Search Results

Search found 18029 results on 722 pages for 'stripe size'.

Page 434/722 | < Previous Page | 430 431 432 433 434 435 436 437 438 439 440 441  | Next Page >

• UDP multicast streaming of media content over WIFI

  - by sajad

  I am using vlc to stream media content over wireless network in scenario like this (from content streamer to stream receiver client): The bandwidth of wireless network is 54 Mb/s and UDP stream's required bandwidth is only 4 Mb/s; however there is trouble in receiving media stream and quality of playing specifically in multicast mode; means I can play the stream but it has jitter and does not play smoothly. In uni-cast I can stream up to 5 media streams correctly, but in multicast mode there is problem with streaming just one media! However when I stream from client some multicast streams; the wifi access-point can receive data correctly and I can see the video in "udp streamer" side correctly even when number of multicast streams increases to 9; But as you see I want to stream from streaming server and receive media in client size. Is this a typical problem of streaming real-time contents over wireless networks? Is it necessary to change configurations of my WIFI switch or it is just a software trouble? thank you

  Read the article

• Vantec NexStar NAS Encloser - Writing large files

  - by peter

  Hi, I have one of these 'Vantec NexStar LX - NST-475LX-BK' drive enclosures. It is a NAS drive. When I write a file to the device using eSata, or a SMB share I cannot write files over 2GB. I think this is because the drive is formatted with FAT32. But when I access the device using FTP it doesn't matter. I can write files of any size. E.g. I wrote one on there last night which was 30GB. Does this make any sense? Why? I guess the most important thing for me is data integrity.

  Read the article

• Distributed, Parallel, Fault-tolerant File System

  - by Eddified

  There are so many choices that it's hard to know where to start. My requirements are these: Runs on Linux Most of the files will be between 5-9 MB in size. There will also be a significant number of small-ish jpgs (100px x 100px). All of the files need to be available over http. Redundancy -- ideally it would provide the space efficiency similar to RAID 5 of 75% (in RAID 5 this would be calculated thus: with 4 identical disks, 25% of the space is used for parity = 75% efficent) Must support several petabytes of data scalable runs on commodity hardware In addition, I look for these qualities, though they are not "requirements": Stable, mature file system Lots of momentum and support etc I would like some input as to which file system works best for the given requirements. Some people at my organization are leaning towards MogileFS, but I'm not convinced of the stability and momentum of that project. GlusterFS and Lustre, based on my limited research, appear to be better supported... Thoughts?

  Read the article

• 2012 Oracle Fusion Middleware Innovation Awards Announced

  - by Tanu Sood

  Guest Contributor: Margaret Harrist. Originally posted on Oracle NewsCentral Companies from around the world were honored Tuesday for their innovative solutions using Oracle Fusion Middleware. This year’s 27 award winners, representing 11 countries and a wide span of industries, wowed the judges with a range of projects across eight product categories. A panel of judges scored each entry across multiple categories, including the uniqueness of their business case, business benefits, level of impact relative to the size of the organization, complexity and magnitude of implementation, and the architecture’s originality. In a general session just before the award presentation, Oracle Executive Vice President Hasan Rizvi highlighted a few of the winners’ original implementations, including Nike, Los Angeles Department of Water and Power, and Nintendo of America. Congratulations to the 2012 winners: Oracle Exalogic: Netshoes, Claro, UL, and Ingersoll Rand Oracle Cloud Application Foundation: Mazda Motor Corporation, HOTELBEDS Technology, Globalia, Nike, and Comcast Corporation Oracle SOA and Oracle BPM: NTT Docomo, Schneider National, Amadeus, and Motability Oracle WebCenter: News Limited, University of Louisville, China Mobile Jiangsu, Life Technologies Oracle Identity Management: Education Testing Service and Avea Oracle Data Integration: Raymond James and William Morrison Supermarkets Oracle Application Development Framework and Oracle Fusion Development: Qualcomm, Micros Systems, and Marfin Egnatia Bank Business Analytics (Oracle BI, Oracle EPM, Oracle Exalytics): INC Research, Experian, and Hologic

  Read the article

• Outlook pst problem

  - by tking

  I've used outlook pst files in the past with great success. a few weeks ago I exported about 2 years worth of email into a pst file. size is around 1.5 gb. when i try ti import that pst back into my outlook it says its not a pst file. I've tried to repair it using pstscan and it repairs errors and will even mount it in Outlook but Outlook cant see any emails, like its an empty pst file. Is there any other way to recover my emails besides loading up backupexec and recovering my mailbox before i made the pst?

  Read the article

• Rendering text with stb_font results in glitches

  - by Fabian Fritz

  I'm trying to render text with OpenGL and an "inline"-font taken from the stb_fonts The relevant code for initializing the font & rendering: LabelFactory::LabelFactory() { static unsigned char fontpixels [STB_SOMEFONT_BITMAP_HEIGHT][STB_SOMEFONT_BITMAP_WIDTH]; STB_SOMEFONT_CREATE(fontdata, fontpixels, STB_SOMEFONT_BITMAP_HEIGHT); glGenTextures(1, &texture); glBindTexture(GL_TEXTURE_2D, texture); glTexEnvf(GL_TEXTURE_ENV, GL_TEXTURE_ENV_MODE, GL_MODULATE); glTexImage2D(GL_TEXTURE_2D, 0, GL_ALPHA, STB_SOMEFONT_BITMAP_WIDTH, STB_SOMEFONT_BITMAP_HEIGHT, 0, GL_ALPHA, GL_UNSIGNED_BYTE, fontdata); glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MIN_FILTER, GL_LINEAR); } void LabelFactory::renderLabel(Label * label) { int x = label->x; int y = label->y; const char * str = label->text; glBindTexture(GL_TEXTURE_2D, texture); glEnable(GL_BLEND); glBlendFunc(GL_SRC_ALPHA, GL_ONE_MINUS_SRC_ALPHA); glEnable(GL_ALPHA_TEST); glColor4f(1.0f, 1.0f, 1.0f, 1.0f); glEnable(GL_TEXTURE_2D); glBegin(GL_QUADS); while (*str) { int char_codepoint = *str++; stb_fontchar *cd = &fontdata[char_codepoint - STB_FONT_arial_14_usascii_FIRST_CHAR]; glTexCoord2f(cd->s0, cd->t0); glVertex2i(x + cd->x0, y + cd->y0); glTexCoord2f(cd->s1, cd->t0); glVertex2i(x + cd->x1, y + cd->y0); glTexCoord2f(cd->s1, cd->t1); glVertex2i(x + cd->x1, y + cd->y1); glTexCoord2f(cd->s0, cd->t1); glVertex2i(x + cd->x0, y + cd->y1); x += cd->advance_int; } glEnd(); } However this results in weird glitches I guess I'm doing something wrong with the alpha blending, however I was unable to improve it by changing the parameters. The size and length of the outline of the text that should be shown seems about right (it should read "Test Test Test").

  Read the article

• Deleting MySQL rows causes lock table error

  - by Dave L

  I had a couple million rows to delete but they can't be deleted at once without this error ERROR 1206 (HY000): The total number of locks exceeds the lock table size So I wrote a script to delete 100,000 rows 10,000 at a time. It ran once but when I run it a second time I get the error on the first attempt to delete 10,000. The way I'm trying to delete the 10,000 rows is to use a delete statement that refers to all 2 million rows but I use a limit clause to affect only 10,000. I've tried adding an "unlock tables;" statement to the script before the first delete but that doesn't help. I still get the lock table error on the first delete. Any ideas how I can do this? Is there a way I can tell it NOT to lock records? I can make sure nothing else is accessing the table.

  Read the article

• Multi-Resolution Mobile Development

  - by user2186302

  I'm about to start development on my first game for mobile phone (I already have a flash prototype completed so it's jsut a matter of "porting" it to mobile and fixing up the code) and plan on hopefully being able to get the game working on iphones and most android devices. I am using Haxe along with OpenFL and HaxeFlixel for development. My question is: What resolution should I design the game in initially and/or what is the best way to develop a game for multiple resolutions. I have found multiple different methods, the best, in my opinion, being strategy 3 on this page: http://wiki.starling-framework.org/manual/multi-resolution_development. However I have some questions about this. First, what would the best base resolution to use be, the guide suggests 240*320 which seems alright to me, although if I chose to use pixel graphics as I most probably will given I'm using HaxeFlixel, I'm not sure if they'll look too blocky on larger screens which I'm not even sure is a problem as it might still look alright. (Honestly, not sure about that and if anyone has any examples of games that use this method and look nice). Finally, please feel free to share whatever methods you use and think is best. For example, HaxeFlixel has a scaling feature that scales the game to fit the exact screen size, but I'm afraid that would lead to blurry and improperly scaled graphics since it would scale by non-integers. But, I'm not sure how noticeable a problem that may or may not be. Although from experience I'm pretty sure it won't look nice and currently I do not think I'm going to go for this option. So, I would really appreciate any help on this subject. Thank you in advance.

  Read the article

• Boot ubuntu 12.04 in 3D - nomodeset quiet splash install

  - by rahi

  I would like to enable 3D in Ubuntu 12.04. I recently tried to install ubuntu on a new computer. When the installation was complete and I rebooted the machine, I could only see a blank screen. After some searching, I followed this tutorial which instructed me to boot with "nomodeset" enabled. I choose this on the USB I was installing ubuntu 12.04 from. Fortunately, the ubuntu installation on the new computer was successful. When I tried to change the size of the unity launcher icons, I did not see that option (as I see on my other computer running ubuntu 12.04). I tried installing MyUnity and it told me that the computer I had just installed 12.04 to was running in 2D. To my knowledge. all the software is up to date (as I ran the Software Updater). In addition, when I look for Additional Drivers, I see a message that says "No proprietary drivers are in use on this system". When I look under System Details Graphics, I see the Driver as "VESA:Intel Sandybridge/Ivybridge Graphics. When I hold the shift key on when my machine boots up, and type "e" on the Grub menu, I see the following towards the end, "nomodeset quiet splash $vt_handoff". Does this have anything to do with the plain 2D ubuntu 12.04 experience? Again, what I'd like to do now is get the 3D experience on my new machine running 12.04. Please let me know if you need more information.

  Read the article

• Redhat | error in mod_swgi installation

  - by MMRUSer

  I'm getting the following error when I try to install mod_wsgi ./configure checking for apxs2... no checking for apxs... /usr/sbin/apxs checking Apache version... 2.2.3 configure: creating ./config.status config.status: creating Makefile make /usr/sbin/apxs -c -I/usr/local/include/python2.6 -DNDEBUG mod_wsgi.c -L/usr/local/lib -L/usr/local/lib/python2.6/config -lpython2.6 -lpthread -ldl -lutil -lm /apr-1/build/libtool --silent --mode=compile gcc -prefer-pic -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m32 -march=i386 -mtune=generic -fasynchronous-unwind-tables -fno-strict-aliasing -DLINUX=2 -D_REENTRANT -D_GNU_SOURCE -D_LARGEFILE64_SOURCE -pthread -I/usr/include/httpd -I/usr/include/apr-1 -I/usr/include/apr-1 -I/usr/local/include/python2.6 -DNDEBUG -c -o mod_wsgi.lo mod_wsgi.c && touch mod_wsgi.slo sh: /apr-1/build/libtool: No such file or directory apxs:Error: Command failed with rc=8323072 . make: *** [mod_wsgi.la] Error 1 mod_wsgi 3.2 Apache 2.2 Python 2.6 apr-1.2.7-11 Is this error because of a missing package.. or else how do I solve this issue?

  Read the article

• Disk Space Full

  - by Loki

  Setting up Ubuntu 10.04 server, the / disk space shows full under df, however the du does not show any of the space used. This has several mounts to Gluster FS'. I have tried a forced FSCK and to no avail. ~# df -h Filesystem Size Used Avail Use% Mounted on /dev/md0 141G 132G 0 100% / none 3.0G 224K 3.0G 1% /dev none 3.0G 0 3.0G 0% /dev/shm none 3.0G 76K 3.0G 1% /var/run none 3.0G 0 3.0G 0% /var/lock none 3.0G 0 3.0G 0% /lib/init/rw /dev/sdb1 9.0T 7.1T 1.9T 80% /brick1 /dev/sdb2 9.0T 7.9T 1.1T 88% /brick2 localhost:/sanvol09 385T 330T 56T 86% /mnt/sanvol09 <- Gluster FS uses local software to contact the DFS I've attempted a tune2fs and same issue arises # du -h --max-depth=1 --one-file-system / 4.0K /selinux 0 /proc 47M /boot 31M /mnt 8.0K /brick1 8.0K /brick2 391M /lib 4.0K /opt 7.4M /bin 0 /sys 379M /var 5.6M /etc 16K /lost+found 43M /root 4.0K /srv 5.7M /home 4.0K /media 7.0M /sbin 0 /dev 4.0K /tmp 4.0K /cdrom 631M /usr 1.6G / more info # df -ih Filesystem Inodes IUsed IFree IUse% Mounted on /dev/md0 9.0M 91K 8.9M 1% / none 746K 770 745K 1% /dev none 747K 1 747K 1% /dev/shm none 747K 32 747K 1% /var/run none 747K 1 747K 1% /var/lock none 747K 3 747K 1% /lib/init/rw /dev/sdb1 583M 1.8M 581M 1% /brick1 /dev/sdb2 583M 1.9M 581M 1% /brick2 localhost:/sanvol09 25G 76M 25G 1% /mnt/sanvol09 The final question: df show's 100% used, and its not, any other known fixes?

  Read the article

• What is the right way to Windows 7/Ubuntu 10.10 Dual-Triple Boot Partitioning for Laptop OEM?

  - by Denja

  Hi Linux Community, I find my self struggling with the ever slow and buggy windoze OS once again. It's Time to change with the Ubuntu 10.10 64bit as a really faster Operating System. My Hard Disk laptop as a RECOVERY and HP_TOOLS partition they are both Primary. I Have the System Recovery DVD for Windows 64bit should anything happen. Here's the layout I used with windows before: * (C:) Windows 7 system partition NTFS - 284,89GB (Primary,Boot,Pagefile,Dump) * HP_TOOLS system partition FAT32 - 99MB (Primary) * (D:) RECOVERY partition NTFS - 12,90GB (Primary) * SYSTEM partition NTFS 199MB (Primary) Here's the layout I want to make based on your answers * (C:) Windows 7 system partition NTFS - 60GB (Primary) (sda1) * (D:) Windows DATA partition (user files) NTFS - 120GB(Primary)(sda2);wanna share with Linux * Linux root Ext4 - 100GB (Primary)(sda3) (Ubuntu 10.10 64bit) * Linux swap swap- RAM size, 3GB (sda4) * Linux root Ext3- 15,9GB (Extended)(sda5) (OpenSuse or Puppy) Here is my New Ubuntu 10.10 64bit layout in use now: * SYSTEM partition NTFS 199MB (Primary) (sda1) **Partition 1 does not end on cylinder boundary.(?)** * (C:) Windows 7 system partition NTFS - 90GB (Primary) (sda2) * (D:) Windows 7 RECOVERY partition NTFS - 12,90GB (Primary) (sda3) * Linux system partition EXTENDED - 195GB (Logical) * Linux root Ext4- 10GB (Extended) (sda5) * Linux home Ext3- 185GB (Extended) (sda6) I didn't know if I could wipe all previous partitions when i installed Ubuntu because of the RECOVERY partition so I just made the space for my extended partition by deleting the HP_TOOLS (Fat32). By doing this I managed to make and successfully install Ubuntu 64 but I couldn't actually make the partition for the swap or a third Linux OS. Question 1: What is the right way to Windows 7/Ubuntu 10.10 Dual-Triple Boot Partitioning for Laptop OEM?? Thank you in advance for your advises and suggestions and Happy New Year to All!!

  Read the article

• Extract MP3 URL from a SWF file

  - by Charles

  I have a SWF file that basically shows a streamer, and it plays a song (I'm guessing it's MP3) that it links to, somewhere. I know the audio isn't embedded in the file since the SWF's file size is ~370KB. With most flash FLV and MP3 players, Internet Download Manager catches the URL as soon as the video/audio starts to load, and I can easily download it using IDM. In this case, IDM doesn't seem to sense anything - so I thought maybe I could extract the MP3 location myself. I tried decompiling the SWF file, as I'd heard before that with some files, decompiling can help in breaking down a file and getting just the info you need - but I honestly don't know what to look for in this particular file. Suggestions?

  Read the article

• Adding unallocated partition to Ubuntu in VMware

  - by AMS949

  I've installed Ubuntu 9.10 on a Windows XP using vmware. As most do, I initially setup the size of the virtual drive to 8GB and soon realized I need more. I used the VMware utility to expand the virtual drive and added another 4GB, which I can see using GParted. Now my dilemma is how can I "merge" the newly created space to my original? I need to add the unallocated space. I tried before and after formatting the new space but still whenever I try to resize/move /dev/sda1 it looks like it is using its maximum capacity. Also, GParted is being used from the GParted live CD not from the Linux live CD.

  Read the article

• Stacks in C++

  - by MarkPearl

  So some more basics… One of the things you will be taught at any college after conquering arrays is different derivatives of collections. Stack is one of the simplest of those and very useful… A stack is a LIFO (last in first out) data structure and has at least two basic method calls – push & pop. Push, “pushes” an item on the top of the stack. Pop, removes the top most item off the stack. Because all elements on a stack are of the same type, one can use an array to implement a stack or a linked list. With the array based approach, the first element in a stack would be the first element in the array, the second on the stack would be the second on the array, etc. One limitation with an array implementation of a stack is that unless the array is dynamic, one would have to have a preset max stack size (based on the bounds of the array). Linked lists is another approach that gets past this boundary by allowing you to dynamically grow or shrink a collection of data. Stacks have many applications… a typical computer science example would be Postfix Expression Calculator, where the LIFO principle is maintained.

  Read the article

• Making a game with responsive resolution

  - by alexandervrs

  I am making a game, however I wish for it to be resolution agnostic. My target resolution i.e. where things look as intended is 1600 x 900. My ideas are: Make the HUD stay fixed to the sides no matter what resolution, use different size for HUD graphics under a certain resolution and another under a certain large one. Use large HD sprites/backgrounds which are a power of 2, so they scale nicely. Use the player's native resolution. Scale the game area (not the HUD) to fit (resulting zooming in some and cropping the game area sides if necessary for widescreen, no stretch), but always fill the screen. Have a min and max resolution limit for small and very large displays where you will just change the resolution(?) or scale up/down to fit. What I am a bit confused though is what math formula I would use to scale the game area correctly based on the resolution no matter the aspect ratio, fully fit in a square screen and with some clip to the sides for widescreen. Pseudocode would help as well. :)

  Read the article

• Problems with Intel Video Resolution on Acer Laptop Wide Display

  - by ricstr

  I have an ACER Aspire 5332 laptop which I have just installed Ubuntu 12.04 x64, which is causing some issues with the video display on boot and video resolution. First and foremost, it will only boot past the purple screen if GRUB has been edited to replace 'quick splash' with 'nomodeset'. Secondly, once it has booted with the the 'nomodeset' option, it does not allow me to change the resolution higher or lower from 1024 x 786. Is it OK to use the 'nomodeset' for normal use? Will this compromise performance of other devices? The video card is an on-board one, integrated within the Intel GL40 chip-set. The display is a wide-screen LCD, and under Windows could operate under various resolutions. Ideally I would like it to operate on a resolution to fit the wide-screen display as it a bit stretched out at the moment, and less desktop space as I am used to. I believe the optimal resolution is 1366 x 768. Below is some information from the terminal which may be useful. ricstr@Aspire-5332:~$ lspci | grep -i VGA 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09) ricstr@Aspire-5332:~$ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 1024 x 768, current 1024 x 768, maximum 1024 x 768 default connected 1024x768+0+0 0mm x 0mm 1024x768 0.0*

  Read the article

• Converting 3 dimension byte array to a single byte array [on hold]

  - by Andrew Simpson

  I have a 3 dimensional byte array. The 3-d array represents a jpeg image. Each channel/array represents part of the RGB spectrum. I am not interested in retaining black pixels. A black pixel is represented by this atypical arrangement: myarray[0,0,0] =0; myarray[0,0,1] =0; myarray[0,0,2] =0; So, I have flattened this 3d array out to a 1d array by doing this byte[] AFlatArray = new byte[width x height x 3] and then assigning values respective to the coordinate. But like I said I do not want black pixels. So this array has to only contain color pixels with the x,y coordinate. The result I want is to re-represent the image from the i dimension byte array that only contains non-black pixels. How do I do that? It looks like I have to store black pixels as well because of the xy coordinate system. I have tried writing to a binary file but the size of that file is greater than the jpeg file as the jpeg file is compressed. I am using c#.

  Read the article

• Is a larger hard drive with the same cache, rpm, and bus type faster?

  - by Joel Coehoorn

  I recently heard that, all else being equal, larger hard are faster than smaller. It has to do with more bits passing under the read head as the drive spins - since a large drive packs the bits more tightly, the same amount of spin/time presents more data to the read head. I had not heard this before, and was inclined to believe the the read heads expected bits at a specific rate and would instead stagger data, so that the two drives would be the same speed. I now find myself looking at purchasing one of two computer models for the school where I work. One model has an 80GB drive, the other a 400GB (for ~$13 more). The size of the drive is immaterial, since users will keep their files on a file server where they can be backed up. But if the 400GB drive will really deliver a performance boost to the hard drive, the extra money is probably worth it. Thoughts?

  Read the article

• Why can't get more speed on iperf on windows xp

  - by SledgehammerPL

  I test my bandwith and throughput using iperf (jperf) on desktop PC with WinXP. I can't get more than 3Mbit/s outside until I change TCP Window size - about 84Kb is ok. but I can't force XP to use this value by default.. I try very many magic spells on Registry, use many TCP Optimisers - but nothing works. I will accept that that everything is ok, when I reboot the PC, run iperf and will see 18.1Mbit - like my Linux box standing very near my Windows XP Box. Is it possible?

  Read the article

• Maximum Length Of IP Address: 15 (IPv4) & 39(IPv6)

  - by Gopinath

  Problem You are designing a database table for a web application that requires to store IP address of users who visits the site. The IP address is required to be stored a character data in the table. To define size of the character column you need to know maximum length of IP address. So, what is the maximum length of an IP address? Solution The IPv4 version of IP address is in the following format 255.255.255.255 To store IPv4 address we require 15 characters. The IPv6 version of IP address is grouped into sets of 4 hex digits separated by colons, like the below 2001:0db8:85a3:0000:0000:8a2e:0370:7334 To store IPv6 address you require a 39 characters long column. Conclusion As IPv4 and IPv6 are the commonly use protocols, you better define a column with 39 characters length so that both the format address are saved in to the table without any issues. This article titled,Maximum Length Of IP Address: 15 (IPv4) & 39(IPv6), was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

  Read the article

• Special Value Sets in Oracle Applications

  - by Manoj Madhusoodanan

  Here I am going to explain Special Value Sets in Oracle Applications.I have a requirement in which I want to execute a BIP report with some parameters. The first parameter Current Month should allow only MON-YYYY format.Schedule Start Date and Schedule End Date should be with in first parameter month. Approach 1If the report is through PL/SQL Stored Procedure executable the we can do all the validation in backend. Approach 2Second approach is through Special Value Sets.This value set has events like Edit,Load and Validate.We can attach PL/SQL code snippet to each event.Here I am going to attach validation routine to Validate event to validate the user input.Validate event fires when the focus leaves from the item. Here I am going to create two special value sets ( one for first parameter and another for the second and third parameter). Value Set 1Name : XXCUST_CURRENT_MONTHList Type : List of ValuesFormat Type : CharMaximum Size : 8Validation Type : SpecialEvent : ValidateFunction : XXCUST_CURRENT_MONTH_VALIDATE_ROUTINEValue Set 2Name : XXCUST_DATESList Type : List of ValuesFormat Type : Standard DateValidation Type : SpecialEvent : ValidateFunction : XXCUST_DATES_VALIDATE_ROUTINE Note: Inside the validate routine I am using FND messages.Generate message file also using "FNDMDGEN apps/password 0 Y US XXCUST DB_TO_RUNTIME". Attach XXCUST_CURRENT_MONTH to first parameter.Also XXCUST_DATES to second and third parameter. Note: Since the program is using Special Value Sets it can be submit only through Oracle Forms.Submission through OA Framework and PL/SQL APIs are not recommended. OutputGive Current Date as 01-2012 Give Schedule Start Date out of current month.

  Read the article

• Can I change a MySQL table back and forth between InnoDB and MyISAM without any problems?

  - by Daniel Magliola

  I have a site with a decently big database, 3Gb in size, a couple of tables with a dozen million records. It's currently 100% on MyISAM, and I have the feeling that the server is going slower than it should because of too much locking, so I'd like to try going to InnoDB and see if that makes things better. However, I need to do that directly in production, because obviously without load this doesn't make any difference. However, I'm a bit worried about this, because InnoDB actually has potential to be slower, so the question is: If I convert all tables to InnoDB and it turns out i'm worse off than before, can I go back to MyISAM without losing anything? Can you think of any problems I might encounter? (For example, I know that InnoDB stores all data in ONE big file that only gets bigger, can this be a problem?) Thank you very much Daniel

  Read the article

• failed to use mutt to send mail to company mailbox

  - by Acewind

  I'm using mutt&postfix on CentOS 6.2: mutt-1.5.20-2.20091214hg736b6a.el6_1.1.x86_64 postfix-2.6.6-2.2.el6_1.x86_64 When I try to send mail to my company mailbox, I receive an error: mutt -s "test" [email protected] < /home/mail.txt error from postfix: : host out1.ourcompany.com[10.30.17.100] said: 555 Syntax error (in reply to MAIL FROM command) Then I try to use service sendmail as SMTP server, but also failed: **----- The following addresses had permanent fatal errors ----- (reason: 555 Syntax error) ----- Transcript of session follows ----- ... while talking to out1.ourcompany.com.: MAIL From: SIZE=667 <<< 555 Syntax error 554 5.0.0 Service unavailable** Any body can tell me why? Thanks!!!! I can make sure DNS is OK, and I set realname "root@myserver" in /etc/Muttrc

  Read the article

• Vertical alignment problem in textbox in Microsoft Word 2007

  - by Surjya Narayana Padhi

  I pardon as its not a programming question at all. But if anybody can answer this it will be usefull for me. In MS word 2007 I drew a textbox and entered some text. Then I right clicked on textbox and went to format shape Then went to TextBox tab and reduced the top internal margin to 0.1 cm. But still it seems there is too much space at the top inside the textbox. I am not able to position the text exactly at the vertical middle of textbox. If I choose the auto-rezide option in format Shape, the textBox size is increases automatically but the text remains exactly at vertical and horizontal middle of textbox. but anyhow I need the textbox to be small. This is very minor but annoying problem. Can anybody help?

  Read the article

< Previous Page | 430 431 432 433 434 435 436 437 438 439 440 441  | Next Page >