Search Results

Search found 13331 results on 534 pages for 'fluent interface'.

Page 423/534 | < Previous Page | 419 420 421 422 423 424 425 426 427 428 429 430  | Next Page >

• ipv6 with KVM on debian

  - by Eliasdx

  I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

  Read the article

• Small office network setups

  - by user39822

  I work at a small office and we're overhauling our network setup there. We're a web dev company and at the moment we have 50+ production sites running on the same machine that runs our internal email, which is just plain stupid. We're moving all our client hosting off site and are now looking for something to run our internal office requirement. Below is a brain dump: Equal amount of Mac & PC, about 25 machines in total. We need a central "server" to host files that should be accessible everyone as a "network drive". If possible we'd like to use low cost hardware for this (Mac or Win based). Disk space should be upward of 1TB. Ideally we should also be able to run a small web server on this machine (LAMP stack) to run some planning and billing applications we wrote ourselves. We need some sort of MS Exchange alternative for things like a shared calendar and especially being able to set Out of Office replies. We have one printer that is connected to the network Setup should be something can preferably be managed easily via a graphical interface and NOT require command line skills. Users want to keep using Apple Mail or MS Outlook After a quick google I came across the Zimbra collaboration suite, can anyone recommend this or any other solution for our office?

  Read the article

• What Media Extender / Centre Set up should I use?

  - by Bryn Hird

  I have installed cat6 throughout the house which I use for telephony and network. In my cellar I have a NAS Server, gigabit switch and I want to install a Media Centre to stream my video's, music, photo's and live TV (coax from the aerial to the cellar) over the cat6. Yeah I know I can get stuff on the internet but shared experience of watching TV as a family as it happens is a big plus for live TV. I'm aiming for 1080p. I want different users to be able to watch different channels. Max users = 4. I've played a little with Windows Media Centre, works fine with live TV. Likewise I have XBMC up and running with live TV. The issue I have is what do I put near the TV. I'd like a consistent user interface (grandma and the the other technophobes in the house are continually pestering me on how to use different TVs, change channel, inputs etc.) so a key part of this for me is to make the user experience the same and simple i.e. no keyboards / PCs hanging around the TV. I've just bought a Linksys DMA 2200 to test the Windows Media Centre, but obviously off eBay as they're a dying breed. And with Windows Media Centre removed from Microsoft plans such devices will get rarer. And as for 1080p, think I can forget it with that set up. I have tested XBOX 360, also works but ditto on Microsoft plans for WMC. I was thinking of a WD Live TV to test the XMBC setup. Now to the question. Any advice on Media Centre / Extender setups that will do the job as above and have some degree of futureproofing (building my own with my Raspberry PI is a last resort). I'd like to understand the standards involved in the futureproofing if anyone knows (DNLA, RVU etc.).

  Read the article

• Run a script on user connection on the VM host

  - by Scott Chamberlain

  I have a server running a Virtual Desktop Managed Pool, what I would like to do is when a user logs in I would like a script to check the number of available VMs and if below a threashold add additional VMs to the pool. The script to check the load and add to the pool is not the problem, I have that already figured out: $collectionName = "Test1"; $rdvh = "vmHost.example.com"; $minAvailableVMs = 2; Import-Module RemoteDesktop; $pool = Get-VirtualDesktopCollection -CollectionName $collectionName; $availableVMs = $pool.Size - ($pool.Size * $pool.PercentInUse / 100); $status = Get-VirtualDesktopCollectionJobStatus $collectionName #only add new servers if we are below the threashold and in the JOB_COMPLETEED state if($availableVMs -lt $minAvailableVMs -and $status.Status -eq [Microsoft.RemoteDesktopServices.Management.VirtualDesktopCollectionJobStatus]::JOB_COMPLETED) { Add-RDVirtualDesktopToCollection -CollectionName $collectionName -VirtualDesktopAllocation @{"$rdvh" = 1} } The problem I am having is, how do I run the above script on the Virtualization Host/Connection Broker/Some other server when a user connects?. I don't think it would be appropriate to run this as a logon script inside the VM, I think there is a way to do this on the management side but I don't know the new scripting interface in Server 2012 R2 well enough to know which commandlets I should look for to schedule this. EDIT: I know System Center is perfect for this but I do not have a license and was denied when I asked for it to be added to the budget.

  Read the article

• Virtualizing an Inline network appliance with VirtualBox (or VMWare)

  - by Tzury Bar Yochay

  My device, which is a Linux based IP in-liner is transparent to the network peripherals, that is, no IP address assigned to any of its interfaces. For the sake of the conversation, let's use ADSL connection as an example, while the device is inspecting the bi-directional traffic, the network is behaving same as if device was not there, attached to the wire (see Physical setup at the attached diagram). I wonder if I can enclosed that "device" within a Windows machine and have it operated virtually so it still seats inline between the ADSL router and the Windows netwroking interface by using virtual NICs, (or whatever their name is in windows), and inspecting the traffic, same as if it was on a separate physical device, the drawing under "Virtual Setup" in the attached diagram show what I am trying to achieve. Reading a bit on the VirtualBox docs, seems like binding the right side is relatively simple, perhaps I should have one network adapter set as Bridge Networking and VirtualBox will connect it to the physical NIC on the host machine, and network packets are exchanged directly, circumventing the host operating system's network stack (WinXP in my case). However, I have no idea how to achieve the left side of my diagram, which requires adding virtual NICs to windows and configure them correctly in a way to make that pipeline possible. I would appreciate any help. by the way, if that is not possible with VirtualBox but with other virtualization solution (e.g. VMWare), I would accept the other as well.

  Read the article

• On Windows machines, what is the typical toolchain for remote maintenance?

  - by Hanno Fietz

  I need to deploy PHP and Python code and the appropriate environment (web server, db server) to remote Windows systems, and I don't know what toolchain would be the equivalent to ssh, scp, bash and the like. So, basically, what I need to be able to do is the following: access remote Windows with the appropriate privileges in a secure manner, like I routinely do with ssh (I don't even know whether that would be a text or graphic interface on Windows). remotely install software: Apache or IIS, MySQL or Postgres, Python or PHP copy files from remote (the application we're deploying) remotely configure the machine to run regular tasks (e. g. checking for updates to the application) automate tasks like downloading files from a designated place The main question is probably how I get onto the machine securely in the first place, and then the rest is general Windows admin knowledge, which probably is too broad a scope to fit into one question. I have years of experience with maintaining Linux boxes and I have used tools of varying sophistication on those, ranging from plain scping of PHP files to deployment of Java application containers and even full VMs with Vagrant. On Windows, I'm a complete noob, and I don't even know where to start. I have installed Apache, MySQL , PHP on a desktop machine maybe twice in my life, that's about it. Bonus points for things that work from a Linux machine at my end, but I could run a VM and do everything from there.

  Read the article

• How to avoid sshfs freezing?

  - by Andreas Hagen

  So the issue is this: I've installed sshfs on Ubuntu 12.04 and I'm trying to connect to a couple of remote servers. So initially the mount seams successful. Sometimes Gnome even picks it up and displays the "new device found" box at the bottom of the screen. but from here on there is not much that works. Or at least not any more. The first couple of times i connected it seamed to work fine, and I was able to transfer some files, then i disconnected using fusermount -u <folder> and after reconnecting a little later the trouble started. Now after executing sshfs -o ServerAliveInterval=15 -o reconnect -C -o workaround=all -o idmap=user root@<host>:/ <folder>, when I change directory into the mount-point, the shell just freezes. Strangely ls -al <folder> works when listing just the root of the remote system, but nothing more. Also every file-explorer I've tried freezes just like cd <folder>. To me it seamed like there was some kind of zombie thread or something hanging around my system, due to the fact that it did work the first time, so I have tried rebooting but no luck. sshfs -V gives this: SSHFS version 2.3 FUSE library version: 2.8.6 fusermount version: 2.8.6 using FUSE kernel interface version 7.12 So yea, any ideas?

  Read the article

• How to merge arbitrary snapshot into base vdi in Virtualbox

  - by jmathew

  I botched a transfer of a VM from one harddisk to the other. Now I'm left with the base vdi and a whole bunch of snapshots. My steps Copied old VM directory over to new HDD Deleted old VM and added new VM using using Machine-add and providing the old XML file Couldn't add base vdi file due to conflict so changed the UUID of base vdi with VBOXMANGE.EXE internalcommands sethduuid <path/to/vdi> Attempt to rollback to a snapshot, but it seems the VM is looking for the snapshots on the old HDD (which is formatted and gone) This is the error (networked is the name): Failed to restore the snapshot networked of the virtual machine lfs. Could not open the medium 'H:\vm\ft.vdi'. VD: error VERR_PATH_NOT_FOUND opening image file 'H:\vm\ft.vdi' (VERR_PATH_NOT_FOUND). Result Code: E_FAIL (0x80004005) Component: Medium Interface: IMedium {53f9cc0c-e0fd-40a5-a404-a7a5272082cd} The old HDD was drive H: the new one is drive N: How can I modify the snapshots/VM to look in N:\vm\ft.vdi for the base vdi? I've already set the default settings in VirtualBox in general (default vm/vm snapshot location). Or if not that how can I merge the old snap shot with the base vdi given that the only things that have changed is the base vdi's UUID?

  Read the article

• Domain Trust 2008 to 2003

  - by nick3216

  I'm having trouble setting up the trust relationship between a Windows Server 2003 and a Windows Server 2008 AD. Domain a is Windows Server 2003 Forest functional level. Domain b is a Windows Server 2008 Forest functional level. I can set up the incoming side of the trust relationship on domain "a" so that it trusts domain "b". Try as I might on domain "b" I can't set up the outgoing side of the trust relationship to domain "a". The GUI interface gives an unhelpful 'The request is not supported'. I'm not sure netdom is being more or less helpful as it refers me to FilterSIDs netdom trust /add b /uo:b\admin /po:* /d:a /ud:a\admin /pd:* /oneside:trusting To improve the security of this external trust, security identifier (SID) filtering is enabled, however, if users have been migrated to the trusted domain and their SID histories have been preserved, you may choose to turn off this feature. For more information about SID filtering and how to turn it off, see the help for netdom trust /FilterSids or see Help and Support. The request is not supported. The command failed to complete succesfully. I say 'less helpful' because Windows Server 2008 doesn't support the /FilterSIDs option. How can we force creation of this trust? Edit: Just to clarify I've checked that the [Computer Configuration\Windows Settings\Security Settings\Local Policies\Security Options] "Network access: Allow anonymous SID/Name translation” is enabled on both sides of the trust as per http://social.technet.microsoft.com/Forums/en/winserverDS/thread/cc61fc25-3569-4413-bbfd-92390eb31118

  Read the article

• Windows VirtualBox failed to attach USB device to Linux Guest

  - by joltmode

  I have Windows 7 64bit Host system, and I am using VirtualBox 4.1.18 (r78361). I have an Arch Linux Guest OS. I have installed VirtualBox Extension Pack (to enable USB2 support) and added my USB device filter to VM. I have also installed the Guest Additions provided by Arch: virtualbox-archlinux-additions (but I have no idea whether it's actually needed for my environment). I can see my USB device from VirtualBox Devices menu. Whenever I am trying to access it, I end up with: Failed to attach the USB device Kingston DT 100 G2 [0100] to the virtual machine Archlinux. USB device 'Kingston DT 100 G2' with UUID {a836ec33-0f41-4ca7-a31d-09cceaf5d173} is busy with a previous request. Please try again later. Details ? Result Code:    E_INVALIDARG (0x80070057) Component:      HostUSBDevice Interface:      IHostUSBDevice {173b4b44-d268-4334-a00d-b6521c9a740a} Callee:         IConsole {1968b7d3-e3bf-4ceb-99e0-cb7c913317bb} From what I have googled, most guides shows how to solve this the other way around - Linux Host to Windows Guest. How do I resolve this? Update I have tried to Eject (virtually, not physically) the device from my Windows Host system and then try to access the Device from Guest. Same error.

  Read the article

• Route return traffic to correct gateway depending on service

  - by Marnix van Valen

  On my office network I have two internet connections and one CentOS server running a website (HTTPS on port 443). The website should be publicly accessible through the public IP of the first internet connection (ISP-1). The other internet connection, ISP-2, id the default gateway on the network. Both internet connections have routers (the household-kind) with NAT, SPI firewalls etc. The router on ISP-2 is a Netgear WNDR3700 (aka N600) with original firmware. The problem is that the website is unreachable. Looks like incoming traffic on ISP-1 will reach the server but the returning traffic is routed through ISP-2, effectively making the site unreachable. As far as I can tell I can't do port based routing on the WNDR3700. What are my options to make this work? I've been looking at implementing an iptables / routing based solution on the server itself but haven't been able to make that work. Update: Note that the server has one network interface connecting it to both routers.

  Read the article

• openvpn problem

  - by Jared Voronik

  I have a problem with openvpn. I have already setup openvpn sucessfully on some other servers in the past (basic configuration, nothing special). On this server, I used the same config file, but for setting up nat iptables -t nat -A POSTROUTING -s 10.4.0.0/24 -o eth0 -j MASQUERADE doesn't work. It gives error: iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. How do I fix this error? Also, if I can't fix this error, can I do bridging instead of routing? I have only 1 interface, and I can connect to remote server only via ssh (and need to avoid reboots if at all possible) so if briding means a whole ethernet card has to be devoted to the openvpn (and no other servers) then briding is out, otherwise I can use briding. Do you know of a simple, step by step guide to configure openvpn briding (just simple openvpn server and clients that can access internet through vpn server, nothing fancy)?

  Read the article

• Managing rolling deployments in the cloud

  - by Josh Nankin

  Recently I've been experimenting with various cloud management tools like RightScale, Scalr, custom scripts for managing a variety of servers, each hosting several roles (app, db, load balancer, job queues, etc). The one thing I find lacking in most solutions is a way to do rolling deployments, i.e. running deployments sequentially across a number of servers with the same role. For instance, I dont want to build all of my webservers at the same time, as that will almost definitely result in some down time or 500s for my customers. I'd rather have one or two servers build at a time, while other servers are still available to handle requests. The other alternative is obviously to launch new servers that automatically update themselves on boot, but this isn't as cost effective, and most likely requires more time for the build to complete (it's faster to build on an existing server than to launch a new server and kill old ones). We've all heard of the big companies having the famous "push to build" button (companies like Twilio, Etsy, etc.) but it seems that they all have custom implementations of this. I'm not talking about a simple ssh-loop, clusterssh, or even an mcollective - I preferably want something with a nice simple interface that allows me to specify something like a RightScript or a Scalr script to run on a set of servers with a specific role, and it builds them sequentially. Does any one know of easy ways to get this done, or is this a candidate for a new open source project?

  Read the article

• Trying to communicate between virtual servers on the same host through ipv6

  - by Daniele Testa

  I am running KVM on a host with 2 virtual servers. Each virtual server has a own bridge interface on the host VPS1 has br1 VPS2 has br2 Each virtual server has a own ipv4 and a ipv6. The virtual servers has no problem communicating with internet or with eachother through ipv4. However, with ipv6, they can only communicate with internet and NOT with eachother. The host can ping the 2 virtual servers without any problems, but they cannot ping eachother. iptables has been set to ACCEPT on all chains, so it is not the problem. VPS1 has ipv6 = 2a01:4f8:xxx:xxx::10 VPS2 has ipv6 = 2a01:4f8:xxx:xxx::5 the host has the following routes set: ip route add 2a01:4f8:xxx:xxx::10 dev br1 ip route add 2a01:4f8:xxx:xxx::5 dev br2 When I do a ping from VPS2 to VPS1, I see the following on the host: tcpdump -i br1 15:32:27.704404 IP6 2a01:4f8:xxx:xxx::10 > ff02::1:ff00:5: ICMP6, neighbor solicitation, who has 2a01:4f8:xxx:xxx::5, length 32 So it seems like the host is seeing the request coming from VPS1 on br1. But for some reason, it does not forward it to br2. Instead it is asking where the destination IP is through ipv6 multicast. Anyone has a clue what is going on? I find this very strange, as it is working fine with ipv4 with the exact same settings and routes.

  Read the article

• UDP blocked by Windows XP Firewall when sending to local machine

  - by user36367

  Hi there, I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: - Windows XP Professional with Service Pack 3, all updated - Program that sends UDP datagrams - Program that receives UDP datagrams - Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas? Thanks in advance!

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• Connect to WEP Wireless Network by command line on Ubuntu

  - by Tim

  Hi, I am a newbie to both network and Linux. I am now trying to connect to a WEP wireless network by command line on my Ubuntu 8.10, because the Network Manager does not support 64 bit WEP. (1) I firstly bring down the Network Manager and then try to connect to a wireless network, whose essid is candy and password is 5673212741. But it fails as shown in the following. I wonder why and how to do it correctly? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwconfig wlan0 essid candy opendo iwconfig wlan0 key 18018ce78e open $ sudo iwconfig wlan0 key 5673212741 open $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 9971 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 20 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9 No DHCPOFFERS received. No working leases in persistent database - sleeping. $ ping www.bbc.co.uk ping: unknown host www.bbc.co.uk (2) A less important question: why the scan for wireless networ does not work after I bring down the Network Manager? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning : Network is down Thanks and regards!

  Read the article

• Different external ip addresses from different sites

  - by user630286

  My router is ClearOS 6(Centos 6). In my router, I have two external (internet) network connections from two ISP's. The primary connection is eth2 connected to a cable modem and the second one is ppp0 connected to a dsl modem. I have assigned eth2 as the primary connection (with a high metric value). In fact this is done through clearos's multiwan web interface. I have a test in my Nagios to monitor whether the primary connection. This connection is done based on the result of curl ifconfig.me But it seems that ifconfig.me is always giving the ip address of my secondary connection. I tested it through a browser. Yes ifconfig.me gives the secondary internet's(ppp0) ip address. But whatismyipaddress.[com|org] give my primary ip address (eth2). I checked the default route on the router through ip route list 0/0 which also shows the primary connection (eth2) as the default route. The traceroute www.google.com and traceroute ifconfig.me both seems to trace through the primary connection (eth2). As our secondary internet connection has only got a limited download, I don't want to end up having to pay a large sum at the end of the month. Has somebody got an idea why the ifconfig.me shows my secondary address? What is the best way to ensure that my router(and thus the lan) use the right internet connection.

  Read the article

• GUI interfaces to ATI card behave weirdly out of the box and after updates.

  - by jdk

  My Lenovo W500 came with an ATI Mobility FireGL V5700 and both the Catalyst control center software and Vista display manager display four monitors. What's really annoying is the behaviour. My two active displays (laptop display + my external monitor) are always #s 3 and 4 respectively which doesn't make sense. This is out of the box. Additionally dragging & dropping is jumpy and displays #1 and 2 (always inactive because they don't exist to the software) are often preventing me from dragging #3 and 4 to the rightmost side. They also auto-snap to weird positions and certain sensible positions like position one directly over top of the other are not possible. The exact same annoyances are present when using the Windows Display manager too. In other words the interface is crap and I'm looking for a fix that's not wishing I had gone with nVidia instead. I've updated drivers, and Catalyst control centre. Have latest Windows and AMD/ATI updates. Any thoughts? Graphics Software Driver Packaging Version 8.563.2.1-090401a-079160C-Lenovo Provider ATI Technologies Inc. 2D Driver Version 7.01.01.849 2D Driver File Path /REGISTRY/MACHINE/SYSTEM/ControlSet001/Control/Class/{4D36E968-E325-11CE-BFC1-08002BE10318}/0001 Direct3D Version 7.14.10.0630 OpenGL Version 6.14.10.8306 Catalyst® Control Center Version 2009.0401.1328.22301 Graphics Hardware Primary Adapter Graphics Card Manufacturer Powered by ATI Graphics Chipset ATI Mobility FireGL V5700 Device ID 9591 Vendor 1002 Subsystem ID 2126 Subsystem Vendor ID 17AA Graphics Bus Capability PCI Express 2.0 Maximum Bus Setting PCI Express 2.0 x16 BIOS Version 010.088.000.021 BIOS Part Number BK-ATI VER010.088.000.021.034663 BIOS Date 2009/09/30 Memory Size 512 MB Memory Type DDR3 Core Clock in MHz 600 MHz Memory Clock in MHz 700 MHz

  Read the article

• Finding default gateway in an openvpn environment in windows

  - by Alexander Trümper

  I need to find the default gateway in a openvpn scenario where the route output looks like that: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.49.73.1 10.49.73.24 10 0.0.0.0 128.0.0.0 10.8.0.1 10.8.0.2 30 So I googled around a bit and a found this script here: @For /f "tokens=3" %%* in ( 'route.exe print ^|findstr "\<0.0.0.0\>"' ) Do @Set "DefaultGateway=%%*" echo %DefaultGateway% This works, but matches both lines in the route output. But I need to find this line: 0.0.0.0 0.0.0.0 10.49.73.1 10.49.73.24 10 So I tried to modify the findstr parameter like this: findstr "\<0.0.0.0\>.\<0.0.0.0\>" in the expectation that '.' will match for the tab between the columns. But it doesn't. It will still set DefaultGateway to 10.8.0.1 I couldn't find a clue in MS documentation either. Maybe someone knows the right expression? Thanks a lot.

  Read the article

• NTBackup (on WS2k3) fails to backup remote server (WS2k8R2) with " Error: is not a valid drive, or you do not have access."

  - by Mark A

  We run an NTBackup job on a Windows Server 2003 R2 SP2 with all updates (as of Q4-2011). It works well backing up two WS2k3 servers as well as the backup server itself. However, we have been unable to successfully back up our Windows Server 2008 R2 machine ("G5-01"). It often runs for about 2GB worth of backup and then dies out with one of the below error messages. It should be more like 20GB for the full server. We have tried using the admin share (C$), an explicitly shared drive share, UNC and mapped drives. The result is the same each time, the only thing that varies is the amount of stuff backed up before it chokes. We've also run NTBbackup from the UI interface, from the command line and as a scheduled task. We are backing up to 400/800GB tapes and they have plenty of space available on them (blank media). Error: \\G5-01\c is not a valid drive, or you do not have access. Error: \\G5-01\c$ is not a valid drive, or you do not have access. Error: Y: is not a valid drive, or you do not have access. Error: Could not access or create backup catalog files. Verify that you have full access to the working folder and there is disk space available. The job is run as Administrator and we have no problems logging onto the server and transferring files. The Event Log on the WS2k8 is not much help, as it has success audits for each login. All of the hardware involved (HP DL360 G3, HP LTO Ultrium 3, Adaptec 39320A) has the latest supported drivers. We've seemingly tried a bunch of different options but are wondering where to look next to resolve the backup issue. We've been super happy with our reliable schedule task for years but this one is stumping us!

  Read the article

• No LAN and SMB access, and Explorer not responsive, when using a second connection

  - by Lorenzo

  I apologize if this is a duplicate question, I know that there are several questions about multiple connection (LAN + LAN and LAN + dialup) but I haven't been able to find one that fits my scenario. I'm still using Windows XP on my corporate laptop, and I'm connected to the corporate LAN via Ethernet. The LAN NIC has a public IP address, although not accessible externally, obtained via the corporate DNS server. This connection is firewalled and requires a proxy to access Internet. To access Internet sites blocked by the corporate firewall, I use my smartphone via USB tethering. It is seen as a new LAN interface, and I get a private IP address (class 192.168..). There are two problems: The LAN is not accessible, as the default gateway goes to the tethering NIC. I'd like to solve this, but I can live with it. My PC becomes unresponsive if I use Windows Explorer to view local files, or even when I open the start menu. I guess that this is caused by attemps to connect to a mapped network drive. But I disabled the "Client for Microsoft Networks" in the tethering NIC. Why the system still hangs? Of course if I disable the Ethernet NIC, Explorer stops hanging. If you need further details, add a comment. Thanks!

  Read the article

• What are the replacement options for an IDE hard disk for a DOS based system?

  - by dummzeuch

  I have got a few "embedded" systems running MSDOS 6.2 which boot from and store data to IDE hard disks. Since these drives are nearing their end of life, the question arises how we can replace them. The requirements are: DOS must be able to install and boot from these drives. They must be able to sustain heavy (mostly) write access. If possible, they should be able to survive moderate vibrations (not too bad since the current hard disks have survived several years of that) I considered the following options so far: other ide hard drives: Unfortunately modern IDE drives are too large so DOS cannot boot from them even if I create small partitions. Older IDE drives are just that: old, so they are probably not the most reliable ones any more. SSDs: There are a few SSDs with IDE interface available. I have not yet tried them. Does anybody have any experience with them? They look like the ideal replacement provided that DOS can boot from them and that writing speed does not deteriorate too much (the old hard disks are no race cars either). Compact Flash: There are adapters for using CF with IDE controllers and they work fine. DOS can boot from them and they have no problems at all with vibrations. What I am not sure about is their durability. DOS uses FAT so some very few sectors are written every time the medium is being written to. IDE to SATA converters: I have no idea whether they are any good. Has anybody tried them? It might be an option to use one of these to connect an SATA SSD to the system. Are there any alternatives that I have missed? (We are working on replacing these systems, but it will still take a few years.)

  Read the article

• IPTABLE & IP-routed netwok solution for HOST net and VM's subnet

  - by Daniel

  I've got ProxmoxVE2.1 ruled KVM node on Debian and bunch of VM's guests machine. That is how my networking looks like: # network interface settings auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 175.219.59.209 gateway 175.219.59.193 netmask 255.255.255.224 post-up echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp And I've got two working subnet solution auto vmbr0 iface vmbr0 inet static address 10.10.0.1 netmask 255.255.0.0 bridge_ports none bridge_stp off bridge_fd 0 post-up ip route add 10.10.0.1/24 dev vmbr0 This way I can reach internet, to resolve outside hosts, update and download everything I need but can't reach one guest VM out of any other VM's inside my network. The second solution allows me to communicate between VM's: auto vmbr1 iface vmbr1 inet static address 10.10.0.1 netmask 255.255.255.0 bridge_ports none bridge_stp off bridge_fd 0 post-up echo 1 > /proc/sys/net/ipv4/ip_forward post-up iptables -t nat -A POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE post-down iptables -t nat -D POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE I can even NAT internal addresses: -t nat -I PREROUTING -p tcp --dport 789 -j DNAT --to-destination 10.10.0.220:345 My inexperienced mind is ready to double VM's net adapters: one for the first solution and another - for second (with slightly different adresses) but I'm pretty sure that it's a dumb way to resolve the problem and everything can be resolved via iptables/ip route rules that I can't create. I've tried a dozen of "wizard manuals" and "howto's" to mix both solution but without success. Looking for an advice (and good reading links for networking begginers).

  Read the article

• Best NIC config when virtual servers need iSCSI storage?

  - by icky2000

  I have a Windows 2008 server running Hyper-V. There are 6 NICs on the server configured like this: NIC01 & NIC02: teamed administrative interface (RDP, mgmt, etc) NIC03: connected to iSCSI VLAN #1 NIC04: connected to iSCSI VLAN #2 NIC05: dedicated to one virtual switch for VMs NIC06: dedicated to another virtual switch for VMs The iSCSI NICs are used obviously for storage to host the VMs. I put half the VMs on the host on the switch assigned to NIC05 and the other half on the switch assigned to NIC06. We have multiple production networks that the VMs could appear on so the switch ports that NIC05 & NIC06 are connected to are trunked and we then tag the NIC on the VM for the appropriate VLAN. No clustering on this host. Now I wish to assign some iSCSI storage direct to a VM. As I see it I have 2 options: Add the iSCSI VLANs to the trunked ports (NIC05 and NIC06), add two NICs to the VM that needs iSCSI storage, and tag them for the iSCSI VLANs Create two additional virtual switches on the host. Assign one to NIC03 and one to NIC04. Add two NICs to the VM that needs iSCSI storage and let them share that path to the SAN with the host. I'm wondering about how much overhead the VLAN tagging in Hyper-V has and haven't seen any discussion about that. I'm also a bit concerned that something funky on the iSCSI-connected VM could saturate the iSCSI NICs or cause some other problem that could threaten storage access for the entire host which would be bad. Any thoughts or suggestions? How do you configure your hosts when VMs connect direct to iSCSI?

  Read the article

< Previous Page | 419 420 421 422 423 424 425 426 427 428 429 430  | Next Page >