Search Results

Search found 18488 results on 740 pages for 'android networking'.

Page 340/740 | < Previous Page | 336 337 338 339 340 341 342 343 344 345 346 347  | Next Page >

• Slow internet using Arch Linux

  - by GZaidman

  after a week or so of using Arch Linux I cant access the internet - it takes around 5 mins to load google (most of the other websites just give me a timeout), pacman's downloading speed range between 5-2Kbs, and pinging google takes around 9Kms. I'm connected using wireless network (wifi card is Intel Ultimate 6300 and router is Edimax 6524n). Every other Windows machine that's connected to the network (and even the T410 running Windows) is fine, so the problem lies in Linux. So far, i checked the resolv.conf file (my router ip address is listed), and the hosts file (pretty much default), and I disabled the ipv6 module. None of that helped. PS: i'm using NetworkManager (but the problem still occurs when connecting using wicd) running on Gnome3. Thanks in advance for any help you can provide! EDIT: something really strange happens whenever I ping google: i get an unknown host 'google.com', but the bit rate from the card jumps at the exact second I ping google (so far, the bit rate jumped to 54Mb/s from 1Mb/s over the course of 4 pings).

  Read the article

• How can I use two Internet connections in Ubuntu?

  - by Martin

  My goal is to be able to do something like this: curl google.com --interface ppp0 curl google.com --interface p2p2 ppp0 is a DSL connection, and p2p2 is a separate direct Internet connection. Currently I can only get one of these to work at a time. When I enable one, the other one stops working. /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # DSL auto p2p1 iface p2p1 inet manual auto dsl-provider iface dsl-provider inet ppp pre-up /sbin/ifconfig p2p1 up # line maintained by pppoeconf provider dsl-provider # DIRECT auto p2p2 iface p2p2 inet dhcp ifconfig: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 p2p1 Link encap:Ethernet inet6 addr: fe80::20a:ebff:fe21:99c6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 p2p2 Link encap:Ethernet inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20a:ebff:fe17:1249/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ppp0 Link encap:Point-to-Point Protocol inet addr:53.193.231.167 P-t-P:53.193.224.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 10.0.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 53.193.224.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 p2p2 By default, only ppp0 works. If I run "route add default gw 192.168.1.1 p2p2" then I can use p2p2 but ppp0 stops working. If I then run "route add default gw 53.193.224.1 ppp0" then I can use ppp0 again but p2p2 stops working. What can I do to be able to use both interfaces selectively?

  Read the article

• Looking for software to create a personal hotspot on Mac OS X (not using the built-in ability)

  - by Fred

  I got my nifty little MacBook Air today. Since I will be going on travel I was hoping to use my iPad 3G as screen extension with Air Display. It works being in a shared WiFi network. Sadly Apple is a bit restrictive on the tethering with their mobile devices such as the iPad. Now I read iOS 4.3 will enable the iPad to use tethered networks. But the feature will not be working for iPad 3G. I assume their big partner telecom companies fear everyone will quit their internet contract with them. So I want to create a personal hotspot on my MacBook and use it on my iPad. But the iPad is not able to use this network. The network is visible but not usable. On Windows there is this connectify program which lets the PC act as wireless router. Does anybody know a similar program for Mac which would turn it into a wireless router? Or is there something I don't see with Mac OS X's builtin features?

  Read the article

• Connect a PC to Mac OS X Server

  - by Paul Sheldrake

  I'm trying to connect to a server at work which is run on a Mac but I have a PC (windows 7) at home. I have path to connect in the format of afp://server.com/files. Is there a client that I need to install on my PC that I can use to login? Thanks, Paul

  Read the article

• How to Set Linux Bonding Interface to Gigabit

  - by Kyle Brandt

  I have enabled Linux active backup mode bonding. Each interface is a gigabit interface, but the bond interface seems to end up at 100 Megabit: bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full. ... bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON ... bonding: bond0: backup interface eth1 is now up ethtool apparently can't provide info on bond: sudo ethtool bond0 Settings for bond0: No data available So does this mean I am operating at 100 or 1000 Megabit (My guess is 1000)? If it is only 100, what options in the ifcfg scripts or the modprobe bonding options do I need to sett to make it 1000?

  Read the article

• Windows 7 Forbid connecting to a specific wireless network

  - by Elliot

  Does anyone know how to tell windows 7 to bar a wireless network? It keeps logging into a random open one with no bandwidth my neighbors have instead of the good one we have here. I keep unchecking "automatically log in if available" and it keeps re-checking itself. I want it to NEVER log into this network no matter what without manual intervention. I do not want to disable auto connecting, just tell it "do not ever connect to this one without my express permission".

  Read the article

• MikroTik ipv6 Tunnel

  - by MikeSmitty

  I've got a MikroTik router set up with the latest stable OS on it, and I just set up an ipv6 tunnel with Hurricane Electric, but I'm having an odd issue with it. I can't ping anything until I first ping the tunnel endpoint on HE's side. After that I can ping any ipv6 address fine, but give it a little time (say, maybe 30 sec) and I can't ping any ipv6 addresses again. Whenever it stops allowing ping to go through I notice the counter on my firewall rule that drops invalid connections goes up. this is my ipv6 firewall config: add action=accept chain=input comment="" connection-state=established \ disabled=no in-interface=sit1 add action=accept chain=input comment="" connection-state=related disabled=no \ in-interface=sit1 add action=accept chain=input comment="" disabled=no in-interface=bridge \ src-address=ipv6_address_here/64 add action=drop chain=input comment="" connection-state=invalid disabled=no \ in-interface=sit1 add action=drop chain=input comment="" disabled=no in-interface=sit1 Any ideas on what it could be?

  Read the article

• Top ten security tips for non-technical users

  - by Justin

  I'm giving a presentation later this week to the staff at the company where I work. The goal of the presentation is to serve as a refresher/remidner of good practices that can help keep our network secure. The audience is made up of both programmers and non-technical staff, so the presentation is geared for non-technical users. I want part of this presentation to be a top list of "tips". The list needs to be short (to encourage memory) and be specific and relevant to the user. I have the following five items so far: Never open an attachment you didn't expect Only download software from a trusted source, like download.com Do not distribute passwords when requested via phone or email Be wary of social engineering Do not store sensitive data on an FTP server Some clarifications: This is for our work network These need to be "best practices" tips for the end-user, not IT policy We have backups, OS patches, firewall, AV, etc, all centrally managed This is for a small business (less than 25 people) I have two questions: Do you suggest any additional items? Do you suggest any changes to existing items?

  Read the article

• Should I enabled 802.3x hardware flow control?

  - by Stu Thompson

  What is the conventional wisdom regarding 802.3x flow control? I'm setting up a network at a new colo and am wondering if I should be enabling it or not. My oh-cool-a-bright-and-shiny-new-toy self wants to enable it, but this seems like one of those decisions that could blow up in my face later on. My network: An HP ProCurve 2510G-24 switch A pair of Debian 5 HP DL380 G5's with built-in NC373i 2-port NIC LACP'd as one link. 9000 jumbo frames enabled. (Application) A pair of hand-built Ubuntu server with 4-port Intel Pro/1000 LACP'd as one link. 9000 jumbo frames enabled. (NAS) A few other servers with with single 1Gbps ports, but one with 100Mbps. Most of this kit is 802.3x. I've been enabling it as I go along, and am about to test the network. But as my 'go live' day nears, I am worried about the 802.3x decision as I've never explicitly used it before. Also, I've read some 10-year old articles out there on the Intertubes that warn against using flow control. Should I be enabling 802.3x hardware flow control?

  Read the article

• Network transfer from host to VM very slow - VMWare Server & Windows 2003 Server

  - by barfoon

  Hey everyone, Im trying to transfer a file from a Windows 7 host running VMWare Server to a Windows 2003 server VM, and it's painfully slow. I've tried adding/adjusting registry keys and settings found on KB articles, and still nothing. Ive tried this: http://support.microsoft.com/kb/898468 http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1619 Vmware tools are installed. Any ideas? Thanks,

  Read the article

• How can find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• Bandwidth Control on our Internet Connection

  - by AlamedaDad

  Hi all, I have Covad dual/bonded T1 service in our office coming through a Cisco 1841 and then through a Sonicwall 3060Pro/Enhanced SW firewall. The problem I'm looking for some input on is how to limit the amount of bandwidth any single user/PC can user for downloading a file from the Internet. It's become an issue that when one person happens to download let's say an ~300MB file, normal internet access for the other employees slows to a crawl. I've seen through MRTG that in fact usage of the circuit jumps to the full 3mb for the duration of the download and then drops. Is it possible to control this? I'm not familiar with QOS or the like so I'm not sure. Any help on this would be appreciated. Thanks...Michael

  Read the article

• Domain connection shows as "unauthenticated"

  - by gareth89

  I have seen various different questions for this problem floating around but either the circumstances arent the same or the solution doesnt work so thought i would post it to see if anybody has any suggestions. Various domain PCs and laptops appear to randomly give the connection name of "lewis.local 2(Unauthenticated)" - lewis.local being our domain - and provides an exclamation mark where the network type logo is normally shown. This also appears to happen every time connecting via vpn. Our setup is: 2 servers both running windows server 2003 R2 (x32) main server has AD, DNS and DHCP installed IPv4 on approx 30 client machines (some wired, some wireless) If anybody has any thoughts on solutions i would appreciate it. I have tried removing all but AD server roles, resetting all of the systems and nothing. It doesnt prevent anything from working just like a domain connection most of the time however it is getting fustrating! Also dont know if it could have anything to do with it but the DHCP server seems to have quite a long lead time on issuing the IP address to the client.

  Read the article

• Multiple VLAN on one switch port

  - by Macropus

  I have a HP ProCurve 1810G-8 which I currently use as a normal switch between 3 servers and a firewall. 2 of the servers are ESXi hosts, and one is a Nexentastor box with 2 iSCSI target LUNs. As the iSCSI traffic is on the same LAN as all other traffic, I would like to switch this to use a SAN for iSCSI traffic and the LAN for all other traffic. The Nexentastor box only has 2 NICs, and as such, with a physical arrangement, I presume that one must be plugged into the SAN VLAN and one on the LAN VLAN ports of the switch. Is there a way to have multiple VLANs over the same port? e.g. the Nexentsator box has 2 NICs, both plugged into the switch, both ports with access to both of the VLANs?

  Read the article

• How can Windows XP/7 users cleanly connect to Mac OS X Server 10.9.4 Mavericks with Active Directory integration?

  - by JakeGould

  I’m a Linux/Unix systems admin who also manages a Macintosh server infrastructure & there is a lone Mac Mini in the mix running 10.9.4 that I would like Windows XP & Windows 7 users to connect to with little or no hassle. The problem? Windows users can’t seem to even get to the point of a password prompt yet connect. Mind you this server replaced a Mac OS X 10.6.8 server that had issues, but never had issues with Windows users connected. The gist of this post is: The tons of different messages out there about Mac OS X 10.9.4 Samba support are mind-numbingly confusing. Can anyone share some solid specifics here? I’ve read pieces like this one here that suggest turning off file sharing & then adding a share with AFP/SMB enabled would work. But the suggestion seems to apply to 10.8. And from what I know a lot has changed in Samba support in 10.9 let alone the iterations to 10.9.4. Then I found this great tutorial here that explains things step-by-step. Which seems like it should work, but the problem is the example given applies to a local user created on the Mac when I would like users in an Active Directory group—which the Mac is bound to—access the Mac Mini shares. There are also tons of great tips here on MacWindows.com but nothing seems solid to the issue I am facing. So from what I am reading these are my options: Local User Versus Active Directory: Setup a common local user on the Mac OS X 10.9.4 server to be used for Samba sharing since Active Directory won’t work. Is this really the case? Because loss of AD integration is a major pain. Do Extended File Attributes Get Retained from Windows Users: If this were to work, how do extended attributes come into play? Loss of metadata & related info is not an option. How Fragile is Any of this to Updates: How does any of this shake out with Mac OS X updates as well as Windows updates? Installing Official, Open Source Samba: Would upgrading the Samba install on the server to the official open source Samba via a package like SMBUp or via the Hombrew method described here help or make the issue worse? I fully understand there have historically been issues in mixed environments, but nowadays Windows users connecting to a Mac seem to have a truly hellish road ahead of them. Unless I am missing something?

  Read the article

• wireless internet in linux is very very slow... but in windows.... everythnings fine

  - by Cody Acer

  yesterday when i was connecting to our neighbors wifi connection which is the signal strength is below 50%, i cant browse anything... even ping to gateway. 100% packet loss, and sometimes.. i can connect awesomely i can open my facebook account for 15 minutes but after 15min.. connection is extremely slow. but not windows i can surf even the signal str is very poor weird ey??.. root@Emely:~# lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx DMI Bridge [8086:a010] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a011] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller [0380]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a012] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] 00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 3 [8086:27d4] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ehci-pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: lpc_ich Kernel modules: lpc_ich 00:1f.2 SATA controller [0106]: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel modules: i2c-i801 05:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01) Subsystem: Wistron NeWeb Corp. Device [185f:051a] Kernel driver in use: bcma-pci-bridge Kernel modules: bcma 09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: sky2 Kernel modules: sky2 root@Emely:~# ip addr show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff inet 192.168.1.108/24 brd 192.168.1.255 scope global wlan0 inet6 fe80::21b:b1ff:fea9:ace0/64 scope link valid_lft forever preferred_lft forever root@Emely:~# ip link show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff root@Emely:~# rfkill list all 0: samsung-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: samsung-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no 3: phy0: Wireless LAN Soft blocked: no Hard blocked: no is this a wireless driver issue?

  Read the article

• OS X won't see Windows 7 in network (and vice versa)

  - by meds

  I've enabled SMB sharing in OS X Lion and have added folders to share, it says 'Windows Sharing: On' with a green circle next to it (from the sharing window) and that to access the volume I will need to to go to \\192.168.0.17. It also says that the OS X should be visible as 'macbook' in the network. Both my WIndows 7 and OS X are connected to the same network, yet when I try to go to \\192.168.0.17 or from the Mac try to go to my Windows system (smb://192.168.0.6) the two OSs don't see each other. Any ideas why? Attempting to ping the Mac from Windows results in this output in the command prompt: Pinging 192.168.0.17 with 32 bytes of data: Reply from 192.168.0.6: Destination host unreachable. Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.0.17: Packets: Sent = 4, Received = 1, Lost = 3 (75% loss), ipconfig in Windows is: Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::8918:efd1:b05c:890f%21 IPv4 Address. . . . . . . . . . . : 192.168.0.6 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.1 Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::98ab:63fc:3c07:d837%13 IPv4 Address. . . . . . . . . . . : 192.168.74.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::80ff:c575:7b50:3a10%14 IPv4 Address. . . . . . . . . . . : 192.168.21.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Tunnel adapter isatap.{2E97D0AE-9E18-4072-AC23-1979BA0DCB79}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{E260CE43-E9A7-4DE0-A88E-4EAFF68ACDDB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{A5130812-59CE-4DDF-9C35-9433BCED9831}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{134BCAE7-CFFF-4A98-8DA0-3708806AABEB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{8D9E3B8F-161C-4ACE-B211-3EDD694416B2}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : in OS X: lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 stf0: flags=0<> mtu 1280 en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=2b<RXCSUM,TXCSUM,VLAN_HWTAGGING,TSO4> ether c8:2a:14:01:24:c1 media: autoselect (none) status: inactive en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether e0:f8:47:0c:fe:04 inet6 fe80::e2f8:47ff:fe0c:fe04%en1 prefixlen 64 scopeid 0x5 inet 192.168.0.17 netmask 0xffffff00 broadcast 192.168.0.255 media: autoselect status: active p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304 ether 02:f8:47:0c:fe:04 media: autoselect status: inactive fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078 lladdr 70:cd:60:ff:fe:d8:f1:32 media: autoselect <full-duplex> status: inactive

  Read the article

• Windows 7 can't connect to via ethernet to Airpot Extreme

  - by Mr AJL

  I have an Airport Extreme, and everything works beautifully on the Mac, but my Windows 7 computer, which is connected via a regular ethernet cable, can't see any network. The Windows computer says there's no cable connected. Any ideas? Is there some kind of setting you have to enable with the Airport utility? I looked everywhere but can't find anything. Or do I need to install that Airport utility something on the PC just to connect to the router? (Haven't tried because the PC has no CD drive)

  Read the article

• Having trouble setting up my router

  - by indyK1ng

  I just moved into my apartment and the Internet connection is working. It's Comcast in case that matters. Anyway, I'm having trouble setting up my wireless router (Netgear WNR2000) to work with it. Are there any settings that I could be missing? I currently have it set up to use a static IP address and I found the DNS servers I'm supposed to use and the Internet light is green, but I can't get out to the Internet. When I am trying, I'm connecting to an Ethernet port on the back of my router. Is there a setting I'm missing or a setting that I have set wrong? I used the automatic set up wizard to learn that it's a static IP address. Any help would be appreciated. I am currently only able to use my Linux machine, so please make any help in Linux commands. Yes, I can connect to the Internet if I connect to the modem directly and I've been using the web interface when I'm connected to the router, so I suppose I can ping the router. My router detected the connection as using a static IP address, so I connected to the modem directly and figured out what my IP address, gateway, and mask were as well as DNS servers.

  Read the article

• Troubleshooting an unstable internet connection

  - by Konrad Rudolph

  My MacBook Pro running OS X (10.9, but I had the same problem before) is connected to a Belkin router via WiFi and, using Virgin Media as the ISP, to the internet. The connection is extremely unstable – on some days, I get a ping timeout every few seconds. In addition, some domains seem to suffer general connectivity issues. For instance, I often find that while the youtube.com website loads, none of the videos (which are hosted on a separate domain) do. At other times, videos load but always fail to buffer, even though the actual connection speed is ok, even though I’ve disabled dash playback. Since I’m living in a rented room and the ISP contract isn’t actually mine I’ve got only limited possibilities of addressing the problem. In particular, I have no access to the router configuration and my non tech savvy landlady, while sympathetic, is not in a great hurry to hand the problem over to the ISP’s customer support. What’s more, I seem to be the only person in the house experiencing these problems – but I can imagine that this is simply because I’m the only one who’s using the internet continuously. I’m searching for specific tests that might be able to pinpoint – and ideally solve – the problem. So far all I’ve managed to do is establish that Virgin is routing my traffic in mysterious ways. Here’s an excerpt from traceroute google.co.uk. It’s worth mentioning that the host name doesn’t seem to matter a lot, the trace route is always the same. traceroute: Warning: google.co.uk has multiple addresses; using 62.254.36.148 traceroute to google.co.uk (62.254.36.148), 64 hops max, 52 byte packets 1 (192.168.2.1) 1.112 ms 1.300 ms 2.359 ms 2 10.100.32.1 (10.100.32.1) 11.926 ms 10.217 ms 24.987 ms 3 cmbg-core-1a-ae3-610.network.virginmedia.net (80.1.202.93) 28.809 ms * 66.653 ms 4 popl-bb-1b-ae16-0.network.virginmedia.net (212.43.163.141) 13.759 ms 126.504 ms 20.472 ms 5 nrth-bb-1b-et-010-0.network.virginmedia.net (62.253.175.57) 28.357 ms 16.398 ms 42.387 ms 6 nrth-bb-1c-ae1-0.network.virginmedia.net (62.253.174.110) 27.441 ms 15.622 ms 12.044 ms 7 lutn-icdn-1-ae0-0.network.virginmedia.net (62.253.175.82) 16.678 ms 28.463 ms 28.253 ms 8 * * * 9 * * * 10 * * * ^C If I let it, this goes on until the end of time. It never seems to reach a destination. Is this normal? A friend living in the same town who is also with Virgin Media has a more conventional traceroute output: 7 hops to google.co.uk, all of which send the ICMP TIME_EXCEEDED response. The obvious fix – rebooting the router – doesn’t seem to help. As far as I can tell, the WiFi connection is stable (I can always ping the router) so the problem is further downstream. I’ve tried using an alternative DNS before (OpenDNS) but if anything, this made things worse. In fact, it made all Google services nigh unreachable.

  Read the article

• TCP/IP Ilustrated 1 second edition [on hold]

  - by user196821

  Well, I want to read and learn about how tcpip works in detail, so I got a copy of the well known book of Richard Stevens. But after a little, I discovered there is a second edition of the book, so I checked it out. But surprisingly, the second edition does not cover some subjects that the first actually does (like telnet, ftp, smtp etc...), so I thought "well I just have to read the misshing chapters on the first edition", but if they removed them in the second, it is for a reason. Is there really a good reason for that?

  Read the article

• Two identical fiber optic broadband lines working as one

  - by Katafalkas

  I have been trying to find an answer to this, but all I can find is hobbyists trying to connect their Linksys devices to get some magic out of them. I am looking for a way I could combine two 100Mbit fiber optic lines into a single connection for our office. I assume it involves some Cisco learning or something similar. Do I need to configure some big router to load-balance the NATing in some way? I assume that many of you have done something similar and hope someone could share their knowledge or at least provide me some tips on how to do this.

  Read the article

• Remote connection IP to use

  - by petwho

  I have two laptops that both run on ubuntu and installed ssh server and ssh client on them. One is usually on my desk at home and one I usually bring to my company. When I'm at home I can easily ssh to one from the other by typing this command (to login to the other laptop whose IP address is: 192.168.0.105) : ssh -p 22 [email protected] However, When I'm at my company, I try to type the same command and ofcourse it doesn't work. I understand that when at home I'm on LAN network, that my laptops actually using my ISP's address which differ from 192.168.0.107 asummed 203.113.131.1. So could you tell me what IP that ssh shoud use for my laptop (at work) to connet to my computer at home? Thank you.

  Read the article

• Why the server is not responding?

  - by par

  Hello! Our server occasionally refuses to serve a simple HTML page. This is happening during a relatively high number of requests. However, the processor is not heavy loaded and there are a lot of free memory. The error seems to occure 1 out of 50 requests in average, depending on the server load. I need to find the source of the problem and take the appropriate actions to eliminate it. I have a suspicion that the problem source is a huge number of incoming network packets. There are 5000 packets per second on average. Traffic - 2 MBits/sec Can this be the cause of the error? There is an interesting thing, in case the server fails to respond, the request string is not logged to access.log by Apache. The error is repeatable from several client computers. DNS is not involved, since I have accessed the server by the IP. I have profiled the problem case with tcpdump utility. These are the good and bad sessions traced by tcpdump. The request is the same in both experiments. Good - server returns response. Bad - no response, time-out error. ---- Bad ---- 12:23:36.366292 IP 123.45.67.890.61749 > myserver.superbservers.com.www: S 2125316338:2125316338(0) win 8192 <mss 1460,nop,wscale 2,nop,nop,sackOK> 12:23:39.362394 IP 123.45.67.890.61749 > myserver.superbservers.com.www: S 2125316338:2125316338(0) win 8192 <mss 1460,nop,wscale 2,nop,nop,sackOK> 12:23:45.365567 IP 123.45.67.890.61749 > myserver.superbservers.com.www: S 2125316338:2125316338(0) win 8192 <mss 1460,nop,nop,sackOK> -------- ---- Good ---- 12:27:07.632229 IP 123.45.67.890.63914 > myserver.superbservers.com.www: S 3581365570:3581365570(0) win 8192 <mss 1460,nop,wscale 2,nop,nop,sackOK> 12:27:10.620946 IP 123.45.67.890.63914 > myserver.superbservers.com.www: S 3581365570:3581365570(0) win 8192 <mss 1460,nop,wscale 2,nop,nop,sackOK> 12:27:10.620969 IP myserver.superbservers.com.www > 123.45.67.890.63914: S 2654770980:2654770980(0) ack 3581365571 win 5840 <mss 1460,nop,nop,sackOK,nop,wscale 6> 12:27:10.838747 IP 123.45.67.890.63914 > myserver.superbservers.com.www: . ack 1 win 4380 12:27:10.957143 IP 123.45.67.890.63914 > myserver.superbservers.com.www: P 1:213(212) ack 1 win 4380 12:27:10.957152 IP myserver.superbservers.com.www > 123.45.67.890.63914: . ack 213 win 108 12:27:10.965543 IP myserver.superbservers.com.www > 123.45.67.890.63914: P 1:630(629) ack 213 win 108 12:27:10.965621 IP myserver.superbservers.com.www > 123.45.67.890.63914: F 630:630(0) ack 213 win 108 12:27:11.183540 IP 123.45.67.890.63914 > myserver.superbservers.com.www: . ack 631 win 4222 12:27:11.185657 IP 123.45.67.890.63914 > myserver.superbservers.com.www: F 213:213(0) ack 631 win 4222 12:27:11.185663 IP myserver.superbservers.com.www > 123.45.67.890.63914: . ack 214 win 108 -------- Hoster: SuperbHosting OS: Ubuntu Server parameters: E6300 CONROE 1.86GHZ 2 X 1MB CACHE 1066 1GB DDR2 667MHZ This is a link to apache configuration file we use http://repkin5.snow.prohosting.com/apache.txt This is server-status report taken right after time-out error. http://repkin5.snow.prohosting.com/server-status.htm There are only 10 Child Servers running out of 120, so enough space for new requests. VMSTAT procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 8900 725900 8468 65684 0 0 5 18 11 33 4 3 92 1

  Read the article

• Looking for a fiber optic "switch" or "router" for home use

  - by Shrout1

  The gist of my question: What is a "fiber optic" switch called? I.E. a layer 2 ethernet switch that uses fiber TX and RX connections and sends layer 2 network traffic between the fiber strands that are connected. Can someone purchase a dedicated fiber switch that does not have copper ethernet ports? What is the current average price of a device like this? Not necessarily looking for product endorsements, just information Might not make sense to go this route if it is too cost prohibitive What type of fiber connector is used for terminating a fiber strand into a jack on the wall? Can fiber be "patched" using two jacks and a "patch" cable? Is signal loss a concern with the longest runs at 100-200ft, a patch cable and media converters? The full story: My parents had unterminated fiber optic cable and terminated Cat5e run throughout their home when it was built in 2004. 10 years later the Cat5e isn't providing the throughput that my father needs to accomplish multiple streams of HD and fast system backups throughout the house. He can't reach gigabit speeds across the distance of the Cat5e runs. We are both interested in terminating the fiber connections and using them as high speed "backbones" to copper switches in each room of the house. It would be easy to attain gigabit speeds (or better, eventually) using the fiber. I have searched and searched for a "fiber optic switch" or "fiber optic router" and cannot find the correct term to describe this piece of hardware. We can use fiber media converters at the end points of each connection, however it would be nice to have a "patch panel" set up in the network closet in the basement that has fiber connections on it and switches the ethernet streams between the connections/systems in the house. Each fiber media converter costs between $50-$100 a piece... After 10 or so terminated connections it might make sense to find a piece of hardware that does not require media converters. That would depend upon the cost of this hardware Somewhat unrelated, if we are able to route between these fiber strands successfully, what is the physical connector type used in a jack on the wall? Just like RJ45 has a wall outlet (depicted below): What is the fiber optic equivalent of this? In the interim could we "patch" a couple fiber strands together in the network closet? Would signal loss be of concern with a run length of 100-200 feet, a patch cable and two media converters? If that would work then it could be used until the funds are available for more.

  Read the article

< Previous Page | 336 337 338 339 340 341 342 343 344 345 346 347  | Next Page >