Search Results

Search found 12184 results on 488 pages for 'named parameters'.

Page 386/488 | < Previous Page | 382 383 384 385 386 387 388 389 390 391 392 393  | Next Page >

• CentOS 5.5 remote kickstart installation stalls at "Starting install process." How to debug?

  - by ewwhite

  Hello, I'm having a difficult time with a remote CentOS 5.5 kickstart installation on an HP ProLiant DL360 G6. This is in an environment where I maintain an internal CentOS yum repository. The kickstart installation and post scripts have been tested and normally work. This hardware is also common in this environment, so I do not believe that it is a factor. Unfortunately, I'm having problems with a specific server install. The system is remote to the yum repository at a distance of 500 miles. They are connected over a private low-latency 100-megabit layer 2 connection (26ms round-trip). I'm mounting the 10mb CentOS 5 netinstall ISO image via an HP ILO remote console. The initial boot parameters are: linux ks=http://yum.abctrading.com/prop.cfg ksdevice=eth0 ip=x.x.x.x dns=x.x.x.x netmask=255.255.255.0 gateway=x.x.x.x I'm using the url --url http://ks.abctrading.com/5.5/os/x86_64/ method of installation. This quickly boots into the anaconda installer, pulls the kickstart config and formats the drives. The process eventually halts at the screen below, reading "Starting install process.". Going to the other virtual consoles give the second image below. The process stalls at this point and cannot proceed with the rest of the installation. Running the same kickstart config locally works just fine. I've tried mounting the boot ISO from the console as well as from the ILO2 command line pointing to a locally-hosted boot ISO via http. How can I debug this? Are there any options I've overlooked?

  Read the article

• Network to network VPN Centos 5

  - by Atul Kulkarni

  I am trying to follow "http://www.centos.org/docs/5/html/Deployment_Guide-en-US/ch-vpn.html#s1-ipsec-net2net" I have come up with the following On local router machine: in my ifcfg-ipsec0: ONBOOT=yes IKE_METHOD=PSK DSTGW=10.5.27.1 SRCGW=10.6.159.1 DSTNET=10.5.27.0/25 SRCNET=10.6.159.0/24 DST=205.X.X.X TYPE=IPSEC I have /etc/sysconfig/network-scripts/keys-ipsec0 file in place. On Remote Machine in the cloud if have /etc/sysconfig/network-scripts/ifcfg-ipsec1: TYPE=IPSEC ONBOOT=yes IKE_METHOD=PSK SRCGW=10.5.27.1 DSTGW=10.6.159.1 SRCNET=10.5.27.124/25 DSTNET=10.6.159.0/24 DST=38.x.x.x with its respective /etc/sysconfig/network-scripts/key-ipsec1 file. The DST in both cases are NAT'd external IPs. Is that a problem? I have made changes for port forwarding as well. When I try to bring the interfaces up it gives me output "RTNETLINK answers: Invalid argument". I am confused now and don't know what more to do? Any place I can digup what parameters were wrong? I really appreciate any help I can get. Thanks and Regards, Atul.

  Read the article

• RHEL 5.2 installing on ProLiant BL460c - hangs at 'now booting the kernel'

  - by Dr Rocket Mr Socket

  As the title states, I have a problem. This server and the installation disc are also on the other side of the world to me so... So far, I have tried to start the install with the parameters: linux text noapic noacpi no=apic no=acpi which results in the same hang. I have also disabled a PCI ethernet adapter, I am uneasy about disabling the onboard ethernet adapter I do not know if ILO uses this. Anyone have any advice? Much appreciated. EDIT: full output after trying to begin the installation. boot: linux text Loading initrd.img.................. Loading vmlinuz....... Uncompressing Linux...done. Now booting the kernel stays on this for hours EDIT2: adding the 'mem=40960M' (server has 40 gigs of ram) parameter allows it to proceed but the following output directly after 'Now booting the kernal' Memory: sized by int13 0e801h initrd extends beyond end of memory (0x00ef2090 > 0x00000000) disabling initrd Console: 16 point font, 400 scans Console: colour VGA+ 80x25, 1 virtual console (max 63) pcibios_init : BIOS32 Service Directory Structure at 0x000ffee0 pcibios_init : BIOS32 Service Directory entry at 0xf0000

  Read the article

• Samba4/Ubuntu Shares Incorrectly Available to All Users

  - by Dan

  I've got my Ubuntu server working with Samba4 and got it set up as the Primary domain controller on my network with AD and all that goodness. However, I'm trying to get my Samba configuration to work with the users and groups I've defined with the Active Directory tools from Windows. For instance, I've got a share X which I want users A and B (as part of the 'management' group, known as LLGrpManager in my setup) to see, but no body else. However, after making changes to the configuration, restarting Samba, I test by connecting to the share with my Mac over Samba as user 'C' which isn't part of the management group, and I can, incorrectly, see the X share. I've tried alsorts of combinations of specifying the group with no luck at all. I've got a feeling that my global config might be too lenient or something to do with file permissions but being a bit green, I'm without clue. My /etc/samba/smb.conf # Global parameters [global] server role = domain controller server string = Office Server workgroup = LLDOMAIN realm = lldomain.local netbios name = DUMBO passdb backend = samba4 logon path = \\%L\profiles\%U logon drive = L: log file = /var/log/samba/%m.log max log size = 50 security = ads domain logons = yes domain master = auto usershare allow guests = no valid users = %S [netlogon] path = /var/lib/samba/sysvol/lldomain.local/scripts read only = no guest ok = no [sysvol] path = /var/lib/samba/sysvol read only = No guest ok = no valid users = @LLDOMAIN\LLGrpManager [ShareX] path = /data comment = Entire Data Volume guest ok = no comment = Entire Data Volume guest ok = no valid users = @LLDOMAIN\LLGrpManager admin users = @LLDOMAIN\LLGrpManager browsable = no inherit acls = yes inherit permissions = yes ... My /etc/nsswitch.conf I've also instructed the system to use the nss winbind library when searching for users or groups by adding the stanza passwd and group in /etc/nsswitch.conf: passwd: compat winbind group: compat winbind shadow: compat Permissions on the folder in question drwxrwxrwt 8 root root 4.0K Oct 28 19:11 data

  Read the article

• Samba between Ubuntu server 10.10 and Windows Vista, Windows 7

  - by chepukha

  I have a linux box running Linux server ubuntu 10.10. I have installed Samba on this linux box and want to share files with my laptops which run Windows Vista home and Windows 7 home. I have been struggling with the setup for almost a month but couldn't get it right. If I try to access share folder from Windows Vista, I get message "Windows cannot access \\server_ip_address". Error code: 0x80070035. The network path was not found. If I access from Windows 7, then after entering password to login I can see the list of share folders on Linux box. But if I click on a share folder, I get the same error message as above. Tail /var/log/samba/log.windows7-pc I got the following message: [2011/03/16 00:17:41.427238, 0] smbd/service.c:988(make_connection_snum) canonicalize_connect_path failed for service sharemedia, path /root/sharemedia Here is my setting in smb.conf [global] share modes = yes netbios name = Samba workgroup = WORKGROUP wins support = yes encrypt passwords = true [sharemedia] comment = Tesing sharing using Samba path=/root/sharemedia/ public = yes valid users = samba_usr_name ; make sure all files are sensible permissions create mask = 0660 force create mask = 0660 directory mask = 2770 force directory mask = 2770 directory security mask = 0000 ; Normal share parameters read only = no browseable = yes writable = yes guest ok = no

  Read the article

• NTDS Replication Warning (Event ID 2089)

  - by Chris_K

  I have a simple little network with 3 AD servers in 2 sites. Site A has Win2k3 SP2 and Win2k SP4 servers, site B has a single Win2k3 SP2 server. All have been in place for at least 3 years now. Just last week I started getting Event 2089 "not backed up" warnings (example below) on both of the win2k3 servers. I understand what the message means, no need to send me links to the technet article explaining it. I'll improve my backups. What I'm more curious about is why did I just start getting this message now? Why haven't I been getting it for the past 3 years?!? Perhaps this is related: I recently decommissioned a few other sites and AD controllers (there used to be 3 more sites, each with their own controller). Don't worry, I did proper DCpromo exercises and made sure we didn't lose anything. But would shutting those down possibly be related to why I get this error now? This won't keep me awake at night but I am curious as to what changed... Event Type: Warning Event Source: NTDS Replication Event Category: Backup Event ID: 2089 Date: 3/28/2010 Time: 9:25:27 AM User: NT AUTHORITY\ANONYMOUS LOGON Computer: RedactedName Description: This directory partition has not been backed up since at least the following number of days. Directory partition: DC=MyDomain,DC=com 'Backup latency interval' (days): 30 It is recommended that you take a backup as often as possible to recover from accidental loss of data. However if you haven't taken a backup since at least the 'backup latency interval' number of days, this message will be logged every day until a backup is taken. You can take a backup of any replica that holds this partition. By default the 'Backup latency interval' is set to half the 'Tombstone Lifetime Interval'. If you want to change the default 'Backup latency interval', you could do so by adding the following registry key. 'Backup latency interval' (days) registry key: System\CurrentControlSet\Services\NTDS\Parameters\Backup Latency Threshold (days) For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• OpenVPN with MacOS X Client and same subnets in local and remote net.

  - by Daniel

  I have a homenetwork 192.168.1.0/24 with gteway 192.168.1.1 and a remote network with the same parameters. Now I want to create a OpenVPN tunnel between those networks. I have no problems with Windows, because Windows routes everything to 192.168.1.0/24 except 192.168.1.1 throught the tunnel. On MacOS X however I see the folling line in the Details window: 2010-05-10 09:13:01 WARNING: potential route subnet conflict between local LAN [192.168.1.0/255.255.255.0] and remote VPN [192.168.1.0/255.255.255.0] When I list the routes I get the following: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.1.1 UGSc 13 3 en1 127 localhost UCS 0 0 lo0 localhost localhost UH 12 3589 lo0 169.254 link#5 UCS 0 0 en1 192.168.1 link#5 UCS 1 0 en1 192.168.1.1 0:1e:e5:f4:ec:7f UHLW 13 17 en1 1103 192.168.1.101 localhost UHS 0 0 lo0 192.168.6 192.168.6.5 UGSc 0 0 tun0 192.168.6.5 192.168.6.6 UH 1 0 tun0 My Interfaces are en1 - My local Wifi network tun0 - The tunnel interface As can be seen from the routes above there is no entry for 192.168.1.0/24 that routes the traffic through the tunnel interface. When I manually route a single IP like 192.168.1.16 over the tunnel gateway 192.168.6.6, this works. Q: How do I set up my routes in MacOS X for the same behaviour as on windows, to route everything except 192.168.1.1 through the tunnel, but leave the default gateway to be my local 192.168.1.1 ?

  Read the article

• Tidy up old Windows Server Backup snapshots

  - by dty

  Hi, I'm running wbadmin from a scheduled job, backing up my C: and D: drives to my E: and (I believe!) including the system state: wbadmin start backup -backuptarget:e: -include:c:,d: -allCritical -noVerify -quiet I'd like to delete old backups, but I'm concerned that all the information I can find says to use wbadmin to delete old system state backups, and vssadmin to delete other backups. As far as I know, my backups ARE system state backups, but are using VSS on E: for storage, so I'm worried about trying either of these techniques for fear of losing all my backups. This is a home network, so I don't have a spare server to test this on. I'm also happy to simply restrict the space used on E:, but I can't make sense of the difference between the /for and /on parameters of the relevant vssadmin command. For reference, here's the output of vssadmin show shadows: Contents of shadow copy set ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Contained 1 shadow copies at creation time: 07/01/2011 08:12:05 Shadow Copy ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Original Volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Volume: \\?\GLOBALROOT\Device\HarddiskVolumeShadowCopy83 Originating Machine: x.y.com Service Machine: x.y.com Provider: 'Microsoft Software Shadow Copy provider 1.0' Type: DataVolumeRollback Attributes: Persistent, No auto release, No writers, Differential [... repeated a lot...] vssadmin show shadowstorage: Shadow Copy Storage association For volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 5.859 GB Shadow Copy Storage association For volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 40.317 GB Shadow Copy Storage association For volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 168.284 GB Allocated Shadow Copy Storage space: 171.15 GB Maximum Shadow Copy Storage space: UNBOUNDED wbadmin get versions: Backup time: 07/01/2011 03:00 Backup target: 1394/USB Disk labeled xxxxxxxxx(E:) Version identifier: 01/07/2011-03:00 Can Recover: Volume(s), File(s), Application(s), Bare Metal Recovery, System State [... repeated a lot...]

  Read the article

• sporadic routing to another website when opening a common url

  - by user226098

  I have a strange problem in our office: Sometimes when opening a url from one of our projects random url in any browser not the right website shows up but some other website. In most of the cases it redirects to google.com with some parameters like https://www.google.de/?gfe_rd=cr&ei=krOOU8_kGcSKswadyYDQBw&gws_rd=ssl or just the ugly google 404 page). But today it remains on the origial url but shows up the the content of http://debug.netdna-cdn.com/. This happens about 1 time a week and for no apparent reason. Even stranger it only occurs on a single pc in the network. It now happens on two different computers in the network. Both use windows 8. The problem cannot be fixed by clearing the browser cache but by rebooting the pc or using ipconfig /flushdns. So I think it has something to do with the dns cache of the machine. But I have no idea what the reason is for this and how i can figure out how to solve it. Any ideas?

  Read the article

• Setting Outlook Web Access as default mail client in Firefox

  - by Barton Chittenden

  The company that I work for is nice enough to let me use Linux for work, but they use Outlook. I've been using Outlook Web Access (OWA) as my mail client, which is more or less acceptable. The only problem is that whenever I click on a mailto link or use the "Send Link" menu option in firefox, I'm prompted to use evolution. Since connecting to an exchange server through evolution seems to be sketchy at best, I would like to set OWA as my default mail client. I'm using Firefox 3.6.13 Here's what I've found so far: Default mail client can be found at Edit Menu -> Preferences -> Applications Tab -> mailto When I click on the drop down menu, one of the options is "Application Details" This shows two options by default: Google Yahoo! Mail Each of these shows how to launch that service. For Gmail: https://mail.google.com/mail/?extsrc=mailto&url=%s For Yahoo!: http://compose.mail.yahoo.com/?To=%s I presume that Outlook Web Access has something similar. Based on the googling that I've done so far, I think that this should look something like this: https://<server name>/owa/?cmd=compose... A little experimentation on my part shows that the following will compose a message: https://<email server>/owa/?ae=Item&a=New&t=IPM.Note but I still don't know how to specify recipient, subject or body of the email to be composed... What I want to know is a) does anyone know the URL parameters to compose a mailto in Outlook Web Access, including subject, recipient and body? else b) can someone give me a decent pointer for where to get this information?

  Read the article

• CentOS Latency High Troubleshooting

  - by Sarah Weinberger

  I have two CentOS servers connected via a 10 Gb fiber optic cable with a network emulator connected between them. All three units sit on a desk in the lab. There is also a regular 1 Gbit Ethernet cable connected to each of the machines, which provide internet connectivity. When I set the latency to something roughly below 30 ms, all is fine. When the latency gets to 70ms and above, and definitely 130ms, the network layer suspends. For instance, if I set the latency (delay) to 70ms, then launching TeamViewer (or any other application that uses network connectivity) never happens or does not work. There is no timeout message, simply no response. I have to lower to latency back down to zero to see any response and have the box start working. What is the problem and how would I go about fixing it? It seems to me some sort of setting in Linux causes one of the CentOS networking drivers to sit in an infinite loop or something. eth0 is the connection to the internet, all settings are default eth2 is the 10 Gbit fiber optic connection to the other computer with the MTU set to 9600 with all other parameters at default values.

  Read the article

• qsub: How can I find out what DRM middleware exactly is installed on a cluster?

  - by gojira

  I have a user account on a very big cluster. I have previous experience with Grid Engine and want to use the cluster for array jobs. The documentation tells me to use "qsub" for load balancing / submission of many jobs. Therefore I assumed this means the cluster has Grid Engine. However all my Grid Engine scripts failed to run. I checked the documentation and it is a bit weird. Now I slowly suspect that this cluster does not actually have Grid Engine, maybe it's running something called Torque (?!). The whole terminology in the man pages is a bit weird for me as a Grid Engine user, for example they talk about "bulk jobs" instead of "array jobs". There is no referral to variables on which I rely on, like SGE_TASK_ID etc. Instead they refer to variables starting with PBS_. Still, there are qsub and qstat commands. Also qsub behaves differently, apparently it is not possible to specifiy the command line parameters with bash-script comments etc. There is a documentation for the cluster system, but it does not say what the DRM middleware actually is - it refers to the entire DRM system simply as "qsub". I tried qsub --version qsub: 1.2 2010/8/17 I am not sure what I am actually running when I invoke qsub on that cluster! My question is, how can I find out if I am running Grid Engine or Torque (or whatever it is), and which version?

  Read the article

• How to test nginx proxy timeouts

  - by mkorszun

  Target: I would like to test all Nginx proxy timeout parameters in very simple scenario. My first approach was to create really simple HTTP server and put some timeouts: Between listen and accept to test proxy_connect_timeout Between accept and read to test proxy_send_timeout Between read and send to test proxy_read_timeout Test: 1) Server code (python): import socket import os import time import threading def http_resp(conn): conn.send("HTTP/1.1 200 OK\r\n") conn.send("Content-Length: 0\r\n") conn.send("Content-Type: text/xml\r\n\r\n\r\n") def do(conn, addr): print 'Connected by', addr print 'Sleeping before reading data...' time.sleep(0) # Set to test proxy_send_timeout data = conn.recv(1024) print 'Sleeping before sending data...' time.sleep(0) # Set to test proxy_read_timeout http_resp(conn) print 'End of data stream, closing connection' conn.close() def main(): s = socket.socket(socket.AF_INET, socket.SOCK_STREAM) s.setsockopt(socket.SOL_SOCKET, socket.SO_REUSEADDR, 1) s.bind(('', int(os.environ['PORT']))) s.listen(1) print 'Sleeping before accept...' time.sleep(130) # Set to test proxy_connect_timeout while 1: conn, addr = s.accept() t = threading.Thread(target=do, args=(conn, addr)) t.start() if __name__ == "__main__": main() 2) Nginx configuration: I have extended Nginx default configuration by setting explicitly proxy_connect_timeout and adding proxy_pass pointing to my local HTTP server: location / { proxy_pass http://localhost:8888; proxy_connect_timeout 200; } 3) Observation: proxy_connect_timeout - Even though setting it to 200s and sleeping only 130s between listen and accept Nginx returns 504 after ~60s which might be because of the default proxy_read_timeout value. I do not understand how proxy_read_timeout could affect connection at so early stage (before accept). I would expect 200 here. Please explain! proxy_send_timeout - I am not sure if my approach to test proxy_send_timeout is correct - i think i still do not understand this parameter correctly. After all, delay between accept and read does not force proxy_send_timeout. proxy_read_timeout - it seems to be pretty straightforward. Setting delay between read and write does the job. So I guess my assumptions are wrong and probably I do not understand proxy_connect and proxy_send timeouts properly. Can some explain them to me using above test if possible (or modifying if required).

  Read the article

• Tomcat6 getting crashed at regular intervals installed in Ubuntu

  - by Milesh Rout

  I have installed Tomcat6 in Ubuntu OS and when I run my web application the server gets crashed at regular intervals. I have tried a lot but not getting the solution. I have increased the memory upto 2048mb but still getting such error. Following is the error I am getting. Any help would be really appreciated. org.apache.tomcat.util.http.Parameters processParametersINFO: Invalid chunk starting at byte [312] and ending at byte [312] with a value of [null] ignoredException in thread "Timer-1" Exception in thread "com.mchange.v2.async.ThreadPoolAsynchronousRunner$PoolThread-#0" Exception in thread "com.mchange.v2.async.ThreadPoolAsynchronousRunner$PoolThread-#2" Exception in thread "com.mchange.v2.async.ThreadPoolAsynchronousRunner$PoolThread-#1" Exception in thread "Timer-2" Exception in thread "http-8080-4" Exception in thread "http-8080-8" Exception in thread "http-8080-17" Exception in thread "org.hibernate.cache.StandardQueryCache.data" Exception in thread "org.hibernate.cache.UpdateTimestampsCache.data" Exception in thread "org.hibernate.cache.StandardQueryCache.data" Exception in thread "org.hibernate.cache.StandardQueryCache.data" Exception in thread "org.hibernate.cache.UpdateTimestampsCache.data" Exception in thread "org.hibernate.cache.StandardQueryCache.data" Exception in thread "org.hibernate.cache.StandardQueryCache.data" Exception in thread "org.hibernate.cache.UpdateTimestampsCache.data" Exception in thread "com.safenet.usermgmt.User.data" Exception in thread "http-8080-7" Exception in thread "http-8080-12" Exception in thread "http-8080-16" Exception in thread "http-8080-14" Exception in thread "http-8080-13" Exception in thread "http-8080-15" Exception in thread "http-8080-6" OpenJDK Client VM warning: Exception java.lang.OutOfMemoryError occurred dispatching signal SIGTERM to handler- the VM may need to be forcibly terminated

  Read the article

• TFTP Timing Out on Ubuntu VM

  - by valsidalv

  I'm running a Windows 7 PC with VMware installed which has my Ubuntu (10.04 Lucid Lynx). I recently installed a DHCP server and TFTP (Xinet tftpd) using these instructions. I've mapped a network drive so that my Windows has access to all the files in my VM through a 192.x.x.x IP address. I'm trying to throw some custom firmware onto a router. The router has its own built-in TFTP utility that will download the image. It successfully manages to do everything but it is slow because it writes it to flash memory. There is another method that is much quicker because it writes to RAM directly but it must use the TFTP server in Ubuntu. The issue I'm facing is that the Ubuntu TFTP transfer seems to be timing out. The transfer starts but never goes past ~60%. Here's my /etc/xinetd.d/tftp file (similar to a known working config): service tftp { protocol = udp port = 69 socket_type = dgram wait = yes user = nobody server = /usr/sbin/in.tftpd server_args = -s /home/user/tftp/ disable = no cps = 300 2 per_source = 60 } I've done some searching but can't find any parameters for this file to control timeout time or number of retries. The last two arguments (cps, per_source) and completely alien to me (can anyone explain). I have a few possible solutions but the easiest would be to get this TFTP server working. Can anyone help? Either with a timeout configuration or maybe even recommend a different TFTP server? Thanks!

  Read the article

• How to pass alias through sudo

  - by Tanktalus

  I have an alias that passes in some parameters to a tool that I use often. Sometimes I run as myself, sometimes under sudo. Unfortunately, of course, sudo doesn't recognise the alias. Does anyone have a hint on how to pass the alias through? In this case, I have a bunch of options for perl when I'm debugging: alias pd='perl -Ilib -I/home/myuser/lib -d' Sometimes, I have to debug my tools as root, so, instead of running: pd ./mytool --some params I need to run it under sudo. I've tried many ways: sudo eval $(alias pd)\; pd ./mytool --some params sudo $(alias pd)\; pd ./mytool --some params sudo bash -c "$(alias pd)\; pd ./mytool --some params" sudo bash -c "$(alias pd); pd ./mytool --some params" sudo bash -c eval\ "$(alias pd)\; pd ./mytool --some params" sudo bash -c eval\ "'$(alias pd)\; pd ./mytool --some params'" I was hoping for a nice, concise way to ensure that my current pd alias was fully used (in case I need to tweak it later), though some of my attempts weren't concise at all. My last resort is to put it into a shell script and put that somewhere that sudo will be able to find. But aliases are soooo handy sometimes, so it is a last resort.

  Read the article

• How to install/configure ffmpeg to compress mp4 videos for flash player delivery?

  - by Andrew Fulton

  We have a flash web-app that created interactive video, and are using ffmpeg to do some compression/resizing when a user "publishes" their project. The user can upload flv files and mp4 files, both of which play fine in the Flash UI before publishing. After publishing the flv files work fine, but the mp4 files will not play in the flash player: Audio will play but video won't. The mp4 files will play fine if I download them and play them in the Quicktime player but if I attempt to open them in the Adobe Media Player it reports "The media file does not contain a supported video track". If I open the Movie inspector in quicktime it tells me that the original file is an "h264" video and the ffmpeg-processed ones are "mpeg-4". I have tried forcing it to h264 by adding flags like -f h264 and -vcodec h264 but I get a screenfull of errors (no frame, illegal POC type, sps_id out of range) ending with Could not find codec parameters (Video: h264) h264 will show up if I run ffmpeg -formats and ffmpeg -codecs, and as I said it will play fine in Quicktime. Is there anything else I need to do to convince the flash player to play them? Is there anything else I need to tell you about the server that will help?

  Read the article

• trouble shooting ntfs-loop-xen combination in wubi based grub of Ubuntu

  - by Registered User

  Here is a situation I installed Ubuntu on a laptop using Wubi in Windows 7 drive.*The laptop is not mine.*I have installed and things worked by now perfectly without any problem.We are trying to set up a Xen (virtualization)environment in this laptop. After setting up every thing cleanly.When I needed to boot with following grub entries menuentry "Xen Linux 2.6.32.27" { insmod ntfs set root='(hd0,2)' loopback loop0 /ubuntu/disks/root.disk set root=(loop0) multiboot /boot/xen.gz module /boot/vmlinuz-2.6.32.27 dummy=dummy root=/dev/sda2 loop=/ubuntu/disks/root.disk ro console=tty0 module /boot/initrd.img-2.6.32.27 } I got error file not found error unknown command 'multiboot' error unknown command 'module' error unknown command 'module' Now to dig this issue further I reboot the machine and go to grub command prompt and manually pass on each of the above parameters which you see in the grub entry when I reached grub> insmod multiboot then I got following message on screen error:file not found. It looks like this wubi+ grub setup has just enough modules to use loopback file on ntfs, but the ACTUAL /boot directory is on the loopback NOT ntfs (hd0,2). Therefore any attempt to read any files from (hd0,2) simply wont work, cause there's no file there.I need to use insmod multiboot and command multiboot and module which are available in grub on a normal install without Wubi.But since the laptop is not mine so I am not allowed to partition it and have to make it work in this situation only. While a normal Kernel is still booting? How can I get module multiboot in this Wubi based install.

  Read the article

• Kickstart: Serve dynamic kickstart images via a CGI or PHP script?

  - by Stefan Lasiewski

  I'd like to kickstart a couple dozen RHEL6/SL6 servers. However, some of these servers are different and I don't want to create a new ks.cfg file for each class of server. Are there any products which can generate a Kickstart file dynamically on the fly, from a template? For example, if I append a line like this to the KERNEL: APPEND ks=http://192.168.1.100/cgi-bin/ks.cgi Then the script ks.cgi can determine what host this is (Via the MAC address), and print out Kickstart options which are appropriate for that host. I could optionally override some options by passing parameters to the script, like this: APPEND ks=http://192.168.1.100/cgi-bin/ks.cgi?NODETYPE=production&IP=192.168.2.80 After we kickstart the server, we activate Cfengine/Puppet on this system and manage the system using our favorite Configuration Management product. We're experimenting with xCAT but it is proving too cumbersome. I've looked into Cobbler, but I'm not sure it does this. Update: A roll-your-own solution is discussed in the O'Reilly book: Managing RPM-Based Systems with Kickstart and Yum, Chapter 3. Customizing Your Kickstart Install Dynamic ks.cfg, which echos some of the comments in this thread: To implement such a tool is beyond the scope of this Short Cut, but I can walk through the high-level design. Any such solution would mix a data store (the things that change) with a templating solution (the things that don’t change). The data store would hold the per-machine data, such as the IP address and hostname. You would also need a unique identifier, perhaps the hostname, such that you could pick up a given machine’s data. The data store could be a flat file, XML data, or a relational database such as PostgreSQL or MySQL. In turn, to invoke the system, you pass a machine’s unique identifier as a URL parameter. For example: boot: linux ks=http://your.kickstart.server/gen_config?host-server25 In this example, the CGI (or servlet, or whatever) generates a ks.cfg for the machine server25. But where, oh where, is the code for ks.cgi?

  Read the article

• WebDav System Error 67 in Windows XP

  - by Nixphoe

  Issue: I'm having issues getting WebDav to work in the command line on Windows XP, both Service Pack 2 and Service Pack 3. C:\>net use z: https://mywebsite.com/software/ System error 67 has occurred. The network name cannot be found. I have tested this with two webdav server. Both Ubuntu Apache and I Windows Server 2003 IIS. Both get the same result. Things That Haven't Worked: I've installed the following Microsoft KB on my XP machines with no avail. I've also found the following reg key: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\WebClient\Parameters UseBasicAuth REG_DWORD 1 I try the following when trying to use a few work around I've dug up on the web, all producing the same result. net use z: https://mywebsite.com/software net use z: https://mywebsite.com/software# net use z: https://mywebsite.com/software/ net use z: https://mywebsite.com/software/# I've also tried all the above combinations adding a user into it /user:user and /user:user@domain. I've also tried using http:// rather than https://. I've tried "\\server.com@ssl:443\folder" I've gone over networking related issues as @WesleyDavid had pointed out. Things that do work: I can connect to the webdav folder via the URL and with mapping in Network Place, with XP. But the command line doesn't work (I need a drive letter). Windows 7 works perfectly with the same command. My Delemma: I need this to work with a drive letter. What else can I try to get this working?

  Read the article

• Solaris 10 invalid ARP requests from 0.0.0.0? Link up/down every hour or 2

  - by JWD

  The guys at the data center where I'm hosting a server running Solaris 10 are telling me that my server is making a lot of invalid arp requests. This is an example of a portion of what was sent to me from the logs (with Mac addresses and IP addresses changed). [mymacaddress]/0.0.0.0/0000.0000.0000/[myipaddress]/[Datestamp]) It's being logged every hour. I don't see anything in the arp tables (arp -a) or routing tables (netstat -r) and I don't see anything relating to 0.0.0.0 when snoping the arp requests. The only place I see any reference to 0.0.0.0 is if I do netstat -a for the SCTP SCTP: Local Address Remote Address Swind Send-Q Rwind Recv-Q StrsI/O State ------------------------------- ------------------------------- ------ ------ ------ ------ ------- ----------- 0.0.0.0 0.0.0.0 0 0 102400 0 32/32 CLOSED But not really sure what that means. Doesn't seem like I can disable SCTP. There are some tunable SCTP parameters but it's not something I'm familiar with. Do I have to add changes to /etc/system? Looks like sctp_heartbeat_interval might be what I need to change? If it makes any difference, I have a few solaris zones running on this server, each with their own IP address on a virtual interface. eth0:0, eth0:1, etc. Does anyone have any idea what might be causing this and how to stop it? I think the switch I'm connected to doesn't like it and momentarily drops the connection. Is there anyway to at least block those requests using ipfilter or something else? Update: This was happening more frequently but now it seems to be happening roughly every hour or every two hours. It's not consistent. I tried setting setting the link speed and duplex to match the switch port and that seemed to make it stop happening for a few hours but then it started again.

  Read the article

• Using virtualization infrastructure for J2EE application distribution- viable alternative?

  - by Dan

  Our company builds custom J2EE web solutions. At the moment, we use standard J2EE distribution mechanisms (ear/war archives). Application servers are generally administered by our clients' IT departments and since we do not have complete control over the environment, a lot of entropy can be introduced into the solution. For example: latest app. server patch not applied conflicting third party libraries inside the app. server root server runtime and tuning parameters not configured (for example, number of connections in database pool) We are looking into using virtualization infrastructure for J2EE application distribution. Instead of sending the ear/war archive, we’d send image with application server node and our application preinstalled. Some of the benefits are same as using with using virtualization infrastructure in general, namely better use of hardware resources. For us, it reduces the entropy of hosting infrastructure - distributing VM should be less affected by hosting environment. So far, the downside I see can be in application server licenses, here they will have to use dedicated servers for our solution, but this is generally already done that way. Also, there is a complexity with maintaining virtualization infrastructure, but this is often something IT departments have more experience with than with administering and fine-tuning J2EE solutions. Anyone has experience with this model? What are the downsides? Will we not just replace one type of complexity with other?

  Read the article

• samba joined to AD canot see users when in the security tab on client

  - by Jonathan

  I've got samba joined via kerberos and winbindd to our AD network and user authentication and everything else is working great. However when I try to add users/groups to file permissions it tells me they are not found. All the users groups show up fine with getent so I'm not sure why they are not showing up. Here is my smb.conf and I would much appreciate any help with this. #GLOBAL PARAMETERS [global] socket options = TCP_NODELAY IPTOS_LOWDELAY SO_KEEPALIVE SO_RCVBUF=11264 SO_SNDBUF=11264 workgroup = [hidden] realm = [hidden] preferred master = no server string = xerxes web/file server security = ADS encrypt passwords = yes log level = 3 log file = /var/log/samba/%m max log size = 50 printcap name = cups printing = cups winbind enum users = Yes winbind enum groups = Yes winbind use default domain = Yes winbind nested groups = Yes winbind separator = + winbind refresh tickets = yes idmap uid = 1600-20000 idmap gid = 1600-20000 template primary group = "Domain Users" template shell = /bin/bash kerberos method = system keytab nt acl support = yes [homes] comment = Home Direcotries valid users = %S read only = No browseable = No create mask = 0770 directory mask = 0770 force create mode = 0660 force directory mode = 2770 inherit owner = no [test] comment = Test path=/mnt/test writeable=yes valid users = %s create mask = 0770 directory mask = 0770 force create mode = 0660 force directory mode = 2770 inherit owner = no [printers] comment = All Printers path = /var/spool/cups browseable = no printable = yes

  Read the article

• On Windows 2008 R2, how do I back up DHCP if the DHCP .mdb database is always busy?

  - by johnny

  I get this from my backup software. C:\WINDOWS\system32\dhcp\dhcp.mdb : The process cannot access the file because it is being used by another process. C:\WINDOWS\system32\dhcp\j50.log : The process cannot access the file because it is being used by another process. C:\WINDOWS\system32\dhcp\j50tmp.log : The process cannot access the file because it is being used by another process. C:\WINDOWS\system32\dhcp\tmp.edb : The process cannot access the file because it is being used by another process. My questions: Should I be doing a manual backup of DHCP via command line tools or maybe with MMC, Action, Backup before I run my backup? Is the %SystemRoot%\System32\DHCP\Backup directory always kept up to date? (which does get backed up by backup software) I'm answering my own question but the registry key is set up for 3c, 60 minutes, I believe. HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\DHCPServer\Parameters\BackupInterva This is not the included backup software for Windows. It is another product, but I have seen this with every backup software I've ever used.

  Read the article

• ubuntu 10.04 + php + postfix

  - by mononym

  I have a server I am running: Ubuntu 10.04 php 5.3.5 (fpm) Nginx I have installed postfix, and set it to loopback-only (only need to send) The problem is it is not sending. if i issue (at command line): echo "testing local delivery" | mail -s "test email to localhost" [email protected] I get the email no problem, but through PHP it does not arrive. When I send it via PHP, mail.log shows: Mar 28 10:15:04 host postfix/pickup[32102]: 435EF580D7: uid=0 from=<root> Mar 28 10:15:04 host postfix/cleanup[32229]: 435EF580D7: message-id=<20120328091504.435EF580D7@FQDN> Mar 28 10:15:04 host postfix/qmgr[32103]: 435EF580D7: from=<root@FQDN>, size=1127, nrcpt=1 (queue active) Mar 28 10:15:04 host postfix/local[32230]: 435EF580D7: to=<root@FQDN>, orig_to=<root>, relay=local, delay=3.1, delays=3/0.01/0/0.09, dsn=2.0.0, status=sent (delivered to maildir) Mar 28 10:15:04 host postfix/qmgr[32103]: 435EF580D7: removed any help appreciated, my main.cf file: smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = FQDN alias_maps = hash:/etc/aliasesalias_database = hash:/etc/aliases myorigin = /etc/mailname #myorigin = $mydomain mydestination = FQDN, localhost.FQDN, , localhost relayhost = $mydomain mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = loopback-only virtual_alias_maps = hash:/etc/postfix/virtual home_mailbox = mail/

  Read the article

< Previous Page | 382 383 384 385 386 387 388 389 390 391 392 393  | Next Page >