Search Results

Search found 22903 results on 917 pages for 'network namespace'.

Page 430/917 | < Previous Page | 426 427 428 429 430 431 432 433 434 435 436 437  | Next Page >

• DHCP Server on local machine

  - by EralpB

  Hello I am trying to setup a dhcp3-server on Ubuntu. But my question is more generic, if dhcp server is in a blockbox and all clients are connected to it I think I get what is going on but when dhcp server is installed on one of the "clients" that confuses me. When I send a dhcp packet from that client to the dhcp server, will my ethernet card read and write at the same time? Or will it handle it internally without writing any data to ethernet cable. It's the first time I am encountering these network things so I am a little bit confused. Also I wonder If I am in a big network with lan IP let's say 192.168.0.100 and I install a dhcp server to my computer, can any other computers accidentally get IP from my dhcp server? Every computer has one ethernet card (if that matters?). And every computer is connected to one router. I guess the answer is no because the broadcast message won't reach to my computer since when router receives a dhcp search packet it will answer and it won't let other computers know about it because they don't need to. And without router sending that packet one by one, it cannot travel further. I'd be glad if someone enlightens me. Thank you very much.

  Read the article

• BGP Multihomed/Multi-location best practice

  - by Tom O'Connor

  We're in the process of designing a new iteration of our network where we improve resilliency by adding a second datacentre. We'll be adding a second datacentre, with an identical configuration of servers as our primary location. To achieve network connectivity, we're looking into a couple of possible methods. See earlier questions http://serverfault.com/questions/86736/best-way-to-improve-resilience and http://serverfault.com/questions/101582/dns-round-robin-failover-and-load-balancing I'm pretty convinced that BGP is the right way to go about this, and this question is not about RRDNS. 1) If we have 2 locations, do we announce the same IP address block from both locations? 2) If we did this, but had a management ssh interface on x.x.x.50 from datacentre A, but it was on x.x.x.150 in datacentre B. What is the best practice mechanism for achieving this? Because if I were nearest to A, then all my traffic would go to x.50, but if i attempted to connect to x.150, I'd not be able to connect, because this address wouldn't be valid at A, but only at B. Is the best solution to announce 2 different netblocks, one at each location, facilitating the need for RRDNS, or to announce a single block, and run some form of VPN between the two sites for managment traffic?

  Read the article

• How do I diagnose a bottleneck in an Intel Atom based Ubuntu server?

  - by Jon Cage

  I have a small media server at home which has software raid and a gigabit link to the rest of my network. For some reason though, I only get ~10MB/s transfers when copying to/from the server. I use software RAID5 (mdadm) over 4 1TB disks. On top of that I then use LVM to give me a huge pool of disk space which is then split up into multiple partitions which can be resized as and when they need it. I'm guessing this it most likely the cause, but I'd like to know for sure where the root cause is. So, how can I benchmark network throughput (Windows 7 desktop <- Ubuntu server) and hard disk performance to try and identify where my bottleneck might be? [Edit] If anyone's interested, the motherboard is an Intel Desktop Board D945GCLF2. So that's a 300 series Atom processor with the Intel® 945GC Express Chipset [Edit2] I feel like such a fool! I just checked my desktop and I had the slower of the two onboard NICs plugged in so the server is probably not at fault here. Transferring a copy of ubuntu off the server I get ~35-40MB/s according to Windows 7. I'll do those HD tests when I get a chance though (just for completeness).

  Read the article

• Two NIC's 2 Internet Connections, 1 Windows Server 2008 RC2, Routing help required

  - by PJZ

  Hello, I have a Windows 2008 server and 4 other client machines on my home network. I have two internet connections. The main connection is setup with a home router and DHCP on that for all the clients on the network. The secondary connection is just a cable modem which is plugged directly into the server. Local Area Connection: This NIC has an external IP and is connected to the Cable Modem. Local Area Connection 2: This NIC has an internal IP (192.168.0.102) and allows access to all the internal computers. It also has internet access via the local router. So here lies the problem, I want to use the Cable connection on the server for the internet traffic (so that the traffic for server/clients are seperated) but I also need to maintain local access. I am wondering how to make it so that all the internet traffic goes via that NIC because at the moment it goes through the local NIC. As a secondary problem I would also like to forward the connection of one application used by the clients via the server and the cable/server internet because of poor routing for it on the main connection. This perhaps is something for another question though. Thanks for any help you can offer me. Regards PJ

  Read the article

• How can I get my routers to forward ports correctly?

  - by Giffyguy

  My network currently looks like this (simplified): Note that Router #2 is connected to the LAN interface of Router #1. This should be familiar to anyone who has seen a standard static-IP setup with an additional firewall for a residence or other small building. Router #1 is actually my cable gateway, but since it is a fully functional router/firewall, I am going to refer to it as a router. Now, I need to open various ports in both firewalls for incoming communication to my server - port 80 is a good example. So I've opened up port 80 in Router #2, and so far all incoming traffic at the public IP X.X.X.129 is being routed correctly. The problem is that I also need my server to respond to incoming traffic at the public IP X.X.X.130 on the WAN interface of Router #1. Naturally, I can't just tell Router #1 to forward port 80 to another public IP. Port forwarding is only supported when the traffic is being directed to the LAN subnet. I am willing to restructure my network topology if required, with the following conditions: Router #1 cannot have its WAN IP reassigned - X.X.X.130 is mandatory. Router #1 cannot be moved or disconnected from the cloud. The server cannot be given a second IP address. I would prefer the server to have a private IP address - e.g. 10.0.0.10 I'd like to keep Router #2, but it can have a private IP - e.g. 10.0.1.10 Following these rules, I need to get my server to receive incoming traffic on port 80 from both public IP addresses. Does anyone on SU know if this is possible? So far my only theories have been to set up a static route on either router, or to somehow combine my two subnets into a single subnet.

  Read the article

• Replacing local home server with VPS: Suggestions?

  - by CamronBute

  So right now, I'm running an old box with a 2TB HDD in it. I use this as a file server for the home network, as well as a box for downloading large files which are synced via Dropbox. Lots of other tinkering things, too. Basically, I'm sick of paying extra for the power and having to worry about drive failures and whatnot. I'd rather get a remote server, let someone else manage it and provide access from the Internet. So, I've been looking for a Windows VPS that would give me access to install things and tinker, and I'm having a problem finding a host that offers more than 100GB of hard drive space. If they do offer a package with 100GB of storage, everything else is waaayyyy more than what I actually need. The idea is to create a permanent VPN connection from the cloud server to my home network to provide a transparent solution so I'm not having to go to lengths to transfer files or whatnot. I think a VPS solution will allow me to do this. I would like 1TB of storage space, minimum 100Mbps Internet connection, minimum 250GB bandwidth, admin access. Anyone have anything? Or am I being unreasonable? If I am, why?

  Read the article

• I can't connect new Windows 7 PC to Mac iBook with OS 10.3.9

  - by Jeff Humm

  Help ! I have an old iBook wired to a router and a new PC linking wirelessly to same router. On the Mac I have 'seen' the PC but not been able to connect to it. On the PC, the Network and Sharing Centre lists 'IBOOK'. When I click on this, 'Windows Security' asks me to 'Enter Network Password', asking for User name and password. I have tried: 1) The user name and password of my admin account on the iBook. This returns a 'logon failure' message but lists the user name as [NAME_OF_PC\User Name], suggesting it was looking for the user name of the PC, not the Mac. 2) The user name and password of my account on the PC. This also returns a 'logon failure' message. 3) The user name of my account on the PC and the 'homegroup password' given to me by Windows when setting up the PC. This also returns a 'logon failure' message. Today I've tried connecting the two machines via a patch cable - still no joy. Can anyone help? It is 20 years since I wrestled with any OS other than Mac, and 10 years since I've done mich wrangling with the Macs, so please assume no knowledge! Thanks in advance,

  Read the article

• Is "DSLAM congestion" a legitimate reason for slow DSL?

  - by Jay Bazuzi

  My DSL has been extremely slow in the evenings recently. To test it, I telnet to my DSL Modem, and ping the gateway. This way I eliminate internet congestion and local network issues. In the mornings I get 30ms - 50ms pings. In the evenings, it bounces around a lot, but 10000ms pings are common. I complained to Qwest support, and they said it was a known issue on their end, their engineers were working on it, and wouldn't say anything else. A couple days later I complained again, and they sent out a technician. He tested my house wiring and found that one of them had a short. It was an unused line, so we disconnected it, and he said things looked better and left. My daytime speeds improved at this point, but evening is still bad. I complained to Qwest support again, and they said it was a problem with DSLAM congestion at their end, and that they were working on it, but no ETA. My neighbor has Qwest DSL and doesn't seem to have these problems. That seems strange. I go use her network when I absolutely must get online and mine is behaving badly. I can't tell if they're yanking my chain or not. Regardless, these speeds are crap. I'm paying for 7Mpbs but am lucky if I get 1/10th that in the evenings. My kids like to watch Netflix streaming movies, and it's just impossible after 5pm or so. Should I wait it out? Will complaining again produce any results? Should I change my subscription to a lower speed until they fix their end? Or switch to cable?

  Read the article

• How can I use two Internet connections in Ubuntu?

  - by Martin

  My goal is to be able to do something like this: curl google.com --interface ppp0 curl google.com --interface p2p2 ppp0 is a DSL connection, and p2p2 is a separate direct Internet connection. Currently I can only get one of these to work at a time. When I enable one, the other one stops working. /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # DSL auto p2p1 iface p2p1 inet manual auto dsl-provider iface dsl-provider inet ppp pre-up /sbin/ifconfig p2p1 up # line maintained by pppoeconf provider dsl-provider # DIRECT auto p2p2 iface p2p2 inet dhcp ifconfig: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 p2p1 Link encap:Ethernet inet6 addr: fe80::20a:ebff:fe21:99c6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 p2p2 Link encap:Ethernet inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20a:ebff:fe17:1249/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ppp0 Link encap:Point-to-Point Protocol inet addr:53.193.231.167 P-t-P:53.193.224.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 10.0.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 53.193.224.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 p2p2 By default, only ppp0 works. If I run "route add default gw 192.168.1.1 p2p2" then I can use p2p2 but ppp0 stops working. If I then run "route add default gw 53.193.224.1 ppp0" then I can use ppp0 again but p2p2 stops working. What can I do to be able to use both interfaces selectively?

  Read the article

• Connecting to server from remote machine

  - by Jannat Arora

  I wish to connect my machine to a server in some other city. For doing the same I am using the following command: mstsc -v ip_address_of_server remote desktop can't connect to remote computer for one of these reasons: 1) Remote access to server is not enabled. 2) Remote computer is turned off 3) Remote computer is not available on network. Make sure remote computer is turned on and connected to the network, and that remote access is enabled. As per previous posts I need to turn off my client computers firewall..which I have...but still it gives me the same message. Can someone please please help me out...so as to how i may resolve this?? I am really new to networking, etc. Also when i am pinging: ping ip_address_of server I am getting the following response: Reply from ip_address_of_server: destination host unreachable Also I did try on ubuntu with rdesktop...still its not been able to connect with it. Also i know there are other people who are able to connect their machines with the server remotely. So i guess its not working for me only. Also when I accessed the same machine through LAN I was able to do so.

  Read the article

• How can find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• Elevating UAC via .bat file?

  - by jslaker

  Pretty straightforward one that I'm having trouble finding an answer to. serverfault previously helped me with finding a way to automate Windows updates without using WSUS. It's working fantastically, but to run it over the network, you have to first mount a shared drive. That's pretty simple XP since you just mount the drive and run the updater. On Vista and W7, though, this all has to be done with elevated privileges to work correctly. The UAC account can't see network drives mounted by the regular user, so in order to get everything working, I have to mount the share via net use from an escalated shell. I'd like to automate mounting this share and launching the updater via a simple .bat file. I could probably just instruct everybody to right click "Run as Administrator" on the .bat file, but I'd like to keep things as simple as possible and have the .bat automatically prompt the user to escalate their privileges. Since these computers don't belong to us, I can't count on anything like Powershell being installed, so that rules any solution along those lines out and pretty much have to rely on things that would be included in an RTM Vista install. I'm hoping I'm mostly missing something obvious here. :)

  Read the article

• How to create VHD disk image from a Linux live system?

  - by Federico

  Once more, I have to resort at the experts here at SuperUser, as my other sources (mainly Google ;-)) didn't prove very helpful... So basically, I would like to create a VHD image of a physical disk to be archived/accessed/maybe even mounted in a virtual machine. Now, there are dozens of articles and tutorials on how to do that on the web, but none that meets exactly the conditions I would like to achieve: I would like the destination file to be a VHD image, as Windows 7 can mount it natively, even over the network and many other programs can use it (VirtualBox, ...) The disk I'm trying to image contains a Windows XP install, so in theory, I could use the disk2vhd utility, but I would like to find a solution that doesn't require booting that Windows XP install (ie keep the disk read-only) Thus I was searching for a solution involving some sort of live system (running from a USB stic or the network) However, all the solutions that I've came across either make use of disk2vhd or use the dd command under linux, which does a complete copy of the disk (ie even empty blocks) and does not output a VHD file. Is there a tool/program under Linux that can directly create a VHD file? Or is is possible to convert a raw disk image created using dd to a VHD file, without allocating space for the empty blocks? How would you proceed? As always, any advice or comment is highly appreciated!!

  Read the article

• Inter-VLAN Malicious Code Scanning

  - by Jackthedog

  I am trying to find an inbuilt solution on a Cisco Catayst 3750X Switch to scan all traffic routed from one VLAN to another for malicious code. The situation is that we currently have a development environment which is currently being redesigned to upgrade the network infrastructure to use the 3750X switches to manage server and workstation connectivity as well as inter-VLAN routing. We also have another system that is responsible for taking the builds created on the development environment and imaging various HDDs. Because these are two separate systems, we have a requirement in the workplace to anti-virus scan any data transferred between these systems. This is done by copying the data from the originating system to external USB HDD, scanning in a standalone workstation and then copying the data on to the receiving system. As you can imagine this is extremely tedious and impractical most of the time... (I don't make the rules). Anyway, with this redesign going on, we would like to join the imaging system to the network infrastructure of the development system, keeping separation by the use of VLANs and restricting traffic by using ACLs. As we still have the requirement to scan all traffic I would like to configure some sort of malicious code scanning when ever traffic is routed between these VLANs. I am aware I could install a separate in-line IPS/IDS device, however both systems will be using multiple ports on the switch (obviously), and we won't be able to put a device on each port. I would would prefer not to add additional hardware if the 3750x switch is capable of doing the job. Is anyone aware of any Cisco solution that I could use here, that ideally can be incorporated into the 3750x switch? Thanks in advance.

  Read the article

• How do I prevent or override a group policy on Windows 7?

  - by Kevin

  A few months ago my company was purchased by a large corporation. We recently switched our network over to the large corporate network which has more restrictions requirements. One of these is the requirement to use a proxy server for Internet traffic. However, some of our internal servers are not recognized by the corporate DNS, so we need to provide the fully qualified domain name. For W7, we make changes to the Internet Properties for IE8 and Chrome to include our domain name as an exception to the proxy server (e.g., *.foobar.com). The problem is that a group policy that does not include our domain name is continually pushed out to my systems throughout the day. This requires me to make the appropriate changes to the Internet Properties several times a day in order to access our internal servers. Is there a way that I can prevent the group policy from being pushed to my systems or detect when the group policy is pushed and override it? I am an administrator on all of my systems. I do have Firefox installed which is not subject to the same group policy push, but I need to have IE8 and Chrome working.

  Read the article

• Split Tunnel VPN using incorrect Tunnel

  - by Brian Schmeltz

  Our company has a handful of field offices that have recently been setup with a regular internet connection after we removed the T1 and router that connected them directly to our network. Now, when the users are in the office, they log in to the VPN to be able to connect to the network. For the sake of them being able to print and scan from the local multi-function we have setup a split tunnel VPN. We currently have about 15-20 users using this setup around the country without any problems. Recently one of our users started having problems accessing internal programs/sites when connecting from both home and the office. There are three other users in the same office and they do not have this problem. I assumed that it was something with the computer and went ahead and replaced it with another of the same model. The computer worked fine in our home office; however, when the user received it, she had the exact same problem both at home and in the field office. Thinking it may be a NIC driver issue I sent her another computer, this time a different model, same problem occurred. If I update the host file to point to the correct paths, things will work, and if I connect via a normal VPN connection everything works, but the user cannot scan or print - which is a problem. Have tried to find ways to create another tunnel on a normal VPN and have tried to find ways to force the correct tunnel on the split tunnel VPN. It appears that there is something related to the ISP because if I connect to Comcast or Verizon it is fine but once she connects to Insite then she has problems. I have been unable to get any support from Insite as they don't feel the issue is with them. We use a Nortel VPN client. Any thoughts or ideas would be appreciated.

  Read the article

• Split Tunnel VPN using incorrect Tunnel

  - by Brian Schmeltz

  Our company has a handful of field offices that have recently been setup with a regular internet connection after we removed the T1 and router that connected them directly to our network. Now, when the users are in the office, they log in to the VPN to be able to connect to the network. For the sake of them being able to print and scan from the local multi-function we have setup a split tunnel VPN. We currently have about 15-20 users using this setup around the country without any problems. Recently one of our users started having problems accessing internal programs/sites when connecting from both home and the office. There are three other users in the same office and they do not have this problem. I assumed that it was something with the computer and went ahead and replaced it with another of the same model. The computer worked fine in our home office; however, when the user received it, she had the exact same problem both at home and in the field office. Thinking it may be a NIC driver issue I sent her another computer, this time a different model, same problem occurred. If I update the host file to point to the correct paths, things will work, and if I connect via a normal VPN connection everything works, but the user cannot scan or print - which is a problem. Have tried to find ways to create another tunnel on a normal VPN and have tried to find ways to force the correct tunnel on the split tunnel VPN. It appears that there is something related to the ISP because if I connect to Comcast or Verizon it is fine but once she connects to Insite then she has problems. I have been unable to get any support from Insite as they don't feel the issue is with them. We use a Nortel VPN client. Any thoughts or ideas would be appreciated.

  Read the article

• Windows 7 Multi-NIC woes

  - by Eric

  I have Comcast business Internet here. It gives me 5 static IPs. Most of the machines in my house connect to a router like every other household. It has a 192.168.117.x subnet, DHCP Server, etc. and all is well. However, I have a second machine on MY desk that has a life Internet IP. Up until yesterday, this machine was running XP Pro. The primary NIC was manually set to 192.168.117.241 with no gateway, and the secondary NIC was manually set to 173.x.x.171 with a gateway of 173.x.x.174. This worked just fine for years. Yesterday I replaced that XP machine with a brand new Windows 7 x64 box. Again, I configured it the same way. The onboard NIC was given a static 192.168.117.x address with no gateway, and the secondary NIC was given a live Internet IP address with the proper router, etc. 2 Problems. First is that the internal network (192.168.117.x) is listed as a public network because there's no gateway, so that means no homegroup, no file sharing, none of that. And I can't change it from what I'm reading... The second is that the machine reports the "router" ip address as it's address, and not the address that it's supposed to. I'm ready to tear my hair out over this. Any ideas?

  Read the article

• Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

  - by Bo102010

  (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

  Read the article

• Drive Mapped On Amazon EC2 Instance Startup Disconnected After Logon

  - by jsn

  I am launching an Amazon EC2 instance (Windows Server 2012), and on startup (though User Data field), it runs this powershell script: <powershell> NET CONFIG SERVER /AUTODISCONNECT:-1 # clear all prior connections net use * /delete /y > C:\delLog.txt 2>&1 # mount new drive net use R: \\dbHost\share /user:username pass /persistent:yes > C:\useLog.txt 2>&1 ipconfig /all > C:\ipLog.txt </powershell> When it launches and I connect to it through RDP, it shows in explorer "Diconnected Network Drive (R:). If I double click it, error message displays "R:\ is not accesible. Access id denied". Normally, it would ask me for credentials to reconnect. I need for this drive to be connected through the duration of the instance. delLog.txt contents: You have these remote connections: T: \\dbHost\share Continuing will cancel the connections. The command completed successfully. useLog.txt contents: The command completed successfully. ipLog.txt contents as expected. The net use commands works fine by itself, it connects. Anyone have any idea what could be wrong? There is only one account on these machines - Administrator. It is a samba share to a Linux server on a private network.

  Read the article

• Rapidly changing public IP addresses on certain networks?

  - by zenblender

  I run/develop an online game where many of our users are in southeast asia. I recently went to southeast asia and made an alarming discovery. Anywhere I got internet access, whether it was via 3G, a LAN in a hotel, or wifi in a cafe, both in Singapore and the Philippines, I noticed that my IP address was changing CONSTANTLY. I mean the public IP address, not the private one. I could load a page like whatismyip.com and just hit reload and see a new IP address show up every 5-10 seconds! This has lots of consequences for my online game, as many things "break" if the IP address changes for a given user. Basically, I would like to know more about this. Is there a name for the kind of network or router or paradigm that causes this, so I can read up on it? I don't understand WHY a network would function this way. Does it do this on purpose? Is it for security reasons? Is it to anonymize and protect the identity of the users? Or is it just an "old" method that is mostly obsolete in the rest of the world? Thanks for any info that will help me to understand.

  Read the article

• How to prevent getting infected by rogue security applications

  - by Ieyasu Sawada

  My computer never got infected with a virus before, because I'm using Web of Trust browser plugin, sandboxie and Avast Free antivirus. But today, it got infected with a rogue security application called antivirus.net. I have already removed it using MBAM, SAS, and Kaspersky Virus Removal Tool. And by the way, I was using MSE when my laptop got infected. Seems like the rogue application just killed off the MSE process. And I never even got a warning. I was using the wi-fi from our school, which I think is the cause since most of the computers in our laboratory has rogue applications on it. My question is, how do I prevent this from happening again? It took me about 6 hours to disinfect my computer and I don't want it to happen again. Please enlighten me if these rogue applications really just pop out of nowhere. Note I'm not dumb enough to agree with installing rogue security applications. It just came out of nowhere. I'm happy with MSE, well not after it let antivirus.net penetrate my computer. I've done a little bit of research and it says that it needs the permission of the user to actually install it in the computer: http://www.net-security.org/malware_news.php?id=1245 http://en.wikipedia.org/wiki/Rogue_security_software Is it possible that other computers in our school network have agreed to install those? Or maybe the network admin?

  Read the article

• Connecting to IPv6 hosts when mobile and on a Surface?

  - by Cerebrate

  Specifically, at my usual location, I have an IPv6 network which connects to the Internet via a static tunnel set up to Hurricane Electric's tunnel broker ( http://www.tunnelbroker.net/ ). This works essentially perfectly, allowing inbound and outbound connectivity. Now, however, I need to connect back to host(s) on that network over IPv6 from mobile tablet(s); meaning the conditions are such that there is no guarantee or even likelihood of native IPv6 support where it happens to be at any given time, and the IPv4 address of the tablet will change on a fairly regular basis. The native Teredo support, as configured by default, functions well enough to let me ping my target hosts, but appears to have neither the reliability nor the throughput to support anything else; I have been unable to make any actual connections (trying a number of TCP-based protocols) using it. I had considered setting up an independent tunnel for the tablet(s), and using scripts to update the client endpoint IP address when it changes, but since both (a) many of the locations will be behind NAT devices over which I have no control, and (b) the option over which I do have control is an AT&T Unite hotspot which does not offer protocol 41 forwarding or respond to ICMP on its public address, this approach does not seem viable. I am additionally constrained as the mobile tablet(s) in question are Surface RTs, and as such are incapable of running, for example, AICCU client software. What is my best option to pursue to obtain IPv6 connectivity in this scenario?

  Read the article

• Problems starting autossh on boot [ubuntu]

  - by Ken

  I'm trying to automatically start an SSH tunnel to my server on boot from a ubuntu box. I have an ubuntu box that's mounted on an 18-wheeler and is networked behind an air card. The box hosts a mysql database that i'm trying to have replicated when the aircard is connected. As I can never be sure of my IP and how many or which routers I'm behind I'm connected to my replication server with an SSH tunnel. I got that working using the following command: ssh -R 3307:localhost:3307 [email protected] Now I'd like that to start whenever the box is, and be alive all the time, so I installed auto-ssh and setup this little script: ID=xkenneth HOST=erdosmiller.com AUTOSSH_POLL=15 AUTOSSH_PORT=20000 AUTOSSH_GATETIME=30 AUTOSSH_DEBUG=yes AUTOSSH_PATH=/usr/bin/ssh export AUTOSSH_POLL AUTOSSH_DEBUG AUTOSSH_PATH AUTOSSH_GATETIME AUTOSSH_PORT autossh -2 -fN -M 20000 -R 3307:localhost:3306 ${ID}@${HOST} I've tried putting this scrip in /etc/init.d/ and using a post-up command in /etc/network/interfaces as well as putting it in /etc/network/if-up.d/. In both situations the script starts on boot, but the tunnel doesn't appear to be correctly established. The script works when run manually.

  Read the article

• Why can a local root turn into any LDAP user?

  - by Daniel Gollás

  I know this has been asked here before, but I am not satisfied with the answers and don't know if it's ok to revive and hijack an older question. We have workstations that authenticate users on an LDAP server. However, the local root user can su into any LDAP user without needing a password. From my perspective this sounds like a huge security problem that I would hope could be avoided at the server level. I can imagine the following scenario where a user can impersonate another and don't know how to prevent it: UserA has limited permissions, but can log into a company workstation using their LDAP password. They can cat /etc/ldap.conf and figure out the LDAP server's address and can ifconfig to check out their own IP address. (This is just an example of how to get the LDAP address, I don't think that is usually a secret and obscurity is not hard to overcome) UserA takes out their own personal laptop, configures authentication and network interfaces to match the company workstation and plugs in the network cable from the workstation to their laptop, boots and logs in as local root (it's his laptop, so he has local root) As root, they su into any other user on LDAP that may or may not have more permissions (without needing a password!), but at the very least, they can impersonate that user without any problem. The other answers on here say that this is normal UNIX behavior, but it sounds really insecure. Can the impersonated user act as that user on an NFS mount for example? (the laptop even has the same IP address). I know they won't be able to act as root on a remote machine, but they can still be any other user they want! There must be a way to prevent this on the LDAP server level right? Or maybe at the NFS server level? Is there some part of the process that I'm missing that actually prevents this? Thanks!!

  Read the article

< Previous Page | 426 427 428 429 430 431 432 433 434 435 436 437  | Next Page >