Search Results

Search found 26263 results on 1051 pages for 'linux guest'.

Page 351/1051 | < Previous Page | 347 348 349 350 351 352 353 354 355 356 357 358  | Next Page >

• Download - Upload is too slow on Centos

  - by Mehdi

  My download/upload in server and out of server is too slow (around 50 KB/s !) ! Did I miss some configuration ? Some information: CentOS release 6.3 uptime load average: 0.17, 0.32, 0.37 Memory free -m total used free shared buffers cached Mem: 24009 21988 2021 0 806 18098 -/+ buffers/cache: 3083 20926 Swap: 4095 28 4067 lshw -C network *-network description: Ethernet interface product: 82574L Gigabit Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 00 serial: 00:25:90:70:17:4a size: 100MB/s capacity: 1GB/s width: 32 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=off broadcast=yes driver=e1000e driverversion=1.9.5-k duplex=full firmware=2.1-2 ip=108.175.8.123 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:16 memory:fb900000-fb91ffff ioport:e000(size=32) memory:fb920000-fb923fff ethtool ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off MDI-X: off Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000001 (1) Link detected: yes dmesg |grep e1000e dmesg |grep e1000e e1000e: Intel(R) PRO/1000 Network Driver - 1.9.5-k e1000e: Copyright(c) 1999 - 2012 Intel Corporation. e1000e 0000:02:00.0: Disabling ASPM L0s e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 e1000e 0000:02:00.0: setting latency timer to 64 e1000e 0000:02:00.0: irq 33 for MSI/MSI-X e1000e 0000:02:00.0: irq 34 for MSI/MSI-X e1000e 0000:02:00.0: irq 35 for MSI/MSI-X e1000e 0000:02:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:70:17:4a e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: Unsupported Speed/Duplex configuration e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: Disabling ASPM L1 e1000e 0000:02:00.0: eth0: changing MTU from 1500 to 9000 e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO

  Read the article

• Why isn't "(ulimit -d 1000; firefox) &" working?

  - by MaxB

  I'm trying to limit the memory usage of firefox to prevent it from stalling the whole system with problematic web sites. I tried, in bash: (ulimit -d 1000; firefox) & This should limit the memory usage to 1000kB. Then I opened YouTube, and noticed, in top, that firefox is using 2.6% of the memory, or about 200MB, and not crashing. Clearly the limit is being ignored. Why is that, and how can I enforce it correctly?

  Read the article

• bash : "set -e" and check if a user exists make script exit

  - by Dahmad Boutfounast

  i am writing a script to install a program with bash, i want to exit on error so i added "set -e" in the beginning of my script. the problem is that i have to check if a user exists inside of my script, to do this i am using "grep "^${USER}:" /etc/passwd", if the user exists, the script runs normally, but if the user doesn't exist, this command exists, and i don't want to exit on this case (i have to create the user and continue my installation). so what's the solution to make my script continue running ?? i tried to redirect the output of "grep" to a variable, but i still have the same problem :( thanks.

  Read the article

• How do I enable SELinux when booting from a CD/DVD?

  - by JeffG

  I have a bootable DVD which boots the same Kernel as the Hard Drive (which uses SELinux). I have copied /etc/selinux and all the kernel modules to my ramdisk, and have tried both selinux=1 and selinux 1 as Kernel boot parameters. After the system boots, I check dmesg: % dmesg | grep -i selinux Kernel command line: initrd=idrd.img ramdisk_size=110476 selinux=1 SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability SElinux: Registering netfilter hooks But SELinux isn't running: % /usr/sbin/getenforce Disabled % /usr/sbin/setenforce 1 /usr/sbin/setenforce: SELinux is disabled /var/log/messages does not hold any clues. /proc/kmsg also has nothing

  Read the article

• How to keep variable preserve while running script through ssh

  - by Ali Raza

  I am trying to run while loop with read through ssh: #!/bin/bash ssh [email protected] "cat /var/log/syncer/rm_filesystem.log | while read path; do stat -c \"%Y %n\" "$path" >> /tmp/fs_10.10.10.10.log done" But the issue is my variable $path is resolving on my localhost where as I want to resolve it on remote host so that it can read file on remote host and take stat of all folder/files listed in "rm_filesystem.log"

  Read the article

• OpenVPN bad source address from client

  - by Bogdan

  I have one problem with OpenVPN. There are a lot drops records in the openvpn log file on the server: Mon Oct 22 10:14:41 2012 us=726541 laptop/???:1194 MULTI: bad source address from client [192.168.1.107], packet dropped grep -E "^[a-z]" server.conf ----- port 1194 proto udp dev tun ca data/ca.crt cert data/server.crt key data/server.key dh data/dh1024.pem tls-server tls-auth data/ta.key 0 remote-cert-tls client cipher AES-256-CBC tun-mtu 1200 server 10.10.10.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" client-to-client client-config-dir /etc/openvpn/ccd route 10.10.10.0 255.255.255.0 keepalive 10 120 comp-lzo persist-key persist-tun max-clients 5 status /var/log/status-openvpn.log log /var/log/openvpn.log verb 4 auth-user-pass-verify /etc/openvpn/verify.sh via-file tmp-dir /tmp script-security 2 ----- cat ccd/laptop ----- iroute 10.10.10.0 255.255.255.0 ----- cat client.conf ----- remote server ip 1194 client dev tun ping 10 comp-lzo proto udp tls-client tls-auth data/ta.key 1 pkcs12 data/vpn.laptop.p12 remote-cert-tls server #ns-cert-type server persist-key persist-tun cipher AES-256-CBC verb 3 pull auth-user-pass /home/user/.openvpn/users.db ----- According to "Jan Just Keijser - OpenVPN 2 Cookbook" root of the problem is incorrect config options.see the screenshot But, as you see, my config has such options. Could you please help me to solve this problem. @week Verb leverl=6; client log. Mon Oct 22 16:06:02 2012 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Mon Oct 22 16:06:02 2012 /sbin/ifconfig tun0 10.10.10.3 pointopoint 10.10.10.5 mtu 1500 Mon Oct 22 16:06:02 2012 /sbin/route add -net xxxx netmask 255.255.255.255 gw 192.168.1.1 Mon Oct 22 16:06:02 2012 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 10.10.10.5 Mon Oct 22 16:06:02 2012 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 10.10.10.5 Mon Oct 22 16:06:02 2012 Initialization Sequence Completed cat ccd/latop iroute 10.10.10.0 255.255.255.0 ifconfig-push 10.10.10.3 10.10.10.5

  Read the article

• Tomcat: how to change location of manager and host-manager to a subdirectory

  - by rolandpish

  Hi there. I'm running a Tomcat 6.0.28 at port 8080 in a Debian Squeeze box. I'm a newbie in tomcat. I would like to change the location of manager and host-manager applications. That is, instead of going to: http://myserver:8080/manager/html I would like that to be: http://myserver:8080/somesubdirectory/manager/html Is this possible? If yes, how can I achieve this? I would really appreciate any help in this. I've been trying to change the context of /etc/tomcat6/Catalina/localhost/manager.xml from /manager to /somesubdirectory/manager with no success. Also I tried to create a symlink under /var/lib/tomcat6/webapps/ROOT/somesubdirectory/manager with no success. Thanks in advance. Cheers.

  Read the article

• USB resets with Ubuntu 9.10

  - by Grumbel

  Since the upgrade to Ubuntu 9.10 I have issues with getting USB device resets on my Maxtor OneTouch USB harddrive: Nov 9 20:54:37 localhost kernel: [32459.100021] usb 2-2: reset high speed USB device using ehci_hcd and address 4 Nov 9 21:54:37 localhost kernel: [36059.100017] usb 2-2: reset high speed USB device using ehci_hcd and address 4 Nov 9 23:24:37 localhost kernel: [41459.112025] usb 2-2: reset high speed USB device using ehci_hcd and address 4 The device itself continues to work fine, the resets however wake the device out of its sleep state and thus cause it to spin up, which is very annoying. Interestingly, as the log shows, the resets happen at pretty regular intervals (i.e. one hour or half an hour), not randomly. An USB card reader seems to have the same issues, while another USB harddrive from a different manufactor works fine on the same PC. What could be causing this and how could I fix it?

  Read the article

• Diagnosing SAN connectivity issues (RHEL5)

  - by Matthew

  We are currently utilizing GFS2 to share a SAN LUN between 3 servers. However due to a feature problem with vendor software we are using, we currently have the volume unmounted on two of the boxes, and are instead exporting the GFS2 filesystem via NFS from the first one (the software requires some weird locking mechanics that GFS2 doesn't support). As of this morning, NFS was no longer able to read/write to the volume from any of the servers, including the NFS server. I then tried checking the normal mount (the directory that is exported on the NFS server) and I received a weird input/output error just trying to CD into it. When I tried running multipath, I got a DM error, however multipath -l worked just fine. I tried unmounting the GFS2 volume, and the CLI hung. I ran init 0 which killed most services, but then the shutdown appeared to have been hung. I logged in via out of band access (hp ILO) and saw that the shutdown was hung trying to unmount GFS2 volumes. My main priority was getting the box back online so after about 5 minutes of waiting I did a hard reset. I am now trying to figure out what went wrong. What are the correct logs to investigate? I've never run into SAN issues like this before. The SAN is connected via 2 fibre connections. Any help would really be appreciated. Everything appears to be up and functional now.

  Read the article

• sudo midnight commander

  - by mit

  I sometimes start midnight commander as superuser with the command sudo mc to do some operations on the current working directory as superuser. But this results in ~/.mc having the wrong permissions, which I need to fix manually. Any solution? Edit: I accepted an answer. I want to further add, that .mc is a directory, so my solution goes like this: $ cd ~ ~$ sudo chown -R mit.mit .mc ~$ chmod 775 .mc ~$ cd .mc ~$ chmod -R 664 .mc ~/.mc$ chmod 775 cedit It seems not to be a good idea after installing mc to use sudo on its first start .

  Read the article

• How do I send mail from Tripwire using SMTP?

  - by ThomasG33K

  I have just installed tripwire using Ubuntu repos and have gone into the configuration files and changed everything to what I want. When in comes to the options for SMTP mail method and the server and port to use, I am stumped. When I run the test email I get this error message. /usr/sbin/tripwire --test --email blah@nowhere Sending a test message to: blah@nowhere ### Error: The SMTP connection could not be established. ### Server: localhost ### Exiting... Email test failed. I have made appropriate changes to the firewall. I don't have an smtp server installed. Do I need to? Any other ways I could use without installing an SMTP server due to security issues?

  Read the article

• Monitor ssh on non-default port with Nagios

  - by obvio171

  I just deployed Nagios on a Gentoo server and everything is fine except ssh, which it marks as "CRITICAL" because it's refusing connections. But that's because it's running on a port different from the default 22. How do I change it so that it monitors the right port?

  Read the article

• OpenVPN: ifup tap0 drops all connections

  - by raspi

  I'm trying to create star shaped "virtual" LAN with OpenVPN which is not connected to physical network. ie. tap0 packets should not go to eth0. Packet should only go through OpenVPN to connected clients. This setup works with my OpenVPN testing machine which runs Virtual Box but not on my actual server which is running on top of Xen. Both servers are running Ubuntu Intrepid. /etc/network/interfaces: iface tap0 inet manual address 10.10.10.1 netmask 255.255.255.0 gateway 10.10.10.1 /etc/openvpn/server.conf mode server tls-server port 1194 proto udp dev tap client-to-client ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/servername.crt key /etc/openvpn/easy-rsa/keys/servername.key dh /etc/openvpn/easy-rsa/keys/dh384.pem ifconfig-pool-persist ipp.txt server-bridge 10.10.10.1 255.255.255.0 10.10.10.128 10.10.10.250 push .route 10.10.10.1 255.255.255.0 keepalive 5 60 comp-lzo persist-key persist-tun status /var/log/openvpn-status.log log-append /var/log/openvpn.log verb 3 user nobody group nogroup ifup tap0 on Virtual Box: everything ok, SSH keeps running. But on Xen SSH connection drops and I have to reboot whole machine. What I'm missing?

  Read the article

• Easy way of daemonizing in CentOS 5.4

  - by Saif Bechan

  I know there is a program called upstart that can make it easy to make small daemons. I can't get this program to configure on CentOS. I get all sort of errors concerning pkg-congfig, libnih, and dbus. I am working on a node.ja application and this is a pain to start and stop all the time, so I want to create a deamon for this which makes it easy to start and stop.

  Read the article

• smartctl or hddtemp for xvda [on hold]

  - by HST

  I'm trying to check the state of the drives on a remote server running Debian wheezy. I'm using a software RAID10 on top of, I guess, xen, since the entries in /dev are /dev/xvda and /dev/xvdb But it I try smartctl -a /dev/xvda I get /dev/xvda: Unable to detect device type Smartctl: please specify device type with the -d option. I've tried various device type guesses, none work Similar problem with hddtemp, which reports ERROR: /dev/xvda: can't determine bus type (or this bus type is unknown) I've searched the smartmontools documentation, but can't find any discussion of virtual disks. . . How do I get behind the virtualisation to something smart tools or hddtemp can work with?

  Read the article

• GNU screen - Unable to reattach to screen after lost connection

  - by subhashish

  I was using irssi in screen but lost connection. After I ssh'd back in to the server, I can no longer attach to that screen. screen -ls shows that the screen is already attached. I tried screen -D to force detach it, and it said detach but screen -ls still says it's attached. I tried screen -x and it just hangs there. [sub@server ~]$ screen -ls There are screens on: 4033.poe (Detached) 7728.irssi (Attached) 2 Sockets in /var/run/screen/S-sub. What can I do now?

  Read the article

• Passive Scan using wpa_supplicant-0.7.3

  - by Ashish Yadav

  I am using wpa_supplicant-0.7.3 and WL12xx TI Driver(WiFi) . Looking into both code,I seen that both support passive scan . Also, nl80211 driver is used (not wext). I am not able to find any command for passive scan in wpa_cli . With iw , for passive scan we can use : iw dev wlan0 scan passive Similar I want to do passive scan using wpa_supplicant . So need help to know how to do passive scan using wpa_supplicant?

  Read the article

• "Must have" "Launcher" applications?

  - by levi rosol

  What applications do you use for quickly launching applications, websites, folder paths, etc? Post one application per response, and include a URL.

  Read the article

• Disk full, du tells different. How to further investigate?

  - by initall

  I have a SCSI disk in a server (hardware Raid 1), 32G, ext3 filesytem. df tells me that the disk is 100% full. If I delete 1G this is correctly shown. However, if I run a du -h -x / then du tells me that only 12G are used (I use -x because of some Samba mounts). So my question is not about subtle differences between the du and df commands but about how I can find out what causes this huge difference? I rebooted the machine for a fsck that went w/out errors. Should I run badblocks? lsof shows me no open deleted files, lost+found is empty and there is no obvious warn/err/fail statement in the messages file. Feel free to ask for further details of the setup.

  Read the article

• Is there any way to use the xscreensaver gltext to monitor system information?

  - by Shane

  I am trying to get the X screensaver gltext to monitor my system temp and maybe some other stats. Writing a script that puts together the stats periodically is no problem, but the main thing I'm running into is that gltext doesn't refresh - whatever text I feed it stays there. So, for example, I run this command: $ /usr/lib/xscreensaver/gltext -text "`cat /proc/acpi/thermal_zone/THRM/temperature`" and get a gltext window showing: temperature: 60 C I can manipulate it and format it as necessary, but as my CPU heats up and cools down, it doesn't update, even if I include time variables that do. I have a script that feeds gltext the time as the first line and the temp as the second line - and although the time updates continuously as the time changes, the temperature value remains the same as whenever the screensaver started. Is it possible to do what I want, which is change the text every 60 seconds if the temperature changes?

  Read the article

• Which server software and configuration to retrieve from multiple POP servers, routing by address to correct user

  - by rolinger

  I am setting up a small email server on a Debian machine, which needs to pick up mail from a variety of POP servers and figure out who to send it to from the address, but I'm not clear what software will do what I need, although it seems like a very simple question! For example, I have 2 users, Alice and Bob. Any email to [email protected] ([email protected] etc) should go to Alice, all other mail to domain.example.com should go to Bob. Any email to [email protected] should go to Bob, and [email protected] should go to Alice Anything to *@bobs.place.com should go to Bob And so on... The idea is to pull together a load of mail addresses that have built up over the years and present them all as a single mailbox for Bob and another one for Alice. I'm expecting something like Postfix + Dovecot + Amavis + Spamassassin + Squirrelmail to fit the bill, but I'm not sure where the above comes in, can Postfix deal with it as a set of defined regular expressions, or is it a job for Amavis, or something else entirely? Do I need fetchmail in this mix, or is its role now included in one of the other components above. I think of it as content-filtering, but everything I read about content-filtering is focussed on detecting spam rather than routing email.

  Read the article

• clear smartctl log

  - by MA1

  Is there any way to clear/remove the smartctl test results log?

  Read the article

• Mod_security questions and on User-Agent types

  - by Tiffany Walker

  Very new to mod_sec I want to block a UA string and I noticed there are a few types: SecRule HTTP_User-Agent SecRule REQUEST_HEADERS:User-Agent What is the real difference between them? My block: SecRule REQUEST_HEADERS:User-Agent "perl" "phase:2,pass,msg:'Perl based user agent identified'" Do I need to set a SecDefaultAction phase:2,deny,status:403,log,auditlog before that? Then any SecRule below that follows that action right?

  Read the article

• Java issues with Apache 2.0 Agent 2.202 for RHEL5 Linux 64bit

  - by Richard

  In trying to install Apache 2.0 Agent 2.202 for RHEL5 Linux 64bit, the dialogue appears as follows. $ ./setup Error : java is not present in path. Please enter JAVAHOME path to pick up java:/usr/lib/jvm/java-1.6.0-openjdk-1.6.0.0.x86_64/jre/ Launching installer... Attach to native process failed $ ./setup Error : java is not present in path. Please enter JAVAHOME path to pick up java:/usr/lib/jvm/java-1.6.0-openjdk-1.6.0.0.x86_64/jre/lib ./setup: line 80: [: 107:: integer expression expected ./setup: line 83: [: 107:: integer expression expected Error : Incorrect java version (1.2.2 or above is needed). Please enter JAVAHOME path to pick up java: On the server we have the following JREs and I've tried both. $ sudo rpm -qa | egrep "(openjdk|icedtea)" java-1.6.0-openjdk-1.6.0.0-1.27.1.10.8.el5_8 $ find 2>/dev/null | grep -i '/jre/' ./usr/lib/jvm/java-1.4.2-gcj-1.4.2.0/jre/bin/ ... ./usr/lib/jvm/java-1.6.0-openjdk-1.6.0.0.x86_64/jre/ Any suggestions? I know I'm overlooking something. In previous searches I've only found one other posting that comes close but it has no responses (http://forum.parallels.com/showthread.php?t=76556).

  Read the article

• Running git-svn with cron results in garbage in .git

  - by Paul

  I've setup a git-svn repo with cron to fetch from the svn repo daily. I have a script to do the fetching, and this is what is invoked by cron. Everything is fine with the repo, and the script works fine when executed manually. However, when it runs under cron, empty files get dropped into the .git directory. The files have names that look like they are some base64 output, e.g. juTrvjP6m8 and kcKf3hu3b4. Two of these files show up for every cron run. I thought these might be commit hashes, but they're not, git-show says it's an unknown revision. I set-up the repo as follows: git svn init http://svn.ip.addr/repo git svn fetch svn-remote My script looks like this: cd /gitsvn/dir git svn fetch svn-remote git svn push pub The last line pushes the repo to a separate (bare) public repo from which others can clone. I'm piping the output from the cron job to a file, which looks like this: fatal: unable to run 'git-svn' Counting objects: 21, done. Delta compression using up to 2 threads. Compressing objects: 100% (10/10), done. Writing objects: 100% (11/11), 59.08 KiB, done. Total 11 (delta 8), reused 0 (delta 0) To /gitpub/repo.git 360faf5..a153b0d trunk -> trunk The line "fatal: unable to run 'git-svn'" is alarming, but the fetch seems to go ahead anyway. Any suggestions? Where are these empty garbage files coming from, and how to stop them? Am I in for bigger problems in the future? BTW, I'm using git 1.6.3.3.

  Read the article

< Previous Page | 347 348 349 350 351 352 353 354 355 356 357 358  | Next Page >