Search Results

Search found 13331 results on 534 pages for 'fluent interface'.

Page 418/534 | < Previous Page | 414 415 416 417 418 419 420 421 422 423 424 425  | Next Page >

• Can't remove route from routing table

  - by anon

  (I am on Windows Server 2003.) I see a couple of unusual entries in my routing table that I would like to remove: Network Destination Netmask Gateway Interface Metric XXX.27.44.1 255.255.255.255 127.0.0.1 127.0.0.1 20 XXX.27.255.255 255.255.255.255 XXX.27.44.1 XXX.27.44.1 20 All the "XXX"'s are the same octet. I would strongly prefer NOT to clear the routing table, since this is a production server. Here is what I've tried: route delete XXX.27.44.1 The route specified was not found. route delete XXX.27.44.1 mask 255.255.255.255 127.0.0.1 metric 20 The route specified was not found. route delete XXX.27.255.255 The route specified was not found. route delete XXX.27.255.255 mask 255.255.255.255 XXX.27.44.1 metric 20 The route specified was not found. I also tried adding the routes in hopes that I could delete them: route add XXX.27.44.1 mask 255.255.255.255 127.0.0.1 metric 20 The route addition failed: The parameter is incorrect. route add XXX.27.255.255 mask 255.255.255.255 XXX.27.44.1 metric 20 The route addition failed: The parameter is incorrect. Bonus question: What do these entries do, and how did they get there?

  Read the article

• Forwarding HTTP Request with Direct Server Return

  - by Daniel Crabtree

  I have servers spread across several data centers, each storing different files. I want users to be able to access the files on all servers through a single domain and have the individual servers return the files directly to the users. The following shows a simple example: 1) The user's browser requests http://www.example.com/files/file1.zip 2) Request goes to server A, based on the DNS A record for example.com. 3) Server A analyzes the request and works out that /files/file1.zip is stored on server B. 4) Server A forwards the request to server B. 5) Server B returns file1.zip directly to the user without going through server A. Note: steps 4 and 5 must be transparent to the user and cannot involve sending a redirect to the user as that would violate the requirement of a single domain. From my research, what I want to achieve is called "Direct Server Return" and it is a common setup for load balancing. It is also sometimes called a half reverse proxy. For step 4, it sounds like I need to do MAC Address Translation and then pass the request back onto the network and for servers outside the network of server A tunneling will be required. For step 5, I simply need to configure server B, as per the real servers in a load balancing setup. Namely, server B should have server A's IP address on the loopback interface and it should not answer any ARP requests for that IP address. My problem is how to actually achieve step 4? I have found plenty of hardware and software that can do this for simple load balancing at layer 4, but these solutions fall short and cannot handle the kind of custom routing I require. It seems like I will need to roll my own solution. Ideally, I would like to do the routing / forwarding at the web server level, i.e. in PHP or C# / ASP.net. However, I am open to doing it at a lower level such as Apache or IIS, or at an even lower level, i.e. a custom proxy service in front of everything. Thanks.

  Read the article

• weird routes automatically being added to windows routing table

  - by simon

  On our windows 2003 domain, with XP clients, we have started seeing routes appearing in the routing tables on both the servers and the clients. The route is a /32 for another computer on the domain. The route gets added when one windows computer connects to another computer and needs to authenticate. For example, if computer A with ip 10.0.1.5/24 browses the c: drive of computer B with ip 10.0.2.5/24, a static route will get added on computer B like so: dest netmask gateway interface 10.0.1.5 255.255.255.255 10.0.2.1 10.0.2.5 This also happens on windows authenticated SQL server connections. It does not happen when computers A and B are on the same subnet. None of the servers have RIP or any other routing protocols enabled, and there are no batch files etc setting routes automatically. There is another windows domain that we manage with a near identical configuration that is not exhibiting this behaviour. The only difference with this domain is that it is not up to date with its patches. Is this meant to be happening? Has anyone else seen this? Why is it needed when I have perfectly good default gateways set on all the computers on the domain?!

  Read the article

• IPSec Tunnel to Amazon EC2 - Netkey, NAT, and routing problem

  - by Ernest Mueller

  Hey all, I'm working on getting an IPSec VPN working between Amazon EC2 and my on-premise. The goal is to be able to safely administer stuff, up/download data, etc. over that tunnel. I have gotten the tunnel up in openswan between a Fedora 12 instance with an elastic IP and a Cisco router that's also NATted. I think the ipsec part is OK, but I'm having trouble figuring out how to route traffic that way; there's no "ipsec0" virutal interface because on Amazon you have to use netkey and not KLIPS for the vpn. I hear iptables may be required and I'm an iptables noob. On the left (Amazon), I have a 10. network. Box 1 is privately 10.254.110.A, publically IP 184.73.168.B. Netkey tunnel is up. Box 2 is publically 130.164.26.C, privately 130.164.0.D And my .conf is: conn ni type= tunnel authby= secret left= 10.254.110.A leftid= 184.73.168.B leftnexthop= %defaultroute leftsubnet= 10.254.0.0/32 right= 130.164.26.C rightid= 130.164.0.D rightnexthop= %defaultroute rightsubnet= 130.164.0.0/18 keyexchange= ike pfs= no auto= start keyingtries= 3 disablearrivalcheck=no ikelifetime= 240m auth= esp compress= no keylife= 60m forceencaps= yes esp= 3des-md5 I added a route to box 1 (130.164.0.0/18 via 10.254.110.A dev eth0) but that doesn't do it for predictable reasons, when I traceroute the traffic's still going "around" and not through the vpn. Routing table: 10.254.110.0/23 dev eth0 proto kernel scope link src 10.254.110.A 130.164.0.0/18 via 10.254.110.178 dev eth0 src 10.254.110.A 169.254.0.0/16 dev eth0 scope link metric 1002 Anyone know how to do the routing with a netkey ipsec tunnel where both sides are NATted? Thanks...

  Read the article

• Valid IP address but can't surf without rebooting

  - by Kat

  I periodically lose internet and router connection at home. When this happens, others are using the router just fine. I am connecting directly through a wired connection to a Belkin router. I can release and renew the IP (and the IP addresses change to 0.0.0.0 and to an IP in my router's range beginning with 192.168.2. as they should) but still can't surf, can't access the router interface. Cycling the router doesn't help, and again, others are able to access the router fine at this time. Only rebooting the computer resolves the issue, and everything is wonderful for a few hours- and then I lose connection again. I have several ideas where to go from here, but I'd like to get some advice first. (Using Windows XP SP3, hardwired connection) Update As stated in the originally, releasing and renewing doesn't solve the issue. However, I have an update. I can ping localhost and my router IP with no problem at all when the issue occurs. However, repairing the network connection does not help. I AM able to get back on by disabling and then re-enabling the network connection in XP. What does that tell us?

  Read the article

• SLI Video Cards

  - by Scott

  I'm configuring a new desktop. I'm looking through all PCI Express 2.0 x16 video cards on NewEgg at the moment. All cards seem to be stating that they have SLI Support or CrossFireX support. I know that these 2 technologies enable you to connect more than one video card together to create more of a powerful video experience. These cards that have this support seem to be more expensive that other cards though. When I did a NewEgg search for cards that did NOT have these two supports, no matches came up for PCI Express 2.0 x16 (haven't checked other interfaces yet though). Can you run an SLI/CrossFireX card as a single card (and if you can is it efficient or even good?), or do you need to have more than one card to run them? Also, do they make cards without these two technologies anymore, and are they even cheaper at this point? I really have no need for SLI/CrossFireX at all, so I was wondering what I should look into. Do cards without this technology not run on the PCI Express 2.0 x16 interface? Thanks ahead of time for all your help.

  Read the article

• SLI Video Cards

  - by Scott

  I'm configuring a new desktop. I'm looking through all PCI Express 2.0 x16 video cards on NewEgg at the moment. All cards seem to be stating that they have SLI Support or CrossFireX support. I know that these 2 technologies enable you to connect more than one video card together to create more of a powerful video experience. These cards that have this support seem to be more expensive that other cards though. When I did a NewEgg search for cards that did NOT have these two supports, no matches came up for PCI Express 2.0 x16 (haven't checked other interfaces yet though). Can you run an SLI/CrossFireX card as a single card (and if you can is it efficient or even good?), or do you need to have more than one card to run them? Also, do they make cards without these two technologies anymore, and are they even cheaper at this point? I really have no need for SLI/CrossFireX at all, so I was wondering what I should look into. Do cards without this technology not run on the PCI Express 2.0 x16 interface? Thanks ahead of time for all your help.

  Read the article

• Using modem for sending voice recording

  - by ircmaxell

  I've got an interesting one for you. I've been going over my server monitoring and notification systems (Nagios based), and realized that if our internet connection goes down, there's no way for it to notify me. I already have a modem listening (Via CentOS 5) on a spare POTS line so that I can dial-in in case our internet goes down. I was wondering if I could come up with a script (Shell, Python, etc) that can dial out and play a recorded message (wave file I'm guessing) when it's picked up. I know Windows supports voice calls over a voice modem, I was wondering if a solution existed for Linux... I know asterisk can probably do it, but isn't that overkill (A full blown VOIP system just for a notification mechanism that will hopefully never be used)? And wouldn't it interfere with the modem's primary function as a backup network interface (PPP spawned via mgetty)? I've done some searching, and haven't really come up with much. I know how to dial out from the command line, but only as a modem (not as voice). Worst case, I could set it up to dial out as a modem, and then just realize that if I get a call with modem sounds from that number that it's the notification... Any insight would be appreciated...

  Read the article

• Migrating to CF9: trouble getting JRun working with SSL

  - by DaveBurns

  I have a client on MX7 who wants to migrate to CF9. I have a dev environment for them on my WinXP machine where I've configured MX7 to run with JRun's built-in web server. I've had that working for a long time with both regular and SSL connections. I installed CF9 yesterday side-by-side with the existing MX7 install to start testing. The install was smooth and detected MX7, adjusted CF9's port numbers for no conflict, etc. Testing started well: MX7 over regular and SSL still worked and CF9 worked over regular HTTP. But I can't get CF9 to work with SSL. I installed a new certificate with keytool, FireFox (v3.6) complained about it being unsigned, I added it to the exception list, and now I get this: Secure Connection Failed An error occurred during a connection to localhost:9101. Peer reports it experienced an internal error. (Error code: ssl_error_internal_error_alert) I've been Googling that in all variations but can't find much help to get past this. I don't see any info in any log files either. FWIW, here's my SSL config from SERVER-INF/jrun.xml: <service class="jrun.servlet.http.SSLService" name="SSLService"> <attribute name="enabled">true</attribute>` <attribute name="interface">*</attribute> <attribute name="port">9101</attribute> <attribute name="keyStore">{jrun.rootdir}/lib/mykey</attribute> <attribute name="keyStorePassword">*deleted*</attribute> <attribute name="trustStore">{jrun.rootdir}/lib/trustStore</attribute> <attribute name="socketFactoryName">jrun.servlet.http.JRunSSLServerSocketFactory</attribute> <attribute name="deactivated">false</attribute> <attribute name="bindAddress">*</attribute> <attribute name="clientAuth">false</attribute> </service> Anyone here know of any issues re setting up SSL and CF9? Anyone had success with it? Dave

  Read the article

• How to subnet hosted VMs

  - by bwizzy

  I have a network of VMs each having a LAN IP address and a public IP address. They each have a 1:1 NAT map for public access via the public IP for HTTP, SSH etc. I'm trying to figure out a way to restrict the LAN IPs from talking to each other, but there are some cases where a group of LAN IPs will need to communicate. I'm using pfSense as a firewall / router on a 192.168.0.0/24 configuration. It seems like I could assign each VM it's own subnet and add a static route to the firewall for that VM to get back to the firewall for internet access / other fw rules. Is that right? I assigned 1 VM with: address 192.168.1.2 netmask 255.255.255.254 gateway 192.168.1.1 Then added a static route on the FW's LAN interface using 192.168.1.0/30 as the destination network and 192.168.1.1 as the gateway. Nothing appears to be working, anyone have any ideas? Please be aware I'm not that familiar with subnets. Thanks!

  Read the article

• Change OpenVZ route to pass through ip failover

  - by Kevin Campion

  I have one dedicaced server with its own IP and another IP (failover) who refer to the first. I will wish to change the gateway of a Proxmox virtual machine (openvz) who runs on this dedicaced server to go through the failover IP rather than the ip of host main server. Once connected to a virtual machine, when I do a traceroute VE# traceroute www.google.fr traceroute to www.google.fr (209.85.229.104), 30 hops max, 60 byte packets 1 MY_SERVER_NAME.ovh.net (xxx.xxx.xxx.xxx FIRST_IP_MAIN_SERVER) 0.021 ms 0.010 ms 0.009 ms The first line tells me the ip of host main server. I would like that the traceroute display the second IP failover. VE# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 * 255.255.255.255 UH 0 0 0 venet0 default 192.0.2.1 0.0.0.0 UG 0 0 0 venet0 With iptables HOST# iptables -t nat -L Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- anywhere anywhere MASQUERADE all -- anywhere anywhere SNAT tcp -- anywhere 10.10.101.2 tcp dpt:www state NEW,RELATED,ESTABLISHED,UNTRACKED to:SECOND_IP_FAILOVER SNAT all -- 10.10.101.2 anywhere to:SECOND_IP_FAILOVER 10.10.101.2 is the virtual machine IP (interface venet0) Any ideas ?

  Read the article

• Error while installing boost_1_54

  - by Farhat

  On trying to install boost I get this error during configuration checks. Googling did not give any pointers. [root@heracles boost_1_54_0]# ./b2 install Performing configuration checks - 32-bit : no (cached) - 64-bit : yes (cached) - arm : no (cached) - mips1 : no (cached) - power : no (cached) - sparc : no (cached) - x86 : yes (cached) error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - has_icu builds : no (cached) warning: Graph library does not contain MPI-based parallel components. note: to enable them, add "using mpi ;" to your user-config.jam - zlib : yes (cached) - iconv (libc) : yes (cached) - icu : no (cached) - icu (lib64) : no (cached) - compiler-supports-ssse3 : yes (cached) - compiler-supports-avx2 : no (cached) - gcc visibility : yes (cached) - long double support : yes (cached) warning: skipping optional Message Passing Interface (MPI) library. note: to enable MPI support, add "using mpi ;" to user-config.jam. note: to suppress this message, pass "--without-mpi" to bjam. note: otherwise, you can safely ignore this message. error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - zlib : yes (cached) How can the alternative for allocator sources be located? Thanks.

  Read the article

• Network problems with Ubuntu on VMware

  - by svick

  I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

  Read the article

• tap interfaces always disabled in linux bridge

  - by Dani Camps

  I have a physical interface eth0, and I want to create two virtual interfaces and bridge them with eth0. For this purpose I do: #Create the virtual interfaces tunctl -t tap0 tunctl -t tap1 ifconfig tap0 up ifconfig tap1 up #Create the bridge brctl addbr br0 brctl stp br0 off brctl addif br0 eth0 brctl addif br0 tap0 brctl addif br0 tap1 #Turning up the bridge ifconfig br0 up However my problem if that the tap interfaces always appear disabled in the bridge, and no traffic flows to them. $brctl show br0 bridge name bridge id STP enabled interfaces br0 8000.080027cabeba no eth2 tap0 tap1 $brctl showstp br0 br0 bridge id 8000.080027cabeba designated root 8000.080027cabeba root port 0 path cost 0 max age 20.00 bridge max age 20.00 hello time 2.00 bridge hello time 2.00 forward delay 15.00 bridge forward delay 15.00 ageing time 300.01 hello timer 0.00 tcn timer 0.00 topology change timer 0.00 gc timer 298.42 flags eth2 (1) port id 8001 state forwarding designated root 8000.080027cabeba path cost 4 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8001 forward delay timer 12.97 designated cost 0 hold timer 1.24 flags tap0 (2) port id 8002 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8002 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags tap1 (3) port id 8003 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8003 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags Is there any way to set the tap interfaces in forwarding state? I do not understand why they are not because STP is disabled. Cheers Daniel

  Read the article

• Debian DNSSEC - howto secure a domain?

  - by Daniel Marschall

  I have a beginner question about DNSSEC. I have much experience with TLS and cryptography-stuff and would like to try out this new technology. I have googled very much about this but I haven't found useful information for me. I think one confusion in information gathering is that "Debian howto DNSSEC setup" can mean "How to USE DNSSEC for resolving" OR "How to secure your domain with DNSSEC". I am searching the second. I am running a Debian Squeeze server with root privileges which has a domain name ending with ".de" (which is already signed by the root zone). The network interface at this server uses the gateway IP (DNS resolver?) of the datacentre the server is running on. My domain is hosted at freedns.afraid.org , where I can add DNS RRs for my domain. They are currently NOT capable of adding DNSSEC RRs, but I am bugging them to support this soon. ;-) My simple question is: How do I setup DNSSEC on Debian? Resp. who have I ask to? As far as I understand, all I have to do is to run dnssec-keygen on my Debian server and then add the key to my DNS-provider as DNSSEC RR. (And change it every 30 days?) I have looked at this http://www.isc.org/files/DNSSEC_in_6_minutes.pdf but it looks like you have to be the owner of a ZONE, so I don't think this applies to me. Who needs to sign my domain? My DNS-provider or my zone (DeNIC) or can I do it myself? Any help is very appreciated!

  Read the article

• No audio in my ubuntu system

  - by hap497

  Hi, I am running ubuntu 9.10. But there is no sound in my environment. When I go to System-Preference, there is no 'sound' entry there. $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: I82801AAICH [Intel 82801AA-ICH], device 0: Intel ICH [Intel 82801AA-ICH] Subdevices: 1/1 Subdevice #0: subdevice #0 $ lsmod Module Size Used by usb_storage 52576 3 binfmt_misc 8356 1 vboxvfs 34620 0 vboxvideo 1884 1 drm 159584 2 vboxvideo agpgart 34988 1 drm snd_intel8x0 30168 2 snd_ac97_codec 101216 1 snd_intel8x0 ac97_bus 1532 1 snd_ac97_codec snd_pcm_oss 37920 0 snd_mixer_oss 16028 1 snd_pcm_oss snd_pcm 75296 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_seq_dummy 2656 0 snd_seq_oss 28576 0 iptable_filter 3100 0 snd_seq_midi 6432 0 ip_tables 11692 1 iptable_filter x_tables 16544 1 ip_tables snd_rawmidi 22208 1 snd_seq_midi snd_seq_midi_event 6940 2 snd_seq_oss,snd_seq_midi ppdev 6688 0 snd_seq 50224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event snd_timer 22276 2 snd_pcm,snd_seq snd_seq_device 6920 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq psmouse 56500 0 serio_raw 5280 0 snd 59204 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_ oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_ti mer,snd_seq_device i2c_piix4 9932 0 parport_pc 31940 0 soundcore 7264 1 snd snd_page_alloc 9156 2 snd_intel8x0,snd_pcm vboxguest 143836 7 vboxvfs lp 8964 0 parport 35340 3 ppdev,parport_pc,lp pcnet32 32644 0 mii 5212 1 pcnet32 floppy 54916 0 ~:987:2$ lspci 00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02) 00:01.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] 00:01.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter 00:03.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 40) 00:04.0 System peripheral: InnoTek Systemberatung GmbH VirtualBox Guest Service 00:05.0 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio Controller (rev 01) 00:06.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB 00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 0 00:0b.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller ~:988:3$

  Read the article

• Solaris 10: cannot ping to/from server

  - by anurag kohli

  All, I have a Solaris 10 server which is not reachable by IP (ie can't ping to/from the server). I believe I have the default route setup correctly. See below: # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 192.168.62.100 netmask ffffff00 broadcast 192.168.62.255 ether 0:14:4f:b1:9b:30 # netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface -------------------- -------------------- ----- ----- ------ --------- 192.168.62.0 192.168.62.100 U 1 40 bge0 224.0.0.0 192.168.62.100 U 1 0 bge0 default 192.168.62.1 UG 1 0 127.0.0.1 127.0.0.1 UH 1 4 lo0 # # cat /etc/defaultrouter 192.168.62.1 I have verified layer1 and layer 2 are up on the switchport, and that it's on the correct VLAN. I have also checked the default gateawy (192.168.62.1) is in fact reachable since I can ping it from my PC: Pinging 192.168.62.1 with 32 bytes of data: Reply from 192.168.62.1: bytes=32 time=1ms TTL=254 Reply from 192.168.62.1: bytes=32 time=1ms TTL=254 Reply from 192.168.62.1: bytes=32 time=3ms TTL=254 Reply from 192.168.62.1: bytes=32 time=6ms TTL=254 I'm at a loss as to what is wrong. I would highly appreciated your assistance. Thank you very much.

  Read the article

• Does NetworkSolutions have a good DNS service?

  - by joxl

  I'm recovering from a DNS disaster and I need some good advice on an alternate solution. My company owns a domain name through NetworkSolutions. Our website is hosted by another company who also maintains our DNS records. Our email is hosted by Google Apps, and the MX records are maintained through the afore-mentioned website/DNS host. Yesterday our website/DNS host had a serious hiccup in some software and completely overwrote all of our DNS records with invalid values; successfully pointing our domain and MX records at the wrong servers. Unfortunately it wasn't caught until it had time to significantly propagate. On top of that, it wasn't fixed until several hours later, combine that with a long TTL on the records; we have customers who are still bouncing emails. Anyhow, I am now completely terrified of this company's ability to do a good job, so I am considering switching to NetworkSolutions for our DNS service. I need the ability to configure A, CNAME, MX, and TXT records, preferably with a nice user interface (our current provider has a poor UI and doesn't support TXT records). Is NetworkSolutions a recommended DNS host? I am a little biased in their direction because the service will be free since we already pay them for our domain name. However I'm curious what others have experienced with their service.

  Read the article

• Storing changes to multiple databases in a single centralized database

  - by B4x

  The setup: multiple MySQL databases at different locations with the same scheme. The databases are in production. The motivation: we want to present information in these databases in a web interface, clearly showing which database the row originated from. We want to be able to get this data from one single source (for different reasons, one of them is pagination which gets tricky if you use multiple sources). The problem: how do we collect data from multiple databases, storing it at a central location and clearly marking the origin of each row? We have discussed using a centralized DB that tracks changes to the production DBs, with the same schema and one additional column for origin. If possible, we would like to avoid having to make changes in the production environment. Since we can't use MySQL's replication (multiple masters to a single slave isn't allowed), what are our other options? Are there any existing solutions for something like this or do we have to code something ourselves? Is the best solution to change the database schemas in production and add a column for origin? The idea of a centralized database isn't set in stone. If there is a solution to this that solves our other problems without a centralized DB, we can be flexible. Any help is much appreciated.

  Read the article

• Cisco ASA dropping IPsec VPN between istself and CentOS server

  - by sebelk

  Currently we're trying to set up an IPsec VPN between a Cisco ASA Version 8.0(4) and a CentOS Linux server. The tunnel comes up successfully, but for some reason that we can't figure out, the firewall is dropping packets from the VPN. The IPsec settings in the ASA sre as follows: crypto ipsec transform-set up-transform-set esp-3des esp-md5-hmac crypto ipsec transform-set up-transform-set2 esp-3des esp-sha-hmac crypto ipsec transform-set up-transform-set3 esp-aes esp-md5-hmac crypto ipsec transform-set up-transform-set4 esp-aes esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map linuxserver 10 match address filtro-encrypt-linuxserver crypto map linuxserver 10 set peer linuxserver crypto map linuxserver 10 set transform-set up-transform-set2 up-transform-set3 up-transform-set4 crypto map linuxserver 10 set security-association lifetime seconds 28800 crypto map linuxserver 10 set security-association lifetime kilobytes 4608000 crypto map linuxserver interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes hash sha group 2 lifetime 28800 crypto isakmp policy 2 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 3 authentication pre-share encryption aes-256 hash md5 group 2 lifetime 86400 crypto isakmp policy 4 authentication pre-share encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 5 authentication pre-share encryption aes-192 hash md5 group 2 group-policy linuxserverip internal group-policy linuxserverip attributes vpn-filter value filtro-linuxserverip tunnel-group linuxserverip type ipsec-l2l tunnel-group linuxserverip general-attributes default-group-policy linuxserverip tunnel-group linuxserverip ipsec-attributes pre-shared-key * Does anyone know where the problem is and how to fix it?

  Read the article

• Installing Joomla on Windows Server 2008 with IIS 7.0

  - by Greg Zwaagstra

  Hi, I have been spending the past while trying to install Joomla on a server running Windows Server 2008. I have successfully installed PHP (using Microsoft's web tool for installing PHP with IIS) and MySQL and am now trying to run the browser-based installation. Everything comes up green, I fill in the appropriate information regarding the site name, MySQL information, etc. and no errors are thrown. However, when I get to the step that asks me to remove the installation directory, I am unable to do so as Windows states it is in use by another program (I cannot fathom how this is true). Also, there is no configuration.php file that is created so if I were to manage to delete this folder I have a feeling that there would be problems. I was thinking there was some kind of a permissions issue and have set the permissions for IIS_IUSRS to have read, write, and execute permissions for the entire folder that Joomla resides in but this has not helped. Any help in this matter is greatly appreciated. ;) Greg EDIT: I decided to try and manually install Joomla by manually editing the configuration.php file. This has worked great and now I am certain there is some kind of a permissions issue going on because I am able to do everything that involves the MySQL database (create an article, edit menu items, etc.), but anything that involves making changes to Joomla installation's directory does not work (install plugins, edit configuration settings using the Global Configuration menu within Joomla, etc.) I have granted IIS_IUSRS every permission except Full Control (reading on the Joomla! forums shows that this should be enough for everything to work). This is confusing to me and I am quite stuck on this problem. EDIT 2: The bizarre thing is that in the System Info under Directory Permissions, everything turns up as Writable but then whenever I try to actually use Joomla to, for example, edit the configuration.php file using the interface, it says it is unable to edit the file.

  Read the article

• Automate creation of Windows startup script?

  - by Niten

  Is there a good way to automate installing local startup (rather than login) scripts in Windows XP and Windows 7, via the command line, WMI, or otherwise (even COM or Win32 if it comes to that)? I need to setup a local startup script on a large number of computers, and unfortunately, Active Directory is absolutely not an option. I would like to write a script or small program that I can run on each computer to perform the startup script installation in order to save myself a lot of error-prone point-and-click manual labor. I see that when one uses gpedit.msc to create a local startup script, information about the script gets stored in the registry here: HKLM\Software\Policies\Microsoft\Windows\System\Scripts\Startup However, if you create such a script and then delete its registry key, the script will remain listed in the local Group Policy editor; as is so often the case in Windows, apparently there is more going on there than meets the eye. This leads me to question whether it's safe to manually add subkeys for new startup scripts here (I wouldn't want my script to be overwritten by later changes made using the local Group Policy editor, for instance)... Another option that's occurred to me is to create an item in the Task Scheduler configured to run at system startup. However, my concerns there are twofold: Can this be automated any more easily? For instance, the at command doesn't appear to let you schedule a task for system startup, and WMI's Win32_ScheduledJob interface looks unreliable (it fails to show any of my currently scheduled tasks, for one thing). Would I be able to prevent users from logging in until the scheduled startup task is completed, as can be done with "normal" Windows startup scripts? Thanks in advance for any suggestions, I've been banging my head against this one for a bit...

  Read the article

• Cannot browse remote networks even with WINS configured

  - by paradroid

  As the NetBIOS protocol acts on Layer 2 and so is not routable, In order to enable network browsing of remote networks, WINS has been installed and configured on two domain controllers, both of which are on different networks. The WINS servers seem to be replicating with eachother, and each has 127.0.0.1 set as the Primary WINS Server in each of their LAN interface properties, with nothing entered for Secondary WINS Server. The DC which holds the PDC Emulator FSMO role has the Computer Browser service running and set to Auto start, and it has the WINS/NBT node type network setting at 0x8 (H-node - Hybrid node). Remote network browsing does not work. Is the WINS/NBT node type correct for this scenario? The reason why I think it may not be the right one is because I set the DHCP Server's 046 WINS/NBT node type option to 0x8 as well, after which the DHCP clients started to disappear from the Network folders. When that option is not set, does it default to B-node (Broadcast node)? Or could it be a problem with the WINS servers setup?

  Read the article

• Ubuntu second static IP, ifconfig, /etc/network/interfaces

  - by Schmoove

  I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

  Read the article

• (Zywall USG 300) NAT bypassed when accessing in-house-server From LAN Via domain name

  - by mschr

  My situations is like this; i host a number of websites from within our joint network solution. On the network is basically 3 categories: the known public, registered via mac, given static dhcp lease the anonymous lan connections, given lease from specific dhcp range switches, unix hosts firewall Now, consider following hosts which are of interest 111.111.111.111 (Zywall USG 300 WAN) 192.168.1.1 (ZyWall USG 300 LAN) load balances and bw monitors plus handles NAT 192.168.1.2 (Linux www) serves mydomain1.tld and mydomain2.tld 192.168.123.123 (Random LAN client) accesses mydomain1.tld from LAN 23.234.12.253 (Random External client) accesses mydomain1.tld via WAN DNS A records are setup so that both mydomain1.tld and mydomain2.tld points to 111.111.111.111 - and the Linux www serves the http parts with VirtualHost configurations, setting up the document roots pr ServerName, this is not so interesting though.. NAT rule translates 111.111.111.111:80 to 192.168.1.2:80 (1:1 NAT) Our problem follows; When accessing http://mydomain1.tld from outside (23.234.12.253 example host) the joint network - everything is fine, zywall receives requests via port 80 and maps it to the linux host' httpd. However - once trying to go through the NAT from LAN side (in-house, 192.168.123.123 example host) then one gets filtered in the Zywall port 80 firewall. I know this only because port 443 is open for administration interface and https://mydomain1.tld prompts for zywall login. So my conclusion is, that the LAN that accesses 111.111.111.111 in fact are routed to 192.168.1.1 whilst bypassing the NAT table. I need to know how to setup NAT / Policy Route, so that LAN WAN LAN will function with proper network translations instead of doing the 'quick nameserver lookup' or whatever this might be.

  Read the article

< Previous Page | 414 415 416 417 418 419 420 421 422 423 424 425  | Next Page >