Search Results

Search found 12472 results on 499 pages for 'remote debugging'.

Page 415/499 | < Previous Page | 411 412 413 414 415 416 417 418 419 420 421 422  | Next Page >

• TeamCity EC2 Integration via ISA Server

  - by Tim Long

  I have a TeamCity server which is actually installed on SBS 2003 Premium with ISA Server (firewall/proxy) installed. My ADSL connection has multiple IP addresses, which all resolve directly to my SBS external NIC. The NIC is therefore multi-homed and I have allocated one of the IP addresses specifically to TeamCity. In ISA, I've created an access rule to allow the traffic in. I can access my TeamCity server externally and view the web interface, that all works fine. I want to use the Amazon EC2 integration in TeamCity to launch build agents 'in the cloud'. The problem I am having is that when the agent starts, it sees the server and registers, then just sits there waiting. On the server side, the agent appears as 'disconnected'. Examining the settings, the agent's IP address appears to be that of the external NIC. What I think might be happening is that the traffic is undergoing Network Address Translation (NAT) so that TeamCity always thinks the agent is locally installed and therefore can't communicate with the actual remote agent. This seems to happen even though I have a permanent static IP address dedicated to TeamCity. So, the question is this. How can I make traffic to a specific IP address pass through the ISA server un-NATted?

  Read the article

• Same domain only : smtp; 5.1.0 - Unknown address error 530-'SMTP authentication is required

  - by user124672

  I have a very strange problem after moving my netwave.be domain from WebHost4Life to Arvixe. I configured several email adresses, like [email protected] and [email protected]. For POP3 I can use mail.netwave.be, a mailserver hosted by Arvixe. However, for SMTP I have to use relay.skynet.be. Skynet (Belgacom) is one of the biggest internet providers in Belgium and blocks smtp requests to external mailservers. So for years I've been using relay.skynet.be to send my messages using [email protected] as the sender. The worked perfectly. After moving my domain to Arvixe, this is no longer the case. I can send emails to people, no problem. I have received emails too, so I suspect that's ok too. But I can't send emails from one user of my domain to another user. For example, if I send a mail from [email protected] to [email protected], relay.skynet.be picks up the mail just fine. A few seconds later, I get a 'Delivery Status Notification (Failure)' mail that contains: Reporting-MTA: dns; mailrelay012.isp.belgacom.be Final-Recipient: rfc822;[email protected] Action: failed Status: 5.0.0 (permanent failure) Remote-MTA: dns; [69.72.141.4] Diagnostic-Code: smtp; 5.1.0 - Unknown address error 530-'SMTP authentication is required.' (delivery attempts: 0) Like I said, this only seems to be the case when both the sender and recipient are adresses of a domain hosted by Arvixe. I have serveral accounts not related to Arvixe at all. I can use relay.skynet.be to send mail to [email protected] using these accounts. Likewise, I can use relay.skynet.be to send mail from [email protected] to these accounts. but not from one Arvixe account to another. I hope I have clearly outlined the problem and someone will be able to help me.

  Read the article

• KVM recommendations

  - by alex

  I recently tried out a cheaper KVM solution, a dual monitor one with a USB hub and audio/mic support. It seemed the perfect KVM. However, these are my experiences. When using my keyboard via the PS/2 connection, none of my multimedia keys work (useful, because it has a volume control and my speakers do not, only on a wireless remote control.) I plugged the keyboard in via the USB port - and it seemed to work. However, I believe to switch the hub from PC to Mac, you need to use a keyboard combo, which is only supported when the keyboard is plugged in via PS/2 Sometimes the middle mouse button doesn't work when connected via PS/2. The multi monitor is VGA - I just found out by the looks of things my Mac Mini outputs DVI Digital only (though this is my fault!). Mac works with 2 screens, but switching and switching back can cause it not to display on the 2nd screen unless I go detect displays again. My question is - is there a KVM out there that supports these features? USB keyboard and mouse inputs will full multimedia keys support Dual monitor DVI connections Hotkey to change PCs and physical button USB hub Emulate screens attached when switching to a different computer Works with PC and Mac Audio / Microphone support Does one exist, that won't cost the world? So far the only one that seems to support all this (that I can tell) is this one. UPDATE I ended up buying the Aten CS1642. It's expensive, but it seems to work great!

  Read the article

• ClearOS - how to create a site to site VPN between two ClearOS boxes?

  - by Scott Szretter

  I plan on setting up some ClearOS boxes at several sites, and would like to set up site-to-site VPN between the remote sites and a main site (all running ClearOS enterprise 5.2sp1 / latest version). I have found references for how to set up ClearOS to VPN in to devices such as cisco for IPSEC, and others with PPTP. But for these methods it did not mention how you might configure 2 ClearOS boxes to talk to each other ipsec or pptp. I also saw documentation on installing OpenVPN and using the OpenVPN client software to VPN in to the ClearOS box. I will probably use this for individual users to VPN in, but I have some small sites ( 1 to 10 users) that will have their own ClearOS box and need to create a site to site VPN link back to the main site's OpenVPN box. Is this possible, can you point me to docs, or other info or basically, how? A couple updates: I did find a thread that asks the same basic question, where the user has a vpn set up between the two clearos machines (after installing ipsec vpn modules), just not transporting traffic between the LANS - and the very last post claims you have to edit some files (/etc/ipsec.conf) and set leftnexthop rightnexthop values to %direct. After that, it's supposed to work. Could it be that simple? I also posted to clear foundation, and they pointed me to some documentation for setting up ipsec unmanaged vpn. This looks pretty good, but, I will most likely need to figure out how to handle a dynamic dns type setup at least on one end. Also, what does it mean by multi-wan? Finally, what happens when a vpn connection goes down exactly - someone has to reboot the box or ?

  Read the article

• Route specific HTTP requests through pfSense OpenVPN

  - by DennisQ

  Hi, to start, I have very little knowledge on routes, iptables, etc. That said, here's what I'm trying to accomplish and where I think I'm stumped: Problem: We have an external website which we recently firewalled so it only accepts traffic from our office IP addresses. This works well at the office, but doesn't work for remote access through VPN as we don't route all traffic through OpenVPN. I would rather avoid forcing everyone to route all traffic through just to accommodate this one site. Environment: Main router box is running pfSense. Em0 is internal IP, Em1 is external. Internal net is 10.23.x and VPN is 10.0.8.0/24 I believe what I need to do is add a route to the VPN server config to send all traffic to that IP over the VPN tunnel. I think that part's working, but I don't get a response back, so I'm assuming that I need some NAT config on the VPN server to route the response back over the tunnel? What I've found so far is to try the following, but since this is a pfSense box on FreeBSD, I can't run iptables, etc. Make sure ip forwarding is enabled: echo 1 /proc/sys/net/ipv4/ip_forward Setup NAT back out: iptables -t nat -A POSTROUTING -s 10.0.8.0/24 -o em0 -j MASQUERADE Am I on the right path, and if so how do I accomplish this through pfSense UI or FreeBSD CLI? Thanks!

  Read the article

• Reverse SSH Tunnel

  - by chris

  I am trying to forward web traffic from a remote server to my local machine in order to test out some API integration (tropo, paypal, etc). Basically, I'm trying to setup something similar to what tunnlr.com provides. I've initiated the ssh tunnel with the command $ssh –nNT –R :7777:localhost:5000 user@server Then I can see that server has is now listening on port 7777 with user@server:$netstat -ant | grep 7777 tcp 0 0 127.0.0.1:7777 0.0.0.0:* LISTEN tcp6 0 0 ::1:7777 :::* LISTEN $user@server:curl localhost:7777 Hello from local machine So that works fine. The curl request is actually served from the local machine. Now, how do I enable server.com:8888 to be routed through that tunnel? I've tried using nginx like so: upstream tunnel { server 0.0.0.0:7777; } server { listen 8888; server_name server.com; location / { access_log /var/log/nginx/tunnel-access.log; error_log /var/log/nginx/tunnel-error.log; proxy_pass http://tunnel; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } } From the nginx error log I see: [error] 11389#0: *1 connect() failed (111: Connection refused) I've been looking at trying to use iptables, but haven't made any progress. iptables seems like a more elegant solution than running nginx just for tunneling. Any help is greatly appreciated. Thanks!

  Read the article

• Reverse Proxies and AJAX

  - by osij2is

  A client of ours is using IBM/Tivoli WebSEAL, a reverse-proxy server for some of their internal users. Our web application (ASP.NET 2.0) and is a fairly straightforward web/database application. Currently, our client users that are going through the WebSEAL proxy are having problems with a .NET 3rd party control. Users who are not going through the proxy have no issues. The 3rd party control is nothing more than an AJAX dynamic tree that on each click requests all the nodes for each leaf. Now our clients claim that once users click on a node in the control, the control itself freezes in such a way that they don't see anything populate. Users see "Loading..." message appear but no new activity there afterwards. They have to leave the page and go back to the original page in order to view the new nodes. I've never worked with a reverse proxy before so I have googled quite a bit on the subject even found an article on SF. IBM/Tivoli has mentioned this issue before but this is about all they mention at all. While the IBM doc is very helpful, all of our AJAX is from the 3rd party control. I've tried troubleshooting using Firebug but by not being behind the reverse proxy, I'm unable to truly replicate the problem. My question is: does anyone have experience with reverse proxies and issues with AJAX sites? How can I go about proving what the exact issue is? Currently we're negotiating remote access so assume for the greater part that I will have access to a machine that's using the WebSEAL proxy. P.S. I realize this question might teeter on the StackOverFlow/ServerFault jurisdictional debate, but I'm trying to investigate from the systems perspective. I have no experience with reverse proxies (and I'm unclear on the benefits) and little with forwarding proxies.

  Read the article

• Get-ChildItem fails to connect in SQLSERVER drive

  - by Norman Kelm

  I'm having some trouble with the SQLSERVER PSDRIVE. See error below. I only have named instances on my PC, both 2005 and 2008 Added the SQL snapins. The PC is named YODA The SQL instance is SQL2008 Navigate to the Databases folder for YODA\SQL2008. You can see the path below. dir -name spits out a connection error trying to connect to YODASQL2008\DEFAULT when it should be trying to connect to YODA\SQL2008. Then it outputs the db name which is Twitter in this case. Is there something missing from my config? Output: PS SQLSERVER:\SQL\YODA\SQL2008\Databases dir -name Get-ChildItem : SQL Server PowerShell provider error: Could not connect to 'YODASQL2008\DEFAULT'. [Failed to connect to server YODASQL2008. -- A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)] At line:1 char:4 + dir <<<< -name + CategoryInfo : OpenError: (SQLSERVER:\SQL\...tabases\Twitter:SqlPath) [Get-ChildItem], GenericProviderException + FullyQualifiedErrorId : ConnectFailed,Microsoft.PowerShell.Commands.GetChildItemCommand Twitter Repeats with error for every database. Thanks, Norman

  Read the article

• Disabling standby modus on Gear4 Blackbox speakers

  - by cj

  I have a set of bluetooth Gear4 Blackbox speakers. The sound quality and the design is great, but it switches to standby modus automatically every now and then, when I am listening to music and when it's silent. In that situation, the only way to get them working again is turning them off and on, since they do not react to the remote nor to the buttons on top of it. I emailed Gear4 with this problem and they recommended me to reflash the firmware again, but the problem is persisting after having done that. It has nothing to do with the device that is streaming music. So, the question is, is there a way to disable the standby modus permamently, so the speakers are all the time active even if I am not using them? To switch them off I would just turn the power switch off. If anyone is curious about what device I am talking about, here's a link to Amazon, but I wouldn't reccomend anyone to buy them because of this problem. http://www.amazon.co.uk/Gear-4-PG142-GEAR4-BlackBox/dp/B000QEFZI2 Thanks in advance.

  Read the article

• A network-related or instance-specific error occurred while establishing a connection to SQL Server

  - by sf

  Hi, I'm getting the following error when trying to load an Asp.NET MVC App on IIS 7 with Sql Server 2008 Express. The App uses Linq to SQL. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) I've done some searching and all answers point to enabling TCP connections in Sql Server Configuration which I have done to no avail. The connection string I am using is: Server=SERVERNAME\SQLEXPRESS;Database=DBName;Integrated Security=true The catch. I have another app that already could talk to the Sql Server just fine. Even before playing around with the Sql Server Configuration Settings. The other app uses the following connectionstring: Data Source=SERVERNAME\SQLEXPRESS;Initial Catalog=OtherDbName;Integrated Security=True;Persist Security Info=False;Connect Timeout=120 I've tried this connectionstring on the app that isn't working and it still doesn't work. Please help. I think i'm about to go crazy

  Read the article

• Problems setting up a VPN: can connect but can't ping anyone

  - by Fernando

  This is my first time setting a VPN. Clients can connect but can't ping other machines. This is certainly a route problem but i can't find the right way to configure it. Here is a sample example of the two LANS i want to connect: So, i want machines from 192.168.1.0/24 being able to connect with 192.168.0.0/24 as if they were on the same network. For the VPN network, i would like to use the 10.0.0.0/24 range. Here is my server.conf: proto udp port 1194 dev tun server 10.0.0.0 255.255.255.0 push "route 192.168.0.0 255.255.255.0 192.168.0.1" push "dhcp-option DNS 192.168.0.1" push "dhcp-option WINS 192.168.0.1" comp-lzo keepalive 10 120 float max-clients 10 persist-key persist-tun log-append /var/log/openvpn.log verb 6 tls-server dh /etc/openvpn/keys/dh1024.pem ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/server.crt key /etc/openvpn/keys/server.key tls-auth /etc/openvpn/keys/mykey.key 0 status /var/log/openvpn.stats And one of my clients 192.168.1.2: client dev tap proto udp remote my.no-ip.address 1194 route 192.168.1.0 255.0.0.0 192.168.1.1 3 resolv-retry infinite nobind persist-key persist-tun ca "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\ca.crt" cert "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\test1.crt" key "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\test1.key" tls-auth "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\mykey.key" 1 ns-cert-type server cipher BF-CBC comp-lzo verb 1 What exactly i am doing wrong? All machines can connect to openvpn but the ping doesn't work. At the client log i see the following error: Wed Feb 16 09:43:23 2011 OpenVPN ROUTE: OpenVPN needs a gateway parameter for a --route option and no default was specified by either --route-gateway or --ifconfig options Wed Feb 16 09:43:23 2011 OpenVPN ROUTE: failed to parse/resolve route for host/network: 10.0.0.1 Thanks!

  Read the article

• How to run some commands after booting from ArchLinux disk? Or how to change some settings in .iso before booting?

  - by Alexander Ovchinnikov

  How to install Arch Linux with traditional installer with only ssh-access to server? There is nice guide: https://wiki.archlinux.org/index.php/Install_from_SSH I try test this on my home vps: Start VPS with any linux bootable cd and login to remote server (vps) wget http://mirrors.kernel.org/archlinux/iso/latest/archlinux-2010.05-netinstall-x86_64.iso dd if=archlinux-2010.05-netinstall-x86_64.iso of=/dev/sda reboot ... I see, it works but without ssh connection... I need make script, which will send this commands after reboot: aif -p partial-configure-network (and write some information about my server ip etc.) /etc/rc.d/sshd start (need to start sshd) echo "sshd: ALL" /etc/hosts.allow (to allow me login to server, by default deny all) passwd (by default its empty, can't login via ssh with empty password) Can I edit .iso or may be /dev/sda? May be I need write script, which will start after system boot and do this things or may be I can set this settings by default and system will start with correct settings (i think its possible at least in 2. and 3.). Thank you!

  Read the article

• HTTP Error 503 - Service is unavailable (how fix?)

  - by SilverLight

  i have a web site for download mobile files and there many users in my web site. sometimes i have the error below : HTTP Error 503 - Service is unavailable 1-so why this error happens and what is that mean? 2-as i know appache free up itself when it's oveloaded, but what about iis? how can i put some limitations in my server (i have remote access to my server) for prevent this error happening? a.is limitation of dowload's speed efficient for prevent that error's occur? how can i do that? is squid useful for this job or i can do that with another iis extension. b.is limitation of download's Bandwidth efficient for prevent that error's occur? how can i do that (with iis or another extension)? in right side of iis - configure area - i found some limits. what do those limits mean and can i use them for keep my server alive all the time? EDIT: after viewing event viewer of windows - custom views - server rols - web server (iis) i figure out there is no error in that area. but many warnings and information. the latest warnings and information are like below : warning A worker process '2408' serving application pool 'ASP.NET 4.0 (Integrated)' failed to stop a listener channel for protocol 'http' in the allotted time. The data field contains the error number. warning A process serving application pool 'ASP.NET 4.0 (Integrated)' exceeded time limits during shut down. The process id was '6764'. warning A worker process '3232' serving application pool 'ASP.NET 4.0 (Integrated)' failed to stop a listener channel for protocol 'http' in the allotted time. The data field contains the error number. warning A process serving application pool 'ASP.NET 4.0 (Integrated)' exceeded time limits during shut down. The process id was '3928'. thanks in advance best regards

  Read the article

• Modem doesn't seem to pass internet connection to router

  - by Vian Esterhuizen

  I was supplied a Cisco DPC3825 modem by my ISP and use a Cisco E4200 as my main router. Today the Internet just stopped working, just out of the blue, I can't think of anything that would have triggered it. It's been working pretty good for the past month except for a few random blips here and there. After some trouble shooting I realized that a direct wired connection to the modem would get me Internet access but if I was wired to the router as I was before I would have no connection. Assuming it was router I connected a TP-Link WR841N but it had the exact same problem. Also, connecting to the router via Wi-Fi from multiple devices will connect me to the router but I still can't get access to the Internet. From these test, it seems that the modem just won't send Internet through to the router but is clearly connecting and able to directly connect to my PC. What I've Tried A full reset and factory reset on the E4200 A full reset on the modem (but I believe my ISP has remote access to the modem because the passwords and so on are always set back). My ISP has remotely reconfigured the modem What I Should Try What else can I try? What should I do to try to narrow down the issue? Can you figure out what the problem might be based on this information?

  Read the article

• Can't access IIS 7 server URL from the same IIS 7 server.

  - by Kevin Raffay

  We have an intranet site ie, xxx.yyyy.com, that users access by entering "http"://xxx.yyy.com. Our problems started when we migrated to IIS 7 running on a new 2003 server. We got rid of our single-sign on code and implemented a security model where we capture a user's domain credentials which we then authenticate against a DB. In order to get the domain credentials passed to our ASP.NET app, we have the following settings: Anonymous Authentication:Disabled ASP.NET Impersonation: Enabled Basic/Digest/Forms Authentication: Disabled Windows Authentication: Enabled We allow "*" and deny "?" in the web.config. Browsing "http"://xxx.yyy.com from any client PC results in a domain login prompt, and if your enter a proper user/pwd, you can get in. However, browsing "http"://xxx.yyy.com while remoting into the server results in 3 domain login prompts and eventually a 401 error - unauthorized. We have traced this behavior to problems with our web site where we have pages doing "screen scraping" using the HttpRequest calling a url on the same server. When doing a HttpRequest from any other client, using a test harness that passes authorized credentials, all is good. So internal HttpRequest calls on the server fail, just like attempts to browse that server's url from within a remote session. Why would a to "http"://xxx.yyy.com on server xxx.yyy.com fail authentication?

  Read the article

• IIS 7.5 Basic authorization issue

  - by Alsin

  When I log on using correct user name\password (I always copy-paste them) I get 401.1 error. User name and password are correct (user is created on server locally, not a domain one). I can run program as this user (runas /noprofile /user:tmp notepad.exe). Basic authorization's default domain is a server name, realm is empty. I've saved FailedReqLogFile. AUTH_BASIC_LOGON_FAILED shows ErrorCode="Logon failure: unknown user name or bad password. (0x8007052e)" and MODULE_SET_RESPONSE_ERROR_STATUS shows ModuleName="BasicAuthenticationModule", Notification="AUTHENTICATE_REQUEST", HttpStatus="401", HttpReason="Unauthorized", HttpSubStatus="1", ErrorCode="Logon failure: unknown user name or bad password. (0x8007052e)", ConfigExceptionInfo="" And one more thing - if I use my domain login\password it woks! Basic Authentications is only enabled authentication in application... Could you please suggest me how I can troubleshoot and fix this issue? Maybe somebody hit it before... Best regards, Alex UPDATE: I get 401.1 when I trying to access site from local host. I can actually access files from remote host.

  Read the article

• SAN Replication for Fault tolerance using EVA4400

  - by Sergei

  Hi Everyone, I hope that someone would point me in the correct direction - it looks like I have no enough konwledge in the subject and timeframes are too tight for me to explore different scenarios in depth.. We have two datacenters few miles away from each other connected by 100 Mbps link.Each datacenter will have 5 BL490 blades with ESX Standard hosting about 50 VMs. Eac hsite has HP eva4400 SAN with SAN replication set up.VC is going to be in the first datacenter and both datacenter are networked. SAN Replication is block level so it seems like I cannot just replicate changes but all writes would have to be replicated.This should not be a problem as link can sustain about 1.8 TB a dayand data can be buffered. I am having trouble however visioning how recovery would work in this case.We don't need instant recovery , I would say 4 hours recovery time is accepted so fancy automatic SRM like DR scenario would not be easily accepted due to the financial reasons, however any comments are welcomed. Current idea is following: replicate LUNs from primary site to the secondary.When disaster strikes, IT personnel switches on ESX hosts on the remote side and connects replicated LUNS to them, then registers VMs and changes IP address. I understand that this seems like horribly manual process and I almost sure I have missed some obvious pitfalls here. Could someone let me know what direction should I go?An articles regarding the subject? This is a brand new setup and we would rather build up basic recovery process and scale it later.I just need to have a right direction to allow for such scalability. Thank you very much in advance!

  Read the article

• Can't setup 3 nodes MongoDB recplica set

  - by Victor Lin

  I just follow instructions in MongoDB document Replica Sets - Basics to setup a 3-node Replica set. Everything goes fine when I do the initiate and add first node in the primary. [foo@host-a mongodb]$ bin/mongo localhost MongoDB shell version: 1.8.2 connecting to: localhost > rs.initiate() { "info2" : "no configuration explicitly specified -- making one", "info" : "Config now saved locally. Should come online in about a minute.", "ok" : 1 } > rs.add("host-b") { "ok" : 1 } So far so good, but when I try to add third node myset:PRIMARY> rs.addArb("host-c") Sun Aug 7 22:57:09 MessagingPort recv() errno:104 Connection reset by peer 127.0.0.1:27017 Sun Aug 7 22:57:09 SocketException: remote: error: 9001 socket exception [1] Sun Aug 7 22:57:09 DBClientCursor::init call() failed Sun Aug 7 22:57:09 query failed : local.$cmd { count: "system.replset", query: {}, fields: {} } to: 127.0.0.1 Sun Aug 7 22:57:09 Error: error doing query: failed shell/collection.js:150 Sun Aug 7 22:57:09 trying reconnect to 127.0.0.1 Sun Aug 7 22:57:09 reconnect 127.0.0.1 ok As result, the current primary became secondary, and the host-b was marked as dead, but actually, it is still alive. myset:SECONDARY> rs.status() { "set" : "myset", "date" : ISODate("2011-08-08T04:03:23Z"), "myState" : 2, "members" : [ { "_id" : 0, "name" : "host-a:27017", "health" : 1, "state" : 2, "stateStr" : "SECONDARY", "optime" : { "t" : 1312775799000, "i" : 1 }, "optimeDate" : ISODate("2011-08-08T03:56:39Z"), "self" : true }, { "_id" : 1, "name" : "host-b", "health" : 0, "state" : 6, "stateStr" : "(not reachable/healthy)", "uptime" : 0, "optime" : { "t" : 0, "i" : 0 }, "optimeDate" : ISODate("1970-01-01T00:00:00Z"), "lastHeartbeat" : ISODate("2011-08-08T04:03:22Z"), "errmsg" : "still initializing" } ], "ok" : 1 } How could this happen? I just follow the guide in the document, did I do something wrong? Moreover, I can't do anything on current secondary server. It doesn't allow me to reconfig on the secondary node, but the problem is there is no primary node. myset:SECONDARY> rs.reconfig({}) { "errmsg" : "replSetReconfig command must be sent to the current replica set primary.", "ok" : 0 } Any ideas?

  Read the article

• When I restart my virtual enviorment it does not re-bind to the IP address

  - by RoboTamer

  The IP does no longer respond to a remote ping With restart I mean: lxc-stop -n vm3 lxc-start -n vm3 -f /etc/lxc/vm3.conf -d -- /etc/network/interfaces auto lo iface lo inet loopback up route add -net 127.0.0.0 netmask 255.0.0.0 dev lo down route add -net 127.0.0.0 netmask 255.0.0.0 dev lo # device: eth0 auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.22.189.58 netmask 255.255.255.248 gateway 192.22.189.57 broadcast 192.22.189.63 bridge_ports eth0 bridge_fd 0 bridge_hello 2 bridge_maxage 12 bridge_stp off post-up ip route add 192.22.189.59 dev br0 post-up ip route add 192.22.189.60 dev br0 post-up ip route add 192.22.189.61 dev br0 post-up ip route add 192.22.189.62 dev br0 -- /etc/lxc/vm3.conf lxc.utsname = vm3 lxc.rootfs = /var/lib/lxc/vm3/rootfs lxc.tty = 4 #lxc.pts = 1024 # pseudo tty instance for strict isolation lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.mtu = 1500 #lxc.cgroup.cpuset.cpus = 0 # security parameter lxc.cgroup.devices.deny = a # Deny all access to devices lxc.cgroup.devices.allow = c 1:3 rwm # dev/null lxc.cgroup.devices.allow = c 1:5 rwm # dev/zero lxc.cgroup.devices.allow = c 5:1 rwm # dev/console lxc.cgroup.devices.allow = c 5:0 rwm # dev/tty lxc.cgroup.devices.allow = c 4:0 rwm # dev/tty0 lxc.cgroup.devices.allow = c 4:1 rwm # dev/tty1 lxc.cgroup.devices.allow = c 4:2 rwm # dev/tty2 lxc.cgroup.devices.allow = c 1:9 rwm # dev/urandon lxc.cgroup.devices.allow = c 1:8 rwm # dev/random lxc.cgroup.devices.allow = c 136:* rwm # dev/pts/* lxc.cgroup.devices.allow = c 5:2 rwm # dev/pts/ptmx lxc.cgroup.devices.allow = c 254:0 rwm # rtc # mounts point lxc.mount.entry=proc /var/lib/lxc/vm3/rootfs/proc proc nodev,noexec,nosuid 0 0 lxc.mount.entry=devpts /var/lib/lxc/vm3/rootfs/dev/pts devpts defaults 0 0 lxc.mount.entry=sysfs /var/lib/lxc/vm3/rootfs/sys sysfs defaults 0 0

  Read the article

• Site to Site VPN with Fault Tolerence

  - by Nordberg

  Hello, I have a situation where I require an IPSEC tunnel between two sites. Site 2 is a small branch office with basic (ADSL) connectivity and Site 1 is the "main" office with SDSL and ADSL for redundancy should the SDSL fail. From Site 1, all traffic bound for the 172.0.0.0 network will then be sent down another IPSEC tunnel to a supplier's Remote Server. See this page for the basic premise (this is a rough idea and things can be moved about etc...) I am considering specifying Cisco ASA devices as the firewalls for both sites for all connections. Would it be possible to employ something like HSRC to provide a backup at Site 1 should the SDSL go down? I suppose the key aims here are that Site 2 can somehow failover to initiate a VPN to the ASA behind the ADSL at Site 1. I will have a 21 subnet mask on all internet connections so can play with Class C routing if need be... If I'm barking up the wrong tree with HSRC, is there another way I can acheive this without massive expenditure on Barracuda routers et al? Many Thanks.

  Read the article

• IPCop Packet Mangling

  - by Zenham

  I've found myself in a pickle replacing an old firewall for a client this afternoon. I'm configuring their new IPCop firewall (1.4.21), Zerina OpenVPN addon is installed. What I need to do: There are three network interfaces, currently set up as red (WAN), green (LAN, 192.168.20.0/24) and orange (remote network 10.1.20.0/24). The orange interface is a direct fiber link to another organization. Simple description: Traffic and networks appear to be properly configured at this point, but I have many (150+) specific IPs on the LAN which, when accessing the resources on the 10.1.20.x network, need to be mangled to appear to be coming from the 10.1.20.0/24 network (and return traffic properly delivered). The routing on the far side was configured earlier and should be fine, but I need to redirect any packets coming across destined for those IPs to end up at their proper destination. The addressing is fixed and predictable (ie. 192.168.20.125 - 10.1.20.125). I need to insert whatever rules I have into the IPCop ruleset through /etc/rc.local I know, I'm just not sure about how I should structure this. There's CUSTOMOUTPUT and CUSTOMINPUT targets, both which currently just consist of the single rule redirecting packets to the OVPNOUTPUT/OVPNINPUT targets, so I'm guessing I should insert a rule matching outbound packets destined for the 10.1.20.x network and redirecting to a new target (maybe called TO-ORANGE) and a rule at the top of CUSTOMINPUT which redirects to a FROM-ORANGE target. Under those targets, I would have rules which do the IP matching and mangling. Am I approaching this right? If so, I'm not very familiar with mangle, and would appreciate seeing examples of how to write that source-IP rewrite. If not, how would you suggest doing this? TIA! edit: I notice additionally that the nat table has CUSTOMPREROUTING and CUSTOMPOSTROUTING targets, I guess I could alternatively post the rules in there....

  Read the article

• Could not continue scan with NOLOCK due to data movement during installation

  - by dbdev1

  Hi, I am running Windows Server 2008 Standard Edition R2 x64 and I installed SQL Server 2008 Developer Edition. All of the preliminary checks run fine (Apart from a warning about Windows Firewall and opening ports which is unrelated to this and shouldn't be an issue - I can open those ports). Half way through the actual installation, I get a popup with this error: Could not continue scan with NOLOCK due to data movement. The installation still runs to completion when I press ok. However, at the end, it states that the following services "failed": database engine services sql server replication full-text search reporting services How do I know if this actually means that anything from my installation (which is on a clean Windows Server setup - nothing else on there, no previous SQL Servers, no upgrades, etc) is missing? I know from my programming experience that locks are for concurrency control and the Microsoft help on this issue points to changing my query's lock/transactions in a certain way to fix the issue. But I am not touching any queries? Also, now that I have installed the app, when I login, I keep getting this message: TITLE: Connect to Server Cannot connect to MSSQLSERVER. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 67) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=67&LinkId=20476 BUTTONS: OK I went into the Configuration Manager and enabled named pipes and restarted the service (this is something I have done before as this message is common and not serious). I have disabled Windows Firewall temporarily. I have checked the instance name against the error logs. Please advise on both of these errors. I think these two errors are related. Thanks

  Read the article

• How does a vsftpd server work and how to configure it?

  - by ysap

  I was asked to configure a FTP server, based on the vsftpd package. The server is running on a remote machine to which I have a superuser privilege access. Being unfamiliar with the mechanics of FTP servers, I tried to figure out how user ftp accounts are configured. The previous maintainer used a shell script, which works on a list that we maintain to track users accounts and passwords, to configure the ftp accounts. From reading the script, I see that he generates a list of usernames and passwords, and actually creates a user account on the Linux machine. This means that for each user that we configure in the list, a new user account is being added by the adduser command: adduser --home /home/ftp --no-create-home $user (but w/o a private /home/username directory - using the /home/ftp instaed). Each of these users can log into his account using the ssh command. This fact seems a little strange to me, as I'd think that the ftp account should be decoupled from the Ubuntu user accounts. As another side effect, when a user connects using a web browser, he is connected to the /home/ftp directory. However, he can then use "Up to a higher level directory" link to go up and effectively have access to all of our system. So, the questions are: Is this really how the FTP server supposed to work in terms of configuring ftp accounts? If not, how do I configure the vsftpd server in a way that I have only the superuser Ubuntu account on that machine and all ftp account are... just FTP user accounts? Additionally, these ftp account should be configured in terms of how and what they are allowed to access.

  Read the article

• Windows 2008 Server cannot access any network share

  - by Ramesh

  Hello friends I run a Windows 2008 server with SP2. This server acts as a desktop alone. Recently, I switched between two networks (corporate and other) using this system. Ever since, I am unable to access any network share on the original network from where I installed and configured the desktop. The message I get is "Network path was not found". Note that I am able to access the internet and my corporate mail server. I am told this is a Vista and Windows 2008 specific problem and I have done everything I could think of: a) Deleted the second network settings from the desktop b) Installed a patch from MS that supposed took care of this problem (with MS clearly saying they had not tested this enough) c) The SP2 install was after the problem occurred and I went ahead with it in the hope that SP2 may have something that would fix this Some additional details: a) A system admin can log into this system from a remote terminal b) I cannot get into my own system using the hidden share C$ - for instance \mymachine\C$ gives me the same message as above - Network path not found c) I can log into my system remotely using mstsc d) I cannot create shares on this system - as an extension network printers are not detected I have an update for you: The error message is as follows - **Network Error** Windows cannot access \\network_share Check the spelling of the name. Otherwise there might a problem with your network. To try to identify and resolve network problems, click Diagnose. Clicking Diagnose gives Error Code: 0x80070035 The network path was not found. Any help will be appreciated Thanks

  Read the article

• Different routing rules for a particular user using firewall mark and ip rule

  - by Paul Crowley

  Running Ubuntu 12.10 on amd64. I'm trying to set up different routing rules for a particular user. I understand that the right way to do this is to create a firewall rule that marks the packets for that user, and add a routing rule for that mark. Just to get testing going, I've added a rule that discards all packets as unreachable: # ip rule 0: from all lookup local 32765: from all fwmark 0x1 unreachable 32766: from all lookup main 32767: from all lookup default With this rule in place and all firewall chains in all tables empty and policy ACCEPT, I can still ping remote hosts just fine as any user. If I then add a rule to mark all packets and try to ping Google, it fails as expected # iptables -t mangle -F OUTPUT # iptables -t mangle -A OUTPUT -j MARK --set-mark 0x01 # ping www.google.com ping: unknown host www.google.com If I restrict this rule to the VPN user, it seems to have no effect. # iptables -t mangle -F OUTPUT # iptables -t mangle -A OUTPUT -j MARK --set-mark 0x01 -m owner --uid-owner vpn # sudo -u vpn ping www.google.com PING www.google.com (173.194.78.103) 56(84) bytes of data. 64 bytes from wg-in-f103.1e100.net (173.194.78.103): icmp_req=1 ttl=50 time=36.6 ms But it appears that the mark is being set, because if I add a rule to drop these packets in the firewall, it works: # iptables -t mangle -A OUTPUT -j DROP -m mark --mark 0x01 # sudo -u vpn ping www.google.com ping: unknown host www.google.com What am I missing? Thanks!

  Read the article

< Previous Page | 411 412 413 414 415 416 417 418 419 420 421 422  | Next Page >