Search Results

Search found 13331 results on 534 pages for 'fluent interface'.

Page 415/534 | < Previous Page | 411 412 413 414 415 416 417 418 419 420 421 422  | Next Page >

• Mac OS X Client With Static DHCP Assignment Requests Wrong IP via Option 50

  - by Starchy

  I have a number of Mac (and a few Linux) laptops getting DHCP from a Force10 layer 3 switch, the only DHCP server on the subnet. There's a global dynamic pool, and for each full-time employee's laptop I have a single IP static pool set by MAC address. One and only one of the clients, running OS X 10.7.5, consistently fails to get a static assignment. The MAC address in the static pool definition has been carefully re-checked. Running tcpdump on a mirrored port when the laptop connects, I see that it is specifically requesting 10.100.0.252 (a dynamic address): 11:32:10.108280 IP (tos 0x0, ttl 255, id 28293, offset 0, flags [none], proto UDP (17), length 328) 0.0.0.0.bootpc > broadcasthost.bootps: [udp sum ok] BOOTP/DHCP, Request from 3c:07:54:xx:xx:xx (oui Unknown), length 300, xid 0x1399da89, Flags [none] (0x0000) Client-Ethernet-Address 3c:07:54:xx:xx:xx (oui Unknown) Vendor-rfc1048 Extensions Magic Cookie 0x63825363 DHCP-Message Option 53, length 1: Request Parameter-Request Option 55, length 9: Subnet-Mask, Default-Gateway, Domain-Name-Server, Domain-Name Option 119, LDAP, Option 252, Netbios-Name-Server Netbios-Node MSZ Option 57, length 2: 1500 Client-ID Option 61, length 7: ether 3c:07:54:xx:xx:xx Requested-IP Option 50, length 4: 10.100.0.252 Lease-Time Option 51, length 4: 7776000 Hostname Option 12, length 10: "host-name" END Option 255, length 0 PAD Option 0, length 0, occurs 8 I haven't been able to find any extra system prefs or unusual software on the laptop. Disabling the interface and rebooting or temporarily setting the IP manually both fail to make any difference. Any suggestions appreciated.

  Read the article

• Bridged network on OS X only gets UDP broadcast traffic

  - by a paid nerd

  I've created a bridged network Mac OS X 10.8.5 using ifconfig and TUNTAP for OS X to bridge my wireless connection, en0, with a virtual interface, tap0, which I can use for guest VMs: $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 28:cf:xx:xx:xx:xx inet6 xxxx::xxxx:xxxx:xxxx:xxxx%en0 prefixlen 64 scopeid 0x4 inet 192.168.100.64 netmask 0xffffff00 broadcast 192.168.100.1 media: autoselect status: active bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) However, if I tcpdump -i tap0, I only see broadcast traffic. Shouldn't I see a mirror of everything on en0? (192.168.100.33, the host doing the broadcasting, is another unrelate, noisy server on my LAN.) (I asked a similar question here and will probably close it.)

  Read the article

• Best Practical RT, sorting email into queues automatically using procmail

  - by user52095

  I'm trying to get incoming e-mail to automatically go directly into whichever queue/ticket they are related to or create a new one if none exist and the right queue e-mail setup in the web interface is used. I will have too many queues to have two line items within mailgate per queue. A similar issue was discussed here (http://serverfault.com/questions/104779/procmail-pipe-to-program-otherwise-return-error-to-sender), but I thought it best to open a new case instead of tagging on what appeared to be an answer to that person's query. I'm able to send and receive e-mail (via PostFix) to the default rt user and this user successfully accepts all e-mail for the relative domain. I have no idea where the e-mail goes - it's successfully delivered, but it does not update existing tickets (with a Subject line match) and it does not create any new. Here's and example of my ./procmail.log: procmail: [23048] Mon Aug 23 14:26:01 2010 procmail: Assigning "MAILDOMAIN=rt.mydomain.com " procmail: Assigning "RT_MAILGATE=/opt/rt3/bin/rt-mailgate " procmail: Assigning "RT_URL=http://rt.mydomain.com/ " procmail: Assigning "LOGABSTRACT=all " procmail: Skipped " " procmail: Skipped " " procmail: Assigning "LASTFOLDER={ " procmail: Opening "{ " procmail: Acquiring kernel-lock procmail: Notified comsat: "rt@18337:./{ " From [email protected] Mon Aug 23 14:26:01 2010 Subject: RE: [RT.mydomain.com #1] Test Ticket Folder: { 1616 Does the notified comsat portion mean that it notified RT? The contents of my ./procmailrc: #Preliminaries SHELL=/bin/sh #Use the Bourne shell (check your path!) #MAILDIR=${HOME} #First check what your mail directory is! MAILDIR="/var/mail/rt/" LOGFILE="home/rt//procmail.log" LOG="--- Logging ${LOGFILE} for ${LOGNAME}, " VERBOSE=yes MAILDOMAIN="rt.mydomain.com" RT_MAILGATE="/opt/rt3/bin/rt-mailgate" #RT_MAILGATE="/usr/local/bin/rt-mailgate" RT_URL="http://rt.mydomain.com/" LOGABSTRACT=all :0 { # the following line extracts the recipient from Received-headers. # Simply using the To: does not work, as tickets are often created # by sending a CC/BCC to RT TO=`formail -c -xReceived: |grep $MAILDOMAIN |sed -e 's/.*for *<*\(.*\)>* *;.*$/\1/'` QUEUE=`echo $TO| $HOME/get_queue.pl` ACTION=`echo $TO| $HOME/get_action.pl` :0 h b w |/usr/bin/perl $RT_MAILGATE --queue $QUEUE --action $ACTION --url $RT_URL } I know that my get_queue.pl and get_action.pl scripts work, as those have been previously tested. Any help and/or guidance you can give would be greatly appreciated. Nicôle

  Read the article

• How can I remotely tell what brand/model internal SCSI card is installed in a machine?

  - by edmicman

  I am doing some consulting work for a previous employer upgrading and migrating old servers to new hardware. There is an existing file server (HP ProLiant DL380) that has an tape backup drive connected; it is using a SCSI interface and I'm pretty sure it's using an internal SCSI card. They are upgrading to a new server hardware (HP ProLiant DL160 G6). The old server is 2U, the new one 1U and we would want to move the tape drive to the new server, too. I'm trying to figure out if the SCSI card in the old server would be able to be installed in the new one or if we'll need to source a new card; mostly I don't know for sure the height of the card and if it's low-profile enough that it would fit in the new server. There is not much of a technical resource onsite and the old server is in-use anyway so I would like to avoid making a trip in myself or trying to have someone onsite pop open the case and tell me what card is there. It's running Windows Server 2003 - is there a way to tell from say Device Manager what make and model the SCSI card might be? Or any other system diagnostic program or something that would give me hardware info like that? Thanks for any info!

  Read the article

• How to write re-usable puppet definitions?

  - by Oliver Probst

  I'd like to write a puppet manifest to install and configure an application on target servers. Parts of this manifest shall be re-usable. Thus I used define for defining my re-usable functionality. Doing so, I've always the problem that there are parts of the definition which are not re-usable. A simple example is a bunch of configuration files to be created. These file must be placed in the same directory. This directory must be created only once. Example: nodes.pp node 'myNode.in.a.domain' { mymodule::addconfig {'configfile1.xml': param => 'somevalue', } mymodule::addconfig {'configfile2.xml': param => 'someothervalue', } } mymodule.pp define mymodule::addconfig ($param) { $config_dir = "/the/directory/" #ensure that directory exits: file { $config_dir: ensure => directory, } #create the configuration file: file { $name: path => "${config_dir}/${name}" content => template('a_template.erb'), require => File[$config_dir], } } This example will fail, because now the resource file {$config_dir: is defined twice. As far as I understood, it is required to extract these parts into a class. Then it looks like this: nodes.pp node 'myNode.in.a.domain' { class { 'mymodule::createConfigurationDirectory': } mymodule::addconfig {'configfile1.xml': param => 'somevalue', require => Class ['mymodule::createConfigurationDirectory'], } mymodule::addconfig {'configfile2.xml': param => 'someothervalue', require => Class ['mymodule::createConfigurationDirectory'], } } But this makes my interface hard use. Every user of my module has to know, that there is a class which is additionally required. For this simple use case the additional class might be acceptable. But with growing module complexity (lots of definitions) I'm a bit afraid of confusing the modules user. So I'd like to know is there a better way to handle this dependencies. Ideally, classes like createConfigurationDirectory are hidden from the user of the modules api. Or are there some other "Best Practices"/Patterns handling such dependencies?

  Read the article

• Which IP should I use for my nameserver

  - by Luke Bream

  Sorry to ask whats probably very obvious question. I have just got a new server that is fantastically cheap but unfortunatly doesnt come with any technical support and Im very out of my depth ! My hosting company has provided the following information... Below you will find your additional IP addresses added to the server 5.9.36.51 Please note that you can use the subnet only for this server. IP: 5.9.225.64 /27 Mask: 255.255.255.224 Broadcast: 5.9.225.95 Useable IP addresses: 5.9.225.65 to 5.9.225.94 It has cPanel with WHM and im going through the setup... I have a number of questions... my domian is purchased from godaddy and I want to use it as the name server. Question 1: Which IP or IP's do I enter into the godaddy interface for ns1.mydomian.com ns2.mydomain.com Question 2: In the WHM nameserver setup what do I enter for... Please enter an IP address for each of your nameservers. ns1.mydomain.com ?????? ns2.mydomain.com ?????? Add "A Entries" for Hostname IP for Entry: ????????? Thanks for aany help you can give Luke

  Read the article

• Configuring port forwarding for SSH - no response outside LAN

  - by WinnieNicklaus

  I recently moved, and at the same time purchased a new router (Linksys E1200). Prior to the move, I had my old router set up to forward a port for SSH to servers on my LAN, and I was using DynDNS to manage the external IP address. Everything worked great. I moved and set up the new router (unfortunately, the old one is busted so I can't try things out with it), updated the DynDNS address, and attempted to restore my port forwarding settings. No joy. SSH connections time out, and pings go unanswered. But here's the weird part (i.e., key to the whole thing?): I can ping and SSH just fine from within this LAN. I'm not talking about the local 192.168.1.* addresses. I can actually SSH from a computer on my LAN to the DynDNS external address. It's only when the client is outside the LAN that connections are dropped. This surely suggests a particular point of failure, but I don't know enough to figure out what it is. I can't figure out why it would make a difference where the connections originate, unless there's a filter for "trusted" IP addresses, which is perhaps just restricted to my own. No settings have been touched on the servers, and I can't find any settings suggesting this on the router admin interface. I disabled the router's SPI firewall and "Filter anonymous traffic" setting to no avail. Has anyone heard of this behavior, and what can I do to get past it?

  Read the article

• Fast Ethernet module for Cisco 2620

  - by Kenny Rasschaert

  I have a Cisco 2620 Router. It comes with one fast ethernet port built in (circled in red), and one old AUI ethernet module is installed (circled in blue). I figure I can put a transceiver on the AUI interface to get a second RJ45 connector. What I'd really like to have is a second fast ethernet connector. The ideal candidate to achieve this would be the NM-1FE-TX module. Cisco claims on their website that this module is not suitable for the Cisco 2620 and Cisco 2620XM. It says so in "Table 2 Physical Limitation of Serial Modules per Chassis". Indeed, this module was designed for the 3600 series of routers. I've seen claims on the internet, however, of people having this module on a 2620XM, and it being fully functional. This claim gains some credibility because of the fact that in Cisco's own Packet Tracer software, you can install this module on the 2620XM router. I'm looking for a definitive answer. Will this module work on a Cisco 2620? Is there perhaps another way to get a second fast ethernet port on this device?

  Read the article

• HP Procurve 2610 intervlan routing

  - by user19039

  Can anyone tell me why inter vlan routing is working for all vlans except my newly created vlan 4/ I have an hp procurve 2610. Any help would be appreciated. I have basically this 1 switch with all unmanaged switches attached to the core. We have a second 2610 on port 28 Running configuration: ; J9085A Configuration Editor; Created on release #R.11.25 hostname "Core_HP" interface 22 speed-duplex 100-full exit ip routing snmp-server community "public" Unrestricted vlan 1 name "DEFAULT_VLAN" untagged 1-12,17-22,26-27 ip address 192.168.4.6 255.255.255.0 tagged 25 no untagged 13-16,23-24,28 exit vlan 2 name "WAN" untagged 28 ip address 10.254.254.3 255.255.255.0 exit vlan 3 name "Wireless" untagged 13-16,24 ip address 192.168.7.6 255.255.255.0 ip helper-address 192.168.4.2 tagged 27 exit vlan 35 name "guest" untagged 23 tagged 24 exit vlan 4 name "esxi" untagged 25 ip address 10.10.1.1 255.255.248.0 exit ip route 192.168.5.0 255.255.255.0 10.254.254.1 ip route 192.168.6.0 255.255.255.0 10.254.254.1 ip route 0.0.0.0 0.0.0.0 192.168.4.10 show ip route IP Route Entries Destination Gateway VLAN Type Sub-Type M etric Dist. ------------------ --------------- ---- --------- ---------- - --------- ----- 0.0.0.0/0 192.168.4.10 1 static 1 1 10.10.0.0/21 esxi 4 connected 0 0 10.254.254.0/24 WAN 2 connected 0 0 127.0.0.0/8 reject static 0 250 127.0.0.1/32 lo0 connected 0 0 192.168.4.0/24 DEFAULT_VLAN 1 connected 0 0 192.168.5.0/24 10.254.254.1 2 static 1 1 192.168.6.0/24 10.254.254.1 2 static 1 1 192.168.7.0/24 Wireless 3 connected 0 0 show ip Internet (IP) Service IP Routing : Enabled Default TTL : 64 Arp Age : 20 VLAN | IP Config IP Address Subnet Mask Prox y ARP ------------ + ---------- --------------- --------------- ---- ----- DEFAULT_VLAN | Manual 192.168.4.6 255.255.255.0 No WAN | Manual 10.254.254.3 255.255.255.0 No Wireless | Manual 192.168.7.6 255.255.255.0 No esxi | Manual 10.10.1.1 255.255.248.0 No guest | Disabled

  Read the article

• Configuring port forwarding for SSH - no response outside LAN [migrated]

  - by WinnieNicklaus

  I recently moved, and at the same time purchased a new router (Linksys E1200). Prior to the move, I had my old router set up to forward a port for SSH to servers on my LAN, and I was using DynDNS to manage the external IP address. Everything worked great. I moved and set up the new router (unfortunately, the old one is busted so I can't try things out with it), updated the DynDNS address, and attempted to restore my port forwarding settings. No joy. SSH connections time out, and pings go unanswered. But here's the weird part (i.e., key to the whole thing?): I can ping and SSH just fine from within this LAN. I'm not talking about the local 192.168.1.* addresses. I can actually SSH from a computer on my LAN to the DynDNS external address. It's only when the client is outside the LAN that connections are dropped. This surely suggests a particular point of failure, but I don't know enough to figure out what it is. I can't figure out why it would make a difference where the connections originate, unless there's a filter for "trusted" IP addresses, which is perhaps just restricted to my own. No settings have been touched on the servers, and I can't find any settings suggesting this on the router admin interface. I disabled the router's SPI firewall and "Filter anonymous traffic" setting to no avail. Has anyone heard of this behavior, and what can I do to get past it?

  Read the article

• Problem with TL-R480T+ and static routes

  - by Globulopolis

  Hi! I've some question about this router. Before starting, some configurations, specified by my provider. Wan1 VPN IP - 192.168.172.84 Mask - 255.255.255.0 Gateway - 192.168.172.253 DNS - 195.110.6.7 Wan2 Dynamic IP DHCP - 168.120.1.34 Mask - 255.255.255.0 Router IP 192.168.1.1 Computer IP 192.168.1.7 Routes: route -p add 192.168.0.0 mask 255.255.0.0 192.168.172.253 route -p add 195.110.6.0 mask 255.255.254.0 192.168.172.253 route -p add 88.135.112.0 mask 255.255.240.0 192.168.172.253 route -p add 178.219.160.0 mask 255.255.240.0 192.168.172.253 For first provider I need to provide a routes. 'Cause router does not support different routes for different WAN interfaces I put them in "Static routes". But when I try to save them I've got an error: Destination IP address can not be set in a same subnet with the WAN or LAN IP address. If I change IP's to local like 192.168.x.x router tell me: Gateway must be set in a same subnet with WAN or LAN IP address. Changing mask on WAN1 interface to 255.255.0.0 doesn't help. Any ideas? PS! Or maybe I'm must email to TP-Link support?

  Read the article

• Virtual host config issues in osx 10.7 server app

  - by Benno

  I have two mac mini lion servers setup to run as production and staging machines. My sysadmin decided on these machines over the previous CentOS we had because it had an "interface" to be able to manage it, rather than just the terminal. To be honest, I prefer the terminal. My problem is, the mac osx 10.7 server.app seems to be having issues with the creation of virtual hosts in the 'Web' section. It seems VERY touchy. For example, I cannot create a http virtual host first. I have to create a https host first with a unique dns name 9e..g vuly6), then create the http host with a different dns name to the first (e.g. www), or it appears to override it the first one, even though one is ssl and one is non-ssl. Further, it seems to override perfectly good configurations at random. For example, the default sites directory is usually /Users/default/Sites/Customsites or something, but sometimes when I load the server.app it changes to /var/empty. Also, if I change or add extra virtual hosts after the first one or two, it starts to mess up and the first two virtual hosts start having issues. Has anyone had any experience with setting up virtual hosts via this app? Am I able to manually create these virtual hosts, without using the app, and without the app overriding my settings when I restart apache?

  Read the article

• Fetch videos from sony handycam to linux

  - by bstpierre

  I've got a Sony Handycam DCR-DVD101. When I plug connect the USB cable to my laptop (Ubuntu 10) it doesn't mount any storage device. If I run usb-devices, I see: T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=054c ProdID=00c1 Rev=01.00 S: Manufacturer=SONY S: Product=Storage Device C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=05 Prot=50 Driver=usb-storage The driver says usb-storage, but I'm not sure how to get the device mounted. Is there a way to make this work? Update: checking dmesg, I see: [259072.576559] usb 2-1.1: new high speed USB device using ehci_hcd and address 6 [259072.687200] usb 2-1.1: configuration #1 chosen from 1 choice [259072.836188] Initializing USB Mass Storage driver... [259072.836476] scsi5 : SCSI emulation for USB Mass Storage devices [259072.836632] usb-storage: device found at 6 [259072.836636] usb-storage: waiting for device to settle before scanning [259072.836660] usbcore: registered new interface driver usb-storage [259072.836666] USB Mass Storage support registered. [259077.830410] usb-storage: device scan complete [259077.832343] scsi 5:0:0:0: CD-ROM SONY DDX-A1010 R1.0 PQ: 0 ANSI: 0 [259077.888167] sr1: scsi3-mmc drive: 0x/0x pop-up [259077.888446] sr 5:0:0:0: Attached scsi CD-ROM sr1 [259077.888593] sr 5:0:0:0: Attached scsi generic sg2 type 5 [259080.002079] sr 5:0:0:0: [sr1] Unhandled sense code [259080.002085] sr 5:0:0:0: [sr1] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [259080.002091] sr 5:0:0:0: [sr1] Sense Key : Blank Check [current] [259080.002097] sr 5:0:0:0: [sr1] Add. Sense: No additional sense information [259080.002104] sr 5:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 00 00 [259080.002117] end_request: I/O error, dev sr1, sector 0 [259080.002123] Buffer I/O error on device sr1, logical block 0 [259080.002128] Buffer I/O error on device sr1, logical block 1 Those I/O errors don't look good, is there any hope?

  Read the article

• Having trouble setting up my router

  - by indyK1ng

  I just moved into my apartment and the Internet connection is working. It's Comcast in case that matters. Anyway, I'm having trouble setting up my wireless router (Netgear WNR2000) to work with it. Are there any settings that I could be missing? I currently have it set up to use a static IP address and I found the DNS servers I'm supposed to use and the Internet light is green, but I can't get out to the Internet. When I am trying, I'm connecting to an Ethernet port on the back of my router. Is there a setting I'm missing or a setting that I have set wrong? I used the automatic set up wizard to learn that it's a static IP address. Any help would be appreciated. I am currently only able to use my Linux machine, so please make any help in Linux commands. Yes, I can connect to the Internet if I connect to the modem directly and I've been using the web interface when I'm connected to the router, so I suppose I can ping the router. My router detected the connection as using a static IP address, so I connected to the modem directly and figured out what my IP address, gateway, and mask were as well as DNS servers.

  Read the article

• Is there a small business router that shows bandwidth usage graphs in the admin panel?

  - by Robert Drake

  I support a large number of public libraries that are having their networks upgraded in response to a grant application. These libraries are generally home to between 6-15 computers and have little or no tech services either onsite or contracted remotely. In order to justify current and future purchases, a number of the libraries have requested routers that can provide bandwidth usage graphs that they can show to their managing boards. Is there a small business router that displays traffic graphs in the router administration web interface? The router needs to suppport DHCP and basic firewalling. No other features are required. Further, the reports just need to show overall trends. It is not necessary to show traffic by IP, by protocol/application, or by time of day. They just need an overall week to week, month to month, trend line. I'm familiar with MRTG/PRTG/tools that collect SNMP data from the router, but the libraries don't have the expertise for the configuration. I've considered installing the tomato firmware on some cheap home/home office routers, but if there's a commercial product that can be purchased that would be significantly simpler. Also the library boards would be much more likely to approve the purchase of a commercial product over a 'hacked' one. Any assistance would be appreciated.

  Read the article

• NATing IPv4 while routing IPv6

  - by Hugo

  I've the following setup: client(s) <---> (eth0) router (eth1) <---> wan I have a static IPv4 address and a /48 IPv6 address block. I need to connect all the clients to (wan). Each client will have it's own public IPv6. Meanwhile, I need to NAT those same clients over to (wan). Everything IPv4-related and the NAT are working fine. The IPv6 communication to/from (eth0)<-(clients) works fine, as does the IPv6 communication from (eth1)<-(wan) works fine. To provide IPv6 to all my clients, I've thought of too choices: Having the router as a gateway, which different IP on each interface. This sounds like I need to tell my ISP to route the entire block through that single IP, so it's not really an option. Transparently pass IPv6 packets to/from eth0<-eth1, so all clients can communicate with the upstream gateway (I would actually have a switch here if it weren't for the need to remain IPv4 compatible). So, since I've opted for the second choice, I'm in doubt: How can I pass all IPv6 traffic from eth0 to eth1 transparently? What I need is a level 3 bridge, but linux's bridgeutils create a level 2 bridge (which would bridge ipv4 as well, and I can't have that). This is a DD-WRT device, but it's pretty much an embeded linux, so most suggestions that would work on linux are welcome. Thanks.

  Read the article

• How can find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• Pinging an external server through OpenVPN tunnel doesn’t work

  - by qdii

  I have an OpenVPN server and a client, and I want to use this tunnel to access not only 10.0.8.0/24 but the whole internet. So far, pinging the server from the client through the tun0 interface works, and vice versa. However, pinging www.google.com from the client through tun0 doesn’t work (all packets are lost). I figured that I should configure the server so that any packet coming from tun0 in destination of the internet be forwarded, so I came up with this iptables config line: interface_connecting_to_the_internet='eth0' interface_openvpn='tun0' internet_ip_address=`ifconfig "$interface_connecting_to_the_internet" | sed -n s'/.*inet \([0-9.]*\).*/\1/p'` iptables -t nat -A POSTROUTING -o "${interface_connecting_to_the_internet}" -j SNAT --to-source "${internet_ip_address}" echo '1' > /proc/sys/net/ipv4/ip_forward Yet, this doesn’t work, the packets are still lost and I am wondering what could possibly be wrong with my setup. Some details: ip route gives on the server: default via 176.31.127.254 dev eth0 metric 3 10.8.0.0/24 via 10.8.0.2 dev tun0 10.8.0.2 dev tun0 proto kernel scope link src 10.8.0.1 127.0.0.0/8 via 127.0.0.1 dev lo 176.31.127.0/24 dev eth0 proto kernel scope link src 176.31.127.109 ip route gives on the client: default via 192.168.1.1 dev wlan0 proto static 10.8.0.1 via 10.8.0.5 dev tun0 10.8.0.5 dev tun0 proto kernel scope link src 10.8.0.6 127.0.0.0/8 via 127.0.0.1 dev lo scope link 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.109 client uses wifi adapter wlan0 and TUN adapter tun0. server uses ethernet adapter eth0 and TUN adapter tun0. the VPN spans on 10.0.8.0/24 both client and linux are using Linux 3.6.1.

  Read the article

• osx bash grep - finding search terms in a large file with one single line

  - by unsynchronized

  Is there simple unix command line i can enter which lets me isolate say 512 bytes either side of a search term, even if there is only one "line" in a very large text file? Ok, this should be easy. Famous last words. I'm not that familiar with grep, but it seems it is mainly used to filter out lines in the input that contain search terms. I have a very large json file that I downloaded that i want to search for a particular term. before you click the link - it's over 244MB so be warned - it is from the internet wayback machine and contains lists of zip files of archived photos. i am trying to find mine. Their web interface is broken, so i found the json file that they make public here - it's the last one on the list. when i grep looking for my username, it finds it, but proceeds to dump that line to the console. the problem is that line is 244MB long, and it's the only line in the file. i tried using less, but could not get that to do much - it's very slow, and seems to have the same issue. is there simple unix command line i can enter which lets me isolate say 512 bytes either side of a search term?

  Read the article

• PHP 5.3.5 Windows installer missing php_ldap.dll

  - by nmjk

  I'm working with Windows Server 2008, Apache 2.2. I'm using php-5.3.5-Win32-VC6-x86.msi as the installer, using the threadsafe version. I've gone through the install process four or five times just to make sure that I'm not missing anything ridiculous, but I don't think I am. The problem is that the php_ldap.dll extension simply doesn't seem to exist. It's not present in the installer interface (where the user is asked to choose which extensions to install), and it definitely doesn't appear in the ext/ directory after install. I found a lot of mentions of this issue for 5.3.3, including links to download the extension individually. Those links no longer exist, of course, and besides: they were for 5.3.3. I'd really rather use an extension that belongs with PHP 5.3.5. Anyone else encounter this problem? Any ideas as to what's going wrong? Anyone seen acknowledgement by the PHP folks that the file is indeed missing, and that it's an oversight? It's quite a frustration because the server I'm building has no purpose if I don't have PHP LDAP support. Cheers all, and thanks in advance for your assistance.

  Read the article

• How do photoshop slices and layer comps interact?

  - by Steve314

  I'm interested in using Photoshop (I have CS2) for some user interface design. I was hoping to be able to use slices and layer comps to mark out particular elements, and use Javascript scripting to export multiple graphics files and text descriptions (positions and sizes of slices mainly) that will be used by my program. My problem is that I've never used Photoshop for web design, or otherwise used slices, and I'm not confident that I understand how they interact with layer comps. This is what I believe (and hope) is correct... Manual slices aren't affected by layer comps in any way - they aren't saved as part of a layer comp. The same manual slices will be active irrespective of which layer comp is selected. Layer-based slices aren't directly affected by layer comps, but they are indirectly affected in that the layer comp saves details of layer position and style. Thus selecting a layer comp may move a layer and change its style, affecting the location and size of its layer-based slice, or may effectively disable the slice by hiding the layer. Automatic slices aren't directly affected by layer comps, but are indirectly affected due to changes to the layer-based slices. So, layer based slices (which are my main interest) may move, may change size (to accomodate a style such as a drop shadow), and may be effectively disabled by the layer being hidden. Other details (and all details of manual slices) will remain constant irrespective of which layer comp is active. Is that correct?

  Read the article

• Excel file growing huge (>150 MB)

  - by Josh

  There is one particular Excel file that is used by a number of employees at my company. It is edited from both Excel 2003 and 2007, with the "Sharing" feature turned on to allow multiple writers at once. The file has a decent amount of data on several sheets with some basic formatting, and used to be about 6MB, which seems reasonable for its content. But after a few weeks of editing, the file grew to 10, then 20 MB, and eventually skyrocketed to more than 150 MB, even though it still has about the same amount of data as before. It now takes 5-10 minutes to open it, and that much time again to save it. The first time this happened, I copied the content of each sheet into a new, blank workbook, and saved the new workbook; this brought it back down to about 6MB. Now, it has blown up again. The workbook uses the "Data Validation" feature to limit the values in certain columns to the contents of a few named ranges. Copying all the data into a new workbook means re-setting up all the data validation, which is a pain and not something that we want to do every month. As a troubleshooting step, I tried saving the file in "XML Spreadsheet 2003" format, hoping to get some insight into what was being stored. Sure enough, the file was almost a gig, and almost all of the 10 million lines look like this: <NamedCell ss:Name="Z_21D5114F_E50C_46AC_AA4F_C3FF540C717F_.wvu.FilterData"/> <NamedCell ss:Name="Z_1EE2BA5E_3011_4F9A_8ACD_E58835250FC4_.wvu.FilterData"/> <NamedCell ss:Name="Z_1E3BDCEA_6A72_4ECC_BF4F_7B03CC66181E_.wvu.FilterData"/> I've seen a few VBScripts online to manage and enumerate named cells that are hidden in Excel's built-in interface, though I wonder how they'd handle my 10 million named cells. What I really need, though, is an understanding of why this keeps happening. What actions in excel could be causing this?

  Read the article

• Stop Picasa (Mac) from scanning my harddrive

  - by Bodyscanner

  I want to use Picasa desktop app instead of the tedious & clunky web interface to share a couple of photos. Every time I launch Picasa it proceeds to open an annoying pop-up/tool-tip which flicks through every file on my HD using <=95% of CPU. I don't want this so I click the X. It appears again. I try to drag it somewhere less annoying onscreen but it pings back. I look in prefs for an option to turn it off. I give up and quit app until a new build comes out, which I download and repeat the above. WTF?! I understand Google can't be as cool as Apple - iPhoto isn't perfect by any means but at least it looks nice and 'just works'. I want to launch Picasa, not have it go through everything, not have 1000's of random pics and HD cruft on display in the list, and then perhaps drag in a few photos and upload them. Any idea of if that is possible? </rant>

  Read the article

• Mysql server won't start - no logs

  - by Owen

  After a restart, mysql won't start. sudo service mysql start gives start: Job failed to start and the logs are empty, so I have no idea where to start. I'm pretty sure permissions problems are taken care of. Edit: All disks have at least 1G of space and sh -x /etc/init.d/mysql start gives me: + set -e + basename /etc/init.d/mysql + INITSCRIPT=mysql + JOB=mysql + [ mysql = upstart-job ] + [ -z start ] + COMMAND=start + shift + [ -z ] + ECHO=echo + echo Rather than invoking init scripts through /etc/init.d, use the service(8) Rather than invoking init scripts through /etc/init.d, use the service(8) + echo utility, e.g. service mysql start utility, e.g. service mysql start + echo + echo Since the script you are attempting to invoke has been converted to an Since the script you are attempting to invoke has been converted to an + echo Upstart job, you may also use the start(8) utility, e.g. start mysql Upstart job, you may also use the start(8) utility, e.g. start mysql + grep -q start/ + status mysql + [ -z ] + [ start = stop ] + [ -n ] + start mysql start: Rejected send message, 1 matched rules; type="method_call", sender=":1.105" (uid=1000 pid=3208 comm="start mysql ") interface="com.ubuntu.Upstart0_6.Job" member="Start" error name="(unset)" requested_reply="0" destination="com.ubuntu.Upstart" (uid=0 pid=1 comm="/sbin/init")

  Read the article

• SSH client and Command Prompt replacements Windows look-and-feel

  - by Oddthinking

  The Problem I've worked exclusively in Windows. I can handle that. I've worked exclusively in DOS (a long time ago!). I can handle that. I've worked exclusively in Unix. I can handle that. Right now, I am developing a command-line (python) application on a Windows machine, testing it in a DOS box (i.e. Windows' Command prompt), and then deploying it to Linux, and running it with PuTTY. I cannot handle that. My productivity drops dramatically when CTRL-C cuts in one window (Windows) and kills the process in another (DOS, Linux). My productivity drops dramatically when Enter copies the selection in one window (DOS), and deletes the selection in another (Windows), and runs the current half-edited command in the third (PuTTY). My productivity drops dramatically when I cannot hit Undo, Home or End. The Solution I am Seeking An SSH/Bash command-line client that runs on Windows and, to the extent possible, uses all the standard Windows shortcuts (Cut, Copy, Paste, Undo, Home, End, Insert, Shift-Arrows, etc.) work on a bash command line. Bonus points if it puts the cursor between letters, rather than on them. Plus, an equivalent DOS command-line drop-in that runs on Windows, and provides the same interface. I appreciate there may need to be special buttons to actually transfer CTRL codes (like CTRL-C) through in the cases I need them. I suspect the SSH client will need to be specific to a shell (so it knows when it is at the command prompt, and when it is inside a running app.) I know there are many SSH clients, but I am looking for advice for a particular need. PuTTY feels like an escape route for Unix programmers stuck on Windows. I am the opposite. Can anyone recommend one (or maybe a combination of an SSH client and an Command-Line replacement)?

  Read the article

< Previous Page | 411 412 413 414 415 416 417 418 419 420 421 422  | Next Page >