Search Results

Search found 11935 results on 478 pages for 'knowledge module'.

Page 299/478 | < Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >

• How to rsync a large file, with as little CPU and bandwidth expense as possible?

  - by Johan Allgoth

  I have a 500 GB file that I plan on backing up remotely. The file changes often. I'll be rsyncing it from a desktop to a server. Both can run rsync client or server. What is the proper command for this? The ones I've tried sofar has been taking forever or simply acted strange. Example and results: rsync -cv --partial --inplace --no-whole-file /desktop/file1 myserver.com::module/file1 Seems to work, but only if I do it twice (?!). Also, slow. Does the above command do the checksumming on both computers, or only on the sending one? Is it correct otherwise?

  Read the article

• Multiple VLANs on a single subnet

  - by mstaessen

  I would like to establish the setup shown below. The image is taken from (http://gcharriere.com/blog/?p=620) and explains how to set this up on a brocade device. I would like to use an ubuntu server to do the routing. Right now, the switch and the server/router are connected with a trunk and the server uses the vlan package, kernel module and (inner) subnets for routing. I would like that: no IP addresses get lost in the subnetting (outer subnet is /26, inner subnets are /28) I don't want the rigorous subdivision of my outer subnet. I want to assign a VLAN to any IP in the outer subnet. How do I need to configure my interfaces? What is the "ubuntu" translation of "ip follow ve"? Thanks!

  Read the article

• Apache fails silently after installation of MapServer 6.2.0

  - by wnstnsmth

  I've recently compiled MapServer 6.2 on a CentOS 6.3 machine, using ./configure --with-ogr=/usr/bin/gdal-config --with-gdal=/usr/bin/gdal-config --with-proj=/usr --with-geos=/usr/bin/geos-config --with-postgis=/usr/bin/pg_config --with-php=/usr/include/php --with-wfs --with-wfsclient --with-wmsclient --enable-debug --with-threads --with-wcs --with-sos --with-gd --with-freetype=/usr/bin --with-jpeg --with-cairo --with-curl if that is of interest, anyway. So after that, Apache/2.2.15 silently fails to restart, i.e. when apachectl graceful, it says "httpd not running, trying to start". There is nothing of interest in the Apache errors_log, /var/log/messages, and it is weird because so far it has always worked. Restarting the machine multiple times did not solve the problem. Some other stuff I did: [root@R12X0210 cgi-bin]# service httpd status httpd is stopped [root@R12X0210 cgi-bin]# ps aux|grep httpd root 1846 0.0 0.0 103236 864 pts/0 S+ 12:11 0:00 grep httpd I suspect this might have something to do with a php module that was altered/added by MapServer, but I don't really know... I don't even know how to properly debug this.

  Read the article

• iis7 .net webservice 404 error

  - by agilenoob

  I have a webservice /test/Service1.asmx in the same folder as a page /test/test.aspx. The page works fine but I get the message bellow for the services in the same location. I know the file is there and the url is correct, and I have added the script module and managed handler as well. If anyone knows what I'm missing here I'd appreciate it Server Error in '/' Application. The resource cannot be found. Description: HTTP 404. The resource you are looking for (or one of its dependencies) could have been removed, had its name changed, or is temporarily unavailable. Please review the following URL and make sure that it is spelled correctly. Requested URL: /test/Service1.asmx Version Information: Microsoft .NET Framework Version:2.0.50727.4200; ASP.NET Version:2.0.50727.4016 FAILED REQUEST LOG: ModuleName ManagedPipelineHandler Notification 128 HttpStatus 404 HttpReason Not Found HttpSubStatus 0 ErrorCode 0 ConfigExceptionInfo Notification EXECUTE_REQUEST_HANDLER ErrorCode The operation completed successfully. (0x0)

  Read the article

• Xdebug 2.0.5 with Zend Server CE PHP5.2.12 possible?

  - by notbrain

  I'm using Zend Server CE with PHP 5.2.12 on OSX Snow Leopard and want to use Xdebug. I've turned off Zend Data Cache, Zend Optimizer+, and Zend Debugger in the console. When I run $ cd ~/Downloads/xdebug-2.0.5 $ /usr/local/zend/bin/phpize I get Configuring for: PHP Api Version: 20041225 Zend Module Api No: 20060613 Zend Extension Api No: 220060519 The PHP API Version, 20041225, seems to be off from the documentation (aka wrong). When I continue installation with $ ./configure ---with-php-config=/usr/local/zend/bin/php-config $ make $ sudo make install The installed xdebug.so seems to be the wrong one. Which version of xdebug do I need for this PHP API version? The Zend API numbers are ok. I'm just confused at why the PHP API Version doesn't match. PHP Warning: PHP Startup: Unable to load dynamic library '/usr/local/zend/lib/php_extensions/xdebug.so' - (null) in Unknown on line 0 PHP 5.2.12 (cli) (built: Feb 17 2010 13:39:36)

  Read the article

• Elastic beanstalk access private git repo

  - by user221676

  I am trying to currently add an ssh key to my elastic beanstalk instances using .ebextensions commands. The keys I have stored are in my application code and I try to copy them to the root .ssh folder so I can access them when doing a git+ssh clone later here is an example of the config file in my .ebextensions folder packages: yum: git: [] container_commands: 01-move-ssh-keys: command: "cp .ssh/* ~root/.ssh/; chmod 400 ~root/.ssh/tca_read_rsa; chmod 400 ~root/.ssh/tca_read_rsa.pub; chmod 644 ~root/.ssh/known_hosts;" 02-add-ssh-keys: command: "ssh-add ~root/.ssh/tca_read_rsa" the problem is that I get is an error when attempting to clone the repo Host key verification failed. I have tried many ways of try to add the host to the known_hosts file but none have worked! The command that is doing the clone is npm install as the repo points to a node module

  Read the article

• Samba as a PDC and offline authentication

  - by Aimé Barteaux

  Say I have a Windows laptop which has been connected to a domain. The domain has a Samba server as a PDC. Now say that I move the laptop outside of the network (the network is completely inaccessible). Will I be able to logon into accounts I have accessed before on the laptop (through GINA)? Update: Looking at the smb.comf documentation I noticed the setting winbind offline logon: This parameter is designed to control whether Winbind should allow to login with the pam_winbind module using Cached Credentials. If enabled, winbindd will store user credentials from successful logins encrypted in a local cache.. To me it looks like this solves the issue but can anyone else confirm it and/or point out if any additional values need to be set?

  Read the article

• Upgrading from php 5.3 to php 5.4 with Macport

  - by dr.stonyhills

  PHP5.4 has been available for sometime now and Macport recently caught up with the release of port php54 but the process of upgrading is not as clear as possible. Even worst for those who are new to maintaining multiple versions of PHP on the same machine. I am keen on trying out some of the new features in PHP5.4 like traits, new array form etc but falling back on to php5.3 for other compatibility stuff. So i sudo port install php5+ (all the variants, apache2 etc) Then i tell it what PHP port to use as default sudo port select --set php php54 Check what version of PHP is active in the terminal using php -v outputs php 5.4.3. But i seem to be having issues with choosing the right non cli version as in the version of the module run by apache etc is still php5.3.12. Do i have to change the reference to the libphp5 in apache httpd.conf? Any advice on the right workflow for switching between php version on macport greatly appreciated!

  Read the article

• How to set up Drupal Plugin Manager on MAMP in a secure way?

  - by Andrei

  Hi, I use MAMP PRO as global webserver. First of all, is it a good idea? Secondly, my objective is to run a Drupal website with as easy management as possible. Now I want to use Plugin Manager module to install additional modules and themes for my website. It wants to use ftp for that, and I know that if I open access to FTP port then IT-department guys will come to me and ask to shut it down. So I wonder if there is a way to allow Plugin Manager to install modules, having the port 21 closed somehow?

  Read the article

• What disk setup is needed / best practice for hypervisor-only servers?

  - by Luke404

  Planning to buy some servers to run an hypervisor (Citrix XenServer or VMware vSphere, still have to decide between the two) we'd like to boot off the local redundant SD card module offered by various vendors (eg. Dell, HP, etc...). The actual VMs will run from an existing iSCSI SAN (which, by the way, can't support booting the servers directly off the SAN). What are the reasons, if any, to choose completely diskless servers VS having some local storage? And what would be the guidelines to choose that local storage? (number of spindles, raid level, etc)

  Read the article

• win7: app crashing/hanging on "save as"-dialog

  - by Fuxi

  hi all, now this is really annoying - i'm having a global problem in win7: when using the system's "save as"-filedialog, the main app will just hang. the mouse-cursor is showing progress, the whole app is hanging and i need to terminate it manually. it's happening with every app! (notepad, word, graphics app). i'm assuming it's something with the system enumerating the harddisk-drivenames or something. any idea how to fix this? btw - when viewing the problem details - it's telling the module - it's msonsext.dll looks like some office thing to me. thanks

  Read the article

• Setting Up nginx Site Down That Responds Differently to Ajax?

  - by dave mankoff

  I am trying to set up an automatic site-down page for nginx. So far I have this: location / { try_files /sitedown.html @myapp; } location @myapp { ... } That works well enough: if sitedown.html is present, it serves that, otherwise it serves the app. What I'd like to do, however, is respond differently to Ajax requests so that they don't error out the javascript. I believe, using the rewrite module, that I can do something like if ($http_x_requested_with = XMLHttpRequest) { but it's unclear to me how to use this in order to do what I want. I'd like requests that come with that header to return a simple JSON response like "sitedown" with the appropriate json encoding header. Barring that, it would be nice to return a 503 response code that the javascript could react to.

  Read the article

• RJ45 female to male fault

  - by GeoPhoenix

  i have the following - common - problem, on one end of the cable, there are RJ45 males T586 A which are connected to a 8-port switcher, on the other end, there supposed to be RJ45 females _T586 A which in turn will allow another RJ45 male to be connected. the commonly used color scheme was followed on males (having the head down) blue white blue orange white green green white orange brown white brown the problem i believe is located on female end of cable, which i try multiple time to follow the numbers designated by the module, which is the list above in reverse, and as listed resulting in no signal transmission. tried the T586B (both ends) for device to device once, but no results. Which is the proper way of handling this wiring? There were also additional RJ45 females with the numbers 6-5-4-3, but 1 to 8 isn't supposed to be used for this?

  Read the article

• Apache - mod_pagespeed freezes my website

  - by Jonathan Rioux

  I have installed the mod_pagepseed module for Apache. I am using Debian so I downloaded the .deb file, and installed it successfully. I then configured some filters, and it worked like a charm for some minutes. Then after something like 10 minutes, my website no longer responded to the requests. When I was requesting for my website, it said "Waiting for www.blablabla.com" and I never got the page back from the server. I checked the processes running on my Debian box with top -d 0.5, and nothing eats up the CPU. To make my website responding to requests again, I must do a /etc/init.d/apache2 restart. And then it works again with mod_modspeed applying it's filters for a couple of minutes, and no more response again. How can I diagnose this issue? Is there some other configurations in the mod_pagespeed.conf file that I must set?

  Read the article

• how can i realize a video-wall on 3-9pc with vlc

  - by Luca

  hello! i have to create a videowall, from 3 to 9 monitor. every monitor as a pc. actually, i stream from a server 9 movies with different istances of VLC, but i could also play on every machine the relative video with a single player. there's no problem. the real problem is that i really dont know how to sync the videos on a LAN...unfortunately there is a NETSYNC module inside VLC wich is NOT working. here are some info about my setup: videowall from 3 to 9 monitor || from 3 to 9 pc, all with the same configuration || a gigabit router+switch for the "dedicated" LAN im really stuck in this situation, if anyone has an idea or just a completely different solution, please, share it with me! thanks a lot in advance! :)

  Read the article

• Squid and Webmin - the 'all' acl

  - by Genboy

  In older versions of versions of squid, you had to define an acl 'all'. acl all src 0.0.0.0/0.0.0.0 You use this for http_access allow all http_access deny all etc. In Squid 3.0 and above, the 'all' ACL is built-in, you cannot (& need not) define it. However, the webmin squid module doesn't seem to know this - when you try to add a rule using all, it doesn't show 'all' in it's list of ACLs. How does one get around this? I am using webmin 1.530 on Debian Lenny. Squid Version is 3.0.STABLE19-1~bpo50+1

  Read the article

• Hiera concatenated lookup from yaml

  - by Brian

  I am trying to configure the puppet-logstash module via Hiera. When I make the call to hiera('profiles::logstash::config'), the return value is a concatenated string. It tells me that it cannot convert a String into a hash. shipper.pp class profiles::logstash::shipper() { $shipper_config = hiera('profiles::logstash::config') notice("${shipper_config}") class { 'logstash': ensure => 'present', version => '1.4.1-1_bd507eb', status => 'enabled', } profiles::logstash::config { $shipper_config: } include logstash } hostname.yaml classes: - os::repo - profiles::logstash::shipper profiles::logstash::config: - {content: this is a test, order: 10} Output when used with notice(): order10contentthis is a test Did I order my YAML wrong?

  Read the article

• How can I protect files on my NGiNX server?

  - by Jean-Nicolas Boulay Desjardins

  I am trying to protect files on my server (multiple types), with NGiNX and PHP. Basically I want people to have to sign in to the website if they want to access those static files like images. DropBox does it very well. Where by they force you to sign in to access any static files you put on there server. I though about using NGiNX Perl Module. And I would write a perl script that would check the session to see if the user was sign in to give them access to a static file. I would prefer using PHP because all my code is running under PHP and I am not sure how to check a session created by PHP with PERL. So basically my question is: How can I protect static files of any types that would need the user to have sign in and have a valid session created with a PHP script?

  Read the article

• replace controller, add second controller, or use expander?

  - by longneck

  I have a Proliant DL380 G6 that I am re-purposing as a Hyper-V host for a new, off-site data center that will host our DR services. The server currently has a P410i controller with the 512MB BBWC module. The drives installed are SFF 6G 10K drives. I plan to add the HP 516914-B21 drive cage, which gives me 8 more SFF drives, bringing the total to 16. To get the additional 8 drives connected, I have one of three choices: Install a new controller that can support 16 drives. Install a second controller. Install a SAS expander, such as the HP 468406-B21 recommended by HP's spec sheet for my server. My question is: how do I know if I'm going hit a performance ceiling by putting 16 drives on the P410i or using the expander? And if I am, how do I select an appropriate controller? I'm not sure what specifications I should be looking at.

  Read the article

• Laptop Locking Up

  - by David

  I am having a very weird issue on a Lenovo W510 laptop. It will lock up randomly. I have had it lock up during post, during the boot-up of Linux, during login, and after the login. The following are tests that I have performed on the laptop. I ran memtest I took out the extra memory module. I swapped the HDD with another HDD that had Windows 7 on it. (It BSOD'd, and before anyone could possibly read the error line, it restarts.) I tried taking the battery out and booting with only the Power cord. The only other options I can think of the problem being are the motherboard or the PSU. If anyone has any advice, I appreciate it. If not, the HP guy will be here in a few days to fix it. I would just love to call them up and tell them that the service is no longer needed.

  Read the article

• Hiding "Syntax OK" from apache2ctl output

  - by Oscar Barrett

  I am checking whether a particular apache module is installed using apache2ctl -M. When listing the modules, apache runs a syntax check on the configuration files which prints out "Syntax OK" if everything is fine. However, this message doesn't seem to be coming from STDOUT or STDERR as it shows even if all output is redirected to /dev/null. i.e. $ sudo apache2ctl -M Loaded Modules: core_module (static) log_config_module (static) ... Syntax OK $ sudo apache2ctl -M >/dev/null Syntax OK How is this being outputted, and is it possible to hide?

  Read the article

• Error running Solr

  - by Jon H

  I'm trying to install Apache Solr for Plone, via collective.solr. I've followed the instructions above, and extended my buildout with: [buildout] extends = buildout.cfg https://github.com/Jarn/collective.solr/raw/master/buildout/solr.cfg [instance] eggs += collective.solr bin/buildout runs fine, however, when I try bin/solr-instance fg I get the following error: Traceback (most recent call last): File "bin/solr-instance", line 114, in <module> start(False) File "bin/solr-instance", line 43, in start stdout=logfp, stderr=logfp).pid File "/usr/lib/python2.6/subprocess.py", line 633, in __init__ errread, errwrite) File "/usr/lib/python2.6/subprocess.py", line 1139, in _execute_child raise child_exception OSError: [Errno 2] No such file or directory Graceful stop What am I missing / doing wrong?

  Read the article

• Puppet causes endless restarts of CUPS (how does one prevent this)

  - by Purfideas

  Hi! It makes sense, and is in fact suggested on this site, to have a critical file change trigger a service restart with puppet meta-parameters (such as notify or subscribe). For example: ## file definition for printers.conf file { "/etc/cups/printers.conf": [snip], source => "puppet:///module/etc/cups/printers.conf" } ## service definition for sshd service { 'cups': ensure => running, subscribe => File['/etc/cups/printers.conf'] } But in the case of CUPS, this triggers and endless loop of restarts; the logic works like this: Change puppetmaster's version of /etc/cups/printers.conf puppetmaster pushes new version to client, triggering cups restart cupsd restart insists on putting its own time stamp at the top of printers.conf, 'Written by cupsd...' This change will be seen as out of date, so after runinterval, we return to (1). Is there a way to suppress cupsd's need to time stamp the file? Or is there a puppet trick that could help here? Thanks!

  Read the article

• pymatplotlib without xserver

  - by vigilant

  Is it possible to use networkx or pymatplotlib without an xserver running? I keep getting the following error with their first example (of networkx): Traceback (most recent call last): File "test.py", line 17, in <module> nx.draw(G,pos,node_color='#A0CBE2',edge_color=colors,width=4,edge_cmap=plt.cm.Blues,with_labels=False) File "/usr/local/lib/python2.6/dist-packages/networkx-1.3-py2.6.egg/networkx/drawing/nx_pylab.py", line 124, in draw cf=pylab.gcf() File "/usr/lib/pymodules/python2.6/matplotlib/pyplot.py", line 276, in gcf return figure() File "/usr/lib/pymodules/python2.6/matplotlib/pyplot.py", line 254, in figure **kwargs) File "/usr/lib/pymodules/python2.6/matplotlib/backends/backend_tkagg.py", line 90, in new_figure_manager window = Tk.Tk() File "/usr/lib/python2.6/lib-tk/Tkinter.py", line 1646, in __init__ self.tk = _tkinter.create(screenName, baseName, className, interactive, wantobjects, useTk, sync, use) _tkinter.TclError: couldn't connect to display ""

  Read the article

• Powershell if statement not working - help!

  - by Dmart

  I have a batch file that takes a computer name as its argument and will install Java JRE on it remotely. Now, Im trying to run this Powershell script to repeatedly call the batch file and install Java on any system that it finds without the latest version. It seems to run error-free, but the statements inside the if code block never seem to run - even when the if conditional test evaluates to true. Can anyone look at this script and point out what I'm possibly missing? I'm using the Quest AD cmdlets, and BSOnPosh module. Thank you. get-qadcomputer -sizelimit 0 -name mypc* -searchroot 'OU=MyComputers,DC=MyDomain,DC=lcl'| test-host -property name |ForEach-Object -process { $targnm = $_.name $tststr=reg query "\\$targnm\HKLM\SOFTWARE\JavaSoft\Java Runtime Environment" /v Java6FamilyVersion if(-not ($tststr | select-string -SimpleMatch '1.6.0_20')) { $mssg="Updating to JRE 6u20 on $targnm" Out-Host $mssg Out-File -filepath c:\install_jre_log.txt -inputobject $mssg -Append cmd /c \\server\apps\java\installjreremote.cmd $targnm } else { $mssg ="JRE 6u20 found on $targnm" Out-Host $mssg Out-File -filepath c:\install_jre_log.txt -inputobject $mssg -Append } }

  Read the article

< Previous Page | 295 296 297 298 299 300 301 302 303 304 305 306  | Next Page >