically, I want to set the device type as a "headset" for my phone using the Toshiba stack like I did with BlueSoleil. Is there any way this could be done? Thanks. Image: Device type selection http://i.stack.imgur.com/drjC6.jpg

  Read the article

• just curious if anybody every tried this- hyper-v r2

  - by tony roth

  I have a server that san boots that I want to p2v. I have many options disk2vhd, scvmm etc but I was thinking about cloning the lun (flexclone, netapp) presenting it to my hyper-v r2 server. Within the hv manager do a create new disk then have it copy the cloned lun to a vhd file. Then do the bcdedit\bootsect stuff to it. Should work right? I'm also curious if anybodys booting vhd's that are on bootable luns? I've booted native vhd's just fine was just curious about the running them off a bootable lun. I think that this has quite a few advantages like instant p2v etc.. any thoughts on this? hmm dang as I was typing this I realized that I should not use the hv manager new disk copy routine, I should just disk2vhd the mounted lun. This has advantages in that it should be a lot faster!! thanks

  Read the article

• Sendmail Sends but never Delivers

  - by Jeremy

  I have tried 10 different emails hosted at Google, Yahoo!, GoDaddy, and some that are privately hosted, and each time I get the following errors. I have blocked sensitive information, but you will be able to see the errors. Feb 16 17:06:50 xxxxx sendmail[31824]: o1GM6ovJ031824: [email protected], ctladdr=www-data (33/33), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30054, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (o1GM6oJo031825 Message accepted for delivery) Feb 16 16:54:19 xxxxx sendmail[31625]: o1GLsJPP031625: [email protected], ctladdr=www-data (33/33), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30097, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (o1GLsJah031626 Message accepted for delivery) Feb 17 09:05:52 xxxxx sm-mta[10620]: o1H6Z3jM005734: to=<[email protected]>, ctladdr=<[email protected]> (33/33), delay=07:30:49, xdelay=01:15:36, mailer=esmtp, pri=571331, relay=aspmx3.googlemail.com. [209.85.222.4], dsn=4.0.0, stat=Deferred: Connection timed out with aspmx3.googlemail.com. Feb 17 10:35:23 xxxxx sm-mta[12828]: o1HEZwn8011833: to=<[email protected]>, ctladdr=<[email protected]> (33/33), delay=00:59:25, xdelay=00:12:36, mailer=esmtp, pri=300353, relay=aln-mailrelay.att.net. [12.102.252.75], dsn=4.0.0, stat=Deferred: Connection timed out with aln-mailrelay.att.net. If you take a look, they all send, but then (HOURS later) I get an error "stat=Deferred: Connection timed out with {server}". I'm at my wits end, because I use this same setup on each of my servers, and they all work.

  Read the article

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• Intranet Design and Development Book Recommendations

  - by Russ Giddings

  Hi All, Can anyone recommend any good books on Intranet planning and implementation for the business professional / manager? Thanks Russell

  Read the article

• Enable anonymous access to report builder in reporting services 2008

  - by ilivewithian

  I have a 2008 reporting services server installed on windows 2003 server. I am trying to allow anonymous access to the report builder folder so that my users do not have to select the remember password option when they login, if they are wanting to use the report builder. All I have found so far is that I should be able to do this with the IIS manager, but that only seems to work for reporting services 2005. Reporting services 2008 does not show up in the IIS manager, enabling anonymous access seems to be hidden somewhere else. How do I enable anonymous access to report builder in reporting services 2008?

  Read the article

• Application Compatibility Clients do not show in MSSQL database, but do show in \AppCompat\

  - by rjt

  Application Compatibility Clients are not denied access to the central MSSQL database, but are able to leave their own files in the \AppCompat\ share. The only computer that shows up in the "Microsoft Application Compatibility Manager" database is the the machine i initially created the .MSI installer from. The MSI successfullly pushed out via GPO and like i said there are tons of file in the \AppCompat\ share from many different computers. But only 1 pc shows up in the "Data Collection Manager" database, so i only have data from one machine. i could manually add all these machines (ADNETBIOSNAME\MACHINENAME221$) to the MSSQL AppCompat db permissions list or use an SQL command to do so in batch, but i suspect i must have missed something. Do you manually edit the MSI to set the credentials?

  Read the article

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• How to point a Wordpress registered domain to github pages?

  - by Dave Castillo

  I'm trying to use a CNAME file in my git hub project to point to my wordpress registered domain name. E.g. example.com to point to myusername.github.com. I read Github-Setting up a custom domain and it tells me to point the domain to their servers: For a TLD like example.com, you should use an A record pointing to 204.232.175.78: But in the wordpress domain manager I only get the option to specify a nameserver like this: NS1.WORDPRESS.COM NS2.WORDPRESS.COM Inputting 204.232.175.78 in the wordpress manager give me an "invalid TLD." What am I doing wrong and how can I troubleshoot this issue?

  Read the article

• SQL Server 2008 Remote Access

  - by Timothy Strimple

  I'm having problems connecting to my SQL Server 2008 database from my computer. I have enabled remote connections as described in this answer (http://serverfault.com/questions/7798/how-to-enable-remote-connections-for-sql-server-2008). And I have added the ports listed on the microsoft support page to our Cisco Asa firewall and I'm still unable to connect. The error I'm getting from the SQL Management Studio is: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: TCP Provider, error: 0 - A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.) (Microsoft SQL Server, Error: 10060) Once again, I have double and triple checked that remote connections are enabled under the database properties and that TCP is enabled on the configuration page. I've added tcp ports 135, 1433, 1434, 2382, 2383, and 4022 as well as udp 1434 to the firewall. I've also checked to make sure that 1433 is the static port that is set in the tcp section of the database server configuration. The ports should be configured correctly in the firewall since http/https and rdp are all working and the sql server ports are setup the same way. What am I missing here? Any help you could offer would be greatly appreciated. Edit: I can connect to the server via TCP on the internal network. The servers are colocated in a datacenter and I can connect from my production box to my development box and vice versa. To me that indicates a firewall issue, but I've no idea what else to open. I've even tried allowing all tcp ports to that server without success.

  Read the article

• Can't login into Fedora 14 (XFCE) desktop. For the second time.

  - by bubba88

  Hello. I'm experiencing a problem with my Fedora 14 XFCE spin, which doesn't seem to let me pass the login screen: I enter my password for my user record, authentication passes (no 'Authentication Failure' message, which was when I tried to login as 'root' without root login enabled), and the screen becomes black (command line) for a couple of seconds and (voila!) my login screen emerges again. I did nothing to cause that, it just suddenly logged me out when I was editing window manager settings via XFCE's built-in GUI utility (choosing window decorations style, from the listbox on the left) For the first time, I had to boot from live CD and do a fresh install, but I don't really want to do that again :) Is there some way to repair this (maybe login via command line and reset window manager settings, I don't know really)? Thank you very much in advance!

  Read the article

• IIS6 - Change the language to English

  - by user93353

  I have a Windows 2003 VM Image which was created by a Swedish Windows Install. Afterwards the language settings of the machine was changed to English. However, I just added IIS6 Windows component to the machine (from Add/Remove Programs) - IIS6 is not in English. It's in Swedish. IIS Manager's Menu options are in English, but the Title Bar uses hanteraren(Swedish for Manager). The IIS Error pages come in Swedish. How do I get IIS's default language back in English.

  Read the article

• Problem installing Cardbus/PCMCIA drivers (USB 2.0 2-port)

  - by Carl

  I obtained the drivers from the manufacturer for my HT-Link NEC USB 2.0 2-port Cardbus card. When I plugged in the card before I got the drivers, 3 new entries showed up in the Device Manager - two "NEC PCI to USB Open Host Controller" and one "Standard Enhanced PCI to USB Host controller." With the card plugged in, I uninstalled those two drivers. I then removed the card. I copied the new drivers to c:\windows\system32\drivers and the .inf file to c:\windows\inf. I also copied the drivers & inf to a new directory called c:\windows\drivers\ousb2. I reinserted the card. Windows automatically installed the same drivers as before. I selected 'update driver' on the "NEC PCI to USB..." entry and didn't see any other options. I then selected 'have disk' and pointed to c:\windows\drivers\ousb2 and got a message "The specified location does not contain information about your hardware." I then selected 'update driver' on the "Standard Enhanced PCI to USB...," and manually selected "USB 2.0 Enhanced Host Controller" (OWC 4/15/2003 2.1.3.1). Windows then automatically found a USB root hub, and I manually selected "USB 2.0 Root Hub Device" (OWC 4/15/2003 2.1.3.1). Now there are two sections in the Device Manager titled "Universal Serial Bus controllers." I plugged in my external USB hard disk adapter, and "USB Mass Storage Device" was added to the first set. Here's how it looks (w/drivers from the properties): [Universal Serial Bus controllers] Intel(R) 82801DB/DBM USB 2.0 Enhanced Host Controller - 24CD (6/1/2002 5.1.2600.0) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C2 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C4 (7/1/2001 5.1.2600.5512) Intel(R) 82801DB/DBM USB Universal Host Controller - 24C7 (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) NEC PCI to USB Open Host Controller (7/1/2001 5.1.2600.5512) USB Mass Storage Device USB Root Hub (7/1/2001 5.1.2600.5512) (5 more USB Root Hubs - same driver) [Universal Serial Bus controllers] USB 2.0 Enhanced Host Controller (OWC 4/15/2003 2.1.3.1) USB 2.0 Root Hub Device (OWC 4/15/2003 2.1.3.1) When I unplug the card the two "NEC PCI to USB..." entries in the first set disappear, and the whole second set disappears. (I unplugged the hard disk adapter first...) The hard disk adapter still doesn't work in that Cardbus card with the new drivers. I don't think the above looks right - a second set of USB controllers listed in the Device Manager, and the NEC entries still in the first set, and the the USB mass storage device still in the first set. Any help appreciated. (Windows XP PRO SP3 w/all current updates.)

  Read the article

< Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >