Search Results

Search found 17749 results on 710 pages for 'connection pool'.

Page 317/710 | < Previous Page | 313 314 315 316 317 318 319 320 321 322 323 324  | Next Page >

• Mac OS X L2TP VPN won't connect

  - by smokris

  I'm running Mac OS X Server 10.6, providing an L2TP VPN service. The VPN works just fine when connecting from all computers except one --- this one computer stays at the "Connecting..." stage for a while, then says "The L2TP-VPN server did not respond". In the console, I see this: 6/7/10 10:48:07 AM pppd[341] pppd 2.4.2 (Apple version 412.0.10) started by jdoe, uid 503 6/7/10 10:48:07 AM pppd[341] L2TP connecting to server 'foo.bar.baz.edu' (256.256.256.256)... 6/7/10 10:48:07 AM pppd[341] IPSec connection started 6/7/10 10:48:07 AM racoon[342] Connecting. 6/7/10 10:48:07 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 1). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 2). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 3). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 4). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 5). 6/7/10 10:48:11 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:14 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:17 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). ...and the "retransmit" messages continue until the error message pops up. So far I've unsuccessfully tried: rebooting deleting the VPN profile and recreating it verifying the client's internet connection (it is able to reach the VPN server) connecting through several different networks (in case a router was blocking VPN packets) disabling the Mac OS X Firewall on the client making sure that the VPN settings exactly match those of other working computers running software update (the client is on 10.6.3) Any ideas?

  Read the article

• Configuring Backup Exec 2012 using USB hard drives as media

  - by SydxPages

  I have found some information on this but have not found the exact answers to these questions. Background I have installed backup exec 2012 (with agents for databases) I have configured a storage pool, with 2 USB drives (1TB) The backups are configured to backup to one of the 2 drives (depending on which one is connected) I have 2 questions: How do I get Backup Exec to tell me which disk to insert? I have used tapes before and it told me then which tape to use? I was hoping this was available for disks too. (Whilst there are only 2 at the moment, there will be more). And then how do I get Backup Exec to delete old backups when the disk if full.

  Read the article

• Application losing Printer within Terminal Services for remote users

  - by Richard

  Question: What I need to do is have a permanent link to a printer, normally only accessible through Terminal Services (Printer Redirect), to allow Sage Line 50 layouts to see that printer persistently, even after users have disconnected and reconnected to the Terminal Services session? Although the printer is accessible each time a user connects to the Sage Server via Terminal Services, it is given a different session number and therefore the Sage Layout sees it as a different printer. History behind question: Users using Terminal Services connecting to a Sage Server on a different site Using Sage Line 50 v 15 on that Server Users want to print invoices (sage layouts) locally Sage Server cannot see the users local printers, to get around this user uses the Print redirect features of Terminal Services The individual reports can be edited to point to a specific printer by default. This means the user just has to select an invoice and click print, then select the layout/report wanted and it auto prints that invoice to the default printer specified. The problem occurs because the layouts are edited to point to the users local printer "Ricoh 1018d (session#)", note the "(session#)" as this is the users local printer being redirected through the terminal services session. Users are able to print using the sage layouts once the default printer is setup within the layout and saved, but as soon as the users disconnects from the Terminal Services session and then reconnect in the morning go to print, it has lost the connection to that printer. I understand why its failed, because that the printer is on a per session basis and the layout would not be able to hold on to the connection from a previous session. Thanks in advance for any assistance...

  Read the article

• Getting ZFS per dataset IO statistics (or NFS per export IO statistics)

  - by jkj

  Where do I find statistics about how IO is divided between zfs datasets? (zpool iostat only tells me how much IO a pool is experiencing.) All the relevant datasets are used through NFS, so I'd be happy with per export NFS IO statistics also. We're currently running OpenIndiana [edit] It seems that operation and byte counter are available in kstat kstat -p unix:*:vopstats_??????? ... unix:0:vopstats_2d90002:nputpage 50 unix:0:vopstats_2d90002:nread 12390785 ... unix:0:vopstats_2d90002:read_bytes 22272845340 unix:0:vopstats_2d90002:readdir_bytes 477996168 ... ...but the strange hexadecimal ID numbers have to be resolved from /etc/mnttab (better ideas?) rpool/export/home/jkj /export/home/jkj zfs rw,...,dev=2d90002 1308471917 Now writing a munin plugin to use the data...

  Read the article

• IIS 7.5 default permission - is restriction needed?

  - by Caroline Beltran

  I am using IIS 7.5 and I do not need to explicitly specify permissions for my ISAPI application to execute. Additionally, the application can create subdirectories, create and delete files without me specifying permissions. Since I am using the default permissions, checked to see if web.config was safe from prying eyes over the web, and it can’t be read which is good. My app also creates some .log and .ini files which are also not viewable over the web. I did notice that .txt files are viewable. I really don’t know how default permissions allow my app to do so much. Is this safe or do I need to lock down? To be honest, I don’t know what accounts to restrict. App details: My ISAPI has an ‘allowed’ entry in ISAPI and CGI Restrictions Folder and subfolders containing my application has ‘default’ permissions set. Application pool is using ‘classic’ pipeline mode and no managed code. Pass-through authentication in use. Thank you for your time

  Read the article

• Linux/Unix MTA with the smartest queue?

  - by threecheeseopera

  I am looking for an MTA that will allow me (a script, really) to proactively manage it's send queue in response to status codes returned by the remote servers I am delivering to. Basically, for each mail sent I would like to be able to react to the SMTP reply code returned by the remote server, ex. '250 OK', or to any error conditions like connection timeouts. Additionally, I would like to be able to manage the send queue moving forward based on this information, e.g. 'example.com has timed out the last 5 connection attempts, so no longer queue mail for recipients @example.com'. I am currently using postfix and perl to parse it's logs for this information, but I am playing a game of catchup that is prone to errors (out-of-order log entries etc.) and it's starting to get messy (some real ugly regexes ;). I really don't want to reinvent the wheel and use some language's smtp library; i would prefer to use a proven/fast/reliable MTA. I am however open to suggestions if what I need just isn't possible. Thanks for your help!

  Read the article

• Steps after installing vCenter Server?

  - by goober

  I'm working with: Two new ESX servers that I'm configuring A new Server 2008 R2 machine that I'm using for vCenter. I took the following steps: Installed the Hypervisor on the 2 ESX machines Checked their setup/connectivity (appears to be fine; can ping, etc.) Installed vCenter Server on the Win2k8R2 box. This included the install of a SQL Express database (we're a small shop) FYI, I changed some of the ports (443 -- 8443, 80 --8080, etc.) Installed vCenter Web Client Server on the Win2k8R2 box Problems my vSphere Client on my Desktop fails to connect. Part of this is that it asks me for a username and password, but I don't recall specifying one when I set up the install. I receive the error "vSphere Client could not connect to [machinename]. An unknown connection error occurred. (The request failed because of a connection failure. (Unable to connect to the remote server))" I have also tried to use local machine admin credentials, including the format machinename\localuseracct. I have also tried using my domain credentials which are an admin for that box. I have also checked and the service is running. I also tried to connect via vSphere client locally installed on the server. It translates "localhost" to the correct name but gives the same error. I cannot register the vCenter server from the vCenter Web Client Server. I'm not sure if this is necessary, as they're both on the same machine, but it seems like the logical next step. I also receive a "failed to connect" error in this case as well. FYI, both the vCenter server and the vCenter Web Client Server are installed on the same Win2k8R2 server. What am I missing here? What is the best way to test in this case?

  Read the article

• Ubuntu : apt-get command error

  - by Wibowo Margito

  I work with Ubuntu 10.04 everyday. Several days ago, when I release command sudo apt-get install .... it run very good, no error. I also able to open websites with my browser with no proxy. But, today, I got error. Every time I release the command, the connection redirected to an IP in my local network. I can see it in the terminal window. Several days ago I tried to connect to the internet throught the IP, by SSH tunneling. But I forget what I have done and there is no way home. This is the output in terminal : deo@deo-laptop:~$ sudo apt-get update [sudo] password for deo: Err http://cx.archive.ubuntu.com lucid Release.gpg [ Could not connect to 10.7.7.15:3128 (10.7.7.15). - connect (110: Connection timed out) Err http://cx.archive.ubuntu.com/ubuntu/ lucid/main Translation-en_US Unable to connect to 10.7.7.15:3128: 10.7.7.15 is an adress in my local network. Somebody please help me :)

  Read the article

• .htaccess error "not allowed here" for all for all instructions

  - by andres descalzo

  I am using Debian Lenny and Apache 2. I changed the default .htaccess file with: AllowOverride AuthConfig But I always get the error message not allowed here when putting any instructions in the .htaccess file. EDIT: file default: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www/ <Directory /> Options FollowSymLinks Order allow,deny Allow from all AllowOverride All </Directory> <Directory /var/www/> Options Indexes FollowSymLinks Includes #AllowOverride All #AllowOverride Indexes AuthConfig Limit FileInfo AllowOverride AuthConfig Order allow,deny Allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> .htaccess: #Options +FollowSymlinks # Prevent Directoy listing Options -Indexes # Prevent Direct Access to files <FilesMatch "\.(tpl|ini)"> Order deny,allow Deny from all </FilesMatch> # SEO URL Settings RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)\?*$ index.php?_route_=$1 [L,QSA] PHP info: apache2handler Apache Version = Apache/2.2.9 (Debian) PHP/5.2.6-1+lenny10 with Suhosin-Patch Apache API Version = 20051115 Server Administrator = webmaster@localhost Hostname:Port = hw-linux.homework:80 User/Group = www-data(33)/33 Max Requests = Per Child: 0 - Keep Alive: on - Max Per Connection: 100 Timeouts = Connection: 300 - Keep-Alive: 15 Virtual Server = Yes Server Root = /etc/apache2 Loaded Modules = core mod_log_config mod_logio prefork http_core mod_so mod_alias mod_auth_basic mod_authn_file mod_authz_default mod_authz_groupfile mod_authz_host mod_authz_user mod_autoindex mod_cgi mod_deflate mod_dir mod_env mod_mime mod_negotiation mod_php5 mod_rewrite mod_setenvif mod_status

  Read the article

• Securing a Windows Server 2008 R2 Public Web Server

  - by Denny Ferrassoli

  I'm setting up a public web server: Windows Server 2008 R2, IIS7.5. Does anyone have a tutorial / walkthrough / tips on properly securing a public web server? I've seen a few tutorials but mostly focused on Windows Server 2003. What I've done so far: Created a specific user account for the website / app pool, Renamed Admin account, Installed FTPS, Configured firewall to block any non-public service (web / https), Configured firewall to allow access to management interfaces only from specific IP addresses (rdp, IIS management, ftp) Maybe a few other things but can't remember at the moment... ICMP is allowed... Should I disable all except ping? Port scan reveals only web and https ports. Any other suggestions? Thanks

  Read the article

• Migrating to CF9: trouble getting JRun working with SSL

  - by DaveBurns

  I have a client on MX7 who wants to migrate to CF9. I have a dev environment for them on my WinXP machine where I've configured MX7 to run with JRun's built-in web server. I've had that working for a long time with both regular and SSL connections. I installed CF9 yesterday side-by-side with the existing MX7 install to start testing. The install was smooth and detected MX7, adjusted CF9's port numbers for no conflict, etc. Testing started well: MX7 over regular and SSL still worked and CF9 worked over regular HTTP. But I can't get CF9 to work with SSL. I installed a new certificate with keytool, FireFox (v3.6) complained about it being unsigned, I added it to the exception list, and now I get this: Secure Connection Failed An error occurred during a connection to localhost:9101. Peer reports it experienced an internal error. (Error code: ssl_error_internal_error_alert) I've been Googling that in all variations but can't find much help to get past this. I don't see any info in any log files either. FWIW, here's my SSL config from SERVER-INF/jrun.xml: <service class="jrun.servlet.http.SSLService" name="SSLService"> <attribute name="enabled">true</attribute>` <attribute name="interface">*</attribute> <attribute name="port">9101</attribute> <attribute name="keyStore">{jrun.rootdir}/lib/mykey</attribute> <attribute name="keyStorePassword">*deleted*</attribute> <attribute name="trustStore">{jrun.rootdir}/lib/trustStore</attribute> <attribute name="socketFactoryName">jrun.servlet.http.JRunSSLServerSocketFactory</attribute> <attribute name="deactivated">false</attribute> <attribute name="bindAddress">*</attribute> <attribute name="clientAuth">false</attribute> </service> Anyone here know of any issues re setting up SSL and CF9? Anyone had success with it? Dave

  Read the article

• What do "Unknown SSAP" and "Unknown DSAP" mean in tcpdump?

  - by lacker

  While trying to fix a problem with intermittently losing internet connection on a machine with a wireless connection to a router, I ran tcpdump and noticed packets with "Unknown SSAP" and "Unknown DSAP" errors coming at a rate of a few per second. 20:27:21.703178 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xe2 Information, send seq 0, rcv seq 16, Flags [Response], length 171 20:27:21.724726 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xe2 Information, send seq 0, rcv seq 16, Flags [Response], length 104 20:27:21.746449 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xe4 Information, send seq 0, rcv seq 16, Flags [Response], length 88 20:27:21.970963 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xe8 Information, send seq 0, rcv seq 16, Flags [Response], length 76 20:27:22.016565 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xea Information, send seq 0, rcv seq 16, Flags [Response], length 88 20:27:22.038471 00:24:a5:af:24:f6 (oui Unknown) Unknown SSAP 0xde > 1c:65:9d:48:38:95 (oui Unknown) Unknown DSAP 0xea Information, send seq 0, rcv seq 16, Flags [Response], length 171 What does the "Unknown SSAP" and "Unknown DSAP" mean, and does it indicate a problem?

  Read the article

• Authenticating Active Directory Users to Mac OS X Mavericks Server L2TP VPN Service

  - by dean

  We have a Windows Server 2012 Active Directory Infrastructure that consists of two domain controllers. Bound to the Active Directory Domain is a Mac OS X Mavericks Server 10.9.3. The server runs Profile Manager and VPN Services. My Active Directory users are able to authenticate to the Profile Manager, but not the VPN. I have found several threads on other forums of other users reporting similar issues, here is just one of many references: https://discussions.apple.com/thread/5174619 It appears as though the issue is related to a CHAP authentication failure. Can anyone suggest what next troubleshooting steps I might take? Is there a way to liberalize the authentication mechanism to include MSCHAP? Here is an excerpt of the transaction from the logs. Please note the domain has been changed to example.com. Jun 6 15:25:03 profile-manager.example.com vpnd[10317]: Incoming call... Address given to client = 192.168.55.217 Jun 6 15:25:03 profile-manager.example.com pppd[10677]: publish_entry SCDSet() failed: Success! Jun 6 15:25:03 --- last message repeated 2 times --- Jun 6 15:25:03 profile-manager.example.com pppd[10677]: pppd 2.4.2 (Apple version 727.90.1) started by root, uid 0 Jun 6 15:25:03 profile-manager.example.com pppd[10677]: L2TP incoming call in progress from '108.46.112.181'... Jun 6 15:25:03 profile-manager.example.com racoon[257]: pfkey DELETE received: ESP 192.168.55.12[4500]->108.46.112.181[4500] spi=25137226(0x17f904a) Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP connection established. Jun 6 15:25:04 profile-manager kernel[0]: ppp0: is now delegating en0 (type 0x6, family 2, sub-family 0) Jun 6 15:25:04 profile-manager.example.com pppd[10677]: Connect: ppp0 <--> socket[34:18] Jun 6 15:25:04 profile-manager.example.com pppd[10677]: CHAP peer authentication failed for alex Jun 6 15:25:04 profile-manager.example.com pppd[10677]: Connection terminated. Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP disconnecting... Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP disconnected Jun 6 15:25:04 profile-manager.example.com vpnd[10317]: --> Client with address = 192.168.55.217 has hung up

  Read the article

• Slow transfer speed between two servers

  - by Linux Guy

  I have two servers both network cards speed is 10Gbps The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.1 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.1, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.0 port 38895 connected with 0.0.0.1 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service the connection will be ok , after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• Troubleshooting iptables and configuring it to drop the priority of long-term connections

  - by intuited

  I'm somewhat familiar with the general concepts of iptables, and would like to learn it in more detail. I'm hoping that my learning experience can also be useful. The situation: I'm running dd-wrt on my router. Despite its purported QoS skills, I'm still seeing connection latency shoot up hugely whenever there's an ongoing http connection, eg some large download. Under such conditions, it can take 10 seconds or more to load a basic webpage; sometimes the connections are dropped entirely. I've tried adjusting the parameters, dropping the allotted bandwidth for up and download to well under my limit, but nothing seems to work. dd-wrt is configured to use HTB as the QoS algorithm; HFSC, although presented as an option, seems to cause the router to crash, and is rumoured to not actually work on any linux system. I'd like to be able to troubleshoot this issue and hopefully improve the settings that dd-wrt is using, but I'm finding the learning curve a bit overwhelming. For starters I am not sure what HTB actually specifies: is this a set of iptables commands, or do some of those commands specify how HTB is to be used? I would like it to prioritize based on protocol the way that it already supposed to, and in addition I'd like to have it drop the priority of connections which have a high total byte count, say over 400KB. Also tips on utilities that can be run under dd-wrt to get more info on what's going on in there are appreciated. I've tried to get iftop to work but there were issues running curses. I'm leaning towards replacing dd-wrt with openwrt; comments on this strategy are also welcome. I suspect that I would be well advised to get a second router as a standin before trying that. It may be worth noting that my total bandwidth is pretty limited (256Kbit/s).

  Read the article

• Secure PHP environments with PHP-FPM and SFTP

  - by pdd

  I'd like to set up secure environments for a small number of untrusted PHP websites on a Debian server. Right now everything runs on the same Apache2 with mod_php5 and vsftpd for administrative file access, so there is room for improvement. The idea is to use nginx instead of apache, SFTP through OpenSSH instead of vsftpd and chrooted (in sshd_config), individual users for each website with their own pool of PHP processes. All these users and nginx are part of the same group. Now in theory I can set 700 permissions on all PHP scripts and 750 on static files that nginx has to serve up. Theoretically, if a website is compromised all the other users' data is safe, right? Are there better solutions that require less setup time and memory per website? Cheers

  Read the article

• Access to NTP via IP which doesn't change often

  - by faulty

  I'm trying to sync the clock of our production server located in a data center with pool.ntp.org. For security reason, our servers has no internet access unless we requested to open specific ip/port explicitly. I worked out a list of IPs based on 0.asia.ntp.org 1.asia.ntp.org 2.asia.ntp.org 3.asia.ntp.org Not realizing ntp.org is using round robin DNS and the servers being voluntary, they changes from time to time. In fact the IP I've got from 3.asia.ntp.org last month is no longer working now. I'm wondering if there's a publicly known NTP server that doesn't change as often or if there's a way to go around this without having to request an update to the firewall on a monthly basis. I believe many admin is facing the same issue here.

  Read the article

• Change which server mailbox is associated with in Exchange 2007

  - by tacos_tacos_tacos

  I have restored and mounted an EDB file onto a new Exchange 2007 Server. However, the old server is still online and although all the mailboxes I need are in the newly-mounted database, in Exchange 2007 System Manager it still shows that the mailbox is associated with the old server. If I try to "Move" the database it actually tries to copy the files from the old server to the new server, which is not necessary because they are already there - and produces and error about the mailbox on the destination already existing. How can I simply tell Exchange (AD?) to use the new server to find the mailbox rather than the old? Edit: I did the restore by taking the old server offline (turning off all Exchange services), copying EDB file to the new server, restoring it with eseutil, and mounting it to the new server. I did it this way in part because I didn't know a better way and in part because I couldn't use move-mailbox as the source location had a horrible Internet connection (which is why Exchange is being moved to the new location). I had to copy the EDB from the old server to a hard disk, go somewhere with a better Internet connection, upload the EDB to the new server.

  Read the article

• Windows 2008 R2 forgets static IP configuration after reboot

  - by Andrew

  I've got an issue where a Windows 2008 R2 Standard (SP1) server loses its static IP configuration upon a reboot. It's a sysprep'd image. The following steps reproduces the problem: Using the SAC, set the IP using 'i' Use the Win32 EnableStatic() method to set an IP (and then SetGateways()) through PowerShell Reboot The machine boots up with the following configuration: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : [...] Autoconfiguration IPv4 Address. . : 169.254.152.31 (incorrect) Subnet Mask . . . . . . . . . . . : 255.255.0.0 (incorrect, was set to /24) Default Gateway . . . . . . . . . : 1.1.1.1 (correct) Occasionally, the gateway is also incorrect (0.0.0.0) The images have a script that runs 'netsh int ip reset' after sysprep finishes (before the reboot), so it appears that does not solve the issue. (the problem also happens without this step) After the reboot, using 'i' on the SAC resolves the issue permanently. (But I'd like to know the root cause as having to run 'i' again isn't ideal)

  Read the article

• Apache 403 after configuring varnish

  - by w0rldart

  I just don't know where else to look and what else to do. I keep getting a 403 error on all my vhosts after setting varnish 3.0 Apacher log: [error] [client 127.0.0.1] client denied by server configuration: /etc/apache2/htdocs Headers: http://domain.com/ GET / HTTP/1.1 Host: domain.com User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:16.0) Gecko/20100101 Firefox/16.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-US,en;q=0.5 Accept-Encoding: gzip, deflate DNT: 1 Connection: keep-alive Cookie: __utma=106762181.277908140.1348005089.1354040972.1354058508.6; __utmz=106762181.1348005089.1.1.utmcsr=OTHERDOMAIN.com|utmccn=(referral)|utmcmd=referral|utmcct=/galerias/cocinas Cache-Control: max-age=0 HTTP/1.1 403 Forbidden Vary: Accept-Encoding Content-Encoding: gzip Content-Type: text/html; charset=iso-8859-1 X-Cacheable: YES Content-Length: 223 Accept-Ranges: bytes Date: Sat, 01 Dec 2012 20:35:14 GMT X-Varnish: 1030961813 1030961811 Age: 26 Via: 1.1 varnish Connection: keep-alive X-Cache: HIT ---------------------------------------------------------- /etc/default/varnish: DAEMON_OPTS="-a ip.ip.ip.ip:80 \ -T localhost:6082 \ -f /etc/varnish/main.domain.vcl \ -S /etc/varnish/secret \ -s file,/var/lib/varnish/$INSTANCE/varnish_storage.bin,1G" #-s malloc,256m" My vcl file: http://pastebin.com/axJ57kD8 So, any ideas what I could be missing? Update Just so you know, ports: NameVirtualHost *:8000 Listen 8000 and <VirtualHost 205.13.12.12:8000>

  Read the article

• ssh timeout issue connecting to an EC2 instance on OS X

  - by mamusr

  I am new to AWS and not a networking expert but curious to know more about it. I created a VPC with a public subnet only. Then i created an EC2 instance using an Ubuntu 14.04 64-bit pv AMI image (ami-e84d8480) as well generating the key pair needed to connect to it through ssh. I followed amazon's instructions to connect to an EC2 instance via ssh which did not work. Here is my attempted input and debug log: Running on OS X 10.9.4 user$ ssh -vvv -i key.pem [email protected] OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 102: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to xxx.xxx.xxx.xxx [xxx.xxx.xxx.xxx] port 22. debug1: connect to address xxx.xxx.xxx.xxx port 22: Operation timed out ssh: connect to host xxx.xxx.xxx.xxx port 22: Operation timed out To attempt to resolve the issue: I enabled the SSH port. Tried different usernames other than ubuntu, like ec2-user and root. Initially set an inbound ssh rule in the security group to connect to only my ip address. When that did not work, i changed it to allow any ip to connect. But those actions did not fix the problem. Here are my guesses as to what i am missing in getting the EC2 instance connection to work. My etc/ssh_config file may be preventing the connection from taking place. I may have missed an important networking detail when setting up the VPC. I do not have a public ip address specified for the instance. I am connecting through the private ip address. My questions for the community: Am i going about it the wrong way connecting to the instance through the private ip address? if so, do i need to specify a public ip address for it to connect or some other method?

  Read the article

• SocketException (Timeout) only when running as scheduled task

  - by BVartin

  I'm running a C# web-scrapper application (that I wrote) on a Windows Server 2003 instance under a user belonging to the local Administrator group. When I run it within a desktop/remote-desktop session the application runs successfully but when I schedule it to run under the same user/security-context outside of the desktop session, all socket connections timeout. The scheduled task calls a batch file which in-turn calls the application. The Windows Server 2003 instance has a very basic configuration and isn't even connected to a domain. I cannot find anything in any firewall or security configuration which is preventing this but maybe I have overlooked something, can anyone be of any assistance? System.Net.WebException: Unable to connect to the remote server --- System.Net.Sockets.SocketException: A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond X.X.X.X:443 at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress) at System.Net.ServicePoint.ConnectSocketInternal(Boolean connectFailure, Socket s4, Socket s6, Socket& socket, IPAddress& address, ConnectSocketState state, IAsyncResult asyncResult, Int32 timeout, Exception& exception) --- End of inner exception stack trace --- at System.Net.HttpWebRequest.GetResponse()

  Read the article

• How do I SSH tunnel using PuTTY or SecureCRT through gateway/proxy to development server?

  - by DAE51D

  We have some unix boxes setup in a way that to get to the development box via ssh, you have to ssh into a 'user@jumpoff' box first. There is no direct connection allowed on 'dev' via ssh from anywhere but 'jumpoff'. Furthermore, only key exchange is allowed on both servers. And you always login to the development box as 'build@dev'. It's painful to always do that hopping. I know this can be done with SOCKS or a Tunnel or something... I have setup a FreeBSD VM and I can get things to work awesome using unix ssh tools. Basically all I do is make sure my vm's ~/.ssh/id_rsa.pub key is on both jumpoff and dev and use this ~/.ssh/config file: # Development Server Host ext-dev # this must be a resolvable name for "dev" from Jumpoff Hostname 1.2.3.4 User build IdentityFile ~/.ssh/id_rsa # The Jumpoff Server Host ext Hostname 1.1.1.1 User daevid Port 22 IdentityFile ~/.ssh/id_rsa # This must come below all of the above Host ext-* ProxyCommand ssh ext nc $(echo '%h'|cut -d- -f2-) 22 Then I just simply type "ssh ext-dev" and I'm in like Flynn. The problem is I can't get this same thing to work using either PuTTY or SecureCRT -- and to be honest I've not found any tutorials that really walk me through it. I see many on setting up some kind of proxy tunnel for Firefox, but it doesn't seem to be the same concept. I've been messing with various trial and error most all day and nothing has worked (obviously) and I'm at the end of my ssh knowledge and Google searching. I found this link which seemed to be perfect, but it doesn't work for me. The "Master" connects fine, but the "client" portion doesn't connect. It tells me, the remote system refused the connection. http://www.vandyke.com/support/tips/socksproxy.html I've got the VM, PuTTY and SecureCRT all using the same public/private key pairs to make things consistent and easier to debug. Does anyone have a straight up example of how to do this in Windows?

  Read the article

• IPTables: NAT multiple IPs to one public IP

  - by Kaemmelot

  I'm looking for a way how to nat 2 or more inner IPs (in my case xen doms) to one outer IP. I tried to use iptables -t nat -A PREROUTING -d 123.123.123.123 -j DNAT --to 1.2.3.4 --to 1.2.3.7 iptables -t nat -A POSTROUTING -s 1.2.3.4 -j SNAT --to 123.123.123.123 iptables -t nat -A POSTROUTING -s 1.2.3.7 -j SNAT --to 123.123.123.123 And got an error: iptables v1.4.14: DNAT: Multiple --to-destination not supported Try `iptables -h' or 'iptables --help' for more information. I found this in the manpage: Later Kernels (= 2.6.11-rc1) don't have the ability to NAT to multiple ranges anymore. So my question is: Why is it not possible anymore and is there a workaround? Maybe I should use an other method I don't know yet? EDIT: The idea is to use the system like a router, so I have one address but multiple users behind. The problem is I don't know which connection reffers to a user (for example 1.2.3.4). But I know, they all have different ports open for incomming traffic. So my solution (for DNAT) would be to nat all incoming connections to all users and filter all unused ports, so the connection goes to one single user. For outgoing traffic I would use iptables -A FORWARD -i eth0 -d 1.2.3.4 -m state --state ESTABLISHED,RELATED -j ACCEPT

  Read the article

• IIS 8 Random 503 service unavailable

  - by Ivo

  We migrated a busy website to Windows Server 2012 with IIS 8. The website randomly gives the error "503 service unavailable" after an user presses F5 the error is gone again. The website is build in ASP.NET MVC 3. The website runs on one application pool, with default settings There are around 500 to 900 concurrent users on the website during the day, and the error happens more often when there are more 650 users. The CPU and the memory use on the server is stable. There is nothing about the 503 errors in the application log, the IIS log and the event log. Does anyone has any clue what the problem can be or how we can trace the the problem?

  Read the article

< Previous Page | 313 314 315 316 317 318 319 320 321 322 323 324  | Next Page >