Search Results

Search found 12726 results on 510 pages for 'compatibility mode'.

Page 408/510 | < Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >

• ubuntu 9.10 installer doesn't recognize the hard drive

  - by dan

  I downloaded Ubuntu 9.10 x86_64 and am trying to install it on a fairly modern system with a Gigabyte GA-MA770-UD3 motherboard. Ubuntu 9.04 installed fine and still will when I stick that disc in, but 9.10 doesn't see my hard drive (western digital 250GB). If I boot from the disc, I can install gparted and it does recognize the drive, but when I try to start the install process from the live disc, Ubuntu again doesn't recognize the hard drive. I checked /var/log/messages and see this: Nov 12 17:28:08 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was bad, boot with 'nodmraid'. Nov 12 17:28:08 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: no raid sets and with names: "nvidia_ciiajheb-0" Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. I checked my BIOS, SATA is enabled and is set to IDE mode, so there shouldn't be software RAID, but nonetheless, I added nodmraid to the boot line and tried again. It still doesn't recognize the drive. I checked /var/log/messages again and now see this: Nov 12 17:49:38 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was boad, boot with 'nodmraid'. Nov 12 17:49:38 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Any ideas on things to try? I've tried all of the various BIOS settings for SATA. IDE,RAID, etc. Nothing seems to work.

  Read the article

• how to remove background layer of djvu file

  - by Jon

  Hello, I've downloaded some files from the Internet Archive. They come in different file formats and most of the time I use pdf. However, sometimes the scans are saves in colour instead of b/w. This makes it difficult/impossible to read on a dedicated ebook reader. In that case I downloaded the djvu files as on the PC you can select which layer (color, bw,fore,back) one would like to see. Selecting the bw gives excellent results. However, the ebook reader does not has this option. The question is, how can I remove /extract a layer from the djvu file and save only this layer. So far I've tried the following two approaches: 1) select bw in the djvu viewer on the PC and printed to postscript file. Followed by a ps2pdf conversion. This works, but generates a fairly large pdf file. Sure, I can again upload it to any2djvu but it just seems to much manual work for each file. 2) I tried the shared annotation feature and said (mode bw). This works on the PC as desired but is ignored on the ebook reader as the other layers are still present. Any help or suggestions would be greatly appreciated.

  Read the article

• Win 8.1 Hyper-v Full Screen and VPN problems

  - by tr0users

  I need to connect to my office using Cisco VPN software (RSA). Once connected all my internet traffic goes through the employer's VPN and this prevents me from listening to spotify. As a way around this I created a Win 2012 VM that I run in hyper-v from my Windows 8.1 Client. First I RDP to the VM, then I connect to the VPN. This forces the RDP session between my host laptop and the VM to close. I then open the hyper-v manager and double-click my VM to get a connection back (not great because I don't get the use of copy & paste this way). Previously when I opened my VM this way I would have full screen. I'm using a 1920x1080 monitor. Today when I re-open my connection to the VM it is displayed in a window that uses maybe 75% of the full screen. I have tried the menu option View\Full Screen Mode only centres the screen and apply black borders around the outside. Could anyone please suggest how I may solve the VPN or Full Screen problems? Thanks Rob.

  Read the article

• How to autorun wpa_supplicant on Debian startup

  - by The Electric Muffin

  I'd like to run wpa_supplicant -D wext -i wlan0 -c /etc/wpa_supplicant.conf on Debian startup (runlevels 2-5). I found some vague instructions from a related question that said to put a script in /etc/init.d/ and then symlink to it from the apropriate /etc/rcRUNLEVEL.d/ directories. However, I noticed that there are already some files named "wpasupplicant" that probably run at startup: /etc/network/if-down.d/wpasupplicant /etc/network/if-post-down.d/wpasupplicant /etc/network/if-pre-up.d/wpasupplicant /etc/network/if-up.d/wpasupplicant They all are symlinks to the same script, /etc/wpa_supplicant/ifupdown.sh. It has a comment at the beginning saying it "[...] allows ifup(8), and ifdown(8) to manage wpa_supplicant(8) and wpa_cli(8) processes running in daemon mode." However, the closest it gets to calling wpa_supplicant itself is (in functions.sh): WPA_SUP_BIN="/sbin/wpa_supplicant" [snip] start-stop-daemon --start --oknodo $DAEMON_VERBOSITY \ --name $WPA_SUP_PNAME --startas $WPA_SUP_BIN --pidfile $WPA_SUP_PIDFILE \ -- $WPA_SUP_OPTIONS $WPA_SUP_CONF [snip] start-stop-daemon --stop --oknodo $DAEMON_VERBOSITY \ --exec $WPA_SUP_BIN --pidfile $WPA_SUP_PIDFILE Does that mean it's safe to make an init.d script for wpa_supplicant, and if so what would it look like? General info: Debian Squeeze (5.0) official wpasupplicant package (v0.6.10-2.1) The full contents of my system's functions.sh and ifupdown.sh are here (dependent, of course, on my system's uptime—it's a five-year-old laptop that greatly enjoys overheating): functions.sh ifupdown.sh

  Read the article

• Why can't I use my Bluetooth Headset with my laptop?

  - by Michael Haren

  I just received a new Plantronics M50 bluetooth headset. It works great with my phone, but I can't get it working with my laptop. What are the things I should be checking? Here's what I've done so far: It pairs successfully: It's not in multipoint mode--it's only paired to my laptop I've installed all available drivers from Plantronics and Dell I have no (!) in Device Manager (though I don't see the headset there either--would I?) I can "configure" the headset by double clicking on it: "Allow the computer to turn off this device to save power" is unchecked in the Bluetooth radio settings Apps that let me choose the playback/mic device only list my laptop, not the headset [UPDATE] I went into the Bluetooth device's properties and Checked "headset" under the services tab. This was successful but hasn't delivered any functionality as far as I can tell I'd like to use this headset for VOIP conferencing (Goto meeting, Gmail voice chat, G+ hangouts, Skype, etc.) and listening to music (iTunes). Where else should I be digging? Is it possible that this new headset is simply not compatible with computers (i.e. it's only compatible with phones)?

  Read the article

• How to define nodes from a Hiera file in Puppet?

  - by Pigueiras

  I am using puppet and the puppet network device management module and I am trying to build my custom type. In the built-in type for the routers configuration, you can specify a list of nodes and then the configuration inside that node: node "c2950.domain.com" { Interface { duplex => auto, speed => auto } interface { "FastEthernet 0/1": description => "--> to end-user workstation", mode => access, native_vlan => 1000 # [...] More configuration } What I am trying to do, is to move the manifest declaration of the nodes and the configuration of my custom type to a Hiera file like this one: nodes: - node1 - node2 config_device: node1: custom_parameter: "whatever1" node2: custom_parameter: "whatever2" And then in the manifest iterate over the hiera file creating the nodes with the configuration of each node with something like (I am taking as reference this question in serverfault): class my_class { $nodes = hiera_array('nodes') define hash_extract() { $conf_hash = hiera_hash("config_device") $custom_paramter = $conf_hash[$name] ## TRICK lies in $name variable node $name { my_custom_device { $name: custom_parameter => $device_conf['custom_parameter'] } } } hash_extract{$pdu_names: } } } But for this solution I have two problems, I can not define a node inside a define and I can not parameterize a node name. So, is there any way to declare nodes from a Hiera file with their configuration inside?

  Read the article

• Task scheduled to wake laptop - only works when lid is open

  - by JD Pack

  I am running Windows 7 Starter on an Acer Aspire One laptop. I want my laptop to automatically run a task (backup the HDD to a network drive) once a week in the middle of the night. I scheduled the task in "Task Scheduler" and checked the box to wake the computer to run the task. I also changed the advanced power settings to allow wake timers. This was half of the solution. It now works flawlessly when the lid is open... the computer can wake itself up from either sleep or hibernate mode to perform the backup. When the lid is closed however, its sleeping beauty. Any ideas? I don't want to have to remember to open the lid once a week. It sort of defeats the purpose of an "automatic" backup. Update: I discovered that it can wake from sleep (or hybrid sleep), but not from hibernate when the lid is closed. This is good news. I'd still be curious about how to get it to work from hibernate, but I'm pretty happy about waking from sleep at least.

  Read the article

• Setting Remote Desktop to allows IPv6 connections

  - by Garrett

  Setup: Basically I have 3 machines (2 virtual and 1 physical) that I would like to be able to RDP in to from outside my NAT (a router). The VMs are Windows 7 and Windows XP, both fully patched with Teredo installed and working, both running in VirtualBox (their host also has Teredo working, though I'm not sure if that matters). They both have bridged network adapters with promiscuous mode enabled. The physical machine is Windows 7 fully patched with an HFS server running on it and a dynamic DNS set up for my public IPv4 address and port forwarded. It also has Teredo installed and working. Symptoms: According to http://test-ipv6.com/ all 3 have public IPv6 addresses, and they can all connect to http://ipv6.google.com/. I can ping the XP VM from the host it's running on but I cannot ping it from any other machine. Also, I cannot ping either of the other machines from anywhere. I cannot connect to any of them over RDP from IPv6, however I can connect to all of them through IPv4. Any ideas what is going wrong?

  Read the article

• NAT via iptables and virtual interface

  - by Alex

  I'm trying to implement the following scenario: One VM-host, multiple guest VMs, each one gets its own IP-address (and domain). Our server has only one physical interface, so the intended use is to add virtual interfaces on eth0. To complicate our situation the provider uses port-security on their switches, so I can't run the guest interfaces in bridged mode, because then the switch detects a "spoofed" MAC-address and kills the interface (permanently, forcing me to call the support, which I'm sure will get them a little bit angry the third time ;) ). My first guess was to use iptables and NAT to forward all packages from one virtual interface to another one, but iptables doesn't seem to like virtual interfaces (at least I can't get it to work properly). So my second guess is to use the source IP of the packages to the public interface. Let's assume libvirt creates a virbr0-network with 192.168.100.0/24 and the guest uses 192.168.100.2 as IP-address. This is what I tried to use: iptables -t nat -I PREROUTING --src public_ip_on_eth0:0 -p tcp --dport 80 -j DNAT --to-destination 192.168.100.2:80 That doesn't give me the intended results either (accessing the server times out). Is there a way to do what I'm trying to do, or even to route all traffic to a certain IP on a virtual interface to the VM's device?

  Read the article

• All of the NTFS hard links disappear, where are hardlinks stored on disk and how to recover them?

  - by Osiris

  This is Windows 7 x64 sp1 on a NTFS file system. All hardlinks within C:\Windows\System32 folder disappear, and the Windows can't boot, because even the osloader, C:\Windows\System32\boot\Winload.exe also disappeared. Nevertheless, the original files are still located in the corresponding C:\Windows\winsxs folders. After booting into the Recovery Environment, and copied one Winload.exe (x64) from other folder, Windows gave an error pointing out that "ntoskrnl.exe is corrupted or missing...its file digital signature cannot be verified" In trying to boot in Safe Mode, the message above was shown after a screen prompting "Loaded \Windows\system32\config\system" Because at this early booting stage, smss.exe was still not loaded, so there is not any dumping and logs. Based on my study, ntoskrnl.exe depends on the following files: C:\\windows\\system32\\PSHED.DLL C:\\Windows\\System32\\hal.dll C:\\Windows\\System32\\kdcom.dll C:\\Windows\\System32\\clfs.sys C:\\Windows\\System32\\ci.dll All those files above are copied from their corresponding folders and verified their md5 with a well-operating Windows 7 x64 SP1. But the booting error is still the same: "ntoskrnl.exe is corrupted or missing..." **Background:** Before the reboot, there was an windows update going on. Then something unknown happen, almost all processes were broken to run, including the windows task manager, taskmgr.exe. After mount the hard disk to other computer, it seems that all hardlinks within C:\Windows\System32 folder were gone. I tried several data recovery software, but they are not be able to find those disappeared NTFS hard links. So the question is: Where are information about those hard links stored? And how to recover them? Are they depend on some windows service or stored in the registry?

  Read the article

• Use external display from boot on Samsung laptop

  - by OhMrBigshot

  I have a Samsung RV511 laptop, and recently my screen broke. I connected an external screen and it works fine, but only after Windows starts. I want to be able to use the external screen right from boot, in order to set the BIOS to boot from DVD, and to then install a different OS and also format the hard drive. Right now I can only use the screen when Windows loads. What I've tried: I've tried opening up the laptop and disconnecting the display to make it only find the external and use the VGA as default -- didn't work. I've tried using the Fn+key combo in BIOS to connect external display - nothing I've been looking around for ways to change boot sequence without entering BIOS, but it doesn't look like it's possible. Possible solutions? A way to change boot sequence without entering BIOS? Someone with the same brand/similar model to help me blindly keystroke the correct arrows/F5/F6 buttons while in BIOS mode to change boot sequence? A way to force the external display to work from boot, through modifying the internal connections (I have no problem taking the laptop apart if needed, please no soldering though), through BIOS or program? Also, if I change boot sequence without accessing external screen, would the Ubuntu 12.1 installation sequence attempt to use the external screen or would I only be able to use it after Linux is installed and running? I'd really appreciate help, I can't afford to fix the screen for a few months from now, and I'd really like to make my computer come back to decent performance! Thanks in advance!

  Read the article

• Google Drive terminates without error on startup

  - by Iszi

  I've used Google Drive for awhile now, but it won't start up after installing on my latest system re-build. I'm still using the same OS, hardware, and basic software load (antivirus, firewall, etc.) that I have for years during which I had not previously had problems with Drive. OS: Windows 7 Ultimate x64 Google Drive Version: 1.12.5329.1887 Now, whenever I try to run Google Drive, it just spawns two instances of the executable which die shortly after. No error messages are posted to the desktop, and nothing indicating any problem is written to the Event Log. After some research, I've yet to find anyone having the same problem who's found an answer. I did find out how to run Google Drive in diagnostic mode, using the --vv parameter at the command line. After that, I opened up the sync log and got this: 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 OS: Windows/6.1.7601-SP1 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 Google Drive (build 1.12.5329.1887) 2013-10-31 17:11:24,039 DEBUG pid=3664 1892:MainThread logging:1608 DEBUGGING DUMP is ON. 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 ERROR, UNEXPECTED EXCEPTION 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 [Error 5] Access is denied Traceback (most recent call last): File "<string>", line 232, in Main File "<string>", line 118, in RegisterCustomFileTypes File "P:\p\agents\hpal4.eem\recipes\353983091\base\b\drb\googleclient\apps\webdrive_sync\windows\build\pyi.win32\main\outPYZ1.pyz/windows.registry", line 62, in GetValue WindowsError: [Error 5] Access is denied 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Crash reporting disabled. Ignoring report. 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Exiting with error code: 0 I'm running on an account with Administrator-level permissions, and have even tried using "Run As Administrator" on the EXE. I'm not sure why it's looking for a P:\ drive, as no such volume has ever been mounted on this system. What should I do to try to further troubleshoot, and resolve, this issue?

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: How do I remove the option to eject SATA drives from the Windows 7 tray icon?

  Read the article

• SQL Server Subscriber Migration

  - by SuperCoolMoss

  We're currently have one way transaction replication from a SQL Server 2005 OLTP publisher/distrbituor to two subscribers (one SQL 2005 and the other SQL2008 R2). Replication security is via the SQL Agents' domain service account (the same account is used on all boxes). The SQL2008R2 subscriber is used for BI purposes and hosts a database that has a subset of the Production publisher database tables, with different security and indexes. We need to migrate this BI subscriber to a newer box with more performant hardware. The plan is as follows: Stop replicating to the BI box (continue replicating to the other subscriber). Backup all databases on the BI box (including system databases). Restore all databases (including master in single user mode) to the new BI box (this has SQL Server 2008R2 already installed). Take the old BI box off the network and shut it down. Rename and Re-IP the new BI box to be the same as the old box. Switch replication back on. Are there any flaws in this approach?

  Read the article

• Varnish does not start properly (crashes after startup) with no error messages

  - by Matthew Savage

  I am running Varnish (2.0.4 from the Ubuntu unstable apt repository, though I have also used the standard repository) in a test environment (Virtual Machines) on Ubuntu 9.10, soon to be 10.04. When I have a working configuration and the server starts successfully it seems like everything is fine, however if, for whatever reason, I stop and then restart the varnish daemon it doesn't always startup properly, and there are no errors going into syslog or messages to indicate what might be wrong. If I run varnish in debug mode (-d) and issue start when prompted then 7 times out of time it will run, but occasionally it will just shut down 'silently'. My startup command is (the $1 allows for me to pass -d to the script this lives in): varnishd -a :80 $1 \ -T 127.0.0.1:6082 \ -s malloc,1GB \ -f /home/deploy/mysite.vcl \ -u deploy \ -g deploy \ -p obj_workspace=4096 \ -p sess_workspace=262144 \ -p listen_depth=2048 \ -p overflow_max=2000 \ -p ping_interval=2 \ -p log_hashstring=off \ -h classic,5000009 \ -p thread_pool_max=1000 \ -p lru_interval=60 \ -p esi_syntax=0x00000003 \ -p sess_timeout=10 \ -p thread_pools=1 \ -p thread_pool_min=100 \ -p shm_workspace=32768 \ -p thread_pool_add_delay=1 and the VCL looks like this: # nginx/passenger server, HTTP:81 backend default { .host = "127.0.0.1"; .port = "81"; } sub vcl_recv { # Don't cache the /useradmin or /admin path if (req.url ~ "^/(useradmin|admin|session|sessions|login|members|logout|forgot_password)") { pipe; } # If cache is 'regenerating' then allow for old cache to be served set req.grace = 2m; # Forward to cache lookup lookup; } # This should be obvious sub vcl_hit { deliver; } sub vcl_fetch { # See link #16, allow for old cache serving set obj.grace = 2m; if (req.url ~ "\.(png|gif|jpg|swf|css|js)$") { deliver; } remove obj.http.Set-Cookie; remove obj.http.Etag; set obj.http.Cache-Control = "no-cache"; set obj.ttl = 7d; deliver; } Any suggestions would be greatly appreciated, this is driving me absolutely crazy, especially because its such an inconsistent behaviour.

  Read the article

• How to stop Firefox on an SSD from freezing when using the search box or submitting a form?

  - by sblair

  Firefox usually freezes for about a second whenever I search for something from the toolbar search box, when submitting a form, or when clearing the search box history. I suspect it has something to do with the auto-complete feature. Using Windows 7's Resource Monitor, the problem seems to be from the file: C:\Users\<username>\AppData\Roaming\Mozilla\Firefox\Profiles\<profile>\formhistory.sqlite-journal I believe this is a temporary file which caches database writes. The following screenshot shows the very high response times from six different searches, and that the queue length on drive C shoots off the scale: My Firefox profile is on an Intel X25-M G2 SSD. The problem doesn't seem to occur if I create a new profile on a hard disk drive. However, I'd like to know why the problem exists on the SSD in the first place (because it's an annoying problem which contradicts the reason I bought an SSD, and it might happen with other applications too), and how to prevent it. It still occurs if Firefox is started in safe mode, and with the recent beta versions. Updates: VACUUMing the Firefox profile databases does not help with this problem. The SSD Optimizer in the Intel SSD Toolbox does not help either.

  Read the article

• Windows Update and lsass.exe

  - by David

  I have a brand new installation of Windows XP (SP1 or older). I installed Norton AntiVirus, Firefox, Putty, and Cygwin. No other software is present. Windows Update finds the following 64 updates: KB905760, KB978262, Internet Explorer 8, KB71961, KB954155, KB968816, KB923561, KB950762, KB949402, KB950974, KB951376, KB951748, KB952004, KB952954, KB955069, KB956572, KB956802, KB956803, KB956844, KB958470, KB958869, KB959426, KB960803, KB960859, KB961501, KB969059, KB970238, KB970238, KB971032, KB971468, KB971657, KB972270, KB973507, KB973815, KB973904, KB974112, KB974318, KB974392, KB975025, KB975560, KB975561, KB975713, .......) When these updates are applied, the system reboots to a black screen with two error messages. The first error message says: lsass.exe - Application Error The application failed to initialize properly (0xc00000142). Click on OK to terminate the application. The second error message says: services.exe - Application Error The application failed to initialize properly (0xc00000142). Click on OK to terminate the application. I then proceed to boot into Safe Mode, use System Restore, and everything works fine again until the 64 updates re-appear in Windows Update. I can see two options: disable Auto-Updates or install each of the 64 updates one at a time until finding the troublesome update. Does anyone have any better ideas?

  Read the article

• pfsense 2.0 traffic priority - set full priority for single host

  - by Waxhead

  I have a network with several computers all on the same network and since I have very limited bandwidth I would like to prioritize traffic almost like a CPU scheduler prioritize processes. Example: Computer A: Used for webstuff: YouTube, downloads, news, emails etc. Computer B: Transferring files over HTTP Computer C: Transferring files over ftp, rsync whatever What I would like to do is to give A up to for example 90% of the available bandwidth IF A requires it. The leftovers (10%) is divided between B and C (5% each if both is busy) If A is not utilizing all bandwidth then of course B and C should share the full bandwidth (50% each as long as both are maxing out their bandwidth). All computers are on the same network (192.168.1.0 - 192.168.1-10 for example). Appreciate if anyone could shed some light on how I should set up my network to achieve this. To be honest I actually need a step by step guide on how I should set this up. Network setup: (ADSL modem configured in bridge mode (1500kbps/300kbps)) [ADSL modem (bridge)]<-[pfsense2.0]<-[switch]<-[Computer A,B,C...etc]

  Read the article

• Is there a utility to visualise / isolate and watch application calls

  - by MyStream

  Note: I'm not sure what to search for so guidance on that may be just as valuable as an answer. I'm looking for a way to visually compare activity of two applications (in this case a webserver with php communicating with the system or mysql or network devices, etc) such that I can compare the performance at a glance. I know there are tools to generate data dumps from benchmarks for apache and some available for php for tracing that you can dump and analyse but what I'm looking for is something that can report performance metrics visually from data on calls (what called what, how long did it take, how much memory did it consume, how can that be represented visually in a call stack) and present it graphically as if it were a topology or layered visual with different elements of system calls occupying different layers. A typical visual may consist of (e.g. using swim diagrams as just one analogy): Network (details here relevant to network diagnostics) | ^ back out v | Linux (details here related to firewall/routing diagnostics) ^ back to network | | V ^ back to system Apache (details here related to web request) | | ^ response to V | apache PHP (etc) PHP---------->other accesses to php files/resources----- | ^ v | MySQL (total time) MySQL | ^ V | Each call listed + time + tables hit/record returned My aim would be to be able to 'inspect' a request/range of requests over a period of time to see what constituted the activity at that point in time and trace it from beginning to end as a diagnostic tool. Is there any such work in this direction? I realise it would be intensive on the server, but the intention is to benchmark and analyse processes against each other for both educational and professional reasons and a visual aid is a great eye-opener compared to raw statistics or dozens of discrete activity vs time graphs. It's hard to show the full cycle. Any pointers welcome. Thanks! FROM COMMENTS: > XHProf in conjunction with other programs such as Perconna toolkit > (percona.com/doc/percona-toolkit/2.0/pt-pmp.html) for mySQL run apache > with httpd -X & (Single threaded debug mode and background) then > attach with strace -> kcache grind

  Read the article

• Windows 7 Update freezes - what to do?

  - by Tom Tom

  Hi, Yesterday I shutdown my notebook, and Windows 7 Ultimate started to install automatic updates. After one hour, I noticed that the update was still running. I thought OK, I shall go to sleep and let it run. In the morning it was still running. Thus, I thought it had crashed, forced a shutdown of the notebook and then restarted it. With the same effect that the notebook is "freezing" at "Install Update 1 of 5". It does not look like it has crashed. The progress wheel is still moving. But it does not make any progress... Would appreciate any help! Edit: OK, I was able to log-in into safe mode. This way I passed the install update screen. I do not want to generally disable updates, what can I do to not install the last update, which is creating troube. Or how can I find out whats the problem with the last update?

  Read the article

• Sparc Solaris 2.6 will not boot

  - by joshxdr

  I have a very old Sparc Solaris network that was working fine last week, but after a power outage none of the workstations will boot. The network looks like this: host A: solaris 2.6, shares /export/home to network by NFS host B: solaris 8, runs NIS server. Mounts /export/home/ by NFS. host C: RHEL5, shares /share to network by NFS. Mounts /export/home/ by NFS. I figured that the main problem was host A, since you need the home directories available for the other workstations to boot(?). Host A does not mount anything by NFS as far as I know. However, this workstation will NOT boot. The OBP bootup sequence looks like this: Boot device <blah> configuring network interface le0 Hostname <hostname> check file system <everything ok> check ufs filesystem <everything ok> NIS domainname is <name> starting router discovery starting rpc services: rpcbind keyserv ypbind done setting default interface for multicast: add net 224.0.0.0: gateway <hostname> <HANGS at this point> Is there some kind of debug mode so that I can get more detail as to why the workstation won't boot? Is my network structure inherently susceptible to power outage? Is there a way I can boot up to command line so I can at least turn off the NFS mounting?

  Read the article

• Help trying to figure out why IIS7 is crashing / locking up / denying connections

  - by Pure.Krome

  Hi folks, I've got a pretty busy website that is running on a single web front end machine, on W2K8 + IIS7. Every now and then - eg. maybe monday at 3am or something, then a few days later .. some early morning time .. then nothing for 2 weeks ... etc - the website fails to respond to any client connections. ie. no one can connect to the website. I can remote desktop to the machine, etc no probs. I restart the app pool (the website is running in intergrated mode), still nothing. I try and get a crash dump of the process (it's around 600 mb maybe even more) ... that fails after about a min of trying (and i have plenty of HD space). The only way to fix this issue, is to manually stop the www service and then start it again. The stopping takes a while (a minute?) while starting is nearly instant. I'm at a loss to figure out what part of my code is causing this. At first, I thought it might be a stack overflow because of some error that might be going to the error page, which in turn errors .. rinse repeat boom. But i've had a look at the error page and it feels ok. So, I'm hoping someone might be able to help and say how I can correctly get a proper dump of the IIS process so i can then do some more autopsy on it. I would email Tess Ferrandez (the goddess of crash debuging) but I thought I'd try here before I spam her. Can anyone have any suggestions to how I can figure out how to start to debug this issue?

  Read the article

• Adding file to /etc/cron.d doesn't make it run (ubuntu 10.04)

  - by tom

  If I scp a cron file into /etc/cron.d it doesn't run unless I edit the file and change the command. Then crond seems to pick up the cron file. How can I make cron reload its cron files in ubuntu 10.04? 'touch'ing the file doesn't work nor does 'restart cron' or 'reload cron'. My cron file is set to run every minute and logs to a file. Nothing ends up in the log file until I edit the command, and there's no entry for it in /var/log/syslog I'm stumped. Here's my cron file saved to /etc/cron.d/runscript # Runs the script every minute. This is safe because it will exit with success if it's already running * * * * * www-data if [ -f /usr/local/bin/thing ]; then exec /usr/bin/php /usr/local/bin/thing mode:prod -a 14 -d >> /var/log/thing/mything.log 2>&1; else echo `date +'[%D %T]'` "Thing not deployed. Command not run\n" >> /var/log/thing/mything.log; fi &

  Read the article

• centos install / partitioning

  - by ServerSideX

  I'm using NOC-PS to remotely install Centos 6.2 via KVM / IPMI. I'm going to install cPanel as well and they recommend this layout /boot (99MB) swap (2x server RAM) / (remainder) In the o/s install profile within NOC-PS software, it shows as this: part /boot --fstype ext2 --size 250 part pv.01 --size 1 --grow volgroup vg pv.01 logvol / --vgname=vg --size=1 --grow --fstype ext4 --fsoptions=discard,noatime --name=root logvol /tmp --vgname=vg --size=1024 --fstype ext4 --fsoptions=discard,noatime --name=tmp logvol swap --vgname=vg --recommended --name=swap By the time the default partition setup was done installing Centos, I get this [root@server005 ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg-root 532G 907M 504G 1% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 243M 28M 202M 13% /boot /dev/mapper/vg-tmp 1008M 34M 924M 4% /tmp [root@server005 ~]# cat /etc/fstab # # /etc/fstab # Created by anaconda on Fri Dec 7 18:47:24 2012 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg-root / ext4 discard,noatime 1 1 UUID=58b31aaf-5072-4fb1-a858-33bc316fa793 /boot ext2 defaults 1 2 /dev/mapper/vg-tmp /tmp ext4 discard,noatime 1 2 /dev/mapper/vg-swap swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 My question is, how should the NOC-PS install profile look like to get the recommended cPanel partitioning? The server has 16GB RAM, dual 600GB SAS drives and will be used for cPanel shared hosting.

  Read the article

• Utility to grant admin rights to a user in Windows XP for few hours/days?

  - by user15660

  I have two accounts on my windows xp home desktop. The default regular user is used for everything and the 2nd user which has admin rights is used only for installations. I do this to avoid malware infestations during web browsing and limited user account is guarding against online threats to a good extend but many programs refuse to run under limited rights like revo uninstaller. many installs i run from limited user by selectin "run as" from right click context menu of the .exe file. but some apps need admin rights for certain. I use "switch user" to go to admin mode and do the install/uninstall. but the admin user has none of my preferences bookmarks setup nor has my locate32 indexing done and ready for fast search Is there a utility which I can use "run as" login in administration login and use that to grant my limited user admin rights for a limited amount of period like few hours or days? Please help. I guess MS might have closed many doors of it for fear of exploitation of the API. are there any?

  Read the article

< Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >