Search Results

Search found 56140 results on 2246 pages for 'super computer'.

Page 303/2246 | < Previous Page | 299 300 301 302 303 304 305 306 307 308 309 310  | Next Page >

• Windows XP SP3 Keyboard stops working

  - by Kevin K

  Here's the strangest thing I have yet to see in 20+ yrs of computer repairs. My in-laws Windowsx XP SP3 has stopped recognizing keyboards. The keyboards work fine in the BIOS, during the boot select process to boot normally, etc. but once Windows comes up it will not recognize any USB keyboard. The USB mouse works fine, have tried different USB ports, different keyboards, etc. nothing works. I can log into the machine via VNC and use the remote keyboard just fine, but not connected locally. Tried a system restore, it says nothing changed. I am about to just re-install Windows at this point, except I am afraid it will happen again. I have googled for this and it is not unheard of, but I have not found any solution other than nuking it. Anyone have any ideas? I have re-installed the USB drivers for the M/B. Gone into devices and deleted them for a re-install, etc. Keyboard works off a Linux live boot CD, and in the BIOS setup so it is not a hardware issue, and I have tried a few keyboards all of which I know are good and work fine on other systems.

  Read the article

• CD and DVD burning very slow with LG DVD Burner

  - by Om Nom Nom

  I have an HP m7560in Desktop which came with an LG DVD burner. As far back as I can remember, it has been having problems in burning discs. It used to take about one and a half hour to burn 4 GB of data on a blank DVD-R. I am using Nero and ImgBurn and I usually select 8x speed for burning. I used to run XP earlier and now I run Windows 7 on it, but I face the problem on both. I have already checked that DMA mode is selected in the IDE controllers' properties. On XP, uninstalling the IDE controllers and DVD drive from the Device Manager, rebooting and letting it install the drivers again fixed the problem for a while, but after a couple reboots, the problem used to come back. On Windows 7, even doing that is not fixing the problem. In fact, in Windows 7, the burning process doesn't even begin. Imgburn gets stuck on the first stage (of writing Lead-In), and it never progresses until I turn off / reset the computer. I checked the disc info after this happened, and the disc still shows empty and ready to be burned on, so it's obvious that it didn't even touch the disc. I have already had the drive replaced once by HP, but it didn't fix the problem. Do you guys have any suggestions? (Note that Windows Updates doesn't give any newer driver for the controllers, or any other components for that matter).

  Read the article

• What is the best keyboard for typing speed (not layouts)

  - by Gapton

  So I am a programmer, and I like playing typing speed games. My typing speed is, for common English words, 85 to 90 wpm, max 95. I type on various devices, my laptop, desktop, office pc.... they all have slightly different keyboards. Being a curious programmer, I wonder what types of keyboard is used for the highest possible typing speed. Or let me phrase it in another way, what is the type of keyboards that people use in typing speed contest? Here is something I know that I feel like I can share: It must be a wired keyboard, I can feel the lag as I am typing this on my wireless keyboard, even if it is a slightly more expensive model which claims to have zero lag. I know people prefer a mechanical keyboard, for the hepatic feedback, however I have not tried one. It lasts longer and is noisy, it also does not have the problem of normal keyboards where you press many keys at a time the signals will get all jammed and the computer will only receive one or two keys. I personally prefer those "thin profile" keyboards. I type a lot, and 95 wpm put me in the top 5%, this is of course just on a gaming site. However when I type on the fat keyboards, my fingers have to travel a much longer distance before the keys actually click. This is where I find myself typing much faster with those thin profile keyboards found on my laptop. Because my fingers only hover on the keys and I only need to press a short distance, each stroke takes less force and light rapid strokes is what makes me type fast. When I type on a fat keyboard, I was forced to use heavy strokes, and this slows me down. There must be some people out there who are keyboard scientists, who actually do experiments and user tests with different setups. It would be interesting to understand more about the things we use everyday for not just work but a majority of our communications. P.S. this is about hardware and not about switching keyboard layouts to dvorak

  Read the article

• award phoenix bios not recognizing my sata hdd.

  - by josh

  What am I doing wrong? I have a custom built comp with a Fatal1ty AA8XE mobo. It has 4 SATA ports and one IDE port. When i first got it, I had a really hard time putting in more than one hard drive. Right now i have one 120gb IDE HDD on master and my DVD+-RW on slave connected to the one IDE spot on the mobo. I ripped a bunch of movies and filled up my HDD, so I got a WD 80gb SATA drive. I plugged it into SATA1 and hooked up the power, turned on comp, went into bios. The only thing in any option in any of the menues in this crazy lookin bios is a thing that says "SATA mode". i put it on IDE, set it so PATA is primary, SATA is secondary. booted up my comp, nothin. Not recognizing the SATA. I went back into the bios and checked it all again. I saw that it says SATA2 and SATA4 are the secondaries so i put it on SATA2, booted, nothing, same with SATA4, same with SATA3, all same as SATA1. Bios and wt os are not recognizing the drive as being there at all. I even downloaded and printed the almost 100 page manual for the mobo, read the entire thing, and still can't figure it out. I know there are a lot of people out there smarter than me when it comes to computers. So please, somebody, anybody, please tell me something that I'm not seeing. Some setting somewhere that I didn't configure right. There is something, obviously, but I can't find it. As far as i can tell, everything is set perfectly fine for my 120gb to be the master and the SATA to be the slave. I don't know what I'm doing wrong but I'm seriously about to throw this computer out the window. thankyou in advance to whoever attempts to help.

  Read the article

• Don't let the mouse wake up displays from standby

  - by progo

  I like to put my displays to powersave/standby mode when I leave the computer for a while. It would be ok if it weren't for oversensitive mouse. Sometimes the driver reads in some movement that's not visible to the naked eye (the cursor, that is) and it breaks the power save. It would wait for another 10 minutes before going back to its standby. My workaround is the following script bound to C-S-q: xlock -startCmd 'xset dpms 2 2 2' -endCmd 'xset dpms 600 1200 1300' -mode blank -echokeys -timeelapsed +usefirst By using xset I set the values to 2 seconds each before going to standby. It's not nice, anyway. Sometimes there are cool fortunes that I want to read before typing in the password. I could keep the cursor moving but it's cludgy. (By the way, xlock's option mousemotion doesn't help -- it just hides the cursor but the displays fire up nevertheless.) So the question: is there a way to make displays go standby and stay there until a keyboard key is pressed? I'm running gentoo and recent Xorg, but I hope the answer doesn't have to be distro-specific. Basically the answer can be as simple as how to enable/disable mouse within command line? It think that would do the job if DPMS doesn't know the idea.

  Read the article

• Editing a windows XP installation's registry without being able to log in.

  - by Alain

  I've got a windows XP installation that has a corrupt registry. A worm (which was removed) had hijacked the HKLM\Software\Microsoft\Windows NT\CurrentVersion\Winlogon entry (which should have a value of Userinit=C:\windows\system32\userinit.exe When the worm was removed, the corrupt entry was deleted entirely, and now the system automatically logs off immediately after attempting to log in. Regardless of the user and boot mode, no accounts can be logged in to. The only thing required to correct this behavior is to restore the registry key, but I cannot come up with any ways of editing the registry without logging in to an account. I tried remotely connecting to the registry but the required services aren't enabled on the machine. I tried booting on the same machine using the BartPE boot CD but I could not find any way of editing the registry on the C:\Windows installation - running regedit only modifies the X:\I386\ registry in memory. So, what can I use modify the registry of an un-login-able Windows XP instance so that I can log in again? Thanks guys. EDIT: The fix worked. The solution to the auto-logoff problem was, as hoped, to simply add the value mentioned above to the appropriate registry entry. This can be done using the BartPE Boot CD, as described in the accepted answer below, but I used the Offline NT Registry Editor software mentioned in another answer. The steps were: Boot from the NT Registry Editor CD Follow the directions until the appropriate boot sector is loaded. Instead of using one of the default options for modifying passwords or user accounts, type "software" to edit that hive. Type '9' to enter the command line based registry editor. Type "cd Microsoft" (enter) "cd Windows NT" (enter) "cd CurrentVersion" (enter) "cd Winlogon" (enter) Type "nv 1 Userinit" to create a new value under the Winlogon key Type "ev Userinit" to edit the new value, and when prompted, type "C:\windows\system32\userinit.exe" (enter) Type 'q' to quit the registry editor, and as you back out of the system, follow directions to write the hive back to disk. Restart your computer and log in - problem solved. (generic 'warning: back up your registry' disclaimer)

  Read the article

• Installing ubuntu 12.04, installs but does not boot after it asks me to remove the CD

  - by Randnum

  I'm Trying to install Ubuntu 12.04 on my computer. It had an old copy of Windows 7 on it I tried to reformat the hard drive for a fresh install of Ubuntu but I think I messed up the partitions in some way that prevents it from fully loading. I'm able to complete the install fine and use guided partitioning so it should be happy but when it gets about 90% through at the part that ejects the cd and restarts the system it fails. After ejecting the CD and restarting it just loads up the bios lenovo splash screen then purple then black. I can hear a sound from my speakers like some notification sound but there is no text on my screen. I've since gone back in under Rescue System to try and reconfigure the partitions hoping that it will fix it and i've tried several combinations. Currently it's SCST1 (0,0,0) (sda) - 500.1 GB ATA WDC WD5000AAkKX-0 #1 100.0 MB K biosgrub #2 494.1 GB B K ext4 / #3 5.9 GB F swap swap 8.2 kb FREE SPACE I'm not sure if I need to set the ext4 to contain the boot flag but if I don't include at least one partition with the boot flag enabled it complains saying that "The partition table format in use on your disks normally requires you to create a separate partition for boot loader code. This partitionshould be marked for use as an "EFI boot Partition" and should be at least 35 MB in size. Note that this is not hte same as a partition mounted on /boot" Like I said it seems to have installed all of the actual data from the CD it's just not properly booting for some reason

  Read the article

• Created new torrent but client unable to find seeds

  - by ehfeng

  I tried creating a new torrent, using uTorrent, following the directions from torrentfreak (http://torrentfreak.com/how-to-create-a-torrent/). I used a bunch of trackers (just in case any individual one was having troubles) and uTorrent shows it as "seeding" with 100% of the file. It shows: seeds 0(1), peers 0(0). http://exodus.desync.com/announce http://eztv.tracker.prq.to/announce http://open.tracker.thepiratebay.org/announce http://www.torrent-downloads.to:2710/announce http://denis.stalker.h3q.com:6969/announce udp://denis.stalker.h3q.com:6969/announce http://www.sumotracker.com/announce I've also attempted to remove the torrent and then re-add the torrent, pointing it to my already existing files, forcing uTorrent to recheck the files and then begin seeding. Yet when I share the .torrent file with my other computer and attempt to download, it is unable to find any peers or seeds. To confirm that both clients are working, I downloaded a torrent on both computers, using their respective clients, using torrents I found on isohunt. This tells me that there must be something wrong in how I'm creating my torrents. Any help is appreciated.

  Read the article

• Use synergy with Physical KVM

  - by Mr. Man

  I am using synergy on a Linux Mint computer as the server with a Mac as the client. I also have a physical KVM switch. The problem I have is that when ever I switch the physical KVM to my Mac, synergy stops working as in the keyboard and mouse don't work with the Mac. Thanks in advance! EDIT: here are some logs: From the Mint machine: INFO: synergys.cpp,1042: Synergy server 1.3.1 on Linux 2.6.31-14-generic #48-Ubuntu SMP Fri Oct 16 14:04:26 UTC 2009 i686 DEBUG: synergys.cpp,1051: opening configuration synergy.conf DEBUG: synergys.cpp,1062: configuration read successfully DEBUG: CXWindowsScreen.cpp,847: XOpenDisplay(:0.0) DEBUG: CXWindowsScreenSaver.cpp,339: xscreensaver window: 0x00000000 DEBUG: CXWindowsScreen.cpp,117: screen shape: 0,0 1024x768 DEBUG: CXWindowsScreen.cpp,118: window is 0x03800004 DEBUG: CScreen.cpp,38: opened display DEBUG: CXWindowsScreen.cpp,679: registered hotkey F12 (id=efc9 mask=0000) as id=1 NOTE: synergys.cpp,500: started server INFO: CServer.cpp,1141: screen ubuntu shape changed NOTE: CClientListener.cpp,127: accepted client connection DEBUG: CClientProxy1_0.cpp,404: received client marks-mac.local info shape=-1024,0 2304x800 NOTE: CServer.cpp,278: client mac has connected INFO: CServer.cpp,447: switch from ubuntu to mac at -1024,393 INFO: CScreen.cpp,116: leaving screen DEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG: CXWinavDEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDEBUG302)DEBUG: CXWindowsClipboard.cDEBUG: CXWindowsClipboard.cDE47DEBUG: CXWindowsClipboard.cDEBUG: CXWindowsrset=utf-8 (633), text/plain (462) DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555: added f DEBUG: CXWindCXWDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG:SerDEBUG: CXWindowsClipboard.cpp,555: ed DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555owsClDEBUG: CXWindowsClipboard.cpp,555: 1DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: getDEBUG: CXWindowsClipboard.cpp,555: added f DEBUG: CXW8_STDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555: added fD textDEBUG: CXWindowsClipboard.cpp,555: added fDEBU DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipinDEBUG: CXWindowsClipboard.cpp,555:oardDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindCXWDEBUG: CXWindowsClipboard.cpp,555: added fDEBUG:SerDEBUG: CXWindowsClipboard.cpp,555: ed DEBUG: CXWindowsClipboard.cpp,555: added fDEBUG: CXWindowsClipboard.cpp,555owsClDEBUG: CXWindowsClipboard.cpp,555: 1DEBUG: CXWindowsClipboard.cpp, s From the Mac: connecting to '192.168.3.5': 192.168.3.5:24800 connected to server entering screen leaving screen entering screen leaving screen stopped client

  Read the article

• How to configure Farsun USB barcode scanner to not auto-trigger

  - by David Grayson

  At my company we have several USB barcode scanners. I'm not sure exactly what model they are, but I think they are the FG9800 from Farsun because that's what they look like on the exterior. They came with a programming manual that is very similar to this document from the Farsun website. When I scan the "Output Firmware Version" barcode, my scanner types the following into the computer: Farsun V2.00 2011-01-01 Is it possible to configure these scanners so they only read barcodes in response to the trigger button being pressed? I don't want them to automatically read barcodes. Additionally, I want this setting to be remembered while the scanner is turned off. Since this scanner only has a USB port, the only way to configure it that I know of is to scan bar codes from the manual (or make your own). I have tried scanning the configuration bar codes for Single Scan (013300), Single Scan No Trigger (013301), and Laser/CCD Timeout - 5 Seconds (0134005) from this document. Sometimes (but not often) this puts the scanner in to the right mode, where it only scans when the button is pressed. Unfortunately, the scanner seems to always leave this mode when it is power cycled. I have also scanned the "Reset Configuration To Defaults" barcode (0B) many times. We have three different scanners like this and I have not been able to successfully configure any of them. If the things I want are not possible with these Farsun-based scanners, is there some other scanner we can use?

  Read the article

• How to disable 3rd party cookies in Chrome?

  - by David Nordvall

  I have both the "stop websites from storing local data" and the "block all third party cookies without exception" settings enabled in Chrome 12 (I'm not sure what the exact names of these settings are in english as I run Chrome with swedish localization). I do however have two problems. My first problem is that when I'm visiting one of my local news paper's site (and surely other), cookies from www.facebook.com is allowed for some reason. I suspect that the reason is that I have added an exception to the www.facebook.com domain but as the setting "block all third party cookies without exception" implies, that shouldn't matter. My second problem is that if I check what cookies are stored on my computer after browsing for a while, I have tons of cookies that are not on my white list. Primarily from ad services. My expectations from enabling the above mentioned settings was that only cookies that fulfill the two folling requirements would be accepted: the cookies must be from the domain in my address bar the cookies must be from a domain on my whitelist Apparently this isn't the case. The question is, have I completely misunderstood the settings or is this a bug? And, either way, is there a way to accomplish my desired behavior?

  Read the article

• Using Virtualbox Bridge Networking fails connection from Guest OS to Oracle XE running on Host

  - by Licheng

  I am trying to make a JDBC connection from a VirtualBox Ubuntu Guest OS to an Oracle XE database running o Host. However, the connection is refused. Here are the details of my environment: VirtualBox: 4.1.4 Host OS: Windows 7 Guest OS: Ubuntu server 11.4 Networking mode: Bridged network Oracle XE database running on Host Issue: WebLogic server runs on the Ubuntu virtualbox. It attempts to connect to an Oracle XE database running on the Host OS (windows 7) with listening port 1521. On the Guest OS (Ubuntu), I am able to ping the Host computer from the Guest OS. However, when I configured a JDBC data source on the WebLogic server on the Guest OS to connect to the Oracle XE, connection took a long time, and eventually I received an "IO Exception: The Network Adapter could not establish the connection". When I tried "telnet host-ip 1521", no connection was established. With Bridge networking, I can make bi-directional connections between the host and the guest OS (e.g. connection through ssh and ftp). Is there anything I missed in the setup of Bridge networking and the guest/host OS? Note that I was able to make the same connection within a normal networking environment (i.e. not using virtual box). I am not sure whether Bridge networking is a good option for the work described above. Should I use host-only networking mode? If so, any specific configurations I need to perform? I read through the Virtual box document on setting up the host-only network, however, it lacks of details. I followed the procedures described in the manual, and couldn't even connect to the host. Could some experts here enlighten me on this issue? Much appreciated. Licheng

  Read the article

• Linux error when resume from RAM

  - by TuxPotato

  The last two times that I have resumed my laptop from sleep, it has hung and given me this set of errors: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 hda_intel: azx_get_responce timeout, switching to single_cmd mode: last cmd=0x01170700 ata6: softreset failed (device not ready) ata4: softreset failed (device not ready) [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 The last two messages repeat two more times. The first time this happened, Linux's Magic SysRq worked and did a soft reboot, and after that everything was fine till it went to sleep again. It wakes up and gives me this. Here are the laptop stats: Toshiba Satellite L455D-S5976 AMD Sempron SI-42 Processor 2GB DDR2 RAM HD TruBrite Display ATI Radeon Graphics (integrated) Running Ubuntu 10.10 32 bit I'm not sure about the hard drive, but its a 250GB drive with one NTFS partition, two Hidden NTFS, one Linux Swap, and one Ext4. Can someone tell me whats wrong with my laptop? NOTE: This only happens when I close the screen. My computer doesn't go to sleep with the screen open.

  Read the article

• Installing SATA dvd burner on machine with no spare SATA ports/connectors

  - by Faheem Mitha

  Greetings. I have the following motherboard Tyan Thunder K8WE S2895A2NRF Motherboard - extended ATX - nForce Pro 2200/2050 - Socket 940 - UDMA133, Serial ATA-300 (RAID) - 2 x Gigabit Ethernet - FireWire - 6-1 channel audio This is part of a computer that was assembled in the winter of 2006/2007. The user manual says the following with regard to SATA Integrated SATAII Generation 1 Controllers (from NForce Professional 2200) Two integrated dual port SATA II controllers Four SATA connectors support up to four drives 3 Gb/s per direction per channel NvRAID v2.0 support Supports RAID 0, 1, 0+1 and JBOD. I just purchased a SATA DVD burner. Here is the page for the product http://www.amazon.ca/gp/product/B002QGDWLK/ The problem I am facing is that I already have 4 SATA drives installed. I don't want to remove any of them. However, I want the DVD burner above installed as well. The person I am consulting with here (Bombay, India) tells me that my four available SATA ports are filled, and that my only option is to install a SATA card into the one free PCI slot on the motherboard. However, he says that with this setup I will not be able to boot from the DVD drive. Are these statements correct, and what are my other options if any? Even it the statements in the last para are true, I suppose I could use one of the motherboard connectors/ports there are currently being used with the hard drives with the DVD drive, and use the "add-on" connector with one of the hard drives. Not all the 4 hard drives need to be bootable. BTW, despite having read through http://en.wikipedia.org/wiki/Serial_ATA#Cables.2C_connectors.2C_and_ports I am fuzzy on the differences between connectors, cables and ports. Thanks in advance.

  Read the article

• What's hogging my CPU?

  - by endolith

  Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. I try killing lots of things, but it continues at 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, that normally only hits 100% CPU when I'm doing something that requires it (like loading 32 Firefox tabs) after which it goes back to a normal idle level. It's not a new install or anything. It shouldn't be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing any process I saw active again, and killing vino-server finally fixed the problem, even though it never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). How did it manage to use 100% CPU while top only showed it as 5% or so? How do I identify the culprit in the future? Looks like I'm not the only one: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

  Read the article

• Upgrading Visio 2000 to Visio 2007

  - by dirtside

  I have Microsoft Visio 2000 SR 1, and recently purchased Microsoft Office Visio Standard 2007 with the understanding (supported by the product info and some other research) that I'd be able to upgrade. However, when I install 2007, it tells me it can't find a previous install of Visio, but... it's right there! Here's the exact message: "Setup can't find a version of Microsoft Office on your computer. If Office is installed on a disk or network share, click the browse button to select the appropriate disk or share... (etc.)" No matter which directory or drive I pick (various Office installs, the old Visio install, various subdirectories) it gives the following message: "The path you have chosen does not point at a qualifying upgradeable product. Click 'Retry' to try again or 'Cancel' to quit setup." Any ideas? This is a legit copy of Visio 2007 (purchased from Amazon) and the copy of Visio 2000 is legit as well. I'm not sure what exactly the installer is looking for that it would consider a "qualifying upgradeable product". A specific file?

  Read the article

• How To Fix Samba File Permission Issues in Mac OSX

  - by user1867768

  I've had this problem for a long time, here is the basics of it... I use a mixed environment of Windows 7/8 computers with Mac OSX Lion/Mountain Lion. Whenever a Windows computer creates a file on a SMB share on the Mac it no longer has group permissions, only the person who created or updated it can access it. My solution has been to go onto the Mac system and reset permissions for the entire directory structure then everyone can see it again. About the only thing on this that I can find was for OSX pre Snow Leopard that mentioned editing the SMB.CONF file to fix their particular problem (similar to mine, http://www.gladsheim.com/blog/2009/09/19/osx-leopard-and-samba-permissions/). The problem is that now Lion and Mountion Lion no longer have an SMB.CONF file (another web search pointed to the com.apple.smbd.plist (http://kidsreturn.org/?s=smb.conf) but it's an XML file now and I'm not clear on what should be done to THAT to fix the problem. So, short of me writing an Applescript to run every hour to fix permissions, does anyone know a solution to this very frustrating problem? Thank you in advance for any advice or solutions you can offer!

  Read the article

• Browsing Playstation 3 from Ubuntu Box

  - by zfranciscus

  Hi, My Goal here is to be able to transfer files from my Ubuntu 10.04 box to my PS3 over a wireless network. My PS3 and my Ubuntu Box is on the same home network. These are some stuff that I tried: I can't see my PS 3 from 'Places ? Network' nor other computer that is running on windows. I am still puzzled by this fact. I have not tried ping-ing my PS3. I'll try that later today and post the result in the forum I install PS3MediaServer (http://code.google.com/p/ps3mediaserver/). Someone in the PS3 chat forum (http://www.ps3chat.com/playstation-3...lp-please.html) claims that it will enable your ubuntu box to browse PS3. So I downloaded PS3MediaServer, and ran the software. The status tab keep showing "Waiting ...". It seems that PS3MediaServer can't find my PS3. Some how I feel that 1 and 2 are related somehow.Perhaps that there is something wrong with my Ubuntu network settings that is preventing my ubuntu box from looking up other device on the network. I can go to the Internet fine, but I can't see other device on my network. Does anyone have any experience in this area. I would like to hear your experience and perhaps some solution. Any kind of hints or help will be greatly appreciated. Cheers

  Read the article

• Ripping a home video VCD on Linux or Windows with VLC or otherwise

  - by user259774

  I have a VCD with 22 minutes of video on it. I would like to retain this footage and throw away the VCD. I can play the whole thing with VLC ("open disc - vcd - /dev/sr0 - play"): all 22 minutes of the main track. I don't believe there's any other content aside from the main track. I can seek to anywhere I want to within the 22 minute track. If I mount /dev/sr0 /media/vcd and then try to copy the only file from the MPEGAV folder, I get an I/O error, with an empty destination file. VLC has a "convert" option in addition to "play". When I use this I actually get a good OGG file back, after it runs through the video in painful real-time. I guess it dubs it frame-by-frame. But the file is only 10 minutes long, leaving 12 minutes off of the track. Handbrake doesn't detect it's track titles, unfortunately. I don't know if I should start getting involved with GNU ddrescue or if it's because VCDs somehow encode their data sectors differently. Anyway, I'm in way over my head and if anyone knows how I could get that video track off the thing, feel free to share! Edit: I should note that I also have access to a Windows computer

  Read the article

• Setting up a PC for the Kids

  - by Martin Clarke

  I recently finished building a new PC from scratch; and then I decided to treat myself to a new widescreen monitor. I'm left with a bit of a conundrum with what to do with my old box. I'm considering a few options such as a file server, putting Linux on it, putting it elsewhere in the house or giving it to a member of the family and so on. But to be honest, I don't really think it would get much use. I've started thinking about putting together something for my kids. The oldest is coming up on 4 in a couple of months and he's used my PC and Macbook (supervised!) before for playing jigzaw puzzles, babysmash and so forth. He's also uses the computer at his nursery (Kindergarden for North Americans!). So, its got me thinking about setting something up for him (bonus for his brother who is 2). I was wondering what others had done when trying to put together something for their kids? Some points for consideration: Operating System? Software? Anti-virus Internet (probably blocking?) Hardware (I've seen some keyboards designed with kids in mind)

  Read the article

• Can't view other computers on Network

  - by Darkart

  Systems: My Machine: Windows 7 Ultimate connected through ethernet into router Her Machine--Other Machine: Windows 7 Ultimate connected through wireless Router:F5D8236-4 N Wireless Router Version 1 Firmware: 2.01.03 (Apr 28 2009) ISP: Comcast Problem: I can not view the "Other Machine" on the network at all. I opened command prompt and ran net view and saw the pc name. I tried pinging the pc and it times out. Went inside the router and tried viewing the computer on the DHCP list and it can not be seen. I restored the router back to default settings and firmware and completely reset the modem and router, and created home group. I went to the other machine to configure home group settings and made sure that both PC's had identical settings. She was able to see my machine but I could not see hers. I restarted both machines and now we cant see each other at all. Also her PC ("Other Machine") had exclamation mark in the wireless icon but was connected just fine. There is no firewalls on currently or anti-virus enabled, and still can not see each other. Right now I am checking for updated drivers for the wireless card, but my question is could it be the router or something hardware related? I have went through all the settings in the Home group and visited most FAQ's and still no luck. Also as it stands I can not view her machine inside the router DHCP Client List :(

  Read the article

• Networking "chokes" on Windows 7 64 bit

  - by Rohit Nair

  I've been having this problem for some months now, and I have been unable to figure out a solution, or even the cause. At random points throughout the day, my internet connectivity "freezes". I don't get disconnected from my local wireless network. My router doesn't get disconnected from the world. However, for some reason, my computer stops receiving packets. If I'm playing an MMO ( World of Warcraft, in this case, but it has happened with Eve Online as well ) all activity just freezes. If I try to browse, Opera, Firefox and IE all stall at "Waiting for google.com..." or whatever the hostname may be. Inspection with a packet sniffer seems to reveal that there are no incoming packets. Here's the interesting part. Disconnecting from my wireless network and reconnecting fixes the issue. Obviously this led me to conclude that it was a problem with my router or wireless card. However, I have tweaked all the settings on my router that I could think of, including things like QoS, AP Isolation, etc. with no change. My wireless card doesn't really have that many options, and I have uninstalled and reinstalled drivers a few times without any change. Windows Firewall on/off doesn't make a difference. Anyone have any suggestions for debugging this? It's becoming an annoyance.

  Read the article

• Why can I not access the internet when Windows 7 finds no issue with the ethernet connection and the network can see my device?

  - by WannabeCoder

  So I just moved from a house to an apartment. In the house and the apartment I had Uverse set up - and in both I had my desktop connected via a ~40 foot long cat5 cable. However, upon moving to the apartment I found that my ethernet connection no longer provides internet. This would seem like a mundane problem if not for: The router can see the computer on the network Windows 7 (the desktop's OS) detects no problems with the ethernet connection. Connections over the internet (i.e. browser windows, Pandora, etc.) do not immediately fail. Instead they load for 2 minutes and then finally give up. Devices connected over the Wifi (PS4, Laptop) access the internet just fine While removing the cat5 cable from my house, I accidentally damaged the locking tab but managed to bend it back into the appropriate position. I would suspect that a bad cat5 cable might be to blame if not for the above issues (thought I've heard bad cat5 cables cause the most nonsensical problems) and the fact that I tested the cat5 cable by having it share internet between my laptop (working internet) to my desktop and it functioned just fine and provided the desktop with internet. My ipconfig /all successfully finds a default gateway, DHCP server, and DNS server. What could possibly be causing the problem?

  Read the article

• Migrating Windows XP BOOT.INI Settings to Windows 7 Boot-loader

  - by Synetech inc.

  Hi, Two months ago my motherboard died, so I bought a used computer that came with Windows 7. I have since installed my old hard-drive, which had Windows XP on it, in this system. What I am trying to do now is to figure out a way to migrate the settings from XP's BOOT.INI into 7's boot-loader. Below is the BOOT.INI I used in XP (I have reduced the strings and updated the disks to point to the new location of the old HD. Oh and I am not clear on the drive letters. In XP, I could boot the recovery console or MS-DOS from a file in C:\ that contains the boot-sector. I am not sure what drive letter it would be called now—I had to manually change all the drive letters of the old partitions in Windows 7 because it auto-assigned them all wrong/differently). [boot loader] timeout=10 default=multi(0)disk(0)rdisk(1)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP" /fastdetect multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP (Safe)" /safeboot:network /sos /bootlog /noguiboot C:\CMDCONS\BOOTSECT.DAT="Recovery Console" /cmdcons C:\BOOTSECT.DOS="MS-DOS 7.10" /win95 I have looked around, and have only been able to find some bcdedit commands to add XP to the boot-loader, but none that include information on setting safe-mode for it (or changing any of the XP load options for that matter). Not surprisingly I suppose, I have not found anything on adding the XP recovery console or DOS to the Windows 7 boot-loader. (Yes, I tried EasyBCD, but that did not help; it had no options for XP, and the best I managed was to get a choice of booting 7 or normal-mode XP—choosing XP didn't even give the old XP boot menu.) Can anyone please tell me how to export the entries in XP's boot.ini to 7's boot-loader so that on boot, I can choose to load the following: Windows 7 Windows 7 (Safe-mode) (Windows 7 (The Win7 counterpart of the Recovery Console)) Windows XP Windows XP (Safe-mode) Windows XP (Recovery Console) MS-DOS 7.10

  Read the article

• Linksys WAP54G v3.1 no access, power and link LED solid

  - by user142113

  I'm managing the Network of a small enterprise. A Linksys WAP54G v3.1 used to provide the WiFi network. I was called, because the device did not provide a WiFi network anymore. I first of all tried to ping the device via LAN, but there was no reaction. I've frequently reconnected the AP to the mains and always the POWER and the LINK LED keep solid, even if no network cable is connected. What I've done yet: Reset as documented: Pressed the RESET button for 10 seconds. After that I have tried to access the AP with a direct cable connection to my computer, that I've set to a static ip of 192.168.1.240, but i got no ping response on the default IP 192.168.1.245. Furthermore ipconfig reports "media disconnected". More complex reset method as described here http://bruceshankle.blogspot.de/2005/12/how-to-reset-linksys-wap54g.html as well had no effect. also tried to ping 192.168.1.1 without success Tried this method: http://www.daniweb.com/hardware-and-software/networking/threads/142437/linksys-wireless-access-point-problem#post680245 but there was no ping response when powering up. As well the tftp transfer timed out Finally tried to short pin 15 and 16 of the flash chip on the bottom side of the AP mainboard while booting to provoke a Checksum error. This should lead to the possibility to upload a firmware with tftp, as the AP stops booting and waits for a tftp connection on 192.168.1.1. But I've had no success. As well i've put pin 15 and 16 to ground while booting, also without an effect. After all that I still can't ping the AP, ipconfig still tells me "media disconnected". The POWER and LINK LED are solid. I would appreciate your answers

  Read the article

< Previous Page | 299 300 301 302 303 304 305 306 307 308 309 310  | Next Page >