Search Results

Search found 18029 results on 722 pages for 'stripe size'.

Page 445/722 | < Previous Page | 441 442 443 444 445 446 447 448 449 450 451 452  | Next Page >

  • Tools/Tips to reduce the files/directories in C: which is SSD on Windows 7.

    - by prosseek
    I bought a SSD to install it as C: drive on Windows 7. As the SSD size is relatively small, I need to come up with an idea to reduce the files/directories in C:. What I found is as follows. Run WinDirStat to check how the C: is used. Remove the hibernate file (if you don't use it) powercfg –h off http://helpdeskgeek.com/windows-7/windows-7-delete-hibernation-file-hiberfil-sys/ Symbolic link files and directories to different drive. I'm not sure if this is safe way to go, I asked another post to ask about it. mklink /d e:\windows\installer c:\windows\installer Install software to E: directory, not C: directory. Create E:\Program Files What other tools or tips do you have?

    Read the article

  • Windows Server 2008 Static IP Address

    - by Gauls
    I have Win 2008 Server VM and want to set static IP address so that i can RDP into instead of using VM player (mouse gets out of focus as the size of the VM increases). Now while making the changes i see two TC/IPv6 and TC/IPv4 i try changing the IPaddress from obtain autimatically, but it always goes to "Unidentified Network". If i leave it to automatically obtain IP,i still cannot RDP into it. I have tired disabling TC/IPv6 from reistry. Any other suggestions? BTW the same setting works fine with WIN XP and i can RDP into all Win XP VM's Cheers Gauls

    Read the article

  • Using VLC to Unicast High Definition Webcam over local gigabit LAN with low/zero delay

    - by Robin Day
    We're setting up a webcam "window" between two offices in the same buildilng. The two PC's are connected to the same gigabit switch. We're using VLC to stream the webcam over HTTP using the following commands. vlc dshow:// :dshow-caching="0" :dshow-size="640x480" :sout=#transcode{vcodec=h264,vb=0,scale=0}:http{mux=ffmpeg{mux=flv},dst=:8080/} :no-sout-rtp-sap :no-sout-standard-sap :ttl=1 :sout-keep vlc http://192.168.0.1:8080 :http-caching="0" Even with the caching set to zero, the delay in the image is a good 2-3 seconds. The CPU usage of each pc is also maxed. I'm guessing it's the transcoding that's causing much of the delay. Can anyone give me some changes to these command lines that will reduce the transcoding power, or send the webcam over a different protocol, or anything that will reduce the delay of the cameras? Bandwidth is not an issue at all as the pc's can be connected to a dedicated switch/vlan if required.

    Read the article

  • Nginx, logrotate and empty files

    - by tzulberti
    I have a problem with nginx/logrotate. The problems is that nginx is logging access to 2 files (main and data). I have the following contrab setting: 0 * * * * /usr/sbin/logrotate -f /home/orwell/orwell-setup/bin/logrotate-nginx And the file "logrotate-nginx" has the following content: /tmp/data.log { rotate 90 daily missingok notifempty size 1 sharedscripts postrotate [ ! -f /tmp/nginx.pid ] || kill -USR1 `cat /tmp/nginx.pid` MORE THINGS endscript } /tmp/main.log { rotate 90 daily missingok notifempty size 1 sharedscripts postrotate [ ! -f /tmp/nginx.pid ] || kill -USR1 `cat /tmp/nginx.pid` MORE THINGS endscript } The work is done in the two files, but there is a problem that nginx stops logging into those files. Both files are created, but they are empty. Any ideas why nginx stop logging info to both files?

    Read the article

  • How to identify RAID (5 or 6) controllers that allow dynamic resize of the array

    - by David Pfeffer
    I'm building a server with a RAID5 array, based on a hardware controller. I want to be able to later add additional disks and have the array rebalance across all of the disks, enlarging the usable size. I also want to be able to later upgrade to bigger disks (one at a time, of course) and then expand the array to fill the entire drive. These features are available in Linux software raid (md). I've also heard they're available in some hardware controllers. Currently, I own the Adaptec RAID 3805 card and the 3ware 9650se card. I'd prefer to use the Adaptec if possible, but I can't find if either of these cards offer this feature. If they don't, are there other affordable (read as: sub-$600) RAID cards available that can accomplish this?

    Read the article

  • page rank 0 penalty

    - by mark
    I have a wordpress blog and a www-website on the same domain for about one year. Together it is about 170 pages. The page rank is still 0. I understand that page rank 0 is a penalty for duplicate content. The pages are indexed in google but still no page rank. In google webmaster tools there is no indication for any problem. I asked for reconsideration of both blog and website a month ago. Google accepted the reconsideration but it did not change anything. Other pages of similar size and similar audience earn PR 4-6. Is there something I can do in order to get a fair page rank? A coworker told me that it might be the case that a link farm is using the content and I can do nothing about it. Is there a reliable way to check for something like that? I do not like to give up so quickly is there a chance to fix this by for example moving to another domain?

    Read the article

  • How do I drag my widgets without dragging other widgets?

    - by Cypher
    I have a bunch of drag-able widgets on screen. When I am dragging one of the widgets around, if I drag the mouse over another widget, that widget then gets "snagged" and is also dragged around. While this is kind of a neat thing and I can think of a few game ideas based on that alone, that was not intended. :-P Background Info I have a Widget class that is the basis for my user interface controls. It has a bunch of properties that define it's size, position, image information, etc. It also defines some events, OnMouseOver, OnMouseOut, OnMouseClick, etc. All of the event handler functions are virtual, so that child objects can override them and make use of their implementation without duplicating code. Widgets are not aware of each other. They cannot tell each other, "Hey, I'm dragging so bugger off!" Source Code Here's where the widget gets updated (every frame): public virtual void Update( MouseComponent mouse, KeyboardComponent keyboard ) { // update position if the widget is being dragged if ( this.IsDragging ) { this.Left -= (int)( mouse.LastPosition.X - mouse.Position.X ); this.Top -= (int)( mouse.LastPosition.Y - mouse.Position.Y ); } ... // define and throw other events if ( !this.WasMouseOver && this.IsMouseOver && mouse.IsButtonDown( MouseButton.Left ) ) { this.IsMouseDown = true; this.MouseDown( mouse, new EventArgs() ); } ... // define and throw other events } And here's the OnMouseDown event where the IsDraggable property gets set: public virtual void OnMouseDown( object sender, EventArgs args ) { if ( this.IsDraggable ) { this.IsDragging = true; } } Problem Looking at the source code, it's obvious why this is happening. The OnMouseDown event gets fired whenever the mouse is hovered over the Widget and when the left mouse button is "down" (but not necessarily in that order!). That means that even if I hold the mouse down somewhere else on screen, and simply move it over anything that IsDraggable, it will "hook" onto the mouse and go for a ride. So, now that it's obvious that I'm Doing It Wrong™, how do I do this correctly?

    Read the article

  • How full is too full for mechanical hard drives?

    - by Sunny Molini
    I have heard many claim that it doesn't matter how full a drive is until it starts cutting into temp and virtual memory space. This doesn't make sense to me, given the nature of how the data is transacted on a hard drive. The inside of the platter presents less data per revolution than the outside of the drive does, by significant factors. The inside 40% of the radius of full size hard drive is used for the spindle, so only the outside 60% is used for data storage, but that still means that the inside track of a hard drive presents data 60% slower than the outside track. By my calculation, a Hard drive that is only 10% full should perform about 2.25 times faster than a hard drive that is 90% full, assuming that the flow is constrained by other factors. Am I wildly off base here? For all the drives I know, even the top speeds of the first 1% of the drive would be well within the bandwidth provided by a SATA 2 connection.

    Read the article

  • Wrong chrome full screen resolution with multiple displays

    - by Martin
    I am using Google Chrome on Windows 7 64bit with two displays. The displays have different resolutions and aspect-ratios. My problem is best visible when playing back full-screen videos from a flash player inside chrome (but it is not flash related). The maximum size is calculated from the primary displays' resolution, even when the relevant window is maximised on the second screen. The problem is also visible on websites that set the width to 100%. The 100% then apply to the primary display, even when the window is opened on the secondary display. Are there any known solutions to this problem? I am observing it since many Chrome versions, do not know if it has been ever correct.

    Read the article

  • Why can't gif images copy at a reasonable speed on this dell laptop with XP?

    - by alt234
    I've got this somewhat old Dell Latitude D810. Strangest thing... If I try to copy anything that has gif files in it the gif files take forever. Like a few minutes per gif regardless of size. Everything else copies fine. I notice this when copying files off our network, copying off multiple external drives, and even when files are copying during an installation process. I'm on Windows XP Pro service pack 3. I've never seen anything like this before. Anyone else?

    Read the article

  • Ubuntu Tools for recovering data from damaged USB Flash Drive ~ 10 Gb

    - by PREDA LUCIAN
    I have technical issues with my USB Flash Drive - JetFlash®V15 (TS16GJFV15) It's very critical situation because I can not see the data from it and I should get a way to recover them ASAP. So, in general, I have connected Non-stop that USB Flash Disk at my laptop. Was appear Power surges and when I was coming back, I saw that problem with it. Details regarding JetFlash®V15 (in present): - when I connect it on USP slot, the led is working intermittent and later on remain with constant light. - if I inspect the computer drivers, I found "Generic USB Flash Disk" (when the stick it's connected). - if I inspect "Properties", I can see next details: --- Type: unknown (application/octet-stream) --- Size: unknown --- Volume: unknown --- Accessed: unknown --- Modified: unknown I inspected that stick on 2 different computers (as well in different different USB Ports) and was the same problem, I can not see the content. I was checking with Windows 7 and Ubuntu 10.04 OS, but without success. With both OS was working before this issue. I'll appreciate an answer which will solve the problem, not an answer which will certify the problem. What I have to do, to recover the information form it (nearly 10 Gb)? I'm looking forward to be guided from a technical expert.

    Read the article

  • Programatically Determine Exchange Attachment Limit

    - by Jeff Ballard
    Is there any way to query the exchange server to determine the maximum attachment file size? I'd be doing this in ASP.NET/C#. I'd like to be able to validate the file they want to attach is not over the limit before the user attempts to send the file to the server as opposed to having the server send back an exception when it attempts to attach the file and it discovers the file is too large. I've also posted this question about this on stackoverflow.com as well - I figured a sysadmin for Exchange may have an answer as well as a developer. Hopefully I do not incur the wrath of the stackexchange gods.

    Read the article

  • PDF export printing in Internet Explorer [closed]

    - by user619804
    protected static byte[] exportReportToPdf(JasperPrint jasperPrint) throws JRException { JRPdfExporter exporter = new JRPdfExporter(); ByteArrayOutputStream baos = new ByteArrayOutputStream(); exporter.setParameter(JRExporterParameter.JASPER_PRINT, jasperPrint); exporter.setParameter(JRExporterParameter.OUTPUT_STREAM, baos); exporter.setParameter(JRPdfExporterParameter.PDF_JAVASCRIPT, "this.print({bUI: true,bSilent: false,bShrinkToFit: true});"); exporter.exportReport(); return baos.toByteArray(); } We are using code like this to export a PDF document from a Jasper application. The line exporter.setParameter(JRPdfExporterParameter.PDF_JAVASCRIPT, "this.print({bUI: true,bSilent: false,bShrinkToFit: true});"); adds JavaScript to send the PDF document directly to the printer. The expected behavior is that a print dialog will come up with a preview of the PDF document. This works fine most of the time - except I am having problems about one out of every 5-6 times in Internet Explorer 8 and Firefox. What happens is - the print preview dialog with the PDF document does not appear or it appears with a blank document in the preview window. -I've tried a number of different JavaScripts (different params to this.print() via exporter.setParameter -I've tried setting different response headers such as response.setContentType("application/pdf"); response.setHeader("Content-disposition","inline; filename=\"" + reportName + "\""); response.setContentLength(baos.size()); these did not seem to help This seems to be an IE and FF issue. Has anyone ever dealt with this problem? I need to get it to work across all browsers 100% of the time. Perhaps a different approach to accomplish the goal of sending the PDF document export directly to the printer? or a third party library that will work across browsers?

    Read the article

  • Desktop goes blurry / granulated

    - by Bonfire
    After few minutes using, desktop and fonts in unity-menu goes blurry. See screenshot.! In all applications (browser etc.) graphics seem to be allright. After rebooting problem disappears for few minutes. Changing the wallpaper also makes the desktop clear (for a while) but fonts are still blurry. I have ubuntu 12.04 and windows xp dualbooted. lspci: 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) 00:02.1 Display controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) lshw -c video: *-display:0 description: VGA compatible controller product: 82945G/GZ Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:16 memory:d0100000-d017ffff ioport:30c0(size=8) memory:c0000000-cfffffff memory:d0180000-d01bffff *-display:1 UNCLAIMED description: Display controller product: 82945G/GZ Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 02 width: 32 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:40000000-4007ffff Have you got any ideas to get this solved? Thank you very much! Bonfire

    Read the article

  • On Windows 7, how can I tell if a recording is multi-channel without third party tools? [migrated]

    - by engineerchuan
    A customer has an audio that is confidential and can't send it to me. He also would not like to install other tools. He has a basic Windows 7 install. Is there any way to tell whether the recording is one channel or two channel? Normally, I would just get the audio and soxi it. Or, I would tell him to install Audacity or equivalent sound editor and open it up. I also thought that if you right clicked and looked at the size, bit rate, and length, you could get number of channels but bit rate already factors in number of channels. Sorry I'm not giving you a lot to work with.

    Read the article

  • Windows 8.1 - Why are there multiple recovery partitions in the system?

    - by Abhiram
    DISKPART> list partition Partition ### Type Size Offset ------------- ---------------- ------- ------- Partition 1 System 500 MB 1024 KB Partition 2 OEM 40 MB 501 MB Partition 3 Reserved 128 MB 541 MB Partition 4 Recovery 490 MB 669 MB Partition 5 Primary 920 GB 1159 MB Partition 6 Recovery 350 MB 921 GB Partition 7 Recovery 9 GB 921 GB Above is the list of partitions on my system that I recently upgraded to Windows 8.1. Why are there multiple recovery partitions (4,6,7)? Shouldn't there be just one recovery partition? And what is the Reserved partition (#3) for?

    Read the article

  • Serializing network messages

    - by mtsvetkov
    I am writing a network wrapper around boost::asio and was wondering what is a good and simple way to serialize my messages. I have a message factory which can take care of dispatching the data to the correct builder, but I want to know if there are any established solutions for getting the binary data on the sender side and consequently passing the data for deserialization on the receiver end. Some options I've explored are: passing a pointer to a char[] to the serialize/deserialize functions (for serialize to write to, and deserialize to read from), but it's difficult to enforce buffer size this way; building on that, I decided to have the serialize function return a boost::asio::mutable_buffer, however ownership of the memory gets blurred between multiple classes, as the network wrapper needs to clean up the memory allocated by the message builder. I have also seen solutions involving streambuf's and stringstream's, but manipulating binary data in terms of its string representation is something I want to avoid. Is there some sort of binary stream I can use instead? What I am looking for is a solution (preferrably using boost libs) that lets the message builder dictate the amount of memory allocated during serialization and what that would look like in terms of passing the data around between the wrapper and message factory/message builders. PS. Messages contain almost exclusively built-in types and PODs and form a shallow but wide hierarchy for the sake of going through a factory. Note: a link to examples of using boost::serialization for something like this would be appreciated as I'm having difficulties figuring out the relation between it and buffers.

    Read the article

  • Ubuntu One, compressed files

    - by user8179
    I have uploaded some files to my Ubuntu One account and it seems to work great most of the time. I usually upload them directly from Nautilus by right clicking the folder, using the ”Synchronize this folder” option, and then I make sure that the file I want to upload is published. Then I usually test the whole thing by trying to download it. I right click the file again to get its URL and I paste it into my Web browser. This usually works fine. But yesterday I uploaded two compressed files – ”.tar.bz2”. When I tried to open them after downloading them with my Web browser (Opera), it failed. I found that the file was bigger than the original file (2358 B instead af 2335 B – 15 B added at the beginning of the file and 8 B added to the end), and someone at the Opera channel (IRC) at OperaNet (Europe) figured out that the reason for this is that the server compress the file again, ”without telling Opera”. So to be able to extract the file I need to add ”.gz” to the file name and then extract it twice. If I downloaded it with Firefox however, I didn't need to do that, so maybe Firefox figured this out somehow in a way that Opera does not. Someone also tried to download the file with wget and some other browser and he also got the same result as I did with Opera, that is the file is compressed a second time by the server. I guess ”the server” is the Ubuntu One server, right? So why is this? Could it be done better somehow? Or did I do something wrong when uploading the files? It also seems like this extra compressing thing does not always happen, because when I tried again a few minutes ago, the file came down with its right size (2335 B), without an extra compression. But the other file (114 MiB) was still compressed twice.

    Read the article

  • Issue with image lightbox and enlargement / Jquery Mobile

    - by Matt
    I'm working on a redesign of my weather website using Jquery Mobile. I have it set up so that you drill down through a series of content containers to get to the weather info (each group of info opens in a dialog display). Everything's worked well, but I've run into an issue with my images. I have them sized so that they fit a mobile device's screen nicely, but because of that, when you look at them in a desktop browser, you can't really make out what the image is. I've tried several image lightbox / enlargement solutions, but for some reason, none of them have worked. Either nothing happens or the images open in a new window. I thought that this might be caused by Jquery Mobile somehow overwriting the scripts and css of the lightbox / enlargements I've tried. I'm not completely sure though that this is the case, and if it is, how I can get around it to be able to enlarge the images to their original size, preferably onclick. Here is a working (for the most part - still some kinks to work out) example. If you look under the "Tropical" section at the "Satellite-Derived Products", you'll see what I mean. http://www.suncoaststormwatch.com/Beta/Index.html

    Read the article

  • file copy error from system to cifs mount

    - by dwpriest
    When coping a file greater than 64kB from an Ubuntu server to a CIFS mounted windows share, most of the data is copied, but it seems the last chunk doesn't get copied. The size doesn't match, and the md5 check sums don't match. I have plenty of file space, but then I use cp, I get the following... cp: closing `cloudBackup/asdf.txt': No space left on device Using rsync, I get the following... rsync: close failed on "/home/fluffy/cloudBackup/.asdf.txt.qrBWe6": No space left on device (28) rsync error: error in file IO (code 11) at receiver.c(752) [receiver=3.0.8] rsync: connection unexpectedly closed (29 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(601) [sender=3.0.8] I have full read/write permissions on the mounted share. I can copy via SSH just fine. Any ideas? Thank you

    Read the article

  • 1080p Screen resolution problem after 10.04 to 12.04 update

    - by Ale
    I have a Samsung LCD 40" with a NVidia GeForce 6150SE nForce 430 Card. I recently upgraded from 10.04 to 12.04 and the best resolution I can get is 1360x768. I've tried the propietary drivers available on the repository kmod:nvidia_current kmod:nvidia_173_updates kmod:nvidia_current_updates kmod:nvidia_96 kmod:nvidia_96_updates kmod:nvidia_173 I've also downloaded latest from NVidia's Web, version: 295.40. But still no luck. With Nouveau driver, I can only get 1024x768. I know there is no problem with my hardware (video card, cable and monitor), I was using it perfectly on 10.04. Can anybody suggest something else I could try, to get my 1920x1080 resolution back? Thanks in advance. Here are some more information, that I got reading other similar posts on askubuntu. $ lspci | grep VGA 00:0d.0 VGA compatible controller: NVIDIA Corporation C61 [GeForce 6150SE nForce 430] (rev a2) $ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 240, current 1360 x 768, maximum 1360 x 768 default connected 1360x768 0 0 0mm x 0mm 1360x768 50.0 52.0* 1024x768 51.0 800x600 53.0 54.0 55.0 680x384 56.0 57.0 640x480 58.0 576x432 59.0 512x384 60.0 400x300 61.0 62.0 63.0 320x240 64.0

    Read the article

  • How to force 640*480@60Hz screen resolution on xubuntu 12.04

    - by c2h2
    It seems xubuntu won't be able to correctly set resolution at 640*480@60Hz at its Display settings. And I am unable to correctly my super small 6.4 inch Mitsubishi VGA panel via VGA cable. I have tried to hack both X11 conf /etc/X11/Xorg.conf and xfce4 conf, but all the document I can find is outdated. and conf files are changed into other location. Can someone give me a hand and I'll mark correct for other people to use? Thanks! EDIT: The board is an Intel Atom D2700, gpu is SGX545. I tried to use xrandr --output default --mode 640*480 It seems works fine, but refresh rate is 75Hz, but the screen only suports 60Hz So I used xrandr --output default --mode 640*480 --rate 60 but it give error: xrandr: Failed to get size of gamma for output default Can anyone pointing any directions?

    Read the article

  • recommendations for a lightweight linux distribution for a test server

    - by Jack
    I'm planning on setting up a test server to experiment with some application servers (tomcat/jboss/...) and with some portals. Now the machine I've set aside for this is lightweight CPU/GPU wise(Atom D510, 4 gigabyte ram, 500 GiB hdd, onboard GPU). But it should suffice for most things, I'm more interested in the stability of JBoss/Tomcat for my purposes than the stability. However I'm having a bit of trouble picking an appropriate distribution size/performance/setup time wise/security wise since it seems I can't sneeze without another distribution popping up. I've been thinking about going for Fedora since I've read that that distribution has been optimized for Atom, but I'm not really familiar with it. My experience with Linux has mostly been limited to Ubuntu and some tinkering with puppylinux. I'm not afraid to get my hands dirty using the command line. I'm not planning on starting a discussion per se, mostly the pros/cons that people have encountered with some distributions

    Read the article

  • How to suggest changes as a recently-hired employee ?

    - by ereOn
    Hi, I was recently hired in a big company (thousands of people, to give an idea of the size). They said they hired me because of my rigor and because I was, despite my youngness (i'm 25), experienced as a C/C++ programer. Now that I'm in, I can see that the whole system is old and often uses obsolete technologies. There is no naming convention (files, functions, variables, ...), they don't use Version Control, don't use exceptions or polymorphism and it seems like almost everybody lost his passion (some of them are only 30 years old). I'd like to suggest somes changes but i don't want to be "the new guy that wants to change everything just because he doesn't want to fit in". I tried to "fit in", but actually, It takes me one week to do what I would do in one afternoon, just because of the poor tools we're forced to use. A lot my collegues never look at the new "things" and techniques that people use nowadays. It's like they just given up. The situation is really frustrating. Have you ever been in a similar situation and, if so, what advices would you give me ? Is there a subtle way of changing things without becoming the black sheep here ? Or should I just give up my passion and energy as well ? Thank you. Updates Just in case (if anyone cares): following your precious advices I was able to suggest changes and am now in charge of the team that must create and deploy Subversion :D Thanks to all of you !

    Read the article

  • Tail-recursive implementation of take-while

    - by Giorgio
    I am trying to write a tail-recursive implementation of the function take-while in Scheme (but this exercise can be done in another language as well). My first attempt was (define (take-while p xs) (if (or (null? xs) (not (p (car xs)))) '() (cons (car xs) (take-while p (cdr xs))))) which works correctly but is not tail-recursive. My next attempt was (define (take-while-tr p xs) (let loop ((acc '()) (ys xs)) (if (or (null? ys) (not (p (car ys)))) (reverse acc) (loop (cons (car ys) acc) (cdr ys))))) which is tail recursive but needs a call to reverse as a last step in order to return the result list in the proper order. I cannot come up with a solution that is tail-recursive, does not use reverse, only uses lists as data structure (using a functional data structure like a Haskell's sequence which allows to append elements is not an option), has complexity linear in the size of the prefix, or at least does not have quadratic complexity (thanks to delnan for pointing this out). Is there an alternative solution satisfying all the properties above? My intuition tells me that it is impossible to accumulate the prefix of a list in a tail-recursive fashion while maintaining the original order between the elements (i.e. without the need of using reverse to adjust the result) but I am not able to prove this. Note The solution using reverse satisfies conditions 1, 3, 4.

    Read the article

< Previous Page | 441 442 443 444 445 446 447 448 449 450 451 452  | Next Page >