Search Results

Search found 16598 results on 664 pages for 'device center'.

Page 411/664 | < Previous Page | 407 408 409 410 411 412 413 414 415 416 417 418  | Next Page >

  • Identify SATA hard drive

    - by Rob Nicholson
    Very similar question to: Physically Identify the failed hard drive But for Windows 2003 this time. Scenario: Four identical SATA hard drives plugged into motherboard (no RAID controller here) Configured as single drive in Windows as a spanned volume One of them is starting to fail with error "The driver detected a controller error on \Device\Harddisk3" How do you cross-reference Harddisk3 to the physical SATA connection on the motherboard so you know which drive to replace? I know replacing this drive will trash the spanned array requiring it to be rebuilt anyway so my rough and ready solution is: Delete the spanned partition Create individual partitions on each drive labelled E: F: G: and H: and work out which one is Harddisk3 Power down, remove each disk one at a time, power-up until the drive letter disappears But this seems a rather crude method of identifying the drive. The SATA connectors will be numbered on the motherboard but I appreciate this might not cross-match to what Windows calls them. Thanks, Rob.

    Read the article

  • tradeoffs of iSCSI vs. AFP when using Time Machine with a NAS?

    - by ajit.george
    I'm setting up a home NAS device (Synology DS409) that I'm planning to use for Time Machine backups (amongst other things). What are the tradeoffs between using iSCSI or AFP to mount the backup volume? The Synology wiki suggests that iSCSI is better if the Mac will be frequently disconnected from the network or sleeping, from the point of view of the volume automatically remounting. What about filesystem consistency? Given that unplugging a USB drive without properly unmounting it often requires the Time Machine volume to be repaired, would iSCSI have the same issues? Thanks in advance.

    Read the article

  • Monitor Bonded Interface for Disconnection

    - by bradlis7
    I am trying to monitor for network failures on a machine, and one portion of that is to monitor interfaces that are intended to be active also be "RUNNING". An Ethernet port, such as eth0, will say "RUNNING" if it is physically connected to another device. The problem lies in the bonded interfaces, such as bond0. If all of the ethernet devices are disconnected, it still says that it is running, and it is still pingable. Is this by design, or is my system setup incorrectly? Does the miimon option have something to do with this?

    Read the article

  • OpenVPN Setup - Service Won't Start

    - by Lenwood
    I'm in the process of setting up OpenVPN on a VPS running Debian 6. I've walked step-by-step through this guide twice now, and I can't get the service to start. When I start the service, the error reported in the log file is: Cannot ioctl TUNSETIFF tun: Inappropriate ioctl for device (errno=25) I've searched the web a few times and I'm not finding anything helpful. I've tried: Changing file permissions: no change Deleting the file: get an error stating no file found (errno=2) Making a folder named "tun": get an error stating no file found (errno=2) I've wiped my installation and completed the steps verbatim twice now. I get no errors along the way, just the error above within my log file. The contents of my server.conf file are listed below, minus all the comments for brevity. Can anyone help? port 1194 proto udp dev tun ca ca.crt cert myserver.crt key myserver.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log log openvpn.log verb 3

    Read the article

  • How to play games in widescreen in Windows 7, Dell Studio 1555

    - by blasteralfred
    I have a dell studio 1555 laptop with a GPU inside. The details are below; Hardware details Software details I can play games in widescreen in Vista, but not in 7. I am using Windows 7 Home Premium. I have the latest Catalyst Control Center. Instead of widescreen, the games are running in a classic style, say 1024x768 ratio. When I play need for speed underground, the maximum possible resolution is 1024x768 (all other games are like this). I have no problem with HD videos and anything else. How can I fix this? Thanks in advance...:)

    Read the article

  • How to repair unbootable Fedora install

    - by Cerin
    How do you repair/reinstall Fedora without deleting any existing partitions or data? I was attempting to upgrade some old Fedora 13 servers to 17, following the instructions in the wiki. After the 14-15 upgrade, rebooting resulted in the output: Dropping to debug shell. sh: can't access tty; job control turned off dracut:/# Running dmesg also shows: dracut Warning: No root device "block:/dev/mapper/VolGroup-lv_root" found Googling shows this error is typically related to some weird RAID issues, but my server is a virtual machine not using any RAID. Using a rescue CD, I can chroot /mnt/sysimage, and all packages and data still seems to be there. How do I make the system bootable again?

    Read the article

  • ATI Catalyst setting to stretch Windows XP start bar across both displays

    - by scunliffe
    I have a Lenovo T400 laptop with an ATI Mobility Radeon HD 3400 Series video card, using the ATI Catalyst Control Center to span my Windows XP display over the laptop display and a Dell flatpanel LCD. This works fine, but I'm used to NVIDIA multi-desktop that let me control the "Start bar" to either exist on only 1 screen... be duplicated on both, or (what I want), stretched across both. Is this possible with the ATI card/Catalyst Software? If not, are there any utilities out there that will handle this for me? That is, what I have: +----------+ +----------+ | | | | | Lenovo | | Dell | | (primary)| | | +----------+ | | |Start Tray| | | +----------+ +----------+ And this is what I want: +----------+ +----------+ | | | | | Lenovo | | Dell | | (primary)| | | +----------+ +----------+ |Start | | Tray| +----------+ +----------+

    Read the article

  • CentOS and Broadcom Wireless Drivers

    - by Sami
    Hi, I'm tired of reading, tired of trying to find a solution myself, that's why I decided to post my question. I'm following tutorial located at CentOS Wiki to install driver for my wifi device. However, I'm facing strange error at the begining of the process. make -C /lib/modules/`uname -r`/build/ M=`pwd` make: *** /lib/modules/2.6.18-194.11.3.el5PAE/build/: File not found Does anyone know what I'm doing wrong? This is first time when I try to install Linux on my laptop.

    Read the article

  • How do you manage large web farms?

    - by Andrew Katz
    I have a quickly growing web farm running IIS 7 (30+ servers). All servers are identical copies of each other and all servers are physical. We update the software about once a month, and in the current process, we follow the following steps: Disable server from pool on F5 load balancer. Disable HTTP Keep-alives in IIS so connections drop quickly. Change default directory of website to new folder containing new binaries. Test server Enable HTTP Keep-alives. Enable server in F5 pool. Move to server 2 Microsoft used to have Application Center which was abandoned a while ago. They have made a second attempt with the Web Farm Framework, but this adds as much QA time testing the release package as it saves in the deployment. Has anyone seen a commercial off the shelf application that is tailored for managing and deploying to large web farms? Thanks!

    Read the article

  • Mounting root failed. Dropping into basic maintenance shell

    - by vmsystem
    Hi, I have purchased AMD Phenom X4 955 3.2GHZ processor with supporting gigabyte GA-MA785GM-US2H mother board / 6GB DDR2 RAM / 500GB SATA drive for learning Vmware ESX 3.5 product. In the above configuration, I have installed windows xp 64 bit operating systems and continue to installed vmware workstation 6.5. From the VM workstation, I can able to install ESX3.5 update2, but I unable to start properly, please refer the below mention error. “Mounting root failed. Dropping into basic maintenance shell. To collect logs for VMware, connect a USB storage device and run 'bin/vm-support '. Machine will be rebooted when you exit from this shell.” The same was tested in the windows 2003 Enterprise Edition server / windows 7 32bit / windows 7 64bit also, Please help me to resolve the issue.

    Read the article

  • Solution to wirelessly project tablet desktop?

    - by Robert
    I’m trying to find a device that would allow a windows 7 client to wirelessly connect and display their screen to a projector while still connected to the wireless network. The idea is to allow a professor to still project and display content while walking around the room with their tablet. To date, haven’t been able to find a solution that meets the requirements, has anyone stumbled across one yet? Requirements Must support Windows 7 Must be able to connect to WPA2 Personal(and hopefully enterprise) Must not use any usb dongles – those get lost/damaged given a chance. Goal Wirelessly display screen to projector without cables from tablet/laptop.

    Read the article

  • My computer keeps restart when accept Skype call

    - by hvtuananh
    I'm using latest Skype version (4.2) on Windows XP SP3 My computer keeps restart when I click "Accept" button on Skype call Windows Update is running and I've already installed all updates What's wrong with my computer? How to fix it? EDIT: I only see this error in Event Viewer Event Type: Error Event Source: System Error Event Category: (102) Event ID: 1003 Date: 3/2/2010 Time: 3:47:50 PM User: N/A Computer: TUANANH Description: Error code 1000000a, parameter1 ffffff94, parameter2 0000001c, parameter3 00000000, parameter4 80537bf1. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 53 79 73 74 65 6d 20 45 System E 0008: 72 72 6f 72 20 20 45 72 rror Er 0010: 72 6f 72 20 63 6f 64 65 ror code 0018: 20 31 30 30 30 30 30 30 1000000 0020: 61 20 20 50 61 72 61 6d a Param 0028: 65 74 65 72 73 20 66 66 eters ff 0030: 66 66 66 66 39 34 2c 20 ffff94, 0038: 30 30 30 30 30 30 31 63 0000001c 0040: 2c 20 30 30 30 30 30 30 , 000000 0048: 30 30 2c 20 38 30 35 33 00, 8053 0050: 37 62 66 31 7bf1

    Read the article

  • Windows - Force Wi-Fi to N mode

    - by Frederick Marcoux
    I bought a month ago the D-Link DWA-160 Xtreme N Dual Band USB Adapter and I wonder about the speed. I have a 60Mbps but the speed is never above 300Kbps when I browse Internet or download something. Even from Microsoft or Apple (the fastest server I found). Now on Windows 8, we can see the Wi-Fi stats in Task Manager, there they are: Notice the red rectangle. The signal is 3/5 and I'm about 5 meters far from my router. An Apple Time-Capsule. Also, the connection type is 802.11g, I want N. I made this config in my Device Properties: Does anyone figured out to force the 802.11n in Windows? (Windows 8 preferably)

    Read the article

  • "Bad response to Storage command" when scheduling job with Bacula

    - by Joril
    I have a Bacula setup with 9 clients, and it's working happily. Today I had to add another client, so I went and copied+adapted the existing configuration files from another client, but when I schedule a job for the new client, I get these errors: 20-Mar 17:50 tools-dir JobId 39: Start Backup JobId 39, Job=BackupPresenze2.2012-03-20_17.50.49_04 20-Mar 17:50 tools-dir JobId 39: Using Device "FileStorage" 20-Mar 17:50 presenze2-fd JobId 39: Fatal error: Failed to connect to Storage daemon: bacula.mylan.local:9103 20-Mar 17:50 tools-dir JobId 39: Fatal error: Bad response to Storage command: wanted 2000 OK storage , got 2902 Bad storage From the client I can telnet to bacula.mylan.local:9103 just fine, and jobs for other clients work successfully... What could I check? (Server and client run Ubuntu 10.04, if it's relevant)

    Read the article

  • Netbeans: Install/Activate/Uninstall/Deactivate plugins buttons disabled

    - by Josh
    I recently installed Netbeans 6.9 on a new computer. I went to install the NB Android plugin, which I have on another computer, but I found most of the functionality of the plugins window disabled. The install, uninstall, activate, and deactivate buttons are grayed out. I have included images at the bottom. This hasn't happened to me before, and searching Google hasn't turned up anything useful. I thought it might have been a permission problem so I tried running Netbeans with gksudo but that didn't help. I also thought it might have been something wonky with the Ubuntu Software Center install, so I uninstalled that one, and downloaded Netbeans from the main site and I installed it in my home directory, but it does the same thing. I'm running Xubuntu 10.10 and Netbeans 6.9.1 Available Plugins Tab It won't let me add more than one hyperlink due to a lack of reputation. Installed Tab - http + i.imgur.com/Nhqi4.png

    Read the article

  • ubuntu qcow2 image for local usage

    - by aisbaa
    I'm using kvm and I would like to run ubuntu server on it. My goal is to run db2 database instance for development. Is there ready to use ubuntu qcow2 images online for such purpose? Or should I install it from live cd? I've found this instruction UEC/Images, but at launch I get: $ kvm -fda ${floppy} -drive if=virtio,file=./disk.img -boot a ... Nothing to boot: No such file or directory (http://ipxe.org/...) No more network devices No bootable device. Solution: I havent found pre-installed ubuntu virtual machine image online, so solution is to install it by your self.

    Read the article

  • Recommending simple appliance for DansGuardian, iptables, snort inline

    - by SRobertJames
    I'm currently using a Linksys E2000 with dd-wrt. I'd like to add DansGuardian for Content Filtering and snort-inline for IPS; but those require a more powerful box (mainly, more storage). Can you recommend a good device to use? I'm open to both overwrite-the-firmware (like dd-wrt) and designed-to-be-customized boxes. Requirements: 1. 5+ Ethernet ports, pref. GigE 2. small form factor 3. No noise (office environment) 4. low power 5. Not sure about 802.11 wireless Budget < $400, pref. less.

    Read the article

  • "This file can't be previewed because of an error in the Microsoft Word previewer."

    - by danielson
    The issue is: Outlook 2013 simply will not give a preview of Word (nor Excel) docs in attachments. Never had the issue with Outlook 2010. Using Outlook 2013 on Windows 7 64bit SSD with Word 2010. I did notice that "Microsoft Word" is not listed specifically in Trust Center attachment handling, could that be part of the problem? Excel, Visio, RTF and many more are there. Update: strange, search can be performed in Word attachments... but can't preview Word file. So, Outlook can 'see' Word docs but won't let us have that preview. For reference, here is a similar question I posted in the Microsoft Answers forum.

    Read the article

  • How to play from mic to speakers in Ubuntu Karmic?

    - by vava
    Ok, I have a silly problem. I have few bluetooth headsets lying around and I want to make DYI baby monitor out of them. All I need is for some application to listen to the mic and send it to the speakers. Loopback (even though it doesn't work) is not good enough, it'll send sound from the mic to the speakers in the same device but I need it to go across devices. So does anyone know some application that can do that? I'm looking for something small and easy to use, not jackd or similar.

    Read the article

  • How to tell if OpenGL is really working in Ubuntu 10.04

    - by Jonathan
    I have a lenovo S9e running Intel integrated graphics. Here is my lspci output related to the graphics: 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) Subsystem: Lenovo Device 3870 Flags: bus master, fast devsel, latency 0 Memory at f0580000 (32-bit, non-prefetchable) [size=512K] Capabilities: [d0] Power Management version 2 I want to know how I can make sure OpenGL support is running in full on an Ubuntu 10.04 installation. I have a few hints to think that it is not: The "Desktop Effects" will not load Apps such as stardock, when attempting to use OpenGL rendering, will display black boxes instead of transparency In the games Pioneers, the number-tile icons are suspiciously just black circles Windows games running with Wine will only support software rendering, not hardware rendering When I boot into a Knoppix LiveCD, the desktop effects do work, splendidly, meaning compiz detects my computer as capable. My problem with troubleshooting is that Canonical has basically eliminated the conf-file-based mechanism of X11 as far as I can tell, thus making it even harder to ensure graphics modules are loading properly. How do I debug and test OpenGL on m Ubuntu 10.04 installation?

    Read the article

  • Scripted printer configuration changes

    - by David Steven
    I've got about a dozen Windows XP machines that I need to make a couple specific printer configuration changes to. The printer is "virtual" printer for an electronic delivery service. I'd like to not have to visit each machine individually. I already have the means to execute commands remotely on the machines, I just can't seem to find away to adjust these settings via command line or script. Specifically I need to be able to make the following changes: 1) As an admin user: - Device Settings - Font Substitution Table/Courier New - Change to "Courier" 2) As a specific* user: - Printer Preferences - Paper/Quality - Advanced - Change Graphic/Print Quality to "600 x 600" - Change Document Options/Printer Features/Graphics Mode to "HP-GL/2" *This change is a per user configuration, unless there's some way to make it once. In this situation I only really need it for a specific (different) user on each machine.

    Read the article

  • Does exist an MKV meta tag / metadata editor?

    - by Vittorio
    Hi, I'm looking for an MKV meta tag editor, I'm using PLEX Media Server and PLEX Media Center on my iMac to see movies. PLEX is great because it automatically find and name all my movie library with year, director, gender, original title, description, movie poter art, etc. Unfortunately, it saves all the data only on a app DB file without edit any tag on the MKV files. A 20% of the movies needs to be fixed or PLEX needs help to find exactly the movie name, so if I need to move all my library elsewere, I need to do all the tagging work again. So, does exists MKV meta tag editor? Oh I'm a Mac user

    Read the article

  • Cannot enter BIOS due to broken screen

    - by gamer
    Lately my laptop(hp g42 247sb) screen is damaged, so I hook it up with a external monitor(LG something) and it works fine now. But the only annoying thing is I cannot navigate the BIOS menu for some tweaking because the BIOS not shown on the external monitor,instead, it only shown on the broken laptop screen, and it only output to my external monitor when windwos/os is loged-on. So, is there anyway I can force output during BIOS/BOOT/POST to my external monitor? Things I have done and didn't work: (1)Set my LG monitor as primary display on both window properties and Intel Graphics panel (2)Enter the bios (F10 key) and press the fn+F4 key(change display output). (3)Disable and uninstall my internal screen(broken laptop screen) using device manager and restart, but windows(bios?) install it back on log-on. Please help me!

    Read the article

  • Sharepoint 2007 Event ID 6482

    - by Dave M
    Our two server SharePoint 2007 SP2 farm has an issue. Event ID 6482 appears in the Application log of the Web front end many times a day. Often many time a minute. The full error is from Office SharePoint Server Event Type: Error Event Source: Office SharePoint Server Event Category: Office Server Shared Services Event ID: 6482 Date: 11/12/2009 Time: 3:05:22 PM User: N/A Computer: XXXXXX Description: Application Server Administration job failed for service instance Microsoft.Office.Server.Search.Administration.SearchServiceInstance (36a9b7ef-59aa-4f94-8887-8bf7b56f2f91). Reason: Error during encryption or decryption. System error code 0. Techinal Support Details: System.ArgumentException: Error during encryption or decryption. System error code 0. at Microsoft.Office.Server.Search.Administration.SearchServiceInstance.SynchronizeDefaultContentSource(IDictionary applications) at Microsoft.Office.Server.Search.Administration.SearchServiceInstance.Synchronize() at Microsoft.Office.Server.Administration.ApplicationServerJob.ProvisionLocalSharedServiceInstances(Boolean isAdministrationServiceJob) For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. The SharePoint site appears to be functioning normally and Search returns expected results. Any suggestions would be appreciated

    Read the article

  • Problem whit usb wireless mouse

    - by aiacet
    Recently i have thi problem whit my wireless mouse (Trust model on: www.trust.com/15313). Sometimes when i start the Pc or during a game the pointer/arrow stop to move it. In the Pc start the pointer is blocked on the center of the screen. If I'm lucky i have to chance the USB wirless adapter from port 1 to port 2 but sometimes this trick doesn't work i to use the mouse i have to restart. Like you can see in the productor webpage this mouse don't have the direver but only a tool to solve some problem. Thank you in advance to all the "super-users" that reading this question would be help me Ajax

    Read the article

< Previous Page | 407 408 409 410 411 412 413 414 415 416 417 418  | Next Page >