Search Results

Search found 10211 results on 409 pages for 'adf controller'.

Page 337/409 | < Previous Page | 333 334 335 336 337 338 339 340 341 342 343 344  | Next Page >

• 0x0000007b WinXP in VirtualBox with no Admin access on source drive

  - by Ozzah

  I have a physical drive with an installation of WinXP-32 which I have made a clone of using SysInternals disk2vhd. I have no admin rights on this installation. I have tried to boot this VHD in VirtualBox, however it blue screens on 0x0000007b. I have researched this and apparently the cause is that Windows doesn't like the IDE controller changing. I have tried all the available controllers in VirtualBox, but they all produce the same result. There is a Microsoft KB article which describes a method involving loading a .reg file and extracting some sys files from a CAB. This method apparently works well for many people with this problem, however it will not work for me as I don't have admin rights on the WinXP installation. Is there anything I can do in this case? Is there any way of loading the .reg file outside the OS? or perhaps doing a repair using the WinXP CD? Even though I have no admin rights on the source drive installation of Windows, I do obviously have full access to the file system directly on the drive and also in the VHD itself.

  Read the article

• Experience with AMCC 3ware 9650se raid cards? Ours seems dead

  - by antiduh

  We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated. Edit: These are the kernel errors we see: 3ware 9000 Storage Controller device driver for Linux v2.26.02.012. 3w-9xxx 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 3w-9xxx 0000:09:00.0: setting latency timer to 64 3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing. 3w-9xxx: scsi0: ERROR: (0x06:0x001F): Microcontroller not ready during reset sequence. 3w-9xxx: scsi0: ERROR: (0x06:0x0036): Response queue (large) empty failed during reset sequence. 3w-9xxx 0000:09:00.0: PCI INT A disabled

  Read the article

• Oracle with Kerberos authentication and Windows 2003 Server as KDC

  - by Supaplex

  I am running Oracle 10.2 on a Windows 2003 Server SP2 which is also the domain controller on the network. I wish to switch authentication method from NTS to Kerberos. I have spent a lot of time trying to configure Oracle with Kerberos authentication from the Oracle Advanced Security option from the Net Manager utility. I have disabled NTS so Kerberos is promoted as the preferred authentication method. But as soon as the configuration is saved from Net Manager and I restart the Oracle server service, Oracle will not start. I don't know what Oracle is complaining about, because I don't know where to look for the Oracle error log. My first question is: how can I figure out what's bugging Oracle? My second question: is there a good tutorial for setting up Oracle on a Windows 2003 with Kerberos Authentication, where the Windows 2003 Server is the KDC? Maybe there is a book I can get? I have read Oracles own guide, but it is mostly for Linux/Unix. Thanks a lot!

  Read the article

• Xbox360 Universal Media Remote - out of sync?

  - by Traveling Tech Guy

  Hi, I have the Universal Media Remote from Microsoft, which was included with my HD-DVD package. I've been using it for over a year to watch videos/DVDs on my Xbox360 and it saved me the hassle of navigating with the game controller (which turns itself off every 5 minutes).All of a sudden (it didn't fall or suffer any severe trauma), it does not communicate with the Xbox anymore: it is on, I replaced batteries several times, but the Xbox does not respond to commands. The TV does - volume, channels, etc. - but I need the Xbox functionality.As far as I can see, there's no way to sync the remote with the Xbox - it lacks that small sync button that the game controllers have.I called Microsoft Support and spoke for an hour to someone who, I guess didn't know what to do at all. Bottom line - since it's been over a year, they won't fix/replace it - I have to get a new one.Before I do (if I do), I need to know if there's anything I can do with the existing remote, and will I have the same problem with a new one (i.e. the problem is with the Xbox itself)? Thanks!

  Read the article

• Data Protection Manager System Protection Backups Failing

  - by TrueDuality

  I'm just starting to setup DPM 2010 in a test environment with a Domain Controller and a File Server. Everything seem to be working fairly well and I can get all of my backup jobs to succeed except for the "Computer\System Protection" backups. Both servers are running fully up to date 64 bit Windows Server 2008 R2 Enterprise with Service Pack 1. The error that is being provided is: DPM cannot create a backup because Windows Server Backup (WSB) on the protected computer encountered an error (WSB Event ID: 517, WSB Error Code: 0x8078001D). (ID 30229 Details: Internal error code: 0x809909FB) This Microsoft Knowledge Base article describes the issue perfectly and provides a hotfix. I downloaded the hotfix, moved it onto the affected server, attempt to run it and receive the following error: The update is not applicable to your computer. I've verified that I have indeed downloaded the 64 bit version. According to this thread the hotfix got rolled into Service Pack 1, yet I'm still experiencing the issue. Both machines do have the Windows Server Backup feature installed. Can anybody point me in the right direction? What am I missing?

  Read the article

• netlogon errors

  - by rorr

  I have two instances of mssql 2005 and am using CA XOSoft replication. The master is a failover cluster and the replica is a standalone server. They are all running Server 2003 sp2 x64. Same patch levels on all servers. This setup has worked great for several months until we recently restricted the RPC ports on both nodes of the master(5000 - 6000 using rpccfg.exe). We have to implement egress filtering, thus the limiting of the ports. We began receiving login errors for sql windows authentication and NETLOGON Event ID: 5719: This computer was not able to set up a secure session with a domain controller in domain due to the following: Not enough storage is available to process this command. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. We also see group policies failing to update and cluster file shares go offline at the same time. The RPC ports were set back to default when we started seeing these problems and the servers rebooted, but the problems persist. The domain controllers are not showing any errors. Running dcdiag and netdiag shows everything is fine. We have noticed that the XOSoft service ws_rep.exe is using a lot of handles(8 - 9k), about the same number that sqlserver is using. As soon as xosoft replication is stopped the login errors cease and everything functions correctly. I have opened a ticket with CA for XOSoft, but I'm not sure that the problem is actually xosoft, but that it is the one bringing the problem to light. I'm looking for tips on debugging RPC problems. Specifically on limiting the ports and then reverting the changes.

  Read the article

• Can't connect two PCs to a Network Switch at the same time (Windows 7)

  - by puk

  I have two computers connected to a network switch and every once in a while one of the computers will lose its internet connection. It's almost always the same computer every time. However, if I play around with the control panel, I can switch it, so that now the other computer is not connected. Restarting either of the computers does not help either. In Windows, the worlds-greatest-trouble-shooter tells me that a network cable is unplugged and that I should try plugging it in...Disabling and re-enabling my NIC does not fix this problem, neither does swapping cables around. When rebooting, the BIOS complains about how the Ethernet Cable is not plugged in. If it's in any way important, My set up at the office is like so: Modem - Routher - Network Switch 1 - Network Switch 2. I have tried turning off the energy saving option for my NIC, and I tried manually setting the link-speed to 100Mbps Full Duplex without any luck. Also, I have a Realtek PCIe GBE Family controller on both computers Does anyone have any idea why this is happening every 5-10 days? EDIT: I have also tried using a completely different Network Switch and the problem still persists as before.

  Read the article

• How to connect the virtual networks of vmware guests running on different hosts?

  - by gyrolf

  In a test setup, we are running several virtual machines on a single vmware workstation host. All virtual machines are connected via a "host only" network. This runs fine up to 2 or 3 virtual machines (depending on the host hardware). To allow more virtual machines, we want to use more host machines. Details about the environment and applications: Host PCs are running Windows XP in a corporate intranet. VMware used is Workstation 6.5 Guests are running Windows Server 2003 All guests act as Web Servers One of the guests additionally acts as Windows File server, offering shared folders for the other guests to connect to. Restrictions: VMware guests shall not be visible from the intranet. Changes to the host PC are restricted by corporate policy. In the virtual network, no domain controller exists. All virtual machines are member of the same workgroup. Running the virtual network as NAT is possible. Port forwarding might be used if it does not conflict with ports used by the host PC. Looking for a solution, I found hints about using router or vpn software on the hosts, but without any details how to setup. (I found a similar question Sharing the network between 2 VMware hosts, but the answer was not sufficient for me.)

  Read the article

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• WS2008 NTP - Using time.windows.com,0x9 - Time always skewed forwards

  - by David

  I have a domain controller configured to use time.windows.com (with 0x09 flags set). I've noticed that frequently the systems' clock is fast - it varies from 10 minutes to even 45 minutes. I always have to keep resetting the system date/time back to what it should be. When I run "w32tm /query /source" it tells me it's using time.windows.com, and obviously I trust Microsoft not to serve incorrect times, but why is my server's clock fast? EDIT: There are a few Time-Service events in the System log: Event ID: 142 Message: The time service has stopped advertising as a time source because the local clock is not synchronized. Event ID: 139 Message: The time service has started advertising as a time source. These two messages appear in pairs every hour or so. Event 142 appears 14 to 16 minutes after 139 appears. Going back a few months, these events appear: Event ID: 35 Message: The time service is now synchronizing the system time with the time source time.windows.com,0x9 (ntp.m|0x9|0.0.0.0:123-65.55.21.21:123). Event ID: 37 Message: The time provider NtpClient is currently receiving valid time data from time.windows.com,0x9 (ntp.m|0x9|0.0.0.0:123-65.55.21.21:123). Event ID: 47 Message: Time Provider NtpClient: No valid response has been received from manually configured peer time.windows.com,0x9 after 8 attempts to contact it. This peer will be discarded as a time source and NtpClient will attempt to discover a new peer with this DNS name. The error was: The time sample was rejected because: The peer is not synchronized, or it has been too long since the peer's last synchronization. These three events only appear once in the log, back in October.

  Read the article

• Missing Home Folder XP Clients 2008R2 Domain

  - by minamhere

  We just completed a migration from Server 2003 to Server 2008R2. Everything seems to have gone well except that many of our desktops have stopped mapping the Home Folder as set in Active Directory. Other mappings that are defined on individual clients are mapping just fine, these mappings are all on the same file server as the failing Home Folders. Half of the users are on 1 file server and half are on another. Users from both servers are having this problem. I have enabled the Group Policy setting to "Wait for network before logging in". I enabled the policy to "Run Logon Scripts synchronously". There are no errors on the Domain Controller or either File Server. When I enabled Group Policy Preferences as an attempted workaround, I get this error: The user 'V:' preference item in the '<Policy Name>' Group Policy object did not apply because it failed with error code '0x800708ca This network connection does not exist.' This error was suppressed. This seems to indicate that the network connection is not ready by the time Group Policy is processed. But isn't this the point of the "Wait before logging in" and "Run Logon scripts synchronously" settings? Some other background facts: The new Server 2008R2 installation is a Virtual Machine. It is on a new Subnet in a different building from the old server. DNS and DHCP were also migrated from the old DC to this new DC. These Home Folders were all working properly before the migration. Are there new security restrictions/policies in Server 2008R2 that might be causing this? Is there a way to check whether I have an underlying network connectivity issue? Maybe moving the server to the new building is causing a delay/timeout? Any thoughts or ideas on what could be causing this or how I can resolve this? Thanks.

  Read the article

• Update BIOS on Sun Fire X4150 server

  - by Massimo

  I have some Sun Fire X4150 servers with a very old BIOS release (1ADQW015), which seems to have some compatibility problems with WMware ESX Server 3.5 and Windows 2008 R2 virtual machines; so I want to update the BIOS on them. The problem: according to this page, if your servers run ELOM (mine do), you first need to update to the latest ELOM release, then to the interim transition release, then finally you can update to the latest one. Ok, I'm willing to do that... but it looks like Sun (now Oracle) will happily let you download the latest firmware DVD (3.3.0), but it will not let you download the transition release (2.0) if you don't have a support contract. Well, I actuall don't care at all about the servers' management controllers (we don't even use them), so upgrading from ELOM to ILOM is totally irrelevant to me; but I need to update the servers' BIOS. So my question is: can I update the servers' BIOS to the latest version without doing the full ELOM-to-ILOM migration, or will this not work (or even make the servers unusable)? Do BIOS versions and SP ones need to be matched, or can one be updated without bothering with the other? Bonus question: if this whole ELOM-to-ILOM thing actually is needed in order to update the BIOS, can that 2.0 CD-ROM be obtained without having a support contract with Sun/Oracle (which we are definitely not going to sign, being that quite old hardware)? Update: I tried upgrading only the BIOS on one of the servers, and it didn't boot anymore. So it really looks like a full firmware upgrade is needed, and the management controller and BIOS versions should be kept in sync. So... where can I find that *&!£%$% 2.0 CD-ROM? Or at least the transition firmware that can be found on it?

  Read the article

• New Computer freezing up at random

  - by Benjamin Frost

  Since I built my system about 4 weeks ago I'v been getting random freezes, Sometimes it can happen directly after startup and sometimes it wont freeze up for 3-4 days of 24/7 running. It seems to be happening under all stress loads but mainly when the CPU is under 10% load. It doesn't give me a BSOD or anything, it simply just freezes and repeats the last sound before the freeze until I shut it down by the power button. I'v re-seated everything in the system except the CPU, Cleaned the RAM sockets and gold fittings. None of the components have been clocked above their factory settings as of yet, don't want to overclock them until I sort out these freezes. Temps are all well under the rated max temps, the highest the temps have been are below CPU: Low load: 16-21°C Full Load (100%) 40-43°C *(From HWMonitor by CPUID) GPU 1: Low Load: 25-30°C Full Load (100%): 45-50°C GPU 2: Low Load: 23-27°C Full Load (100%): 45-50°C *(GPU Temps from Catalyst Control Center) General Case temps Rear: 18-20°C Mid: 20-21°C Front (HDD/SSD Bays): 14-19°C (Case temps may be a little off as it's from the Kaze master pro fan controller) I have Un-installed EVERY driver for Motherboard, GPU & Soundcard and Re-installed twice. Windows is all up to date. To date i'v tried the following Running Memtest for 24 hrs straight, No errors Running Memtest on each individual RAM modules, No errors Reseated everything except the CPU Cleaned DIMM Sockets and Gold inputs Tested the Graphics cards 1 at a time Re-arranged all the SATA devices to run on Chipset controlled ports Re-installing all drivers OS: Win7 Professional 64bit Motherboard: ASRock X79 Extreme9 CPU: i7 3930k 3.2GHz GPU: Sapphire 7950 OC Edition V2 (2 card Crossfire) RAM: G.Skill Ripjaws Z F3-17000CL11Q-16GBZL 16GB (4x4GB) DDR3 Boot Drive: OCZ Agility 4 128GB Data Drive 1: Western Digital Black 2TB Data Drive 2: Western Digital Black 2TB Data Drive 3: Western Digital Green 3TB Power Supply: Corsair AX1200 Gold

  Read the article

• Windows 7 - system error 5 problem

  - by Ian

  My wife has just had a new computer for Christmas (with an upgrade from VISTA to Windows 7), and has joined the home network. We are using a mix of WindowsXP and Ubuntu boxes linked via a switch. We are all in the same workgroup. (No domain). Internet access, DHCP, and DNS server is an SME server that thinks it is domain controller (although we are not using a domain). I need to run a script to back up my wife's machine (venus). In the past the script creates a share on a machine with lots of space (leda), and then executes the line. PSEXEC \\venus -u admin -p adminpassword -c -f d:\Progs\snapshot.exe C: \\leda\Venus\C-drive.SNA With the wife's old XP machine, this would run the sysinternals utility, copy shapshot,exe to her machine and run it, which would then back up her C: drive to the share on leda. I cannot get this to work with Windows 7, nor can I link through to the C$ share on her machine. This gives me a permissions error (system error 5). The admin account is a full admin account. And yes - I do know the password. The ordinary shares on her machine work fine! I guess I'm missing something that Microsoft have built into Windows 7 - but what? The machine is running Windows 7 business, with windows firewall, AVG anti virus, and all the crap-ware you get with a new PC removed. Thanks

  Read the article

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• Domain authentication over OPEN wireless pre-logon (Windows 7 Pro) - No logon servers avail

  - by Shadow00Caster

  I have a plethora of laptops that are joined to an AD domain. I have an enterprise wireless system setup, the users of these laptops will be using an OPEN unsecured SSID which will ultimately have a captive portal that uses Radius-AD auth and firewall rules to allow access pre-captive portal auth to the proper ip's/ports of DC's etc for auth etc. I already have other laptops/users connecting to another SSID with 802.11x and SSO, all works perfectly pre-logon etc. My problem is with this open network, for some reason I cannot get the machines to auth to AD. The laptops connect to the wireless network, I confirm this on the controller and can ping the laptop at startup. I sharked the wires on the 2 DC's that these machines auth to, I can see a DNS SOA update from a laptop im testing with and can ping that test laptop from both DC's. When I try to logon, "There are currently no logon servers available to service the logon request." The shark shows no incoming connections to either DC even though the laptop is connected and pingable. Any help is greatly appreciated.

  Read the article

• New SSD freezing on older motherboard (intel G31)

  - by DJM

  I have an ECS G31T-M motherboard running a Core2 Quad processor, 4gb RAM, Windows 7 32bit, Geforce 9600GT. Bought a Sandisk Extreme III 120GB (SDSSDX-120G-G25) and installed today. I'm outputting this from my 9600GT with included TV-out adapter to Component video (to my HDTV). This motherboard is SATA 2 and from what I can tell, SSDs run on the IDE controller and there is nothing fancy to set up advanced features of SSDs. I've noticed on other forums (but not verifying with ECS) this board does not support AHCI. I have two versions of Windows 7 installed on two drives, the SSD and an old 500G disc drive. When booted from my older 500G HDD, video plays fine on the HDTV. When booting the SSD windows 7 install, I am freezing constantly, as in, video plays OK for a minute, then picture freezes for 1-3 minutes (sometimes as audio continues playing) and returns for 20-30 seconds before doing the same thing again. Other tasks such as basic maneuvering through file folders seems to be no problem. Please help!! Do I need a new system for this thing to work, or could there be other fixes? I updated firmware to R201 to no avail. DJM

  Read the article

• USB To Serial under OpenSuse 11.3

  - by Exsisto

  I have a LogiLink USB-To-Serial adapter. This has the PL2303 chip inside. When I insert the device: [26064.927083] usb 7-1: new full speed USB device using uhci_hcd and address 9 [26065.076090] usb 7-1: New USB device found, idVendor=067b, idProduct=2303 [26065.076099] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [26065.076105] usb 7-1: Product: USB-Serial Controller [26065.076110] usb 7-1: Manufacturer: Prolific Technology Inc. [26065.079181] pl2303 7-1:1.0: pl2303 converter detected [26065.091296] usb 7-1: pl2303 converter now attached to ttyUSB0 So the device is recognized and the converter is attached to ttyUSB0. When I do screen /dev/ttyUSB0 9600 I get the error: bash: /dev/ttyUSB0: Permission denied So I went looking in the file permissions. ls -l from the /dev folder reports: crw-rw---- 1 root dialout 188, 0 2011-04-26 15:47 ttyUSB0 I added my user lars to the dialout group. When I use the commands groups under lars it shows that I'm in the group. Though I still recieve the permissions denied error, as lars, and as root. I'm trying to connect to a console cable to configure some Cisco switches. My OS is OpenSuse 11.3 x86_64 with kernel version 2.6.34.7-0.7-desktop.

  Read the article

• Linux machine can't find its tape drive

  - by Kyle Hodgson

  I have an older HP NetServer LPr with what is apparently a Symbios SCSI card connecting to a Quantum SuperLoader 3 that is DLT based. From time to time, we seem to lose the connection to the autoloader. It's usually due to flaky power, but not totally sure why; sometimes when this happens the Autoloader's LED's are orange and it needs to be power cycled. The annoying workaround currently is to reboot the machine. As it is our production VPN and DNS server in addition to being our backup server, this is less than optimal. In Debian (Sarge) is there not some command one can type to get the card to notice that it has the autoloader connected again? dcr1:/proc# grep -i symbios /proc/pci SCSI storage controller: LSI Logic / Symbios Logic 53c895 (rev 1). dcr1:/proc# uname -a Linux dcr1 2.4.27-3-686 #1 Tue Dec 5 21:03:54 UTC 2006 i686 GNU/Linux dcr1:/proc# mt status mt: /dev/tape: No such device dcr1:/proc# ls -l /dev/tape lrwxrwxrwx 1 root root 8 2007-02-07 16:01 /dev/tape -> /dev/st0 dcr1:/proc# That mt status command will show the actual st0 status when things are working correctly. The No such device message is usually the second clue that we need to reboot - the first clue is usually that the backups didn't run.

  Read the article

• Mirror a RAID0 volume

  - by Ghostrider

  I have two SSD running in RAID0. The capacity and speed are just great. I use Windows Home Server to do incremental daily backups. This is fine and well and I've successfully restored from these backups. However. When one of the disks physically died. I was stuck without a working system until the replacement arrives so that I can restore the array from backup. WHS restoration takes about 5 hours which basically means that I'm losing entire day for the process. Is it possible to set up kind of a recovery volume for the RAID array? Use a single mechanical HDD that would be updated with the exact clone of the RAID array on a daily basis. This way if the array goes offline for some reason, I can just boot from the mechanical HDD, lose some perf but will still be able to work. The machine in question runs Windows 7. Creating RAID01 is not an option because of the high price of the SSD and the fact that it still doesn't protect against failure of RAID controller. Is there any way it can be set up?

  Read the article

• Expected IOPS for log writing on PS6000X SAN?

  - by dssz

  Customer is experiencing poor Sybase ASE 15 performance on a PS6000X SAN with 16 X 450GB 10K in RAID-50. The server is a Dell R710 running 2003 server R2 64bit in ESX 4.0.0,256968 I've used sqlio to benchmark the sequential write performance of 4KB blocks on the drive. sqlio -kW -t1 -s600 -dE -o1 -fsequential -b4 -BH -LS sqliotestfile.dat Result is 1900 IOPS. However, when Sybase is running a sustained workload of small inserts SAN HQ shows a consistent 590 IOPS (and 100% 4K write activity). It also shows that the write latency increases to 1.2ms from <1ms. Monitoring and tests in Sybase demonstrate the performance problem is IO related and in particular there is a lot of wait time writing to the log. The SAN indicates that write caching is enabled. What IOPS should the SAN be capable of for 4k sequential write activity? Also, with write caching enabled, shouldn't the controller be batching up the 4K writes into something more efficient? Also, any tips on Sybase on ESX would be appreciated.

  Read the article

• Error 53 - The network path was not found.

  - by Jack

  I have a machine in my Active Directory Domain that I can no longer "net view" from other machines in the domain. This is a Windows XP Pro machine. It is hosting a VMWare virtual of my Domain Controller. If I attempt to net view [machine name] I get system error 53, The network path was not found. This is not a DNS issue, the same thing happens with the machine's IP. I don't think it's a firewall issue, I turned the firewall off on this machine. As I mentioned, it has worked in the past, and then stopped for no reason that I can see. I (intentionally) didn't change the software. I CAN get to the VMs hosted on this machine, can connect to their shares, net view them, etc. All other machines can see each other. In fact, the problem machine can see other machines and access their shares just fine. I tried removing the machine from the domain and re-adding it. I tried deleting the shares and recreating them. Not sure how to troubleshoot this any further. Any ideas?

  Read the article

• help with xorg.conf: xrandr on one of two widescreen monitors; rhel5, kde, ATI Radeon X1300

  - by user35997

  Can anyone help with me configure my dual-screen monitors for rotation? I have xrandr 1.1. Have tried various approaches, nothing takes. I can't even get the xrandr options to show up in KDE's Display control panel. Thanks1 My lspci output: 03:00.0 VGA compatible controller: ATI Technologies Inc RV516 [Radeon X1300/X1550 Series] My current xorg.conf (works, minus screen rotation): # Xorg configuration created by system-config-display Section "ServerLayout" Identifier "Multihead layout" Screen 0 "aticonfig-Screen[0]" 0 0 InputDevice "Keyboard0" "CoreKeyboard" Option "Xinerama" "off" Option "Clone" "on" EndSection Section "Files" EndSection Section "Module" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" Option "XkbModel" "pc105" Option "XkbLayout" "us" EndSection Section "Monitor" ### Comment all HorizSync and VertSync values to use DDC: Identifier "Monitor1" VendorName "Monitor Vendor" ModelName "Dell 2407WFP (Digital)" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 76.0 Option "dpms" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "Videocard0" Driver "vesa" EndSection Section "Device" Identifier "Videocard1" Driver "vesa" VendorName "Videocard Vendor" BoardName "ATI Technologies Inc RV516 [Radeon X1300/X1550 Series]" BusID "PCI:3:0:0" EndSection Section "Device" Identifier "aticonfig-Device[0]" Driver "fglrx" Option "DesktopSetup" "horizontal" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection SubSection "Display" Viewport 0 0 Depth 16 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Videocard1" Monitor "Monitor1" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 16 Modes "1920x1200" "1280x1024" "800x600" EndSubSection EndSection Section "Screen" Identifier "aticonfig-Screen[0]" Device "aticonfig-Device[0]" Monitor "aticonfig-Monitor[0]" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1920x1200" "1280x1024" "800x600" EndSubSection EndSection

  Read the article

• Windows XP - Power surge on hub port

  - by Swift-Tuttle

  Since last few weeks I constantly get this error, as status bar balloon: Power Surge on Hub Port - A USB device has exceeded the power limits of its hub port. Due to this now I am unable to access any USB devices properly, they get disconnected intermittently. I did quite a few things to resolve this problem, firstly obviously through the Windows help. I even tried all the things told on the Microsoft website(which essentially says is to check and update the driver) but in vain. One suggestion, I found when I google'd was to disable the USB2 controller through the Device Manager and since at every startup the System configuration comes up complaining that it has been changed etc.(On that same site it is mentioned to ignore this message.) But after everything I still cant solve this problem. Any help is much appreciated. The system is installed with Windows XP service Pack 3 and all the updates till last month. Please let me know if any other hardware info is required. **UPDATE** My laptop is about 5 years old now, its an HP with Celeron 1.4G processor. Windows XP SP3 installed. All latest windows updates installed. 2 USB ports available. BIOS is HP 68DTD ver F.0A Do I need to update my BIOS from somewhere ? or is this a hardware problem altogether?

  Read the article

• Microsoft Office 2003 applications crash on 'Save As' to a network mapped drive

  - by Archit Baweja

  Hey guys, so I'm not sure if it belongs on ServerFault forums so figured I'd ask here first because its a workstation/client side issue. I have a client where we have windows server 2003 setup, with windows xp professional setup on all the workstations. We've setup a 'domain' and all workstations logon to the domain (authenticated by the Windows Domain Controller), and in the logon script we map drives on to each workstation. Everything is working peachy except for one workstation, where when I open a file in excel from a mapped drive, it opens fine, but when I go to hit Save As, the Save As dialog pops and hangs up. I cannot perform any other action in excel. When I try cancel the Save As dialog, excel crashes. The mapped drive opens up fine in Windows Explorer. To further investigate this issue, I created a new blank text document on the network drive in Windows Explorer. I then opened it. Then hit save as, and the Save As dialog opened up fine and it would let me save the document. I repeated the above steps for a word document. However this time the Save As dialog hung/froze again. So I'd imagine its a Microsoft Office Issue. Any ideas?

  Read the article

< Previous Page | 333 334 335 336 337 338 339 340 341 342 343 344  | Next Page >