Search Results

Search found 15591 results on 624 pages for 'problems'.

Page 440/624 | < Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >

• BIOS unable to boot CD or Hard Drive

  - by Gabriel

  Motherboard Intel DQ35MP. HDD Caviar Green 1TB. I'm having problems with my BIOS and/or hard drive/disc drive. Came back from a trip, booted my computer, and realized that the BIOS wasn't booting anymore, just a black screen with no beep sounds. Only fans and lights on. Then I thought it might be caused by the video card, I removed it, and still no BIOS screen. Then I removed the hard drive and voila BIOS screen is back again. If the hard drive is defective then I can check that with a Rescue Disk. I inserted the CD on the Disc Tray but the computer did not respond to it, the screen freezes in black with an "E7" string at the bottom right corner just after the BIOS screen, this happens with or without discs. BIOS settings are set to default, and CD reading is on top of the boot device list. EDIT I removed the BIOS battery, rebooted the CPU, the BIOS screen showed up, and then it freezed in E7. Placed the BIOS batttery, rebooted and same thing, we are stuck with the E7 string. I uploaded a video to illustrate the problem http://www.youtube.com/watch?v=13jPdBcIrBU

  Read the article

• How can I wipe my iPod classic and fix any bad sectors on the hard drive without killing it?

  - by Sam Meldrum

  My iPod never finishes syncing and only syncs audio, not pictures or video - any ideas as to how I can fix it? My iPod classic 160GB worked well for a couple of years. I used to sync a lot of photos at full resolution to it, but this recently stopped working after I moved to Windows 7. iTunes is on latest version - 9.1.1.12 iPod software is up to date - 1.1.2 Windows 7 is fully up to date and patched The symptoms are that the iPod will start to sync, all audio (music and podcasts will sync successfully) but the syncing will then just appear to continue - itunes message: Syncing iPod. Do not Disconnect. This sync never completes - I have left it trying for days. I have tried resetting the iPod using the Restore button, whereupon it restarts sync from default options and again will sync audio, but nothing else. I suspect that something has gone wrong on the hard-drive - either a bad sector or some corrupt data. Is there a process I can go through to fix this? E.g. SpinRite or a format? If so how do I go about formatting an iPod and will it be recognised as an iPod after format and work as normal? Any advice on what to try next much appreciated? Update I have eliminated problems with the files, PC or iTunes as they sync fine to other iPods. I have also eliminated the cable by trying different cables which work with other iPods. What I'd really like to know is if there is any way to more fundamentally wipe the iPod safely, attempt to repair any bad sectors on the hard drive and then start from scratch. Anyone ever managed this?

  Read the article

• It takes a long time until Windows XP recognize I connected USB drive

  - by Pavol G

  I have a problem with my new USB disk. When I connect it to my laptop with Windows XP SP2 it takes about 4-5min until Windows recognizes it and shows it as a new disk. I can also see (disk's LED is blinking) that something is scanning the disk when I connect it; when this is done Windows immediately recognize it. Also when I'm copying data to this disk the speed is about 3.5MB/sec. It's connected using USB2.0. I tried to check for spyware (using Spybot), also tried running Windows in safe mode. But still have the same problems. Do you have any idea what could help to solve this problem? On Windows Vista (another laptop) everything is ok, disk loads in about 15sec and speed is about 20-30MB/sec. Edit: I tried to update to SP3 - no change Edit2: When this "strange" scanning occurs I can see that DPCs process is taking about 50% of CPU. When the scan ends (after 5min) this process take 0% again. Edit3: About the scan time, currently it's taking about 5min, but this time is growing as I'm adding more data to the disk, currently its about 40GB and I don't want to see how long it will take with 1000GB. Thanks a lot for every advice!

  Read the article

• IIS doesn't serve certain file extensions

  - by Alekc

  Hi, i have this weird issue on Win 2k3 server and IIS: Iis has several sites, in one of them i need to create a subdir and set up it as web application. I've noticed that if i create new directory and put some .js/.txt file into it, they will not be served by iis (IE gives an error Internet Explorer cannot display the webpage). If i put the same files in another old site's subdirectory it will show correctly. By sniffing traffic i've seen that iis reply connection state 200 and then drop completely any connection http://domain.com/test2/prova.txt GET /test2/prova.txt HTTP/1.1 Host: domain.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.1.7) Gecko/20091221 Firefox/3.5.7 (.NET CLR 3.5.30729) Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive HTTP/1.x 200 OK If i rename file prova.txt in prova.asp for example it showing without problems so it shouldn't be permissions issue. After making some researches I've found out that it can be caused by missing mime types, I've checked out .txt and .js are present and served by aspnet_isapi.dll. And here comes another weird thing: if i remove mime mapping from directory's properties it's served correctly, but the same thing doesn't work with js. I'm really beginning to be out of ideas, is there someone who have some hint? Thanks in advance.

  Read the article

• How to run a website domain without redirecting if IP is already used for another website? [duplicate]

  - by SSpoke

  This question already has an answer here: Hosting multiple distinct folders for distinct domains 1 answer I bought a VPS Host that gave me only 1 IP Address which I used on my first domain name and it works without any problems. Now my second domain name I can't use the same ip address as it points to the first domain name. So I figured my only option was to use a GoDaddy hosted iframe redirection which redirects to a sub folder on my first domain which worked so far. Now I'm trying to load paypal from <?php headers() ?> and I get a permission error because of that iframe Refused to display 'https://www.paypal.com/cgi-bin/webscr?notify_url=&cmd=_cart&upload=1&business=removed&address_override=1' in a frame because it set 'X-Frame-Options' to 'SAMEORIGIN'. How do I avoid the Iframe solution for my second domain while not messing up my first domain? Somebody I forgot once told me it doesn't matter if you have 1 IP Address you could host multiple websites on it? how it that possible the DNS doesn't seem to work off ports afaik, yes I could host multiple websites on different folders but that's not what I call hosting a real website it has to be pointed by a domain name, so this iframe issue doesn't happen My server configuration is httpd (apache) that comes with CentOS 6 (Linux) operating system

  Read the article

• Are there cloud network drives that let users lock files or mark them as "in use"?

  - by Brandon Craig Rhodes

  Having spent several hours reading about the features and limitations of services like DropBox and Jungle Disk and the hundreds of competitors they seem to have (as though everyone with an AWS account these days goes ahead and writes a file sharing application just for fun), I have yet to find one that would let a team of people at a small business collaborate without stepping all over each other's toes. At a small business there are often many small documents per project — estimates, contracts, project plans, budgets — and team members frequently have to open and edit them, with all sorts of problems happening if two people edit a file at once. Even if a sharing service is smart enough to keep both versions of the file created, most small-business software (like word processors, spreadsheets, estimating software, or billing systems) has no way to compare — much less to merge! — the changes in two rival versions of a file that two people edited at the same time without each other's knowledge. So, my question: are their cloud-based file sharing solutions that not only provide a virtual network drive that people can access, but that also let users lock files — even if it's not a real lock but just a flag or indicator — that could possibly prevent remote workers from both editing the same file at once? Having one person wait for another person to finish editing is a very, very small inconvenience compared to the hour or more than it can take to compare two estimates by hand until you find and resolve the rival changes. Given this fact, I am surprised that almost none of the popular file sharing solutions seem to recognize this problem and provide some solution! Does anyone know of a service that does?

  Read the article

• Acer LCD says "no signal"

  - by Ken

  I have an Acer 24" LCD (model "AL2423WDR") that's about 3 years old. It worked perfectly for most of its lifetime so far. Recently it started giving problems. When I turn it on, it either says "no signal" on the display, or the power light goes yellow (as if in power-saving mode). This happens with both DVI and VGA (both of which worked fine before), and stranger still, the 4 buttons on the front, for accessing the on-screen menus, don't do anything. I've also tried different computer hardware and software (PC/Mac, Linux/MacOS), but nothing has worked. I've tried power-cycling it (with both the power button and the power switch), and also unplugging it entirely. The nonworking buttons suggest to me an issue with the firmware. I found a place on Acer's website that says I can send it in to have it fixed, at my expense, but I'll avoid that if I can. Is there a way to fully reset it manually? Or is there something else I can try?

  Read the article

• Azure's Ubuntu 12.0.4 fails to install PHP5

  - by Alex Kennberg

  Similar to this article from Azure themselves: http://www.windowsazure.com/en-us/manage/linux/common-tasks/install-lamp-stack/ I am trying to install PHP5 on Ubuntu 12.0.4 virtual machine. However, it fails installing the ssl-cert. $ sudo apt-get install php5 Reading package lists... Done Building dependency tree Reading state information... Done php5 is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 49 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up ssl-cert (1.0.28) ... Could not create certificate. Openssl output was: Generating a 2048 bit RSA private key ............................+++ ...................................................................................................................+++ writing new private key to '/etc/ssl/private/ssl-cert-snakeoil.key' ----- problems making Certificate Request 140320238503584:error:0D07A097:asn1 encoding routines:ASN1_mbstring_ncopy:string too long:a_mbstr.c:154:maxsize=64 dpkg: error processing ssl-cert (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: ssl-cert E: Sub-process /usr/bin/dpkg returned an error code (1) Any tips appreciated.

  Read the article

• CentOS 5.5 remote kickstart installation stalls at "Starting install process." How to debug?

  - by ewwhite

  Hello, I'm having a difficult time with a remote CentOS 5.5 kickstart installation on an HP ProLiant DL360 G6. This is in an environment where I maintain an internal CentOS yum repository. The kickstart installation and post scripts have been tested and normally work. This hardware is also common in this environment, so I do not believe that it is a factor. Unfortunately, I'm having problems with a specific server install. The system is remote to the yum repository at a distance of 500 miles. They are connected over a private low-latency 100-megabit layer 2 connection (26ms round-trip). I'm mounting the 10mb CentOS 5 netinstall ISO image via an HP ILO remote console. The initial boot parameters are: linux ks=http://yum.abctrading.com/prop.cfg ksdevice=eth0 ip=x.x.x.x dns=x.x.x.x netmask=255.255.255.0 gateway=x.x.x.x I'm using the url --url http://ks.abctrading.com/5.5/os/x86_64/ method of installation. This quickly boots into the anaconda installer, pulls the kickstart config and formats the drives. The process eventually halts at the screen below, reading "Starting install process.". Going to the other virtual consoles give the second image below. The process stalls at this point and cannot proceed with the rest of the installation. Running the same kickstart config locally works just fine. I've tried mounting the boot ISO from the console as well as from the ILO2 command line pointing to a locally-hosted boot ISO via http. How can I debug this? Are there any options I've overlooked?

  Read the article

• CPU / Affinity mask problem in SQL 2005

  - by Robert Moir

  Hi folks, Having a problem with a SQL Server which was virtualised. The CPU mask was set on the physical host for some reason and now advanced options are not available. So I need to reconfigure the CPU affinity mask settings - which are advanced options, so this is blocked because of the affinity mask issue. I've tried doing this from the SQL server in single user command line mode, I've googled and found lots of people with similar problems but no real solution. I'm stumped. Any ideas? Sample commands and output from query analyser below. sp_configure 'show advanced options', 1 GO RECONFIGURE WITH OVERRIDE GO sp_configure 'affinity mask', 0x00000000 GO RECONFIGURE GO ----------------------------------------- Configuration option 'show advanced options' changed from 0 to 1. Run the RECONFIGURE statement to install. Msg 5832, Level 16, State 1, Line 1 The affinity mask specified does not match the CPU mask on this system. Msg 15123, Level 16, State 1, Procedure sp_configure, Line 51 The configuration option 'affinity mask' does not exist, or it may be an advanced option.

  Read the article

• windows 7: Event 55 The file system structure on the disk is corrupt and unusable

  - by Radio

  Here is a real bad one! Windows 7 RTM with SP1 installed [Version 6.1.7601]. Recently tried to delete some folder on my hard drive and Windows prompted "Error 0x80070570: The file or directory is corrupted and unreadable", and at the same time placed an Event 55 describing "The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on \Device\HarddiskVolume2." Ran chkdsk, first with /f option, then with /r option. Result in both cases was: no errors found, 0 bad sectors. No problems chkdsk found at all! Went through StackExchange, Google and spent over 6 hours on this. Still cannot figure out the problem. Re-installing/Re-Formatting is not an option! What did I try: Hotfix - Windows6.1-KB982927-x64.msu - gave me an error about incompatibility with my computer, however it totally matches my system. CRC of hotfix was ok. Windows Repair Console found startup errors and fixed those, but this didn't help an issue, even by running chkdsk c: /R from it. http://support.microsoft.com/kb/246026 does not promise anything good. sfc /scannow does not help too. Replaced hard drive by cloning an old one using True Image, repeated all steps above. At the same time, some minor glitches started to appear in my Windows, like side panel and notification area settings are getting reset. Goal is to delete the folder and get rid of Event 55. Sounds like NTFS bug. Please help. This is completely ridiculous.

  Read the article

• Need for explanation: NetBIOS over TCP/IP on VMware network adapter disturbs access to network share

  - by gyrolf

  (Moved here from StackOverflow) Some time ago nearly all workstations in our team (Windows XP SP2) exhibited intermittend but frequent delays when accessing shares on the network. Typically the first access to a share which hadn't been accessed for some time resulted in a nearly frozen workstation for up to 30 seconds. Then everything started working fine again. Using TCPView from Sysinternals I saw that during this delays there was a connection to the netbios-ssn port on the file server which was in state SYN_SENT. First try: Disable NetBIOS over TCP/IP for the intranet network adapter. Problem solved, but I didn't like to manipulate our centrally managed network configuration for the intranet. Second try: Disable NetBIOS over TCP/IP only for the VMWare network adapter (VMNet1 used for host only communications). Problem solved again! My questions: Why does NetBIOS over TCP/IP on one network adapter disturb NetBIOS over TCP/IP on another network adapter? Is this problem specific to VMWare network adapters? Has anybody else seen this phenomen? Additional information: VMWare Workstation version 6.0.3 At the time I started seriously analysing the problem it was no more possible to find out what had been changed to our systems at the time the problems started.

  Read the article

• Shrink a Volume Group in LVM / Linux in order to install Windows on the freed space

  - by Stephan Kristyn

  I have a Volume Group with Unused space. This 40Gig should become an entidy in order to install Microsoft windows 7 on it. I do not have extra space on the drive - that is why I want to shrink the VG! LVG berta resides on sda2 and consists of lv_root lv_swap unused_space I want it to become lv_root lv_swap and have a seperate entidy made out of unused_space. Microsoft Windows 7 has to get installed on this entidy. I do not understand why Linux made simple things complicated. I utterly hate LVM and think its absolute bollocks. Useful Sources: http://www.centos.org/docs/5/html/Deployment_Guide-en-US/s1-system-config-lvm.html Edit: I found the answer. The necessary steps depict how complicated LVM really is. In my opinion it is best to avoiding LVM until pvresize matures as promised in its man pages. Answer: http://fedorasolved.org/Members/zcat/shrink-lvm-for-new-partition If you run into problems when you want to remove lvswap even if in resuce mode, then try swapoff /dev/vg_1/lv_swap lvchange -an /dev/vg_1/lv_swap

  Read the article

• Mac OS X - configuring ntpd server with on LAN with D-Link DIR-655

  - by Mark C

  Hey all, This question is pretty specific, but I hope someone will have seen this error elsewhere. I a configuring a machine running OS X 10.5.8 to be an NTP server for machines connected to a LAN that is not connected to the Internet. I am not too worried about knowing the "right" time on all the machines, but rather worried about making sure everyone has the same notion of time. I configured the NTP daemon on Mac by turning on the Set date and time automatically in System Preferences, using the server's clock, 127.127.1.0 as the reference clock. I figured I should see if the server can NTP query itself before proceeding to the clients. The weird part is when I run the ntpq -p command in a command-prompt when connected to my D-Link DIR-655 (firmware: 1.33), it hangs for about a minute or so each time before finally giving me some output. I thought the problem might have to do with Port Forwarding, so I configured the router to forward port 123 for the IP of the server, but that did not improve the situation. When I run the ntpq -p command on my school's network, on a Linksys WRT54G router, or with the wireless Airport card turned off - I have absolutely no problems - the command returns a response instantly. Is this normal? I can see why a query might take a minute or so, but I don't understand why one router does it faster than the other. I tried messing around with the ntp.conf file adding the burst, minpoll, and maxpoll options: server 127.127.1.0 burst minpoll 4 maxpoll 5 Figuring that perhaps I am polling too often and the configuration file is slowing me down, but even with this, the ntpq still hangs on the D-Link DIR-655, but does just fine on the other routers. Any thoughts on where the lag is coming from or if the lag is even a problem?

  Read the article

• ifcf-ethx problem

  - by Shahmir Javaid

  Every time i run service networkd restart This is what i get Shutting down interface eth0: Device state: 3 (disconnected) [ OK ] Shutting down interface eth1: [ OK ] Shutting down loopback interface: Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown [ OK ] Bringing up loopback interface: Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown [ OK ] Bringing up interface eth0: ** (process:12951): WARNING **: fetch_connections_done: error fetching user connections: (2) The name org.freedesktop.NetworkManagerUserSettings was not provided by any .service files. Active connection state: activating Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/1 state: activated Connection activated [ OK ] Here is my ifcfg-eth0 # Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller DEVICE=eth0 BOOTPROTO=dhcp DEFROUTE=yes DHCPCLASS= HWADDR=xxx IPV4_FAILURE_FATAL=yes IPV6INIT=no ONBOOT=yes OPTIONS=layer2=1 PEERDNS=yes PEERROUTES=yes TYPE=Ethernet UUID=xxx And my ifcfg-eth1 # Intel Corporation 82541PI Gigabit Ethernet Controller DEVICE=eth1 HWADDR=xxx ONBOOT=no And my ifcfg-lo DEVICE=lo IPADDR=127.0.0.1 NETMASK=255.0.0.0 NETWORK=127.0.0.0 # If you're having problems with gated making 127.0.0.0/8 a martian, # you can change this to something else (255.255.255.255, for example) BROADCAST=127.255.255.255 ONBOOT=yes NAME=loopback Any ideas?

  Read the article

• Puppet Decentralized Setup

  - by paul.tw

  I want to migrate my existing Puppet setup from master/client to a decentralized solution. I know other solutions, such as Ansible are easier to setup for that purpose, but I really want to stay with Puppet. I found "supply_drop"(https://github.com/pitluga/supply_drop) on github, so I followed the instructions and did the following: rvm gemset create testing rvm use 1.9.3@testing gem install supply_drop The output is the following: [m@ms-MacBook-Pro:~ $ irb 1.9.3-p547 :001 require 'supply_drop' NameError: uninitialized constant Capistrano from /Users/m/.rvm/gems/ruby-1.9.3-p547@testing/gems/supply_drop-0.17.0/lib/supply_drop/tasks.rb:1:in `' from /Users/m/.rvm/rubies/ruby-1.9.3-p547/lib/ruby/site_ruby/1.9.1/rubygems/core_ext/kernel_require.rb:55:in `require' from /Users/m/.rvm/rubies/ruby-1.9.3-p547/lib/ruby/site_ruby/1.9.1/rubygems/core_ext/kernel_require.rb:55:in `require' from /Users/m/.rvm/gems/ruby-1.9.3-p547@testing/gems/supply_drop-0.17.0/lib/supply_drop.rb:10:in `' from /Users/m/.rvm/rubies/ruby-1.9.3-p547/lib/ruby/site_ruby/1.9.1/rubygems/core_ext/kernel_require.rb:135:in `require' from /Users/m/.rvm/rubies/ruby-1.9.3-p547/lib/ruby/site_ruby/1.9.1/rubygems/core_ext/kernel_require.rb:135:in `rescue in require' from /Users/m/.rvm/rubies/ruby-1.9.3-p547/lib/ruby/site_ruby/1.9.1/rubygems/core_ext/kernel_require.rb:144:in `require' from (irb):1 from /Users/m/.rvm/rubies/ruby-1.9.3-p547/bin/irb:12:in `' Since that doesn't work without problems, I was wondering which alternatives are there available to do the same. Do you have any suggestings?

  Read the article

• hosts file seems to be ignored

  - by z4y4ts

  I have almost fresh Ubuntu desktop box. OS was installed two weeks ago and updated from karmic repositories. Last week I had no problems with DNS. But this week something had changed. I'm not sure what and when, and not sure whether I changed any configs. So now I have some really weird situation. According to logs name resolving should work normally. /etc/hosts 127.0.0.1 localhost test 127.0.1.1 desktop /etc/host.conf order hosts,bind multi on /etc/resolv.conf # Generated by NetworkManager search search servers obtained via DHCP nameserver 192.168.0.3 /etc/nsswitch.conf passwd: compat group: compat shadow: compat hosts: files mdns4_minimal [NOTFOUND=return] dns mdns4 networks: files protocols: db files services: db files ethers: db files rpc: db files netgroup: nis But if fact it is not. user@test ~ping test PING localhost (127.0.0.1) 56(84) bytes of data. [skip] Pinging is ok. user@test ~host test test.mydomain.com has address xx.xxx.161.201 But pure I suspect that NetworkManager might cause this misbehavior, but don't know where to start to check it. Any thoughts, suggestions?

  Read the article

• Recovering a damaged microSDHC

  - by djechelon

  I just bought from eBay a Kingston 32GB microSDHC that was advertised as defective. The seller said that there could be formatting problems or with transfer of large files. Unfortunately, when I got it, it was a total mess. My Nikon camera doesn't read it at all (OK, maybe it doesn't support 32GB) My Linux laptop doesn't mount it: can't read superblock The same laptop refuses to mkfs.msdos because it failed whilst writing reserved sector The same laptop, under Windows, doesn't read nor format the card HTC HD2 mounts the MMC, allows me to write via USB, but is unable to open the just written files OK, folks, now you would say I would have to go through Paypal complaint... that's not that easy. I consciously bought a half-price card that was known to show some defects, and Paypal complaints take time. Obviously, I can't accept somebody sold me a completely use-less computer decoration. So I'll keep it as last option. My question is Do you know a way, under either Linux or Windows, to thoroughly scan, test and possibly repair memory cards, even if I have to lose some percentage of space because of bad sectors? If I can keep at least half of the card intact it would certainly be fine. I used to do broken sector marking with hard disks in the past. I almost forgot: MONSTR:/home/djechelon # fsck /dev/mmcblk0p1 fsck from util-linux-ng 2.17.2 dosfsck 3.0.9, 31 Jan 2010, FAT32, LFN Read 512 bytes at 0:Input/output error

  Read the article

• Cannot connect with Cisco VPN but can connect with ShrewSoft VPN

  - by rodey

  EDIT: We connected an air card to the computer to use a different Internet connection and using the Cisco software, we were able to successfully connect to our VPN server. I just don't understand why the ShrewSoft VPN client would connect but the Cisco connection won't. I'm not our network admin so sorry if I butcher some of the terminology. I have a computer at remote site that connects to our network through Cisco VPN. It uses the Cisco VPN software to do so. The problem is that the computer at this site cannot connect to our VPN because it is getting error "Reason 412: The remote peer is no longer responding." To see if perhaps something on their network was blocking the connection, I installed the ShrewSoft VPN client on the computer, imported our .pcf file and connected with no problem. I have tried two different versions of the Cisco VPN software (4.8.0.* and 5.0.03.*) and have the same problem. I installed Wireshark on the computer and have confirmed (while trying to connect through Cisco) that the computer is trying to contact the VPN server but is not receiving a response. We are not having any other problems regarding users not being able to connect. I'm at a loss at what else to check. I'll be monitoring this and have access to the computer at any time.

  Read the article

• Red Hat server minimal install

  - by chmeee

  In a farm of virtualized Red Hat servers, there's the need to install a minimal system for security reasons. Minimal installs have serveral advantages (even no security related): Lees exposure to vulnerabilities (if you don't need it, don't install it) Better update process (less packages to update, less probability of breaking the system) Better performance (no unneeded daemons or processes) The less software you have the easier it is to harden the system Unfortunately, this is not easy because the "Minimal Installation" on Red Hat contains lots of unnecessary packages. There is an added challenge as the farm is running Oracle iAS. I've been told that iAS has dependencies with local graphical envieronment. So finally every server in the farm has gnome, X, etc. I've been searching the web and one solution seems to be making a kickstart script that will intall only the necessary packages. But I find this difficult and have several doubts about how to maintain the system dependencies afterwards. How do you install minimal Red Hat servers? Is it Ok to use kickstart or will I have dependency problems in the installation or in updates? Is there any way to avoid installing the graphical environment for iAS?

  Read the article

• "Server Unavailable" and removed permissions on .NET sites after Windows Update [closed]

  - by andrewcameron

  Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

  Read the article

• Setting up MongoDB in High Performance Computing LSF linux cluster

  - by Dnaiel

  I am trying to run mongo in a LSF cluster computing environment where I have no admin control. Our sysadmin installed mongodb, but it is not running. Any ideas on what should I ask the server admin to do for it to run? Or if I could run it locally? [node1382]allelix> mongod --dbpath /users/dnaiel/ma/mongodb/ Tue Oct 2 21:33:48 [initandlisten] MongoDB starting : pid=22436 port=27017 dbpath=/seq/epigenome01/allelix/ma/mongodb/ 64-bit host=node1382 Tue Oct 2 21:33:48 [initandlisten] Tue Oct 2 21:33:48 [initandlisten] ** WARNING: You are running on a NUMA machine. Tue Oct 2 21:33:48 [initandlisten] ** We suggest launching mongod like this to avoid performance problems: Tue Oct 2 21:33:48 [initandlisten] ** numactl --interleave=all mongod [other options] Tue Oct 2 21:33:48 [initandlisten] Tue Oct 2 21:33:48 [initandlisten] db version v2.2.0, pdfile version 4.5 Tue Oct 2 21:33:48 [initandlisten] git version: f5e83eae9cfbec7fb7a071321928f00d1b0c5207 Tue Oct 2 21:33:48 [initandlisten] build info: Linux ip-10-2-29-40 2.6.21.7-2.ec2.v1.2.fc8xen #1 SMP Fri Nov 20 17:48:28 EST 2009 x86_64 BOOST_LIB_VERSION=1_49 Tue Oct 2 21:33:48 [initandlisten] options: { dbpath: "/users/dnaiel/ma/mongodb/" } Tue Oct 2 21:33:48 [initandlisten] journal dir=users/dnaiel/ma/mongodb/journal Tue Oct 2 21:33:48 [initandlisten] recover begin Tue Oct 2 21:33:48 [initandlisten] info no lsn file in journal/ directory Tue Oct 2 21:33:48 [initandlisten] recover lsn: 0 Tue Oct 2 21:33:48 [initandlisten] recover /seq/epigenome01/allelix/ma/mongodb/journal/j._0 Tue Oct 2 21:33:48 [initandlisten] recover cleaning up Tue Oct 2 21:33:48 [initandlisten] removeJournalFiles Tue Oct 2 21:33:48 [initandlisten] recover done Tue Oct 2 21:33:48 [websvr] admin web console waiting for connections on port 28017 Tue Oct 2 21:33:48 [initandlisten] waiting for connections on port 27017 It basically waits forever and cannot start mongodb. These servers are not webservers but they do have network access, it's a cloud computing LSF environment system. Any advice would be welcome, thanks in advance.

  Read the article

• vmdk Recovery after migration from 3.5 to 4 and fallback tentative.

  - by olgirard

  Hy, I've tryed to migrate some VM from my 3.5i environment to a brand new vSphere 4.0 U1. The two platforms are running simultaneously, sharing the same SAN. I Migrate my VM by stopping it, unregistering in vcenter (esx ver. 3.5, i call it esx3), register in vSphere (esx ver. 4, i call it esx4), and migrate upgrade virtual hardware before powering it up (First mistake). vMotion was enabled on esx4, seem to be a second mistake. After a day or so, i encountred problems joigning the esx server (esx4) and decided to unregister my server for esx4 and fallback to esx3. esx3 refused to boot, i supposed this was due to virtual hardware in Version 7 so i recreated a new VM pointing to the vmdk of the old VM. Everithing seemed fine until i log into the server and discover that i was running on the original disk ith every snapshots ignored even those created on esx3. I tried to reboot VM on esx4 but VM doesn't power up because "The parent virtual disk has been modified since the child was created". I've got a copy of a later state of the drive but generated between two snapshots (ovf generated with canverter standalone) as a backup. Do i have a chance to recover at least some files on the virtual drive or (as i tink) all is played, i've done enought mistakes for this time. Thanks for your help.

  Read the article

• Workstations cannot see new MS Server 2008 domain, but can access DHCP. (solved)

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• Nginx proxy hangs when proxiing to itself

  - by Thomas

  I have Nginx running as a proxy for a number of services including a Geoserver running on port 8080 with the following config: location ^~ /wms/ { rewrite ^/wms/(.*)$ /geoserver/ows$1 break; proxy_pass http://127.0.0.1:8080; proxy_connect_timeout 60s; proxy_read_timeout 150s; } and a proxy service to avoid SOP problems which works as follows: location ^~ /proxy/?targetURL= { rewrite ^/proxy/?targetURL=(.*)$ $1 break; proxy_pass $1; proxy_connect_timeout 60s; proxy_read_timeout 150s; } My web server is also under the same domain, ran by a jetty on port 8888, handled by the same proxy. location / { proxy_pass http://127.0.0.1:8888; proxy_connect_timeout 60s; proxy_read_timeout 150s; } From my web application I make WMS server calls for data via my proxy service. It works fine for external servers but it hangs when I call my own internal geoserver. My geoserver proxy works fine, I can make WMS service queries with the said URL. The call that hangs is basically: http://mywebappdomain.com/proxy/?targetURL=http://mywebappdomain.com/wms/?my_set_of_parameters Which means that the proxy rule applies and the WMS service is called from the same server. Is there an issue with proxying over itself?

  Read the article

< Previous Page | 436 437 438 439 440 441 442 443 444 445 446 447  | Next Page >