Search Results

Search found 19676 results on 788 pages for 'hardware interface'.

Page 442/788 | < Previous Page | 438 439 440 441 442 443 444 445 446 447 448 449  | Next Page >

• SpinRite and USB blues - does a solution exist?

  - by Peter Mortensen

  I use SpinRite to recover hard disks and their content, and to a lesser degree for preventive maintenance. However, if a USB drive (USB thumb drive and/or external hard disk with a USB interface) is connected when SpinRite scans for devices, then SpinRite never finishes/hangs. The work-around is of course to disconnect the drive, but there is value in being able to use SpinRite on USB drives. Some external drives have no screws and it is difficult to take out the hard disk without damaging the casing. And for those that have it would save the disassembling time. Is there a way to fix this problem (e.g. BIOS changes or a modified SpinRite boot CD) without resorting to floppy disks?

  Read the article

• QoS / PBR Routing Questions

  - by Bernard

  I have a 50Mbs Satellite link and a 10Mbs Microwave link supplying a very remote location. Behind these links, I have a 6,400 seat network - with about 3,000 signed in at any one time. My goal is to send all of the Voip traffic (Google Chat, Magic Jack, Skype, Speakeasy, Vonage, Vonage PC, Yahoo) through the microwave link which has 100ms latency. The rest of the traffic can utilize any remaining bandwidth of the microwave link with excess being diverted to the higher latency (600ms) satellite connection. The problem I've had so far is that most automatic routing configurations weigh the bandwidth heavily for preference - and I'm only wanting latency considered. Additionally, I don't know if this can even be handled with the routing hardware I have at my disposal (Cisco 3640, 3745, & 3845). Any recommendations (or really good starting points) would be greatly appreciated.

  Read the article

• Choosing a very basic Linux distro with minimal boot time?

  - by user30961

  I've had Ubuntu for a year now, like it but it doesn't match my needed configuration for my old laptop. So... I am using Linux mainly for webapps so I don't care much about user interface. What I need is a distro which is small enough to install on a SD memory card (or USB) since I am removing the hard drive, all my data is in the cloud. I also want it to have as short boot time as possible. I tried Puppy Linux and it seems ok but it had preinstalled looots af small apps I don't need, I would really like to have a distro with minimal preinstallations and add them on my own. So what are my choices and why would you recommend these?

  Read the article

• Xenserver boot error

  - by Adrian

  I'm trying to get Xenserver 5.5 running on a spare computer here, hardware specs: Intel Q6600, 4GB Ram, and Gigabyte GA-P35-DS3R motherboard Xenserver itself installs fine onto a 150GB sata hdd, however it fails to boot whatsoever, giving this garbled mess: http://img697.imageshack.us/img697/9918/biosi.jpg it's not frozen because if I press enter it just prints a different garble and it also says "could not find kernel image". The strangest thing is if I put that hdd in my desktop and assign it to a VMWare desktop vm (under the ESX profile no less) it boots perfectly... leading me to believe there are no problems with the install or the hdd itself. From what I can tell the error seems to be occuring completely seperately to Xenserver, in the bootloader extlinux?. If there was a motherboard compatibility issue I would think it would also have manifested during installation, and the fact the problem seems to be with the booting into Xen makes me doubt this. Any ideas guys? (I'm using Xen because it can do PCI passthrough without VT-d.)

  Read the article

• Static route in conflict with a default route

  - by Ossan Sokiv

  Hi guys, I have a default route configured. 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.1 I'd like to add a static route to pass traffic destined for 192.168.1.51 via a load balancer's redundant virtual interface at 192.168.1.2. ip route add 192.168.1.51 mask 255.255.255.255 via 192.168.1.2 When I try to add the static route I get this error. Error: either "to" is duplicate or "default" is garbage." It doesn't want to add the static route because it's in conflict with the default route. Is there a way around this? Regards Ossan

  Read the article

• Keyboard automatically disconnects and reconnects

  - by Algorithms

  The problem i am facing is the keyboard (USB) automatically disconnects when there is a fluctuation in the power supply to the speaker. The speaker and the pc both draw power from a apc ups. The fluctuation occurs because the speaker plug is not tightly connected to the ups power outlet. It is okay for normal work, but a accidental jerk causes the fluctuation. However after some amount of time (usually within 5 seconds) the keyboard automatically reconnects and windows plays the sound of hardware connected. This problem will also occur if I manually take out the speaker power cable from the ups power outlet. My question is whether the problem I am facing is due to electrical issues, or due to software problems. PC config: OS : Windows 7 Ultimate UPS : APC 600 VA PSU : Corsair TX 650 Speaker : Realtek

  Read the article

• DHCP Client Can't Find DHCP Server

  - by leeman24

  I currently have 3 machines: CentOS (router) eth1 - 18.0.168.1 eth2 - 145.165.34.1 Windows Server 2008 (server) 18.0.168.2 DHCP scope - 145.165.34.10 - 145.165.34.20 Windows 7 (client) Supposed to use DHCP I can't get my Windows 7 client to get an address from the Windows Server 2008 DHCP server. Every network interface can ping each other (ex. 18.0.168.2 can ping 18.0.168.1 & 145.165.34.1 and the other way around). My Linux machine acting as the router has default IP tables. Other than this command which may or may not be right: iptables -I INPUT -p udp -d 18.0.168.2 --dport 67:68 -j ACCEPT I have also tried it after I flushed the IP tables. I was looking at the dhcrelay command but it seems CentOS doesn't have it and I am not even sure how to use it.

  Read the article

• Why is this LTO4 Tape-drive not working

  - by Tim Haegele

  # modprobe mptsas # dmesg [ 4274.796796] scsi target7:0:0: mptsas: ioc1: delete device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4274.939579] mptsas 0000:01:00.0: PCI INT A disabled [ 4280.934531] Fusion MPT SAS Host driver 3.04.12 [ 4280.934552] mptsas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4280.934692] mptbase: ioc2: Initiating bringup [ 4281.490183] ioc2: LSISAS1064E B3: Capabilities={Initiator} [ 4281.490203] mptsas 0000:01:00.0: setting latency timer to 64 [ 4293.555274] scsi8 : ioc2: LSISAS1064E B3, FwRev=011e0000h, Ports=1, MaxQ=277, IRQ=16 [ 4293.574906] mptsas: ioc2: attaching ssp device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4293.576471] scsi 8:0:0:0: Sequential-Access IBM ULTRIUM-HH4 B6W1 PQ: 0 ANSI: 6 [ 4293.578549] st 8:0:0:0: Attached scsi tape st0 [ 4293.578550] st 8:0:0:0: st0: try direct i/o: yes (alignment 512 B) [ 4293.578577] st 8:0:0:0: Attached scsi generic sg5 type 1 # mt -f /dev/st0 status mt -f /dev/st0 status mt: /dev/st0: rmtopen failed: Input/output error # dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 dd: opening `/dev/nst0': Input/output error I am running debian squeeze 2.6.32-5-amd64 #1 SMP Sun May 6 04:00:17 UTC 2012 x86_64 GNU/Linux Server is Fujitsu TX140 with Controller Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS Tape+Hardware is new.

  Read the article

• Using tshark to generate traffic logs every X seconds

  - by Sridhar Iyer

  I'm trying to use tshark to maintain a running history of all the packets that are going through an interface, for say 30 seconds. I want it to be human readable. This is a linux machine, and without mucking too much into the netstack source (which I can do if push comes to shove), I was wondering if I can use tshark to this. tshark has a -b duration:10 -b files:2 which I can use to generate a rotating set of 2 files, but I don't know which format it is printing the file in or how to read it.

  Read the article

• Server Security

  - by mahatmanich

  I want to run my own root server (directly accessible from the web without a hardware firewall) with debian lenny, apache2, php5, mysql, postfix MTA, sftp (based on ssh) and maybe dns server. What measures/software would you recomend, and why, to secure this server down and minimalize the attack vector? Webapplications aside ... This is what I have so far: iptables (for gen. packet filtering) fail2ban (brute force attack defense) ssh (chang default, port disable root access) modsecurity - is really clumsy and a pain (any alternative here?) ?Sudo why should I use it? what is the advantage to normal user handling thinking about greensql for mysql www.greensql.net is tripwire worth looking at? snort? What am I missing? What is hot and what is not? Best practices? I like "KISS" - Keep it simple secure, I know it would be nice! Thanks in advance ...

  Read the article

• Double default gateway ubuntu server

  - by Elena

  I've just installed an Ubuntu server 9.10 on an EEEBox. This is my /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback auto wlan0 iface wlan0 inet static address 192.168.48.16 netmask 255.255.248.0 wireless-essid mynet auto eth0 iface eth0 inet static address xx.xx.xx.xx netmask 255.255.255.224 gateway xx.xx.yy.yy When I restart /etc/init.d/networking, I can access the eth0 ip address from the internet and I can ping the machines in my wifi network mynet. Everything works fine and I have one default gateway. But after some time if I check again the route I just find two default gateways: one is correct and is the previous one, but the other is the one of the wifi network. I have a quite low signal of mynet where my server is and sometimes the wifi just disconnect and then reconnect again. Then I think that this can be a problem and the dhcp of the wifi net, when reconnecting it also add a default gateway. Any idea on how to resolve this issue?

  Read the article

• Installing Windows Server 2003 on AMD environment

  - by santhosh kumar

  Hi all, Our organisation we have 25 computers and we are trying to setup Windows Server 2003. We are planning to configure Active Directory NAT DNS server Visual Studio Team Foundation Server Subversion (SVN) Trac (Bug tracking tool) FTP server And our Hardware configuration is AMD Athlon 64 X2 Dual (Core processor 5600+, 2.60 GHz) Asus motherboard (M2N series) Transcend 4 GB RAM (800 MHz) 500 GB Hard Disk (RAID enabled) But my colleague is advising me AMD won't suite for servers platforms, and use Intel environment. Also they telling we can't install all the services to one server. I got confusion what to do?... Is really can`t install above services to AMD computer? Thanks...

  Read the article

• Dynamips Virtual Router not pinging external host after bridging

  - by maiky

  I have setup a virtual router image with dynamips and setup bridging between tap0 interface of the virtual router and eth0 and br0 with commands [root@cisco_host]# brctl addbr br0 [root@cisco_host]# ifconfig br0 up [root@cisco_host]# ifconfig eth1 0.0.0.0 [root@cisco_host]# brctl addif br0 eth1 [root@cisco_host]# ifconfig br0 192.168.0.100 netmask 255.255.255.0 up In dynagen configuration I have: f0/0 = NIO_tap:tap0 So, [root@cisco_host]# brctl addif br0 tap0 [root@cisco_host]# ifconfig tap0 up router(config)#int fa0/0 router(config-if)#ip address 192.168.0.101 255.255.255.0 router(config-if)#no shutdown After the configuration above I was expecting that from inside the router I could ping an external machine with IP 192.168.0.1 Actually from the host I can ping the external host 192.168.0.1 as well as 192.168.0.100 and 192.168.0.101. So what am I missing here? tap0 is bridged with br0 and in turn with eth1. So why the router is not pingable from 192.168.0.1 and vice-versa??

  Read the article

• WD My Passport Essential SmartWare External Hard Drive

  - by Acer

  Hi Ive been gifted a My Passport SmartWare External Hard Drive(500gb). I used it and it works fine and installed WDSmartWare The Second time i used it,still fine,but I took it out without using the "Safely Remove Hardware" So the third time I used it,there's a bubble come out that says: USB Device Not Recognized One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it.For assistance in solving the problem, click this message. I tried connecting it to other USB Ports but it didn't work I tried Uninstalling WDSmarWare and connect it but it didn't work Please help me I like this hard drive so much and I spoilt it easily XD P.S I think about 13% has been used up in the Hard Drive P.S.S Other USBs can work fine in the computer P.S.S.S I tried connecting it to other computer and works fine OMG

  Read the article

• Windows XP/7: custom routing for VPN connection

  - by Peter Becker

  We are dealing with a badly configured VPN connection from a vendor, which set up the default gateway but doesn't route traffic anywhere beyond their VPN zone. I managed to do some ad-hoc routing to configure a computer in a way that it can reach the vendor's VPN, our local network as well as the internet. I then tried to turn this into a script, but that failed since the interface number of the VPN changes on every connection. Is there a way in Windows XP and/or Windows 7 to configure custom routing on the client side of a VPN connection? What I would like to do is to have a script running just after the connection comes up that changes the routing table (similar to an ifup script on UNIX).

  Read the article

• Backup strategy for Windows Server 2008 R2 and Hyper-V

  - by winserveradmin

  I am in the process of planning a Hyper-V deployment with SCVMM 2008 R2. I have several VMs on VMWare Player (temporary solution) for stuff like Sharepoint 2007, 2010, and a couple of other server apps. I want to develop a resilient backup plan for this. On the software side, Data Protection Manager 2010 will support all of the server apps I run (sQL Server 2008 R2, Sharepoint, Exchange, etc). But on the hardware side (storage), what is the best way to go? Drobo seems to have issues with Hyper-V juding by a few threads on here and doesn't support DPM 2010 (which is in beta anyway) but not even the 2007 version (see http://www.drobo.com/support/best_practices.php). What storage device would work well? Do I need a home server or just an external usb drive? Capacity wise, 2tb will probably be best so I can have a small archive and implement a round-robin system. Thanks

  Read the article

• Is it possible to a VM inside a VM (e.g., KVM on Vmware)?

  - by lorin

  I'd like to do some development on Eucalyptus, an open source project which provides an Amazon EC2 interface for launching virtual machine instances on a collection of privately managed nodes. I'd really like to be able to do some of the development on my desktop, rather than having to deploy Eucalyptus on our shared local cluster each time I make a change to the source code. (Especially since there are a group of us sharing that test cluster). Unfortunately, my desktop machine is a Mac, which won't run Eucalyptus natively. I do have VMWare Fusion, and it would be really nice if I could do my Eucalyptus testing inside a VMWare instance. The problem is, to test out Eucalyptus, it will have to launch (KVM or Xen) VM instances. I've got no idea if it's possible to actually launch a KVM or Xen instance inside a VMWare instance.

  Read the article

• Gre Tunnel Cisco Linux traffic forwarding

  - by mezgani

  I setup a gre tunnel a cisco router and a Linux machine, the tunnel interface in the Linux box named pic. Well i have to forward traffic coming from cisco through the Linux box. the rules i've set in the Linux box is described as follow: echo "1" /proc/sys/net/ipv4/ip_forward iptables -A INPUT -p 47 -j ACCEPT iptables -A FORWARD -i ppp0 -j ACCEPT iptables -A FORWARD -i pic -o ppp0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i ppp0 -o pic -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE I see the traffic coming from tunnel and forwarded to internet but no reply from sent packet. May i miss something like a routing rule.

  Read the article

• WHEA_UNCORRECTABLE_ERROR BSOD - what is wrong?

  - by Arcane

  Hello I have a problem with my PC getting the WHEA_UNCORRECTABLE_ERROR bsod. It is a few months old pc. I am not overclocking or changing anything in bios, but sometimes (this is my third time) I get this bsod out of nowhere. This last time I was just watching some stream on twitch when the pc suddenly crashed. I have everything up to date in windows update and every other driver as well. Everything in Open hardware Monitor seems ok. Right now as of 10 min after the crash, the CPU temp is at 38°C, fans are at 1400RPM I am using Windows 8.1 Pro 64b. Here are my spec: Intel i5-4570 CPU @ 3.20GHz, Kingston HyperX 8GB DDR3 1600 XMP, GeForce GTX 660 with 340.52 drivers, Corsair VS450 power supply, Gigabyte GA-H87-HD3 you can see the BSOD dump here: https://www.dropbox.com/s/88i1q2nnqnpzux1/082514-29656-01.dmp?dl=0 Can anybody tell me what is wrong?

  Read the article

• Load-balancer options

  - by toolkit

  I am looking at a number of possible options for load-balancing. So far, I am constrained to the following options: DNS server load-balancer, balancing to a cluster of tomcat servers, with terracotta for session replication. Pros - don't have to buy new kit. Cons - DNS lb can keep directing to a broken server. Hardware load-balancer, direct to cluster of tomcat servers. Pros - could have second box for failover lb. Cons - expense. Apache server load-balancer. Pros - apache's lb polls for broken servers. Cons - apache server is single point of failure, plus need to buy another server. Are there any other options I should consider? Thanks. Update: Thanks for all the answers so far +1's all round. Not accepting an answer yet, to keep more ideas coming.

  Read the article

• Primary domain controller has crashed, secondary does not log in

  - by Hosm

  Hi everybody, I had a primary domain controller on machine A and a secondary one on machine B in my AD domain. Due to some hardware/software problems, I decided to migrate the role of primary domain controller to machine B. Unfortunately, machine A has totally crashed and does not boot. Now I can not even log in to machine B (which itself was a controller in the domain). I need to log into machine B then choose it as the primary controller. I already have synced DNS and AD info. when machine A was alive. Anyone can provide an idea?

  Read the article

• Cross platform support for network attached USB hubs?

  - by larsks

  I am looking at network-attached USB hubs in order to run licensed software in a virtualized environment when hardware dongles are required. Are there any solutions that will work with both Linux and Windows? Most of the dedicated devices -- such as the Zonet ZUH2214 or the (oddly expensive) Digi AnywherUSB/2 -- appear to be Windows-only. Linux has the the USB/IP project, for which there appear to be Windows drivers, but the last "News" post on the site was in 2007, so I'm not entirely confident about the viability of the project. Has anyone out there found a solution that will work well in both environments?

  Read the article

• USB to LPT adapter?

  - by Dave

  I'm bummed out, pretty much all of our computers here lack parallel ports. I have an EETools ChipMax programming tool that has one of the old-school Centronics connectors on the back. I figured that someone must make a USB to LPT adapter. Sure enough, I found one from iogear, the GUC1284B that is a USB to Parallel Printer cable. Note the boldface on the Printer. It must connect to a printer -- it isn't some generic USB to parallel interface, unfortunately. Does anyone here know of an adapter that works for parallel devices that aren't printers? I'd hate to have to buy a USB version of the ChipMax when I don't need to use it very much.

  Read the article

• Horizontal scrolling not working in Windows 7 running on MBP using Boot Camp

  - by Rubicon

  Is there a way to enable horizontal scrolling on Windows installed on a bootcamp partition of MBP 13" Core 2 Duo, using a trackpad? I had a look into the Boot Camp Control panel settings, but could not find a setting that suggested this. I used the Boot Camp drivers that came with the MBP in the Mac OS X Install disk. The vertical scroll is working fine, and the horizontal scroll works fine in the Mac world of things, so the hardware is fine. I think maybe there might be an additional install for a driver that we may have to install? Or any update? Thanks in advance for all your help. :)

  Read the article

• Cisco Catalyst 65XX and traffic shaping

  - by Nadz Goldman

  Hello! I have Cisco Catalyst 65XX, many VLANs and about ~1300 users. Users connected to some D-Link switches with second-level management. D-Link switches come to my Cisco Catalyst 65XX by VLANs. So, how I can shape traffic per user? If I use something like this: access-list 145 permit ip any host 192.168.0.1 access-list 145 permit ip any host 192.168.0.2 access-list 145 permit ip any host 192.168.0.3 ... int Gi0/1 traffic-shape group 145 128000 7936 7936 1000 will I have shape traffic per user or it will shape traffic only on interface? I mean - every user will have 128kb/s (per user) or everybody will have 128kb/s ? If it will be for everybody, then what is the solution of my question: how every user can have 128kb/s ?

  Read the article

< Previous Page | 438 439 440 441 442 443 444 445 446 447 448 449  | Next Page >