Search Results

Search found 12826 results on 514 pages for 'third party controls'.

Page 388/514 | < Previous Page | 384 385 386 387 388 389 390 391 392 393 394 395  | Next Page >

• What does opening a serial port do?

  - by reve_etrange

  What does opening the standard PC serial port do, in electrical terms (i.e. what voltages on which pins)? For example, the ancient VB6 program which controls an apparatus I am tasked with maintaining toggles .PortOpen to control some TTL. The connection only used 2 pins (bad solders fell apart), so which pins do I solder to? The only labels / documentation refer to pins 7 and 9, saying 0V and 5V parenthetically, but does .PortOpen really just put 5V between RI and RTS?. As a post script, this isn't the weirdest thing about the set up. The TTL I referred to above also connects to an instrument via a BNC to DB9 (!), with only 1 pin used. I guess there was an assumption about a common ground, since the BNC shielding isn't connected to the GND pin? The connection is to the instrument's 'foot pedal' pin, it was a way to remotely trigger the device. Update According to this page, the DTR and RTS pins can go high when the port is opened. If they were so configured, they will subsequently go low when the port is closed. If DTR and RTS are not enabled, opening the port should set both to low (and keep them low).

  Read the article

• pptp server 2003 hands out gateway from nic not dhcp server

  - by Pete

  I have created a pptp RRAS server for a handful of clients to connect to. I would like them to use the servers default gateway (.1) for internet access. They are able to successfully connect (& see LAN) but it then cuts them off the internet. I understand that all internet traffic would be routed through the pptp server but that's ok since I have enough pipe. The problem seems to be that: the clients gateway shows as their assigned RAS ip. The clients assigned DNS settings seem to be what is set to the servers nic not what I have specified in dhcp (which is the same server). DHCP relay agent properties points to the nic DHCP is running on (192.168.100.163). .1 is gateway in nic hw properties & dhcp. I have different dns secondary & third entries on my nic properties than what dhcp is configured for. The problem is that I have a 10.10.1.x network that people can not see if they uncheck the gateway option but, they are then unable to see our other hosted sites on the internet.

  Read the article

• Configure linux machine as bridge/switch and end device

  - by leemes

  At my home, I have two desktop PCs in two rooms. The router / DSL modem is in one of these rooms. Now I want to configure a home server (having 2 LAN ports, running 24/7) in the corridor between the two rooms, using only one LAN cable at each door. This gives me the following physical configuration: (door) (door) .----/-/----. .-----/-/----------._ FritzBox | | | .----´´ DSL Router PC1 Server | PC2 As just said, the server has 2 network interfaces and is running Ubuntu. What I need now is a network configuration which enables both the server and PC1 to connect to the router. I think the server needs to serve as a bridge or switch. Currently, all computers are configured having static IP addresses. If I'm understanding it correctly, a bridge / switch doesn't have its own IP address, but as the server needs to be configured as an own end device, it needs to have one. My first question is, do I have to configure both interfaces separately, giving both the same static IP address? My next question is, how do I bridge the two physical networks into one? I have basic understanding (but am always confused again and again) of bridges and switches, but I don't know how to configure it in software. I only know that it's possible to do so :) The third question is: Is it possible to configure this in a way that network packets from/to PC1 to/from the router only go through hardware or only consume low CPU in the server? Can you help me? Thanks in advance!

  Read the article

• Help with Ubuntu and Windows, separate HDs

  - by LuxuryMode

  Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. I have some pictures of boot up: first one is strange error i get after messing with CMOS to finally get ubuntu install to work. http://imgur.com/5sqJa then boot menu: http://imgur.com/TWtLq then error: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu.

  Read the article

• How to monitor bandwidth use of each device on wifi network

  - by GWLlosa

  I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• GIT Website Deployment

  - by Brian

  I am attempting to setup GIT to deploy my project to different locations based on the branch. (I think this is what I want to do anyway). My current setup is this: Local dev machine running Netbeans to make changes. Remote server hosting GIT projects (same server running apache) - 2 subsites exist a test.FQDN.com and a live.FQDN.com What I would like to do is have 1 GIT project (MyProject) and create a new feature branch. Any commits done to the new feature branch would push to test.FQDN.com. Once the features have been tested and then merged into the master branch, it would push to live.FQDN.com. I have looked at GIT's post-receive hooks and was able to use "git checkout -f" command to pull on the test.FQDN.com site however that only pulls the master branch and not the new feature branch. I do not have any funding to use a third party to make this work, and would prefer to stay within GIT but have full root access to the web server if there is a package to install which would help control this. Any suggestions would be great!

  Read the article

• Server 2003 and SSL Certificates

  - by Keith Stokes

  I have a Windows 2000 domain with dozens of Windows 2000 servers and a few 2003 servers. Each server runs a custom app talking to a 3rd party utilizing self-signed certificates. To help troubleshooting we've created a custom test app. The 2000 servers are able to talk within seconds. The 2003 servers take anywhere from 10-30 seconds using a domain account and much less, usually under 5 seconds using a local account. The only exception to the local account performance is a new account, which is slow initially then faster. If you leave the test app open and reconnect repeatedly it talks in seconds. If you leave it open for sometime between 1 and 2 hours, it reverts back to the previous 10 seconds, so obviously something is caching. Installing the destination certificates in the local 2003 server store makes no difference. I've installed the certificates in AD and that apparently makes domain accounts work in 9-12 seconds, vs 30 seconds that was regular before. Manually clearing the certificate store on the 2003 server makes no difference. I'm at a loss as to where the certs might be cached and if I'm using some sort of domain certificate store that's hiding from me.

  Read the article

• KVM and libvirt: How to configure a new disc device to an existing VM?

  - by initall

  I've got an Ubuntu 9.04 server running two VM's. In /etc/libvirt/qemu/machine1.xml two disk devices are defined like this: <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <source file='/vserver/machine1/disk0.qcow2'/> <target dev='hda' bus='ide'/> </disk> <disk type='file' device='disk'> <source file='/vserver/machine1/disk1.qcow2'/> <target dev='hdb' bus='ide'/> </disk> I need more storage space in at least one of the devices and thought about adding a third hdc device by simply adding one with same style as above and re-organising my mount structure (The virtual sizes of the current qcow2 files are unfortunately limited.) My problem is that reloading libvirtd and restarting the VM do not result in a new visible device (checked with fdisk). I'm aware of extending an existing qcow2 file (converting to raw format, cat-ing/adding the new one, using smth. like gparted) - but only as a last resort. Hopefully it's something very simple I'm missing?

  Read the article

• Moving a site from IIs6 to IIS7.5

  - by Sukotto

  I need to move a site off of IIS6 (Win Server 2003) and onto IIS7.5 (Win Server 2008) as soon as possible. Preferably tomorrow. The site itself is a delightful mix of classic asp (vbscript) and one-off asp.net (C#) applications (each asp.net app is in its own virtual dir and has a self-contained web.config). In case it's relevant, this is a sort of research site made up of 40 or 50 unconnected microsites. Each microsite is typically a simple form allowing a user to submit a form, which then runs a Stored Proc on a sqlserver db and displays a chart and/or table of the results. There is very little security to worry about. The database connection info is in a central file (in the case of the classic asp) or app's individual web.config (lots of duplication there) To add a little spice to the exercise... I have no idea how to admin IIS The company no longer employs the sysadmin or the guys who set this thing up. (They're not going to employ me much longer either but my sense of professional pride does not permit me to just walk away from this task). The servers are on mutually firewalled networks and I have to perform a convoluted, multi-step process to copy anything from one to the other. Would someone please point me to a crash-course tutorial for accomplishing the above? I have: a complete copy of the site's filesystem on the new box installed the 3rd party charting tool on the new system a config.xml file from the "all tasks - save configuration to a file" right click menu. There doesn't seem to be a way to import it on the new system however. The newer IIS manager has a completely different UI and I'm totally lost. Please help.

  Read the article

• Sync Local ICS File with Android via Exchange/Outlook

  - by sinDizzy

  At my company we have a 3rd party app which tracks off-hours duty for all of our engineers. The app is not web-enabled and we cannot make any changes to it. It does write a simple text file and I have created an app that translates that to an ICS file. My goal is to have that appear on my calendar on my Android phone. Here is the path I am working on: DutyApp -- TextFile -- ICSFile -- Outlook(exchange) -- Android (via exchange sync) My problems: If I place the ICS file on our FILE server and then in Outlook if I go to the option CalendarOpen CalendarFrom Internet it shows up in Outlook and looks pretty good. After a couple minutes it shows up on my Android phone as well. If I change the original ICS file those changes never display in Outlook and never sync to my Android phone. This seems to be a one shot deal almost like an import. Now if I place the ICS file on our WEB server and then in Outlook if I go to the option CalendarOpen CalendarFrom Internet and use webcal:\ as the address, it shows up in Outlook and also looks pretty good. Any changes I make to the original ICS file display in Outlook. However the entire calendar never shows up in Android. This calendar is a subscription and it seems, although am not sure, that Android doesn't display Exchange subscription calendars. Yes I know it works with Gmail subscription calendars but this is Exchange. So my question is what other options are there? We are behind a firewall so cant link the ICS file to a Gmail account. I can't put the ICS file anywhere else other than our file or web server.

  Read the article

• ATI Firepro v4800 3 monitor support

  - by Jared275

  I have an interesting, yet very frustrating problem. I have two computers, both running win7 32 bit, and both with ATI Firepro V4800 graphics cards. Both are using the DVI port and two DP to DVI adapters to connect 3 monitors. One of them is able to display three desktops, while the other fails at enabling the third, displaying "cannot save changes" in display properties while requiring that one monitor must be disabled when making the change in CCC. I've verified that both computers have the same driver version and that both are using the same DP-DVI adapters. This articles suggests a few things to try, but none of its suggestions seem to work either. I'm kind of at my wits end, hence my posting here. If this is not an appropriate question for SU, I apologize. I admit that I am not very familiar with the differences between dual link and single link DVI, and that is something I have not verified is standardized between the two computers. Is that a possible reason one is working and the other isn't? How do I check if the DVI cable is a single link, or dual link?

  Read the article

• How to repair a corrupted Excel file

  - by SjoerdV

  I'm trying to restore some files for a friend who messed up a USB stick by pulling it out of the computer too soon. By searching invisible partitions I was able to restore the files. All files are intact, except 1 excel file that seems to be corrupted. I've googled about ways to repair an Excel file, because the default repair options in Excel 2003-2010 do not work for this file. I've came across a numerous third-party apps, of which the one seemes to be able to do the job: Recovery Toolbox for Excel. Of-course, this and all other apps I found require a purchase to actually repair the file. It seems a bit silly to pay 30 dollars for a one time thing, and something that is not for myself. So, I would like to keep that as a last-resort option. Is there anything I can try to fix this? I've attached a screenshot of how the file looks when I open it on my OSX when converted to a HTML file (to view the code), for the option that it could be a character set problem.

  Read the article

• How to quickly check if two columns in Excel are equivalent in value?

  - by mindless.panda

  I am interested in taking two columns and getting a quick answer on whether they are equivalent in value or not. Let me show you what I mean: So its trivial to make another column (EQUAL) that does a simple compare for each pair of cells in the two columns. It's also trivial to use conditional formatting on one of the two, checking its value against the other. The problem is both of these methods require scanning the third column or the color of one of the columns. Often I am doing this for columns that are very, very long, and visual verification would take too long and neither do I trust my eyes. I could use a pivot table to summarize the EQUAL column and see if any FALSE entries occur. I could also enable filtering and click on the filter on EQUAL and see what entries are shown. Again, all of these methods are time consuming for what seems to be such a simple computational task. What I'm interested in finding out is if there is a single cell formula that answers the question. I attempted one above in the screenshot, but clearly it doesn't do what I expected, since A10 does not equal B10. Anyone know of one that works or some other method that accomplishes this?

  Read the article

• Recommended Smartphone for Reading PDFs [closed]

  - by mika

  This is as much a software than a hardware question. I use a lot of public transport and perhaps the best way to spend your time there is to read while listening to music. Currently I use Nokia E90 and Adobe Reader LE 2.5 (full version). I was wondering if there are any better alternatives? Requirements: at least 640px wide screen, preferably 800px physical size of the LCD display matters, it should be large, but the phone itself should be as small as possible. This favors touchscreen models PDF reader should be of high quality. It should render most PDFs correctly. Other important features include: full screen mode, keyboard controls for Page Down and page change, multiple zoom levels to adjust to the screen, opening recent documents at the last page read Downsides of E90 + Adobe Reader LE Phone is large compared to the display It is hard to read the display at sunlight Adobe Reader crashes the phone regularly, zoom could have more levels, doesn't remember last page EDIT: Switched to iPhone and GoodReader. Smaller physical screen width compared to E90 is a disimprovement, but other than that I'm happy. GoodReader is the highest quality smartphone PDF reader I've seen so far.

  Read the article

• Partition is missing in /dev

  - by haimg

  I'm having a strange problem since I moved from Centos5 to Centos6. I have three disks, first two are used as a RAID1, and third one is a stand-alone backup disk that is not listed in /etc/fstab (it is mounded when needed and then unmounted). My problem: After a boot, /dev/sdc exists but /dev/sdc1 does not. Also, the links in /dev/disks are also absent for the first partition of sdc. Disk itself is fine, and if I hot-remove it and plug it back in, /dev/sdc1 appears ok and everything is working. My question: What subsystem manages auto-discovery of disks, partitions, etc. during the boot process (e.g. what creates /dev/disks/by-label)? How do I configure it to scan /dev/sdc too and create all relevant files and links in /dev ? Edit: Here's the relevant part of dmesg output (the only place sdc appears). It does list sdc1, but it's not in /dev! sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 3:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdc] Write Protect is off sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdc: sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: DMAR:[DMA Read] Request device [00:1e.0] fault addr 361bc000 DMAR:[fault reason 06] PTE Read access is not set sdb1 sdb2 sdb3 sdc1 sda1 sd 1:0:0:0: [sdb] Attached SCSI disk sd 3:0:0:0: [sdc] Attached SCSI disk sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk

  Read the article

• Todo/task manager for android and desktop linux

  - by RiaD

  I'm looking forward to Task/ToDo Manager. It should work under Android, Linux(or Web). If it's very cool, one of them is OK too, Android is preferable in this situation. Necessary features: Russian or English language Possibility to mark task as finished Interesting features: (I want as more, as possible, while it's OK, if some of them isn't avaliable) Nice and easy-to-use interface Possibility to choose finish time for task. After that it's showed as overdue. Possibility to choose start time for task. Before it task is inactive and maybe shown or hide Possibility to add nested tasks. Task marks completed when all sub-tasks are completed. Possibility to make dependencies. If A depends on B, and B isn't finished yet, A is inactive as in third feature. Possibility to create task in a moment without fill-all-this-forms Syncronization between version(Android to linux or Android to web) Notification (on Android only) Features, that I'm not interested in: Creating more than one todo list sharing ToDo's I've seen couple of managers. Best I've seen now is Task Coach for Linux, but I don't very like its interface, and there is no version for Android.

  Read the article

• Office documents on intranet all requiring second login and can't pass auth? Disable webdav?

  - by DOTang

  I am not sure what is going on, but recently all the Office documents on our intranet get prompted a second time for login and according to the error logs it looks like it's trying to use webdav to open (an editable?) version of the document to save directly on the server? We have no sharepoint server setup or anything, but this shouldn't be happening. All I want is for the document to be saved or opened from a local copy in temp like normal. Here is the log: Line 57499: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57500: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57501: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 The log basically contains a bunch of these. How can I disable this behavior so that office documents that are downloaded aren't attempted to be used through webdav?? Edit: I should clarify behavior, it asks if you want to save or open it, upon choosing open open, it asks to re-authenicate, you put in the user information and the login box comes up 3 times acting like you entered the wrong password. For some users, after passing the login box the third time, it still opens up, for others their browser just locks up. It also doesn't even look like webdav is installed on our server, I see no config options in IIS for it as outlined on this page: http://learn.iis.net/page.aspx/350/installing-and-configuring-webdav-on-iis-7/#001

  Read the article

• How do I change the default ftp folder in MacOS X 10.6?

  - by Wild_Eep

  I'm running WordPress 2.9.1 from a Mac running 10.6.3. WordPress is installed to the /Library/WebServer/Documents folder. WordPress has a feature called AutoUpdate. Clicking an autoupdate button will download and install updated versions of the WordPress software, or third-party plugin tools. It's a convenient way to keep things up to date. WordPress uses FTP to download the files. I've enabled FTP and set up a user account and opened the requisite ports in my firewall for FTP traffic. This doesn't seem to be enough for my self-hosted installation, though. I'm sure this feature was originally designed for someone who has access to a remote shared webserver, and that it's merely a configuration challenge related to the FTP setup. I feel that if I can adjust the initial directory that the FTP service presents to the AutoUpdate feature, everything else will work properly. So, my question is, how do I adjust what folder is presented when a given user connects to a Mac running 10.6.3 via FTP?

  Read the article

• Find whether TV supports S Video

  - by Vik

  Hello Freinds I have a TV (some unknown model) which has 3 sockets to insert 3 wires red, yellow and white. A DVD Player can be connected to the TV using sockets and the TV displays that the TV is in AV mode when DVD is running. Now i have a Desktop which has a S Video Port and i have a wire to connect the S Video port from my computer to those red, yellow and white sockets using appropriate pins. Now i have searched all over the remote and it does not switches to S Video Mode, it has only 2 modes of operation i.e. 1 Cable Connection (Third Party DTH Receiver receives channels and i pay subscription) and 2 AV Mode. It does not have S Video Mode or any other mode. Now my question is whether i can connect the S Video cable from my desktop to the above described TV or i should look for a new TV if i wish to connect the S Video from Computer to TV or there is any sort of converter that can help? I did tried connecting the S Video cable from Desktop to TV, but it did'nt worked. TV kept on displaying Blue Screen of AV Mode. Regards

  Read the article

• Can't install Hyper-V in Windows 8 Pro. Causes boot loop, pain & suffering

  - by Nick

  Hardware: Intel i7 2600K (not overclocked, SLAT compatible, virt. features enabled in bios) Asus Maximus IV Extreme-Z (Z68) 16Gb RAM 256Gb SSD Other non-trivial working parts Adding Hyper-V is causing a boot loop resulting in an attempt at automatic repair by Windows 8 after the second or third loop: I'm trying to get the Windows Phone 8 SDK installed and I've narrowed down my troubles to the Hyper-V feature in Win8. This is required to run the WP8 emulator and there are no install options to omit this feature. My first attempt completely borked the OS as I did not have a recent restore point or system image, so I did a completely clean install and made plenty of backups/restore points. I skipped the SDK install and went straight for the windows feature add-on for Hyper-V. This confirmed that Hyper-V is the issue as the same behavior resulted. I cannot find any hint in the Event Logs. Cancelling automatic recovery causes the same behavior to repeat. I don't have any other VM products installed. My only recourse is to use a restore point, try something else, install it again, and see what happens. No luck so far. I'm on my 10th attempt here. Any help would be much appreciated.

  Read the article

• Vmware player change dhcp server settings

  - by Tathagata

  I have a Windows Server 2003 running from a Vmware player on Win 7 box. The idea is to test Windows Deployment service in the virtual network. Is it possible to configure the vmware dhcp server with WDS related stuff(option 66, 67)? I found a few references where people were using the vnetlib.exe to start, stop the dhcp serverchange the subnet mask etc - but there's no info on how to get set the dhcp server options. DHCP config from the virtual network editor I do have the Workstation, without the license for it. In the Virtual network Editor, the DHCP settings for the network I'm using, only allows me to set the subnetmask, IP ranges and stuff like that. But not the dhcp options. DHCP server on the WDS server Authorizing the DHCP server in the guest WDS server fails. The VMware player can run its own dhcp server fro the virtual network with out any authorization from the Active directory - can I do the same, with Win dhcp server in the guest Win Server? ~~~~~ Can I authorize W2K8 DHCP server for private network, even when prohibited in enterprise network? says we have to run a third party dhcp server... :/.

  Read the article

• Limited connections to Ubuntu 12.04 server

  - by Luis M. Valenzuela

  I'm having a weird problem with my server. The server is inside my network, connected to a 3com switch which is connected to the router that handles the internet connection. The main purpose of the server is to host a php application. What's happening is that user 1 to 15 in the private network have no problems connecting to the server, when user 16 tries to connect a time out comes out and is unable to connect to the server. It's not just to the php application, but to any service from the server. When the 15 users are using the application, the server doesn't even answer to ping. I haven't set any special limit in Apache's ini file or MySql and the firewall is being turned off because the server is only to give service to the internal network. Is there a parameter in any of the network's card conf. files that might me causing this ? Or should I suspect from the router's or switches configuration ? UPDATE. Tomorrow, I'm gonna do some test on the server modifying two kernel params in : /etc/sysctl.conf The settings are: net.core.somaxconn which has the limit on simultaneous network connections to the server and kernel.shmmax which controls the amount of memory the system can use for managing connections.

  Read the article

• How do I repartition an SDHC card in Windows?

  - by Peter Mortensen

  How do I repartition an SDHC card (4 GB or more)? Do I need third-part tools or Linux (a live CD solution would be OK)? In Windows' Disk Management the option Delete Partition is dimmed out: I can reformat the card as FAT32, copy files to and from the card and even change the file system to NTFS using the command line command CONVERT, but not repartition it. The article How to Partition an SD Card in Windows XP talks about using "a Windows enabler program" which sound rather dubious to me. I have tried to change from “Optimize for quick removal” to “Optimize for performance”. The option to format as NTFS appeared, but the Delete Partition option is still dimmed out. Platform: Windows XP 64-bit SD card reader: USB 2.0 device, LogiLink® CR0005C Cardreader 3,5' USB 2.0 intern 54-in-1 mit USB Front Kingston 16 GB SDHC card, speed class 4. (It could be formatted as FAT32 and successfully used in a 4 GB ReadyBoost setup (Windows 7).) I have also tried on different versions of Windows and with different cards with the same result: Kingston 4 GB SDHC card, speed class 4 (the one shown in the screenshot) Transcend 2 GB (not marked as SDHC, but SD) Windows 7 32-bit (albeit with a somewhat an older card reader) and Windows XP 32-bit on an EliteBook 8730w

  Read the article

• Outlook 2007 panes keep moving when changing resolution

  - by SilverbackNet

  This problem is really bugging one of our users ever since he got a larger monitor. Now that the monitor has a different resolution than his laptop, every time he unplugs it to go home, the three Outlook panes get all jumbled up. The navigation is huge, the list is shoved over, and the reading pane is almost smushed out of existence, the the opposite when he comes back in and the reading pane fills the screen. He's sick of adjusting it every day. He always runs it maximized, for maximum reading area. Keeping the application within a 1024x768 window wouldn't really be an option for him. Is there any way built into Outlook to automatically adjust pane sizes when the resolution changes? If not, is there a third-party app that can help, or a way to script the changes into the registry somehow? (I can do running the script whenever the screen state changes.) If this is fixed in 2010 I might be able to convince the other admin that this is a good enough reason to allow it (which will require a new beta version of our archiving software).

  Read the article

• How To Monitor Home Wireless Network Connected Devices Bandwith

  - by GWLlosa

  (Originally posted on SuperUser, not sure if it might be better suited here) I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

< Previous Page | 384 385 386 387 388 389 390 391 392 393 394 395  | Next Page >