Search Results

Search found 18488 results on 740 pages for 'android networking'.

Page 366/740 | < Previous Page | 362 363 364 365 366 367 368 369 370 371 372 373  | Next Page >

• Why would one of my servers stop being able to access other servers by FQDN?

  - by Newlyn Erratt

  I have a number of servers on our local network and our debian server has suddenly stopped being able to access the other servers via their FQDN. Initial symptom was inability to login with Active Directory accounts. On further inspection, this machine, porkbelly, was unable to access our other servers (e.g. bacon and albert) via their FQDN. That is, they can ping albert by running ping albert but not by running ping albert.domain.local though when running ping albert it will be expanded to albert.domain.local. The server is still accessible from other servers via both porkbelly and porkbelly.domain.local. Upon examination of hosts information and running hostname its hostname and FQDN are correct. The resolv.conf appears correct. It contains: domain domain.local search domain.local nameserver 192.168.0.xxx (the nameserver) The dns server is also our Windows AD server. I'm not even sure where to go from here or why dns seems to be partially working though I don't have much experience. Where should I go from here? What might be causing this issue where machines are visible via their hostname but not their FQDN?

  Read the article

• Network card very slow, only on Windows

  - by J Penguin

  This only happens to 1 of my machine, and only when booting into Windows 7. No matter what network card I put in, Windows would default its mode to 10Mbps full duplex. Transfer speed is approximately 1 MB/s. If I set it to 100Mbps, the transfer drops to 100-200K/s. If I set it to 1000Mbps, the connection is lost completely. I've tried swapping in different cards, both PCI-E and PCI. I'v etried update the windows, I've tried reinstalling the drivers... On this very same machine, if I boot into Fedora, it can use the card at its full capacity 1000Mbps transfering 80+ MB/s And all the cards work just fine when plugging into other machines on the same network. I'm very curious. What could be the reason for this? The only different software that this machine has is virtual box with a VPN emulator, but disabling that VPN doesn't seem to do anything. I would like to get this fixed, hopefully, without reinstalling windows _< Will that be possible?

  Read the article

• Windows 2008 R2 Servers Sending Arp Requests for IPs outside Subnet

  - by Kyle Brandt

  By running a packet capture on my my routers I see some of my servers sending ARP requests for IPs that exist outside of its network. For example if my network is: Network: 8.8.8.0/24 Gateway: 8.8.8.1 (MAC: 00:21:9b:aa:aa:aa) Example Server: 8.8.8.20 (MAC: 00:21:9b:bb:bb:bb) By running a capture on the interface that has 8.8.8.1 I see requests like: Sender Mac: 00:21:9b:bb:bb:bb Sender IP: 8.8.8.20 Target MAC: 00:21:9b:aa:aa:aa Target IP: 69.63.181.58 Anyone seen this behavior before? My understanding of ARP is that requests should only go out for IPs within the subnet... Am I confused in my understanding of ARP? If I am not confused, anyone seen this behavior? Also, these seem to happen in bursts and it doesn't happen when I do something like ping an IP outside of the network. Update: In response to Ian's questions. I am not running anything like Hyper-V. I have multiple interfaces but only one is active (Using BACS failover teaming). The subnet mask is 255.255.255.0 (Even if it were something different it wouldn't explain an IP like 69.63.181.58). When I run MS Network Monitor or wireshark I do not see these ARP requests. What happens is that on the router capturing I see a burst of about 10 requests for IPs outside of the network from the host machine. On the machine itself using wireshark or NetMon I see a flood of ARP responses for all the machines on the network. However, I don't see any requests in the capture asking for those responses. So it seems like maybe it is maybe refreshing the arp cache but including IPs that outside of the network. Also when it does this NetMon doesn't show the ARP requests?

  Read the article

• Wireless to Wireless Transfer Slow on a Linksys WRT54GL

  - by Kyle Brandt

  The Situation: When I try to transfer a file from one computer to another that are both connected via wireless on a WRT54GL (in a office) with dd-wrt firmware I often get bad speeds. In generally they average around 100 kilobytes a second. Either computer can download via wireless from the Internet at at about 2 megabytes a second. The speed is slow with the transfer of one large file. There are about 20 other wireless networks that the computers can see, so there is a lot of noise, but I don't have the equipment to really monitor the frequencies well. But that still seems pretty slow. I thought maybe it was the transmit on each card, but even when they are 5 feet away with a line of sight I still get these speeds. According to Linux both cards are operating at 54g. My Questions: Is this normal for this sort of consumer level wireless equipment? Anything I can do to improve it? why is wireless to wireless transfer slow when everything else isn't? Whats steps might I take to figure out what is happening? For example, are lots of packets not making to the access point requiring retransmissions? Above all, I want to find out what the problem actually is. This may seem odd, but at this point I am more interested in understanding what the problem is than fixing it. What I have tried: I have tried messing with lots of settings. Different channels, xmit power, G-Only, none of which has made anything any better. I've also tried upgrading to newer dd-wrt firmware version and doing a reset to wipe out the settings.

  Read the article

• Vlans and subinterfaces

  - by Adeodatus

  I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

  Read the article

• debian gateway using iptables

  - by meijuh

  I am having problems setting up a debian gateway server. My goal: Having eth1 the WAN interface. Having eth0 the LAN interface. Allow both ports 22 (SSH) and 80 (HTTP) accessed from the outside world on the gateway (SSH and HTTP run on this server). What I did was the following: Create a file /etc/iptables.rules with contents: /etc/iptables.rules: *nat -A POSTROUTING -o eth1 -j MASQUERADE COMMIT *filter -A INPUT -i lo -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -i eth1 -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -i eth1 -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -i eth1 -j DROP COMMIT edit /etc/network/interfaces as follows: /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.rules auto eth0 allow-hotplug eth0 iface eth0 inet dhcp #auto eth1 #allow-hotplug eth1 #iface eth1 inet dhcp allow-hotplug eth1 iface eth1 inet static address 217.119.224.51 netmask 255.255.255.248 gateway 217.119.224.49 dns-nameservers 217.119.226.67 217.119.226.68 Uncomment the rule net.ipv4.ip_forward=1 in /etc/sysctl.conf to allow packet forwarding. The static settings for eth1 such as the ip address I got from my router (which I want to replace); I simply copied these. I have a (windows) DNS + DHCP server on ip address 10.180.1.10, which assigns ip address 10.180.1.44 to eth0. What this server does is not really interesting it only maps domain names on our local network and assigns one static ip to the gateway. What works: on the gateway itself I can ping 8.8.8.8 and google.nl. So that is okey. What does not work: (1) Every machine connected to eth0 (indirectly via a switch) can not ping an ip or a domain. So I guess the gateway can not be found. (2) Also when I configure my linux machine (a laptop) to use a static ip 10.180.1.41, a mask and a gateway (10.180.1.44) I can not ping an ip or domain either. This means that maybe my iptables is incorrect of not loaded correctly. Or I maybe have to configure my DNS/DHCP on my windows machine. I have not reset the windows machine net, restart the DNS/DHCP services, should I do this? I did not install dnsmasq as desribed here: http://blog.noviantech.com/2010/12/22/debian-router-gateway-in-15-minutes/. I don't think this is necessary?

  Read the article

• Block Skype on Cisco IOS

  - by ensnare

  I'm trying to block skype via policy routing but it's not working ... here's my configuration: class-map match-any block match protocol skype policy-map QoS-Priority-Input class block police 1000000 31250 31250 conform-action drop exceed-action drop violate-action drop policy-map QoS-Priority-Output class block police 1000000 31250 31250 conform-action drop exceed-action drop violate-action drop interface FastEthernet4 description WAN service-policy input QoS-Priority-Input service-policy output QoS-Priority-Output

  Read the article

• Troubleshooting Website problems within the local network

  - by HaydnWVN

  Have an external website which opens fine on some PC's, yet seems to time out (or symptoms of timing out, but never actually does) on others. Seems to only affect (some) of our newer HP Pro 3305 MT Workstations. All of which are running Win7 32bit SP1 with all updates. Older PC's (Win7 32bit SP1 & WinXP) are unaffected. Using Google Chrome & Firefox makes no difference. Opening the website in IE9 Compatibility Mode has exactly the same symptoms. All PC's are on the same local network (Workgroup) using the same DNS server & gateway (inhouse) on the same internet connection, on the same subnet. There is no proxy server, no content filtering, no load balancing etc etc. Only group policy in effect (locally) is for Update scheduling. Local firewalls are all the same (Kaspersky WP4) and our external facing firewall has no IP specific settings. I have no control over the external website, traceroute shows the same destination on all PC's. It is a fairly popular website in our industry (Horticulture) and i'm not aware of any other people (even other sites within our sister companies) with the same problem. Update: Used Fiddler2 to monitor the HTTP request, seems its not getting fulfilled for some reason?! Request sent: GET http://www.rhs.org.uk/ HTTP/1.1 Host: www.rhs.org.uk Connection: keep-alive User-Agent: Mozilla/5.0 (Windows NT 6.1) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-GB,en-US;q=0.8,en;q=0.6 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Log from Fiddler 2 of the request: This session is not yet complete. Press F5 to refresh when session is complete for updated statistics. Request Count: 1 Bytes Sent: 567 (headers:567; body:0) Bytes Received: 0 (headers:0; body:0) ACTUAL PERFORMANCE -------------- ClientConnected: 17:02:33.720 ClientBeginRequest: 17:02:39.118 GotRequestHeaders: 17:02:39.118 ClientDoneRequest: 17:02:39.118 Determine Gateway: 0ms DNS Lookup: 0ms TCP/IP Connect: 46ms HTTPS Handshake: 0ms ServerConnected: 17:02:39.165 FiddlerBeginRequest: 17:02:39.165 ServerGotRequest: 17:02:39.165 ServerBeginResponse: 00:00:00.000 GotResponseHeaders: 00:00:00.000 ServerDoneResponse: 00:00:00.000 ClientBeginResponse: 00:00:00.000 ClientDoneResponse: 00:00:00.000 RESPONSE BYTES (by Content-Type) -------------- ~headers~: 0 Log of a successful request from a working PC (done this morning, excuse the timestamps being different from above): Request Count: 1 Bytes Sent: 493 (headers:493; body:0) Bytes Received: 20,413 (headers:525; body:19,888) ACTUAL PERFORMANCE -------------- ClientConnected: 08:22:47.766 ClientBeginRequest: 08:22:47.766 GotRequestHeaders: 08:22:47.766 ClientDoneRequest: 08:22:47.766 Determine Gateway: 0ms DNS Lookup: 26ms TCP/IP Connect: 30ms HTTPS Handshake: 0ms ServerConnected: 08:22:47.828 FiddlerBeginRequest: 08:22:47.828 ServerGotRequest: 08:22:47.828 ServerBeginResponse: 08:22:48.905 GotResponseHeaders: 08:22:48.905 ServerDoneResponse: 08:22:48.905 ClientBeginResponse: 08:22:48.905 ClientDoneResponse: 08:22:48.905 Overall Elapsed: 00:00:01.1388020 RESPONSE BYTES (by Content-Type) -------------- text/html: 19,888 ~headers~: 525 So my question has evolved into: What is the difference between the 2 requests and how do I determine why 1 PC is not getting a reply to it's GET request?

  Read the article

• Router block some sites

  - by Mahesha999

  Hi I was using ADSL Modem/Router earlier. The device is quite old Pronet PN-ADSL 101 E/U model (pics: http://bit.ly/P2YaWy, http://bit.ly/OA700l) Since it had only one RJ45 out, I bought new Wireless Router TPLink TL-WR941ND. It has 4 RJ45 out and 3 wireless antennas. I configured my old router in bridge. Now, if I have to connect my pc to Internet through the old router, I have to enter username and password. Then I connected the RJ45 output of old router to the WAN in of new router. and ran the CD of new router. It configured the new router in PPPoE by saving the username and password in router to dial automatically. So now I have to just plug in the wires in my new routers any RJ45 out. I am able to access the Internet when I connect through new router (both wired and wirelessly), but some sites are getting blocked. Most notably yahoo.com (though ymail.com is working), Microsoft.com. msn.com. These sites work perfectly fine when I connect my pc directly to my old router and enter username and password manually. (However others like google.com. facebook.com works fine when connect through new router) So here these some sites need some parameter set but I am unable to find them out. Can anyone help me. My friend said he also faced same problem. Surprisingly he advised me to see if the same websites will work through Opera turbo mode and boom they worked. So what could be the problem?

  Read the article

• Network use of Gaming PC

  - by Matthew Patrick Cashatt

  Background After YEARS of waiting, I built the custom gaming PC of my dreams: Intel i7 - 975 Extreme Edition 3.3ghz (overclocked to 4.0) ATI Radeon 5970 2gb Corsair 256 gb SSD Drive 2 TB Sata II 3.0 7200rpm data drive 12 GB Kingston Hyper-X (1600mhz) DDR3 Windows 7 Ultra 64 bit And so on. . . Problem I hooked this beast up to our home theater and settled in for a great gaming season only to realize a couple of drawbacks: It's hard to accurately wax bad guys using a keyboard in your lap whilst reclined on your couch (and using a wireless keyboard). It's hard to read the text on the screen (i.e. menus, etc). I find that a 1:1 ratio (screen diagonal inch to inch away from screen) is optimum, but using the home theater, it's more like 1:3 which has me squinting unless I sit on the coffee table. The wife always seems to want the TV the same time I do and, unfortunately "Real Housewives of Beverly Hills" and Battlefield BC don't mix. I am losing the battle in the home theater room, but the PC has to stay there (long story). So, this leaves me with the option of playing in my home office which is about 30 feet away from the home theater. I am a software developer so I have a pretty decent set up in my office--multiple 1080p monitors, HP Envy 17 which can run games like Crysis in 720p with out stammering too much. Also, I can game very comfortably at my desk in the office. Still, even though the set up in my office can run games well enough, I don't want to regress to that when I have worked YEARS for an awesome gaming PC that can run everything on ultra high settings. My Question What are my options for running my games on the beastly desktop in the Home Theater, but physically playing in my office about 30 feet away? A really long HDMI cable? LAN/RDC? Details that May Help We have an open crawlspace so running cable from HT room to office is no problem. I already have networked the house with a LAN Any help is GREATLY appreciated. Thanks, Matt

  Read the article

• OpenVPN on Tomato and Vista - can't see my network

  - by Ian

  I followed the instructions here (http://todayguesswhat.blogspot.ca/2011/03/quick-simple-vpn-setup-guide-using.html) to set up a TCP connection to OpenVPN on my Tomato router. Used TCP because the place I usually surf at seems to have the other ports blocked. My Vista laptop is able to connect to the router but I don't appear to be getting an IP address. I'm able to access my router's admin page, but I can't see the network at home. When I browse to Whatsmyip I see my home IP. Here are the results of route print -4 when I'm just connect to the library and when I've fired up the VP connection as well: Library only: =========================================================================== Interface List 22 ...00 ff c4 a0 e7 5c ...... TAP-Win32 Adapter V9 15 ...00 23 4e 20 b3 64 ...... Atheros AR9281 Wireless Network Adapter 10 ...00 23 8b 39 ec 71 ...... Marvell Yukon 88E8040T PCI-E Fast Ethernet Controller 1 ........................... Software Loopback Interface 1 11 ...00 00 00 00 00 00 00 e0 isatap.{834A8A0A-5E2C-47D0-9673-7965DE8B5470} 14 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 17 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 20 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 18 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 19 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 23 ...00 00 00 00 00 00 00 e0 isatap.{C4A0E75C-765E-4F7D-A55C-77945779816A} 34 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #5 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Library and TCP OpenVPN: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.116 30 0.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 24.212.205.68 255.255.255.255 10.1.29.1 10.1.29.117 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 192.168.1.0 255.255.255.0 On-link 192.168.1.116 286 192.168.1.116 255.255.255.255 On-link 192.168.1.116 286 192.168.1.255 255.255.255.255 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.116 286 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Thanks for any advice. I looked at one of the answers but I'm not sure if it applied to me as it said that 10...* was the vpn connection, but I appear to have 10...* when I connect just to the library.

  Read the article

• Monitoring/logging a malfunctioning internet connection

  - by Pekka

  I have a mysterious internet connection problem: Every 15-20 minutes, the connection will become very slow, and take 2-3 minutes for anything to load. I've had a technician from the ISP over here to test the hardware, and everything is in pristine condition. They have no other explanation than a configuration error on my machine, a possibility I can exclude 90% because I'm experiencing the same problems with another machine. I will have to monitor the situation now, and I would like to run a program that logs when internet connections become slow. I thought about putting something together using at and wget. Does anybody know of some other tool for this that does this out of the box - maybe something with an adjustable request frequency, logging connection speeds etc.?

  Read the article

• How to access Parallels guest network services in a shared network virtual machine running in Mac OS

  - by Daniel Silveira

  I have a Windows virtual machine running inside Parallels in my Mac OSX. This virtual machine is setup to use shared network. What I want is: How to access a IIS service running inside this virtual machine from other computers in the network?

  Read the article

• My DNS cannot resolve an web site address?

  - by ipkiss

  Hello all, Recently, I could not access the webpage bbc.co.uk anymore, while I can access other websites smoothly. Ar first, I though there may be some problem with my laptop. However, if I use my laptop through my company network, I can load the page bbc.co.uk normally. Then, I though maybe my ADSL at home blocks that web address. However, I tried another laptop with my home ADSL and it can load the page bbc.co.uk very fast. Now I do not know what could be the problem. Can anyone tell me please? Thank you.

  Read the article

• mail server administration

  - by kibs

  MY postfix does not show that it is listening to the smtp daemon getting mesaage below: The message WAS NOT relayed Reporting-MTA: dns; mail.mak.ac.ug Received-From-MTA: smtp; mail.mak.ac.ug ([127.0.0.1]) Arrival-Date: Wed, 19 May 2010 12:45:20 +0300 (EAT) Original-Recipient: rfc822;[email protected] Final-Recipient: rfc822;[email protected] Action: failed Status: 5.4.0 Remote-MTA: dns; 127.0.0.1 Diagnostic-Code: smtp; 554 5.4.0 Error: too many hops Last-Attempt-Date: Wed, 19 May 2010 12:45:20 +0300 (EAT) Final-Log-ID: 23434-08/A38QHg8z+0r7 undeliverable mail MTA BLOCKED OUTPUT FROM lsof -i tcp:25 command master 3014 root 12u IPv4 9429 TCP *:smtp (LISTEN) (Postfix as a user is missing )

  Read the article

• CentOS: eth0 not starting on boot

  - by Cameron Aziz

  Whenever I reboot a CentOS Hyper-V VM, eth0 does not start automatically. All I need to do is perform ifup eth0 and all is fixed, but that isn't feasible from ssh! I am starting in runlevel 3. After I perform ifup eth0 on the console: [root@localhost ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:15:5D:2B:2B:07 inet addr:10.10.0.3 Bcast:10.10.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe2b:2b07/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:49 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4656 (4.5 KiB) TX bytes:6399 (6.2 KiB) Interrupt:9 Base address:0xa000 [root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none IPADDR=10.10.0.3 NETMASK=255.255.255.0 GATEWAY=10.10.0.1 USERCTL=no ONBOOT=yes [root@localhost ~]# chkconfig --list | grep network network 0:off 1:off 2:on 3:on 4:on 5:on 6:off

  Read the article

• Ubuntu Wireless card not found

  - by user32121

  Hello all, I'm trying to setup Ubuntu on an old PC. I ran the following command, lspci, in order to get info on the wireless card installed. 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Does anyone know where I can get drivers for this card/chip? And also, how to install (I'm rather new to linux). Also, I'm sure the card is working because I just formatted over xp, and everything was working well. Thanks in advanced!

  Read the article

• Long connection times from PHP to MySQL on EC2

  - by Erik Giberti

  I'm having an intermittent issue connecting to a database slave with InnoDB. Intermittently I get connections taking longer than 2 seconds. These servers are hosted on Amazon's EC2. The app server is PHP 5.2/Apache running on Ubuntu. The DB slave is running Percona's XtraDB 5.1 on Ubuntu 9.10. It's using an EBS Raid array for the data storage. We already use skip name resolve and bind to address 0.0.0.0. This is a stub of the PHP code that's failing $tmp = mysqli_init(); $start_time = microtime(true); $tmp-options(MYSQLI_OPT_CONNECT_TIMEOUT, 2); $tmp-real_connect($DB_SERVERS[$server]['server'], $DB_SERVERS[$server]['username'], $DB_SERVERS[$server]['password'], $DB_SERVERS[$server]['schema'], $DB_SERVERS[$server]['port']); if(mysqli_connect_errno()){ $timer = microtime(true) - $start_time; mail($errors_to,'DB connection error',$timer); } There's more than 300Mb available on the DB server for new connections and the server is nowhere near the max allowed (60 of 1,200). Loading on both servers is < 2 on 4 core m1.xlarge instances. Some highlights from the mysql config max_connections = 1200 thread_stack = 512K thread_cache_size = 1024 thread_concurrency = 16 innodb-file-per-table innodb_additional_mem_pool_size = 16M innodb_buffer_pool_size = 13G Any help on tracing the source of the slowdown is appreciated. [EDIT] I have been updating the sysctl values for the network but they don't seem to be fixing the problem. I made the following adjustments on both the database and application servers. net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_sack = 0 net.ipv4.tcp_timestamps = 0 net.ipv4.tcp_fin_timeout = 20 net.ipv4.tcp_keepalive_time = 180 net.ipv4.tcp_max_syn_backlog = 1280 net.ipv4.tcp_synack_retries = 1 net.core.rmem_max = 16777216 net.core.wmem_max = 16777216 net.ipv4.tcp_rmem = 4096 87380 16777216 net.ipv4.tcp_wmem = 4096 87380 16777216 [EDIT] Per jaimieb's suggestion, I added some tracing and captured the following data using time. This server handles about 51 queries/second at this the time of day. The connection error was raised once (at 13:06:36) during the 3 minute window outlined below. Since there was 1 failure and roughly 9,200 successful connections, I think this isn't going to produce anything meaningful in terms of reporting. Script: date /root/database_server.txt (time mysql -h database_Server -D schema_name -u appuser -p apppassword -e '') /dev/null 2 /root/database_server.txt Results: === Application Server 1 === Mon Feb 22 13:05:01 EST 2010 real 0m0.008s user 0m0.001s sys 0m0.000s Mon Feb 22 13:06:01 EST 2010 real 0m0.007s user 0m0.002s sys 0m0.000s Mon Feb 22 13:07:01 EST 2010 real 0m0.008s user 0m0.000s sys 0m0.001s === Application Server 2 === Mon Feb 22 13:05:01 EST 2010 real 0m0.009s user 0m0.000s sys 0m0.002s Mon Feb 22 13:06:01 EST 2010 real 0m0.009s user 0m0.001s sys 0m0.003s Mon Feb 22 13:07:01 EST 2010 real 0m0.008s user 0m0.000s sys 0m0.001s === Database Server === Mon Feb 22 13:05:01 EST 2010 real 0m0.016s user 0m0.000s sys 0m0.010s Mon Feb 22 13:06:01 EST 2010 real 0m0.006s user 0m0.010s sys 0m0.000s Mon Feb 22 13:07:01 EST 2010 real 0m0.016s user 0m0.000s sys 0m0.010s [EDIT] Per a suggestion received on a LinkedIn question, I tried setting the back_log value higher. We had been running the default value (50) and increased it to 150. We also raised the kernel value /proc/sys/net/core/somaxconn (maximum socket connections) to 256 on both the application and database server from the default 128. We did see some elevation in processor utilization as a result but still received connection timeouts.

  Read the article

• AuthInfoRequired cups overwrites

  - by mooscape

  My problem is basically identical to the following: http://bbs.archlinux.org/viewtopic.php?id=61826 Put simply, I have a machine in ubuntu trying to connect to another ubuntu machine via a network in order to use the printer attached. There is no problem printing until I restart the guest machine. Immediately it overwrites the printers.conf file (under /etc/cups/printers.conf). It always adds the same line: AuthInfoRequired username,password I stop cups and change it to *#*AuthInfoRequired username,password to comment out the command. Start cups. Works great 'til the next shutdown. Then it gets overwritten again. Googling indicates it may be GTK problem and not CUPS, but I have found no permanent solution to date. Any suggestions appreciated ....

  Read the article

• Browser caching is generating hugo I/O to server

  - by Rime

  Our users My Documents are stored on a Emc NAS. I have noticed huge traffic coming from users and I see that most of it is coming to cache directories of Internet Explorer and other browsers. One thing i suspect is Adobe Flash caching streams. We have various Windows clients and no restrictions on browsers. Is there any way to remove this traffic from our NAS by a group policy or whatever? Thanks Rime

  Read the article

• Secure openVPN using IPTABLES

  - by bob franklin smith harriet

  Hey, I setup an openVPN server and it works ok. The next step is to secure it, I opted to use IPTABLES to only allow certain connections through but so far it is not working. I want to enable access to the network behind my openVPN server, and allow other services (web access), when iptables is disabaled or set to allow all this works fine, when using my following rules it does not. also note, I already configured openVPN itself to do what i want and it works fine, its only failing when iptables is started. Any help to tell me why this isnt working will appreciated here. These are the lines that I added in accordance with openVPN's recommendations, unfortunately testing these commands shows that they are requiered, they seem incredibly insecure though, any way to get around using them? # Allow TUN interface connections to OpenVPN server -A INPUT -i tun+ -j ACCEPT #allow TUN interface connections to be forwarded through other interfaces -A FORWARD -i tun+ -j ACCEPT # Allow TAP interface connections to OpenVPN server -A INPUT -i tap+ -j ACCEPT # Allow TAP interface connections to be forwarded through other interfaces -A FORWARD -i tap+ -j ACCEPT These are the new chains and commands i added to restrict access as much as possible unfortunately with these enabled, all that happens is the openVPN connection establishes fine, and then there is no access to the rest of the network behind the openVPN server note I am configuring the main iptables file and I am paranoid so all ports and ip addresses are altered, and -N etc appears before this so ignore that they dont appear. and i added some explanations of what i 'intended' these rules to do, so you dont waste time figuring out where i went wrong : 4 #accepts the vpn over port 1192 -A INPUT -p udp -m udp --dport 1192 -j ACCEPT -A INPUT -j INPUT-FIREWALL -A OUTPUT -j ACCEPT #packets that are to be forwarded from 10.10.1.0 network (all open vpn clients) to the internal network (192.168.5.0) jump to [sic]foward-firewall chain -A FORWARD -s 10.10.1.0/24 -d 192.168.5.0/24 -j FOWARD-FIREWALL #same as above, except for a different internal network -A FORWARD -s 10.10.1.0/24 -d 10.100.5.0/24 -j FOWARD-FIREWALL # reject any not from either of those two ranges -A FORWARD -j REJECT -A INPUT-FIREWALL -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT-FIREWALL -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT-FIREWALL -j REJECT -A FOWARD-FIREWALL -m state --state RELATED,ESTABLISHED -j ACCEPT #80 443 and 53 are accepted -A FOWARD-FIREWALL -m tcp -p tcp --dport 80 -j ACCEPT -A FOWARD-FIREWALL -m tcp -p tcp --dport 443 -j ACCEPT #192.168.5.150 = openVPN sever -A FOWARD-FIREWALL -m tcp -p tcp -d 192.168.5.150 --dport 53 -j ACCEPT -A FOWARD-FIREWALL -m udp -p udp -d 192.168.5.150 --dport 53 -j ACCEPT -A FOWARD-FIREWALL -j REJECT COMMIT now I wait :D

  Read the article

• Internet keeps getting Disconnected & Reconnected

  - by Paul

  I have an Internet connection thru a Phone company which uses DSL modem to connect. For past few weeks my net connection keeps getting disconnected for few seconds & it reconnects automatically. I asked the service provider & they checked & even replaced some wires but of no help. Funny thing is that sometimes there seems to be a rhythm where it disconnects for an average of 13 seconds or so plus or minus few seconds, for hours at a time. I don't know how to attach an image to this post where it shows the pattern of connect & disconnect. I have taken an image using snagit to show the timing pattern. If someone can explain it, I can attach it here. Thanks

  Read the article

• 2 x Netgear GS724T (Dual GBIC) trunking issue

  - by Arthor

  I have the following: Netgear GS724T (Firmware Version V1.0.3_35, Protocol Version - 2.001.002) 4 x Indineon ISFP GBR/FC Settings STP Function - Enabled Fast Link - Enabled Trunking port 23,24, (21,22 - RJ45 cables, but not connected.) I have connected both switches via 2 fiber cables and want to use trunking. The problem I am having. Sometimes I get a an issue when none of the switches cannot talk with each other, nor the devices, sometime they can. The problem is irregular and no patten can be determined The statistics shows that when the switches does not work, they have RX errors If I remove one to the GBIC connections, then everything works as normal.] Question Does anyone have a solution for this please? Thanks

  Read the article

• Is there a way to turn off the sound that plays when my computer reconnects to the wireless network?

  - by Dan Tao

  I know this seems silly. Obviously I could mute my computer, or turn the speakers off. But it seems like surely there should be a way that I can keep all of my normal computer sounds without having to hear this one sound (no, it doesn't really bother me; mostly my wife just wants me to turn it off because she finds it annoying). I tried right-clicking on the volume icon in the notification area and went through all of the sounds in the list, thinking I could find the one offending noise and just turn it off. But none of them seem to correspond to the sound that plays when my wireless adapter randomly disconnects and reconnects to the wireless network.

  Read the article

• How should I set up my Hyper-V server and network topology?

  - by Daniel Waechter

  This is my first time setting up either Hyper-V or Windows 2008, so please bear with me. I am setting up a pretty decent server running Windows Server 2008 R2 to be a remote (colocated) Hyper-V host. It will be hosting Linux and Windows VMs, initially for developers to use but eventually also to do some web hosting and other tasks. Currently I have two VMs, one Windows and one Ubuntu Linux, running pretty well, and I plan to clone them for future use. Right now I'm considering the best ways to configure developer and administrator access to the server once it is moved into the colocation facility, and I'm seeking advice on that. My thought is to set up a VPN for access to certain features of the VMs on the server, but I have a few different options for going about this: Connect the server to an existing hardware firewall (an old-ish Netscreen 5-GT) that can create a VPN and map external IPs to the VMs, which will have their own IPs exposed through the virtual interface. One problem with this choice is that I'm the only one trained on the Netscreen, and its interface is a bit baroque, so others may have difficulty maintaining it. Advantage is that I already know how to do it, and I know it will do what I need. Connect the server directly to the network and configure the Windows 2008 firewall to restrict access to the VMs and set up a VPN. I haven't done this before, so it will have a learning curve, but I'm willing to learn if this option is better long-term than the Netscreen. Another advantage is that I won't have to train anyone on the Netscreen interface. Still, I'm not certain if the capabilities of the Windows software firewall as far as creating VPNs, setting up rules for external access to certain ports on the IPs of Hyper-V servers, etc. Will it be sufficient for my needs and easy enough to set up / maintain? Anything else? What are the limitations of my approaches? What are the best practices / what has worked well for you? Remember that I need to set up developer access as well as consumer access to some services. Is a VPN even the right choice?

  Read the article

< Previous Page | 362 363 364 365 366 367 368 369 370 371 372 373  | Next Page >