Search Results

Search found 24933 results on 998 pages for 'arch linux'.

Page 397/998 | < Previous Page | 393 394 395 396 397 398 399 400 401 402 403 404  | Next Page >

• HELP! Free space not reclaimed after online resizing ext4 in Ubuntu 9.10

  - by TiansHUo

  My root partition was filling up, with only 500 mbs left, I wanted to resize my root partition from 20 Gb to 40Gb So I resized my partition by using these steps: Using Gparted to resize another partition to give space for the EXT4 Using fdisk, deleting the root partition (on /dev/sda2), and creating it again using the new size resize2fs /dev/sda2 Updating grub2 But now the problem is that although I can boot in my new partition and the new partition shows it is 40Gb, but the free size was still 500mb. So I booted from a LiveCD and checked with e2fsck -p /dev/sda2, it reported clean. So I added the -f flag (force check), still, the drive is full.

  Read the article

• Different graphic cards drivers while booting from external media

  - by goran

  I am booting a certain system of mine with ubuntu 9.10 from external HDD. I am satisfied with the setup and it works fine, however I would like to modify it so that I can choose which graphic card drivers to load during the boot time. Specifically I would like to choose between: nvidia proprietary driver ati proprietary driver generic driver Currently if I am using proprietary drivers then dont boot into X, delete xorg.conf, start gdm and reconfigure the system using jockey (for hardware drivers). What would be the steps to make this (semi-)automatic and avoid restarting X?

  Read the article

• Does a successful exit of rsync -acvvv s d guarantee identical directory trees?

  - by user259774

  I have two volumes, one xfs, and another ntfs - ntfs was empty, and xfs had 10 subitems. I needed to sync them. I initially copied a few of the subitems by dragging them over in a gui fm. Several of the direct descendants which i had dragged finished, apparently. One I stopped before it was done, and the rest I cancelled while it still appeared to be gathering information about the files. Then I ran rsync -acvvv xmp/ nmp/, where xmp and nmp are the volumes' respective mountpoints, which exited with a 0 status. find xmp -printf x | wc -c and find nmp -printf x | wc -c both return 372926. My question is: Am I guaranteed that the two drives' contents are identical?

  Read the article

• Problems connecting Centos on VMware to the network using bridged connection.

  - by Sakin

  Hi, I installed CentOs on VMware running on windows XP. When trying to configure it to connect to the internet in a bridged configuration, I get an error message when trying to bring up the network interface: [root@VMLinux ~]# /et/init.d/network start Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... failed [FAILED] VM is running on a machine that has access to the network, I tried it on two different networks that have DHCP enabled. Everything works fine when using a NAT connection through my host. How can I make the bridge work for me? Thanks.

  Read the article

• Set custom mount point and mount options for USB stick

  - by kayahr

  Hello, I have an USB stick which contains private stuff like the SSH key. I want to mount this stick to my own home directory with 0700 permissions. Currently I do this with this line in /etc/fstab: LABEL=KAYSTICK /home/k/.kaystick auto rw,user,noauto,umask=077,fmask=177 0 0 This works great but there is one minor problem: In Nautilus (The Gnome file manager) the mount point ".kaystick" is displayed. I guess Nautilus simply scans the /etc/fstab file and displays everything it finds there. This mount point is pretty useless because it can't be clicked when the device is not present and it can't be clicked when the device is present (Because then it is already mounted). I know this is a really minor problem because I could simply ignore it but I'm a perfectionist and so I want to get rid of this useless mount point in Nautilus. Is there another way to customize the mount point and mount options for a specific USB device? Maybe it can be configured in udev? If yes, how?

  Read the article

• Is there a way to make nautilus display the "recently used" files and directories?

  - by Peltier

  Is there a way to make nautilus display the "recently used" files and directories, just like the "open file" dialog does? Just to make my question clearer, here are two screenshots: The GTK open file dialog, showing the recently used items: A nautilus window, which doesn't offer to display recently used items: EDIT : This has been added as a feature request to Nautilus. Don't hesitate to make your voice heard if you want it to happen!

  Read the article

• High fan speed with no reason

  - by Klaus

  For a few weeks, the fans of my Lenovo B590 laptop, running on Xubuntu 14, turn to high speed a few minutes after it is turned on. The fans won't speed down until I turn the computer off. This is quite strange, since This didn't happen before The temperatures are quite low (are they ?) $sensors Adapter: Virtual device temp1: +36.0°C (crit = +88.0°C) temp2: +30.0°C (crit = +126.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +37.0°C (high = +72.0°C, crit = +90.0°C) Core 0: +34.0°C (high = +72.0°C, crit = +90.0°C) Core 1: +31.0°C (high = +72.0°C, crit = +90.0°C) thinkpad-isa-0000 Adapter: ISA adapter fan1: 0 RPM pkg-temp-0-virtual-0 Adapter: Virtual device temp1: +37.0°C $sudo hddtemp /dev/sda /dev/sda: ST500LT012-9WS142: 33°C The computer is under low load: top - 08:30:15 up 16 min, 2 users, load average: 0.28, 0.23, 0.23 Tasks: 197 total, 1 running, 196 sleeping, 0 stopped, 0 zombie %Cpu(s): 0.8 us, 0.5 sy, 0.0 ni, 98.7 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem: 3607944 total, 1973956 used, 1633988 free, 99660 buffers KiB Swap: 3744764 total, 0 used, 3744764 free. 789936 cached Mem The BIOS is up to date (and there are no fan settings in it) The fan is clean and dust-free Why would the BIOS turn the fans to high speed where there seem to be no reason for that ? It seems that we cannot control the fan manually with this model, so I guess the only solution is to understand why this happens.

  Read the article

• Apache can't get viewed from outside of my LAN

  - by Javier Martinez

  I fixed it in PORTS TRIGGER menu of my router. Thanks you anyway I have a weird problem related with (i think) my cable-router and my configured vhosts in Apache2. The point is I can't access from outside of my LAN to any of my configured vhosts if I set the http port of Apache to 80 and i add a NAT rule for it. Otherwise, if I set my Apache port to 81 (or any else) with its respective NAT rule on my router it works. My router is an ARRIS TG952S and I am using Apache/2.2.22 (Debian) ports.conf NameVirtualHost *:80 Listen 80 vhost1.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost1.mydomain.net ServerAlias vhost1.mydomain.net www.vhost1.mydomain.net vhost2.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost2.mydomain.net ServerAlias vhost2.mydomain.net www.vhost2.mydomain.net DNS records (using FreeDNS) are: mydomain.net --> pointing to another server vhost1.mydomain.net --> pointing to my server vhost2.mydomain.net --> pointing to my server iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination fail2ban-apache-noscript tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-apache tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-ssh tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain fail2ban-apache (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-apache-noscript (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-ssh (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Thanks you

  Read the article

• What did Emolator do with My Laptop?

  - by Garry

  I played SEGA with my KEGA.exe (Sega Emulator) and it made my right key to be malfunctioned. Befor that day, I had played it, too in my notebook with fullscreen mode, and suddenly my ACER Aspire One notebook restarted during that emulator was running and before the screen was black (boot), my screen was blue with many words but I couldn't read them, but I remember that there was a word like 000000 x 0000000 x 000000 and bla bla bla. And when I played without fullscreen mode, It didn't happened but it made my right key to be malfunctioned until when I went to Bot setup, my right key doesn't work. Do U know what is the problem of my emulator? Can U explain me for that?

  Read the article

• iptables and snatting to different networks

  - by codingfreak

  linuxbox (p.q.r.t) | | INTERNAL ------ ABCD ----- INTERNET (p.q.r.s) (m.n.o.k) ABCD has 3 interfaces connected to linuxbox, INTERNAL N/W, INTERNET. Linuxbox has a private address (p.q.r.t). At present I am snatting the packets from linuxbox to INTERNET at ABCD. I have a small doubt regarding the FTP from linuxbox since I have to support ftp from linuxbox to both INTERNAL N/W as well as in INTERNET. How can I right a rule in iptables present in ABCD where it can decide if the destination ip-address of ftp server is within INTERNAL N/W or in INTERNET and do natting accordingly.

  Read the article

• Explaining Git to someone new to revision control

  - by MaxMackie

  I've recently decided to jump into the whole world of revision control to work on some open source projects I have. I looked around (subversion, mercurial, git, etc) and found that Git seemed to make more sense conceptually to me. I've set everything up on my computer (opensuse) and made an account on gitorious (let me know if there is a more simple/better hosting provider). I understand Git from a conceptual point of view (work locally, commit to a local repo, others can now checkout from you, right?). But where does gitorious come into play? I commit to them as well as committing locally? Apart from conceptually, I don't quite understand HOW it works when it comes to making a local repository and running git init inside a folder and that HEAD file. Keep in mind I have never used any form of revision control ever before. So even the most basic concepts are foreign to me. As I post this, I'm also reading up and trying to figure it out myself.

  Read the article

• how do I set up a virtual host (it's not working, and I've done everything right)

  - by piratepartypumpkin

  My router redirects port 80 to port 8080. My router works fine and my domain name is routed properly. This is my virtual hosts file: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /home/admins/lampstack-5.3.16-0/apps/wordpress ServerName example.com ServerAlias www.example.com </VirtualHost> I can access my website by entering "mywebsite.com:8080" but I cannot access it by entering "mywebsite.com" For further information, this is a part of my httpd.conf: Listen 8080 Servername localhost:8080 DocumentRoot "/home/admins/lampstack-5.3.16-0/apache2/htdocs <Directory /> Options FollowSymLinks AllowOverride None Order deny, allow deny from all </Directory> <Directory "/home/admins/lampstack-5.3.16-0/apache2/htdocs"> Options FollowSymLinks AllowOverride None Order allow, deny allow from all </Directory>

  Read the article

• Wi-Fi Stick with ZD1211 chip refuses to work on Ubuntu >8.10. No clue.

  - by Benjamin Maus

  I have a machine running Ubuntu 9.10 (Karmic *x86_64*). Everything is running smooth so far, except for the Wi-Fi USB Stick. The same device worked perfectly in 8.10. The wireless device is a GW-US54GXS using the Zydas Zd1211 chipset. Dmesg output after plugging in: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' [ 196.304209] zd1211rw 2-1:1.0: phy0 [ 196.304227] usbcore: registered new interface driver zd1211rw [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Syslog output: Nov 5 11:20:24 somesystem kernel: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' Nov 5 11:20:24 kierkegaard NetworkManager: <info> Found radio killswitch rfkill0 (at /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/ieee80211/phy0/rfkill0) (driver <unknown>) Nov 5 11:20:24 somesystem kernel: [ 196.304209] zd1211rw 2-1:1.0: phy0 Nov 5 11:20:24 somesystem kernel: [ 196.304227] usbcore: registered new interface driver zd1211rw Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): new 802.11 WiFi device (driver: 'zd1211rw') Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/2 Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): now managed Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): device state change: 1 -> 2 (reason 2) Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): bringing up device. Nov 5 11:20:24 somesystem kernel: [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:24 somesystem kernel: [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 Nov 5 11:20:24 somesystem kernel: [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- Nov 5 11:20:24 somesystem NetworkManager: <WARN> nm_device_hw_bring_up(): (wlan0): device not up after timeout! Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): deactivating device (reason: 2). Nov 5 11:20:24 somesystem kernel: [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:29 somesystem wpa_supplicant[978]: Could not set interface 'wlan0' UP Nov 5 11:20:29 somesystem wpa_supplicant[978]: Failed to initialize driver interface Nov 5 11:20:29 somesystem NetworkManager: <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. Gnome tells me in the network menu that the device was "not ready". It appears in iwconfig but not in ifconfig. The same symptoms appear when I boot from the live CD. How can I solve this dilemma?

  Read the article

• Accessing a guest OS's directory from the host OS in VirtualBox

  - by hekevintran

  With VirtualBox you can share a directory on the host machine with the guest machine. Can you share a directory on the guest machine with the host machine? In my setup the host is Windows 7 and the guest is Ubuntu. Can I have a directory on the Ubuntu file system accesible from Windows?

  Read the article

• problem with zsh interactive shell

  - by Jack

  When I use zsh in interactive mode, I get some glitches. This mainly happens when the command spills over onto a new line and I use backspace, with backspace leaving behind some glitches on the screen and moving the cursor to an odd position. It happens in a VT, in xterm and urxvt, although it is most noticeable with my chosen terminal, urxvt. When I use zsh as a login shell, it does not happen at all. What could be causing this?

  Read the article

• Why does my Mac address reset after reconnecting?

  - by Mr.Student

  I have ubuntu 12. I'm changing my mac address with ifconfig wlan0 hw ether xx:xx:xx:xx:xx:xx which works. However when I restart my connection my computer resets my mac to my original mac address. I'm guessing that this happens because something calls... ifconfig wlan0 down ... do something before connecting ifconfig wlan0 up ... connect to designated access point I want my mac address to however be the same no matter how many times I disconnect and reconnect, whether to another network or the same one. Also it would be nice to turn off the auto-connect feature for my network-manager with out having to edit each individual connection. Lastly I would like to know how to connect to a wifi network through the terminal and not via gui network manager ubuntu provides.

  Read the article

• Why does sshd give a different identification when connecting through netcat?

  - by Robbie Mckennie

  I have been attempting to create a way to ssh into a machine hiding behind a firewall. I set up my ssh client with the option Proxycommand /usr/bin/ncat -l 2000, and then I connect it to sshd with ncat <client> 2000 -c "sshd -i" on the server. It works in that I can get a shell on the server, but the server sends a different key than when I use normal ssh. So the question is, why? Is the key different when sshd is called in this unusual way?

  Read the article

• Does anyone know why rsync would keep sending the files over and over again?

  - by beagleguy

  I'm trying to using rsync to backup some files, about half a TB. It's now it a state where it keeps sending the same files everytime it runs. for example: rsync -av /data/source/* user@host:/data/dest sending incremental file list source/file1.txt source/file2.txt I then verify those files are copied over... then the next time it runs it does the same thing rsync -av /data/source/* user@host:/data/dest sending incremental file list source/file1.txt source/file2.txt any idea why it's getting stuck on these files? I've tried to wipe the whole dest directory out and start over but no luck. thanks,

  Read the article

• Primary/secondary ethernet interfaces via NetworkManager in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local... EDIT: Here's my routing table: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.151.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 172.16.30.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.1.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 172.16.30.2 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.0.1 0.0.0.0 UG 0 0 0 eth1 I want the 172.16.30.2 network to be the primary one and the 10.1.0.0 network to be the secondary one. EDIT2: My nameservers are also incorrect. It seems like Ubuntu is bringing the networks up in order, eth0, then 1, then 2, and the DHCP information from eth1 is overriding eth0, and eth2 is overriding eth1. How can I reverse this so the DHCP information from eth0 is the "master"? EDIT3: This seems to be an issue with Gnome's NetworkManager.

  Read the article

• How can I get the ./configure options used to build Apache?

  - by Josh

  I am using CentOS, and would like to build from source with the newer version of apache using the same configure options as the package obtained using yum, with an adjustment or two. How would I go about acquiring that?

  Read the article

• Not able to connect to internet in RHEL 5

  - by chankey007

  I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

  Read the article

• Not able to connect to internet in RHEL 5

  - by chankey007

  I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

  Read the article

• Cron ignoring an update to crontab

  - by GJ

  I've commented out a line in the crontab on a debian server, which I guess was there by default yet was causing me to get error emails every hour: # m h dom mon dow user command 17 * * * * root cd / && run-parts --report /etc/cron.hourly However, the error emails keep coming in as if it hasn't been commented out. The error emails: Subject: Cron <root@(none)> root cd / && run-parts --report /etc/cron.hourly (failed) /bin/sh: root: not found Any ideas?

  Read the article

• Conditionnal relay in postfix

  - by Florent

  I use postfix to send direct email. But, I use a relay to send email for specific senders. So I use "sender_dependent_relayhost_maps" : /etc/postfix/main.cf : relayhost = transport_maps = hash:/etc/postfix/transport smtp_sender_dependent_authentication = yes sender_dependent_relayhost_maps = hash:/etc/postfix/sender_relay /etc/postfix/sender_relay : [email protected] smtp.relay.com So when I send an email with sender email "[email protected]", postfix will use the relay. But... I don't want to use the relay host for some recipient. ;) I think I must use "transport_map" to catch the email before it pass through "sender_dependent_relayhost_maps" but I don't know how to do it... Thanks

  Read the article

• How to have a soft-real-time process in presense of heavily swapping IO-intensive background load?

  - by Vi

  schedtool: PID 32301: PRIO 4, POLICY R: SCHED_RR , NICE -20, AFFINITY 0xf ionice: realtime: prio 4 But the music is stumbling anyway. Background load is low prio (SCHED_IDLEPRIO, idle ionice), but uses a lot of memory (more than is physically available) and does a lot of IO and calculations. Latencytop shows about 1500ms for: Following symlink Writing buffer to disk (sync) Page fault Writing a page to disk both for the bg load and for unrelated processes. Load average is 10 and counting. Why cannot it allocate, for example, 200MHZ of one of the cores and 32M of memory and not less than once per second opportunity for IO for mplayer to make it happy while continuing calculations on the background? Or: why it cannot leave background task and swap loving each other but keeping the rest of the system as if there were no background load? How to have RT processes AND heavy bg load simultaneously (without of virtual machines)?

  Read the article

< Previous Page | 393 394 395 396 397 398 399 400 401 402 403 404  | Next Page >