Search Results

Search found 35444 results on 1418 pages for 'lock down computer'.

Page 442/1418 | < Previous Page | 438 439 440 441 442 443 444 445 446 447 448 449  | Next Page >

• Error 720 on VPN (PPTP) attempt

  - by Andy Shulman

  When I attempt to connect to a server running XP x64 (so essentially Server 2003) using a PPTP connection, it fails with client-side error Registering your computer on the network... Error 720: A connection to the remote computer could not be established. You might need to change the network settings for this configuration. and server-side error Event ID: 20050 The user WINSERV3\Andy connected to port VPN8-1 has been disconnected because no network protocols were successfully negotiated. I have configured the router to pass both TCP packets on 1723 and GRE packets. I have used Wireshark (filtering out ARP, UDP, and all TCP ports other than 1723) to observe the packets received by the server. Wireshark does not explicitly name any protocol GRE, but it does tell me the server sent and received TCP, PPTP, PPP LCP, PPP CHAP, PPP CBCP, and PPP IPCP. The connection seems to go wrong at packet 30, where the protocol is PPP LCP, with the payload of the packet being labeled "Protocol Reject". Obviously, this is going from server to client. This would seem to lead to the conclusion that there is something wrong with my client, which runs Windows 7 Ultimate x64. However, it is able to connect to my house's router, which runs the DD-WRT firmware and is thus a PPTP endpoint. I'm thoroughly at a loss. Please help!

  Read the article

• Can you disable UNC paths in Windows?

  - by Evan

  We are trying to lock down a Terminal Server, and want to remove a commercial package's ability to accept UNC file paths, ie. paths in the app can then only be entered using the windows drive letters. Is there any way to do this in Windows? Can we disallow UNC paths for just the app? Can we disallow UNC paths for the entire Terminal Server session? The intention is to allow the application to only write to certain directories (as mapped in the Terminal Server session). The aim is to prevent the output of files to directories that the users have access to, but are not mapped in the Terminal Server session.

  Read the article

• error exporting data using mysql workbench

  - by Rajneesh Rana

  hi, i have been getting warning of version mismatch when i was trying to export data dump using mysql workbench. So, i copied mysqldump from mysql server folder and placed it in workbench folder. Now when i am trying to export data i am getting error Operation failed with exitcode -1073741819 here is a entry of log 16:31:25 Dumping wordpress (wp_posts) Running: "mysqldump.exe" --defaults-extra-file="c:\docume~1\rajneesh.r\locals~1\temp\1\tmpxau7tz" --no-create-info=FALSE --order-by-primary=FALSE --force=FALSE --no-data=FALSE --tz-utc=TRUE --flush-privileges=FALSE --compress=FALSE --replace=FALSE --host=localhost --insert-ignore=FALSE --extended-insert=TRUE --user=root --quote-names=TRUE --hex-blob=FALSE --complete-insert=FALSE --add-locks=TRUE --port=3306 --disable-keys=TRUE --delayed-insert=FALSE --create-options=TRUE --delete-master-logs=FALSE --comments=TRUE --default-character-set=utf8 --max_allowed_packet=1G --flush-logs=FALSE --dump-date=TRUE --lock-tables=TRUE --allow-keywords=FALSE --events=FALSE "wordpress" "wp_posts" Operation failed with exitcode -1073741819 Please help me with these issues Thank You

  Read the article

• switchless Infiniband between two servers on RHEL 6.3

  - by exfizik

  I have 2 servers running RHEL 6.3 which have 2 port Infiniband cards >lspci | grep -i infini 07:00.0 InfiniBand: QLogic Corp. IBA7322 QDR InfiniBand HCA (rev 02) I'm interested in connecting them directly to each other bypassing an Infiniband switch (which I don't have). Quick googling showed that at least in some configurations it's possible. I installed all RedHat Infiniband packages with yum groupinstall "Infiniband Support". However, ibv_devinfo shows that both ports in each card are down, which indicates that cables are not connected. But the cable is connected, although the LEDs are off on the cards (not a good sign). Another source of confusion for me is that according to this, RedHat doesn't come with OFED packages and I'm slightly hesitant to install them from source due to the lack of RedHat support for them... So where am I going with this? The questions I have are: is it possible to have a switchless/direct Infiniband connection between two servers the way I described above? If it's possible, do I have to use the OFED packages or can I configure everything with just the packages coming with RHEL. Why are the LEDs off on my servers even though the cable is connected? Any additional input/advice/pointers would be appreciated. P.S. I followed this guide for installation instructions. The Infiniband cards are clearly recognized by my OS and the rdma service is running. Update: I have opensm installed. When I run it it says: OpenSM 3.3.13 Command Line Arguments: Log File: /var/log/opensm.log ------------------------------------------------- OpenSM 3.3.13 Entering DISCOVERING state Using default GUID 0x1175000076e4c8 SM port is down and stays at that point.

  Read the article

• IPFW not locking people out

  - by Cole

  I've had some brute-forcing of my ssh connection recently, so I got fail2ban to hopefully prevent that. I set it up, and started testing it out by giving wrong passwords on my computer. (I have physical access to the server if I need to unblock myself) However, it never stops me from entering passwords. I see in /var/log/fail2ban.log that fail2ban kicked in and banned me, and there's a ipfw entry for my IP, but I'm not locked out. I've changed the configuration around, and then tried just using the ipfw command myself, but nothing seems to lock me out. I've tried the following blocks: 65300 deny tcp from 10.0.1.30 to any in 65400 deny ip from 10.0.1.30 to any 65500 deny tcp from 10.0.1.30 to any My firewall setup has a "allow ip from any to any" rule after these though, maybe that's the problem? I'm using Mac OS 10.6 (stock ipfw, it doesn't seem to have a --version flag) Thanks in advance.

  Read the article

• Smart Array P400 battery failure

  - by RobIII

  The P400 Smart Array controller in my HP DL380G5 is indicating: Battery Status: Failed, Replace Battery 1 in the System Management Homepage. Also the IML indicates: POST Error: 1794-Drive Array - Array Accelerator Battery Charge Low I do have several replacement batteries (actually, several controllers including batteries) lying around at work but never had to actually replace one. I am wondering if the battery replacement (swap) could be done hot or if I need to take down my server to do the battery replacement. I have replaced other spare parts like fans and drives before and all those can be replaced hot. I just don't know about the battery of the P400 Smart Array controller. Any help would be appreciated. EDIT1 For those interested: straight from the horse's mouth: With thanks to Frands Hansen pointing it out here. EDIT2 In the end I did just power down, to be on the safe side and because the manual says so, and replace the battery. Couldn't be easier. Unplugged the old one of the end of the cable (not the end connected to the controller) and reconnected a spare one. The replaced battery is now in the server for about an hour and currently (still) recharging. I'm assuming all will end wel.

  Read the article

• Linux accessibility: Slow Keys causing duplicate key strokes

  - by skypanther

  I'm exploring the accessibility features within Gnome and having trouble with Slow Keys. My input is always doubled. Press a key briefly and I get nothing as you'd expect. Press just a bit longer and which ever key I'm pressing is input twice. Hello becomes HHeelllloo. I'm running Debian Lenny 5.0.6, kernel 2.6.26-2-686, GNOME Desktop 2.22.3 running within a VirtualBox session. I did some googling and didn't find others having similar troubles. Maybe it's a vbox thing? Any ideas how to fix this so I don't get the duplicates? It makes it impossible to log back in when the screen lock kicks on!

  Read the article

• iTunes Home Sharing only works one way between 2 WinXP PC's on the same LAN

  - by scunliffe

  Both PC's have the latest iTunes installed. PC (A) can "see" that there is a shared library "B library" but attempts to connect to it return this error message: The shared library "{Username}'s Library" is not responding (-3259) Check that any firewall software running on either the shared computer or this computer has been set to allow communication on port 3689. however the reverse works fine. e.g. PC (B) can "see" shared library "A library" and can access all content. Notes: Both PC's have Home Sharing enabled (turned off/on several times to verify). Both PC's have Windows Firewall turned on, but in the exceptions tab, iTunes is allowed, and Port 3689 is also added as a firewall exception (just in case) Both iTunes accounts have been "authorized" on both PC's Both PC's connect via LAN via D-Link DIR-615 router. In the advanced application rules, iTunes has also been added to allow traffic on port 3689 un-hindered. Is there any other magical setting/configuration option that I should be aware of and set in order to get this to work? I could care less about sharing apps etc. I just want the music sharing to work. Update: Solved! It turns out on PC (B) there were multiple accounts set up. 1 of the accounts had the checkbox checked under the windows firewall "On" option which states "No exceptions" thus even though it was added to the exception list on the main user account, this other account was blocking access.

  Read the article

• Smart card / auditable access for rack KVM tray

  - by Mark Henderson

  Is there such a thing as a KVM Tray for a standard 19" rack whose use can be validated by a smartcard (or some other auditable authentication method)? It looks like we have a security requirement where just because users have a key to the rack doesn't mean they will be allowed to use the console inside the rack, and rather than just lock the console (and keep track of who has keys), we would prefer to be able to audit the actual user that was attached at the KVM. (It's worth mentioning that I'm aware of the Raritan devices, but they surely can't be the only ones) (If these things existed, I don't think half of the tratoirs that somehow manage to infiltrate CTU on the TV show 24 would ever get away with anything)

  Read the article

• How to use Windows mini-dump files?

  - by ekaj

  I have a Mini-ITX Intel DH61AG mobo w/ an Intel i3 processor and 8GB of 1600MHz DDR3 RAM. Anyways, this computer has been crashing kind of frequently. It is not an OS problem, as I have used Ubuntu (and had kernel panics), Windows 7, and Windows 8 (BSODs aren't going to keep me from tinkering =p) Anyways, each of these OSes have had problems, so I ran a HDD check, and I know it is not a heat issue because I tested the processor for a few days when I first put the computer together. When I ran memtest86+, however, I got an error - so I did individual testing, and both chips came back good, did a really intense test with both of them again (took half a day), and no errors. So, I still think the problem could be RAM, but I am not sure - I tested it pretty extensively (might let it run all night again tonight)... which brings me to my point. Could someone explain to me (in simple terms if possible) how to READ the minidump files of Windows computers? I've tried before with a guide I found online, but failed miserably (can't remember guide, either =/). I'm fine with installing the software, I will probably need it sometime in the future as well. I have seen a few other posts on SU that just ask people to post minidump logs, but I feel as if that is too localized. Would someone be able to explain this? Note: If someone knows how to do this, but doesn't want to explain and is still willing to help me, this is the link for the minidump file =p Make sure to click

  Read the article

• Wifi Drops Connections with WPA2-PSK

  - by graf_ignotiev

  I run a small computer lab made up of 10 computers of identical hardware and software (Dell Latitudes with Windows 7 x64 Enterprise) and I use a ZyWALL 2WG as a router/firewall. Nine of the computers connect to the router over wifi using WPA2-PSK encryption while the last one is connected by ethernet cable. I'm having a problem where any computer connected to the wi-fi occasionally drops off the network (it cannot be pinged and the client cannot ping the gateway). It only happens on the wifi side and only when the encryption is WPA2-PSK or WPA-PSK. I tried using another router with a different make and model and had no problems. Thinking it could be a software error, I reset the router to factory defaults and installed the newest firmware (V4.04(AQI.8) | 04/09/2010), but still have the problem. The 802.1X log gives the following error User logout because of user disassociation. with this note WPA2-PSK:00242c582ece:logout where 00242c582ece is the mac address of the device. At this point I'm out of things to try and leads to follow. It looks like this user had the same or similar problem, but none of those proposed solutions work for me.

  Read the article

• DIY NAS - links for Instructions

  - by Kaushik Gopal

  Good folk of SU, I'm planning to build a NAS (Network Access Storage). I'm planning to do it cheap (:read Old PC Config + Open source software). I was looking for good DIY links . Before you shoot this down as a Repost, I'm only looking for good links containing detailed instructions for setting up a NAS. I did a fair bit of searching and found these links (so please suggest others. While these links are great they delve more on the hardware side, i'm looking for more instructions in the software side). For the sake of the interwebs: Ubuntu: http://snarfquest.com/wiki/index.php/Setting_up_a_Home_NAS http://www.smallnetbuilder.com/content/view/27962/77/ http://jonpeck.blogspot.com/2006/11/how-to-configure-80-fileserver-in-45.html FreeNAS http://www.smallbusinesscomputing.com/webmaster/article.php/3719706 http://www.codeproject.com/KB/system/homemade_nas.aspxhttp://www.codeproject.com/KB/system/homemade_nas.aspx There was one at rubbervir.us that everyone points to, but apparently the site has gone down. A couple of other queries: Is Printer/Scanner sharing a possibility with NAS devices? Many talk of torrent support with NAS Devices, a little more light on this? Does this mean, an auto download of torrent through a feed into NAS, or just support for storing Torrent download files onto the NAS(don't see the difference between the latter and a normal file tranfer)

  Read the article

• Fedora-13 not detecting USB HDD enclosure (with HDD)

  - by Ramy

  I recently purchased this enclosure: http://www.amazon.com/Inland-2-5-Inc.../dp/B003SZ2Y12 and this HDD: http://www.amazon.com/Seagate-Barrac...3811667&sr=8-1 Now, I let my brother in law use the enclosure with his 160GB disk to back some stuff up. He then gave me that disk in my enclosure and I backed up my computer and my fiances computer. So...obviously, i had no problem mounting that disk. I plan on keeping this disk as my "natural disaster backup" (in case my apartment building burns down, i still have that disk with my stuff backed up). I want to use the 1.5T disk as my regular/more frequent backup device, but it doesn't seem to be mounting to my F-13 machine. I searched through this forum and found someone advising to run the following: # mount -t vfat /dev/sda1 /mnt this is the output i get when I run that: mount: /dev/sda1 already mounted or /mnt busy mount: according to mtab, /dev/sda1 is mounted on /boot Thing is, shouldn't this disk automatically mount just like the LAST disk in the same enclosure with the same USB cable and power supply? Any help would be greatly appreciated. THANKS!

  Read the article

• Trying to find the life expectancy of an unused flash card like SD

  - by wsams

  I read in the What's the life expectancy of an SD card? post SD cards are rated to hold data at something like 10 years sitting idle. I recall reading (not sure where) about re-energizing cards by occasionally inserting into a reader. Everything I read rates in read/write cycles and not physical decay. I'm wonder if buying a new sd card for every photo shoot would be beneficial if I could store the cards in a lock box? I was hoping for something much longer. Does anyone else agree with 10 years or maybe something more?

  Read the article

• Ubuntu: How to login without entering username and password

  - by torbengb

  I'm a newbie running Ubuntu 9.10. I have two users (wife and me), and each user's screensaver is set to lock so that on wakeup, we get to choose which user's desktop to go to. However, Ubuntu requires a password, so this is pretty tedious. I'd like to switch users without entering any password. I know about this trick that works for the boot login, but it doesn't deal with multiple users. Is it possible to set empty passwords for users in Ubuntu, or skip the password in other ways? (I'm expecting real Linux users to suggest that passwordless users must not get any rights and there be an admin user with a strong password. Yes, you're right. But that's not what this question is about. Thanks.)

  Read the article

• Parallel port blocking

  - by asalamon74

  I have a legacy Java program which handles a special card printer by sending binary data to the LPT1 port (no printer driver is involved, the Java program creates the binary stream). The program was working correctly with the client's old computer. The Java program sent all the bytes to the printer and after sending the last byte the program was not blocked. It took an other minute to finish the card printing, but the user was able to continue the work with the program. After changing the client's computer (but not the printer, or the Java program), the program does not finish the task till the card is ready, it is blocked until the last second. It seems to me that LPT1 has a different behavior now than was before. Is it possible to change this in Windows? I've checked BIOS for parallel port settings: The parallel port is set to EPP+ECP (but also tried the other two options: Bidirectional, Output only). Maybe some kind of parallel port buffer is too small? How can I increase it?

  Read the article

• Can't connect two PCs to a Network Switch at the same time (Windows 7)

  - by puk

  I have two computers connected to a network switch and every once in a while one of the computers will lose its internet connection. It's almost always the same computer every time. However, if I play around with the control panel, I can switch it, so that now the other computer is not connected. Restarting either of the computers does not help either. In Windows, the worlds-greatest-trouble-shooter tells me that a network cable is unplugged and that I should try plugging it in...Disabling and re-enabling my NIC does not fix this problem, neither does swapping cables around. When rebooting, the BIOS complains about how the Ethernet Cable is not plugged in. If it's in any way important, My set up at the office is like so: Modem - Routher - Network Switch 1 - Network Switch 2. I have tried turning off the energy saving option for my NIC, and I tried manually setting the link-speed to 100Mbps Full Duplex without any luck. Also, I have a Realtek PCIe GBE Family controller on both computers Does anyone have any idea why this is happening every 5-10 days? EDIT: I have also tried using a completely different Network Switch and the problem still persists as before.

  Read the article

• How to utilize 4TB HDD, which is showing up as 2.72TB

  - by mason

  I have two internal HDD's. They're both 4TB capacity. They're both formatted with the GPT partitioning scheme, and they're Basic Discs (not dynamic). I'm on Windows 8 64bit. I have UEFI, not BIOS. When I view the discs in Computer Management MMC with Disk Management, they show that each partition is formatted as NTFS and takes up the entire drive. And it shows that each drive has a capacity of 3725.90GB in the bottom section of Disk Management, but 2.794.39GB in the top section. When I view the discs in "My Computer"/"This PC" they only show up as 2.72TB, which matches the amount capacity I'm getting from some other 3TB HDD's I have. Why are they showing up as only 2.72GB? Will I be able to use the full 4TB capacity? Also of note, although I'm not sure it's relevant: I often get corrupted files on these two HDD's. None of my other HDD's give me corrupted files. Usually the problem is fixed by running chkdsk /f on the drives, but it's extremely annoying. In the picture below, it's the X: and Y: drives. Steps I've tried Flashed latest BIOS (MSI J.90 to K.30)

  Read the article

• Limit vsftp upload to a given set of file-names

  - by Chen Levy

  I need to configure an anonymous ftp with upload. Given this requirement I try to lock this server down to the bear minimum. One of the restrictions I wish to impose is to enable the upload of only a given set of file-names. I tried to disallow write permission to the upload folder, and put in it some empty files with write permission: /var/ftp/ [root.root] [drwxr-xr-x] |-- upload/ [root.root] [drwxr-xr-x] | |-- upfile1 [ftp.ftp] [--w-------] | `-- upfile2 [ftp.ftp] [--w-------] `-- download/ [root.root] [drwxr-xr-x] `-- ... But this approach didn't work because when I tried to upload upfile1, it tried to delete and create a new file in its' place, and there is no permissions for that. Is there a way to make this work, or perhaps use a different approach like abusing the deny_file option?

  Read the article

• Black screen on Ubuntu 12.04

  - by user1648371

  I've just upgraded to Ubuntu 12.04 and I'm experiencing some problems. The first thing I noticed is that when I click the Workspace switcher all I get is a black screen (I can guess where the different workspaces are located and clicked on them, not a practical solution though). In addition when I lock the screen or suspend the laptop (a Vaio VPCEB4M1E) I get a shifted screen (I see the right most vertical stripe on the left size of the monitor and nothing about all the rest, to put it clearly I can see the gear that allows me to turn the pc off, etc, but not much more..) when I go to the additional driver menu I see the "ATI/AMD proprietary FGLRX graphics driver" are installed and the post-release update version is available. I don't know if the problem is driver related, so before doing anything I'd like to get some suggestions from you guys. Thanks you!

  Read the article

• Juniper router dropping pings to external interface

  - by Alexander Garden

  My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

  Read the article

• EEE PC Keyboard malfunctioning - Ctrl key "sticks" after 10 seconds

  - by DWilliams

  I was given a EEE PC belonging to a friend of a friend to fix. The keyboard did not appear to work at all. I spent a while testing out various things, blowing the keyboard out, checking for damage, and so on. Nothing appeared to be physically wrong. At first I noticed that the keyboard appeared to work just fine for 10 seconds (on average, sometimes more sometimes less) after being powered on. It had been restored to the factory default xandros installation with no user set up, so I couldn't get in to mess with things since I couldn't type to make a user. I made an ubuntu live USB to boot it from, and managed to get the boot order changed to boot from USB in the ~10 seconds of working keyboard I had (I don't think I've ever had to rush around BIOS menus that quickly). After I got Ubuntu up on it, I played around a bit more and determined that apparently the ctrl key is stuck down (not literally, but it's on all the time). If I open gedit, pressing the "o" key brings the open dialog, "s" opens the save dialog, and all other behaviour you would expect to see if you were holding down the control key. The only exception that I noticed is the "9" and "0" keys. They function normally. Figuring that out I made a xandros user with a name/password consisting of 9's and 0's. I couldn't find any options in Xandros that could potentially be helpful. I'm not familiar with EEE PCs. Is it safe to assume that the keyboard is simply dead or could there be another problem? I don't want to purchase another keyboard for him if that isn't going to fix the problem. The netbook doesn't show any obvious signs of damage but the owner is a biker and very often has it with him on the road so it's been subjected to a good bit of vibration.

  Read the article

• Troubleshooting Mid 2007 iMac RAM upgrade

  - by MDT

  I am trying to install new RAM in my friends iMac, something I have done several times before. We unplugged the computer before performing the upgrade, used anti static wrist bands, and yes the memory is compatible and inserted correctly. The stock RAM was Hynix 1gb pc2-5300s-555-12 and the memory we are replacing it with is 2x2gb Centon CMP800SO2048.01. Now I know this model number suggests that the ram is 800MHz and the iMac is only 667MHz but it clearly states on the box that this RAM is PC2-5300 667MHz compatible. The problem is, that when I install the new RAM I get little response from the computer. I hear the hard drive and disk drive start to initialize, but then they just stop and the screen remains black. I have tried every variation of the new RAM and the old RAM in both slots and even tried the same RAM from my old iMac and I just can't get it to boot. Has anyone ever had a problem like this? Thank you in advance for any and all input on thus issue!

  Read the article

• What should I do to make sure that IIS does not recycle my application?

  - by AngryHacker

  I have a WCF service app hosted in IIS. On startup, it goes and fetches a really expensive (in terms of time and cpu) resource to use as local cache. Unfortunately, IIS seems to recycle the process on a fairly regular basis. So I am trying to change the settings on the Application Pool to make sure that IIS does not recycle the application. So far, I've change the following: Limit Interval under CPU from 5 to 0. Idle Time-out under Process Model from 20 to 0. Regular Time Interval under Recycling from 1740 to 0. Will this be enough? And I have specific questions about the items I changed: What specifically does Limit Interval setting under CPU mean? Does it mean that if a certain CPU usage is exceeded, the application pool will be recycled? What exactly does "recycled" mean? Is the application completely torn down and started up again? What is the difference between "Worker Process shutdown" and "Application Pool recycling"? The documentation for the Idle Time-out under Process Model talks about shutting down the worker process. While the docs for Regular Time Interval under Recycling talk about application pool recycling. I don't quite grok the difference between the two. I thought the w3wp.exe is the worker process which runs the application pool. Can someone explain the difference to the application between the two? The reason for having IIS7 and IIS7.5 tags is because the app will run in both and hope the answers are the same between the versions. Image for reference:

  Read the article

• Mysqldump causes "Too many connections"

  - by vbachev

  A scheduled backup using mysqldump on one of our databases is causing Too many connections. The database is of both InnoDB and MyISAM tables with size of around 500Mb. The Too many connections appears for about 2-3 minutes We understand that mysqldump locks the tables and causes all other queries and connections to pile up and jam the mysql server. We need frequent backups and we cannot afford server downtime or putting websites in maintenance mode while doing it. Our websites are global and traffic is high all the time so its hard to find a moment for backups. How can we avoid downtime during backups?Is there maybe a way to use mysqldump in way that it will not lock all tables at the same time?Is there an alternative to backing up with mysqldump?

  Read the article

< Previous Page | 438 439 440 441 442 443 444 445 446 447 448 449  | Next Page >