Search Results

Search found 14402 results on 577 pages for 'interface builder'.

Page 348/577 | < Previous Page | 344 345 346 347 348 349 350 351 352 353 354 355  | Next Page >

• Linux IPv6: DHCP and /127 prefixes

  - by Jeff Ferland

  I've tried multiple pieces of DHCP client and software in attempting to setup a solution for allocating a /127 prefix to virtual machines so that each maintains its own layer 2 isolation. Because there would only be one host assigned to each network, a /64 is impractical. While the prefix size could reasonably be somewhere in the /64-127 range, the crux of the problem has been the same regardless of the software used in configuring: the DHCP call to bring up the interface uses the address advertised by DHCPv6 and inserts two routes: the /127 given by the router advertising packets and a /64 as well. Any thoughts on why I'm getting the additional route added across dhcp client vendors?

  Read the article

• What's causing "shutdown state" after TFTP reloaded Cisco `running-config` on 871?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I tested the 871's flash memory with fsck and rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config?

  Read the article

• how're routing tables populated?

  - by Robbie Mckennie

  i've been reading "tcp/ip illustrated" and i started reading about ip forwarding. all about how you can receive a datagram and work out where to send it next based on the desination ip and your routing table. but what confused me is how (in a home network setting) the table itself is populated. is there a lower layer protocol at work here? does it come along with dhcp? or is it simply based on the ip address and netmask of each interface? i do know (from other books) that in the early days of ethernet one had to set up routing tables by hand, but i know i didn't do that.

  Read the article

• Setting up SharePoint 2010 guides

  - by RobertPitt

  I'm looking for some guides on setting up SharePoint Server 2010. The guides should be focused on the actual web interface side of things such as Permissions, Layouts, Team Sites etc. I have searched high and low for guides and most of them are just "How to install Server 2010". These are useless because the installation is self explanatory. I'm at the stage where I need to learn the config side of things so I can lay my web structure out the way I want it. Has anyone got any good resources?

  Read the article

• How to set the IP address in a customized OpenWRT compilation

  - by Berdus

  I have been struggling today customizing OpenWRT. I checkout the stable using SVN, "make menuconfig" to customize the image, "make" it and run it on a router. Almost all my modifications work, except for the (Seemingly trivial) task of changing the default 192.168.1.1 address. I tried numerous files (scripts as well as config files) but I can't seem to change it (I can change it for a brief moment after boot using the "preinit" file, but after a few seconds it reverts to default). I suspect I should be setting it in the /etc/network file, but modifications there seem to be overwritten during boot. Maybe it has something to do with the br-lan interface? Does anybody have some thoughts on the subject? Thanks!

  Read the article

• How to enable CDR on AsteriskNow 1.5

  - by Michal Niklas

  I have upgraded PBX to Asterisk 1.6.2.7 and now CDR files are not created. It looks that such logging is disabled: Connected to Asterisk 1.6.2.7 currently running on pbx2 (pid = 5824) Verbosity is at least 3 pbx2*CLI> cdr show status pbx2*CLI> Call Detail Record (CDR) settings ---------------------------------- Logging: Disabled Mode: Simple Asterisk shows that CDR modules are loaded: pbx2*CLI> module show like cd Module Description Use Count cdr_manager.so Asterisk Manager Interface CDR Backend 0 cdr_csv.so Comma Separated Values CDR Backend 0 app_cdr.so Tell Asterisk to not maintain a CDR for 0 app_forkcdr.so Fork The CDR into 2 separate entities 0 func_cdr.so Call Detail Record (CDR) dialplan functi 0 cdr_custom.so Customizable Comma Separated Values CDR 0 6 modules loaded How to enable creating CDR csv files?

  Read the article

• Thunderbird-3 keeps on downloading already downloaded messages again?

  - by Vivek Sharma

  I am using Thunderbird for my gmail account, with IMAP settings. All my folders are synchronized. A very strange behavior, after all my mails are downloaded, TB3 starts downloading email again. At times saying "downloading x out of y messages" where x y (like now downloading 19 out of 11 messages). Had the same problem in TB3 for windows so, replaced TB with Outlook-07, issue resolved. But on linux, I dont like the evolution's interface, so i have no choice but to stick to TB. Any suggestions how to TB not eat my bandwidth.

  Read the article

• How to enable RDP to a Server 2008 R2 on another network? VM network

  - by Saariko

  I have a W2008 R2 installed on a different network (I am on 192.168.0.x - new server on 192.168.3.x) I had trouble ping and RDP to it. I disabled the firewall to test the connection: and that opened the ping feature but I still can not RDP to that machine. the allow remote access is enabled As per sinni80 idea - Here is the error message The networks are divided by a Fortigate 60-B router - 2ndy interface for the gateway is 192.168.3.254 (and pingable from all) any to any rule on both networks is in place. As per Joe Schmoe idea - I am able to RDP to 192.168.3.1 from 192.168.3.3 (which is on the same network) Data to add: - The servers are on a VM host, each of the servers has 2 nics one is DHCP enabled into the 192.168.0.x network 2nd is static IP in the 192.168.3.x -- Further information: The network 192.168.0.x - are on a domain network (active Directory) The network 192.168.3.x - are grouped in a workgroup What should I check more please?

  Read the article

• OpenVZ multiple networks on CTs

  - by user6733

  I have Hardware Node (HN) which has 2 physical interfaces (eth0, eth1). I'm playing with OpenVZ and want to let my containers (CTs) have access to both of those interfaces. I'm using basic configuration - venet. CTs are fine to access eth0 (public interface). But I can't get CTs to get access to eth1 (private network). I tried: # on HN vzctl set 101 --ipadd 192.168.1.101 --save vzctl enter 101 ping 192.168.1.2 # no response here ifconfig # on CT returns lo (127.0.0.1), venet0 (127.0.0.1), venet0:0 (95.168.xxx.xxx), venet0:1 (192.168.1.101) I believe that the main problem is that all packets flows through eth0 on HN (figured out using tcpdump). So the problem might be in routes on HN. Or is my logic here all wrong? I just need access to both interfaces (networks) on HN from CTs. Nothing complicated.

  Read the article

• Shortcut to checkout Sharepoint documents?

  - by Benjotron

  I find myself in a lot of situations where I need to download the latest version of a document from sharepoint, or checkout a sharepoint document, make a small change, and then check the document back in. I find the website interface to be quite clunky for stuff like this, largely because I use firefox (bad with sharepoint) and keyboard launchers (instead of mousing around.) Is there anyway to make a shortcut I can just run to checkout a specific sharepoint document without going through the web browser? Am I better off using Colligo Contributor or similar software to accomplish this? Can anyone recommend any software Sharepoint clients?

  Read the article

• Can't ping IPs for devices not part of Windows Domain

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The DNS server is on a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. All machines either have a fixed or DHCP allocated IP on the 192.168.0.* subnet. How do I configure the DNS server or the Windows Domain so that Windows machines can see the iPhones?

  Read the article

• How to route all traffic over site to site VPN tunnel?

  - by Hutch

  I have a site to site VPN configured between our main site (Site A) and a remote site (Site B). Site A is 10.60.0.0/16 Site B is 192.168.99.0/24 The firewall in Site B is a Juniper SSG running ScreenOS 6.3 and I'm using a route based VPN. The tunnel works perfectly in that from Site A you can reach 192.168.99.0 via the tunnel, and from Site B you can reach 10.60.0.0 via the tunnel. However, we want it so that if you're in Site B and want the Internet it goes via the firewall at Site A, and right now on the Juniper 0.0.0.0 has the ISP router as next hop. My understanding is that on the Juniper, I can set a route for the /32 public IP at our main site that the VPN tunnel connects to to the ISP router via ethernet0/0 (the SSG's external interface), and then modify the 0.0.0.0 route to use our main site firewall via tunnel.1 (the VPN tunnel). Not sure I've explained that so well but is my understanding correct? Thanks

  Read the article

• setting up bridged adapter for VPN server

  - by B. VB.

  I have an Ubuntu linux Linode server that I am trying to install OpenVPN on. I'm following the tutorials (which, it turns out, are quite incomplete). auto br0 iface br0 inet static address 192.168.0.10 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off When I add this chunk in my /etc/network/interfaces, and I restart networking, my eth0 interface does not have an IP and I cannot get on the network (I need to use a buggy, slow, and annoying AJAX term to do damage repair). Why does adding this screw everything up? Any tips on how to set up this bridged adapter?? Thanks in advance!

  Read the article

• ata error: UnrecovData Handshk

  - by Aaron Digulla

  I just saw this message in my log (openSUSE 11.3, Linux 2.6.36.2): ata6.00: exception Emask 0x10 SAct 0x1 SErr 0x400100 action 0x6 frozen ata6.00: irq_stat 0x08000000, interface fatal error ata6: SError: { UnrecovData Handshk } ata6.00: failed command: WRITE FPDMA QUEUED ata6.00: cmd 61/58:00:9f:69:00/00:00:00:00:00/40 tag 0 ncq 45056 out res 40/00:04:9f:69:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) ata6.00: status: { DRDY } ata6: hard resetting link ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata6.00: configured for UDMA/133 ata6: EH complete Two questions: Which disk caused the error? I search /sys and /proc but couldn't find a way to map ata6 to a device (/dev/sdaXY) When such an error happens, does Linux retry the disk operation? Or do I have a corrupt filesystem?

  Read the article

• How anti-virus on the host machne affects performance of virtual machines?

  - by Ladislav Mrnka

  I'm diagnosing some issue with Oracle virtual box where virtual machine sometimes perform terribly slow (much slower then notebook with worse configuration): Notebook i7 (2 cores with HT = 4 logical CPUs), 4GB RAM, 5400 rpm disk, Win 7 64bit Virtual machine (Oracle Virtual Box) Host: i7 (4 cores with HT = 8 logical CPUs, 12 GB RAM, system runs from SSD, virtual machine from 7200 rpm disk, Win 7 64bit) Virtual machine: 4 cores assigned, 8 GB RAM assigned, Win 2008 R2 Enterprise (64 bit) Virtual machine uses bridge to separate network interface (machine has two) VPN for network communication No other virtual machine runs on the host Host has installed ESET Smart Security All SW is updated with last version. My question is if anti-virus on the host machine can somehow affect performance of the virtual machine and if so how can I turn it off without turning the anti-virus itself?

  Read the article

• Website filtering for OpenVPN clients

  - by Asche

  I am currently trying to block some websites by their domain names for all the clients of my OpenVPN server. My first idea was to use the /etc/hosts file. But, its effects seem to be limited to the host only and not to be taken in consideration by OpenVPN. I then tried to configure bind9 and to interface it with OpenVPN, but that solution was unsuccessful and uneasy to use. After this, I considered using iptables to drop all the packets from/to those websites but that forum thread made me thought otherwise since iptables' behavior with FQDN may generate complex issues. Have you got a solution to block websites for all clients using an OpenVPN server on which I am root?

  Read the article

• How should I troubleshoot a problematic wireless connection on Linux?

  - by Gearoid Murphy

  I recently purchased a netgear 150 usb wireless dongle for use with my 11.10 Xubuntu amd64 system. Using the network-manager interface, I can see local wireless networks and enter the authentication details for my local wireless lan. Unfortunately, the connection does not seem to work, I keep getting notifications that my wireless has disconnected (but none indicating that I've connected). When I examine syslog, it seems to indicate that I've successfully associated with the wireless switch and that dhcp has successfully acquired an ip address but the log shows that the dhcp process keeps sending requests, eventually dropping the connection. 'ifconfig wlan0' never shows the dhcp address logged in syslog. I suspect that the problem lies with the usb dongle, my configuration or the wireless switch but I am not certain how to isolate the problem, can anyone provide some insight on how I should go about homing in on the cause of this problem or verifying the functionality of the individual components, thanks.

  Read the article

• What are best monitoring tool customizable for cluster / distributed system?

  - by Adil

  I am working on a system having multiple servers. I am interested in monitoring some server specific data like CPU/memory usage, disk/filesystem usage, network traffic, system load etc. and some other my process specific data. What are available open source that can serve my purpose? If it provides to customize the parameter to be monitored and monitor your own data by creating plugin / agent. Any suggestions? I heard of Nagios, Zabbix and Pandora but not sure if they provide such interface.

  Read the article

• How do ISPs/Colocation Facilities limit bandwidth for Ethernet Drops?

  - by Kyle Brandt

  I have switch providers and have run into some problems with bandwidth limitations. I have more bandwidth then before, but there are performance issues. The router is connected to a 100mBit port, but they limit it to arbitrary settings (in software I imagine). It seems when I go above the limit, the provider starts to drop packets beyond the limit (This is what they said they do as well). Is it possible the previous provider did something like queuing packets above the this limit before dropping them? Is anyone aware of not only what can be done, but what is typical? Also, is there anything I can do on my Cisco router to help this situation? It would seem I am pretty helpless if the packets are dropped before they reach my interface (The traffic that is high is inbound to my network).

  Read the article

• Configuring Wireless Network

  - by Vinod K

  I have vyataa router on VMware with 2 interfaces eth0 and eth1 eth0 is facing the internet eth0 is in Nat mode with dhcp on eth1 is in bridged mode with my ethernet with ip 10.0.2.34/24 The ethernet card is at ip 10.0.2.95/24 i have defined the nat rule. Hence internet is available at eth1 too. Now i am connecting a wireless router at "eth1" iball router, I have connected the router using a cable to the ethernet interface of my laptop. I have configured the WAN connection type as "Static IP" and given "10.0.2.34/24" All the clients that connect using wireless router cannot connect to the internet though. Could anyone provide me a solution for this.. Thank You!!

  Read the article

• How do I revert back to official Linksys firmware from dd-wrt on WRT56G2 v1?

  - by Chris Moore

  I've been having trouble with dd-wrt on my Linksys WRT56G2 v1 router and want to go back to the stock Linksys firmware for it. The router has only 2MB of flash memory, and so I'm running the 'micro' version of dd-wrt. My question is what is the best way to do that? I could use the http://router/Upgrade.asp dd-wrt "firmware upgrade" web interface to do it, in which case there's a dropdown menu choice for "After flashing, reset to": "don't reset" or "reset to default settings". Which should I pick? Some people say that I should use a program called tftp.exe instead. I can probably gain access to a Windows machine if this is necessary. Which of these is the way to proceed? I don't want to brick the router if at all possible! Note: I used the 'wrt54g' tag because I wasn't allowed to create a 'wrt54g2' tag due my low rep here.

  Read the article

• Enterprise online backup providers

  - by PHLiGHT

  We've used Iron Mountain's LiveVault service but found that it was only good for file level backups. We liked how it backed up every 15 minutes. It doesn't support Exchange 2007-10 and the web interface was very poor. Who else is everyone using? The most notable names in online backup such as Mozy and Carbonite don't really seem suitable for larger companies. We have SQL, Exchange and Sharepoint servers and are looking to virtualize in the near future. Until then bare metal restore capability would be nice. We are currently using Backup Exec 12.5 but that can be so troublesome at times. We have about 2 TB of data. 1TB is archival data.

  Read the article

• How to copy Netscape email

  - by Olav

  I think I have the Netscape mail-directory from old computer, how do I copy it to new computer? (Netscape 7.1 Mail, Thunderbird or Seamonkey). I think I have the files in Olduserbackup\xjuwtwtb.slt\Mail I create a new mail account with server pop.superuser.com, and find a directory with that name in C:\Users\myusername\AppData\Roaming\Mozilla\Profiles\default\ou6umlif.slt\Mail I replace the files with those from the backup, but Netscape still shows pop.superuser.com in its interface. Is there some kind of registry setting somewhere I will have to change?

  Read the article

• Suggestions on providing HA access to an external (fibre) RAID subsystem

  - by user145198

  We are looking at upgrading our storage capacity with an external RAID subsystem that has redundant (2) fibre controllers, each controller has 4 x 8 Gbps fibre ports. I would like to make access to this storage system occur via HA Linux. Ideally I would connect 2 fibre ports from each controller into each Linux server, and then export either NFS or iSCSI via a 10 Gbe interface. I have seen plenty of references to DRBD, however all of those references tend to use block storage that is solely attached to each machine, rather than having a shared block storage device, so I am unsure if DRBD could (or should) be used in this case. Ideas?

  Read the article

• How to set my Ubuntu account to super user at all times?

  - by iaddesign

  I have the latest Ubuntu installed and I'll be the only one using it off the network. My question is: how can I make myself super user at all times? Because when I try to delete a file it says I don't have privileges to do so. I know you are going to say it's a security risk but I'm off the network and want to learn all that I can. I don't want to delete the files through the terminal but want to do it through the user interface/explorer. I've installed LAMP and can't copy my site to the www directory. I've tried to remove the preinstalled index file and it won't let me.

  Read the article

< Previous Page | 344 345 346 347 348 349 350 351 352 353 354 355  | Next Page >