Search Results

Search found 17749 results on 710 pages for 'connection pool'.

Page 315/710 | < Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >

• Linux Kernel Packet Forwarding Performance

  - by Bob Somers

  I've been using a Linux box as a router for some time now. Nothing too fancy, just enabling forwarding in the kernel, turning on masquerading, and setting up iptables to poke a few holes in the firewall. Recently a friend of mine pointed out a performance problem. Single TCP connections seem to experience very poor performance. You have to open multiple parallel TCP connections to get decent speed. For example, I have a 10 Mbit internet connection. When I download a file from a known-fast source using something like the DownThemAll! extension for Firefox (which opens multiple parallel TCP connections) I can get it to max out my downstream bandwidth at around 1 MB/s. However, when I download the same file using the built-in download manager in Firefox (uses only a single TCP connection) it starts fast and the speed tanks until it tops out around 100 KB/s to 350 KB/s. I've checked the internal network and it doesn't seem to have any problems. Everything goes through a 100 Mbit switch. I've also run iperf both internally (from the router to my desktop) and externally (from my desktop to a Linux box I own out on the net) and haven't seen any problems. It tops out around 1 MB/s like it should. Speedtest.net also reports 10 Mbits speeds. The load on the Linux machine is around 0.00, 0.00, 0.00 all the time, and it's got plenty of free RAM. It's an older laptop with a Pentium M 1.6 GHz processor and 1 GB of RAM. The internal network is connected to the built in Intel NIC and the cable modem is connected to a Netgear FA511 32-bit PCMCIA network card. I think the problem is with the packet forwarding in the router, but I honestly am not sure where the problem could be. Is there anything that would substantially slow down a single TCP stream?

  Read the article

• Openconnect for Cisco VPN doesn't recognize private key file - asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag

  - by Alexander Skwar

  I'm trying to use my Synology DS212 NAS box also act as VPN gateway to my companies VPN. Sadly, they only use Cisco ASA and to complicate stuff even further, we've got to use personal certificates (which is of course more secure, but more complicate to get going…). So I compiled OpenConnect v4.06 from http://www.infradead.org/openconnect/. As a very basic test, I tried to build a connection by manually invoking openconnect, passing along the key and cert files, like so: /lib/ld-linux.so.3 --library-path /opt/lib \ /opt/openconnect/sbin/openconnect \ --certificate=$VPN_CFG/alexander.crt \ --sslkey=$VPN_CFG/alexander.key \ --cafile=$VPN_CFG/Company_VPN_CA.crt \ --user=alexander --verbose <ip>:443 It fails :( Attempting to connect to <ip>:443 Using certificate file $VPN_CFG/alexander.crt Using client certificate '/[email protected]/OU=Company VPN' 5919:error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag:tasn_dec.c:1315: Loading private key failed (see above errors) Loading certificate failed. Aborting. Failed to open HTTPS connection to <ip> Failed to obtain WebVPN cookie When I run the same command with the same cert/key files on a Ubuntu 12.04 box, it works: openconnect \ --certificate=$VPN_CFG/alexander.crt \ --sslkey=$VPN_CFG/alexander.key \ --cafile=$VPN_CFG/Company_VPN_CA.crt \ --user=alexander --verbose <ip>:443 Attempting to connect to <ip>:443 Using certificate file $VPN_CFG/alexander.crt Extra cert from cafile: '/CN=Company AG VPN CA/O=Company AG/L=Zurich/ST=ZH/C=CH' SSL negotiation with <ip> Server certificate verify failed: self signed certificate Certificate from VPN server "<ip>" failed verification. Reason: self signed certificate Enter 'yes' to accept, 'no' to abort; anything else to view: yes Connected to HTTPS on <ip> GET https://<ip>/ […] Well… The error on the NAS is this: 5919:error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag:tasn_dec.c:1315: Any ideas, what's causing this? On Syno, I use OpenConnect 4.06. On Ubuntu, I just compiled and installed to a custom location OpenConnect 4.06 as well. Thanks, Alexander

  Read the article

• DD-WRT PPTP VPN problem

  - by Tobias Tromm

  I try to configure a DD-WRT as a PPTP client. The VPN Server is Windows Server 2003. This is my scenario: The Windows 2003 Server has set to give to the VPN Client the 10.0.0.81 fixed IP and to add a network route to the remote home. At the remote home I have changed the PPTP Options at DD-WRT to make the connection. The VPN connection is successfully established. ...and Windows successfully add the route to the remote home 192.168.2.X. From the remote home I can successfully access any computer from the VPN server side. The problem is when I try to access the remote home from the Server side. From Server side I only can access\ping DD-WRT ( by VPN Client IP - 10.0.0.81). What's wrong? How I need to do to be a site-to-site VPN? This is what happen when I try to tracert the remote home from local home.

  Read the article

• Ubuntu 12.04 Server - eth0 1Gbps NIC eth1 10Gbps NIC - all traffic using eth0?

  - by James

  Ubuntu Server 12.04.1 x64 Primary role is an NFS fileserver, for Mac OSX Clients. Hardware: Eth0: 00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 04) Eth1: 07:00.0 Ethernet controller: MYRICOM Inc. Myri-10G Dual-Protocol NIC Config: ifconfig eth0 Link encap:Ethernet HWaddr <MACADDRESS> inet addr:192.168.0.150 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:460042020 errors:0 dropped:148 overruns:0 frame:0 TX packets:231906707 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:581431978417 (581.4 GB) TX bytes:259057368617 (259.0 GB) Interrupt:20 Memory:f7d00000-f7d20000 eth1 Link encap:Ethernet HWaddr <MACADDRESS> inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6832208 errors:0 dropped:2 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:513826442 (513.8 MB) TX bytes:33688 (33.6 KB) Interrupt:59 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:507 errors:0 dropped:0 overruns:0 frame:0 TX packets:507 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:45057 (45.0 KB) TX bytes:45057 (45.0 KB) nano /etc/network/interfaces #The loopback network interface auto lo iface lo inet loopback #The primary network interface auto eth0 iface eth0 inet static address 192.168.0.150 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 #second network interface auto eth1 iface eth1 inet static address 192.168.0.100 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 Currently I am using on the OSX clients: nfs://192.168.0.100/Volumes/Storage to mount the NFS share. My problem is why would all the data (and I have checked using various monitoring tools bmon, iftop, glances, etc) be going over the slower connection?? Also, after configuring /etc/network/interfaces with the above setup I always get an error message at bootup something about waiting for network configuration. Are these connected?

  Read the article

• iPhone Remote with iTunes Library via VPN

  - by sudo work

  Alright, so I'm currently behind a network router (not under my control). The router performs NAT and somehow prevents a computer from scanning other nodes. At least, you're unable, in this instance, to locate an iTunes library. You can, however, communicate with a node's open ports if the local IP address is known, as well as the port. I haven't actually tried port scanning a specific IP using nmap or another tool yet. So I've tried one solution to remove the contribution of the router entirely (to verify that it works without the influence of the routers). I set up an access point using my iPhone and tethered my computer (with the library) to it. From here, I was able to pair my library and the iPhone Remote application. Control of the library was normal as well. This solution is not ideal, however, because I am actively using bandwidth with my computer and cannot afford to be tethered to my 3G connection. A viable solution for me is to use a common VPN connection, which I have set up on a Ubuntu (Intrepid) server that is remote. Both my computer and iPhone are able to access the VPN via PPTP. The server is setup with PPTPD as the VPN-server; I'm using IPTables to perform IP masquerading and forwarding traffic. I however, still cannot connect the library to the phone. I can however, see both devices on the VPN subnet (192.168.0.0/24). SSH'ing and such works fine. What settings on the VPN server must I change to get this to work? Also, how can I assign static IP addresses to various PPTP clients based on MAC addresses?

  Read the article

• Application losing Printer within Terminal Services for remote users

  - by Richard

  Question: What I need to do is have a permanent link to a printer, normally only accessible through Terminal Services (Printer Redirect), to allow Sage Line 50 layouts to see that printer persistently, even after users have disconnected and reconnected to the Terminal Services session? Although the printer is accessible each time a user connects to the Sage Server via Terminal Services, it is given a different session number and therefore the Sage Layout sees it as a different printer. History behind question: Users using Terminal Services connecting to a Sage Server on a different site Using Sage Line 50 v 15 on that Server Users want to print invoices (sage layouts) locally Sage Server cannot see the users local printers, to get around this user uses the Print redirect features of Terminal Services The individual reports can be edited to point to a specific printer by default. This means the user just has to select an invoice and click print, then select the layout/report wanted and it auto prints that invoice to the default printer specified. The problem occurs because the layouts are edited to point to the users local printer "Ricoh 1018d (session#)", note the "(session#)" as this is the users local printer being redirected through the terminal services session. Users are able to print using the sage layouts once the default printer is setup within the layout and saved, but as soon as the users disconnects from the Terminal Services session and then reconnect in the morning go to print, it has lost the connection to that printer. I understand why its failed, because that the printer is on a per session basis and the layout would not be able to hold on to the connection from a previous session. Thanks in advance for any assistance...

  Read the article

• How to make DD-WRT router's (configured like a repeater) devices be accessible on LAN? (i.e. integrate DHCP for both routers)

  - by Annonomus Penguin

  I have a D-Link DIR-600-A1 router running DD-WRT (using the 601's firmware: except for the model number, they are near identical). It has an Atheros chip, so there is no "repeater" option. You can bypass this by setting the main radio as a client to the main router, and adding a virtual radio configured as an AP. You can then set up the credentials for connecting to the main router and allowing devices to connect to the repeater/router. I have a few devices on my network: Ethernet computers Server with Samba running WiFi devices connected to the main router I then wanted to add a repeater. I have a couple of other things on the repeater: WiFi Computer Other WiFi devices. Anyway, I wanted to connect my WiFi computer to the share on my server via Samba. However, for some reason, my router treats the main router as WAN, not another device. I've tried disabling the SPI firewall: However, that doesn't work. I've tried pinging my WiFi computer from my server. However, I can ping my server from my WiFi computer. AFAIK, they are on the same subset, just using different IPs: the main one uses 192.168.0.x and the repeater uses 192.168.1.x (starting at 100 for some reason). It seems as I need to configure my router(s) to work together for DHCP. I noticed there was a "DHCP forwarder" option, but I have no idea what that would do. A quick note: for some reason (that's beyond me) my ISP disabled the capability to bridge a WiFi to ethernet connection with the router they provide (something about PPPoE or similar...). The service rep I talked to when I was having issues after I changed ISPs said that, but they couldn't explain exactly what they were "blocking." How can I get DD-WRT to not treat the client connection as WAN and the router to recognize the devices connected to the repeater?

  Read the article

• Ubuntu Postfix Gmail SMTP Relay Not Working

  - by Nick DeMayo

  I currently have postfix set up to relay messages from my websites through gmail, and up until recently it was working perfectly. However, within the last week or so (not really sure when) I started getting the below error whenever attempting to send an email: Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[2001:4860:800a::6c]:587: Network is unreachable Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[173.194.76.109]:587: Connection refused Jul 20 07:40:46 localhost postfix/smtp[11958]: connect to smtp.gmail.com[173.194.76.108]:587: Connection refused Here is my configuration file: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h #readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = [my domain name] alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases #myorigin = /etc/mailname mydestination = [my host name], localhost.localdomain, localhost relayhost = [smtp.gmail.com]:587 mynetworks = 127.0.0.0/8 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = loopback-only inet_protocols = all ########################################## ##### non debconf entries start here ##### ##### client TLS parameters ##### smtp_tls_loglevel=1 smtp_tls_security_level=encrypt smtp_sasl_auth_enable=yes smtp_sasl_password_maps=hash:/etc/postfix/sasl/passwd smtp_sasl_security_options = noanonymous ##### map username@localhost to [email protected] ##### smtp_generic_maps=hash:/etc/postfix/generic Nothing changed on my server, as far as I know...any ideas what could have caused it to stop working?

  Read the article

• Munin node not listing any plugins on new Fedora 14 installation

  - by Dave Forgac

  I have just installed munin-node from the base repo on Fedora 14 and then started it. I found that my munin server is not able to collect data from this node so I tried connecting via telnet to test. When connecting via telnet I see that no plugins are listed: [dave@host ~]# telnet localhost 4949 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. # munin node at host.example.com list quit Connection closed by foreign host. [dave@host ~]# I did not modify anything after the installation. The munin-node.conf is allowing connections from 127.0.0.1 and the default set of plugins in /etc/munin/plugins/ are symlinked to the plugins in /usr/share/munin/plugins/. Here is the working output of the telnet test of the 'list' command should look like (this is on a Fedora 13 host): [dave@www ~]$ telnet localhost 4949 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. # munin node at www.example.com list apache_accesses apache_processes apache_volume cpu df df_inode entropy forks fw_packets if_err_eth0 if_err_eth1 if_eth0 if_eth1 interrupts iostat iostat_ios irqstats load memory munin_stats mysql_ mysql_bytes mysql_innodb mysql_queries mysql_slowqueries mysql_threads netstat open_files open_inodes postfix_mailqueue postfix_mailvolume proc_pri processes swap threads uptime users vmstat yum quit Connection closed by foreign host. [dave@www ~]$ Edited to show output of munin-node-configure: [root@host ~]# munin-node-configure Plugin | Used | Extra information ------ | ---- | ----------------- acpi | no | amavis | no | ... http_loadtime | no | if_ | yes | eth1 eth0 if_err_ | yes | eth0 eth1 ifx_concurrent_sessions_ | no | interrupts | yes | ... uptime | yes | users | yes | varnish_ | no | vserver_resources | no | yum | yes | zimbra_ | no | Any suggestions on what to check next?

  Read the article

• Howo to get Multipath IO with Dell MD3600i into active/active setup?

  - by Disco

  I'm desperately trying to improve performance of my SAN connection. Here's what i have: [root@xnode1 dell]# multipath -ll mpath1 (36d4ae520009bd7cc0000030e4fe8230b) dm-2 DELL,MD36xxi [size=5.5T][features=3 queue_if_no_path pg_init_retries 50][hwhandler=1 rdac][rw] \_ round-robin 0 [prio=200][active] \_ 18:0:0:0 sdb 8:16 [active][ready] \_ 19:0:0:0 sdd 8:48 [active][ghost] \_ 20:0:0:0 sdf 8:80 [active][ghost] \_ 21:0:0:0 sdh 8:112 [active][ready] And multipath.conf : defaults { udev_dir /dev polling_interval 5 prio_callout none rr_min_io 100 max_fds 8192 user_friendly_names yes path_grouping_policy multibus default_features "1 fail_if_no_path" } blacklist { device { vendor "*" product "Universal Xport" } } devices { device { vendor "DELL" product "MD36xxi" path_checker rdac path_selector "round-robin 0" hardware_handler "1 rdac" failback immediate features "2 pg_init_retries 50" no_path_retry 30 rr_min_io 100 prio_callout "/sbin/mpath_prio_rdac /dev/%n" } } And sessions. [root@xnode1 dell]# iscsiadm -m session tcp: [13] 10.0.51.220:3260,1 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c tcp: [14] 10.0.50.221:3260,2 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c tcp: [15] 10.0.51.221:3260,2 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c tcp: [16] 10.0.50.220:3260,1 iqn.1984-05.com.dell:powervault.md3600i.6d4ae520009bd7cc000000004fd7507c I'm getting very poor read performance : dd if=/dev/mapper/mpath1 of=/dev/null bs=1M count=1000 The SAN is configured as follows: CTRL0,PORT0 : 10.0.50.220 CTRL0,PORT1 : 10.0.50.221 CTRL1,PORT0 : 10.0.51.220 CTRL1,PORT1 : 10.0.51.221 And on the host : IF0 : 10.0.50.1 IF1 : 10.0.51.1 (Dual 10GbE Ethernet Card Intel DA2) It's connected to a 10gbE switch dedicated for SAN traffic. My questions being; why the connection is set up as 'ghost' and not 'ready' like an active/active configuration ?

  Read the article

• ProFTPD / PAM issues with new centos/virtualmin install

  - by iamthewit

  I just installed CentOS 5.4 on a rackspace cloud server and installed virtualmin which all seemed to go fine. The only problem I have is that I can not access the virtual servers directories via FTP. I get the following from filezilla: Status: Connecting to 1.1.1.1:21... Status: Connection established, waiting for welcome message... Response: 220 FTP Server ready. Command: USER username Response: 331 Password required for username. Command: PASS *************** Response: 230 User username logged in. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is current directory. Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (1,1,1,1,216,214) Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing and I get this from my /var/secure/log file Sep 22 19:40:42 stickeeserver proftpd: pam_unix(proftpd:session): session opened for user username by (uid=0) Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - USER nastypasty: Login successful. Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - Preparing to chroot to directory '/home/username' Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - mod_delay/0.5: delaying for 728 usecs Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - error setting IPV6_V6ONLY: Protocol not available Any help would be greatly appreciated, I'm not totally new to Linux but it's not my strongest subject. I do like to know exactly why problems occur though and how exactly to fix them so the more detail the better! cheers

  Read the article

• FTP on Linux "Failed to retrieve directory listing" not firewall issue

  - by Jaka Prasnikar

  I've got an VPS in germany running Debian X64. I have very strange issue. I have ISPConfig CP installed using proftpd and I can not connect to FTP by any means. Few hours ago I've had installed DirectAdmin on CentOS same VPS and same issue. Simply when I connect to FTP server I get these: Status: Resolving address of web02.defikon.com Status: Connecting to 130.255.190.71:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [privsep] [TLS] ---------- Response: 220-You are user number 1 of 50 allowed. Response: 220-Local time is now 12:15. Server port: 21. Response: 220-This is a private system - No anonymous login Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 15 minutes of inactivity. Command: USER default1 Response: 331 User default1 OK. Password required Command: PASS ****** Response: 230-User default1 has group access to: client0 sshusers Response: 230 OK. Current restricted directory is / Command: OPTS UTF8 ON Response: 200 OK, UTF-8 enabled Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is your current location Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PASV Error: Connection timed out Error: Failed to retrieve directory listing I even tried telnet localhost 21 and the same happends. Once I issue command "LIST" I get time out. I've tried every thing and I can't get this to work =( Please help ! P.S.: iptables is turned off.

  Read the article

• SSH hangs without password prompt

  - by Wilco

  Just reinstalled OS X and for some reason I now cannot connect to a specific machine on my local network via SSH. I can SSH to other machines on the network without any problems, and other machines can SSH to the problematic one as well. I'm not sure where to start looking for problems - can anyone point me in the right direction? Here's a dump of a connection attempt: OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to 10.0.1.7 [10.0.1.7] port 22. debug1: Connection established. debug1: identity file /Users/nwilliams/.ssh/identity type -1 debug1: identity file /Users/nwilliams/.ssh/id_rsa type -1 debug1: identity file /Users/nwilliams/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_4.5 debug1: match: OpenSSH_4.5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '10.0.1.7' is known and matches the RSA host key. debug1: Found key in /Users/nwilliams/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password,keyboard-interactive debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic ... at this point it hangs for quite a while, and then resumes ... debug1: Unspecified GSS failure. Minor code may provide more information Server not found in Kerberos database debug1: Unspecified GSS failure. Minor code may provide more information Server not found in Kerberos database debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Trying private key: /Users/nwilliams/.ssh/identity debug1: Trying private key: /Users/nwilliams/.ssh/id_rsa debug1: Trying private key: /Users/nwilliams/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive

  Read the article

• Is there any way for ME to improve routing to an overseas server?

  - by Simon Hartcher

  I am trying to make a connection to a gaming server in Asia from Australia, but my ISP routes my connection through the US. Tracing route to worldoftanks-sea.com [116.51.25.54]over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 192.168.1.1 2 34 ms 42 ms 45 ms 10.20.21.123 3 40 ms 40 ms 43 ms 202.7.173.145 4 51 ms 42 ms 36 ms syd-sot-ken-crt1-ge-6-0-0.tpgi.com.au [202.7.171.121] 5 175 ms 200 ms 195 ms ge5-0-5d0.cir1.seattle7-wa.us.xo.net [216.156.100.37] 6 212 ms 228 ms 229 ms vb2002.rar3.sanjose-ca.us.xo.net [207.88.13.150] 7 205 ms 204 ms 206 ms 207.88.14.226.ptr.us.xo.net [207.88.14.226] 8 207 ms 215 ms 220 ms xe-0.equinix.snjsca04.us.bb.gin.ntt.net [206.223.116.12] 9 198 ms 201 ms 199 ms ae-7.r20.snjsca04.us.bb.gin.ntt.net [129.250.5.52] 10 396 ms 391 ms 395 ms as-6.r20.sngpsi02.sg.bb.gin.ntt.net [129.250.3.89] 11 383 ms 384 ms 383 ms ae-3.r02.sngpsi02.sg.bb.gin.ntt.net [129.250.4.178] 12 364 ms 381 ms 359 ms wotsg1-slave-54.worldoftanks.sg [116.51.25.54] Trace complete. Since I think it will be unlikely that my ISP will do anything, are there any ways to improve my routing to the server without them having to intervene? NB. The game runs predominately over UDP, so I believe most low ping services are out of the question, as they rely on TCP traffic.

  Read the article

• WHS - Windows Update Failure

  - by Kyle B.

  Clicking "Update Now..." inside my EX470 control panel for Windows Update produces the following error message: "Windows Home Server updates installation can not complete. Please try again later. If the problem persists, please restart the server." I have rebooted the server numerous times, and I have also used remote desktop to connect to the machine to perform the update this way, however the browser is unable to pull up http://windowsupdate.microsoft.com. This is very strange behavior because I am able to access all other sites (gmail.com, serverfault.com, etc). Would it be possible for someone to explain to me how I can check to see what is blocking the connection of this device, which apparently has a valid internet connection, to the Microsoft Windows Update site? note #1 Using the shortcut: %SystemRoot%\system32\wupdmgr.exe does not work either. It says "Connecting to 65.55.200.155..." but nothing ever happens. This is strange because all other sites seem fine. Also, I can connect to windowsupdate.microsoft.com on my local desktop so I know this is running as well

  Read the article

• BES Express - configure MDS to push messages from 3rd party web application

  - by Max Gontar

  Hi! I have developed IIS web service to send PAP messages using Blackberry Push API over MDS. And there is an application installed on device, configured to receive push messages on appropriate port. Everything works well on MDS simulator. But it's not working well in real environment: I have installed BES Express and register several devices. I can browse MDS url with appropriate port, so url is correct. Also port enabled for reliable pushes is used in push message and in device application. Here is MDS simulator log: <2011-01-12 14:00:03.456 EET>:[272]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = PapServlet: request from 0:0:0:0:0:0:0:1 564 bytes...> <2011-01-12 14:00:03.476 EET>:[273]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Mapping PAP request to push request for pushID:pushID:asdas> <2011-01-12 14:00:03.479 EET>:[274]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = PushServlet: POST request from [UNKNOWN @ 0:0:0:0:0:0:0:1] to [PAPDEST=WAPPUSH%3D2100000A%253A100%2FTYPE%3DUSER%40rim.net&PORT=100&REQUESTURI=/] : -1 bytes...> <2011-01-12 14:00:03.480 EET>:[275]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = submitting push message with id:pushID:asdas> <2011-01-12 14:00:03.482 EET>:[276]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Executing push submit command for pushID:pushID:asdas> <2011-01-12 14:00:03.483 EET>:[278]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Pushing message to: 2100000a> <2011-01-12 14:00:03.484 EET>:[279]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Number of active push connections:1> <2011-01-12 14:00:03.489 EET>:[280]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = added server-initiated connection = -872546301, push id = pushID:asdas> <2011-01-12 14:00:03.491 EET>:[281]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Available threads in DefaultJobPool = 9 running JobRunner: DefaultJobRunner-7> <2011-01-12 14:00:03.494 EET>:[282]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = ReceivedFromServer, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION => <2011-01-12 14:00:03.494 EET>:[282]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = ReceivedFromServer, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Transmission Line Section]:> <2011-01-12 14:00:03.494 EET>:[282]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = ReceivedFromServer, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = POST / HTTP/1.1> <2011-01-12 14:00:03.494 EET>:[282]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = ReceivedFromServer, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Headers Section]: 8 headers> <2011-01-12 14:00:03.494 EET>:[282]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = ReceivedFromServer, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Parameters Section]: 3 parameters> <2011-01-12 14:00:03.499 EET>:[283]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = SentToDevice, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION => <2011-01-12 14:00:03.499 EET>:[283]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = SentToDevice, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Transmission Line Section]:> <2011-01-12 14:00:03.499 EET>:[283]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = SentToDevice, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = POST / HTTP/1.1> <2011-01-12 14:00:03.499 EET>:[283]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = SentToDevice, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Headers Section]: 9 headers> <2011-01-12 14:00:03.499 EET>:[283]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, HANDLER = HTTP, EVENT = SentToDevice, DEVICEPIN = 2100000a, CONNECTIONID = -872546301, HTTPTRANSMISSION = [Parameters Section]: 3 parameters> <2011-01-12 14:00:03.501 EET>:[284]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Finished JobRunner: DefaultJobRunner-7, available threads in DefaultJobPool = 10, time spent = 8ms> <2011-01-12 14:00:03.521 EET>:[287]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, EVENT = CreatedSendingQueue, DEVICEPIN = 2100000a> <2011-01-12 14:00:03.526 EET>:[290]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, EVENT = Sending, TAG = 1288699908, DEVICEPIN = 2100000a, VERSION = 16, CONNECTIONID = -872546301, SEQUENCE = 0, TYPE = NOTIFY-REQUEST, CONNECTIONHANDLER = http, PROTOCOL = TCP, PARAMETERS = [MGONTAR/10.10.0.35:100], SIZE = 339> <2011-01-12 14:00:03.531 EET>:[291]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Number of active push connections:0> <2011-01-12 14:00:03.591 EET>:[292]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, EVENT = Notification, TAG = 1288699908, STATE = DELIVERED> <2011-01-12 14:00:03.600 EET>:[296]:<MDS-CS_MDS>:<DEBUG>:<LAYER = SCM, EVENT = Device connections: AVG latency (msecs)79> <2011-01-12 14:00:03.600 EET>:[297]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, Removed push connection:-872546301> <2011-01-12 14:00:07.015 EET>:[298]:<MDS-CS_MDS>:<DEBUG>:<LAYER = IPPP, EVENT = RemovedSendingQueue, DEVICEPIN = 2100000a> And here is real MDS log: <2011-01-12 11:35:02.763 GMT>:[3932]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, PapServlet: request from 192.168.1.241 583 bytes...> <2011-01-12 11:35:02.897 GMT>:[3933]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Mapping PAP request to push request for pushID:pushID:sdfsdfwerwer> <2011-01-12 11:35:02.909 GMT>:[3934]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, PushServlet: POST request from [UNKNOWN @ 192.168.1.241] to [PAPDEST=WAPPUSH%3D22D7F6BD%253A7874%2FTYPE%3DUSER%40rim.net&PORT=7874&REQUESTURI=/]> <2011-01-12 11:35:02.909 GMT>:[3934]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<push id: pushID:sdfsdfwerwer> <2011-01-12 11:35:02.910 GMT>:[3935]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, submitting push message with id:pushID:sdfsdfwerwer> <2011-01-12 11:35:02.910 GMT>:[3936]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Executing push submit command for pushID:pushID:sdfsdfwerwer> <2011-01-12 11:35:02.911 GMT>:[3937]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Pushing message to: 22d7f6bd> <2011-01-12 11:35:02.912 GMT>:[3938]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Number of active push connections:1> <2011-01-12 11:35:02.931 GMT>:[3939]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, added server-initiated connection = -1848311806, push id = pushID:sdfsdfwerwer> <2011-01-12 11:35:03.240 GMT>:[3940]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = IPPP, EVENT = CreatedSendingQueue, DEVICEPIN = 22d7f6bd, USERID = u3> <2011-01-12 11:35:03.241 GMT>:[3941]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = IPPP, EVENT = Sending, TAG = 536543251, DEVICEPIN = 22d7f6bd, USERID = u3, VERSION = 16, CONNECTIONID = -1848311806, SEQUENCE = 0, TYPE = NOTIFY-REQUEST, CONNECTIONHANDLER = http, PROTOCOL = TCP, PARAMETERS = [LDN-Server1/192.168.1.240:7874], SIZE = 383> <2011-01-12 11:35:03.241 GMT>:[3942]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Number of active push connections:0> <2011-01-12 11:35:03.253 GMT>:[3943]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SRP, SRPID = S27700165[LDN-SERVER1:3200], EVENT = Sending, VERSION = 1, COMMAND = SEND, TAG = 536543251, SIZE = 570> <2011-01-12 11:35:03.838 GMT>:[3944]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SRP, SRPID = S27700165[LDN-SERVER1:3200], EVENT = Receiving, VERSION = 1, COMMAND = STATUS, TAG = 536543251, SIZE = 10, STATE = DELIVERED> <2011-01-12 11:35:04.104 GMT>:[3945]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = IPPP, EVENT = Notification, TAG = 536543251, STATE = DELIVERED> <2011-01-12 11:35:04.121 GMT>:[3946]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Device connections: AVG latency (msecs)893> <2011-01-12 11:35:04.135 GMT>:[3947]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<INFO >:<LAYER = IPPP, DEVICEPIN = 22d7f6bd, DOMAINNAME = LDN-Server1/192.168.1.240, CONNECTION_TYPE = PUSH_CONN, ConnectionId = -1848311806, DURATION(ms) = 1151, MFH_KBytes = 0, MTH_KBytes = 0.374, MFH_PACKET_COUNT = 0, MTH_PACKET_COUNT = 1> <2011-01-12 11:35:04.144 GMT>:[3948]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = IPPP, Removed push connection:-1848311806> <2011-01-12 11:35:09.264 GMT>:[3949]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = IPPP, EVENT = RemovedSendingQueue, DEVICEPIN = 22d7f6bd, USERID = u3> <2011-01-12 11:35:58.187 GMT>:[3950]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SRP, SRPID = S27700165[LDN-SERVER1:3200], EVENT = Sending, VERSION = 1, COMMAND = INFO, SIZE = 46> <2011-01-12 11:35:58.187 GMT>:[3951]:<MDS-CS_LDN-SERVER1_MDS-CS_1>:<DEBUG>:<LAYER = SCM, Sent health to S27700165[LDN-SERVER1:3200] Health=[0x 0000 0007 0000 0000],Mask=[0x 0000 0007 0000 0000],Load=[60]> As you can see, logs not really differs, message is marked as delivered. But my app on device not really gets this message (as it works in mds simulator) Please advice me, what may be wrong? Is there some certificate to install or security settings I should configure to make this push message came to device application? Thank you! same question on bbforums

  Read the article

• Installing SQLServer 2005 on Windows 7 64bit

  - by Mostafa

  Hi , It's 3 days I'm trying to install SqlServer 2005 under Windows 7 64 bit on my computer. First let me tell you what I've done and what I've got till now . 1-I Installed Windows 7 64 Bit on my computer 2-I tried to install SQl Server 2005 "Developer Edition" 2.1 But in "System Configuration Check" Page i recieved 2 warning , One for "IIS Feature Requirement" and another for "ASP.NET Version Registration Rquired" . 2.1.1 . I installed "Internet Information Services" from "Turn Windows features on or off" section in control panel 2.1.2 I Enabled reporting service 32 bit from "Inetpub= AdminScripts = adsutil.vbs" 2.2 At this stage There was no waring in System Configuration Check 3- So I installed SQl Server 2005 Developer Edition By all default settings 4- I installed Sql Server 2005 Service Pack 3 64 bit Now when when i run "Management Studio" There is no name in "Server name" section . I typed my Computer name Or "." and i got this Error : A network -related instance-specific error occurred while establishinga connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (Provider: Named Pipes Provider , error :40 - Could not open a connection to SQL Server ) ( Microsoft SQL Server , Error :2) . I googled some for this Error and some people said follow this instruction: Startsql server 2005Configuration toolsSql Server Surface Configuration AreaSurface Area Configuration for services and Connections But i got this Error : No SQl SErver 2005 Components were found on the specified computer . Either no components are installed , or you are not a administrator on this computer (SQLSAC) I'm really tired because of that , and i don't know what's wrong with this . Some more information : I have no additonal software on my computer , like Antivirus or Proxy I tried all step with "Standard Edition" either , but no difference My user is Administrator I tried more than 5 times all those steps including re-installing Windows 7 . Please help me , I'm losing all my hair

  Read the article

• Browser sends http request with RANGE

  - by nute

  I have a local testing environment in a Fedora virtual machine. Strangely, resources (css and js files) don't seem to work. Looking at Firebug, I see that the browser sends the HTTP request with "Range bytes=0-". The server responds with either an empty 200OK or an empty 206 Partial Content. Here is an example: Response Headers Date Mon, 23 Nov 2009 23:33:26 GMT Server Apache/2.2.13 (Fedora) Last-Modified Thu, 19 Nov 2009 22:58:55 GMT Etag "18-3aec-478c14dbee138" Accept-Ranges bytes Content-Length 15084 Content-Range bytes 0-15083/15084 Connection close Content-Type text/css Request Headers Host fedora.test User-Agent Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.1.5) Gecko/20091105 Fedora/3.5.5-1.fc11 Firefox/3.5.5 Accept text/css,*/*;q=0.1 Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 300 Connection keep-alive Referer http://fedora.test/pictures/ Cookie __utma=26341546.1613992749.1258504422.1258569125.1258752550.4; __utmz=26341546.1258504422.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none); PHPSESSID=tqf8jfmc77qihe97rl4tmhq685 Range bytes=0- If-Range "18-3aec-478c14dbee138" I don't know if the browser is sending the wrong request, or if it's the server that is doing this. Request made to the outside (such as google analytics) are working fine. This is running in Fedora 11 in VirtualBox. Apache. PHP. The files are being served through the "shared folders" feature of VirtualBox (could it be related?). No error logs could help me.

  Read the article

• 301 redirect Rule For Load Balance F5 BigIp

  - by Kshah

  I have a load balancer F5 Big ip for my website. Currently, I am having 302 redirect in place; however, I wanted to apply 301 but dont know how. For example: My website (abc.com) when typed 302 redirects to abc.com/index and when typed www.abc.com 302 redirects www.abc.com/index. I wanted to have a rule which will help me in abc.com - 301 redirect - www.abc.com/index abc.com/index - 301 redirect - www.abc.com/index www.abc.com - 301 redirect - www.abc.com/index Below is the code that my tech person is trying: Redirect to WWW when HTTP_REQUEST { if { [HTTP::host] equals "abc.com" or [HTTP::host] equals "abc.co.in" or [HTTP::host] equals "www.abc.co.in" } { if {!( [HTTP::path] equals "/")} { HTTP::respond 301 Location "http://www.abc.com[HTTP::path]" } } } Redirect POST when HTTP_REQUEST { if { [HTTP::method] equals "POST" } { persist source_addr pool shop_shop_vr4_http } } Redirect-VR4 HOMEPAGE when HTTP_REQUEST { if { [HTTP::path] equals "/" or [HTTP::path] starts_with "/target/" or [HTTP::path] starts_with "/logs/" or [HTTP::path] starts_with "/config/" } { HTTP::redirect "http://[HTTP::host]/index.jsp.vr" } }

  Read the article

• Juniper router dropping pings to external interface

  - by Alexander Garden

  My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

  Read the article

• HAproxy - Redirect issue - Uri Variables ?

  - by Justin

  I'm using haproxy 1.5dev3 and I was wondering if there is any possible way to grab uri variables from a request to reappend the query on the end of a redirect url? What I'm trying to do is redirect from: http://www.domain.com/page/example.htm?id=1234567 to: http://www.domain.com/frame/newpage.cfm?id=1234567 redirect prefix doesn't work properly as it tries to append /page/example.htm to the end of the redirect url. Can I do some sort of rewrite to accomplish this? It would be awesome if you could use uri and queries as variables for redirection/pool selection like on F5. Please help...Thanks!

  Read the article

• Linksys WAP54G v3.1 no access, power and link LED solid

  - by user142113

  I'm managing the Network of a small enterprise. A Linksys WAP54G v3.1 used to provide the WiFi network. I was called, because the device did not provide a WiFi network anymore. I first of all tried to ping the device via LAN, but there was no reaction. I've frequently reconnected the AP to the mains and always the POWER and the LINK LED keep solid, even if no network cable is connected. What I've done yet: Reset as documented: Pressed the RESET button for 10 seconds. After that I have tried to access the AP with a direct cable connection to my computer, that I've set to a static ip of 192.168.1.240, but i got no ping response on the default IP 192.168.1.245. Furthermore ipconfig reports "media disconnected". More complex reset method as described here http://bruceshankle.blogspot.de/2005/12/how-to-reset-linksys-wap54g.html as well had no effect. also tried to ping 192.168.1.1 without success Tried this method: http://www.daniweb.com/hardware-and-software/networking/threads/142437/linksys-wireless-access-point-problem#post680245 but there was no ping response when powering up. As well the tftp transfer timed out Finally tried to short pin 15 and 16 of the flash chip on the bottom side of the AP mainboard while booting to provoke a Checksum error. This should lead to the possibility to upload a firmware with tftp, as the AP stops booting and waits for a tftp connection on 192.168.1.1. But I've had no success. As well i've put pin 15 and 16 to ground while booting, also without an effect. After all that I still can't ping the AP, ipconfig still tells me "media disconnected". The POWER and LINK LED are solid. I would appreciate your answers

  Read the article

• sorry, the maximum allowed clients from your host (10) are already connected" FTP error

  - by Sejanus

  Hello, I keep getting the "sorry, the maximum allowed clients from your host (10) are already connected" error whenever I try to transfer a large number of files. At first I thought it's a filezilla bug, however I get the same error basically with every FTP client I've tried, including Total Commander under Wine. I do not get that error using Windows. I did try to limit maximum allowed connections for Filezilla, both in server settings and in global settings, it didnt change anything. I did try to switch between passive and active modes (not sure if it's related at all, just last desperate attempt), and it didnt change anything either. When I try to use native ftp client (not sure how is it called, the one in Places - Connect to a server) I get abstract "connection refused" error every time I transfer large number of files. Connection is refused for separate particular files, if I click "Ignore" each time the rest of files are transfered perfectly well, so I assume it's the very same error. Anything I could do? This really drives me mad, transfering large numbers of files is a part of my everyday job... P.S. and this happens with many different FTP servers. Also I dont get this error in Windows. So I assume it's not a server problem. P.P.S. I am aware of similar question here, the answer provided just didn't solve it to me.

  Read the article

• What are the implications of expanding an internal subnet mask?

  - by Philip

  Our network is currently working on a 192.168.0.x subnet, all controlled through DHCP, except for the few main servers who have hard-configured IP address settings. What would I kill if I changed the DHCP-published subnet mask from 255.255.255.0 to 255.255.0.0? The reason for doing this is not because we have a huge sudden influx of machines, but because I'd like to start partitioning specific devices into specific IP ranges (to be neat and tidy). For what its worth, I don' plan on changing the allocated DHCP address range, but rather want to move some of the reserved and excluded DHCP addresses out of the address pool. e.g. printers will be 192.168.2.x I will obviously need to change the subnet mask manually on my manually configured devices.

  Read the article

• 1000Base-X layer 2/MAC address details

  - by user69971

  A layer 2 Ethernet frame is sent with a source and destination MAC address. Given a 100Base-TX (copper) trunk between two Cisco switches, I can do a "show interface fa 0/0" on S1 to see the MAC address assigned to the trunking interface, then go to Switch2 and do a "show mac address-table" and find the MAC address of the S1 fa 0/0 interface as a dynamically learned MAC in the table. Given a similar setup with a 1000Base-X (fiber GBIC) trunk, the MAC address shown in "show interface gi 0/0" on S1 does not show up in the MAC address-table of S2. Everything I can find online indicates that 1000Base-X uses largely the same layer 2 format as copper connections. There's some slight alterations - minimum frame size is slightly larger - but the fundamentals of the frame structure appear to be the same, including transmission with a source and destination L2 address. Why doesn't the address of gi 0/0 show up in the MAC address table of the connection switch? The only thing which seems to make sense would be that the GBIC has its own MAC address, almost as if its acting as a mini 2-port switch or hub, with the switch-assigned MAC address showing up on the interface connection and a different MAC address assigned to the fiber side. If this is the case, is there any way to see the GBIC MAC address on the switch? (I've tried to look up the details in IEEE 802.3z but it doesn't seem to be available without an IEEE membership or purchasing the standard. I find the base 802.3 PDFs for download, but not 802.3z.)

  Read the article

< Previous Page | 311 312 313 314 315 316 317 318 319 320 321 322  | Next Page >