Search Results

Search found 10852 results on 435 pages for 'tool'.

Page 363/435 | < Previous Page | 359 360 361 362 363 364 365 366 367 368 369 370  | Next Page >

• Troubles Installing Windows 7 via USB. Flat install?

  - by Brian

  Hi friends, I've been struggling with this for a while. Windows 7 64-bit Enterprise edition just will not install on my Shuttle K45 system via a USB key. It hangs out during the install while copying files or while creating the partitions. The system is pretty standard and low-tech: IDE hard drives, no CD, 2G RAM. I am not sure what of the problem. Other than the Shuttle, I have a Apple MacBook Pro. On the MPB, I am running OS X, and Mint Linux and Window XP over Parallels. I have an ISO of Win7 that works (I installed it as a Parallels VM to make sure). I have used UltraISO and MS Windows 7 USB/DVD Download Tool to write it to the 8G USB key. Both seem to copy all the files correctly (with UltraISO, I asked it to verify). It boots via USB and the install looks just fine. Until it hangs, most of the time with a copying error of 0x80070241. So now I am trying to figure out if there are other ways I can install Windows 7 on this Shuttle system that has no CD drive. I've heard about a flat installation, however those all seem to be doing something from within Windows. I do have access to a command prompt from the Windows 7 install. Does anyone know if/how I can prep the Shuttle hard drive with Windows 7 installation and have Windows 7 install from the hard disk. I do not have an external enclosure for the IDE HD and I do not have any other system I can hook up to the hard drives. I do have an external Maxtor OneTouch drive available.

  Read the article

• Linux RAID: Replacing Failed Drive...permanantly

  - by user137519

  Okay, odd question here. I have a server with RAID 5. A drive failed, in a really physically in a really odd way. On the machine it boots and is seen by the BIOS but...no partition can be seen on the drive consistantly (in and out). 2 out of 3 drives working...I made new spare disk and added it, RAID 5 rebuilt clean. All appears well but...when I reboot it keeps trying to use the 2nd drive which doesn't give any partition data, so of course the RAID 5 gets 2 out of 3...again. The status of my drive is as follows: /dev/sda2:Good /dev/sdb2 (drive has physical problem so no partition data) bad, /dev/sdc2:good /dev/sdd2:good. Every time I reboot the mdadm system seems to keep trying to use /dev/sdb which has physical failure (although spins and is detected). /dev/sdd is the new drive I created. I added /dev/sdd to the raid and it rebuilds the raid but this action isn't memorized upon reboot so it keeps listing /dev/sda and /dev/sdc but doesn't use the perfectly good /dev/sdd until I re-add manually. I've tried removing the dead drive with the mdadm tool, but as it cannot see /dev/sdb paritions it will not fail or remove it (says partition doesn't exist). the /etc/mdadm.conf was automatically made on the original OS install which only lists: DEVICE partitions MAILADDR root ARRAY /dev/md2 super-minor=2 ARRAY /dev/md0 super-minor=0 ARRAY /dev/md1 super-minor=1 Basically just the raids to use on boot. I need to remove this semi-dead drive (/dev/sdb) but I'd prefer to know why this is happening before I do. any ideas or suggestions. I supposed I could attempt to clone/replace /dev/sdb (the partitions on drive show up, then disappear shortly after) but given the partition "chester cat" behaviour this seems risky to me and as I have a working "spare" it seems unnecessary. Thanks in advance for your insight.

  Read the article

• Half of installed RAM is hardware reserved

  - by user968270

  After a rather arduous and convoluted series of problems that left me without a desktop for ~80 days, I've finally got the thing up and running, having replaced the power supply, motherboard, graphics card and CPU. Now, however, I'm experiencing the 'hardware reserved RAM' issue. Perhaps this is the exhaustion talking, but looking at the question that tends to get pointed to when this kind of topic gets locked as a duplicate hasn't helped. I have 16 GB of RAM installed in an MSi 970A-G46, which is spec'd for up to 32 GB of RAM. The BIOS recognizes that I have 16 GB installed, and the resource monitor also shows the whole 16 GB, only it shows 8 GB as hardware reserved. I've seen suggestions that it's an OS issue, but the particular installation of Windows 7 (64-bit) which I'm running on my boot drive is the same as the one that could actually access the 16 GB in my previous motherboard (MSi 870A-G54). I've updated my BIOS using the MSi Live Update tool and restarted the machine with no effect, and I cannot seem to locate any 'Memory Remapping' option as I've seen mentioned. I've physically swapped the RAM between the slots to no effect. I've unchecked the Maximum Memory box in the msconfig Boot tab's advanced options, also to no effect. These are my system's basic specifications OS: Windows 7 Home Premium (64-Bit) Motherboard: MSi 970A-G46 CPU: AMD FX-8150 Graphics Card: XFX Radeon HD 6870 Boot Drive: OCZ Agility 3 Storage Drive: Samsung Spinpoint F3 ST1000DM005/HD103SJ 1TB PSU: Thermaltake TR-2 TR600 600W ATX12V v2.3

  Read the article

• Mysql server high trafic makes websites really slow or unable to load

  - by Holapress

  Lately we have been having a lot of problems with our mysql server, from websites being really slow or even unable to load them at all. The server is a dedicated server that only runs our mysql database. i have been running some test using a profiler (JetProfiler) and tool to stress test (loadUI). If I use loadUI to connect with 50 simultaneous connections to one of our websites that runs a resently big query it will already make the website be unable to load. One of the things that makes me worried is that when I look at Jetprofile it always shows a Treads_connected of 1.00 and it seems that when it hits around 2.00 that I'm unable to connect. The 3 big peaks are when I run a test with loadUI, first one was 15 simultaneous connections wich made it still able for me to load the website but just really slow, the second one was 40 simultaneous connections which already made it impossible to load and the third one was with 100 connection which also didn't make it load anymore. Another thing that worries me is that in JetProfiler it says all the queries that get used are full table scans, could this maybe be the problem? The website I run as a test runs 3 queries, one for a menu that outputs around 1000 rows, one for the adds that has around 560 rows and a big one to get posts that has around 7000 rows (see screenshot bellow) I also have monitored the cpu of the server and there seems to be no problem there, even when I make a lot of connections with loadui the cpu stays low. I can't seem to figure out what is the main cause of the websites being unable to load when there is a high amount of traffic, if anyone has other suggestions for testing or something that might cause the problem please let me know.

  Read the article

• MySQL stopped asking for passwords

  - by BlaM

  I'm currently experiencing a weird problem with one of my MySQL database servers: It stopped asking for passwords when I try to access the database from local with the mysql command line tool. I need a valid admin username. I also still need a password for remote access (i.e. from another IP). And I need a password when I - for example - access the database from a PHP script. But when I try to access the database from local host/commandline it will let me straight in to the data with my administrative users. They (admin users) have passwords set - and as I mentioned - I still need to specify those when I try to access the data via PHP. Changing the password didn't help. Non-Administrative users need to specify their passwort, but that doesn't really help if they can get anywhere with "mysql -u root" (or another admin user account name). (System Debian Linux Lenny, MySQL 5.0.51a) Any ideas? Anything that explains this behaviour? I don't understand how this can happen.

  Read the article

• Will a SQL Server client alias survive a sysprep?

  - by shufler

  I want to sysprep a Windows Server 2008 R2 SP1 machine that has SQL Server 2008 R2 SP1 installed (for reference, SQL Server 2008 R2 has a new sysprep feature that allows the instance to be sysprepped). On the server is a SQL Server client alias that points to the default SQL Server database engine instance. For reference, the alias is called Alias-SQLServer and has been configured in both 32-bit and 64-bit cliconfig versions (that is, both registry keys exist) The alias points to the local instance as the image will be used to create development VMs and the installation script for the application that is being developed will use the SQL Server client alias in order to generalize the installation scripts. I can't seem to find information about whether the sysprep tool will update the SQL Server client alias's registry keys with the server's new name once it's unsealed. My guess is that it is not; how is sysprep to know that the server name the alias points to will be different for each image? Right? Perhaps if the alias points to localhost instead of the server name this will work?

  Read the article

• Random “Lost connection to MySQL server at 'reading initial communication packet', system error: 0”

  - by user1606545

  Sometimes I get the error from MYSQL server: Lost connection to MySQL server at 'reading initial communication packet', system error: 0 I cannot find the cause, since most of the time it works, but every week for some hours I get this error. I googled, but there seem to be only users which have this error permanently. But in this case, it only occurs sometimes. I checked hosts.allow and hosts.deny, but the host is allowed and not denied. Also sometimes I get the error: File './database/table.MYD' not found (Errcode: 24) It occurs very rarely. But it occurs for some hours once a week, sometimes on multiple days, but suddenly the problem disappears again. I have checked the open files limit. It's 2048 and should be absolutely enough. I also tried to increase the number of open files nevertheless, but no effect. I thought, perhaps the process does not close some tables. But this is impossible, because after a while everythings o.k. again and the process opens maximum 100 tables at once. I also checked the MySQL-runtime-environment, and there were 930 opened files. I cannot explain that. After a while it's 129. I am running a MySQL-Server on a SUSE-Linux machine. I connect to the MySQL-Server from another host by the command line tool "mysql" and by MySQL-C-connector. The MySQL-Server is version 5.0.67.

  Read the article

• How to copy a floppy boot disk?

  - by Sammy

  I have a floppy boot disk and I would like to copy it to preserve it, as a backup. If I have two floppy drives, A and B, how can I copy the disk? Assuming one has two floppy drives Can I simply insert the floppy disk in one of the drives and then an empty floppy disk in the other and issue a simple command like this one. A:\>copy . b: Will this only copy the contents of the current directory and none of the files in subdirectories? Do I have to explicitly specify the option to copy everything? Also, what about the boot information? That won't get copied, right? If one has only one floppy drive... How do you copy a floppy disk if you only have one floppy drive? Do you in fact have to copy its contents to the local hard drive C and then copy that to an empty floppy disk using the same floppy drive? A:\>copy . c:\floppydisk A:\> A:\>c: C:\> C:\>copy floppydisk a: C:\> I'm guessing I will need some type of disk image tool to really copy everything on a bootable floppy disk. Something like the dd command on Linux perhaps? Am I right?

  Read the article

• Push, parse & import "selected" data, text, info blobs from Webpages/ Emails as Event/ Appointment to standard Calendar directly or as .ics file?

  - by Alex S

  Any tool, plugin, extension, script/ code to push "selected" data, text, information blobs from Web pages, Emails etc, then parsed and imported to structured Event, Appointment (e.g. .ics) on a standard Calendar like Outlook, Google, iCal? If not, what and how could I use some scripting, coding or existing tools, extensions to add on top and do this. I come across a lot of unstructured information on Webpages, Emails, FB events etc. where I just want to add that information to my Calendar. Instead of entering all the information by hand all the time, there should be an easy enough way to have the information get parsed, organized and imported to a Calendar... Either directly to a calendar from source or Translated to a standard format such as .ICS that can be imported & saved easily. Would love to see some suggestions for this incorporating one or more of the following: on Windows with Chrome & Outlook on iPhone/ iPad to its Calendar PS: I'll come back and see if I can add more information to this question and to answer it as well. I have not found a solution yet.

  Read the article

• Read non-blocking from multiple fifos in parallel

  - by Ole Tange

  I sometimes sit with a bunch of output fifos from programs that run in parallel. I would like to merge these fifos. The naïve solution is: cat fifo* > output But this requires the first fifo to complete before reading the first byte from the second fifo, and this will block the parallel running programs. Another way is: (cat fifo1 & cat fifo2 & ... ) > output But this may mix the output thus getting half-lines in output. When reading from multiple fifos, there must be some rules for merging the files. Typically doing it on a line by line basis is enough for me, so I am looking for something that does: parallel_non_blocking_cat fifo* > output which will read from all fifos in parallel and merge the output on with a full line at a time. I can see it is not hard to write that program. All you need to do is: open all fifos do a blocking select on all of them read nonblocking from the fifo which has data into the buffer for that fifo if the buffer contains a full line (or record) then print out the line if all fifos are closed/eof: exit goto 2 So my question is not: can it be done? My question is: Is it done already and can I just install a tool that does this?

  Read the article

• Google Apps, SPF, softfail problem (validates with validation tools, but still softfails otherwise)

  - by mq.chen

  Hi, I guess this is probably a commonly asked and boring question but I'm really at a loss and I don't know what else to do. This might be a duplicate of other questions, but none of the solutions worked for me. I've Googled around and read just about anything I could find but I'm still puzzled as to why it doesn't work. The gist of my problem is that I have set-up Google Apps for a client of mine with the domain fintan.dk. Everthing works just excellent, except emails sent from *@fintan.dk (either with the Gmail web-interface or desktop client) to a non-Google Apps email gets a softfail (I have sent to my University email, an email hosted at MediaTemple and even Hotmail). The emails gets a pass when sent to a Google Apps or Gmail address though... (All emails from that domain are sent via email clients.) So this is what I have done so far: I've added the SPF record Google recommended (v=spf1 include:_spf.google.com ~all), waited several days hoping it would a DNS update delay problem. Now, three days later there is no change. I have verified the settings in the desktop clients several times. I have validated the records with validation tools like the SPF Query Tool, [email protected] and [email protected]. All of them validate and gives a pass, saying there shouldn't be a problem, but strangely there still is. So, I really don't know what else to do. Any help is very much appreciated. Thank you in advance!

  Read the article

• Changing the modified date of a message in Exchange 2010

  - by jgoldschrafe

  My organization is in the middle of a process to move their Exchange 2010 messaging system from one archiving platform to another. As part of this process, we need to restore all archived messages back into users' email accounts, and then let the new system import them again. The problem is that when the messages are dumped back, the modified date on the message is set to the date it was restored, which trips up message archiving and basically means nobody will have anything archived for six months. So you don't have to ask: no, our archiving platform only uses the modified timestamp on the message and cannot be altered to temporarily use the sent or received timestamp instead to determine whether to archive it. We and others have asked for the feature, but it doesn't exist right now. What we're looking for is a method to go through the user's mailbox and alter the modified timestamp of each message (or preferably received more than X months ago) to the received date of the message. We also don't want to spend more on this tool per user than we're spending on the archiving solution in the first place. We've run across a few tools that are something ridiculous like $25 per user. I don't think we're even paying close to that for Exchange and the archiving solution put together. Whatever we settle on should function on a live mailbox with no downtime. Playing around with PST imports and hacky little things like that isn't going to work. We're fine with programming/scripting, if anyone knows the best way through PowerShell, COM automation or some other way to best handle this.

  Read the article

• Application that will identify percentage of your system disk bandwidth used on a user-application by user-application basis?

  - by Warren P

  I always (subjectively) feel my computer is far too slow (however fast it is), and so I'm always looking for ways to measure and understand what my computer is actually doing, that is making it seem "slow" to me. It has been my observation that my software-developer workload is most often disk-bound (I am waiting for Disk I/O) more than CPU bound. What has made it worse, is that I am using a corporate PC that has in-memory active-scanning anti-virus software that I do not have control over, and also some IT department mandated services that seem to suck up a lot of available hard-disk bandwidth. The best tool I have seen (in Windows 7) is the Resource Monitor which I usually acess from the button in the task Manager. The disk IO page, however, seems to label Disk Activity at a very low level (for example, showing the Volume Shadow Storage, which is flushing information obviously written by something ELSE other than VSS itself, and then writes to Pagefile.sys, which are obviously due to Virtual Memory faults in some application). What I would like to know is if a utility exists that can add up all direct disk input and output by user-level process, or find the process or service that caused VM or VSS activity. In that way, I hope, you could establish a real idea of how much of your computer's precious disk subsystem bandwidth is attributable to a particular application. here's a scenario: MyApp.exe writes 100k/s and reads 100k/s directly. VSS ends up writing another 100k/s. pagefaults caused inside MyApp.exe cause another 100k/s of writes. So the total "cost" of MyApp.exe running, during a period of time (let's say 1 second) is 400k/s, whereas you can only directly observe half of that, in Resource Monitor. Is there a smarter disk-IO watching piece of software I can use?

  Read the article

• rsync per-site configuration file?

  - by Scott

  I know how to configure a per-site entry for ssh, but is there any kind of a client configuration for rsync that allows per-site configuration options and aliases or similar shortcuts like the .ssh/config? I'm curious because I have a minimal ssh server installed on my android phone and I also have a minimal rsync tool on it as well. I'm getting tired of having to root login onto the phone and sym-link both tools to standard places the android OS looks for executables as the ssh server is bare bones and has a typical *bear multi-link binary for the basic unix commands (that does not include rsync) I end up having to include --rsync-path=/path/to/rsync/android/files/rsync every time I want to do any rsyncing of the files on my phone, but this path is always the same. I've gotten around it in the meantime with a glob approach in a shell script wrapper, but this sometimes limits the customization I can do with the rsync call. I'm just wondering if there is anything similar to the .ssh/config file where I can create an alias for my phone (e.g. 'android') where specifying rsync android:/mnt/sdcard will automatically assume --rsync-path=/blah/blah/blah --no-g --no-p --no-t etc. Tre`

  Read the article

• How can I get multiple video cards to work on linux?

  - by user17943

  I installed fedora 12. I have 2 ATI cards that I used to use on windows to run 4 monitors. A recurring problem has been to get them detected in linux. Only my secondary card is picked up linux. When I manage the displays it detects the 2 monitors connected that card. What are the specific steps I should take to get the second card detected? Supposedly there is a tool system-config-xfree. I don't have it, yum can't find it. Also I heard it has something to do with editing some xorg.conf file or something to that effect. I have absolutely no idea how to find the "bus id" of my card, or lookup the horizontal refresh rates, etc.. I would probably have no problem following the documentation & editing the file if I knew a good way to find these values. Someone also suggested installing linux twice and saving the xorg.conf it generates each time (with different card each time) and then merging the two by hand. That is like killing a fly with a hammer though, when I do this again and again in the future It'd be nice to not have to take twice as long. Thanks

  Read the article

• Physical Debian to VMWare: vmware-converter, dd-image or otherwise?

  - by Dabu

  we have two debian Lenny production machines, both running larger commercial websites. Now these machines need to be moved, and in the process, they need to be virtualized to VMWare ESX. If you believe the internet information, there are several ways to accomplish this. The easiest for us would be to use our weekly dd backup where the whole disk, however, I have no experience with this kind of technology and if it is really possible. The second best way would be via an application on the source machine virtualizing it and generating an ESX compatible VM. However, the software is beta and unsupported, and after installation, nothing really works (the /etc/init.d/vmware-converter script doesn't actually do anything, start and stop reply with success messages, yet ps shows that there are no new processes). The worst way with the most work would be to install a new machine and set it up manually, copying files and databases as needed. This part is clear in it's execution, and my question(s) do not touch this. Is my 1st way possible? Has anyone done this yet, or better, has a page with instructions? Or is there a help page that explains how to correctly install, run and use the vmware-converter tool using a Debian installation (it's possible that I dod something wrong during installation already)? Thank you.

  Read the article

• USB drive was bootable, but no longer isn't

  - by i-g

  I'm trying to install a new OS onto a computer from a bootable USB stick. I previously installed Ubuntu Linux and it was a piece of cake -- I downloaded the ISO image, used UNetbootin to copy it to the USB drive and make it bootable, and that was that. Now, however, no matter what I try, I can't make the same USB drive bootable again! I've tried formatting it as FAT32 and NTFS. I've tried several different Linux distributions and Windows 7. I've tried using UNetbootin, Windows 7 USB Download Tool, WinToFlash, and manually making it bootable with diskpart/bootsect/bootrec. (Yes, I've tried bootsect /nt60 x: /force.) None of this seems to be working! When I try to boot from the drive, the machine reads from it (I can see the drive's LED blinking) and then gives me the same "Insert system disk and press Enter" message. (I've disabled booting from the hard drive.) Am I missing something I need to do to make the USB drive bootable again? The USB drive in question is a SanDisk Cruzer 8GB SDCZ6. The computer I'm working on is running Windows Vista SP1.

  Read the article

• Are ZFS snapshots + S3 a viable backup system for several VMs and general fileserver storage?

  - by AllanA

  I've been tasked with setting up a backup system for my small office (around 12 people). Most of our production stuff is on the AWS cloud, so what I need to back up are some small office/development files (under 100G right now), plus our operational VMs and development, which round out to a bit under 1T. I just need something reliable, convenient, and straightforward. I'm comfortable with Linux, FreeBSD, and to some extent Solaris 10, so I'm leaning toward a full server rather than an appliance system ala Openfiler or FreeNAS. What I'm contemplating is a small fileserver for general storage and nightly backups of the virtual machines, followed up by an offsite backup to Amazon's S3 storage service. It'd be the usual incremental backups nightly and full backup weekly. My question is if using ZFS snapshots, both locally and dumped to S3 via 'zfs send [-i]', is a viable backup tool? Or should I stick to using Duplicity, or some other method entirely? ZFS snapshots on the internal fileserver/backup machine sound like a perfect way to provide quick and convenient data recovery, so I'm likely to go with that for local redundancy. (If you folks see scenarios where relying on ZFS snapshots would be worse than a more traditional archiving backup, feel free to convince me.) But are snapshots flexible enough to lean on for recovery from the loss of my backup server? Or am I better off with something more traditional? (feel free to recommend free or commercial backup solutions you favor.)

  Read the article

• Server 2008R2 Server Manager Roles and Features won't refresh or allow addition of new roles or features

  - by MattChorba

  I have a standalone DC in an isolated lab. I have installed the SUR tool and found no errors. I ran SFC and found no errors. I have attempted to install Windows Backup feature using Powershell, but received the same error about the computer needing to be restarted. Powershell cmdlets will list all of the installed roles and features. The rest of Server Manager works without problems. What can I do to get Server Manager Roles and Features working properly again? Picture of Error: CheckSUR.log: ================================= Checking System Update Readiness. Binary Version 6.1.7601.21645 Package Version 13.0 2011-11-28 13:20 Checking Windows Servicing Packages Checking Package Manifests and Catalogs Checking Package Watchlist Checking Component Watchlist Checking Packages Checking Component Store Summary: Seconds executed: 413 No errors detected (w) Unable to get system disk properties 0x0000045D IOCTL_STORAGE_QUERY_PROPERTY Disk Cache CheckSUR.persist.log: ================================= Checking System Update Readiness. Binary Version 6.1.7601.21645 Package Version 13.0 2011-11-28 13:20 Checking Windows Servicing Packages Checking Package Manifests and Catalogs Checking Package Watchlist Checking Component Watchlist Checking Packages Checking Component Store Summary: Seconds executed: 413 No errors detected (w) Unable to get system disk properties 0x0000045D IOCTL_STORAGE_QUERY_PROPERTY Disk Cache

  Read the article

• lighttpd on Fedora permission issues

  - by Isaac Gateno

  I'm trying to get started with lighttpd on Fedora 16 to run a RESTful api for development. Right now even with the most basic sample config file I'm getting 404 pages when I know the pages I'm pointing at exist. From reading other questions I'm leaning towards this being a permissions issue, but I'm confused about how lighttpd runs on Fedora. There's a user called "lighttpd" not "www-data"? I can't see this user in the system-config-users tool and I can't su into it to check which permissions it has. I'm trying to point lighttpd to "/var/www/lighttpd" which has some example pages in it. The permissions for the files inside are set to -rw-r--r-- and the permissions for the folder containing them are drwxr-xr-x. Doesn't that mean that any user can view these files? I'm not sure what else I should be checking as I don't have much experience with server configuration. Any help would be appreciated. Edit: I was following the tutorial configuration here so the lighttpd.conf file contains server.document-root = "/var/www/lighttpd/" server.port = 3000 mimetype.assign = ( ".html" => "text/html", ".txt" => "text/plain", ".jpg" => "image/jpeg", ".png" => "image/png" ) and I was just trying to get the basic example page working.

  Read the article

• Change the background color of selected text in Google Docs to increase readability [migrated]

  - by gene_wood

  How can I override or change the background color of text selected in Google Docs? It is difficult for me to see the difference and I would like to increase the contrast or difference. After Google restyled Google Docs last year (or earlier this year), I've been unable to see selected text. It's possible this is a visual deficiency with my eyes. In Google Docs, under both Google Chrome (17.0.963.83 (Official Build 127885) m) and Firefox (11.0), when I select text inside a Google Doc, the selected text has a background of color #d6e0f5. Compare this to the default browser background color of #2f65c0. (I determined the color of the selected text background by taking a screenshot and using the color picker tool in Photoshop). I've tested this using a brand new Firefox profile as well as google chrome profile. Here's a section of a screenshot showing the selected text : I've tried using a userscript to override the CSS to go back to the default text selection color using the "Stylish" plugin with this css : ::selection { background:#2f65c0; color:#ffffff; } ::-moz-selection { background:#2f65c0; color:#ffffff; } ::-webkit-selection { background:#2f65c0; color:#ffffff; } This code works on other sites, but I'm unable to get it to work on Google Docs. (I tested on other sites but applying the userscript to a different domain and using bright yellow instead of the default dark blue #2f65c0.) When you use Google Docs, do you have the same color background for selected text or something different? (To test this, browse to docs.google.com , create a document, type text into the document, select the text with the mouse by dragging over it, take a screenshot, load the screenshot up in an image editor and determine the background color of the selected text.) This color differential (between light blue #d6e0f5 and white #fffff) may be easy to see for others and the problem lies with my eyes.

  Read the article

• LAMP Stack Version Help -- Is there a website or version tracker source to help suggest the right versions of each part of a platform stack?

  - by Chris Adragna

  Taken singly, it's easy to research versions and compatibility. Version information is readily available on each single part of a platform stack, such as MySQL. You can find out the latest version, stable version, and sometimes even the percentage of people adopting it by version (personally, I like seeing numbers on adoption rates). However, when trying to find the best possible mix of versions, I have a harder time. For example, "if you're using MySQL 5.5, you'll need PHP version XX or higher." It gets even more difficult to mitigate when you throw higher level platforms into the mix such as Drupal, Joomla, etc. I do consider "wizard" like installers to be beneficial, such as the Bitnami installers. However, I always wonder if those solutions cater more to the least common denominator -- be all to many -- and as such, I think I'd be better to install things on my own. Such solutions do seem kind of slow to adopt new versions, slower than necessary, I suspect. Is there a website or tool that consolidates versioning data in order to help a webmaster choose which versions to deploy or which upgrades to install, in consideration of all the other parts of the stack?

  Read the article

• S.M.A.R.T. broken sectors

  - by Jeffrey Vandenborne

  Recently I received my hard drive (LaCie) that I've sent away for warranty, my disk failed, and I used Palimpsest Disk utility to check if anything was wrong in the S.M.A.R.T Status. And it said that there were a few broken sectors. So the next day, I went to the store and told the story. 4 weeks later I actually got my drive back. The first thing I did was plugging it in and starting the disk utility, and weirdly it showed me pretty much the exact same things, even the values of most tests were the same as they were before when my drive broke. The serial number is different though, but it does show a very peculiar value. Now I'm wondering, I'm almost sure it's the exact same drive and it still says I've got broken sectors, does it just say that because it has been cached in the drive somewhere while LaCie DID actually fix it? Or should I run the extended self test (which seems to take hours) first? Also I've tried the smartctl command tool, it says the drive has smart support, but it doesn't show anything, it says that it's enabled, but then it says that it's disabled, picture below The picture of the Disk utility: Thanks in advance

  Read the article

• Win 7 crashes, PC reboots and says "Hard drive 0 not found" until I turn if off and on again

  - by Danny T.

  I recently made the move from Windows XP to Windows 7. Since then, when my computer is on for a few hours it always ends up rebooting without warning. Then the BIOS won't recognize my hard drive (hard drive 0 not found). If I turn off my computer and then on again, it boots normally. Some details: Dell Dimension 9150 Windows 7 I updated the BIOS I updated all system drivers with the latest version from Dell (SATA, Chipset, etc.) Other drivers updated too (Graphic card, sound, etc.) There is one thing that I tried after some Googling: I turned off the DMA access to the drives, but it's still rebooting after a few hours. Any clue? UPDATE 2010/12/13 Here are the events from the Event Log for today, from when I turned the computer on until it crashed: 19:17 - Error - ID 10016 - DistributedCom 20:06 - Error - ID 1008 - Customer Improvement Program (could not send data to Microsoft) 21:48 - Critical - ID 41 - Kernel-Power (System was restarted without proper shutdown) 21:48 - Error - ID 6008 - EventLog (Previous system down was not planned) 21:48 - Error - ID 1101 - EventLog (Audit Event ignored) 21:49 - Error - ID 10016 - DistributedCom Both DistributedCom events have a description along these lines (translated from French): The authorisation parameters specific to the application are not allowing Local Execeution for the COM server application with the CLSID {C97FCC79-E628-407D-AE68-A06AD6D8B4D1} and the APPID {344ED43D-D086-4961-86A6-1106F4ACAD9B} to the SID AUTHORITY NT\User System (S-1-5-18) from the address LocalHost (LRPC usage). This security authorisation can be changed with the Component service administration tool. UPDATE 2010/12/31 Here are the error messages I have on blue screens : STOP C000007xA - Kernel_Data_Inpage_Error "Unkown hard error" C00000135 - Can't start because &hs is missing

  Read the article

• Need help toubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after restarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What I have done: I thought it was HDD at first, since this is the only part of the computer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from boo-table USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD appears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoroughly. The problem still persists, what should my next steps be?

  Read the article

< Previous Page | 359 360 361 362 363 364 365 366 367 368 369 370  | Next Page >