Search Results

Search found 9634 results on 386 pages for 'proxy pattern'.

Page 319/386 | < Previous Page | 315 316 317 318 319 320 321 322 323 324 325 326  | Next Page >

• Can a USB/IDE/SATA adapter be flaky?

  - by Ward

  I use USB/IDE/SATA converters a lot and on the two that I have now, I sometimes get errors copying files to drives. It only happens when I'm copying big files to the drive (big can mean as little as 100MB, I think it happens more often with bigger files - 300MB or more), and basically the copy will fail and I'll get one or more error messages about "Delayed write failed." But if I disconnect the drive and re-connect it, I'll usually be able to continue. (The file that was being copied will be corrupt, but otherwise the drive is fine.) I just noticed a new type of flakiness: the data transfer rate can vary widely. I copied one set of files (5x300MB files) and it took 10+minutes, then I copied another set (approx. the same sizes) and it took less than a minute. I haven't done systematic testing, the other things I'm doing on my laptop at the same time might have some impact, and I haven't cross-checked the two adapters I have and the 3 hard drives I'm working with to see if there's a pattern. I'm more wondering if anyone else has seen anything like this.

  Read the article

• WAN Optimization for Small Office/Home Office

  - by TiernanO

  I have been reading up on WAN optimization for the last while, mostly out of interest of speeding up my own internet connections, but also to speed up the office internet connection. At home, I have 2 cable modems plugged into a RouterBoard RB750, which load balances the connections. In the office, we have a single connection into a NetGear router. Most of the WAN Optimization products I have seen, seem to be prohibitively expensive, but also seem to be based on the idea of having multiple branches around the world. What I am looking for, ideally, is as follows: software install: I am "guessing" I need to install it in 2 places: one in the office or house, and one in "the cloud". any connections going to, say, The US (we are in Europe, but our backup's live in the US currently, which would be something important to speed up) would be "tunnelled" though the Optimizer. If downloading or uploading large files, open multiple connections between both "the cloud" and the optimizer... This is where a lot of speed could be gained. finally, for items not compressed, they would be compressed on the cloud side of things, also items that are already on the optimizer could be not sent again. kind of like RSync or Proxy servers... So, is there something that can be done? Is it available using off the shelf components (some magic script with SSH, Squid, Linux and duct tape) or is it something that needs to be purchased? or even an Open Source Project that does 90% of what i am asking?

  Read the article

• What can I do with a home server?

  - by Joel Coehoorn

  I have an old 700 Mhz Pentium III at home running Windows 2000 Server, with a home router set up to pass incoming requests to it and a DynDNS account set up so it's easy to find. Right now I'm using it for a number of things: Shared folders + backup inside the home network Shared Printer inside the home network Domain Controller, just because I feel like it and because it's useful to me as practice to keep those "enterprise" administration skills. Web Server FTP remote access for my files. I abandoned this for security reasons, but it's still worth leaving visible. Remote Desktop in to the home network (thinking about adding VPN service) SVN repository MySQL - Will be moving to SQL Server 2008 Standard soon. After I upgrade my wife's laptop from home to pro later this year it will also become a domain controller It's the only place I still have access to Internet Explorer 6 any more without setting up a new virtual machine, so I use it for testing code with that browser. The question is: What else could I be doing with this machine? Update Additional ideas based on the suggestions: Media Server/DVR Build server PBX SSH Proxy Server Continuous Integration Server Personal OpenID Provider Update2 Just a note that this server was recently upgraded to an Atom330 with 2 GB ram and bigger hard drive. For all that's slow for a "modern" cpu, it should still be much faster than the old Pentium III and the expected power savings should make the upgrade essentially free over the course of the next year or two. Also, it's now running Windows Server 2008.

  Read the article

• How to simulate Apache [END] flag on a redirect?

  - by Javier Méndez

  For business-specific reasons I created the following rewrite rule for Apache 2.2.22 (mod_rewrite): RewriteRule /site/(\d+)/([^/]+)\.html /site/$2/$1 [R=301,L] Which if given an URL like: http://www.mydomain.com/site/0999/document.html Is translated to: http://www.mydomain.com/site/document/0999.html That's the expected scenario. However, there are documents which name are only numbers. So consider the following case: http://www.mydomain.com/site/0055/0666.html Gets translated to: http://www.mydomain.com/site/0666/0055.html Which also matches my rewrite rule pattern, so I end up with "The web page resulted in too many redirects" errors from browsers. I have researched for a long time, and haven't found "good" solutions. Things I tried: Use the [END] flag. Unfortunately is not available on my Apache version nor it works with redirects. Use %{ENV:REDIRECT_STATUS} on a RewriteCond clause to end the rewrite process (L). For some reason %{ENV:REDIRECT_STATUS} is empty all the times I tried. Add a response header with the Header clause if my rule matches and then check for that header (see: here for details). Seems that a) REDIRECT_addHeader is empty b) headers are can't be set on the 301 response explicitly. There is another alternative. I could set a query parameter to the redirect URL which indicates it comes from a redirect, but I don't like that solution as it seems to hacky. Is there a way to do exactly what the [END] flag does but in older Apache versions? Such as mine 2.2.22. Thanks!

  Read the article

• Change source address based on destination IP

  - by hgj

  We have several "router" machines that gather a lot of external IP addresses on the same host and redirect, NAT or proxy the traffic to the internal network. They also act as routers for the machines on the internal network. This works fine, however I am unable to make the routing table, so I can change the source address, based on the destination a machine from the internal network want to access. Let's say I have a router, that has public addresses P1 (5.5.5.1/24) and P2 (5.5.5.2/24). All traffic goes through P1, but if necessary, the host is reachable on P2 too. This looks like this and works fine: > ip addr ... 1: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether aa:bb:cc:dd:ee:11 brd ff:ff:ff:ff:ff:ff inet 5.5.5.1/24 brd 5.5.5.255 scope global eth1 inet 5.5.5.2/24 brd 5.5.5.255 scope global secondary eth1:p2 ... Now I want to use P2 as the source address, if I want to access the Google DNS service for example (8.8.8.8). So I add a row in the routing table like: > ip route add 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 > ip route ... default via 5.5.5.254 dev eth1 5.5.5.0/24 dev eth1 proto kernel scope link src 5.5.5.1 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 ... But this does not work. If I ping 8.8.8.8, the host still uses P1 as the source address, and does not use P2 at all for outgoing connections. Am I doing it right? I guess not...

  Read the article

• Can't reliably ping 6224 router from directly-attached system

  - by David Mackintosh

  OK, here's my situation. This is on the internet. The 6224 is the router in this picture and physically resides in Kanata. Both VLAN 1697 and 3994 are provided by an internet service provider. These VLANs are provided through a single 1Gb ethernet wire. The Kanata hosts are directly attached to the 6224; the other two sites are remote. VLAN 3994 is a single IP address space, so theoretically it shouldn't matter physically where the hosts on that subnet are. Here's the problem. I have a monitoring system which is connected further into the internet, so probes from the monitor would come in to this diagram on the 1697 VLAN. When I ping hosts at Albert or Bells Corners from the internet, there is 0 loss. The connection looks perfect. When I ping hosts at Kanata, I lose anywhere from 10 to 40% of the pings. The loss is not predictable, but: when I do lose them, I always lose at least 3, usually 4, rarely more, pings in a bunch. I have attached a monitor directly to the 6224 in Kanata on 3994.. When the monitor pings the 6224 routing interface, I see exactly the same loss pattern -- but NOT at the same time as the loss from the remote system. Ping time is around 1ms. When the monitor pings another system directly attached to the 6224, there is 0 loss. Ping time is about 0.1ms, one-tenth of the time to ping the router. Anyone know what is going on here?

  Read the article

• Apache suddenly very slow on http and faster on https

  - by hsnm

  Background: I have Apache 2 running on ubuntu. There is a low usage on it and mostly being accessed for a web service URL from mobile apps. It was working fine until I installed SSL certificates. I now have both http and https. When I access the server using https, I get a fairly quick response (but probably not as fast as before). When I use http, it's so slow. What I tried: From this post: I curl localhost from the host and it takes some time, meaning there is no routing issue. The server runs on Amazon EC2 instance and is managed by me only. Also: I see that Apache once running, creates the maximum number of processes it is allowed to, which was not the case before. I lowered the MaxClients to 20 and I think I'm getting faster responses but it still takes over a minute and I always have MaxClients Apache processes. dmesg returns many [ 1953.655703] TCP: Possible SYN flooding on port 80. Sending cookies. When I netstat I get many entries with SYN_RECV. Possibly a DDoS attack? From EC2's monitoring diagrams I see a pattern of high "Maximum Network In (Bytes)" since 2 days ago. By the way the server is still being tested, the actual traffic is very low and not consistent. I tried to go with this solution to limit incoming connections using iptables, still no luck, but I'm trying. Question: What could be the problem? Is this a DDoS attack?

  Read the article

• Xen virtual host can reach some sites but not others

  - by Tun H S Lee

  Okay, this is killing me. Debian Squeeze, Xen 4.0, brand new install. No iptables rules whatsoever except for the ones added by the default xen bridge script. Dom0 can reach the entire world, no problems. DomU can receive packets from some hosts, but not from others. For instance, if I ping Host A, it works fine. If I ping Host B, the DomU reports 100% packet loss. The hosts are random, but consistent (even after reboots). I can see no pattern to why some work and others don't. In fact, in some cases, different virtual hosts on the same server (an other server at a different data center) are divided; some work and others do not. I can reboot (DomU or Dom0 too) and the same hosts will work or fail as before. If I tcpdump on the Host B while pinging from the DomU, everything looks fine. It sees the echo request coming in and says it's sending one back. However, if I tcpdump peth0 on the Dom0, it never sees the echo reply. Any ideas what could be happening? I'm tearing my hair out here.

  Read the article

• Coldfusion:-Firefox can't establish a connection to the server at localhost

  - by Fransis

  I installed Coldfusion 8 trial version on my system (XP Professional sp3). I created an Folder in the “C:/Coldfusion8/wwwroot” called “buildProject” containing an Index.cfm and some other .cfm files. But I am unable to access the Neither my project files or CFIDE/Administrator I tried the following URLS http://localhost:8500/wwwroot/buildProject/ http://localhost:8500/CFIDE/administrator/index.cfm http:// 127.0.0.1:8500/wwwroot/buildProject/ http:// 127.0.0.1:8500/CFIDE/administrator/index.cfm http://localhost /wwwroot/buildProject/index.cfm http://localhost /CFIDE/administrator/index.cfm http://localhost /wwwroot/buildProject/ http://localhost /CFIDE/administrator/index.cfm Firefox can't establish a connection to the server at 127.0.0.1:8500. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. • I cleared the browsing “History” from both IE and FF. • I have restarted the CF server in the Control Panel Administrative Tools Services • Even restarted the IIS Getting the same error. Further I was trying to access IE/FF via CFbuilder But still I am getting the error “The connection was refused when attempting to contact [URL].” My inetpub is in the D rive where as CF8 is in C drive Also when i check IIS-5 Control Panel Admin tools Services I do not find the Localhost under web sites or FTP sites. Kindly help me with a fix.

  Read the article

• nginx with fail2ban and mod_security

  - by Mahesh

  I forgot to update my fail2ban config for nginx. I just moved to nginx from apache. Today, I got a lot of cals from a single IP. IP tried to access login pages with post and get methods IP tried to use nginx as a proxy (GET http:/...) IP searched images, js, css folders IP tried to inject -d url_allow_fopen =1 and something similar. Most of the calls ended with 404. http { limit_req_zone $binary_remote_addr zone=app:10m rate=5r/s; ... server { ... location / { limit_req zone=app burst=50; } I got approximately 50 requests from that ip for a second. So i updated my nginx like the above. Will it avoid too many connections per second now? I have updated my fail2ban jail.local to support nginx. I am confused with the nginx-noscript.conf [Definition] failregex = ^<HOST> -.*GET.*(\.php|\.asp|\.exe|\.pl|\.cgi|\scgi) ignoreregex = I am serving php with nginx. I checked apache's noscript.conf and which has .php extension on it too. I tested this above settings before restarting fail2ban and got thousands of ips matched. I removed php and nothing matched. Do i need .php| in nginx-noscript.conf? Using mod_security and fail2ban together bring any problem? When i was searching today, i came to know mod_security is available for nginx too. So i am planning to use it too.

  Read the article

• Hybrid Exchange Online setup with on premise public folders, certificate issues?

  - by exxoid

  We have a Hybrid Exchange setup with Exchange Online (v15 tenant) and Exchange 2010 on premise. The hybrid configuration for the most part is working, what I am having an issue with is getting public folders to work for cloud users. I followed the official documentation here (http://technet.microsoft.com/en-us/library/dn249373(v=exchg.150).aspx) and it kind of works. When I am accessing Outlook on a public wifi I am able to bring up the cloud mailboxes and on premise public folders show up in Outlook. When I am accessing email via Outlook as a cloud user on the same LAN as the on premise exchange, the cloud user makes the outlook.com connection for live/ad/archive mailbox but fails to create a proxy connection for the on premise public folders. The error I get is a certificate mismatch, it seems that when a user on the LAN accesses Outlook/Exchange it is using a different certificate vs. when Outlook is launched on a WiFi network. When I look at the Outlook connection information, I see the connection to outlook.com for ad/live/archive mailbox but no entry for public folder connection. Our on premise Exchange is 2010 SP3 with latest CUs. The client is a domain joined laptop with Windows 7 and Office 2010 SP2, latest windows updates applied. Our infrastructure has a working ADFS 3 and DirSync setup for Office 365. My question then is, what do I need to do to make sure that the Cloud user launching Outlook on the LAN uses the proper certificate (the wildcard 3rd party cert.. vs. the self signed certificate which it looks like it may be using during the connection attempt).

  Read the article

• Computer randomly shuts itself off

  - by Decency

  I have not been able to determine a pattern for why this happens, despite my best efforts. I've attempted to run it on full power with Prime95 and this doesn't trigger a restart. Generally the restarts occur while I'm playing games, watching videos, or even just having multiple tabs open in a browser. However, I often play processor intense games for hours without any restarts occurring, and sometimes they'll happen 3-4 times in an hour during less intense activity, so I don't think that is the problem. I imagine it has something to do with overheating or power consumption so I've been monitoring CPU temperature and cleaning with compressed air, but the problem keeps happening. I don't know how to track power consumption, and assume that this is the problem. Whenever this occurs, the sound gets stuck in a short loop of whatever was playing at the time, though restarts also occur when nothing is playing. Here is a screenshot of temperatures: and under load: Here's the parts list: http://secure.newegg.com/WishList/PublicWishDetail.aspx?WishListNumber=10546754 As shown in the list, the case includes a 585W Power Supply, which I've been told should be plenty. I built the computer myself with a friend's guidance but it's very possible I did something wrong. Right now I'm looking into ensuring that I have the latest drivers for all components. Any help would be appreciated- thanks.

  Read the article

• Do I need a helper column, or can I do this with a formula?

  - by dwwilson66

  I am using this formula =IF((LEFT($B26,2)="<p"),0,IF($B26="",0,IF($F26<>"",0,(FIND("""../",$B26))))) To parse data similar to the following. <nobr>&nbsp;&nbsp;&nbsp;&nbsp;contractor information</nobr><br> &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<a href="../City_Electrical_Inspectors.htm"><b> City Electrical Inspectors</b></a><br> <nobr>&nbsp;&nbsp;&nbsp;&nbsp;<a href="../City_Electrical_Inspectors.htm"><b>inspection</b></a></nobr><br> My problem comes in cases such as the first line, in which the line is not a new paragraph nor a link, and my FIND returns an error of #VALUE! Id like to create an IF test to scan the line for the existence of the pattern in my FIND statement before processing that statement. I figured that looking for an error condition may be the way to go. However, the only way I can envision this is as a self-referential formula, similart to the following pseudocode. IF(ISERROR($L26)=TRUE,$L26=0,L$26=the-result-of-the-formula-above) Can this be done with a formula or do I need to use a new helper column? Thanks.

  Read the article

• How do I tell Websphere 7 about a front end load balancer so that re-directs are handled correctly?

  - by TiGz

  On WebLogic 11G I can use the console to set the FrontendHost and FrondendPort on a server or on a cluster so that re-directs are handled correctly and end up resolving to the front end load balancer instead of the local host. The MBeans associated with this on WebLogic are, for example: MBean Name com.bea:Name=AdminServer,Type=WebServer,Server=AdminServer Attribute Name FrontendHost Description The name of the host to which all redirected URLs will be sent. If specified, WebLogic Server will use this value rather than the one in the HOST header. Sets the HTTP frontendHost Provides a method to ensure that the webapp will always have the correct HOST information, even when the request is coming through a firewall or a proxy. If this parameter is configured, the HOST header will be ignored and the information in this parameter will be used in its place. Type java.lang.String Readable / Writable RW How is the same thing achieved under Websphere 7? Follow up info: So I have 2 use cases actually. One is that I have a web app running under WebSphere on host A on port 9002 and a LB running on host B at port 80, when I visit the home page of the app via the LB on http://hostb/app the app redirects my browser to http://hostb:9002/app and it 404's I think this is WebSphere's fault but I guess it could be the app's fault? The second is that the web app in question needs to send emails containing URls that the customer can click on to get back into the web app - obviously this needs to be via the LB. On WebLogic the app uses MBeans to derive the LB url and I was hoping to use a similar mechanism on WebSphere.

  Read the article

• Cannot connect to MySQL on RDS (Amazon Web Services) from my laptop

  - by Bruno Reis

  I'm having some trouble connecting to a MySQL 5.1 server on an RDS instance on AWS from my laptop. The detailed description of the problem is here: https://forums.aws.amazon.com/thread.jspa?messageID=323397 In short: I have 2 MySQL servers, both with the same db configuration and firewall (security group) configuration. One of them works fine: I can connect to it from my EC2 instances (ie, from inside the AWS cloud) and from my laptop. The other one doesn't: I can connect from my EC2 instances but not from my laptop. The symptom: a connection attempt from my laptop just hangs, and then times out, as if there was a firewall blocking me (ie, silently dropping my SYN packets). I must say that everything has been working fine for a very long time, and this problem began suddenly, 3 days ago, without any modifications to DB parameters or the security groups. My current analysis of the situation: The firewall (ie, security group) cannot be the problem: both MySQL servers share the same firewall configuration -- I can connect to one of them but not to the other. Later on, I even added a rule to allow inbound connections from 0.0.0.0/0 (ie, I turned off the firewall), and nothing. Oh, I also created a new, fresh security group and changed this instance's SG to the new one (to which I first added my ip address, and then 0.0.0.0/0) but still nothing. The credentials cannot be the problem: I use the same from my laptop and from my EC2 instances -- and the user (which is what Amazon calls master user), in the database, has a host of '%'. MySQL is not blocking my IP due to, say, too many failed connection attemps: I've FLUSH HOSTS on the database, and also I tried to connect using many different source IP addresses, even from all around the world through a VPN proxy service. What could I be missing? I'm asking here because it's been about 36 hours since I've posted on AWS forums but got no answer at all over there... someone here might have a solution! Any input is really appreciated, I'm out of ideas. Thanks!

  Read the article

• Nginx , Apache , Mysql , Memcache with server 4G ram. How optimize to enought memory?

  - by TomSawyer

  i have 1 dedicated server with Nginx proxy for Apache. Memcache, mysql, 4G Ram. These day, my visitor on my site wasn't increased, but my server get overload always in some specified time. (9AM - 15PM) Ram in use is increased second by second to full. that's moment, my server will get overload. i have to kill all apache , mysql service and reboot it to get free memory. that's the circle. here is my ram in use at the moment 160(nginx) 220(apache) 512(memcache) 924(mysql) here's process number 4(nginx) 14(apache) 5(memcache) 20(mysql) and here's my my.cnf config. someone can help me to optimize it? [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql skip-locking skip-networking skip-name-resolve # enable log-slow-queries log-slow-queries = /var/log/mysql-slow-queries.log long_query_time=3 max_connections=200 wait_timeout=64 connect_timeout = 10 interactive_timeout = 25 thread_stack = 512K max_allowed_packet=16M table_cache=1500 read_buffer_size=4M join_buffer_size=4M sort_buffer_size=4M read_rnd_buffer_size = 4M max_heap_table_size=256M tmp_table_size=256M thread_cache=256 query_cache_type=1 query_cache_limit=4M query_cache_size=16M thread_concurrency=8 myisam_sort_buffer_size=128M # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 [mysqldump] quick max_allowed_packet=16M [mysql] no-auto-rehash [isamchk] key_buffer=256M sort_buffer=256M read_buffer=64M write_buffer=64M [myisamchk] key_buffer=256M sort_buffer=256M read_buffer=64M write_buffer=64M [mysqlhotcopy] interactive-timeout [mysql.server] user=mysql basedir=/var/lib [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid

  Read the article

• Javascript loading never completes on many sites

  - by Joe

  I recently moved country and have found that on many websites the page never finishes loading. In some cases, no content is ever displayed, but the loading will never time out. Loading Developer Tools in Chrome shows me that it is the Javascript files which never load. For example, this BBC article will never load compatability.js, though will load all the other JS files perfectly. Google Maps often fails to finish loading, meaning it's impossible to make searches. There seems to be no pattern to which files will fail to load (i.e. they don't come from the same CDN). I have tried Chrome, Safari and Firefox on OSX 10.8, and Chrome on my girlfriend's OSX 10.7. I have similar issues on the iPad. In many cases, if I can go to the mobile version of the page that seems to load fine. I have run the browsers in private mode, disabled plugins, updated flash, cleared the cache, flushed the DNS cache - though it would seem that if this is happening on other devices, none of this would work anyway. Is this an ISP issue? And if so, why would it be limited to certain JS files and not all? JS files from the same domain work fine, so I'm not really sure what I should be looking for.

  Read the article

• Scheduled Task unable to create/update any files

  - by East of Nowhere

  I have several tasks in Task Scheduler in Windows Server 2008 SP2 (32-bit) and they all successfully "do their work", except for creating or updating any files on Windows. All the tasks point to simple .cmd files that have the real work but beyond that there's no pattern: some call robocopy with the /LOG option, some call .exe files I wrote that manipulate XML files, some just do stuff with > redirection. With all of them, if I double-click the .cmd file myself, it works fine and the files are created or updated or whatever. If I run it from Task Scheduler (by the schedule or just clicking Run), the task always completes "successfully" but without any of the desired changes to files. I don't see any "unable to create file" errors in Event Viewer either. The tasks do all Run As a specific account, but I have logged in as that account and verified that it has permissions to do everything it needs to. Further details -- Task is set to Run whether user is logged in or not. Configured for: "Windows Vista or Windows Server 2008", there is no other Configured for option available.

  Read the article

• Debugging nginx URL rewrite: How do I figure out where the problem is?

  - by pjmorse

  I have a specific URL pattern on a site which needs to be redirected to the HTTPS version. This is a Django site; Nginx checks each URL in memcached, and if it doesn't find a cached version it proxies the request to Apache/mod_python for Django to render the page. The relevant configuration block is rewrite ^/certificate https://mysite.com/certificate ; rewrite ^/([a-zA-Z]{2})/certificate https://mysite.com/certificate ; ...and it doesn't appear to be working at all. Nginx is: $ nginx -V nginx version: nginx/0.7.65 built by gcc 4.2.4 (Ubuntu 4.2.4-1ubuntu4) TLS SNI support disabled configure arguments: --prefix=/usr/local/nginx --pid-path=/var/run/nginx.pid --with-http_gzip_static_module --with-http_ssl_module How can I figure out if the problem is my patterns not matching, or a more obscure configuration problem? (The site is localized to three languages, and the localization is in the URL string, e.g. /US/news/, /DE/about, etc. It tracks localization in the session as well, defaulting to US, so if you just requested /news Django will rewrite to /US/news unless the user has a cookie indicating they're using a different localization. Django handles this, though, not Nginx.)

  Read the article

• Connecting to a subdomain severs the connection to the domain itself. What's going on?

  - by TheAgent

  Hi all. We have a website on a third-party server (server leased and shared with other websites) and the server provides access to our SQL Server database through a subdomain in the form of mssql.DomainName.com. I was told to use SQL Management Studio Express to connect to this subdomain in order to manage the database. After a few tries and getting many "Timeout" messages, I finally manage to connect to the server; everything's fine. But now I can't connect to DomainName.com anymore. Trying to browse DomainName.com using Firefox, it tries to "lookup" DomainName.com address and fails, telling me "the server was not found". I have to disconnect Management Studio from the server and wait a couple of hour for DomainName.com to become available again, and after that, trying to reconnect to the SQL Server again repeats the scenario. While I can't browse DomainName.com directly, I can use a proxy to connect to it, meaning that the problem is somehow related to a DNS my computer tries to ask to translate the name to the corresponding IP. Anyone seen anything like this before? Any ideas? Thanks in advance.

  Read the article

• System With Two Network Adapters [closed]

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

• Adding a prefix or postfix to a Word 2013 quotation source

  - by user2690527

  I am using the German version of Word 2013, so I am not absolutely sure, if "quotation source" is the term being used in the English version. I am talking about the automatic text field, one can get via "References" (German: "Verweise"), "Insert quotation" (German: "Zitat einfügen"). Then one gets a drop down menu with all the entries from the biobliography, one can pick one and then an automatic text field is inserted into the text. After it is hopefully clear what I am talking about, here is the question: I choosed the citation style "ISO 690" that generates labels of the pattern "(author+year)" in round parentheses. Sometimes I have to append a prefix or postfix to the label, but this prefix/postfix must go into the parantheses. Is there any way how I can do this? For example, I can add page numbers to the end of a quotation label via a special dialog box that appears after a right click onto the text field and choosing "Edit quote" (German: "Zitat bearbeiten"). But there are a lot more cases of optional pre-/postfixes than page numbers. I am looking for a way to add general pre-/postfixes.

  Read the article

• Why is my computer randomly restarting? How can I fix it?

  - by kinglime

  I have a custom built desktop computer that I've been using since about a year ago. The main specs are: ASUS P8Z68-V LE Motherboard Intel Core i7 2600k Corsair Vengeance 16GB Ram ASUS ENGTX570 GPU Corsair TX650M PSU I was running an overclock of 4.4ghz for my cpu (I have a Hyper212 EVO) and 1600mhz for my RAM but have it currently turned off due to my issues. I am also currently running Windows 8 but this problem occured in Windows 7 too. Basically my issue is that seemingly randomly, with no pattern my PC will reset itself and ASUS Anti-Surge will alert me that something went wrong. This issue is not related to system stress. I can run it fine for an hour maxxed out on Prime95 then later I can be watching a mere YouTube video when it will randomly reset. This has been occurring probably for the last two weeks and it seems to be getting worse. I believe this might be related to the power supply but when I monitor it in the bios and in Windows it appears to be putting out the proper voltages. Also possibly related or not but my Nvidia drivers frequently temporarily fail and then warn me of some kind of kernel error? If I have to buy a new power supply that is what I'll do but I want to make damn sure that's the only issue at hand. Thank you everyone in advance, please help me diagnose the issue and tell me what I can do to fix it. If you need any additional info about my setup please ask me.

  Read the article

• TCP/UDP hole punching from and to the same NAT network

  - by Luc

  I was wondering if tcp/udp hole punching would still work when you are in the same network (behind a NAT), and what the packet's path would be. What happens when using hole punching on the same network, is that it will send a packet out with the same destination and source address. Only the source and destination port would differ. I imagine a router with NAT loopback enabled will handle this as it should, but how about other routers? Would they drop the packet, or would a router (the first?) from the ISP bounce the packet back after which it gets handled okay? I'm wondering because I was thinking about using this technique to circumvent a block between peers in a network (like a school network where clients can only access the internet, but any contact with each other is blocked). The only other option is to use a man in the middle as proxy (tunnel?). The disadvantage of this is that you have to have a server with significantly more bandwidth than one that would only do hole punching. Also the latency would increase significantly.

  Read the article

• Cannot make bind9 forward DNS query to subdomain unless recursive enabled

  - by PP.

  I am trying to develop my own dynamic DNS. I'm running my own custom DNS for the subdomain on port 5353. ASCII diagram: INET --->:53 Bind 9 --->:5353 node.js | V zone_files I have example.com. The node.js DNS is for dyn.example.com. In my /etc/bind/named.conf.local I have: zone "example.com" { type master; file "/etc/bind/db.com.example"; allow-transfer { zonetxfrsafe; }; }; zone "dyn.example.com" IN { # DYNAMIC type forward; forwarders { 127.0.0.1 port 5353; }; forward only; }; I've even gone so far as to add a NS in my example.com zone file: $TTL 86400 @ IN SOA ns.example.com. hostmaster.example.com. ( 2013070104 ; Serial 7200 ; Refresh 1200 ; Retry 2419200 ; Expire 86400 ) ; Negative Cache TTL ; NS ns ; inet of our nameserver ns A 1.2.3.4 ; NS record for subdomain dyn NS ns When I attempt to get a record from the subdomain server it doesn't get forwarded: dig @127.0.0.1 test.dyn.example.com However if I turn recursive on in /etc/bind/named.conf.options: options { recursion yes; } .. then I CAN see the request going to the subdomain server. But I don't want recursion yes; in my Bind configuration as it is poor security practice (and allows all-and-sundry requests that are not related to my managed zones). How does one forward (proxy) zone queries for just one zone? Or do I give up on Bind altogether and find a DNS server that can actually forward specific queries?

  Read the article

< Previous Page | 315 316 317 318 319 320 321 322 323 324 325 326  | Next Page >