Search Results

Search found 73994 results on 2960 pages for 'computer help'.

Page 373/2960 | < Previous Page | 369 370 371 372 373 374 375 376 377 378 379 380  | Next Page >

  • crippling repeating "pciehp card not present" notifications

    - by Nanne
    When using ubuntu (12.04, both installed and on a live usb) I get a lot of these messages: pciehp 0000:00:1c.5:pcie04: Card not present on Slot(37) pciehp 0000:00:1c.5:pcie04: Card present on Slot(37) And with a lot I mean about 20 per second. This has a crippling effect, and I would like to get rid of it :) The computer is a packard bell easynote BG48-U-100 DC. I tip I picked up from some fedora/redhat error here was to look at lspci -vnn. I have pasted the part about "00:1c.5" here: http://pastebin.com/0sfsiqW2 For what good it may do, here is the lsmod of my machine: http://pastebin.com/DQZy1kAL From that first pastebin I think to conclude that it has to do with the module shpchp, which seems to me (aka: google) to have something to do with ACPI. That's as far as I've come in disecting this. Can anyone help me along further? What can I do, check etc? I did see this topic but my intentions are not to surpress the error message: I know how to do this (from that topic ;) ), but I'm looking for a real sollution. Finding the problem on the internet does suspect me to believe it is neither an ubuntu specific nor a packard-bell specific problem.If you google the problem it seems that is present on several other distribution/hardware combo's as well, and it looks like the advice is to remove one of the drivers? I have no clue as to which driver I should look at and and what would be the effect of just removing it. I have seen this topic which is old-ish, but describes my problem and is about a similar computer. The solution in this topic was to compile a new kernel using a spanish guide, which seems a bit extreme to me, so I'm kinda hoping for a better solution than that.

    Read the article

  • Port forwarding not working?

    - by rphello101
    I'm trying to set up an Apache Server to be accessed publicly. I'm using a Netgear R4500 router hooked up to a Motorola SB6121 modem. I can access my server on my computer by typing in my IP address. After following the instructions to forward port 80 so I can access the server from other computers, it does not work (see image). I get "This webpage is not available". I am forwarding to the IP address of my computer. Using this Network Port Scanner Tool, it says "80/tcp filtered http", which, as I understand it, means forwarding did not work correctly. In my Apache httpd file, I have: ServerName 192.168.1.13:80 and Listen 192.168.1.13:80 Anyone know what's wrong or have something I can try? click to enlarge

    Read the article

  • Pros and Cons between learning to program on Windows and Linux and Macs

    - by Amumu
    I have been studying IT for 2 years and I'm going to graduate soon in this year (if everything goes well). I think it's time for me to choose a path to specialized into some fields of this large industry. Personally, I want to be a game programmer. But to be a game programmer, surely I have to invest my time to study Windows Programming, then DirectX and other programming techniques related to game. On the other hand, Linux seems promising as well. I am not sure about Game Programming on for it, but it seems become an expert for this OS, and by expert it's not about using the OS to become an administrator, but can do further than that, such as understand the OS to its essence and can produce applications for it. However, there's some obstacles in my view for this development path. Many of my friends think that Linux is based on free and open source, and if you follow it, as its name suggested: Free and Open Source, it means we also give away our software free. Otherwise, we will have to find a second job to make living. Currently, I think a viable way to make money on Linux is doing works related to client-server. Another way to developer my career is to become expert in developing business applications for companies. This is more on business, not on specialized IT fields so I am not really interested. Another alternative is programming on mobile devices, such as iPhone, Android and it seems very promising and easier to approach. Another way is to become a computer scientist and research on academic subjects such as AI, human-computer interaction, but this is far beyond my reach, so I won't invest my time on it until I feel I am experienced enough. That's all I can think of for now. I may miss a lot of things, so I need more opinions as input to get the big picture of the industry for my career path.

    Read the article

  • How to maximise performance in computers connected into LAN via Gigabit ethernet router?

    - by penyuan
    Our group is setting up a server (which might just be a NAS, but we're not sure yet), which shares files, so that it connects to all other computers in the room (about 10 of them). I am thinking just hooking all of them up via a gigabit router/switch. Is there anything I should watch out for, in terms of cables, connections, or the connection capabilities of each computer in the network? For instance, I don't want a slow computer in the LAN to slow down everyone else's connection, etc., etc. Thanks for the education.

    Read the article

  • Interview questions for programming tutor?

    - by Emmett Gear
    My family is looking for a programming/computer science tutor. Personally, I want to learn Java or some other brand of web programming. I am best described as a PC "power user." I have never programmed in the past and would like a good jump start. I am a very quick learner and do not expect the tutor to have to teach me the ultra basic stuff that I can learn myself. My son also needs a programming tutor. He just got into Carnegie Mellon as a computer science major. Having done only robotics and mathematics in the past he is very nervous that he does not have the same level of knowledge as his future classmates. I need some help coming up with a list of questions to ask potential tutors and some criteria to judge them by. Thanks! Edit: So far I have come up with just the obvious... Where did you receive your education? What languages are you familiar with? How long have you been tutoring? What made you decide to become a tutor? What software projects have you worked on? What work references can you give me? How much do you charge?

    Read the article

  • What do encrypted files' data look like?

    - by Frost Shadow
    I know there are a lot of encryption programs available, that I would guess use different methods for encryption, and thus have different types of output files (.fve .tc .cha .dmg (bitlocker, truecrypt, challenger, ect.)), but if someone didn't know what the file was and just looked at the data, what would it look like? Does it just look like random bits, or can you still pick out a pattern? If it does look random, how is it if I moved the encrypted file to another computer, the other computer can tell it's a file, and is able to decrypt it (how would it even know where to start or stop, if it all looked random)? Also, how is the structure affected by encrypting files twice, using the same method, or a different one? Thanks for any help, and if you know any books or site about encryption for complete idiots, I'd appreciate it!

    Read the article

  • How to debug suspend?

    - by mlissner
    I've been using Ubuntu for about five years now, and I still can't make it suspend when I want to. It's quite irritating that I can program up a storm, hack the machine in numerous other ways, and yet, and yet when I try to make it suspend or debug suspend, I fail miserably. I need help. Where do I begin to find the problem? What do I do to fix it? I'm placing a bounty on this, because I've literally lost hours of my life to this problem, and leaving my computer on ALL the time is terrible. The symptoms: Pressing suspend brings my computer to a state where it has a blinking cursor, the fans are running, it seems that the HD has turned off (I think), and I can't do anything to bring it back from this state (short of a hard reboot). Possibly related: My fans stay on even after a shutdown, and even then, I have to press the power button for five seconds before I can start it up again. I don't know what logs to look at to debug the problem, and I imagine they'd get nuked on reboot anyway. Please, please help. This drives me completely nuts, and I've been living with it for over a year.

    Read the article

  • linux recommendations for older pc

    - by jdamae
    Hi, I'm new to Linux and I am interested in installing the OS on an older computer I have. I want to setup a webserver and install php, perl. My pc is an older HP Pavillion a255c, Intel Pentium 4 with 512ram. I will probably add some more memory later. This pc is more like a sandbox than anything, but would like to get quickly started with the OS. Is there a particular flavor of linux I would need to download based on my older computer? Any recommendations? I was thinking about Ubuntu but not sure what version to go with. Thanks for your help.

    Read the article

  • How to switch to a generic kernel in a headless Ubuntu Server 12.04?

    - by chmike
    I just got a dedicated server with Ubuntu 12.04 installed with a custom compiled kernel. Since I would like to install VirtualBox and this custom kernel doesn't support dynamic module loading (for security) I need to change the kernel. I'm running some Ubuntu servers for years but never palyed with grub and a headless computer. When the command update-grub is run it shows the different kernel it finds. Here is what I see Generating grub.cfg ... Found linux image: /boot/bzImage-3.2.13-xxxx-grs-ipv6-64 Found linux image: /boot/vmlinuz-3.2.0-34-generic Found initrd image: /boot/initrd.img-3.2.0-34-generic No volume groups found done The first one is the active one as seen with uname -r. To me it looks like the second kernel is the one I should use. But I don't know how to configure grub2 to use it. The computer is also configured with a software RAID using mdadm I guess. Never used that before. I don't know if playing with the grub of changing kernel could brake this. What must I do to set the generic kernel as the default one so that I can get VirtualBox running.

    Read the article

  • Evolution sending Email Settings

    - by Jack
    Can receive Comcast mail with evolution but cannot send. The SMTP settings record more digits when clicking the Server Configuration apply key. Sending ([email protected]:tenz222) port587 After clicking apply, receive a "Error while sending message" host lookup failed etc When rechecking,the sever settings are, ([email protected]%253atenz222) Attempted this process many times with same result. Now need to be proactive and ask for help. Will phone for help anywhere, anytime in USA. Thanks

    Read the article

  • Rhythmbox - put a playlist on my iPod

    - by GorillaSandwich
    I have an old iPod nano and currently use iTunes in Windows to management. However, I'm trying to switch to Ubuntu. So far, iPod management is one major holdup. Besides being unable to easily manage podcasts, I also don't see a way to create a playlist and put it on my iPod. I can create a playlist on the computer in Rhythmbox, but I can't drag and drop it onto the iPod. I can create a playlist on the iPod itself, put I can't drag and drop songs from my library into it. If I right-click the songs, I can add them to playlists on the computer, but not on the iPod. How can I create a playlist of music in Rhythmbox and sync it to my iPod?

    Read the article

  • Failure to Boot Windows 7 after Ubuntu install

    - by Mike
    My computer is a (brand new) PC notebook, without a CD drive running Windows 7. I followed this page to install from USB: https://help.ubuntu.com/community/Installation/FromUSBStickQuick The installation went well and i am using Ubuntu now (v. 12.04 i believe) I want to be able to dual boot Ubuntu and Win7 The problem is that the disc partitioning during the Linux install caused a problem with Windows, caused some problem with windows, and windows can no longer boot when i choose it at the GNU GRUB screen. When i restart my computer i can successfully boot Linux, but not Windows 7. At the GRUB screen - if i run Win7 normally, it freezes, shows a blue screen, and returns back to GRUB - if i run Win7 recovery, i dont know how to access the files that i need in order to run windows again, so nothing helpful happens. Can you please tell me what i would need to do(or link a guide) in order to run Windows again. (Windows and Linux is preferable, but if thats impossible going back to only Windows will help too) Im guessing the easiest thing to do is just to reinstall both OS, or is there anyway to undo the partition i made during the install? Thanks

    Read the article

  • How to configure DD-WRT routing table when creating an isolated network segment for PCI C VT compliance

    - by tetranz
    I'm the volunteer support and system admin person at a small private school. We need to setup a PCI compliant Windows PC as a virtual terminal for credit card processing. I've read questionnaire SAQ C-VT and, to quote, this computer needs to be accessed: "via a computer that is isolated in a single location, and is not connected to other locations or systems within your environment (this can be achieved via a firewall or network segmentation to isolate the computer from other systems)" Our setup is as follows: DSL modem from ISP is setup to be a "transparent pipe" with no extra services. That goes into the WAN port of Linksys WRT54-GL running a DD-WRT. The LAN is 192.168.1.x. There are a couple of other WRT54-GL / DD-WRT devices. One is used as a wireless AP and another is a client bridge. To isolate the VT (virtual terminal) machine, I have another DD-WRT device. Its WAN is connected to a port on the 192.168.1.x LAN. The virtual terminal machine is connected to its LAN which is at 192.168.10.x. The SPI Firewall etc is turned on. It's basically the default DD-WRT gateway setup where the "ISP" is our own LAN. That's working. All incoming traffic to the VT machine is blocked, including from our own LAN. The VT can access the internet BUT, and here's the problem, it can also ping any of the computers on the 192.168.1.x LAN. I think I need to stop that. I'm guessing that I could do something with the Static Routing table in the VT machine's DD-WRT device. I need to route anything going to 192.168.1.x other than the gateway which is 192.168.1.1 to 0.0.0.0 or something like that. That's where I'm stuck at the end of my knowledge. Or ... do I need to get yet another DD-WRT so the network is "balanced". Maybe I need to have the internet from the DSL going into a DD-WRT which has only two devices on its LAN i.e., two other DD-WRTs, one for the main LAN and one for the VT. I think that would do but I'd like to avoid the extra cost and complexity if I don't need it. Thanks

    Read the article

  • Need to upgrade DDR2 RAM on HP Desktop

    - by jds
    I have this HP Pavilion Desktop. As you can see, that page says the memory speed supported is PC2-4200. It currently has a 512 MB stick - CPU-Z Screenshots: hxxp://i41.tinypic.com/j5clj6.jpg and hxxp://i39.tinypic.com/20tldlc.jpg However, a crucial.com scan gives a slightly different report - hxxp://crucial.com/systemscanner/viewscanbyid.aspx?id=5718CFE831D926C3 It says the system can support PC2-5300 memory. So my question is which one should I trust? I want to upgrade the computer's ram to 2 GB (the maximum supported), because XP Media Center is giving me problems and I will install Windows 7 on this. PC2-6400 is the most common DDR2 memory I have been able to find here in the market. Will it cause any problems if I install 2 × 1 GB PC2-6400 DDR2 memory sticks (in dual channel) in this computer, (afaik, it will just run at the lower speed of 533 MHz, or whatever the motherboard supports), or do I absolutely need to get PC2-4200 sticks?

    Read the article

  • Sharing internet connection from Windows XP using wi-fi router

    - by Darius
    Hi, I have an network configuration like: Ethernet cable from ISP connected to Windows XP machine, configured with static IP 192.168.0.3 Another ethernet connection from 2nd Windows XP machine's network adapter to a Wi-Fi router (D-Link Airport G+) XP set to "Share internet connection", the 2nd adapter configured as static to 192.169.0.1 D-Link Airport Wi-Fi router also configured as "static connection", it's IP set to 192.169.0.2, default gateway set to 192.169.0.1. Network mask everywhere is 24. Laptop computer connected with the router with static IP 192.169.0.3 The problems are: XP machine sees the router (it's able to ping it and access it via the web admin tool) The router somehow cannot PING the XP machine (using the tool provided by the web-based admin tool) The laptop computer cannot ping anything and cannot be pinged The router is only accessible when the ethernet cable is connected with a router's 1-4 LAN port, when I connect it via "WAN" port (which I believe is the proper one) it's not visible from the XP machine If you have similar experience with configuring a network like this I would really appreciate your help. I cannot use the Wi-Fi router with the ISP cable itself.

    Read the article

  • Windows VPN not authenticating from ADSL to Wireless link

    - by deanvz
    I have a normal windows VPN on a computer connecting to a 196.201.x.x/24 IP. If this VPN tries to connect from any address in the 41.x.x.x range it cant get there. The server is a normal windows 2008 server, running exchange with a PPPoE IP natted to a public IP on the public gateway of the wireless network as the server is on site and its connectivity is derived from Mikrotik RB's. The computer on the 41 range can traceroute and ping the server, but the VPN does not authenticate. When on the network or any other, the VPN works fine. Is there something that could be configured on the VPN client? All firewall settings of a standard ADSL router have been checked and found to block only ICMP's. Is this a VPN configuration problem or a network issue?

    Read the article

  • GRUB2 not working after installing xubuntu 14.04

    - by h3bm
    I have a vaio laptop and it used to have installed windows 8 and Xubuntu 13.04 in dual boot, everything was working fine. I decided to update my version of xubuntu 14.04 LTS mainly because the support for 13.04 is finished and LTS version have 3 years of support. What I did was to format the partition where xubuntu 13.04 was installed and install 14.04 in that formated partition. When I restarted my computer willing to start using my new system I got the following message: error: symbol 'grub_term_highlight_color' not found and I was not able to enter any OS. I tried boot-repair from live USB more than two times and it did not fix the problem. I tried to enter to my computer using super GRUB2 disk, however it does not apperar to work with UEFI active (besides super grub2 disk says it can) I only get the message "no operating system found". If I boot super grub2 disk with UEFI disabled, super grub2 disk can not detect any OS,I also tried Rescatux distro, however, as of super grub2 disk, rescatux cannot enter when UEFI is active. I tried boot-repair with the option of "restore EFI backups", after that I was able to boot on windows, but no grub menu appeared. I ran boot-repair again with no improving results Here is the last Bootinfo report I got: http://paste.ubuntu.com/7609801/ Do you have any idea of what is happening? I really appreciate your help, Best regards,

    Read the article

  • Screen is black at login screen if display driver is enabled

    - by Amir Rachum
    I have a Lenovo x200 and recently its screen didn't work, so I took it to a repair lab. The guy told me they replaced the screen inverter. I powered up the laptop and the ThinkPad logo was shown, so I was happy. When I got home the computer would boot up, then instead of the logon screen, I got a black screen. Went to safe mode, disabled the display adapters, reset the computer, and I got a clean boot. Then I tried to reinstall the drivers, and it just led to the same condition. My video card is (from device manager): Mobile Intel(R) 4 Series Express Chipset Family. Now my laptop works as I'm working with display drivers disabled, but without display drivers I can't watch movies, etc. Any solution to this problem? Edit: I plugged in an external monitor and it works on it with display drivers enabled. However, it does not find the laptop monitor.

    Read the article

  • MacBook Refuses to Boot

    - by pas09
    I have a MacBook that has unfortunately died on me. I randomly got a pop up message that said I needed to restart my computer, and once I did, I was greeted with the blinking folder question mark start up screen. I've tried everything, including running Disk Utility repair and reformatting the hard drive and reinstalling OS X. All of my data is backed up and safe, I just need my computer to start again. Before I go off and buy a new hard drive, I wanted to see if there is anything I might have forgotten.

    Read the article

  • Ubuntu 13.04 to 13.10: Filesystem check or mount failed

    - by SamHuckaby
    I attempted to upgrade from Ubuntu 13.04 to 13.10 today, and mid upgrade the system started flaking out, and eventually locked up entirely. I was forced to restart the computer, and am now unable to get the computer to boot up at all. When I boot currently, it takes me to the GRUB menu, and I can choose to boot normally, or boot in an older version. I have tried several things, which I list below, but no matter what, when I try to finish booting into Ubuntu, I receive the following error: Filesystem check or mount failed. A maintenance shell will now be started. CONTROL-D will terminate this shell and continue booting after re-trying filesystems. Any further errors will be ignored root@ubuntu-computername:~# I have fun fsck -f and everything appears correct, no errors are reported. and it passes all 5 checks. If I run fdisk -l then I get the following information: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes Disk identifier: 0x00010824 Device Boot Start End Blocks Id System /dev/sda1 * 2048 608456703 304227328 83 Linux /dev/sda2 608458750 625141759 8341505 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 608458752 625141759 8341504 82 Linux swap / Solaris Disk /dev/sdb: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0fb4b7e8 Device Boot Start End Blocks Id System /dev/sdb1 8192 625139711 312565760 7 HPFS/NTFS/exFAT I am considering just installing a new OS on the other disk, that currently has nothing on it, and then just attempting to scrape my data off the old disk (thankfully I didn't encrypt the files). Really my question is this: Can I salvage this Ubuntu install, or should I give up and just reinstall?

    Read the article

  • One-Way Backup Service? [closed]

    - by Jon Rodriguez
    Up until a month ago, my girlfriend has used MobileMe to backup all the files on her MacBook. This turned out terribly when a quirk of MobileMe caused it to erase all of her files on MobileMe, and then sync the newly-erased MobileMe down to her computer, erasing everything. A week's worth of college essays and CS homework were gone. Now, I am terrified of any commercial cloud-backup solutions because of the possibility of this happening. Going off the list provided in these answers, could you please help me find a good backup service that is completely one-way? I want a service where there is literally not a single line of code that has the possibility of writing to my computer's drive. I want a pure one-way backup service.

    Read the article

  • Apply Group Policy to Remote Desktop Services users but not when they log on to their local system

    - by Kevin Murray
    Running Windows Server 2008 Service Pack 2 with Remote Desktop Services role. I want to hide the servers drives using a GPO, but not the users local drives when they are logged on to their local system. Using a GPO, I went to "User Configuration - Policies - Administrative Template - Windows Components - Windows Explorer" and enabled "Hide these specified drives in My Computer" and "Prevent access to drives from My Computer" and in both used "Restrict all drives". Then under "Security Filtering" for the GPO, I restricted it to the system running Remote Desktop Services and the specific users who will be using RDS. I then applied the GPO to our domain and it worked a little too well. Not only was I successful in getting the GPO to work for RDS users, but it also affected those same users at their local systems as well. I've tried everything I can think of, but can't figure out how to apply this just to the RDS but not at their local system. What am I missing?

    Read the article

  • Windows 7 freezing unexpectedly

    - by Thomas Deutsch
    I have a Windows 7 computer here, which is freezing between 2 times a day and 1 time every second day. I see no problem, no special drivers, no special Apps are open, no encryption or something like that. Apps usually open then are Firefox, Thunderbird, Eclipse and maybe Office. Computer is just freezing. No Reboot, no shutdown, no bluescreen and no error. User has to hardreset it. Eventlog shows me an kernel error saying it has been unexpected rebooted due to an fatal error, but no statement about what kind of error happended. Anyone an idea what it can be? Chkdisk should be ok (currently, I run it a second time).

    Read the article

  • Installing Visual Studio 2010 Service Pack 1

    - by Martin Hinshelwood
    As has become customary when the product team releases a new patch, SP or version I like to document the install. This post seams almost redundant as I had no problems, but I think that is as valuable to other thinking of installing the Service Pack as all the problems that we sometimes get. As per Brian's post I am Installing Visual Studio Team Foundation Server Service Pack 1 first and indeed as this is a single server local deployment I need to install both. If I only install one it will leave the other product broken. Figure: Hopefully this will be more uneventful It takes a little while for your system to be checked to see what components need updating. On my main computer this was pretty quick, but on the laptop it took some time. Figure: There are a lot of components to update With this update also comes an update to .NET as well as many other components. Figure: I downloaded the full 1.5GB’s, but you could do a web install It depends on how good you internet connection is to how long it would take to download, but as I am now in the US I decided not to trust the internet connection speeds. It took around 30-40 minutes to download the full thing which is a little slow. Figure: I did not need to download, but that would increase the install time So on my main computer again this was fast, but again on my netbook this took a little while. Figure: The actual install took around 30-40 minutes (2 hours on netbook) I was pretty impressed with the speed of the install, and as Team Explore is now out of the box with Visual Studio 2010 I don’t get the problem of the SP being installed before Team Explorer and having a disjointed experience Figure: As I suspected, no problems with the install Figure: Checking in Visual Studio shows that all the servicing points were successful This was an easy experience even if the SP was over 1.5GB’s to download Hopefully I will be discovering things that work better for a good while to come, as well as not seeing holes in the product that I had no encountered yet. What were your experiences of installing Visual Studio 2010 Service pack 1?

    Read the article

  • Risk to native OS from Live CD?

    - by Frost Shadow
    Will booting from a Live CD (I was thinking Anonym OS) have any risk to the native OS? I wanted to try it out on my school´s computer, but I´d rather not have to explain why I accidentally reformatted the HD and deleted everything.. I know once you´ve booted the right way, it shouldn´t leave any trace on the HD, but is it possible I can push some wrong button and end up trying to overwrite the native with the Live OS? Also, since the computer itself is connected to the internet, will the network administrator be able to see that i´ve booted from a Live CD? I´m thinking yes, but just thought I´d check. Thanks for any help!

    Read the article

< Previous Page | 369 370 371 372 373 374 375 376 377 378 379 380  | Next Page >