Search Results

Search found 30569 results on 1223 pages for 'computer problems'.

Page 384/1223 | < Previous Page | 380 381 382 383 384 385 386 387 388 389 390 391  | Next Page >

• External SATA drive does not work without the optional USB cable *also* connected

  - by Software Monkey

  I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

  Read the article

• cannot connect to vpn server (error 721)

  - by callmeblessed

  Hi I got 2 internet connections in my computer. One is using 3.5G HSDPA modem (vodafone huawei e220) and the other using mobile phone (cdma zte c261). Both are using different ISP and i have both. at the moment, i can connect to my office vpn using the HSDPA modem one. But when i tried to use cdma modem (dial up - mobile phone modem), i am just able to get "verifying username and password" and then after a few minutes it display error : Error 721 The Remote Computer didn't respond. I tried to ping into my office ip address, it got good result but still cannot connect to the vpn. I tried to turn off all my firewall (i'm using commodo) and has no response as well. In my cdma mobile phone modem Network connections I tried to allow iNternet connection sharing as well ... and turn on all Internet Protocol TCP/IP, File & Printer Sharing & Client for microsoft networks. But all of my effort has no effect. How to fix this problem ? note: my office using windows vpn as well. thank you .

  Read the article

• Changing open-files-limit in mysql 5.5

  - by davidv

  I'm having an issue with mysql 5.5 running on Ubuntu 12.04 with the open-files-limit parameter. I recently noticed some problems due to the 1024 limit, and actually the main system limit was set to 1024, so I modified /etc/security/limits.conf with the following: * soft nofile 32000 * hard nofile 32000 root soft nofile 32000 root hard nofile 32000 After that I check the ulimit value for root and even for mysql user, both returned the new value: 32000, so I assume the change has already been done. I also changed the value at the my.cnf file, setting open-files-limit to 24000, like this: open-files-limit = 24000 Now comes the odd part, when I restart the mysql service and check the open_files_limit variable, it returns that it's still set to 1024, so I'm having the same problems that before (obviously), I tried to use open-files-limit instead open_files_limit in the my.cnf config file, same result, BUT if I override the service command to start the service and start only using mysqld (no additional parameters), the service starts and when I check the parameter it returns 32000... I don't know where it's taking that value from, as it's not set at my.cnf and it's not being given through command line, at least, not for myself. Any ideas about why it's not working the change and how to solve it the normal way (launching it through service...)?

  Read the article

• Installed Paragon HFS+ for Windows 8, now my pc won't recognize the external firewire drive

  - by Steve

  I'm not incredibly knowledgeable about computers and I really need some help. Just got a Seagate external firewire drive this morning. I downloaded the necessary pc driver (Paragon HFS+ for Windows 8) through their website per the instructions that came with the drive. After installation, I restarted and the pc recognized the firewire drive just fine. About three hours into copying files from my pc to the firewire drive, it gave me an error and told me the files couldn't be copied. When I clicked to get out of the message, the computer crashed. After an hour of it trying to repair itself in safe mode, it restored me to an earlier version before the system crashed. Here's my current dilemma: The Paragon HFS+ is still showing up in my programs as installed, but the Device Manager is not recognizing the drive. When I try to uninstall and reinstall Paragon, it interrupts me with a message saying "The setup must update files or services that cannot be updated while the system is running" and basically gives me the finger. I have no idea what to do now, as it won't let me uninstall and reinstall Paragon, and I have no idea why it crashed my computer in the first place. Is there possibly another Mac - PC firewire driver I can try downloading instead? I really don't know what I'm doing and any help would be greatly appreciated.

  Read the article

• Transfering Files to server IP and port

  - by Mason

  I need to transfer files from my local computer on windows 7 to a server running linux. I access the server with putty through ssh at a specific IPv4 address and port number. I've attempted using the pscp command from my local computer but was denied access by the server. "Fatal: Network error: Connection refused" c:>pscp test.csv userid@**IPv4_Addres***:Port# /path/destination_file_name. Either the server blocks all pscp attempts from unauthorized users (most likely my laptop included) or I used the command incorrectly. If you have experience using this command, where exactly will the file get transfered to, I'm assuming that the path destination starts at my home directory in the server. Also if you have any other alternative methods of transfering the files let me know. Update 1 I have also tried using WinSCP however I got permission denied for that as well, it looks like the server will not let me upload or save files. Solved I had a complete lapse of memory and forgot about sudo (spent too much time with scripts the last 2 months), so I was able to change the permissions to allow external editing. Thanks for all the help guys!

  Read the article

• Is there a way to force the monitor to power off in Windows 8?

  - by Rune Jacobsen

  I have googled this a bit and looked at powrprof.dll and PsShutdown but I haven't found a way to do exactly what I want to do. You know that power save option that lets Windows turn off your monitor(s) if you haven't touched the system for x amount of time? Well, I have a PC that needs to be on most of the day (and night), and I have to watch it much of the time, so I can't have a short timeout for automatically turning off the monitor. However, once I leave it for a few hours (happens at varying times of the day), I would like to be able to issue a command that puts the computer in this mode. Not sleep mode, not hibernate mode. Monitor off, that is all. I realize of course I could just turn the physical monitor off. That is not what I want. This Dell monitor takes forever to display a picture from a cold state. If it is turned off by the computer not sending a signal - not so bad. Is there any way for me to do this? As mentioned, the OS can do it, so I would find it really useful if I could do it too. :)

  Read the article

• I get "An error occurred while Windows was synchronizing with [name of time server]." when trying t

  - by ChrisF

  Prompted by the answers to this question I decided to give the Windows built in time synchronisation another go. However, no matter what time server I use I get this error: "An error occurred while Windows was synchronizing with [name of time server]." The help suggests the following as reasons for failure: You are not connected to the Internet. Establish an Internet connection before you attempt to synchronize your clock. Your personal or network firewall prevents clock synchronization. Most corporate and organizational firewalls will block time synchronization, as do some personal firewalls. Home users should read the firewall documentation for information about unblocking network time protocol (NTP). You should be able to synchronize your clock if you switch to Windows Firewall. The Internet time server is too busy or is temporarily unavailable. If this is the case, try synchronizing your clock later, or update it manually by double-clicking the clock on the taskbar. You can also try using a different time server. The time shown on your computer is too different from the current time on the Internet time server. Internet time servers might not synchronize your clock if your computer's time is off by more than 15 hours. To synchronize the time properly, ensure that the date and time settings are set close to your current time in the Date and Time Properties in Control Panel. Now the first reason is clearly wrong - I am connected to the internet. I can see the 2nd being the most likely cause. I have Sygate Personal Firewall running, but it normally asks if something it trying to connect for the first time. Does anyone know I can unblock the NTP protocol - or at least check if it is blocked?. I don't think it's #3 or #4 as I've tried a number of different servers including the one currently used by Atomic Clock Sync. Though if someone knows the address of a UK time server I can double check this.

  Read the article

• Dropped WD External Harddisk, now it's shown as "Not initialized"

  - by Phelios

  So, the WD my passport external harddisk is dropped, and after that, the computer is unable to read it anymore. I was hopping if I can just find another case to try if the harddisk is still readable, but looks like the hard drive itself is not a normal SATA or PATA drive. I think it's modified. So, I can't find another case that I can try on. In the computer, I still can see the drive in the "Disk Management", but it's shown as Uninitialized, no size, and no drive letter. I've also tried a couple of recovery tools. Some can't detect at all, there is one (find and mount software) that can detect but shows 0 size. None of them can recover the data. WD is willing to replace it with a new one, but I still need to recover the data. Any way I can recover the data? UPDATE: I tried initialized it from the windows Disk Manager, but it give error "The request could not be performed because of an I/O device error."

  Read the article

• Printing from Firefox on different printers and setting the page details beforehand

  - by user1162541

  I´ve got an odd problem and I have not been able to fix this. I have a computer which is connected to two printers. One is a receipt printer (EPSON TM-U220), and the other one is an impact printer (Epson LX-300+). From Firefox, I need to print on both printers at different moments. So first I print on the receipt printer, then on the impact printer, etc. However, whenever I first print on the receipt printer, and then go back to the impact printer, the printout is only the width of the page of the receipt printer. That is, the page does not come out properly, just the left part of the page is used for printing and the right part is completely empty, as if I am just printing on the small receipt paper. And there is no way I can tell Firefox that I am printing on this larger printer. The second print on the impact printer goes fine. Firefox now knows it is printing on the impact printer, and it comes out properly on the full page width. But every first print on the impact printer is using the wrong paper size. How can I fix this? When I go to PAGE PREVIEW I can not set the printer UNTIL I actually print the page. If I go to PRINT PREVIEW CONFIGURE PAGE, I can not set the printer I will be using. I can only do so if I go to PRINT PREVIEW PRINT (here is the dropdown box to set the printer). But I can only set the printer and then click PRINT, or CANCEL. If I click PRINT, then the computer remembers the setting but that page will come our wrong, and when I click cancel it simply does not remember the printer I just set.

  Read the article

• How do I fix error 1303 during TI Connect install?

  - by smoth190

  I recently purchased a TI-84 Plus graphing calculator, and I'm trying install the TI Connect software in order to connect the calculator to my computer via the USB cable. Unfortunately, I'm getting this error while trying to install the program: Error 1303. The installation has insufficient privileges to access this directory: E:\Data\Timothy\Documents\MyTIData. The installation cannot continue. Log on as administrator or contact your system administrator. However, my account is the only account on my PC, and it has administrative privileges. I've also tried running the installer with Run as Administrator, but with no luck. If I create the folder MyTIData manually, I receive this error: Error 1317. An error occurred while attempting to create the directory: E:\Data\Timothy\Documents\MyTIData I've reapplied the security settings to the E:\Data folder (and all its sub-directories) to Full for my account. I've also gone into Computer Management, and given SYSTEM full privileges for the entire disk. I've also logged out, logged back in, restarted, etc. but still, no luck. Now, I should mention that my Documents folder is not at the default location. I changed it due to my C: disk being a 90GB SSD, so I moved all my personal data onto the extra storage disk (which is ~1TB). I don't know if that is causing the issue, but it can't hurt throwing it out there. So why can't I install this program? Google'ing the problem brings up this error for various other installers (such as Visual Studio and Microsoft Office), but nothing for TI Connect. All the solutions are the same: Give the folder Full privileges...but I've already done this! I've also tried running the installer with and without the calculator plugged in, but it didn't change anything. In the prompt that contains the error, repeatedly clicking Retry or waiting a few moments before clicking Retry also produces no result.

  Read the article

• Why does my PC successfully boot only when unplugged for more than a few minutes?

  - by philg

  I have an HP Pavilion Elite desktop computer, model HPE-490t. I like it because it didn’t cost too much, boots itself from an SSD, came with 16 GB of RAM, and has 6 CPU cores for editing video and camera RAW images. It has one behavioral quirk that I cannot explain, however. The recent power interruptions here in the Northeast got the machine into a state where it could not be restarted. It would power up for a second or two, shut down, and then power up again, never being able to get to the point of showing anything on the monitor. I unplugged it for about 10 seconds and plugged it back in. Same behavior (fails to boot). I unplugged it and walked away for an hour, then plugged it back in and it worked perfectly! I think something similar happened after installing a second hard disk drive into this machine. So the question is why does the computer behave differently depending on how long it has been unplugged? Where is energy stored that affects the machine’s ability to boot? Capacitors in the power supply? Battery on the motherboard (there is one for the clock, but that wouldn’t be exhausted by being unplugged for an hour, I don’t think)?

  Read the article

• Why can't I mount an image hosted on a read-only HFS+ partition via Boot Camp?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Boot Camp driver package includes file system drivers that enable Windows to access the Mac OS HFS+ partition. It's read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• UDP blocked by Windows XP Firewall when sending to local machine

  - by user36367

  Hi there, I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: - Windows XP Professional with Service Pack 3, all updated - Program that sends UDP datagrams - Program that receives UDP datagrams - Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas? Thanks in advance!

  Read the article

• How can I get Windows 8 to automatically disable touch when I am using my Wacom pen and turn it back on when I am not

  - by Robert

  I have an HP convertible tablet computer which I just upgraded to Windows 8. The problem (which existed under Windows 7 as well) is that this tablet has both a capacitive touch screen (with multi-touch) AND a wacom-type tablet built in to the screen that works using electro-magnetic resonance with the provided stylus. My Use Case: Most of the time I am happy using my fingers and the touch interface for navigation and whatnot. However, when I want to get down to serious note-taking/drawing, I want to use the wacom functionality. The problem is that any comfortable writing position has me resting my arm/hand on the screen, which activates the touch technology (despite supposed palm-detection algorithms) and completely screws up my input paradigm. My Ideal Solution: Ideallly, since wacom technology senses when the pen is "close" to the screen, I would love to have touch be automatically disabled whenever the wacom pen is detected, and turned back on when it is out of range. this would allow me to seamless switch between the two input methods, and since I NEVER want to use both at once would work perfectly for me. An acceptable alternative: As a next best option, It would be great to be able to turn off the touch functionality (leaving the wacom in place) whenever I entered specific apps (e.g. OneNote, Photoshop, Gimp, Pencil, etc.) and then have it turn back on when I left that app.... As a worst case at least lets me use my PC option: If I could create a shortcut (tile or otherwise) that flips the touch on and off without going all the way through the nested computer settings, that would be better than nothing. Thanks in advance for the help with 1 or more of the above.

  Read the article

• Synchronize folders on different computers without cloud and without network just internet

  - by theimmortalbg

  I have two computers with windows 7, one in my home town and one in another town. So they are not in private network but I have internet on both. They have exactly the same file structure. I am searching for program that can keep the data equal. I know about dropbox or google drive but they are cloud and I don't want to use them. Also they are using folder that you should copy your data in it. There is another programs that are like a server, just put something and after that you can download it but I dont need them. I want just to point which folders to be synchronized and the program make the synchronization. The sync can be in real time if the two computers are powered, or after few time when they are powered. Or it can lock another computer synced folder till update is required. At all this is my documents that I want to be synced in all my computers and to be changed from where I want. In fact I can move the updates with flash but if some program save the changes and make them on another computer with one click it will facilitate my work.

  Read the article

• Why do disk images hosted on a read-only HFS+ partition behave differently?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Boot Camp driver package includes file system drivers that enable Windows to access the Mac OS HFS+ partition. It's read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• Files deleted. What could have happened?

  - by jjfine

  I'm having a weird issue today. I was writing and testing out some simple cgi scripts this morning when I realized that I couldn't run them from one of the other computers on the (windows) network. So I had my network admin come in and take a look at what was going on. A few minutes later a co-worker came in and told me that a bunch of files he was working with as well as a bunch of others (all *.c files) on the network drive got deleted. He also noticed some strange apache_dump_500.log.txt files in the same directories where the files got deleted. The apache_dump_500.log.txt files all look like this: REDIRECT_HTTP_ACCEPT=*/*, image/gif, image/x-xbitmap, image/jpeg REDIRECT_HTTP_USER_AGENT=Mozilla/1.1b2 (X11; I; HP-UX A.09.05 9000/712) REDIRECT_PATH=.:/bin:/usr/local/bin:/etc REDIRECT_QUERY_STRING= REDIRECT_REMOTE_ADDR=<my computer's local ip> REDIRECT_REMOTE_HOST= REDIRECT_SERVER_NAME=<my computer's domain url> REDIRECT_SERVER_PORT= REDIRECT_SERVER_SOFTWARE= REDIRECT_URL=/cgi-bin/trojan.py I looked and I don't have any trojan.py in my cgi-bin folder. And all my apache logs are clean. Windows event logger seems to not have any traces of what happened either. My httpd.conf: http://pastebin.com/Yny2Yh8v I think we've got some kind of virus that added this trojan.py file to my cgi-bin, ran the script, and deleted the script and any traces from the logs. Is this a thing that happens? Any ideas whatsoever would be much appreciated!

  Read the article

• Power issues Foxconn Barebones kit

  - by alpha1

  I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

  Read the article

• Internet Explorer not working after establishing a SSTP VPN connection

  - by Massimo

  I have a problem which is constantly appearing on each Windows 7 computer I'm using, whenever I establish a SSTP VPN connection to a ForeFront TMG 2010 firewall; it only happens with SSTP connections, not PPTP/L2TP ones. The problem appears only if using a proxy server for Internet access; it doesn't happen when directly accessing the Internet (with or without NAT). It doesn't seem to depend on a specific proxy software being used (I've seen it happening with various ones). The problem is: as soon as I start the VPN connection, Internet Explorer can't access anything anymore. I'm not using the VPN connection as a default gateway, and I can succesfully ping the proxy server after the VPN connection is esatablished (and even telnet to its 8080 TCP port), so this is definitely not a routing problem. Also, the problem is specifically related to Internet Explorer: while it seems not able to connect to any site, other programs (such as FireFox) have no problem accessing the Internet through the same proxy. This behaviour can be easily reproduced on any Windows 7 computer (the service pack and patch level doesn't seem to matter at all). Have IE connect through a proxy, establish a SSTP VPN connection... and IE will just not work anymore until the VPN connection is dropped.

  Read the article

• Super slow opening my downloads folder

  - by Mark

  I have an exe file in my download folder that I half downloaded through utorrent (it's not piracy, a legit file from people who use bittorrent to distribute large files). I think I tried to open it while it was still sharing, that is, did not stop the upload. That actually froze my computer. When I restart in utorrent I set the file to be deleted. Unfortunately even though utorrent doesn't see that file anymore, it's still visible in my download folder. Whenever I try to open my download folder it literally takes 10 minutes or more. It opens, but is empty and the blue progress bar needs a long time to complete. After completion I can use the download folder normally, but opening and closing things in that folder takes a long time. I see the exe that I tried to download. I tried to delete it. But it was taking so long 30+ minutes that I eventually just hit cancel. That doesn't even work, and it was slowing down the computer. Couldn't figure out how to stop the delete so I just pulled the plug. Should I just forget about that dl folder and set a new one? Is there something I can do? Thanks.

  Read the article

• How do you enable view source in ie8 when it gets magically diabled

  - by Tim Meers

  I have multiple computers that all seem to have View Source disabled from the content menu when you right click on a web page. Now I know it's not that the web page is some how disabling it, I'm pretty sure thats not even possible. But alas I have at least 3 machines in my office (not on AD) that have this problem. I have also worked on clients computers that have this same issue. It's down right maddening! I tried to Google for it, but it just shows results from the dawn of IE6 in all of it's "glory" with a bug where if the cache was full it would be disabled. But this is not the case in IE8. Any body have a clue why this is happening, or a fix for it? Maybe a reg setting? Update: So I got a little closer to solving it, but there was still an issue on one computer where it allowed it not is HTTP, but not in HTTPS. One other computer works correctly in both. I Found these two keys missing in the registry: [-HKEY_CURRENT_USER\SOFTWARE\Microsoft\Internet Explorer\View Source Editor] [-HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Internet Explorer\View Source Editor]

  Read the article

• Wake on Demand for Apache server in OS X 10.8

  - by Gary

  Mac OS X Mountain Lion does not have a Web Sharing box in the Sharing system prefs menu. It is thoroughly discussed on the web that the Apache server is available, and that it can be turned on manually in the command line, or by using a convenient Prefs Pane. That works while the computer is awake. But, when my computer goes to sleep, the server stops working, even though Wake for Network Access is checked in the Energy Saver Pref Pane. From the discussion on Bonjour, I see that this problem probably results from the fact that Apache isn't registered with Bonjour. Does that sound likely? If not, please make some suggestions. The connection is via hard-wired ethernet. If registration with Bonjour is the problem, I'd like to know how to register it. You gave a nice description of dns-sd, and the command description says dns-sd -R Name Type Domain Port [TXT...] (Register a service)", but I don't know what to use for "Name" or "Type", or the format of the domain. I tried some dns-sd -B searches and found nothing I could use as a model, and it doesn't show up in Bonjour Browser. Any suggestions would be appreciated.

  Read the article

• Dell XPS 1530 DVD-RW firmware problem

  - by josecortesp

  Hello everyone. I have this XPS laptop since a year and a half ago. About 2 months ago, with the waranty expired, i tried to run the optiarc slot load DVD-RW firmware update, and said everything was okay. Then I restarted it and the problem started: Now, every single time I turn on my computer, it get stuck at the BIOS POST until the drive sounds like "ready" and then the computer starts normally. And this happen EXACTLY the same when it's getting back from sleep. I'm pretty sure is not a software issue, because I tried with Vista Home Premiun 32 bits, Ubuntu (from 8.10+)32 & 64, and with W7 64. Already tried to run the firmware installer like a million time, in case it is a failing install with no luck. Also, google it to see if someone has the same problem, and again, no. The Drive performs pretty okay once the System is on, but waiting to the drive to be ready everytime is really annoying. The Firmware I updated was this, and the drive is: K937C Assembly, Dvd+/-rw, 8, SLOT, 1530 Sony Nec Optiarc Inc. I'll apreciate any help you can give me

  Read the article

• Windows media scaling/interpolation method

  - by MichaelH

  Usually in Windows, if videos or other media is upscaled from a certain resolution to a higher resolution (e.g. "monitor size"), a bilinear filtering algorithm or similar is used, such that the upscaled material doesn't look blocky. On my system however, the used interpolation algorithm changed from 'bilinear' to 'nearest neighbor' at some point, with the effect that upscaled videos (e.g. viewed in MPC or WMP, and also Skype video streams) and games (e.g. from PopCap) appear rather blocky. Not sure what the common factor between those is, could be DirectShow(?). I am not aware of having changed any setting that could have affected this state, in fact I am not even aware such a setting exists. I'm guesing that some installed software must have changed something on my computer. My computer is running Windows 7, but I had already experienced the same effect on an XP machine some while ago, where it changed back again to the more pleasing bilinear interpolation after a while, as magically as the first time. What could be wrong with this installation, and how can I change this upscaling interpolation behavior?

  Read the article

• I can't get my PC to start up by a normal way.

  - by ssice

  I couldn't write a more accurate title. I am just unable to start the computer by pressing the Power On button. I checked the Power Supply and it seems to give good voltage values in every pin. And this is not a BIOS malfunction because of bad overclocking or anything that may come to your mind. And I will tell you why. It happens that EPS (or any ATX-based) power supply has the ability to be powered-on by the Motherboard by jumping the 13th pin of the 24-pin-ATX-connector to COM/GND. I did it, after pushing the power on button (without any visual response) and, pwhaa! The machine turned on. I was able to read (and even write, if I wanted) BIOS values and then start any OS installed. Machine starts, so it's not any kind of misconfiguration. It seems some hardware related. I am able to power the machine on only if I already pushed the power on button. Though pushing it without jumping the 13th pin to ground for a second does not power the machine. Of course, jumping the pin without pushing the power on button does not tell the motherboard anything, so the computer would not start up either. It's as if the logic that connects the power button with the 13th pin derivation to GND was unable to be activated. What can be the issue? How can I solve it? My configuration is as follows: CPU: AMD Phenom 9850 X4 Black Edition MB: ASUS Formula II AM2 RAM: 2x2GB Corsair Dominator 5-5-5-15 2T @ 1066MHz DDR2 Tested also with only 1 module GPU: 2x XFX nVIDIA GeForce 9600 GT XxX Alpha Dog Edition @ Core: 540Mhz [SLi] Power Supply: Xilence 700W (ATX 12V 2.3 / EPS 12V 2.92 compatible) PS: I know the machine is like 2 years old. I hardly use it now, but my parents do.

  Read the article

< Previous Page | 380 381 382 383 384 385 386 387 388 389 390 391  | Next Page >