Search Results

Search found 10515 results on 421 pages for 'automatically'.

Page 316/421 | < Previous Page | 312 313 314 315 316 317 318 319 320 321 322 323  | Next Page >

• Web Application Publishing on Citrix with Restricted Access

  - by Kanini

  We have a Citrix setup enabling users to access our applications from home. Basically, they login to our site using the Windows Authentication. Once, the are successfully logged in, they see the following icons Desktop - Full Screen (which provides them the Desktop as they would see when the login in our office) We now have a requirement where we would like to publish a web application, hxxp://ourlibrary on Citrix with the following security requirement. (this application is already accessible if the users launch the desktop and launch IE within it and navigate to it) The requirement is this - When the are successfully authenticated to our site, they should be able to see The Internet Explorer icon only, NOT the Dekstop - Full Screen icon. On clicking on the icon, Internet Explorer should open up and should automatically navigate to hxxp://ourlibrary They should not be able to access any other URL, such as Google, Hotmail etc., They should not be able to go FileOpen and Browse They should not be able to do FileSave and Browse In effect, they should be able to view the site and that should be it. Any ideas on how to accomplish the security feature? We have already published the application.

  Read the article

• Ubuntu second static IP, ifconfig, /etc/network/interfaces

  - by Schmoove

  I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

  Read the article

• systemd: enabling cherokee service as a `unit file`

  - by Calvin Cheng

  So I am learning how to use systemd to initialize my services automatically on server reboot. So of course, I first make sure I have systemd and some optional systemd related packages installed. pacman -S systemd initscripts-systemd Installation seems to go well and checking, I can see that systemd and its dependency libsystemd are installed. And the optional package initscripts-systemd is also installed:- [root@li280-195 ~]# pacman -Ss systemd extra/libsystemd 44-5 [installed] systemd client libraries extra/systemd 44-5 [installed] system and service manager extra/systemd-sysvcompat 2-2 sysvinit compat symlinks for systemd community/initscripts-systemd 20120412-1 [installed] Arch specific systemd initialization/bootup scripts for systemd community/systemd-arch-units 20120412-2 Arch specific Systemd unit files Next, I ensure that systemd is loaded up when my server reboots, via grub in grub's /boot/grub/menu.lst file like this:- kernel /boot/vmlinuz root=/dev/xvda ro init=/bin/systemd Rebooting my server to check, all loads up well and I can check that systemd is operational via:- systemctl list-unit-files However, I don't see my cherokee initialization script (which is simply created at /etc/rc.d/cherokee when I installed cherokee earlier via pacman -S cherokee) being listed as one of my unit files. So the question is, how do I do that? How do I put my cherokee initialization script under systemd's control?

  Read the article

• pdo_mysql installation

  - by Arsenal

  Hello, On my server I'm trying to instal PHP Projekt (6). This requires pdo_mysql however. I thought this installation of pdo_mysql would be rather straightforward... I tried using pecl (pecl install pdo_mysql) after installing devel etc, but this came up with a permission denied error. I solved this by using directories that were accessible. It then came up with a cant run C compiled programs however. It also says to check config.log for more details but ironically config.log is automatically removed if the installation process fails... When I try to compile and output a "hello world".c however, it works perfectly. I then tried to download the pdo_mysql stuff and install in myself (using configure and make install). This seemed to do the job, but when I restarted my apache ... no sign of pdo_mysql anywhere even though I adjusted my php.ini file I have read somewhere that you need to recompile PHP with the option pdo_mysql enabled. But how does one do that (I'm using CentOS4). And isn't there any other way than that??? Thanks!

  Read the article

• hosts.deny not blocking ip addresses

  - by Jamie

  I have the following in my /etc/hosts.deny file # # hosts.deny This file describes the names of the hosts which are # *not* allowed to use the local INET services, as decided # by the '/usr/sbin/tcpd' server. # # The portmap line is redundant, but it is left to remind you that # the new secure portmap uses hosts.deny and hosts.allow. In particular # you should know that NFS uses portmap! ALL:ALL and this in /etc/hosts.allow # # hosts.allow This file describes the names of the hosts which are # allowed to use the local INET services, as decided # by the '/usr/sbin/tcpd' server. # ALL:xx.xx.xx.xx , xx.xx.xxx.xx , xx.xx.xxx.xxx , xx.x.xxx.xxx , xx.xxx.xxx.xxx but i am still getting lots of these emails: Time: Thu Feb 10 13:39:55 2011 +0000 IP: 202.119.208.220 (CN/China/-) Failures: 5 (sshd) Interval: 300 seconds Blocked: Permanent Block Log entries: Feb 10 13:39:52 ds-103 sshd[12566]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12567]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12568]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12571]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:53 ds-103 sshd[12575]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root whats worse is csf is trying to auto block these ip's when the attempt to get in but although it does put ip's in the csf.deny file they do not get blocked either So i am trying to block all ip's with /etc/hosts.deny and allow only the ip's i use with /etc/hosts.allow but so far it doesn't seem to work. right now i'm having to manually block each one with iptables, I would rather it automatically block the hackers in case I was away from a pc or asleep

  Read the article

• Is there an SSL equivelent to an ssh agent?

  - by Matthew J Morrison

  Here is my situation: There are a number of developers who all need to have access to be able to install ruby gems and python eggs from a remote source. Currently, we have a server inside our firewall that hosts the gems and eggs. We now want the ability to be able to install things hosted on that server outside of our firewall. Since some of the gems and eggs that we host are proprietary I would like to somewhat lock access to that machine down, as unobtrusively as possible to the developers. My first thought was using something like ssh keys. So, I spent some time looking at SSL mutual authentication. I was able to get everything set up and working correctly, testing with curl, but the unfortunate thing was that I had to pass extra arguments to curl so it knows about the certificate, key and certificate authority. I was wondering if there is anything like the ssh agent that I can set up to provide that information automatically so that I can push the certificates and keys to the developer's machines so the developers don't have to log in or provide keys each time they try to install something. Another thing that I want to avoid is having to modify the 'gem' command and the 'pip' command to provide keys when they make the http connection. Any other suggestions that may solve this problem (not related to ssl mutual auth) are also welcome. EDIT: I've been continuing to research this and I came across stunnel. I think this may be what I'm looking for, any feedback regarding stunnel would also be great!

  Read the article

• Prevent Exchange Server from advertising itself on domain

  - by Justin Shin

  I'm in the middle of setting up an Exchange 2010 Server. Currently, we use a SaaS provider for Exchange 2007 services. Some (but not all) of my users have been reporting that they are receiving Outlook/Exchange login prompts to login to the new Exchange server. This is happening without any intervention on the client's machines. The Exchange server is a member of the domain and connects to the domain site remotely through a site-to-site VPN. What can I do to prevent these login prompts from appearing? Will shutting down the new server until it is time to switch resolve these issues? A little more info: I found that on one of the client computers, all of the settings for Outlook over HTTP had been changed (automatically) from webmail.provider.com to mail.company.com (the latter being the new server). This happened when I enabled Outlook Anywhere access on Exchange 2010. I changed the client's settings back, and everything was groovy. But, when I disabled Outlook Anywhere again, the logon prompt came back.

  Read the article

• OpenVZ Can't initialize containers after install

  - by Tonino Jankov

  I have installed OpenVZ on centos 6 on a dedicated server. I followed quick installation guide on openvz wiki. After installing thru yum, I don't know why, but grub.conf wasn't automatically updated to accomodate new kernel, so I had to do it manually. I edited grub.conf, added openvz kernel and rebooted - it went fine. Server went up into openvz kernel and it worked, it started openvz service byitself. But after I created a container, added IP to it and attempted to start it, I couldn't. Here is the output from the shell: [root@cloud2 ~]# vzctl start 86 Starting container ... Container is mounted Container start failed (try to check kernel messages, e.g. "dmesg | tail") Container is unmounted [root@cloud2 ~]# dmesg | tail [ 1973.401596] CT: 86: failed to start with err=-105 [ 2107.113850] Failed to initialize the ICMP6 control socket (err -105). [ 2107.155523] CT: 86: stopped [ 2107.155543] CT: 86: failed to start with err=-105 [ 6348.282184] Failed to initialize the ICMP6 control socket (err -105). [ 6348.330348] CT: 86: stopped [ 6348.330361] CT: 86: failed to start with err=-105 [45184.024002] Failed to initialize the ICMP6 control socket (err -105). [45184.072086] CT: 86: stopped [45184.072099] CT: 86: failed to start with err=-105 [root@cloud2 ~]# I don't know what is wrong. I tried different templates, debian 6, centos 6, i386, amd64, but the issue is the same. What is the problem?

  Read the article

• Hiera datatypes wont load in Puppet

  - by Cole Shores

  I have spent a couple of days on this, followed the instructions on http://downloads.puppetlabs.com/docs/puppetmanual.pdf and even the Puppet Training Advanced Puppet manual. When I run a test against it, the results always come back as 'nil' and Im not sure why. I am running Puppet 3.6.1 Community Edition, with Hiera 1.2.1 on SLES 11. My puppet.conf file at /etc/puppet/puppet.conf consists of: [main] # The Puppet log directory. # The default value is '$vardir/log'. logdir = /var/log/puppet # Where Puppet PID files are kept. # The default value is '$vardir/run'. rundir = /var/run/puppet # Where SSL certificates are kept. # The default value is '$confdir/ssl'. ssldir = $vardir/ssl certificate_revocation = false [master] hiera_config=/etc/puppet/hiera.yaml reporturl = http://puppet2.vvmedia.com/reports/upload ssl_client_header = SSL_CLIENT_S_DN ssl_client_verify_header = SSL_CLIENT_VERIFY # certname = dev-puppetmaster2.vvmedia.com # ca_name = 'dev-puppetmaster2.vvmedia.com' # facts_terminus = rest # inventory_server = localhost # ca = false [agent] # The file in which puppetd stores a list of the classes # associated with the retrieved configuratiion. Can be loaded in # the separate ``puppet`` executable using the ``--loadclasses`` # option. # The default value is '$confdir/classes.txt'. classfile = $vardir/classes.txt # Where puppetd caches the local configuration. An # extension indicating the cache format is added automatically. # The default value is '$confdir/localconfig'. localconfig = $vardir/localconfig my /etc/puppet/hiera.yaml consists of: :backends: yaml :yaml: :datadir: /etc/puppet/hieradata :hierarchy: - common - database I have a directory created in /etc/puppet/hieradata and within it contains: /etc/puppet/hieradata/common.yaml :nameserver: ["dnsserverfoo1", "dnsserverfoo2"] :smtp_server: relay.internalfoo.com :syslog_server: syslogfoo.com :logstash_shipper: logstashfoo.com :syslog_backup_nfs: nfsfoo:/vol/logs :auth_method: ldap :manage_root: true and /etc/puppet/hieradata/database.yaml :enable_graphital: true :mysql_server_package: MySQL-server :mysql_client_package: MySQL-client :allowed_groups_login: extranet_users does anyone have any idea what could be causing Hiera to not load the requested values? I have tried even restarting the Master. Thanks in advance, Cole

  Read the article

• Troubleshooting a Windows 7 PC that wouldn't sleep

  - by NPE

  I have a new Windows 7 PC that wouldn't sleep (not just automatically, but also when specifically told to). The screen goes black momentarily, but within two seconds the machine comes back as if nothing has happened. I tried powercfg energy. This produces some errors quoted at the bottom of this post, plus some warnings about timer resolution. There are no USB devices connected other than wireless keyboard + mouse (Logitech MK250); I tried unplugging them to no effect. The motherboard is Asus P7P55D-E. powercfg lastwake says "Wake History Count - 0", which I take to mean that it never actually went to sleep. I dual boot into Ubuntu, and was having exactly the same problem on the Linux side. That turned out to do with USB 3.0, which I've now disabled in the BIOS. This has solved the problem on the Ubuntu side of things, but made no difference to Windows 7. Any suggestions? Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name Generic USB Hub Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_8087&PID_0020 Port Path 1 USB Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name USB Root Hub Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_8086&PID_3B34 Port Path USB Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name USB Composite Device Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_046D&PID_C52E Port Path 1,8

  Read the article

• Persistent routes for DD-WRT PPTP VPN client

  - by Tim Kemp

  My home network in the USA is behind a Buffalo router (G300NH) running their version of DD-WRT. I use the built-in PPTP VPN client to connect to a VPN provider in the UK. I route certain traffic over the VPN (so it has a UK source address, for various entirely legal reasons) which I achieved by following the instructions in the DD-WRT docs and my VPN provider's own instructions. I placed two commands like this in the firewall script: route add -net xxx.xxx.0.0 netmask 255.255.0.0 dev ppp0 route add -net yyy.yyy.0.0 netmask 255.255.0.0 dev ppp0 I didn't put any of the iptables rules in since it my setup doesn't seem to need them. It works like a charm. Traffic to the xxx subnets goes over the VPN, everything else goes out over my ISPs own pipes. The problem comes when the VPN drops, which it does occasionally. DD-WRT does a fine job of reconnecting it automatically, but the routes are trashed every time that happens. How do I automate the process of re-establishing my routes? I thought about static routes, but the IP address of the VPN connection is dynamically assigned (which is why I'm using dev ppp0). Many thanks, Tim

  Read the article

• Cannot find network path for computer in workgroup of home Windows XP PCs

  - by John Galt

  VMWare Workstation 6.5 is running as an app on a Windows Vista 64bit PC host. Thanks to Workstation we have 2 guest machines running: TerriVM and MattVM (both of these run Windows XP SP2). We are attempting to get virtual networking configured so we can access the files of both of these VM guest systems from other real PCs connected to this home network. We think we are close but we can't quite get it right... Here is what we've done so far: * On VM Workstation, we set "Host Virtual Network Mapping" to use VMnet0 with the setting "Bridge to an automatically chosen adapter". * On each VM guest (i.e. using Windows explorer on XP), we rightmouse on the C disk, click "Sharing" tab, set shareName to "C_Disk" and check both boxes labeled "Share this folder on the network" and "Allow network users to change my files". Symptoms: On "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \TerriVM\C_Disk and assign drive letter T. We see all the folders on this shared drive and can open files on them. So that is good. On same "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \MattVM\C_Disk and assign drive letter M. We get a message box "_The network path \mattvm\C_Disk could not be found_". Alternatively, we type just \mattvm\ into the Folder box and click "Browse" and get a dialog box where we drill down from "Entire Network" to "Microsoft Windows Network" to "Workgroup" where both TerriVM and MattVM are listed as computers on the network. Clicking the + sign next to MattVM gives an hourglass and never enables the OK button and I have to cancel. In summary, I think we've attempted to share both of these virtual machines using the same techniques and connect to them in similar fashion, but one connects properly and the other machine can be seen but no shared resources on it can be accessed. Can anyone suggest something possibly overlooked or something to try? Thanks so much in advance.

  Read the article

• What could cause TFTP reloaded Cisco `running-config` on 871 to fail?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I went through the basic steps to reconfig the router. I looked to see if I could just reset the router. Nope. I tested the 871's flash memory with fsck to see if there was hardware failure. Nope. Then I rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config? Or on Vista to validate the config file itself before I transfer it? Or, is this there a common TFTP issue? UPDATE. I missed the instruction from Cisco's TFTP page to delete aaa lines from the config (although a video from a SuperUser user didn't make this point in his most excellent demo). There were several lines of this sort, I deleted them and uploaded again. However, they're back. I assume they're added automatically? [nope, see answer] UPDATE 2. The reload of previous settings was successful, but this error remains. I don't even know now if it was there before or not. It seems irrelevant to the question.

  Read the article

• Vista laptop 1 connects to network but Vista laptop 2 doesn't

  - by Jaips

  (Sorry if this is a dulipcate. I did a hunt but couldn't find matching question) We recently got a new router for our network (thomson TG585v8). It was already pre-configured by the ISP and was easy to setup. Both Vista laptops in this home network connected without trouble as well a iPod touch, all via wifi. In the last two days one of the laptops has been unable to connect cleanly to the network (connects as unidentified network). The other laptop, and iPod have not had any issues. I can't think of anything that has changed to make this happen now. I have rebooted the laptop and the router. I have updated the laptop wireless driver I have checked the laptop is set to automatically get IP I have logged into the router which correctly identifies all three wireless devices. The problem laptop connects via LAN without issue. Some things that may or may not matter: The problem laptop also sometimes uses a 3G dongle Both laptops use Windows Live Mesh to sync folders Laptop is usually set to go to sleep NB: it seems this is an intermittent issue, after an hour (since i noticed it) it seems to have fixed itself. Would love ideas though to solve this problem for good.

  Read the article

• 403.4 won't redirect in IE7

  - by Jeremy Morgan

  I have a secured folder that requires SSL. I have set it up in IIS(6) to require SSL. We don't want the visitors to be greeted with the "must be secure connection" error, so I have modified the 403.4 error page to contain the following: function redirectToHttps() { var httpURL = window.location.hostname+window.location.pathname; var httpsURL = "https://" + httpURL ; window.location = httpsURL ; } redirectToHttps(); And this solution works great for every browser, but IE7. On any other browser, if you type in http://www.mysite.com/securedfolder it will automatically redirect you to https://www.mysite.com/securedfolder with no message or anything (the intended action). But in Internet Explorer 7 ONLY it will bring up a page that says The website declined to show this webpage Most Likely Causes: This website requires you to log in This is something we don't want of course. I have verified that javascript is enabled, and the security settings have no effect, even when I set them to the lowest level I get the same error. I'm wondering, has anyone else seen this before?

  Read the article

• How to add Sharepoint Powershell to Console2

  - by BGM

  Salvete! I want to add the Powershell Console for Sharepoint to the tablist in Console2. I already have plain Powershell, but I want the Sharepoint Powershell snapin added automatically. If I look at the properties of the Sharepoint Powershell Console shortcut, I see this: C:\Windows\System32\WindowsPowerShell\v1.0\PowerShell.exe -NoExit " & ' C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\CONFIG\POWERSHELL\Registration\\sharepoint.ps1 ' " but that doesn't work in Console2, so I tried this, which doesn't work either: C:\WINDOWS\system32\windowspowershell\v1.0\powershell.exe -PSConsoleFile "C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\CONFIG\POWERSHELL\Registration\psconsole.psc1" -NoExit " & ' C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\CONFIG\POWERSHELL\Registration\\sharepoint.ps1 ' " Whenever I try, it will load Powershell, but not the Sharepoint Console. I get this: Add-PSSnapin : The Windows PowerShell snap-in 'Microsoft.SharePoint.PowerShell' is not installed on this machine. At C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\CONFIG\POWERSHELL\Registration\SharePoint.ps1:3 char:13 + Add-PsSnapin <<<< Microsoft.SharePoint.PowerShell + CategoryInfo : InvalidArgument: (Microsoft.SharePoint.PowerShell:String) [Add-PSSnapin], PSArgumentException + FullyQualifiedErrorId : AddPSSnapInRead,Microsoft.PowerShell.Commands.AddPSSnapinCommand I tried this out, too. Anybody know?

  Read the article

• What is the IPv6 equivalent to IPv4 RFC1918 addresses?

  - by Kumba

  Having a hard time wrapping my head around IPv6 here. A lot of the lingo seems targeted at enterprise-level IPv6 deployments, discussing link-local, site-local, global unicast, scopes, etc. Not a lot of solid information on really small networks, like home networks. I want to check my thinking and make sure I am getting the correct translations from IPv4-speak to IPv6-speak. The first question is, what's the equivalent of RFC1918 for IPv6? Initial searches suggested there was no equivalent. Then I stumbled upon Unique Local Addresses (RFC4193), and that states that all ULA's should be assigned the prefix fc00, followed by a 40-bit random number in the routing prefix. This random number is to "prevent collisions when two IPv6 networks are interconnected" -- again, another reference to an enterprise-level function. If I have a small local LAN at home, numbered using 192.168.4.0/24, what's my equivalent in IPv6's ULA scope? Assuming I will never, ever, tie that IPv6 address into the real internet (a router will NAT & firewall it), can I ignore the RFC to an extent and go with fc00::4:0/120? It also seems that any address in fc00::/7 are to be globally routable. Does this mean I'll need extra protections so my router would not automatically start advertising these private IPv6 addresses to the world? Second question, what's this link-local thing? Reading suggests a default-assigned address in the fe80::/10 range that has the last 64bits of the address comprised of the interface's MAC address. Seems to be required, too, but I'm annoyed by the constant discussion of it in relation to enterprise networks. Third question, what is scope id for? Seems to be yet another term tossed around in relation to enterprise networks, especially when interconnecting them, but almost no explanation on the smaller home network level. Can I see a scope ID AND CIDR notation used together? I.e., fc00::4:0/120%6, or are scope IDs only supposed to be applied to a single /128 IPv6 address?

  Read the article

• Move 53,800+ files into 54 separate folders with ~1000 files each?

  - by ane

  Trying to import 53,800+ individual files (messages) using Gmail's POP fetcher. Gmail understandably refuses, giving the error: "Too many messages to download. There are too many messages on the other server." The folder in question looks like similar to: /usr/home/customer/Maildir/cur/1203672790.V57I586f04M867101.mail.net:2,S /usr/home/customer/Maildir/cur/1203676329.V57I586f22M520117.mail.net:2,S /usr/home/customer/Maildir/cur/1203677194.V57I586f26M688004.mail.net:2,S /usr/home/customer/Maildir/cur/1203679158.V57I586f2bM182864.mail.net:2,S /usr/home/customer/Maildir/cur/1203680493.V57I586f33M740378.mail.net:2,S /usr/home/customer/Maildir/cur/1203685837.V57I586f0bM835200.mail.net:2,S /usr/home/customer/Maildir/cur/1203687920.V57I586f65M995884.mail.net:2,S ... Using the shell (tcsh, sh, etc. on FreeBSD), what one-line command can I type to split this directory full of files into separate folders so Gmail only sees 1000 messages at a time? Something with find or ls | xargs mv maybe. Whatever is fastest. The desired output directory would now look something like: /usr/home/customer/Maildir/cur/1203672790.V57I586f04M867101.mail.net:2,S /usr/home/customer/Maildir/cur/1203676329.V57I586f22M520117.mail.net:2,S ... /usr/home/customer/set1/ (contains messages 1-1000) /usr/home/customer/set2/ (contains messages 1001-2000) /usr/home/customer/set3/ (etc.) Ideally, cron could run another command to automatically reverse the process in 1000 message increments every hour. So Gmail only sees & downloads 1000 at a time.

  Read the article

• Excel chart with year-to-year comparison

  - by Craig

  Given this data: Date Year Month Usage (Kw-h) Cost/Month 02/19/08 2008 2 501 59.13 03/18/08 2008 3 404 48.49 04/16/08 2008 4 387 45.67 05/22/08 2008 5 319 37.85 06/23/08 2008 6 363 43.81 07/23/08 2008 7 372 48.86 08/21/08 2008 8 435 59.74 09/23/08 2008 9 358 49.9 10/16/08 2008 10 313 42.01 11/20/08 2008 11 328 39.99 12/16/08 2008 12 374 44.7 01/20/09 2009 1 474 55.35 02/19/09 2009 2 444 52.85 03/19/09 2009 3 398 49.25 04/17/09 2009 4 403 51.05 05/19/09 2009 5 405 49.61 06/18/09 2009 6 373 45.18 07/20/09 2009 7 337 44.67 08/18/09 2009 8 369 50.73 09/17/09 2009 9 377 52.36 10/16/09 2009 10 309 43.4 11/17/09 2009 11 249 34.14 12/16/09 2009 12 327 41.79 01/20/10 2010 1 356 45.66 I would like to produce a report that displays a Usage (Kw-h) line for each year. Features: Y axis: Usage (Kw-h) X axis: Month Line 0..n: lines representing each year's monthly Usage (Kw-h) Bonus points: instead of a line for each year, each month would have a high-low-close (HLC) bar; 'close' would be replaced by the average second Y axis and HLC bar that represents cost/month Questions: Can this be done without a Pivot table? Do I need to have the Year and Month column or can Excel automatically determine this? Current chart:

  Read the article

• Turn off monitor (energy saving) while in text console mode (in Linux)

  - by Denilson Sá

  How to configure Linux text console to automatically turn of the monitor after some time? And by "text console" I mean that thing that you get on ctrl+alt+F[1-6], which is what you get whenever X11 is not running. And, no, I'm not using any framebuffer console (it's a plain, good and old 80x25 text-mode). Many years ago, I was using Slackware Linux, and it used to boot up in text-mode. Then you would manually run startx after the login. Anyway, the main login "screen" was the plain text-mode console, and I remember that the monitor used to turn off (energy saving mode, indicated by a blinking LED) after some time. Now I'm using Gentoo, and I have a similar setup. The machine boots up in text-mode, and only rarely I need to run startx. I say this because this is mostly my personal Linux server, and there is no need to keep X11 running all the time. (which means: I don't want to use GDM/KDM or any other graphical login screen) But now, in this Gentoo text-mode console, the screen goes black after a while, but the monitor does not enter any energy-saving mode (the LED is always lit). Yes, I've waited long enough to verify this. Thus, my question is: how can I configure my current system to behave like the old one? In other words, how to make the text console trigger energy-saving mode of the monitor? (maybe I should (cross-)post this question to http://unix.stackexchange.com/ )

  Read the article

• libsasl2 change paths

  - by mk_89

  I have been following the tutorial https://help.ubuntu.com/community/Postfix for installing Postfix on ubuntu. Im stuck at the Authenication section of the tutorial where you change paths to live in the false root, if you look at the link above I have a file (/etc/default/saslauthd) which is pretty much the same as the one from the tutorial. saslauthd # This needs to be uncommented before saslauthd will be run automatically START=yes PWDIR="/var/spool/postfix/var/run/saslauthd" PARAMS="-m ${PWDIR}" PIDFILE="${PWDIR}/saslauthd.pid" # You must specify the authentication mechanisms you wish to use. # This defaults to "pam" for PAM support, but may also include # "shadow" or "sasldb", like this: # MECHANISMS="pam shadow" MECHANISMS="pam" # Other options (default: -c) # See the saslauthd man page for information about these options. # # Example for postfix users: "-c -m /var/spool/postfix/var/run/saslauthd" # Note: See /usr/share/doc/sasl2-bin/README.Debian #OPTIONS="-c" #make sure you set the options here otherwise it ignores params above and will not work OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd" When I run the following command in ubuntu dpkg-statoverride --force --update --add root sasl 755 /var/spool/postfix/var/run/saslauthd I get the following error dpkg-statoverride: warning: An override for '/var/spool/postfix/var/run/saslauthd' already exists, but --force specified so will be ignored. dpkg-statoverride: warning: --update given but /var/spool/postfix/var/run/saslauthd does not exist I don't why this is happening, I literally followed the tutorial step by step and have installed all the packages necessary, what could be the problem? do I have to manually create

  Read the article

• Router block some sites

  - by Mahesha999

  Hi I was using ADSL Modem/Router earlier. The device is quite old Pronet PN-ADSL 101 E/U model (pics: http://bit.ly/P2YaWy, http://bit.ly/OA700l) Since it had only one RJ45 out, I bought new Wireless Router TPLink TL-WR941ND. It has 4 RJ45 out and 3 wireless antennas. I configured my old router in bridge. Now, if I have to connect my pc to Internet through the old router, I have to enter username and password. Then I connected the RJ45 output of old router to the WAN in of new router. and ran the CD of new router. It configured the new router in PPPoE by saving the username and password in router to dial automatically. So now I have to just plug in the wires in my new routers any RJ45 out. I am able to access the Internet when I connect through new router (both wired and wirelessly), but some sites are getting blocked. Most notably yahoo.com (though ymail.com is working), Microsoft.com. msn.com. These sites work perfectly fine when I connect my pc directly to my old router and enter username and password manually. (However others like google.com. facebook.com works fine when connect through new router) So here these some sites need some parameter set but I am unable to find them out. Can anyone help me. My friend said he also faced same problem. Surprisingly he advised me to see if the same websites will work through Opera turbo mode and boom they worked. So what could be the problem?

  Read the article

• Windows 7 Cable Connection Rehabilitation

  - by Giovanni De Gaetano

  I recently switched the operating system of my laptop from Windows XP to Windows 7. My web-connection is such that I need to identify everytime before connecting. Since there is no automatic identification request, while using Windows XP I was used to de-abilitate and rehabilitate the cable connection after every switching on. I successfully installed the web-connection on Windows 7, and later on I switched the computer off and on (simply because I had to sleep!). After restarting the computer, since there was no automatic identification request, I de-abilitate the cable connection. But this time I didn't find any way to rehabilitate it! Do you have any suggestions on how to solve the problem? My "Wired AutoConfiguration" has the startup type "Automatic", but it's not enough to restart automatically the cable connection! I tried to do some standard things like restart the computer, unplug and plug in again the cable, reinstall the web-connection from the scratch... But nothing worked! Thank you very much for your help!

  Read the article

• Setting MSN or Yahoo! Messenger status to Invisible or Offline when idle for an hour

  - by Jian Lin

  Where, or how, do I set it up in MSN Messenger or Yahoo! Messenger to automatically switch my status to either "Invisible" or "Offline" when idle for a half hour, or an hour? I know how to set my status as "Away" or "Busy" after 10 minutes, but can't seem to find a way to set the offline status options without manual intervention. Back story As a software developer, I am very used to turning the computer on for the whole day and not turning it back off. (For example, checking email for urgent fixes, fix issue and push to web server). It's not even turned off when heading to sleep in case I might find it hard to fall asleep and come back to check on the computer. Or to have it there ready in the morning to check that everything is okay. If I'm seen as being online for 24 hours of a day, some people see me as weird. Their perception of my value decreases as I'm always there (hard to get = high value; always there = low value). Leaving it on makes everyone in my contacts list think I have nothing better to do all day than sit in front of the computer. Even though it's my job and I do admittedly spend more time online than other people. That's why I'd like to find a way to set my status as Invisible or Offline.

  Read the article

• Problems with bash script, mysql inserts and launchd

  - by Armands

  ========= I am developing a automated system, which consists of 3 parts: mysql, bash and launchd. Bash script takes folders of work related stuff, zips, archives and puts info about them into database that is located on a local MAMP server. Everything works as expected when I run the script from terminal. But when I use Launchd to automatically run this script, it functions without errors and it does not put the values into database. I've tried to make logs of returned messages, but the logs end up being empty as the command has run the way it was supposed to. Any help would be appreciated! .plist contents <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Label</key> <string>com.adevo.ari.zip</string> <key>ProgramArguments</key> <array> <string>/Volumes/Archive-Plus/B-ARCHIVE-PLUS/ZZ_UTILITY_FOLDER/Compress.sh</string> </array> <key>Nice</key> <integer>1</integer> <key>StartInterval</key> <integer>120</integer> <key>RunAtLoad</key> <true/> </dict> </plist> I made this .plist file just by searching the web.

  Read the article

< Previous Page | 312 313 314 315 316 317 318 319 320 321 322 323  | Next Page >