Search Results

Search found 29354 results on 1175 pages for 'scala 2 10'.

Page 446/1175 | < Previous Page | 442 443 444 445 446 447 448 449 450 451 452 453  | Next Page >

• pptp server 2003 hands out gateway from nic not dhcp server

  - by Pete

  I have created a pptp RRAS server for a handful of clients to connect to. I would like them to use the servers default gateway (.1) for internet access. They are able to successfully connect (& see LAN) but it then cuts them off the internet. I understand that all internet traffic would be routed through the pptp server but that's ok since I have enough pipe. The problem seems to be that: the clients gateway shows as their assigned RAS ip. The clients assigned DNS settings seem to be what is set to the servers nic not what I have specified in dhcp (which is the same server). DHCP relay agent properties points to the nic DHCP is running on (192.168.100.163). .1 is gateway in nic hw properties & dhcp. I have different dns secondary & third entries on my nic properties than what dhcp is configured for. The problem is that I have a 10.10.1.x network that people can not see if they uncheck the gateway option but, they are then unable to see our other hosted sites on the internet.

  Read the article

• Network topology for both direct and routed traffic between two nodes

  - by IndigoFire

  Despite it's small size, this is the most difficult network design problem I've faced. There are three nodes in this network: PC running Windows XP with an internal WiFi adapter.Base station with both WiFi and a Wireless Modem (WiModem)Mobile device with both WiFi and WiModem The modem is a low-bandwidth but high-reliability connection. We'd like to use WiFi for high-bandwidth stuff like file transfers when the mobile is nearby, and the modem for control information. Here's the tricky part: we'd like the wifi traffic to go directly from the mobile to the PC, as rebroadcasting packets on the same WiFi channel takes up double the bandwidth. We can do that with a manual configuration by giving the both the PC and the base station two IP addresses for their WiFi interfaces: one on a subnet shared with the mobile, and one on their own subnet. The routes on the PC are set up so that any traffic going to the mobile via WiModem goes through the secondary IP address so that return traffic from the mobile also goes through the WiModem. Here's what that looks like: PC WiFi 1: 192.168.2.10/24 WiFi 2: 192.168.3.10/24 Default route: 192.168.2.1 Base Station WiFi 1: 192.168.2.1/24 WiFi 2: 192.168.3.1/24 WiModem: 192.168.4.1/24 Mobile WiFi: 192.168.3.20/24 WiModem: 192.168.4.20/24 We'd like to move to having the base station automatically configure the mobile and PC, as the manual setup is problematic when you start having multiple mobiles and PCs. This means that the PC can only have 1 IP address and needs to be treated as being pretty simple. Is it possible to have a setup driven by DHCP on the base station that is efficient with bandwidth?

  Read the article

• Trobleshooting extremely slow opening times in Win7 for documents on Win2k8 server

  - by Mazupan

  Hello. It's hard even to describe my problem. It seems there's only problem with extreme slow openings (up to 10 minutes) on Windows 7 (on XP things works fine) for files that are stored on Windows Server 2008. And now what I discovered up till now. If I open (some files, not all, not allways) .doc and .xls files with doubleclicking it takes up to 10 minutes to finaly open the file. In that time, file seems to be locked for all other users. If I cancel opening, file remains locked for some time. Owner on that files is the one who last wrote changes in them. If I change the owner to larger group, which I am member of file gets opened super fast. When opened file can be saved normaly and fast. That file reopens fast. One other user reports that there is only problem when opening the files for the first time in a day. When he openes first file he has no problems with other files at all (or so he says). He also states that when accessing files from home via VPN he has no such problems with files. And now: anybody has a clue where to start looking? I suppose that is misconfiguration problem. But where? File system? Permissions? DFS? VMWare network config? My setup is as follows: Physical server: HP Prolian ML350 G6 Virtual host: VMWare ESXi 4 Guest: Windows Server 2008 Standard Files are accessed via DFS shares. Please help me. Thanks. Mazupan

  Read the article

• 1080p monitor: connected through VGA - perfect, HDMI - awful

  - by develroot

  When I connect my 23" monitor (1920x1080) to my pc through HDMI, I encourage some problems. It's not full screen That's it. There are ~1cm black borders on right and left side and ~0,5cm black borders on the top and the bottom of the monitor. That's pretty frustrating. I tried adjusting overscan, but I can't mannualy type the % of overscan that I need. I can only select between ex. 8 and 10% in AMD Vision Engine Control center, but what I need is 9%. Next, even if i select 10% and the image fits all the corners, but after log off all the settings are lost and I have to do it again and again. Text, images, everything looks blurry That surprised me a lot. Should'nt HDMI quality be better than VGA's one? When connected through HDMI, the text isn't readable. It's like a very low refresh rate, although i'm running at 60Hz. Also the text has something like little shadows, very very annoying. Are there any tips to get the same quality as with VGA, with HDMI ? (running on integrated ATI Radeon HD4200, which, appearently, is the best card I have ever seen in terms of integrated ones)

  Read the article

• SSD suddenly full

  - by Daniel

  Today the hard drive of our server was suddenly full. The disk usage always stayed around 50 % in the weeks and months before (old data is regularly expunged from the server). I deleted 10 GB of files in /tmp, which strangely freed 51 GB. Here is what I did: root@***:~# df -h Dateisystem Size Used Avail Use% Eingehängt auf /dev/sda3 139G 137G 0 100% / tmpfs 3,9G 0 3,9G 0% /lib/init/rw udev 3,9G 116K 3,9G 1% /dev tmpfs 3,9G 0 3,9G 0% /dev/shm /dev/sda1 985M 25M 910M 3% /boot root@***:/var# du -hs * 3,3M backups 438M cache 9,4G lib 4,0K local 12K lock 76M log 24K mail 4,0K opt 88K run 184K spool 10G tmp 12K www root@***:/var/tmp# find -type f -print0 | xargs -0 rm root@***:/var/tmp# df -h Dateisystem Size Used Avail Use% Eingehängt auf /dev/sda3 139G 81G 51G 62% / tmpfs 3,9G 0 3,9G 0% /lib/init/rw udev 3,9G 116K 3,9G 1% /dev tmpfs 3,9G 0 3,9G 0% /dev/shm /dev/sda1 985M 25M 910M 3% /boot Any explanation as to why deleting 10 GB in /tmp gave me back 51 GB on the disk? Could this point to an SSD failure? Are there any tools for Debian to test SSD health? I already have checked syslog. The first entry relating to this incidient is a mysql message: 1:22:02 [ERROR] /usr/sbin/mysqld: Disk is full writing... So I have absolutely no idea what caused this.

  Read the article

• Terratec Cinergy Hybrid T USB XS is not recognized anymore on Mac OS X

  - by Gabble

  I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. It is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. Reset the PRAM. Nope. Checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. I need to say that: a) The device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause). b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me. Thanks in advance for any help you will offer!

  Read the article

• Server 2003 and SSL Certificates

  - by Keith Stokes

  I have a Windows 2000 domain with dozens of Windows 2000 servers and a few 2003 servers. Each server runs a custom app talking to a 3rd party utilizing self-signed certificates. To help troubleshooting we've created a custom test app. The 2000 servers are able to talk within seconds. The 2003 servers take anywhere from 10-30 seconds using a domain account and much less, usually under 5 seconds using a local account. The only exception to the local account performance is a new account, which is slow initially then faster. If you leave the test app open and reconnect repeatedly it talks in seconds. If you leave it open for sometime between 1 and 2 hours, it reverts back to the previous 10 seconds, so obviously something is caching. Installing the destination certificates in the local 2003 server store makes no difference. I've installed the certificates in AD and that apparently makes domain accounts work in 9-12 seconds, vs 30 seconds that was regular before. Manually clearing the certificate store on the 2003 server makes no difference. I'm at a loss as to where the certs might be cached and if I'm using some sort of domain certificate store that's hiding from me.

  Read the article

• BIND: forward 1st level zone

  - by raven

  First of all: sorry for the language, English is not my primary language. I have star-like DNS structure with many filials (more that 2): ^ | v filialNS_1.filial_1.city.local <---- ns.main.city.local <---- filialNS_2.filial_2.city.local ^ | v ns.mail.city.local is slave of all filials zones filialNS_1 is master of filial_1.city.local filialNS_2 is master of filial_2.city.local filialNS_N is master of filial_N.city.local I want to: serve DNS queries for xxx.filial_N.city.local with filialNS_N.filial_N.city.local forward all queries for xxx.xxx.xxx.local from filialNS_N to ns.main.city.local forward other queries to our provider's DNS on filial (or google-public-dns or anything else) FILIAL CONFIG named.conf zone "filial_1.city.local" { type master; file "/etc/namedb/dynamic/filial_1.city.local"; allow-update { key DHCP_UPDATER; }; allow-transfer { <ns.main.city.local IP address> }; }; zone "2.76.10.in-addr.arpa" { type master; file "/etc/namedb/dynamic/2.76.10.in-addr.arpa"; allow-update { key DHCP_UPDATER; }; allow-transfer { <ns.main.city.local IP address> }; }; zone "local." { type forward; forward only; forwarders { <ns.main.city.local IP address> }; }; nslookup server.filial_1.city.local - works fine nslookup server.main.city.local Server: 127.0.0.1 Address: 127.0.0.1#53 ** server can't find server.main.city.local: NXDOMAIN Where am I going wrong?

  Read the article

• quickly close all word and excel

  - by dyenatha

  Suppose I open 10 Word files and 10 Excel files and make no changes, how do I quickly taskkill all at once? Because I must repeat several attempts to replicate race, I'm hoping for a command-line solution. I'm willing to try PowerShell and cygwin (1.5) if necessary. The OS is Windows XP SP3 with current patches (still IE7). I tried "taskkill /pid 1 /pid 2 /t" where 1 is PID of EXCEL.EXE and 2 is PID of WINWORD.EXE, but it closed only 1 window of each program. I'm trying to replicate a race where an add-in for Microsoft Office 2007 fails to exclusive-lock one of its own files, which caused the 2nd Office program to stop exiting with a warning: System.IO.IOException: The process cannot access the file 'C:\Documents and Settings\me\Application Data\ExpensiveProduct\Add-InForMicrosoftOffice\4.2\egcred' because it is being used by another process. at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath) at System.IO.FileStream.Init(String path, FileMode mode, FileAccess access, Int32 rights, Boolean useRights, FileShare share, Int32 bufferSize, FileOptions options, SECURITY_ATTRIBUTES secAttrs, String msgPath, Boolean bFromProxy) at System.IO.FileStream..ctor(String path, FileMode mode, FileAccess access, FileShare share, Int32 bufferSize, FileOptions options) at System.IO.StreamWriter.CreateFile(String path, Boolean append) at System.IO.StreamWriter..ctor(String path, Boolean append, Encoding encoding, Int32 bufferSize) at System.IO.StreamWriter..ctor(String path, Boolean append, Encoding encoding) at System.IO.File.WriteAllText(String path, String contents, Encoding encoding) at ExpensiveProduct.EG.DataAccess.Credentials.CredentialManager.SaveUserTable() at ExpensiveProduct.OfficeAddin.OfficeAddinBase.Dispose(Boolean disposing) at ExpensiveProduct.OfficeAddin.WordAddin.Dispose(Boolean disposing) at ExpensiveProduct.OfficeAddin.OfficeAddinBase.OnHostShutdown() at ExpensiveProduct.OfficeAddin.OfficeAddinBase.Unload(ext_DisconnectMode mode)

  Read the article

• Ubuntu 8.04 wont reboot from script

  - by Littlejon

  I have a script that is run to backup a server via Rsync, after that script is run I want the server to reboot. My script is run as root from the Crontab at 3am in the morning. #!/bin/bash HOST="email" RSYNC_OPTS="-a -v -v --progress --stats --delete" RSYNC_DEST="10.0.0.10::$HOST" BACKUP_LIST="/etc /home /root" TIMESTAMP="/timestamp-bkup-start.chk" TIMESTAMP2="/timestamp-bkup-stop.chk" touch $TIMESTAMP rsync $RSYNC_OPTS $TIMESTAMP $RSYNC_DEST for BACKUP_ITEM in $BACKUP_LIST; do rsync $RSYNC_OPTS $BACKUP_ITEM $RSYNC_DEST done /etc/init.d/zimbra stop sleep 60s rsync $RSYNC_OPTS /opt $RSYNC_DEST touch $TIMESTAMP2 rsync $RSYNC_OPTS $TIMESTAMP2 $RSYNC_DEST echo `date +%Y%m%d%H%M` >> /var/log/reset reboot # $# shows number of args passed # $1 to access first variable #if [ $# -eq 1 ]; then # if [ $1 = "withreboot" ]; then # echo "rebooting..."; # echo `date +%Y%m%d%H%M` >> /var/log/reset # /sbin/reboot # fi #fi I have tried using init 6 rather then reboot. I have tried /sbin/reboot. I also have another basic script that just echos to the reset log and runs reboot without issue. It is just with the script above the server wont restart. If anyone has any theories that would be great as I have run out of idea. Thanks, Jon

  Read the article

• ldapsearch against Active Directory fails

  - by Guacamole

  I am using ldapsearch from OpenLDAP tools to search our corporate Active Directory for my email and phone number. This query is a test to ensure that I can authenticate against the domain so I can set up a linux wiki with NTLM authentication. My theory is that if I can successfully query the AD for information, then I am a step closer to getting my wiki to authenticate against AD (I have instructions to set up moin wiki under ActiveDirectory). The problem is that I can't seem to get the ldapsearch query right. I have seen many tutorials on the net that indicate that -D should be something like -D "Americas\John_Marsharll"; however, I keep getting ldap_bind: Invalid credentials (49) error messages when I use Americas\John_Marshall. The only time I get sensical results is when I query with the parameters below. However, even then, I can't figure out how to get email and phone number. [John_Marsharll@WN7-BG3YSM1 ~]$ ldapsearch -x -h 10.1.1.1 \ -b "cn=Users,dc=Americas" mail telephonenumber -D "cn=John_Marshall,dc=Americas" # extended LDIF # # LDAPv3 # base <cn=Users,dc=Americas> with scope subtree # filter: (objectclass=*) # requesting: mail telephonenumber -D cn=John_Marshall,dc=Americas # # search result search: 2 result: 32 No such object # numResponses: 1 [John_Marshall@WN7-BG3YSM1 ~]$ Can someone give me pointers on what I'm doing wrong with the ldapsearch query above? Our AD ldap server is 10.1.1.1 and the AD domain is "Americas".

  Read the article

• Unable to Align Layers in Photoshop Properly with CS2

  - by Jonathan Sampson

  Cannot Align Semi-Transparent Items? Windows Vista, Photoshop CS2. Steps to repeat: Create new document Fill a circle on a new layer Drop opacity of filled circle to 10% Create new empty layer below circle layer Merge empty layer with filled circle layer Select entire canvas Attempt to align layers to selectionlayer > align layers to selection > vertical centers I get the following error: Could not complete the Vertical Centers command because there are no layers to be moved. Clearly this is not true, as I'm selecting the layer with the semi-translucent ball on it. Now, if you had tried this same command prior to step 5 (when the layer was at 10% opacity) it would have worked. Is there some way around this problem? I need to move layers around that begin as transparent items, with a layer opacity at 100% where 100% of the layers opacity results in showing objects that are themselves not-very opaque. I've confirmed on another machine that this problem doesn't exist in CS3. I may exist in earlier copies of Photoshop, but I only have access to CS2 (has the problem) and CS3 (does not have the problem).

  Read the article

• what type of laptop do I need to run a amd64 or i386 VM?

  - by Frank Schwieterman

  I was running an amd64 build of Ubuntu on a VM on a Windows host which was also amd64. Later I found I could not run the same amd64 iso on my laptop, which is intel without hyper-V. I was confused I thought chipset mattered, but maybe it does not. When buying a PC or Apple, is there anything to check about the chipset to make sure it can run different types of VMs? In my case, I was trying to run ubuntu on a Thinkpad T520. Per answer below, I did need to enable some bios settings. I'm still having some issues. Running ubuntu on virtual box, when I try to use ubuntu-12.10-server-amd64.iso for the CD/DVD device to start a new VM, virtualbox complains "Failed to open the CD/DVD image . Could not get the storage format of the medium (VERR_NOT_SUPPORTED). When I try to use ubuntu-12.10-server-i386.iso the ISO is accepted, but then the VM complains "FATAL: No bootable medium found! System halted." I had been using an amd64 iso on my home PC which is amd64 and it works fine, which is why I suspected CPU mismatch was the problem at first. But it seems like I'm having issues, and maybe this superuser thread can be used to verify the cpu is irrelevant in this case.

  Read the article

• Offloading backups to secondary network

  - by user1467163

  I'm trying to solve a problem- Currently, we are constantly backing up and have no budget for additional servers. Our production network is still a 10/100 and handles voip, SQL plus our backup traffic, and I'd like to offload the backup traffic onto a secondary network- all of our servers have secondary NIC's that are not in use, and all support gigabit (Our switching hardware does not- a topic for another day). I'd like to move my backups off the production network, but I am having a hard time getting the computers to communicate. I am using a Netgear GS724T switch for the backup network- Chosen for cost and because I have used them extensively on networks saturated with ghosting traffic, so I know it's up to the task. I have defined a VLAN, with ports that are not members of any other VLAN. All traffic is untagged on the VLAN. I have set the servers with 192.168.1.10 and 192.168.1.11 addresses, 255.255.255.0 netmask and I have tried a blank GW, using the local IP of the server 192.168.1.whatever address, and I have tried using the switch's production-side IP as the GW. The machines cannot find each other. DNS addresses are blank because I am going purely by IP for now... Any ideas how to get these machines to talk? they are Windows machines, running Server 2008R2 and 2003R2. Thanks!

  Read the article

• How to tell nginx to honor backend's cache?

  - by ChocoDeveloper

  I'm using php-fpm with nginx as http server (I don't know much about reverse proxies, I just installed it and didn't touch anything), without Apache nor Varnish. I need nginx to understand and honor the http headers I send. I tried with this config (taken from the docs) but didn't work: /etc/nginx/nginx.conf: fastcgi_cache_path /var/lib/nginx/cache levels=1:2 keys_zone=website:10m inactive=10m; fastcgi_cache_key "$scheme$request_method$host$request_uri"; /etc/nginx/sites-available/website: server { fastcgi_cache website; #fastcgi_cache_valid 200 302 1h; #fastcgi_cache_valid 301 1d; #fastcgi_cache_valid any 1m; #fastcgi_cache_min_uses 1; #fastcgi_cache_use_stale error timeout invalid_header http_503; add_header X-Cache $upstream_cache_status; } I always get "MISS" and the cache dir is empty. If I uncomment the other directives, I get hit, but I don't want those "dumb" settings, I need to control them within my backend. For example, if my backend says "public, s-maxage=10", the cache should be considered stale after 10 secs. Instead, nginx will store it for 1h, because of these directives. I was thinking whether I should try proxy_cache, not sure what's the difference. In both fastcgi and proxy modules docs it says this: The cache honors backend's Cache-Control, Expires, and etc. since version 0.7.48, Cache-Control: private and no-store only since 0.7.66, though. Vary handling is not implemented. nginx version: nginx/1.1.19 Any thoughts? pd: I also have the reverse proxy that is offered by Symfony2 (which I turn off to use nginx's). The headers are interpreted correctly by it, so I think I'm doing it right.

  Read the article

• How do I change the default ftp folder in MacOS X 10.6?

  - by Wild_Eep

  I'm running WordPress 2.9.1 from a Mac running 10.6.3. WordPress is installed to the /Library/WebServer/Documents folder. WordPress has a feature called AutoUpdate. Clicking an autoupdate button will download and install updated versions of the WordPress software, or third-party plugin tools. It's a convenient way to keep things up to date. WordPress uses FTP to download the files. I've enabled FTP and set up a user account and opened the requisite ports in my firewall for FTP traffic. This doesn't seem to be enough for my self-hosted installation, though. I'm sure this feature was originally designed for someone who has access to a remote shared webserver, and that it's merely a configuration challenge related to the FTP setup. I feel that if I can adjust the initial directory that the FTP service presents to the AutoUpdate feature, everything else will work properly. So, my question is, how do I adjust what folder is presented when a given user connects to a Mac running 10.6.3 via FTP?

  Read the article

• External Dell Display doesn't work with MacBook Pro (2011) after Thunderbolt Firmware Update (1.0 and 1.2)

  - by tom

  Today two Thunderbolt Firmware Updates (1.0 and 1.2) became available for my MacBook Pro (Early 2011). After installing both, my external monitor, a Dell U2713HM, does no longer work. The system detects the display, but the display shows only black. An Apple Thunderbolt display works fine and a MacBook Air can use the Dell monitor without problems. My MacBook Pro can use the Dell monitor just fine when I boot from a USB stick. Therefore, clearly the Thunderbolt Firmware Update seems to be the problem. Does anyone have the same problem? Any solutions or workarounds? I guess there is no way to remove a Thunderbolt Firmware Update once it's installed, right? Update 24.10.2013: Is there no one else with this problem? In the meantime I tried three different cables – none worked. My colleague with the same generation MacBook Pro also can't use my display after installing the firmware update. All colleagues with MacBook Airs and newer MacBook Pros (all didn't receive the firmware update) can use the display. Update 29.10.2013: Wow, ok today my new MacBook Pro Retina 13' (Late 2013) arrived. Guess what, I cannot use the display with it. Only HDMI works – not with the full resolution.

  Read the article

• Only one domain is not resolving via Windows DNS server at multiple locations, but is at others

  - by Brett G

  I'm having quite a weird issue. Had mail delivery issues to a specific domain. After looking closer, I realized that the DNS for that domain isn't resolving via the in-house Windows 2003 SP2 DNS server. C:\>nslookup foodmix.net Server: DC.DOMAIN.com Address: 10.1.1.1 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to DC.DOMAIN.com timed-out (DC.DOMAIN.com and 10.1.1.1 are generic values to replace the actual ones) Even if I run this nslookup from the DC.DOMAIN.com server, I get the same result. However, all other requests are working as they should. I had a sysadmin friend try this DNS lookup on servers at several companies that he consults for (which are also Windows 2003 AD servers). The weird thing is some of these were having the same exact issue. However using public DNS servers work. I have tried clearing the DNS cache, restarting the server, restarting the services, etc. Nothing has worked. One weird event I noticed in the DNS Server Event Logs that might be related is an event ID of 5504 with the following description: The DNS server encountered an invalid domain name in a packet from 192.33.4.12. The packet will be rejected. The event data contains the DNS packet. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. In the data section below, I can see the following mentioned: ns2.webhostingstar.com Which happens to be the nameserver for the domain in question. Several discussion threads and a MS KB have pointed to disabling EDNS. I have done this via "dnscmd /config /enableednsprobes 0" and it has not fixed the issue.

  Read the article

• pfsense 2.0 traffic priority - set full priority for single host

  - by Waxhead

  I have a network with several computers all on the same network and since I have very limited bandwidth I would like to prioritize traffic almost like a CPU scheduler prioritize processes. Example: Computer A: Used for webstuff: YouTube, downloads, news, emails etc. Computer B: Transferring files over HTTP Computer C: Transferring files over ftp, rsync whatever What I would like to do is to give A up to for example 90% of the available bandwidth IF A requires it. The leftovers (10%) is divided between B and C (5% each if both is busy) If A is not utilizing all bandwidth then of course B and C should share the full bandwidth (50% each as long as both are maxing out their bandwidth). All computers are on the same network (192.168.1.0 - 192.168.1-10 for example). Appreciate if anyone could shed some light on how I should set up my network to achieve this. To be honest I actually need a step by step guide on how I should set this up. Network setup: (ADSL modem configured in bridge mode (1500kbps/300kbps)) [ADSL modem (bridge)]<-[pfsense2.0]<-[switch]<-[Computer A,B,C...etc]

  Read the article

• Computer making strange sound when turned on, ever since power outage

  - by Dot NET

  Recently we experienced a power outage, and the PC was off. However, once the power came back, I switched on the PC and heard a strange noise - almost as if the hard disk or fans were struggling to work. I can't really describe the sound, but it's a laboured, loud sound almost like a jack-hammer. This has been persisting ever since the power outage, however the noise stops after around 10 minutes or so, and doesn't start again until the computer is turned off and on again. At first I thought it had something to do with the HDD, but all my files are intact, chkdsk did not report any issues and performance is 100% unchanged, even in games (so the gfx card is fine, and so is the HDD most likely). My PC setup basically has around 3 cooling fans, but I'm not sure if it's one of these either as the noise actually stops after 10 minutes or so, and if I leave the PC on for 4 hours (for example) the noise never starts again. It's there solely when turning on the PC. I haven't got a UPS, and it's important to note that the computer was not on when the power went out - it was merely plugged in. I then promptly unplugged the PC once the power was out, and only plugged it in again when the power came back. Could it be the power supply? Unfortunately I can't open my tower as I would void the warranty. Are there any tests which I could carry out without voiding the warranty?

  Read the article

• VPS Memory Exchausted Even With Light Settings

  - by user101570

  Linux noob here. I have a 256MB VPS on Ubuntu 11.04 server and when I run "free -m" the result shows all memory being used (including the second line re: buffers/cache). I found this very strange, considering I only have 5 Apache processes running each chewing up about 20MB each. MYSQL is taking up 30MB. To my knowledge, and according to "top", I have no other memory hogs operating. Settings that may be relevant: PHP memory_limit = 32M MYSQL key_buffer = 16M Prefork MPM Maxclients = 10 So when I reviewed these settings, I naturally thought maxclients was too high, so I tried switching it to 5. Now not only does my memory still show as being 100% used, my website loads much, much slower, despite not getting any traffic aside from mine at the moment. I don't understand this. I thought a single Apache process handles all requests from a client received within the "KeepAliveTimeout" window, which I've set to 2 seconds. With my initial config. of 10 maxclients, my page load times are around .3ms, so a single process should handle that no problem, correct? So next I went to an extreme level of 1 for maxclients. My memory is still at 100% usage and my site loads painfully slow. I'm a noob at a complete loss here. According to the many tutorials I've read on basic server setup, I should be good to go. Help! Please! Edit: total used free shared buffers cached Mem: 256 256 0 0 0 0 -/+ buffers/cache: 256 0 Swap: 0 0 0

  Read the article

• VPS goes slow at more than 20 users online at the same time

  - by hachiari

  I have 512 MB VPS (brustable to 1GB) Somehow, the site goes slow when there are about 10 users, and becomes impossible to load at 20 users online at the same time. I wonder what could be the problem for this. The bandwidth connection of the VPS is 1Gbps. Here is some settings in my VPS: KeepAlive Off <IfModule prefork.c> StartServers 7 MinSpareServers 7 MaxSpareServers 10 ServerLimit 64 MaxClients 64 MaxRequestsPerChild 0 </IfModule> my.cnf settings - calculated Max Memory 300MB Output from UNIXBENCH INDEX VALUES TEST BASELINE RESULT INDEX Dhrystone 2 using register variables 376783.7 13429727.4 356.4 Double-Precision Whetstone 83.1 1137.5 136.9 Execl Throughput 188.3 1637.4 87.0 File Copy 1024 bufsize 2000 maxblocks 2672.0 148868.0 557.1 File Copy 256 bufsize 500 maxblocks 1077.0 79430.0 737.5 File Read 4096 bufsize 8000 maxblocks 15382.0 1410009.0 916.7 Pipe Throughput 111814.6 4419722.0 395.3 Pipe-based Context Switching 15448.6 561505.1 363.5 Process Creation 569.3 10272.7 180.4 Shell Scripts (8 concurrent) 44.8 514.3 114.8 System Call Overhead 114433.5 3537373.8 309.1 ========= FINAL SCORE 295.0 I am afraid that the VPS company limit the number of connection to the VPS... is it possible? The server is in Japan, but the site has global traffic (some of the traffic are from countries with low speed connection). Could this be the problem? This is a serious problem :( my site just cant grow if this keeps on happening... please tell me if you have any idea. Thank You, Bryant

  Read the article

• Quickly close all Word and Excel instances?

  - by dyenatha

  Suppose I open 10 Word files and 10 Excel files and make no changes, how do I quickly taskkill all at once? Because I must repeat several attempts to replicate race, I'm hoping for a command-line solution. I'm willing to try PowerShell and cygwin (1.5) if necessary. The OS is Windows XP SP3 with current patches (still IE7). I tried "taskkill /pid 1 /pid 2 /t" where 1 is PID of EXCEL.EXE and 2 is PID of WINWORD.EXE, but it closed only 1 window of each program. I'm trying to replicate a race where an add-in for Microsoft Office 2007 fails to exclusive-lock one of its own files, which caused the 2nd Office program to stop exiting with a warning: System.IO.IOException: The process cannot access the file 'C:\Documents and Settings\me\Application Data\ExpensiveProduct\Add-InForMicrosoftOffice\4.2\egcred' because it is being used by another process. at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath) at System.IO.FileStream.Init(String path, FileMode mode, FileAccess access, Int32 rights, Boolean useRights, FileShare share, Int32 bufferSize, FileOptions options, SECURITY_ATTRIBUTES secAttrs, String msgPath, Boolean bFromProxy) at System.IO.FileStream..ctor(String path, FileMode mode, FileAccess access, FileShare share, Int32 bufferSize, FileOptions options) at System.IO.StreamWriter.CreateFile(String path, Boolean append) at System.IO.StreamWriter..ctor(String path, Boolean append, Encoding encoding, Int32 bufferSize) at System.IO.StreamWriter..ctor(String path, Boolean append, Encoding encoding) at System.IO.File.WriteAllText(String path, String contents, Encoding encoding) at ExpensiveProduct.EG.DataAccess.Credentials.CredentialManager.SaveUserTable() at ExpensiveProduct.OfficeAddin.OfficeAddinBase.Dispose(Boolean disposing) at ExpensiveProduct.OfficeAddin.WordAddin.Dispose(Boolean disposing) at ExpensiveProduct.OfficeAddin.OfficeAddinBase.OnHostShutdown() at ExpensiveProduct.OfficeAddin.OfficeAddinBase.Unload(ext_DisconnectMode mode)

  Read the article

• Do I need to update some of my Debian Squeeze software?

  - by stan31337

  I have installed Debian 6, and LAMP stack from squeeze repository (default). After upgrading Apache 2.2.16 from unstable repository to 2.2.22, thanks to this post - how to upgrade already installed apache2 on debian (lenny) I'm thinking to upgrade all other software packages that I've previously installd from squeeze repository. Should I upgrade them to the ones from unstable repository? Should I upgrade all of them or just selected ones? Here's the list: * arno-iptables-firewall 1.9.2.k-4 >> 2.0.1.c-1 * bind9 1:9.7.3.dfsg-1~squeeze6 >> 1:9.8.1.dfsg.P1-4.2 * php-apc 3.1.3p1-2 >> 3.1.13-1 * fail2ban 0.8.4-3+squeeze1 >> 0.8.6-3 * exim4 4.72-6+squeeze2 >> 4.80-4 * altermime 0.3.10-4 >> 0.3.10-7 * rrdtool 1.4.3-1 >> 1.4.7-2 * vsftpd 2.3.2-3+squeeze2 >> 3.0.0-4 Also I would like to ask how to upgrade 5.3.3 5.3.16, unstable repository has 5.4.x versions only, I don't think I'm ready to move from 5.3 to 5.4 yet. Actually I'm a newbie in Linux, and after Windows experience I have a paranoidal idea to update software to the latest release. I'd be glad for any suggestions and recommendations! Thank you very much!

  Read the article

• AA doesn't work due to monitor?

  - by MikeQ

  I have a monitor (with TV tuner - Philips 221T1SB), native resolution of 1920x1080, but there is an Overscan in Catalyst. It says from left to right '10%' and '0%', if i set it (all the way to the left) on 10%, i get screen with black borders (you know what i mean), but if i set it to 0%, i get a filled monitor. It does make sense, but why the hell is there such an option? I never had any AA issues before, but now, with this monitor, here they go. I can't find any solution, i have only one lead = overscan, or pretty much anything with the CCC settings. Yes, i almost forgot. After a bit of trying to configure the monitor with remote, i found there is a PC channel option, few other channels, and then a HDMI option. I have monitor through HDMI, but why i get black screen when i select the PC channel? That might be another problem. I tried almost everything. Please guys, give me a hand. I don't want jaggies! CPU: Intel I5-750 @4,0GHz RAM: Corsair Vengeance 8GB 1600MHz GPU: AMD Gigabyte HD 7950 Windforce @1100/1400, 1,174V Motherboard: ASUS P7P55D-E EVO

  Read the article

< Previous Page | 442 443 444 445 446 447 448 449 450 451 452 453  | Next Page >