Search Results

Search found 14624 results on 585 pages for 'static'.

Page 425/585 | < Previous Page | 421 422 423 424 425 426 427 428 429 430 431 432  | Next Page >

• Remote network traffic not passing through VPN

  - by John Virgolino

  We have the following topology: LAN A LAN B LAN C 10.14.0.0/16 <-VPN-> 10.18.0.0/16 --- SONICWALL <-VPN-> M0N0WALL --- 10.32.0.0/16 Traffic between LAN A and LAN B works perfectly. Traffic between LAN C and LAN B works perfectly. Traffic between LAN A and LAN C, not so much. LAN A's gateway has a route to LAN C that points to the Sonicwall. The Sonicwall has a route to LAN A pointing to the VPN gateway connecting LAN B to LAN A. Tracing packets on the Sonicwall shows the LAN C destined traffic to arrive on the Sonicwall, but it does not forward the traffic, it dies there. Traffic from LAN B gets forwarded. Tracing packets on the Sonicwall while sending traffic from LAN C destined for LAN A shows nothing. This tells me that the M0N0WALL is not forwarding traffic for the 10.14.0.0 network and the Sonicwall is not forwarding from 10.14.0.0. The SA on the Sonicwall terminates on the WAN ZONE and is defined to use an address group that incorporates both the 10.14.0.0 and 10.18.0.0 networks. The M0N0WALL is configured for the 10.18.0.0 network and I have tried with both a static route to 10.14.0.0 and without on the M0N0WALL. I tried manually adding the 10.14.0.0 network to the SA on the M0N0WALL, but that really aggravated it and the SA never came up, so I reverted. I have checked all the firewall rules to make sure nothing is blocked. All of the Sonicwall auto-added rules look right. Specs: Sonicwall TZ200, Enhanced OS M0N0WALL v1.32 I'm at a loss at this point. Any help would be appreciated.

  Read the article

• Routing WIFI and LAN for specific traffic

  - by jakebird451

  I have two network devices aboard my macbook pro: WIFI (en1): Used for general traffic. Connects to an ip of 192.168.19.* via DHCP LAN (en0): Used for specific traffic. Connects to an ip of 192.168.2.10 as a static IP. Does not connect to a router, only a switch for direct routing connection. I have 4 IP addresses I need to access on the LAN: 192.168.2.1 192.168.2.21 192.168.2.20 192.168.2.30 The rest of the traffic needs to go to WIFI. I have tried setting up a routing table for the specific ip addresses, but I only managed to mess up my network. I do not venture out into the world of networking too often, but this was the latest command I have been trying: sudo route add -host 192.168.2.30 -interface en0 This command killed my ability to use ping. It told me that ping could not allocate memory (is that even possible)? It also killed my wifi access. Logging out and back in fixed the issue. I really do not mind to make this solution permanent, so I am fine with a temporary routing.

  Read the article

• No network connection for vmware esxi guests

  - by JavaDev

  I'm new to VMware and setting up an Esxi server as a trial with the intention of possibly virtualizing some of our servers in the near future. I have setup ESXi on a Dell poweredge server, and installed a Centos 5.6 and Ubuntu 11.04 guest os on the server. However I cannot get networking on my guest OS's. The host is connected to a network with a DHCP server via a switch and is configured with a static IP. I have the default set-up for networking on the host: both guests are connected to the default vmnic1 adapter via the virtual switch vSwitch0. One thing though, the virtual adapter shows 'Observed IP ranges' to be XXX.XXX.XXX.194-XXX.XXX.XXX.195 (I've blanked out the initial prefixes) i.e just 1 address, even though the network the host is connected to has the usual 255.255.255.0 subnet mask. On the guest machines (using DHCP) by default, I can see an eth0 interface but with no connection or assigned IP address. A physical machine connected to the network gets a DHCP lease as expected. How do I get networking working on my guest OSes? Apologies for the long-winded question.

  Read the article

• Multiple Routers, Failover, DHCP and multiple gateways. NOT WAN-failover

  - by u_b

  I've had a look around google and this forum but could not find an answer to my question. So probably one of you can help me a little. My intended setup is: Router R1: wan connection to isp. connected backup server. provides some wireless SSID. other connected devices like printer, laptop, etc. both wired and wireless. Router R2: no wan connection to isp but connected to R2. connects mp3-streamer and music server. also serves as a wireless access point with same SSID. other than described connections only wireless connections. I would like to be able to control music even if R1 is off, e.g. with no internet connection. On the other hand I would like to access internet also in the case that R2 is off, i.e. no music access. Last but not least I would like to stream internet radio, i.e., R1 and R2 are on, and music is streamed from internet to R1 to R2 to streamer. I would like to realize all this using DHCP (also using static assignments) so i do not have to configure statically on android, laptop, etc. So my questions are: Can I make DHCP provide a list of two default gateways R1,R2? In order to make clients fallback to other gateway if currently assigned gateway is turned off? Thanks in advance, u_b

  Read the article

• dhcp3-server (dhcpd) is tampering with host NIC

  - by user61000

  Hi all, I have a debian box that is serving as a router (using iptables NAT). When first turned on, everything works fine for a few minutes. Then the dhcp server assigns an IP (other than 192.168.0.1) to its' host NIC, eth0. This is NOT what I want. I just want dhcp3-server to listen on eth0, not assign it an IP, and changes the kernel routing table. This of course ruins the NAT capablities of the box. How can I tell the dhcp3-server NOT to do this? Thanks Before dhcp3-server tampers with eth0, the IP is 192.168.0.1, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 173.33.220.1 eth1 After dhcp3-server tampers with eth0, the IP is 192.168.0.3, and the routing table looks like this: ~# netstat -r Kernel IP routing table Destination Gateway Iface 192.168.0.0 * eth0 173.33.220.0 * eth1 default 192.168.0.1 eth0 default 173.33.220.1 eth1 SETUP Outbound NIC is eth1 Internal NIC is eth0 /etc/network/interfaces ... iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 /etc/default/dhcp3-server INTERFACES="eth0"

  Read the article

• How to troubleshoot Linksys E4200 Remote Management

  - by Jordan

  My Linksys E4200 is configured for Remote Management, but the router is not accepting the connections. Here's the configuration under Administration Management Remote Management Access: Remote Management: Enabled Access via: HTTP Remote Upgrade: Disabled Allowed Remote IP Address: Any IP Address Remote Management Port: 8080 The router is setup to use 192.168.10.41 as its static Internet IP address, and 192.168.35.1 as its LAN IP address. I can access the router just fine via its LAN IP address, but I can't make a connection using http://192.168.10.41:8080. I've tried variations of the settings above (enabled HTTPS, enabled Remote Upgrade, set an IP range of 192.168.10.1-254) but nothing has worked yet. Hoping someone can at least point me in the right direction. Thanks. Update: To clarify, I have a wired router that connects straight to the T1 modem. It's configured to use 192.168.10.1-254 as its internal LAN range. The E4200 wireless router in question is on that LAN using 192.168.10.41 as its WAN IP address. The E4200's internal LAN range is 192.168.35.1-254. I'm not trying to access the E4200 from the Internet, I'm just trying to access it from its WAN IP address. Thanks.

  Read the article

• why won't php 5.3.3 compile libphp5.so on redhat ent

  - by spatel

  I'm trying to upgrade to php 5.3.3 from php 5.2.13. However, the apache module, libphp5.so will not be compiled. Below is a output I got along with the configure options I used. The configure statement is a reduced version of what I normally use. ========== './configure' '--disable-debug' '--disable-rpath' '--with-apxs2=/usr/local/apache2/bin/apxs' ... ** ** ** Warning: inter-library dependencies are not known to be supported. ** ** ** All declared inter-library dependencies are being dropped. ** ** ** Warning: libtool could not satisfy all declared inter-library ** ** ** dependencies of module libphp5. Therefore, libtool will create ** ** ** a static module, that should work as long as the dlopening ** ** ** application is linked with the -dlopen flag. copying selected object files to avoid basename conflicts... Generating phar.php Generating phar.phar PEAR package PHP_Archive not installed: generated phar will require PHP's phar extension be enabled. clicommand.inc pharcommand.inc directorytreeiterator.inc directorygraphiterator.inc invertedregexiterator.inc phar.inc Build complete. Don't forget to run 'make test'. ============= php 5.2.13 recompiles just fine so something is up with 5.3.3. Any help would be greatly appreciated!!

  Read the article

• Debian Wheezy (testing) df reported volume size

  - by TheRoadrunner

  I am a bit confused about the /dev/sda* references since I installed Wheezy instead of Squeeze on a testing box. fdisk -l returns: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e9623 Device Boot Start End Blocks Id System /dev/sda1 * 2048 480278527 240138240 83 Linux /dev/sda2 480280574 488396799 4058113 5 Extended /dev/sda5 480280576 488396799 4058112 82 Linux swap / Solaris This seems correct. But df -h /dev/sda (and /dev/sda1 and /dev/sda2 and /dev/sda5) returns: Filesystem Size Used Avail Use% Mounted on udev 10M 0 10M 0% /dev The same happens with every entry under /dev/disk/by-id and /dev/disk/by-path. Only one of two entries under /dev/disk/by-uuid returns the correct volume size: df -h /dev/disk/by-uuid/cacdbad6-7e6b-4e80-84ba-e3c77ef48796 Filesystem Size Used Avail Use% Mounted on /dev/disk/by-uuid/cacdbad6-7e6b-4e80-84ba-e3c77ef48796 229G 22G 196G 11% / Contents of /etc/fstab: # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sda1 during installation UUID=cacdbad6-7e6b-4e80-84ba-e3c77ef48796 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=45840d13-ee36-4e77-8e73-16cbdff25eb1 none swap sw 0 0 /dev/sr0 /media/cdrom0 udf,iso9660 user,noauto 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto 0 0 It seems all other references than the uuid points to the swap partition. Is this because Wheezy is in testing, and should it be reported as an error?

  Read the article

• Proxmox: VMs and different public IPs

  - by Raj

  I have a server which has two NICs and both are directly connected to internet. I have five different public IP addresses available for the VMs. The host machine (Proxmox) doesn't need to use any (it'll use a private IP and that's all) but will have internet connection. I've gone through the Proxmox documentation and I'm not able to understand the big picture to set up the right network configuration for my needs. In short, what I have is: One server (Proxmox, host machine) On that server, 5 VMs are created 5 public IP addresses available (one for each VM), let's say: 80.123.21.1, 80.123.21.2, 80.123.21.3, 80.123.21.4, 80.123.21.5 What I have now for the host is the following: auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto eth1 iface eth1 inet manual auto vmbr0 iface vmbr0 inet static address 192.168.1.101 netmask 255.255.255.0 bridge_ports eth0 bridge_stp off bridge_fd 0 auto vmbr1 iface vmbr1 inet manual It can be reached from the internal network, so that's OK. It has internet connection, which is also OK. vmbr1 is going to be used by the VMs. Each VM will have its own IP on his network interfaces configuration file. For some reason, VMs will not have internet and they won't be able to have public IP address. If I use NAT, it will work correctly, but they will not use the public allocated IP addresses for them. Am I missing something?

  Read the article

• Setting a subdomain to access home machine with windows remote desktop

  - by ianhales

  I'm trying to remotely connect to home machine through Windows Remote Desktop (amongst other things, but this is currently my primary focus). I can do this fine using my home WAN's static IP (thank god for cable!) with port-forwarding, but I would like to access it from a subdomain of my web-site (e.g. home.mydomain.co.uk). In the cPanel for my hosting account, I've gone into DNS zones and altered the A-record to point to my WAN's IP, which I thought should do the job, but I still cannot connect. When I ping the subdomain, I get my web-host's IP, which I guess is to be expected as I believe the DNS of the host domain is used first, then my server handles the redirection of traffic to the IP in the A-record. Is this the correct idea? Do A-record changes suffer from the same propagation delays as DNS record changes, as I suppose that could explain it? (by the way, this thread confirms my thoughts that setting the A-record should be enough: Hostmonster Subdomain redirected to home server IP: How to ssh into home server using subdomain)

  Read the article

• Nginx: Loopback connection via PHP's getimage size crashes server (Magento's CMS)

  - by Alex

  We were able to trace down a problem that is crashing our NGINX server running Magento until the following point: Background info: Magento Backend has a CMS function with a WYSIWYG editor. This editor loads some pictures via a controller in magento (cms/directive). When we set the NGINX error_log level to info, we get the following lines (line break inserted for better readability): 2012/10/22 18:05:40 [info] 14105#0: *1 client closed prematurely connection, so upstream connection is closed too while sending request to upstream, client: XXXXXXXXX, server: test.local, request: "GET index.php/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL,,/ HTTP/1.1", upstream: "fastcgi://127.0.0.1:9024", host: "test.local" When checking the code in the debugger, the following call does never return (in ´Varien_Image_Adapter_Abstract::getMimeType()` # $this->_fileName is http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif` # $_SERVER['REQUEST_URI'] = http://test.local/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL list($this->_imageSrcWidth, $this->_imageSrcHeight, $this->_fileType, ) = getimagesize($this->_fileName); The filename requests is an URL to the same server which is requesting the script a link to a static .gif that is not existing. Sample URL: http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif When the above line executed, any subsequent request to the NGNIX server does not respond any more. After waiting for around 10 minutes, the NGINX server starts answering requests again. I tried to reproduce the error with a simple test script that only calls getimagesize() with the given URL - but this not crash. It simple leads to an exception saying that the URL could not be loaded (which is fine as the URL is wrong)

  Read the article

• Home Network Stopped Working

  - by James

  I have a home network where a machine running Windows 7 Ultimate N acts as a central hub for other devices to access media. This has been running for around 2 years now and there has been no recent configuration changes. The machine has a static IP address (192.168.0.3), which also has not been changed. A few laptops, Sonos music system and mobiles are using the machine for music/video mostly. Additionally, post 3389 was also open for RDP. I used a no-ip agent to map a hostname so I could RDP to the machine from the internet. As of yesterday when I try to ping the machine, I get PING:Transmit Failed, General Error I noticed however, the IP it is pinging is 0.0.2.233. All shares etc are no longer functioning including RDP. On the machine itself, an IP config shows like nothing has changed. It still shows the expected IP. If I ping itself from its hostname, I get the same error as above. machine has been rebooted, the router has been also. Any ideas where to even start on this?

  Read the article

• How to deal with ssh's "WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED!"?

  - by Vi.

  I often need to login to multiple remote stations that are just placed to the same static IPs for me. SSH complains about changed keys in this case: $ ssh [email protected] @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ ... Offending RSA key in /home/vi/.ssh/known_hosts:70 ... I usually just run vim /home/vi/.ssh/known_hosts +70, dd wq and re-run the SSH command. How to do it simpler? Requirements: The warning should be displayed, and not like this: The authenticity of host '172.1.2.3 (172.1.2.3)' can't be established. It is easy to accept the key change. I expect something like this: $ ssh [email protected] @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ ... The fingerprint for the RSA key sent by the remote host is 82:cd:be:7a:ae:1b:91:2c:23:c1:74:4d:8a:38:10:32. Change the host key in /home/vi/.ssh/known_hosts (yes/no)? yes Warning: Changed host key for '172.1.2.3' (RSA) in the list of known hosts. [email protected]'s password: Simple and differs from usual "The authenticity of host can't be established." message.

  Read the article

• OpenVPN + iptables / NAT routing

  - by Mikeage

  Hi, I'm trying to set up an OpenVPN VPN, which will carry some (but not all) traffic from the clients to the internet via the OpenVPN server. My OpenVPN server has a public IP on eth0, and is using tap0 to create a local network, 192.168.2.x. I have a client which connects from local IP 192.168.1.101 and gets VPN IP 192.168.2.3. On the server, I ran: iptables -A INPUT -i tap+ -j ACCEPT iptables -A FORWARD -i tap+ -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.2.0/24 -o eth0 -j MASQUERADE On the client, the default remains to route via 192.168.1.1. In order to point it to 192.168.2.1 for HTTP, I ran ip rule add fwmark 0x50 table 200 ip route add table 200 default via 192.168.2.1 iptables -t mangle -A OUTPUT -j MARK -p tcp --dport 80 --set-mark 80 Now, if I try accessing a website on the client (say, wget google.com), it just hangs there. On the server, I can see $ sudo tcpdump -n -i tap0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on tap0, link-type EN10MB (Ethernet), capture size 96 bytes 05:39:07.928358 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 558838 0,nop,wscale 5> 05:39:10.751921 IP 192.168.1.101.34941 > 74.125.67.100.80: S 4254520618:4254520618(0) win 5840 <mss 1334,sackOK,timestamp 559588 0,nop,wscale 5> Where 74.125.67.100 is the IP it gets for google.com . Why isn't the MASQUERADE working? More precisely, I see that the source showing up as 192.168.1.101 -- shouldn't there be something to indicate that it came from the VPN? Edit: Some routes [from the client] $ ip route show table main 192.168.2.0/24 dev tap0 proto kernel scope link src 192.168.2.4 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.101 metric 2 169.254.0.0/16 dev wlan0 scope link metric 1000 default via 192.168.1.1 dev wlan0 proto static $ ip route show table 200 default via 192.168.2.1 dev tap0

  Read the article

• Would a PHP application benefit from being served from a RAM drive?

  - by Tom Marthenal

  I am in charge of hosting a PHP application that is large and slow, but easy to scale. The application is entirely static, with writable disk storage needed. We've profiled the application, and the main bottleneck appears to come from loading the application and not the work the application does. The application is not CPU-intensive, although it does use a fair amount of memory (think Magento). Currently we distribute it by having a series of servers with the same PHP files on their hard drive and a load balancer in front of them. Easy but expensive. I've been reading about RAM disks and the IO benefits they offer, and was wondering if they would be well-suited to PHP applications. Since PHP applications are loaded from disk for every request and often involve lots of different files (as opposed to being kept in memory like with a Java application), I would figure that disk performance can be a severe bottleneck. Would placing the PHP files on a RAM disk and using the mount point as Apache's document root offer performance benefits? A startup script could create the RAM drive and then copy the files (which are plain-text and small) from a permanent location to the temporary RAM drive. Does this make sense, or should I just trust the linux kernel to cache the appropriate files in memory by itself?

  Read the article

• Trying to Set up SMTP Server on WIndows Server 2012

  - by datc

  I'm working on a website, and I need to test the functionality of sending email messages from ASP.NET, something like this: Dim msg As New MailMessage("email1", "email2") msg.Subject = "Subject"<br> msg.IsBodyHtml = True<br> msg.Body = "Click <a href='site'>here</a>." Dim client As SmtpClient = New SmtpClient() client.Host = "My-Server"<br> client.Port = 25<br> client.DeliveryMethod = SmtpDeliveryMethod.Network<br> client.Send(msg) This is running from a Windows 8 workstation. I've installed SMTP server on my Windows Server 2012 machine. The mail shows up in the mailroot/Queue folder and sits there, eventually getting deposited into Badmail. Now I have AT&T U-verse at home, and a few devices connected to the gateway, including let's call it "My-Server." When I run SmtpDiag from say, datc@... to [email protected] I get SOA serial number match passed, Local DNS (99-135-60-233.lightspeed.bcvloh.sbcglobal.net) & Remote DNS (hotmail.com) tests *not* passed, and ultimately, Connecting to the server failed. Error: 10060. Failed to submit mail to mx2.hotmail.com error. When I set My-Server's IP to static and equal to the external IP, 99.135.60.233, and again run SmtpDiag, I get SOA, Local DNS, and Remote DNS tests passed, but the same 10060 error. Same for yahoo.com, gmail.com, and so forth. Is it my ISP's job to fix this? Some PTR record missing somewhere? Is it at all possible to have a home-based SMTP server? All I want is to test my email code. Perhaps, my IP address is just not "trusted" somehow. Thanks.

  Read the article

• How do I enable Ubuntu Gnome system tools

  - by RussellW

  I am running Ubuntu 10 with Gnome 2.30.2. This is a VMWare workstation image provided by another company that I do not have support in this regard. I am trying to access the graphical tools for configuring the network, users, and services but the System-Administration menu does not have these options listed. The main issue I am trying to solve is to correct the problems with the gnome menu options and network settings I have the gnome-system-tools package installed, and I am unable to run command-line versions of the tools, such as nm-applet (I get no GUI if I run that command, the process is running in the background). I realize that I can perform many tasks command-line, but I would like to use the GUI for administrative functions as I am not overly proficient for all command for restarting services and setting a static IP with a specific gateway. Further, I can run gnome-nettool, but I cannot change the IP, I can only see my network card. nm-connection-editor does not show any network cards that I can configure to change the IP. Currently, I am getting a DHCP through my NAT in VMWare, I want to set it to a specific IP address though. Preferences Menu (note some missing options) ![Preferences Menu][1] Admin Menu (note some missing options) ![Admin Menu][2] Network Tools (I can view but not change IP address) ![Network Tools][3] Network Settings (Unable to change IP address) ![Network Settings][4] Network Connections (no connections listed, not even my existing ethernet NAT connection through VMWare) ![Network Connections][5] See images here that I have referenced: 1- http://i.imgur.com/kl8pP.png 2- http://i.imgur.com/K3Cjz.png 3- Iq7Xb.png 4- 7wheV.png 5- J2ad8.png

  Read the article

• Nginx + PHPBB3 reverse proxy images problem

  - by siberiano

  Hello all I have a problem with my Nginx Frontend + Apache2 backend + PHPBB3 software. It doesn't load the CSS and the images neither. I get constant errors like these: 2010/04/14 16:57:25 [error] 13365#0: *69 open() "/var/www/foo/styles/styles/coffee_time/theme/large.css" failed (2: No such file or directory), client: 83.44.175.237, server: www.foo.com, request: "GET /styles/coffee_time/theme/large.css HTTP/1.1", host: "www.foo.com", referrer: "http://www.foo.com/viewforum.php?f=43" This is my config of the site: server { listen 80; server_name www.foo.com; access_log /var/log/nginx/foo.access.log; # serve static files directly location ~* ^.+.(jpg|jpeg|gif|css|png|js|ico)$ { access_log off; expires 30d; root /var/www/trasteando/; } location / { root /var/www/foo/; index /var/www/foo/index.php; } # proxy the PHP scripts to predefined upstream .apache. # location ~ .php$ { proxy_pass http://apache; } location /styles/ { root /var/www/foo/styles/; }

  Read the article

• Nginx Config - I can't access WordPress admin area

  - by WebDevDude

  I am a complete noob when it comes to Nginx, but I'm trying to make the switch over for my WordPress site. Everything works, even the permalink, but I can't access my WordPress admin directory (I get a 403 error). I have my WordPress install in a subfolder, so that complicates things a bit for me. Here is my Nginx config file: server { server_name mydomain.com; access_log /srv/www/mydomain.com/logs/access.log; error_log /srv/www/mydomain.com/logs/error.log; root /srv/www/mydomain.com/public_html; location / { index index.php; # This is cool because no php is touched for static content. # include the "?$args" part so non-default permalinks doesn't break when using query string try_files $uri $uri/ /index.php?$args; } location /myWordpressDir { try_files $uri $uri/ /myWordpressDir/index.php?$args; } location ~ \.php$ { include /etc/nginx/fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /srv/www/mydomain.com/public_html$fastcgi_script_name; fastcgi_split_path_info ^(/myWordpressDir)(/.*)$; } location ~* ^.+\.(ogg|ogv|svg|svgz|eot|otf|woff|mp4|ttf|rss|atom|jpg|jpeg|gif|png|ico|zip|tgz|gz|rar|bz2|doc|xls|exe|ppt|tar|mid|midi|wav|bmp|rtf)$ { access_log off; log_not_found off; expires max; } }

  Read the article

• Locked out of our Comcast Business Gateway for seemingly no reason

  - by Tyler

  A little backstory... Last fall we migrated our ISP from AT&T to Comcast at one of our offices. At that time, we received a new modem/router from Comcast and we configured everything to our liking. We've never really had very many issues with the router aside from having to restart it every once in a while. Here's the problem... About three months ago I changed the password on the router from the default. After that, I logged into the router several times to make changes with no issue. During May I logged into the router to add two new static routes, no problems. A week ago, I tried to log into the router and could not. I tried the non-default password that I changed it to, the default, anything and everything I could think of and no luck. I restarted the router on Monday thinking it may just be locked up, but after the restart it would still not let me log in. This router is at our other office about 2 hours from here and I want to avoid having to drive down there and reset to factory defaults, reconfigure, etc. Any ideas?

  Read the article

• Cisco IOS ACL: Don't permit incoming connections just because they are from port 80

  - by cjavapro

  I am going much based on my memory and I may not be correct on all of this. On a Cisco 851 (IOS) that uses a BVI or a bridge-route (the servers on the inside are configured with static and public IP addresses). I would apply two access lists (both end with deny ip any any log) on FastEthernet4 (the WAN port). There would be one for FA4 in and another for FA4 out. FA4 out would have a line like access-list 110 permit 98.76.54.0 0.0.0.255 gt 1023 any eq http I think this means from 98.76.54.* with a from port of at least 1024 can connect to any other machine with a destination port 80. So, then I have to allow the response to the HTTP connection. FA4 in would have a line like access-list 120 permit any eq http 98.76.54.0 0.0.0.255 gt 1023 Now the problem with that is that anybody on the outside can set their from port to port 80 and then connect to any inside port that is at least 1024. How do we prevent this and require the incoming data to be a response to the outgoing data.

  Read the article

• Router that allows custom Dynamic DNS server [closed]

  - by Thuy

  I've made my own DDNS service and it works fine using an application running on clients to update the IP. But if for some reason I don't have the choice of using my software and instead I need to use a router to update the IP, it becomes troublesome. For example, I needed to setup IPsec from a customer to me and the customers router/firewall (netgear srx5308) has a dynamic IP which is given from the ISP which can't offer static IPs. So it needs to use dynamic dns for it to work. In this case there really isn't a client to run the software on since it's a router/firewall. Unfortunately it seems that most routers are rather unfriendly towards custom DDNS solutions and most offer only dyndns.com or similar templates. Which was the case with this router too. Leaving me with no way to use my own dynamic dns server IP. I have the option of switching out the customers router and I've been looking around for alternatives and other routers/solutions and I was wondering if anyone on this great site might have been in a similar situation or might just know about some router/firewall that is more friendly towards custom ddns solutions that I might be able to use. Thanks in advance for any help or guidance!

  Read the article

• Issue with SSH on Ubuntu - Local connection ok, remote connection - Is it me or my ISP?

  - by Benjamin

  I have an issue with a server running Ubuntu 12.04, I am trying to set up a remote connection so I can access the server at my work from out of town. I have installed the SSH server and all that stuff, and I have reassigned the default port from 22 to 3399. A local connection from any OS can connect on the 192.168... address, but in no way can I get a connection on the actual IP address. I believe my configuration is correct, and I will attach it. If I have done something wrong in the config, please tell me and I will make a change to it. I honestly think that the Router that my ISP provided is horrible, and although the port for ssh is forwarded, it might be stopping any traffic coming inbound. Is there anything I can try to verify this? /var/log/auth does not show any error when I connect VIA our static IP. I have included all values not commented out below: (sshd_config) Port 3399 ListenAddress 0.0.0.0 Protocol 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key HostKey /etc/ssh/ssh_host_ecdsa_key UsePrivilegeSeparation yes KeyRegenerationInterval 3600 ServerKeyBits 768 SyslogFacility AUTH LogLevel INFO LoginGraceTime 120 PermitRootLogin yes StrictModes yes UseDNS no RSAAuthentication yes IgnoreRhosts yes RhostsRSAAuthentication no HostbasedAuthentication no PermitEmptyPasswords no ChallengeResponseAuthentication no PasswordAuthentication yes GSSAPIAuthentication no X11Forwarding yes X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server UsePAM yes Am I doing this wrong? port forwarding image

  Read the article

• Why domain.com appears as theplant.com when hosted on hostgator?

  - by silow

  I have a script that's supposed to detect the url of its caller website. If the caller is another website, it should give something like http://callersite.com. I'm using this line of php code (though I suspect this won't matter for sysadmins) gethostbyaddr($_SERVER['REMOTE_ADDR']) I'm testing with a caller site that's hosted on hostgator. What I'm noticing though is that I don't get callersite.com, I get something like 1a.12.12ab.static.theplanet.com. I don't know what theplanet.com is and why I'm not getting caller site.com. Also what do I need to do to really get the domain of the site making a call to my script? -- Thanks for the explanation. Some have advised I use $_SERVER['HTTP_REFERER'] but it's not what I'm after. My script acts as an API. Another website makes a curl request to it and gets an output and later on presents it to the user. So http referrer gives false since the caller site.com is making a direct call to me. So any hope?

  Read the article

• How do I setup an Alias on Apache with XAMPP on Linux ? (Permission problem)

  - by knarf

  XAMPP works fine but I want to have http://localhost/f to point to /home/knarf/prog/php/fwyxz. I've chmod -R 777 /home/knarf/prog/php/fwyxz I've added Alias /f /home/knarf/prog/php/fwyxz at the end of the httpd.conf And when I try to access it, I get a 403. From the apache error_log: [error] [client 127.0.0.1] (13)Permission denied: access to /f denied. I've already tried several solutions (userdir and symlinks) but they both failed with the same error. I've also tried to add this after the Alias: <Directory "/home/knarf/prog/php/fwyxz"> Order allow,deny Allow from all </Directory> But again, permission denied. Now if I change the User/Group under which apache runs from nobody to knarf, it seems to work (static files are ok) but PHP can't use/initialize sessions : [error] [client 127.0.0.1] PHP Warning: session_start() [function.session-start]: open(/tmp/sess_r5nrmu4ugqguqqe83rs53lq6k0, O_RDWR) failed: Permission denied (13) in /home/knarf/prog/php/fwyxz/index.php on line 3 [error] [client 127.0.0.1] PHP Warning: Unknown: open(/tmp/sess_r5nrmu4ugqguqqe83rs53lq6k0, O_RDWR) failed: Permission denied (13) in Unknown on line 0 [error] [client 127.0.0.1] PHP Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct () in Unknown on line 0 This is really frustrating.

  Read the article

< Previous Page | 421 422 423 424 425 426 427 428 429 430 431 432  | Next Page >