Search Results

Search found 18142 results on 726 pages for 'wcf configuration'.

Page 432/726 | < Previous Page | 428 429 430 431 432 433 434 435 436 437 438 439  | Next Page >

• dynamic routing between openvpn tunnels

  - by pQd

  i'm thinking about using dynamic routing [ OSPF or RIP ] via OpenVPN tunnels. right now i have few offices connected in full mesh, but this is not scalable solution as we add more locations. i would like to avoid situation when plenty of internal traffic is affected if one of two vpn termination points that i plan to use is down. do you have similar configuration working in production? if so - what routing daemon did you use - quagga? something else? did you encounter any problems? thanks!

  Read the article

• virtualbox, MAAS: help needed

  - by Roberto Attias

  Ok, I made some progress wrt the original question (still below). I found /etc/maas/dhcpd.conf contained option domain-name-servers 10.0.3.15, and changed it to 192.168.0.11. After restarting the daemon, I now see "node" getting the right DNS, unfortunately this doesn't fix the main problem, which I believe is the reference to 169.254.169.254. It does introduce a new question: while the remaining information from /etc/maas/dhcp.conf is present in the maas GUI, there is no field to enter the dns address. Why? Anyway, my original problem still stands... Any idea? Original question follows. In VirtualBox, I have: master VM: ubuntu 12.04.3 server eth0: Internal Network, IP= 192.168.0.11 eth1: NAT, IP= 10.0.3.15 eth2: Host-only, IP= 192.168.56.102 running MAAS region and cluster controlller, with DHCP and DNS enabled node VM: eth0: Internal Network node VM boots in PXEboot. DHCP succeeds, and the boot process starts, but during boot I see some issues. One of them is "disk drive not ready yet or not present" for / and /tmp. I've googled this issue, and some people say it happens when the fisical disk is a SSD, which is my case. Anywaythe system seems to recover from this eventually. Immediately after it starts printing a lot of messages of the form: 2013-10-01 16:52:37,142 - url_helper.py[WARNING]: Calling 'http://169.254.168.254/2009-04-04/meta-data/instance-id failed [x/y]: url error [[Errno 113] No route to host] That IP address is clearly bogous, not sure where it came from. Before that point, I had seen the following network configuration: address: 192.168.0.100 broadcast: 192.168.0.255 netmask: 255.255.255.0 gateway: 192.168.0.1 dns0 : 10.0.3.15 dns1 : 0.0.0.0 Not sure if related, but the dns doesn't seem right, as node doesn't have an interface to reach 10.0.3.15. If that's the problem, what should I change to have the DNS point to 192.168.0.11? Thanks, Roberto

  Read the article

• Minimizing SQL transaction log file size on developer box running simple recovery model

  - by Anders Rask

  We have alot of SQL servers on development environment where we never take backup of the databases (TFS for code is enough). The (SharePoint) databases are all set to simple recovery model, but the log files, especially for the SharePoint configuration database is growing quite large and filling up our data drive on the SQL server. Since these log files are never used for anything, i would like advice on how to best minimize the size of these log files -or even disable them if possible. I'm not completely sure why the log files grow so large even on simple logging (checked for long running transactions (DBCC OPENTRAN) but found none). I guess the reason for the log files not being truncated is, that we dont take any backups, and hence Checkpoints arent reached. The autogrowth for log files are set to autogrow by 10% restricted to 2 gb, so i guess that is why Checkpoint (70%) arent reached here either. What would be the be best strategy to keep log files small (best case 0) without sacrificing performance (eg VLF fragmentation)?

  Read the article

• Need reccomendation for transferring ASP.NET MVC skills to PHP

  - by Tuck

  I am looking to translate my skills in .NET to PHP - specifically in regards to ASP.NET MVC. At work I am currently using .NET MVC 2.0 on a variety of projects and thoroughly enjoy the platform. Specifically I enjoy the very minimal configuration required to get a project up and running (just create the project, define routes, and start coding), as well as the ability for controller actions to return different items (i.e. ActionResult, JsonResult). Another piece I really like is the way the view/model interaction can be handled. For example I like being able to call return View(model) and having a view page (.aspx) load and having the full model object available to the view, regardless of the model type. I'm looking for a PHP implementation of MVC that is the most similiar to what I am already familiar with. I don't anything apart from the MVC functionality. I've looked at Zend, Symfony, CodeIgniter, etc. and, while they look like they'll be fun to play with in the future, they provide much more functionality than I need. I'd prefer to write my own DAL,form helpers, delegate handlers,authentication/ACL pieces, etc. In short, I just need something to handle the routing and view interactions and will worry about the model implementation myself. Can someone please point me to some lightweight code that accomplishes or comes close to accomplishing my objectives above. Or, can someone identify just the portions of a larger framework that do the same (again, I'm not currently interested in implementing something on a big framework, just the MVC portion and want to implement the model portion myself as much as possible). Thanks in advance...

  Read the article

• Confused about SPF Record setup

  - by Ramon A.

  Hello, I'm confused on how I should set up SPF records for my multiple domains. Here is my configuration: the setup is: (a) domain1.com points to server1 (b) mail.domain1.com points to server2 (c) domain2.com is a vhost in server1 (d) domain3.com is a vhost in server1 (e) and so on.. I want the SPF record to be set up so that domain1.com, domain2.com, domain3.com are authorized to send emails using mail.domain1.com. I'm confused on wether to put the SPF record on each domain, or on the main server only.

  Read the article

• Windows 8.1 Enterprise Sysprep Error

  - by Anurag Shetti

  I am Trying to sysprep my WIndows 8.1 enterprise (MSDN) and i get the following errors I have upgraded the Windows 8 to windows 8.1 and the machine contains all the configuration for VS 2012 and rest Exact error Sysprep was not able to validate your windows installation Error msg line in log C:\Users\André>err 0x8007139f # as an HRESULT: Severity: FAILURE (1), FACILITY_WIN32 (0x7), Code 0x139f # for hex 0x139f / decimal 5023 ERROR_INVALID_STATE winerror.h # The group or resource is not in the correct state to # perform the requested operation. # 1 matches found for "0x8007139f" SYSPRP ActionPlatform::GetValue: Error from RegQueryValueEx on value SysprepMode under key HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Setup\Sysprep; dwRet = 0x2 I have searched the HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Setup\Sysprep But i coud'nt find anything for SYSprep mode The value for sysprep was (Value not set)

  Read the article

• Is there a good dual monitor arm solution for iMac 27" i7s?

  - by Darren Newton

  I currently have an iMac 27" and am considering purchasing another to run in target display mode. My desk space is a little limited. Is there a dual monitor arm solution that can support the weight of two iMac 27" units (30.5 pounds (13.8 kg)) as well as their width (25.6 inches (65.0 cm)) in a side-by-side landscape configuration? I looked at the Ergotron LX Dual Side by Side but the iMacs appear to exceed the width and weight limit this device is rated for. I'm open to alternate solutions to arms, such as a multi-unit desk stand/mount, but a wall mount is not possible for me at this time. Thanks!

  Read the article

• How to tell if mod_deflate is actually working?

  - by Jayraj

  I have put the following in my http.conf file: # mod_deflate configuration <IfModule mod_deflate.c> # Restrict compression to these MIME types AddOutputFilterByType DEFLATE text/plain AddOutputFilterByType DEFLATE text/html AddOutputFilterByType DEFLATE application/xhtml+xml AddOutputFilterByType DEFLATE text/xml AddOutputFilterByType DEFLATE application/xml AddOutputFilterByType DEFLATE application/x-javascript AddOutputFilterByType DEFLATE text/javascript AddOutputFilterByType DEFLATE text/css # Level of compression (Highest 9 - Lowest 1) DeflateCompressionLevel 9 # Netscape 4.x has some problems. BrowserMatch ^Mozilla/4 gzip-only-text/html # Netscape 4.06-4.08 have some more problems BrowserMatch ^Mozilla/4\.0[678] no-gzip # MSIE masquerades as Netscape, but it is fine BrowserMatch \bMSI[E] !no-gzip !gzip-only-text/html <IfModule mod_headers.c> # Make sure proxies don't deliver the wrong content Header append Vary User-Agent env=!dont-vary </IfModule> </IfModule> My content doesn't return with a Content-Encoding of type gzip, but I find myself getting a lot more 304s and the Etag is appended with a +gzip suffix. Is mod_deflate actually doing its job? (Sorry about the n00b-ishness)

  Read the article

• low-cost RAID NAS for home use?

  - by gravyface

  Have a noisy, power-hungry Pentium 4 based Ubuntu server that I want to replace with a nice, low-power mini-ITX/Intel Atom-based machine to do my network services (DHCP, DNS, IPSec, Web/mail, FTP, etc.) and am thinking of a (hopefully) equally-low powered NAS using NFS over GbE with at least 1 TB space and a RAID 5 (preferred) or RAID 0 (likely) configuration for redundancy with a couple of spare disks I can swap in as needed down the road. Would I be better off getting a full sized ATX mobo/case and configuring the RAID internally? I really want to keep power consumption down as much as possible as I leave my home server up 24/7.

  Read the article

• low-cost RAID NAS for home use?

  - by gravyface

  Have a noisy, power-hungry Pentium 4 based Ubuntu server that I want to replace with a nice, low-power mini-ITX/Intel Atom-based machine to do my network services (DHCP, DNS, IPSec, Web/mail, FTP, etc.) and am thinking of a (hopefully) equally-low powered NAS using NFS over GbE with at least 1 TB space and a RAID 5 (preferred) or RAID 0 (likely) configuration for redundancy with a couple of spare disks I can swap in as needed down the road. Would I be better off getting a full sized ATX mobo/case and configuring the RAID internally? I really want to keep power consumption down as much as possible as I leave my home server up 24/7.

  Read the article

• Urgent :The desktop currently has no desktop sources

  - by vDeepak

  Although i know there are large no. of post already floating over same issue , but am having no luck so far. I am getting below error message when trying to connect desktop by vmware view client 4: "the desktop currently has no desktop sources............. " My configuration is listed below: using view manager server over VM box. successully deployed 10 desktop VM over View manager and they are persistent mode. previoulsy few users were able to coonect to these desktops successfully under desktop sources i am getting "Domain name\user ID" and under status its showing "Ready" So when any other user who is authenticated trying to access desktop getting above mentioned error message. The other users are unique one who previously never logged in. Also i tried to rebooth the VM desktops assuming they might be locked by another user , but still am getting the same error message. Please help.

  Read the article

• How can I do Ubuntu Lucid Desktop installation with HTTP preseed?

  - by netvope

  Installation media: ubuntu-10.04-desktop-i386.iso I tried a lot of different boot parameters, but either the installer ignored the preseed configuration, or it boot itself directly as LiveCD. An example of the boot parameters I've tried: auto url=http://mydomain.com/path/preseed.cfg boot=casper only-ubiquity initrd=/casper/initrd.lz quiet splash -- If I remove only-ubiquity, it boots as a LiveCD. If I remove boot=casper, it won't boot. If I add vga=normal locale=en_US console-setup/layoutcode=us console-setup/ask_detect=false interface=auto, it still can't do automatic install. If I remove auto, it's the same. What is the correct boot parameters for launching such an installation? From the apache log of the server hosting preseed.cfg, I see that the installer has no problems fetching the preseed file. My preseed file is almost identical to the one at https://help.ubuntu.com/10.04/installation-guide/example-preseed.txt. Moreover, I have run debconf-set-selections -c preseed.cfg to ensure that the preseed file is correct.

  Read the article

• mono: application not running when web.config in subfolder

  - by Quandary

  I run asp.net on mono. I wanted to run blogengine: http://www.dotnetblogengine.net/ I downloaded, put it in /var/www/blogengine, on the console went to /var/www/blogengine and started xsp2. I went to http://localhost:8080, and it ran without problems. Then I stopped xsp2, went to /var/www and started xsp2. I went to http://localhost:8080/blogengine It ended with a strange error: The section <blogProvider> can't be defined in this configuration file (the allowed definition context is 'MachineToApplication'). (/var/www/blogengine/Web.Config line 9) The problem seems to be that it stops working as soon as the xsp2 root folder is anything else than the application root folder... Do I have to config anything ? Or what else is wrong ?

  Read the article

• How do I get a Dane-Elec mp3/mp4 player working?

  - by user40432

  My MP3/MP4 does not plug-in and play and therefore I can not transfer any file to the MP3/MP4 dane-elec music my touch or only dane-elec with 8 gb in memory and perhapses model zt1 with radio,..and microsdhc card slot following the above link the mp3/mp4 is there and it is MP3 Player: TOUCH MY MUSIC and the complete information is on this site http://www.danedigital.com/8-Music-Media-Players/2-music-touch.html as the Technical Specifications MP3 Player: TOUCH MY MUSIC The Mp4 player has a very classy. It allows its users to play music and view photos and video. His fluent interface, its touch-pad, his radio and RDS Micro SDHC reader makes him a very complete device will become the ideal musical companion. ubuntu i am with is ubuntu 11.10 kernel 3.0.0-14-generic the latest I tried to install many applications but nothing worked. With disk utility I can see that Ubuntu can recognize something, that as a peripheral device named rockchip usbdisk user and rockchip usbdisk sd, and i can plug and play other devices, and only this mp3/mp4 do not connect to the computer with ubuntu and the device as no problem working disconnected to computer I try to see if work on Windows and it does! I can see the device and transfer files to the MP3/MP4 dane-elec folder device and use FAT32. So why can not do on Ubuntu!? What can I do and why does not work on Ubuntu? What is wrong with it? Here are the logs: Jan 4 17:27:34 a-ubuntu kernel: [ 141.948863] init: apport pre-start process (1970) terminated with status 1 Jan 4 17:27:34 a-ubuntu kernel: [ 141.963202] init: apport post-stop process (1994) terminated with status 1 Jan 4 17:30:02 a-ubuntu kernel: [ 289.564049] usb 2-4: new high speed USB device number 3 using ehci_hcd Jan 4 17:30:02 a-ubuntu kernel: [ 289.988706] usbcore: registered new interface driver uas Jan 4 17:30:02 a-ubuntu kernel: [ 289.992056] Initializing USB Mass Storage driver... Jan 4 17:30:02 a-ubuntu kernel: [ 289.992272] scsi6 : usb-storage 2-4:1.0 Jan 4 17:30:02 a-ubuntu kernel: [ 289.993082] usbcore: registered new interface driver usb-storage Jan 4 17:30:02 a-ubuntu kernel: [ 289.993088] USB Mass Storage support registered. Jan 4 17:30:03 a-ubuntu kernel: [ 290.996887] scsi 6:0:0:0: Direct-Access RockChip USBDISK User 1.00 PQ: 0 ANSI: 0 Jan 4 17:30:03 a-ubuntu kernel: [ 290.997372] scsi 6:0:0:1: Direct-Access RockChip USBDISK SD 1.00 PQ: 0 ANSI: 0 Jan 4 17:30:03 a-ubuntu kernel: [ 290.997478] scsi: killing requests for dead queue Jan 4 17:30:03 a-ubuntu kernel: [ 291.002712] scsi: killing requests for dead queue Jan 4 17:30:03 a-ubuntu kernel: [ 291.002880] scsi: killing requests for dead queue Jan 4 17:30:04 a-ubuntu kernel: [ 291.016249] scsi: killing requests for dead queue Jan 4 17:30:04 a-ubuntu kernel: [ 291.032252] scsi: killing requests for dead queue Jan 4 17:30:04 a-ubuntu kernel: [ 291.048182] scsi: killing requests for dead queue Jan 4 17:30:04 a-ubuntu kernel: [ 291.060178] scsi: killing requests for dead queue Jan 4 17:30:04 a-ubuntu kernel: [ 291.060357] scsi: killing requests for dead queue Jan 4 17:30:04 a-ubuntu kernel: [ 291.080381] sd 6:0:0:0: Attached scsi generic sg2 type 0 Jan 4 17:30:04 a-ubuntu kernel: [ 291.080646] sd 6:0:0:1: Attached scsi generic sg3 type 0 Jan 4 17:30:04 a-ubuntu kernel: [ 291.088381] sd 6:0:0:0: [sdb] 16015360 512-byte logical blocks: (8.19 GB/7.63 GiB) Jan 4 17:30:04 a-ubuntu kernel: [ 291.088988] sd 6:0:0:1: [sdc] Attached SCSI removable disk Jan 4 17:30:04 a-ubuntu kernel: [ 291.200050] usb 2-4: reset high speed USB device number 3 using ehci_hcd Jan 4 17:30:04 a-ubuntu kernel: [ 291.448044] usb 2-4: reset high speed USB device number 3 using ehci_hcd Jan 4 17:30:04 a-ubuntu kernel: [ 291.696055] usb 2-4: reset high speed USB device number 3 using ehci_hcd Jan 4 17:30:04 a-ubuntu kernel: [ 291.832046] sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled Jan 4 17:30:04 a-ubuntu kernel: [ 291.832994] sd 6:0:0:0: [sdb] Asking for cache data failed Jan 4 17:30:04 a-ubuntu kernel: [ 291.833001] sd 6:0:0:0: [sdb] Assuming drive cache: write through Jan 4 17:30:04 a-ubuntu kernel: [ 291.834378] sdb: detected capacity change from 8199864320 to 0 Jan 4 17:30:04 a-ubuntu kernel: [ 291.835367] sd 6:0:0:0: [sdb] Attached SCSI removable disk Jan 4 17:30:06 a-ubuntu kernel: [ 293.004741] sd 6:0:0:0: [sdb] 16015360 512-byte logical blocks: (8.19 GB/7.63 GiB) Jan 4 17:30:06 a-ubuntu kernel: [ 293.116051] usb 2-4: reset high speed USB device number 3 using ehci_hcd Jan 4 17:30:21 a-ubuntu kernel: [ 308.228043] usb 2-4: device descriptor read/64, error -110 Jan 4 17:30:36 a-ubuntu kernel: [ 323.444072] usb 2-4: device descriptor read/64, error -110 Jan 4 17:30:36 a-ubuntu kernel: [ 323.660047] usb 2-4: reset high speed USB device number 3 using ehci_hcd Jan 4 17:30:51 a-ubuntu kernel: [ 338.772085] usb 2-4: device descriptor read/64, error -110 Jan 4 17:31:06 a-ubuntu kernel: [ 353.988064] usb 2-4: device descriptor read/64, error -110 Jan 4 17:31:07 a-ubuntu kernel: [ 354.204058] usb 2-4: reset high speed USB device number 3 using ehci_hcd Jan 4 17:31:12 a-ubuntu kernel: [ 359.224115] usb 2-4: device descriptor read/8, error -110 Jan 4 17:31:17 a-ubuntu kernel: [ 364.344136] usb 2-4: device descriptor read/8, error -110 Jan 4 17:31:17 a-ubuntu kernel: [ 364.560037] usb 2-4: reset high speed USB device number 3 using ehci_hcd Jan 4 17:31:22 a-ubuntu kernel: [ 369.580132] usb 2-4: device descriptor read/8, error -110 Jan 4 17:31:27 a-ubuntu kernel: [ 374.700126] usb 2-4: device descriptor read/8, error -110 Jan 4 17:31:27 a-ubuntu kernel: [ 374.804121] usb 2-4: USB disconnect, device number 3 Jan 4 17:31:27 a-ubuntu kernel: [ 374.804518] sd 6:0:0:0: Device offlined - not ready after error recovery Jan 4 17:31:27 a-ubuntu kernel: [ 374.804600] sd 6:0:0:0: [sdb] No Caching mode page present Jan 4 17:31:27 a-ubuntu kernel: [ 374.804606] sd 6:0:0:0: [sdb] Assuming drive cache: write through Jan 4 17:31:27 a-ubuntu kernel: [ 374.804693] sd 6:0:0:0: [sdb] READ CAPACITY failed Jan 4 17:31:27 a-ubuntu kernel: [ 374.804698] sd 6:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK Jan 4 17:31:27 a-ubuntu kernel: [ 374.804704] sd 6:0:0:0: [sdb] Sense not available. Jan 4 17:31:27 a-ubuntu kernel: [ 374.804744] sd 6:0:0:0: [sdb] No Caching mode page present Jan 4 17:31:27 a-ubuntu kernel: [ 374.804748] sd 6:0:0:0: [sdb] Assuming drive cache: write through Jan 4 17:31:27 a-ubuntu kernel: [ 374.804754] sdb: detected capacity change from 8199864320 to 0 Jan 4 17:31:27 a-ubuntu kernel: [ 374.820273] scsi: killing requests for dead queue Jan 4 17:31:27 a-ubuntu kernel: [ 374.852240] scsi: killing requests for dead queue Jan 4 17:31:27 a-ubuntu kernel: [ 374.980054] usb 2-4: new high speed USB device number 4 using ehci_hcd Jan 4 17:31:43 a-ubuntu kernel: [ 390.092059] usb 2-4: device descriptor read/64, error -110 Jan 4 17:31:58 a-ubuntu kernel: [ 405.308070] usb 2-4: device descriptor read/64, error -110 Jan 4 17:31:58 a-ubuntu kernel: [ 405.524078] usb 2-4: new high speed USB device number 5 using ehci_hcd and the other post is: http://pastebin.ubuntu.com/792915/ and the other bDeviceSubClass 2 ? bDeviceProtocol 1 Interface Association bMaxPacketSize0 64 idVendor 0x04f2 Chicony Electronics Co., Ltd idProduct 0xb008 USB 2.0 Camera bcdDevice 93.27 iManufacturer 2 Chicony Electronics Co., Ltd. iProduct 1 Chicony USB 2.0 Camera iSerial 3 SN0001 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 565 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 0 bInterfaceCount 2 bFunctionClass 14 Video bFunctionSubClass 3 Video Interface Collection bFunctionProtocol 0 iFunction 1 Chicony USB 2.0 Camera Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 14 Video bInterfaceSubClass 1 Video Control bInterfaceProtocol 0 iInterface 1 Chicony USB 2.0 Camera VideoControl Interface Descriptor: bLength 13 bDescriptorType 36 bDescriptorSubtype 1 (HEADER) bcdUVC 1.00 wTotalLength 77 dwClockFrequency 15.000000MHz bInCollection 1 baInterfaceNr( 0) 1 VideoControl Interface Descriptor: bLength 9 bDescriptorType 36 bDescriptorSubtype 3 (OUTPUT_TERMINAL) bTerminalID 2 wTerminalType 0x0101 USB Streaming bAssocTerminal 0 bSourceID 4 iTerminal 0 VideoControl Interface Descriptor: bLength 26 bDescriptorType 36 bDescriptorSubtype 6 (EXTENSION_UNIT) bUnitID 4 guidExtensionCode {7033f028-1163-2e4a-ba2c-6890eb334016} bNumControl 1 bNrPins 1 baSourceID( 0) 3 bControlSize 1 bmControls( 0) 0x01 iExtension 0 VideoControl Interface Descriptor: bLength 18 bDescriptorType 36 bDescriptorSubtype 2 (INPUT_TERMINAL) bTerminalID 1 wTerminalType 0x0201 Camera Sensor bAssocTerminal 0 iTerminal 0 wObjectiveFocalLengthMin 0 wObjectiveFocalLengthMax 0 wOcularFocalLength 0 bControlSize 3 bmControls 0x00000000 VideoControl Interface Descriptor: bLength 11 bDescriptorType 36 bDescriptorSubtype 5 (PROCESSING_UNIT) Warning: Descriptor too short bUnitID 3 bSourceID 1 wMaxMultiplier 0 bControlSize 2 bmControls 0x0000053f Brightness Contrast Hue Saturation Sharpness Gamma Backlight Compensation Power Line Frequency iProcessing 0 bmVideoStandards 0x a NTSC - 525/60 SECAM - 625/50 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0010 1x 16 bytes bInterval 6 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 14 Video bInterfaceSubClass 2 Video Streaming bInterfaceProtocol 0 iInterface 0 VideoStreaming Interface Descriptor: bLength 14 bDescriptorType 36 bDescriptorSubtype 1 (INPUT_HEADER) bNumFormats 1 wTotalLength 345 bEndPointAddress 129 bmInfo 0 bTerminalLink 2 bStillCaptureMethod 0 bTriggerSupport 1 bTriggerUsage 0 bControlSize 1 bmaControls( 0) 27 VideoStreaming Interface Descriptor: bLength 27 bDescriptorType 36 bDescriptorSubtype 4 (FORMAT_UNCOMPRESSED) bFormatIndex 1 bNumFrameDescriptors 7 guidFormat {59555932-0000-1000-8000-00aa00389b71} bBitsPerPixel 16 bDefaultFrameIndex 1 bAspectRatioX 0 bAspectRatioY 0 bmInterlaceFlags 0x00 Interlaced stream or variable: No Fields per frame: 2 fields Field 1 first: No Field pattern: Field 1 only bCopyProtect 0 VideoStreaming Interface Descriptor: bLength 46 bDescriptorType 36 bDescriptorSubtype 5 (FRAME_UNCOMPRESSED) bFrameIndex 1 bmCapabilities 0x00 Still image unsupported wWidth 640 wHeight 480 dwMinBitRate 614400 dwMaxBitRate 18432000 dwMaxVideoFrameBufferSize 614400 dwDefaultFrameInterval 333333 bFrameIntervalType 5 dwFrameInterval( 0) 333333 dwFrameInterval( 1) 500000 dwFrameInterval( 2) 666666 dwFrameInterval( 3) 1000000 dwFrameInterval( 4) 2000000 VideoStreaming Interface Descriptor: bLength 46 bDescriptorType 36 bDescriptorSubtype 5 (FRAME_UNCOMPRESSED) bFrameIndex 2 bmCapabilities 0x00 Still image unsupported wWidth 352 wHeight 288 dwMinBitRate 202752 dwMaxBitRate 6082560 dwMaxVideoFrameBufferSize 202752 dwDefaultFrameInterval 333333 bFrameIntervalType 5 dwFrameInterval( 0) 333333 dwFrameInterval( 1) 500000 dwFrameInterval( 2) 666666 dwFrameInterval( 3) 1000000 dwFrameInterval( 4) 2000000 VideoStreaming Interface Descriptor: bLength 46 bDescriptorType 36 bDescriptorSubtype 5 (FRAME_UNCOMPRESSED) bFrameIndex 3 bmCapabilities 0x00 Still image unsupported wWidth 320 wHeight 240 dwMinBitRate 153600 dwMaxBitRate 4608000 dwMaxVideoFrameBufferSize 153600 dwDefaultFrameInterval 333333 bFrameIntervalType 5 dwFrameInterval( 0) 333333 dwFrameInterval( 1) 500000 dwFrameInterval( 2) 666666 dwFrameInterval( 3) 1000000 dwFrameInterval( 4) 2000000 VideoStreaming Interface Descriptor: bLength 46 bDescriptorType 36 bDescriptorSubtype 5 (FRAME_UNCOMPRESSED) bFrameIndex 4 bmCapabilities 0x00 Still image unsupported wWidth 176 wHeight 144 dwMinBitRate 50688 dwMaxBitRate 1520640 dwMaxVideoFrameBufferSize 50688 dwDefaultFrameInterval 333333 bFrameIntervalType 5 dwFrameInterval( 0) 333333 dwFrameInterval( 1) 500000 dwFrameInterval( 2) 666666 dwFrameInterval( 3) 1000000 dwFrameInterval( 4) 2000000 VideoStreaming Interface Descriptor: bLength 46 bDescriptorType 36 bDescriptorSubtype 5 (FRAME_UNCOMPRESSED) bFrameIndex 5 bmCapabilities 0x00 Still image unsupported wWidth 160 wHeight 120 dwMinBitRate 38400 dwMaxBitRate 1152000 dwMaxVideoFrameBufferSize 38400 dwDefaultFrameInterval 333333 bFrameIntervalType 5 dwFrameInterval( 0) 333333 dwFrameInterval( 1) 500000 dwFrameInterval( 2) 666666 dwFrameInterval( 3) 1000000 dwFrameInterval( 4) 2000000 VideoStreaming Interface Descriptor: bLength 34 bDescriptorType 36 bDescriptorSubtype 5 (FRAME_UNCOMPRESSED) bFrameIndex 6 bmCapabilities 0x00 Still image unsupported wWidth 1280 wHeight 800 dwMinBitRate 2048000 dwMaxBitRate 18432000 dwMaxVideoFrameBufferSize 2048000 dwDefaultFrameInterval 1333333 bFrameIntervalType 2 dwFrameInterval( 0) 1333333 dwFrameInterval( 1) 2000000 VideoStreaming Interface Descriptor: bLength 34 bDescriptorType 36 bDescriptorSubtype 5 (FRAME_UNCOMPRESSED) bFrameIndex 7 bmCapabilities 0x00 Still image unsupported wWidth 1280 wHeight 1024 dwMinBitRate 2621440 dwMaxBitRate 23592960 dwMaxVideoFrameBufferSize 2621440 dwDefaultFrameInterval 1333333 bFrameIntervalType 2 dwFrameInterval( 0) 1333333 dwFrameInterval( 1) 2000000 VideoStreaming Interface Descriptor: bLength 6 bDescriptorType 36 bDescriptorSubtype 13 (COLORFORMAT) bColorPrimaries 1 (BT.709,sRGB) bTransferCharacteristics 1 (BT.709) bMatrixCoefficients 4 (SMPTE 170M (BT.601)) Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 1 bNumEndpoints 1 bInterfaceClass 14 Video bInterfaceSubClass 2 Video Streaming bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 5 Transfer Type Isochronous Synch Type Asynchronous Usage Type Data wMaxPacketSize 0x0080 1x 128 bytes bInterval 1 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 2 bNumEndpoints 1 bInterfaceClass 14 Video bInterfaceSubClass 2 Video Streaming bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 5 Transfer Type Isochronous Synch Type Asynchronous Usage Type Data wMaxPacketSize 0x0100 1x 256 bytes bInterval 1 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 3 bNumEndpoints 1 bInterfaceClass 14 Video bInterfaceSubClass 2 Video Streaming bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 5 Transfer Type Isochronous Synch Type Asynchronous Usage Type Data wMaxPacketSize 0x0320 1x 800 bytes bInterval 1 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 4 bNumEndpoints 1 bInterfaceClass 14 Video bInterfaceSubClass 2 Video Streaming bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 5 Transfer Type Isochronous Synch Type Asynchronous Usage Type Data wMaxPacketSize 0x0b20 2x 800 bytes bInterval 1 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 5 bNumEndpoints 1 bInterfaceClass 14 Video bInterfaceSubClass 2 Video Streaming bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 5 Transfer Type Isochronous Synch Type Asynchronous Usage Type Data wMaxPacketSize 0x1320 3x 800 bytes bInterval 1 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 6 bNumEndpoints 1 bInterfaceClass 14 Video bInterfaceSubClass 2 Video Streaming bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 5 Transfer Type Isochronous Synch Type Asynchronous Usage Type Data wMaxPacketSize 0x13e8 3x 1000 bytes bInterval 1 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 239 Miscellaneous Device bDeviceSubClass 2 ? bDeviceProtocol 1 Interface Association bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) Bus 006 Device 002: ID 04d9:1503 Holtek Semiconductor, Inc. Shortboard Lefty Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x04d9 Holtek Semiconductor, Inc. idProduct 0x1503 Shortboard Lefty bcdDevice 3.10 iManufacturer 1 iProduct 2 USB Keyboard iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 59 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 1 Keyboard iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.10 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 62 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 0 No Subclass bInterfaceProtocol 0 None iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.10 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 101 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Device Status: 0x0000 (Bus Powered)

  Read the article

• Unauthorized access error to html pages in IIS 7.0

  - by George2

  Hello everyone, I am using VSTS 2008 + C# + .Net 3.5 + IIS 7.0. I have created a new web site and put an html file into the directory. And when I use browse function in IIS manager to browse the html file, I met with the following error, any ideas what is wrong? BTW: I am very confused about unauthorized error since I run the worker process under administrator account. From the error message, I am confused why the logon method is anonymous and not using administrator account? HTTP Error 401.3 - Unauthorized You do not have permission to view this directory or page because of the access control list (ACL) configuration or encryption settings for this resource on the Web server. Module IIS Web Core Notification AuthenticateRequest Handler StaticFile Error Code 0x80070005 Requested URL http://localhost:80/a.html Physical Path C:\test\simplehosttest\a.html Logon Method Anonymous Logon User Anonymous thanks in advance, George

  Read the article

• Unity launcher doesn't appear in VNC session

  - by Lorin Hochstein

  I'd like to have a unity desktop accessible via VNC on a precise server machine I have running. I installed the ubuntu-desktop package. I'm launching a VNC session with the following in my ~/.vnc/xstartup file: !/bin/sh xrdb $HOME/.Xresources xsetroot -solid grey export XKL_XMODMAP_DISABLE=1 gnome-session --session=ubuntu-2d What could the issue be here? The content of my /usr/share/gnome-session/sessions/ubuntu-2d.session file (this is what 12.04 puts there by default) is: [GNOME Session] Name=Ubuntu 2D RequiredComponents=gnome-settings-daemon; RequiredProviders=windowmanager;panel;shell; DefaultProvider-windowmanager=metacity DefaultProvider-panel=unity-2d-panel DefaultProvider-shell=unity-2d-shell DesktopName=Unity I don't know anything about unity-2d, but I guessed that the default session was not configured to use the launcher. I tried making the following modifications: [GNOME Session] Name=Ubuntu 2D RequiredComponents=gnome-settings-daemon; RequiredProviders=windowmanager;panel;shell;launcher; DefaultProvider-windowmanager=metacity DefaultProvider-panel=unity-2d-panel DefaultProvider-shell=unity-2d-shell DefaultProvider-launcher=unity-2d-launcher DesktopName=Unity But I got the following warning in my VNC log file: gnome-session[10354]: WARNING: Unable to find default provider 'qr' of required provider 'launcher' And the VNC session wouldn't even start with that configuration.

  Read the article

• Linux: setting up an elite/high-anonimity Web proxy on a dedicated server

  - by YellowSquirrel

  I'm renting a dedicated server which I'd like to use to "surf the Web": basically I want to always surf the Web from the same static IP (the one of my dedicated server). I can do it by running Xvnc/FreeNX on the dedicated server, but this is kinda slow and clumsy (I tried it). What are the steps needed to install an "elite/high-anonimity" Web proxy on a dedicated (Debian) Linux server knowing that my two requirements are: I'm the only person that needs access to the proxy all I want is that my broadband (dynamic) IP is completely hidden (I want to always surf from my dedicated server's IP). Note that using the static IP people can find my domains and my real name and I'm perfectly fine with that (actually it is what I want). What I don't want is people knowing from which dynamic IP (broadband) I'm connecting. What are the steps needed to do that? (basically I don't care about "anonimity", what I want is to appear to surf from a static IP and I think I need what is called an "elite" Web proxy to do that, but I'm not sure) Technical infos and sample configuration most welcome :)

  Read the article

• How do I install 32-bit perl-tgicl 2.1.1?

  - by Daniel Fernandez

  I'm trying to install a .deb and I need some packages but they are not on the synaptic. How can I install this packages lib32z1 libc6-i386 TGICL$ sudo dpkg -i perl-tgicl_2.1-1_all.deb Selecting previously deselected package perl-tgicl. (Reading database ... 168515 files and directories currently installed.) Unpacking perl-tgicl (from perl-tgicl_2.1-1_all.deb) ... dpkg: dependency problems prevent configuration of perl-tgicl: perl-tgicl depends on lib32z1 (>= 1:1.1.4); however: Package lib32z1 is not installed. perl-tgicl depends on libc6-i386 (>= 2.3); however: Package libc6-i386 is not installed. perl-tgicl depends on libfile-homedir-perl (>= 0.10); however: Package libfile-homedir-perl is not installed. perl-tgicl depends on libfile-spec-perl (>= 0.10); however: Package libfile-spec-perl is not installed. dpkg: error processing perl-tgicl (--install): dependency problems - leaving unconfigured Processing triggers for man-db ... Errors were encountered while processing: perl-tgicl My OS: $ uname -a Linux 3.0.0-12-generic-pae #20-Ubuntu SMP Fri Oct 7 16:37:17 UTC 2011 i686 i686 i386 GNU/Linux

  Read the article

• VPN with wrong subnet mask

  - by Philipp Schmid

  I followed these instructions on www.hottonetworking.com to set up VPN on a clean install of Windows Server 2008 SP2 (not R2 yet). When I then establish a VPN connection to that machine from a client machine (running Windows 7 RC), everything succeeds (it seems since I get a 'Connected' state in the network sharing center window), but I end up with a subnet mask (according to ipconfig /all) of 255.255.255.255 instead of 255.255.255.0. The net effect is that I don't have local network or internet capability. What additional configuration steps do I have to do to get VPN with the proper subnet mask working? Update: Using the steps outlined in the Technet article mentioned by Mr. Nimble, I was able to get internet connection. Apparently the subnet mask is not an issue as my coworker was able to connect using his VPN connection and ping the server machine by name as well.

  Read the article

• uwsgi_params not in nginx

  - by Halit Alptekin

  Firstly I setup nginx and uwsgi via apt-get. And,I add the line to nginx conf file(/etc/nginx/conf.d/default.conf) like below line; server { listen 80; server_name <replace with your hostname>; #Replace paths for real deployments... access_log /tmp/access.log; error_log /tmp/error.log; location / { include uwsgi_params; uwsgi_pass 127.0.0.1:8889; } } I had a error; Starting nginx: [emerg]: open() "/etc/nginx/uwsgi_params" failed (2: No such file or directory) in /etc/nginx/conf.d/default.conf:11 configuration file /etc/nginx/nginx.conf test failed If I add uwsgi_params file from uwsgi's source;I had a simple error. Thanks

  Read the article

• Oracle Service Bus JMS Deployments Utility by Mike Muller

  - by JuergenKress

  For proxy services utilizing the JMS transport, OSB receives messages from destinations by using an MDB. These MDBs get generated and deployed during activation of the service configuration. OSB creates a random, unique name for the J2EE application that gets deployed to WLS. The name starts with “_ALSB_” and ends in a unique series of digits. The EAR files are written to the sbgen subdirectory of the domain home directory. You will see these applications on the WLS console page for “Deployments”. For various operational reasons, there are times when the application name for a given proxy service needs to be determined. Since the generated name of the application doesn’t reflect the name of the service, it becomes difficult to determine the relationship between the service and its EAR file. In fact, it can not be discerned from either the OSB or WLS consoles.Read the full article here. SOA & BPM Partner Community For regular information on Oracle SOA Suite become a member in the SOA & BPM Partner Community for registration please visit www.oracle.com/goto/emea/soa (OPN account required) If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Facebook Wiki Mix Forum Technorati Tags: Service bus,OSB,JMS,SOA Community,Oracle SOA,Oracle BPM,Community,OPN,Jürgen Kress

  Read the article

• Unusual Restart

  - by Nikit Batale

  I am currently running Windows XP Professional on my computer. My configuration is Intel Dual Core 3.00 GHz, 512 MB RAM, 160 GB HDD. Sometimes, the computer just restarts without any particular reason. After restarting, I get an error report, "Windows has just recovered from a serious error." Such incidents happen once in 5-6 days. I don't face any other problems apart from this. Also, I don't face this problem in Ubuntu Karmic Koala though.

  Read the article

• Why is IaaS important in Azure&hellip;

  - by Steve Loethen

  Three weeks ago, Microsoft released the next phase of Azure.  I have had several clients waiting on this release.  The fact that they have been waiting and are now more receptive to looking at the cloud.  Customers expressed fear of the unknown.  And a fear of lack of control, even when that lack of control also means a huge degree of flexibility to innovate with concerns about the underlying infrastructure.  I think IaaS will be that “gateway drug” to get customers who have been hesitant to take another look at the cloud.  The dialog can change from the cloud being this big scary unknown to a resource for workloads.  The conversations should have always been, and can know be even stronger, geared toward the following points: 1) The cloud is not unicorns and glitter, the cloud is resources.  Compute, storage, db’s, services bus, cache…..  Like many of the resources we have on-premise.  Not magic, just another resource with advantages and obstacles like any other resource. 2) The cloud should be part of the conversation for any new project.  All of the same criteria should be applied, on-premise or off.  Cost, security, reliability, scalability, speed to deploy, cost of licenses, need to customize image, complex workloads.  We have been having these discussions for years when we talk about on-premise projects.  We make decisions on OS’s, Databases, ESB’s, configuration and products based on a myriad of factors.  We use the same factors but now we have a additional set of resources to consider in our process. 3) The cloud is a great solution looking for some interesting problems.  It is our job to recognize the right problems that fit into the cloud, weigh the factors and decide what to do. IaaS makes this discussion easier, offers more choices, and often choices that many enterprises will find more better than PaaS.  Looking forward to helping clients realize the power of the cloud.

  Read the article

• Setting up Github post-receive webhook with private Jenkins and private repo

  - by Joseph S.

  I'm trying to set up a private GitHub project to send a post-receive request to a private Jenkins instance to trigger a project build on branch push. Using latest Jenkins with the GitHub plugin. I believe I set up everything correctly on the Jenkins side because when sending a request from a public server with curl like this: curl http://username:password@ipaddress:port/github-webhook/ results in: Stacktrace: net.sf.json.JSONException: null object which is fine because the JSON payload is missing. Sending the wrong username and password in the URI results in: Exception: Failed to login as username I interpret this as a correct Jenkins configuration. Both of these requests also result in entries in the Jenkins log. However, when pasting the exact same URI from above into the Github repository Post-Receive URLs Service Hook and clicking on Test Hook, absolutely nothing seems to happen on my server. Nothing in the Jenkins log and the GitHub Hook Log in the Jenkins project says Polling has not run yet. I have run out of ideas and don't know how to proceed further.

  Read the article

• GConf error and gnome does not load properly in RHEL 5.3

  - by Tim

  Hello, I am using Red Hat Enterprise Linux 5.3 . I created a user oracle on the system, using the following command useradd -g oinstall -G dba,oper -d /home/oracle oracle Now, when i try to login as the user oracle, GNOME does not load properly and i get popup box error message like the following GConf error:Failed to contact configuration server;some possible causes are that you need to enable TCP/IP for ORBit,or your have NFS locks due to a system crash.(Details-/:IOR file'/tmp/gcofd-cheetahman/tock/ior' not opened successfully,no gconfd located:Permission denied 2: IOR file /tmp/gconfd-cheetahman/lock/ior not opened succesfully no gconfd located: Permission denied) Any way to fix this ? Thank You

  Read the article

< Previous Page | 428 429 430 431 432 433 434 435 436 437 438 439  | Next Page >