Search Results

Search found 11938 results on 478 pages for 'secure boot'.

Page 453/478 | < Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >

• Can't manage iPod from linux anymore

  - by kemp

  I used to be able to see and manage my iPod with different softwares: Amarok, Rhythmbox, GTKPod. The device is a nano 1st generation 4gb. Currently it mounts regularly and can be accessed from the file system, but I get this in dmesg: [ 1547.617891] scsi 11:0:0:0: Direct-Access Apple iPod 1.62 PQ: 0 ANSI: 0 [ 1547.619103] sd 11:0:0:0: Attached scsi generic sg2 type 0 [ 1547.620478] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.620494] sd 11:0:0:0: [sdb] 7999487 512-byte hardware sectors: (4.09 GB/3.81 GiB) [ 1547.621718] sd 11:0:0:0: [sdb] Write Protect is off [ 1547.621726] sd 11:0:0:0: [sdb] Mode Sense: 68 00 00 08 [ 1547.621732] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.623591] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.624993] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.625003] sdb: sdb1 sdb2 [ 1547.629686] sd 11:0:0:0: [sdb] Attached SCSI removable disk [ 1548.084026] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.369502] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.504358] FAT: invalid media value (0x2f) [ 1548.504363] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1548.945173] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.945179] FAT: invalid media value (0x2f) [ 1548.945182] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1610.092886] usb 2-6: USB disconnect, address 9 The only application that can access it (partially) is Rhythmbox. I say partially because I can transfer files to the iPod but can't remove or modify them. Also one transfer didn't finish and only 9 out of 16 songs were delivered to the device. All other softwares I tried (GTKPod, Amarok, Songbird) don't even detect it. What can I do to troubleshoot this? EDIT: # fdisk -l /dev/sdb Disk /dev/sdb: 4095 MB, 4095737344 bytes 241 heads, 62 sectors/track, 535 cylinders Units = cylinders of 14942 * 512 = 7650304 bytes Disk identifier: 0x20202020 Device Boot Start End Blocks Id System /dev/sdb1 1 11 80293+ 0 Empty Partition 1 has different physical/logical beginnings (non-Linux?): phys=(0, 1, 1) logical=(0, 1, 2) Partition 1 has different physical/logical endings: phys=(9, 254, 63) logical=(10, 181, 8) Partition 1 does not end on cylinder boundary. /dev/sdb2 11 536 3919415+ b W95 FAT32 Partition 2 has different physical/logical beginnings (non-Linux?): phys=(10, 0, 7) logical=(10, 181, 15) Partition 2 has different physical/logical endings: phys=(497, 240, 62) logical=(535, 88, 61) EDIT2: The "before" state is hard to tell, it was a lot of updates ago. Haven't been using my iPod for a while so I can't say when exactly it stopped working. I'm sure Amarok was still at version 1.X but can't remember when it was. My current system is debian testing fully updated. NOTE: just noticed that if I mount the device manually instead of letting nautilus automount it, I can see it again on GTKPod but still not on Banshee AND it's vanished from Rhythmbox...

  Read the article

• Adaptec 5805 after reboot don't starting

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not included. It only works if the computer is shut down and turn off. Late i update firmware "Adaptec RAID 5805 Firmware Build 18948" How to fix the problem? add Log Configuration summary Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priorityHigh Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1 List item

  Read the article

• Windows 7 remains powered on when restarting

  - by BombDefused

  I'm running windows 7 x64 on an MSI P67A-GD53 motherboard, in an Antec P280 Super Midi Towercase with a Corsair 650w PSU. I've just installed a second instance of windows 7 x64 on a separate disk (this is to keep my games separate from my work OS). The problem is that it appears now that I cannot restart from either instance of Windows 7. The shut down command, and sleep commands work as expected. When I try to restart, the shutdown happens but the system never reboots. Everything remains powered on, until I hold down the power button to force the power off. Ithink (but am not 100% sure) this has only started since I installed the second OS, and am assuming this has something to do with the motherboard needing to know which OS to run up again? Some other forums I've read suggest that the PSU has a major role in restart and could be at fault. Changing the boot order of the disks in the BIOS does not change anything. Any suggestions greatfully recieved! Update: I now have a reproduceable issue: I think the secondary OS install may have been a red herring. It was when windows tried to reboot during the install that I noticed the issue. After playing around with installing drivers, and rebooting many many times, I have found that it is the OC genie setting on the MSI motherboard that seems to trigger the problem. This makes sense as I only started using the OC genie feature a couple of weeks ago, and probably hadn't used restart in that time. However... simply turning off OC genie does not make the issue go away. I have to turn off OC genie, shutdown, start enter bios, go to the "Save and Exit" menu "Restore Defaults" yes to "Load optimized defaults", which will reset to clear the problem. Now when the PC boots into windows, I can restart as normal (and from the OS on either HDD). I only know how to control the issue, and don't still know the root cause. I'd like to be able to use the OC genie function if anyone can suggest a why I'm seeing this problem. Could it be that I'm drawing too much power when using OC feature?

  Read the article

• Deleting windows.edb and unchecking Indexing service lead to hard drive file records swapping

  - by linni

  I followed the instructions listed here:http://www.mydigitallife.info/2007/09/18/turn-off-and-disable-search-indexing-service-in-windows-xp/ to free up space on hard drive by deleting the windows.edb indexing file... I also stopped windows search service as mentioned in the comments following the article. In addition to unchecking the "Allow Indexing Service to index this disk for fast file searching" check box on the properties dialog for the C:\ drive, I did the same for two usb connected hard drives (J:\ and I:\ ). I'm not sure why I did that, thought it might shrink the windows.edb file so I wouldn't have to delete it (which sounded a bit risky in my ears at the time). The file of course didn't shrink so I ended up deleting it and freeing up over 3 GB of space, yeehaw. However, as soon as I had done this I could not access the usb connected hard drives anymore. The error I got was "I:\photos is not accessible" "The file or directory is corrupted and unreadable" when I tried to open the photos directory on I:\ Here is where I enter the twilight zone... I try disconnecting I:\ usb hard drive. But XP shows me that instead J:\ drive has disconnected and I:\ is still there. So I disconnect both drives and restart the computer. I then connect one drive, but it lists up the contents of the other drive on root level. I tried connecting the drives vice versa and the same thing happens. I try taking one of the hard drives to another computer and when I connect it there it lists up not its own contents but the contents of the other hard drive and gives the same error as above when I try and access any of the folders (even folders on the root that have the same name as folders on the other drive (e.g. J:\photos and I:\photos)??? And no, this is not a me mixing up my drive letters. Computer Manager - Disk management shows the same result as explorer: The drive size is correct (one is 500GB, the other is 640GB) but the drive name is of the opposite drive, as long as the contents. Also, one drive was full of data and the other almost empty but they incorrectly show their free space status of the other drive. Somehow the usb drives seem to have switched file tables, file records, boot records or something, extremely weird! Even weirder, if I try and create a text file or folder on this drive, it works fine, accessing them, saving, whatever, all good, but accessing any other data on the drive gives me an error. Does anyone have a clue what is going on and more importantly, how I can restore the correct folder listings to access my family photos ??? cheers, linni

  Read the article

• http.conf setup to simplify using 'localhost:81'

  - by Will

  I'm installing portable wampserver within my dropbox folder so I can access anywhere. I have this achieved and accessible using http://locahost:81 I want to access it by using a different address (dropping the :81 port number) such as http://myothersite. I'm fairly certain I need to add a virtualhosts directove somewhere within this, but I am not Apache experienced! This is the current Apache httpd.conf file: ServerRoot "C:/Users/will/Dropbox/Wampee-2.1-beta-2/bin/apache/apache2.2.17" Listen 81 ServerAdmin admin@localhost ServerName localhost:81 DocumentRoot "C:/Users/will/Dropbox/Wampee-2.1-beta-2/www/" <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Deny from all </Directory> <Directory "C:/Users/will/Dropbox/Wampee-2.1-beta-2/www/"> Options Indexes FollowSymLinks AllowOverride all # onlineoffline tag - don't remove Order Deny,Allow Deny from all Allow from 127.0.0.1 </Directory> <IfModule dir_module> DirectoryIndex index.php index.php3 index.html index.htm </IfModule> <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> ErrorLog "C:/Users/will/Dropbox/Wampee-2.1-beta-2/logs/apache_error.log" LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog "C:/Users/will/Dropbox/Wampee-2.1-beta-2/logs/access.log" common #CustomLog "logs/access.log" combined </IfModule> <IfModule alias_module> ScriptAlias /cgi-bin/ "cgi-bin/" </IfModule> <IfModule cgid_module> #Scriptsock logs/cgisock </IfModule> <Directory "cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig conf/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz AddType application/x-httpd-php .php AddType application/x-httpd-php .php3 </IfModule> # Server-pool management (MPM specific) #Include conf/extra/httpd-mpm.conf # Multi-language error messages #Include conf/extra/httpd-multilang-errordoc.conf # Fancy directory listings Include conf/extra/httpd-autoindex.conf # Language settings #Include conf/extra/httpd-languages.conf # User home directories #Include conf/extra/httpd-userdir.conf # Real-time info on requests and configuration #Include conf/extra/httpd-info.conf # Virtual hosts #Include conf/extra/httpd-vhosts.conf # Local access to the Apache HTTP Server Manual #Include conf/extra/httpd-manual.conf # Distributed authoring and versioning (WebDAV) #Include conf/extra/httpd-dav.conf # Various default settings #Include conf/extra/httpd-default.conf # Secure (SSL/TLS) connections #Include conf/extra/httpd-ssl.conf # # Note: The following must must be present to support # starting without SSL on platforms with no /dev/random equivalent # but a statically compiled-in mod_ssl. # <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> Include "C:/Users/will/Dropbox/Wampee-2.1-beta-2/alias/*" Include "C:/Users/will/Dropbox/Wampee-2.1-beta-2/MyWebAp ps/etc/alias/*"

  Read the article

• Windows 7 Bluescreen: IRQ_NOT_LESS_OR_EQUAL | athrxusb.sys

  - by wretrOvian

  I'd left my system on last night, and found the bluescreen in the morning. This has been happening occasionally, over the past few days. Details: ================================================== Dump File : 022710-18236-01.dmp Crash Time : 2/27/2010 8:46:44 AM Bug Check String : DRIVER_IRQL_NOT_LESS_OR_EQUAL Bug Check Code : 0x000000d1 Parameter 1 : 00000000`00001001 Parameter 2 : 00000000`00000002 Parameter 3 : 00000000`00000000 Parameter 4 : fffff880`06b5c0e1 Caused By Driver : athrxusb.sys Caused By Address : athrxusb.sys+760e1 File Description : Product Name : Company : File Version : Processor : x64 Computer Name : Full Path : C:\Windows\minidump\022710-18236-01.dmp Processors Count : 2 Major Version : 15 Minor Version : 7600 ================================================== HiJackThis ("[...]" indicates removed text; full log [posted to pastebin][1]): Logfile of Trend Micro HijackThis v2.0.2 Scan saved at 8:49:15 AM, on 2/27/2010 Platform: Unknown Windows (WinNT 6.01.3504) MSInternet Explorer: Internet Explorer v8.00 (8.00.7600.16385) Boot mode: Normal Running processes: C:\Windows\DAODx.exe C:\Program Files (x86)\Asus\EPU\EPU.exe C:\Program Files\Asus\TurboV\TurboV.exe C:\Program Files (x86)\PowerISO\PWRISOVM.EXE C:\Program Files (x86)\OpenOffice.org 3\program\soffice.exe C:\Program Files (x86)\OpenOffice.org 3\program\soffice.bin D:\Downloads\HijackThis.exe C:\Program Files (x86)\uTorrent\uTorrent.exe R1 - HKCU\Software\Microsoft\Internet Explorer\[...] [...] O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files (x86)\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [HDAudDeck] C:\Program Files (x86)\VIA\VIAudioi\VDeck\VDeck.exe -r O4 - HKLM\..\Run: [StartCCC] "C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static\CLIStart.exe" MSRun O4 - HKLM\..\Run: [TurboV] "C:\Program Files\Asus\TurboV\TurboV.exe" O4 - HKLM\..\Run: [PWRISOVM.EXE] C:\Program Files (x86)\PowerISO\PWRISOVM.EXE O4 - HKLM\..\Run: [googletalk] C:\Program Files (x86)\Google\Google Talk\googletalk.exe /autostart O4 - HKLM\..\Run: [AdobeCS4ServiceManager] "C:\Program Files (x86)\Common Files\Adobe\CS4ServiceManager\CS4ServiceManager.exe" -launchedbylogin O4 - HKCU\..\Run: [uTorrent] "C:\Program Files (x86)\uTorrent\uTorrent.exe" O4 - HKUS\S-1-5-19\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-19\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-20\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'NETWORK SERVICE') O4 - HKUS\S-1-5-20\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'NETWORK SERVICE') O4 - Startup: OpenOffice.org 3.1.lnk = C:\Program Files (x86)\OpenOffice.org 3\program\quickstart.exe O13 - Gopher Prefix: O23 - Service: @%SystemRoot%\system32\Alg.exe,-112 (ALG) - Unknown owner - C:\Windows\System32\alg.exe (file missing) O23 - Service: AMD External Events Utility - Unknown owner - C:\Windows\system32\atiesrxx.exe (file missing) O23 - Service: Asus System Control Service (AsSysCtrlService) - Unknown owner - C:\Program Files (x86)\Asus\AsSysCtrlService\1.00.02\AsSysCtrlService.exe O23 - Service: DeviceVM Meta Data Export Service (DvmMDES) - DeviceVM - C:\Asus.SYS\config\DVMExportService.exe O23 - Service: @%SystemRoot%\system32\efssvc.dll,-100 (EFS) - Unknown owner - C:\Windows\System32\lsass.exe (file missing) O23 - Service: ESET HTTP Server (EhttpSrv) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\EHttpSrv.exe O23 - Service: ESET Service (ekrn) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\x86\ekrn.exe O23 - Service: @%systemroot%\system32\fxsresm.dll,-118 (Fax) - Unknown owner - C:\Windows\system32\fxssvc.exe (file missing) O23 - Service: FLEXnet Licens

  Read the article

• "Error loading operating system": Win7/Vista

  - by LookitsPuck

  Have this computer for about 2 years now. Originally had Vista installed, now have Windows 7 installed. Both on separate hard drives. Also have another drive used strictly for media. About a week ago, the Vista hard drive started going on its way out. Was getting problems on startup. After a few BIOS settings, I was able to get into Windows 7 and everything was fine. However, I started remembering the startup issues, so I deleted the bootup for Vista under msconfig. Didn't restart the computer at that time, though. For a few days, everything was ok. Last night I play a little poker, then hit the hay. I wake up to a good ole "Error loading operating system" on the screen. Just wonderful. Looks like the computer restarted overnight (auto updates, anyone?). So, after a big of finagling and half hearted tries, I can't get past the "Error loading operating system" screen. FWIW, in the BIOS it can see my hard drives fine. So I move on. I get my Windows 7 installation disk to try and do a repair. Go in the BIOS, change boot priority to DVD drive, and we're on our merry way. After loading from the disc, I first try jumping into the "Repair your computer" section. That opens up the System Recovery Options. However, this is where the problem comes into play. I don't see any operating systems here. Nada. What's odd though is if I click on the Load Drivers button, I can see my Windows 7 partition (C:), and can go through the files and folders without issue. What do I do at this point? I can't repair it. It seems like I can traverse the hard drive without issue when in an open dialog in the System Recovery Options, but I'm getting the good ole "Error loading computer" on bootup. Suggestions? Thanks all!!

  Read the article

• external hard drive is no longer recognized, gives buffer I/O errors

  - by BioGeek

  Hi all, The external hard drive which contains all my photos and where I backed-up all my important documents is no longer recognized. It is a three month old 500GB Iomage Prestige Desktop Hard Drive. When I plug it in, it is recognised as a USB device, because it shows up when I type lsusb, but dmesg gives this error message. [19712.013250] usb 2-2: new high speed USB device using ehci_hcd and address 21 [19712.145347] usb 2-2: configuration #1 chosen from 1 choice [19712.147214] scsi25 : SCSI emulation for USB Mass Storage devices [19712.147514] usb-storage: device found at 21 [19712.147519] usb-storage: waiting for device to settle before scanning [19717.148978] usb-storage: device scan complete [19717.149527] scsi 25:0:0:0: Direct-Access ST350082 0AS PQ: 0 ANSI: 2 CCS [19717.151020] sd 25:0:0:0: Attached scsi generic sg2 type 0 [19717.151685] sd 25:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) [19717.160402] sd 25:0:0:0: [sdb] Write Protect is off [19717.160412] sd 25:0:0:0: [sdb] Mode Sense: 34 00 00 00 [19717.160418] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165685] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165691] sdb: sdb1 [19719.171808] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19719.171818] sd 25:0:0:0: [sdb] Attached SCSI disk [19737.430998] sd 25:0:0:0: [sdb] Unhandled sense code [19737.431007] sd 25:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [19737.431016] sd 25:0:0:0: [sdb] Sense Key : Medium Error [current] [19737.431027] sd 25:0:0:0: [sdb] Add. Sense: Unrecovered read error [19737.431038] end_request: I/O error, dev sdb, sector 6160463 [19737.431050] Buffer I/O error on device sdb1, logical block 6160400 [19737.431060] Buffer I/O error on device sdb1, logical block 6160401 [19737.431067] Buffer I/O error on device sdb1, logical block 6160402 [19737.431075] Buffer I/O error on device sdb1, logical block 6160403 [19737.431082] Buffer I/O error on device sdb1, logical block 6160404 [19737.431088] Buffer I/O error on device sdb1, logical block 6160405 [19737.431096] Buffer I/O error on device sdb1, logical block 6160406 [19737.431102] Buffer I/O error on device sdb1, logical block 6160407 [19737.431114] Buffer I/O error on device sdb1, logical block 6160408 [19737.431121] Buffer I/O error on device sdb1, logical block 6160409 [19737.712183] sd 6:0:0:0: [sdb] Unhandled sense code [19737.712191] sd 6:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [19737.712200] sd 6:0:0:0: [sdb] Sense Key : Hardware Error [current] [19737.712210] sd 6:0:0:0: [sdb] Add. Sense: No additional sense information [19737.712222] end_request: I/O error, dev sdb, sector 0 [19737.712232] Buffer I/O error on device sdb, logical block 0 Neither does the external drive show when I use fdisk: jeroen@phalacrocorax:~$ sudo fdisk -l [sudo] password for jeroen: Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000341ad Device Boot Start End Blocks Id System /dev/sda1 * 1 18714 150320173+ 83 Linux /dev/sda2 18715 19457 5968147+ 5 Extended /dev/sda5 18715 19457 5968116 82 Linux swap / Solaris` I popped the disk out of the casing put it on a SATA connect internally and then tried the file recovery programs testdisk/photorec and SpinRite, but both failed because they couldn't recognize the external harddisk. Do I have any other options?

  Read the article

• What Apache/PHP configurations do you know and how good are they?

  - by FractalizeR

  Hello. I wanted to ask you about PHP/Apache configuration methods you know, their pros and cons. I will start myself: ---------------- PHP as Apache module---------------- Pros: good speed since you don't need to start exe every time especially in mpm-worker mode. You can also use various PHP accelerators in this mode like APC or eAccelerator. Cons: if you are running apache in mpm-worker mode, you may face stability issues because every glitch in any php script will lead to unstability to the whole thread pool of that apache process. Also in this mode all scripts are executed on behalf of apache user. This is bad for security. mpm-worker configuration requires PHP compiled in thread-safe mode. At least CentOS and RedHat default repositories doesn't have thread-safe PHP version so on these OSes you need to compile at least PHP yourself (there is a way to activate worker mpm on Apache). The use of thread-safe PHP binaries is considered experimental and unstable. Plus, many PHP extensions does not support thread-safe mode or were not well-tested in thread-safe mode. ---------------- PHP as CGI ---------------- This seems to be the slowest default configuration which seems to be a "con" itself ;) ---------------- PHP as CGI via mod_suphp ---------------- Pros: suphp allows you to execute php scipts on behalf of the script file owner. This way you can securely separate different sites on the same machine. Also, suphp allows to use different php.ini files per virtual host. Cons: PHP in CGI mode means less performance. In this mode you can't use php accelerators like APC because each time new process is spawned to handle script rendering the cache of previous process useless. BTW, do you know the way to apply some accelerator in this config? I heard something about using shm for php bytecode cache. Also, you cannot configure PHP via .htaccess files in this mode. You will need to install PECL htscanner for this if you need to set various per-script options via .htaccess (php_value / php_flag directives) ---------------- PHP as CGI via suexec ---------------- This configuration looks the same as with suphp, but I heard, that it's slower and less safe. Almost same pros and cons apply. ---------------- PHP as FastCGI ---------------- Pros: FastCGI standard allows single php process to handle several scripts before php process is killed. This way you gain performance since no need to spin up new php process for each script. You can also use PHP accelerators in this configuration (see cons section for comment). Also, FCGI almost like suphp also allows php processes to be executed on behalf of some user. mod_fcgid seems to have the most complete fcgi support and flexibility for apache. Cons: The use of php accelerator in fastcgi mode will lead to high memory consumption because each PHP process will have his own bytecode cache (unless there is some accelerator that can use shared memory for bytecode cache. Is there such?). FastCGI is also a little bit complex to configure. You need to create various configuration files and make some configuration modifications. It seems, that fastcgi is the most stable, secure, fast and flexible PHP configuration, however, a bit difficult to be configured. But, may be, I missed something? Comments are welcome!

  Read the article

• XP OEM licensing when reinstalling Windows XP

  - by mindas

  My wife has managed to buy a Dell laptop she was using at her ex-employer that just went bust. The problem with it is the OS (Windows XP) which takes ages to boot and is generally disproportionally slow to the hardware of the machine. So my aim is to sacrifice a day and reinstall it. The problem I am slightly worried about is the licensing/registration/activation hell. Apart from the sticker (with WinXP license key), the laptop has no other paperwork proving this license is legitimate. I believe this was originally an OEM license. Unfortunately, I don't have the the installation CD. This computer also has MS Office installed (which I would like to retain) but it none of MS Office apps would launch due to some obscure error complaining about lack of free disk space (which computer has plenty of). I have absolutely no clue what kind of license this MS Office was. And because the company has gone into the administration, there is no way of getting this information nor installable media. I believe that by buying the hardware I have also acquired the software which I can use as I see fit. Correct me if I'm wrong. Above said, my question would be: What is the easiest way of reinstalling the XP? By easiest I mean avoiding spending my time to prove Microsoft support I've got the right to use the software (insert your computer says noooo joke here) but still being able to get to fresh virgin activated legal state of the XP. I used to work as a sysadmin many years ago so I am not afraid of any technical difficulties. The same question applies to MS Office. I imagine the process would consist of backing up all the data, pulling some bits from the registry and using that on the fresh install. As for reinstall I'd expect to use some sort of OEM Windows repair CD from Dell, right? Are those freely available? My other box (HP) has such a thing and it can't be used on any other brand. I'm sure somebody had to go through this licensing hell and could share his/her tips. Thanks in advance.

  Read the article

• Logitech Optical Mouse Frozen In Middle of Windows XP Pro Screen

  - by Code Sherpa

  I have a Logitech Optical Mouse/Keyboard. I have been using them just fine with the system drivers for almost a year now. I recently updated my Kaspersky software and rebooted. Now the mouse is frozen in the middle of my screen. I am not able to login to the Windows XP Pro box that has the frozen mouse (because i can't work the mouse) but am able to remote desktop to this computer. Things I know / have tried: When I boot on the problem computer, I am able to use the keyboard, but not the mouse. I have installed the latest version of Logitech's SetPoint (with the updated drivers) on the problem computer (via remote desktop) and that didn't seem to matter. I bought new batteries for the mouse and that didn't matter. I have tried the mouse/keyboard on another computer and the mouse works just fine there. My suspicion is that the Kaspersky install has overwritten a driver of some sort. Things I have not done (and would appreciate detailed steps if you feel this is the way to go): 1) Uninstalled all the mouse drivers on the machine and reboot. Then, reinstall. Note: When I get to the Device Manager I don't see an option for Human Interface Devices (where the mouse device is). Here are my options: Computer, Disk Drives, DVD/CD-Rom drives, Floppy controllers, IDE ATA/ATAPI, Imaging devices, Network Adapters, Other devices, Ports, Processors, Sound, video, and gaming, System devices, USB controllers. Also, I should point out that Video Controller is the only thing under Other devices and it has a yellow exclamation mark. The same is true for all the items under Universal Serial Bus controllers. I think this means I have to update my BIOS but, since my mouse was working just fine without doing that, I don't think that is my problem. So, how do I get to my Mouse Device? 2) Update my BIOS. Note: As pointed out above, I don't think this matters as my mouse was working just fine under my computer's current BIOS version. Thanks for your help.

  Read the article

• Tutorial for configuring OpenVPN [on hold]

  - by user2699451

  I have been through 10+ tutorials on setting up a OpenVPN, and each tutorial gives a different problem... Does anyone know of a decent and helpful website/tutorial which I could go to to get it set up? I have been battling through it for almost 2 months now. Yes, I have also bugged forums.openvpn, but I think I have "reached my post limit" with them. I have to configure it remotely via ssh. UPDATE: okay, I have been asked to be more clear on the topic I followed this tutorial (as a example) - http://www.servermom.com/how-to-build-openvpn-server-on-centos-6-x/732/ I had no issues setting up, etc. except when I boot into windows and run the OpenVPN GUI Client, it connects and gives this error: WARNING: Bad encapsulated packet length from peer (21331), which must be 0 and <= 1576 -- please ensure that --tun-mtu or --link-mtu is equal on both peers -- this condition could also indicate a possible active attack on the TCP link -- [Attemping restart...] Here is my server config: port 1194 #- port proto udp #- protocol dev tun tun-mtu 1500 tun-mtu-extra 32 mssfix 1450 reneg-sec 0 ca /etc/openvpn/easy-rsa/2.0/keys/ca.crt cert /etc/openvpn/easy-rsa/2.0/keys/server.crt key /etc/openvpn/easy-rsa/2.0/keys/server.key dh /etc/openvpn/easy-rsa/2.0/keys/dh1024.pem plugin /usr/lib64/openvpn/plugin/lib/openvpn-auth-pam.so /etc/pam.d/login #- Co$ #plugin /etc/openvpn/radiusplugin.so /etc/openvpn/radiusplugin.cnf #- Uncomment$ client-cert-not-required username-as-common-name server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" keepalive 5 30 comp-lzo persist-key persist-tun status 1194.log verb 3 and my client config: client dev tun proto udp remote [server ip] 1194 # - Your server IP and OpenVPN Port resolv-retry infinite nobind tun-mtu 1500 tun-mtu-extra 32 mssfix 1450 persist-key persist-tun ca ca.crt auth-user-pass comp-lzo reneg-sec 0 verb 3 OpenVPN Client Log: Thu Oct 31 11:51:29 2013 OpenVPN 2.0.9 Win32-MinGW [SSL] [LZO] built on Oct 1 2006 Thu Oct 31 11:51:44 2013 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Thu Oct 31 11:51:44 2013 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Thu Oct 31 11:51:44 2013 LZO compression initialized Thu Oct 31 11:51:44 2013 Control Channel MTU parms [ L:1576 D:140 EF:40 EB:0 ET:0 EL:0 ] Thu Oct 31 11:51:44 2013 Data Channel MTU parms [ L:1576 D:1450 EF:44 EB:135 ET:32 EL:0 AF:3/1 ] Thu Oct 31 11:51:44 2013 Local Options hash (VER=V4): '2547efd2' Thu Oct 31 11:51:44 2013 Expected Remote Options hash (VER=V4): '77cf0943' Thu Oct 31 11:51:44 2013 Attempting to establish TCP connection with x.x.x.x:1194 Thu Oct 31 11:51:44 2013 TCP connection established with x.x.x.x:1194 Thu Oct 31 11:51:44 2013 TCPv4_CLIENT link local: [undef] Thu Oct 31 11:51:44 2013 TCPv4_CLIENT link remote: x.x.x.x:1194 // after this it just hangs, nothing happens So I dont know what I am doing wrong but I am getting a bit impatient and on each forum I post this, I get stupid/unrelated/unhelpful answers...

  Read the article

• Ubuntu Server 10.04 Heavy Network Traffic causes disconnect

  - by K Vaughan

  I'm currently running a headless Ubuntu 10.04 server. Installed is the LAMP stack, Joomla, Virtualbox, phpvirtualbox, webmin and proFTP.. It resolves the IP address so I can access it remotely (either the apache2 webserver or the FTP) using DDClient. Any packages installed have been installed using apt-get. Webmin, although discouraged in Ubuntu Server, is used mostly to administer the webserver aspect. This issue also appeared when I was using Ubuntu Server 10.10. After periods of heavy network traffic, whether local or remote, the connect drops. I'm talking specifically about the transfer of files via FTP, SCP or Samba (the latter of which I seldom use). There is no response to ping or ssh. I can't FTP to the server nor can I load the website. There are times when the server has been on for a few days and everything runs fine because I haven't accessed it much, if at all (thus not much network traffic). I've gone through a few hardware changes although I don't believe this has cause the issue: this has been happening long before I made any changes. At first I thought it was my ISP-provided router blocking traffic because of some kind of misconfiguration (perhaps assuming it was some kind of DoS attack). I've changed routers and still found no success. I've checked syslog, dmesg and kern.log for warnings but have uncovered none. I've ran memtest via the GRUB2 menu at boot and once it turned up 4 errors. I ran again with individual sticks of RAM in various slots and everything turned up fine. I've looked through the BIOS settings and everything looks fine. I've tried unplugging unnecessary pieces of hardware (other internal hard drives, CD drives, floppy, PCI cards, etc). Any help or tips on how I can even begin to troubleshoot this would be very much appreciated. Please note that i've only started playing with servers as a hobby so my knowledge wouldn't be the most refined. I'm comfortable with command line and have the initiative to know how to look up something I can't do. Unfortunately I can't seem to find any issues like this. Additionally: If a solution can't be found some assistance to write a script that will cause the server to reboot automatically if, after x minutes, it gets no response to pinging somewhere like google. Admittedly that's not the cleanest solution should my internet end up going down but I can't think of what else to do.

  Read the article

• Securing smtp with login

  - by Paul Peelen

  I have a ispconfig server, and it seems that someone is using it to send spam. I got about 130 "Mail Delivery System" email about declined send email. This spammer uses my email address as sent from adress, so I get all these email adresses to my mail. I am using Postfix and Courier. I installed my server according to this guide: http://www.howtoforge.com/perfect-server-debian-lenny-ispconfig3-p3 I did this a few months ago. My question: Can I secure my server to require login to be able to send email, and if so... how? Thanks! EDIT Some data from mail.log, these kind of error show up constantly: Jun 15 17:58:16 bolt postfix/qmgr[10712]: CC7DA1242AE: from=<paul@*****.se>, size=3782, nrcpt=1 (queue active) Jun 15 17:58:16 bolt postfix/smtp[11337]: CC7DA1242AE: to=<[email protected]>, relay=none, delay=4641, delays=4640/0.01/0.32/0, dsn=4.4.3, status=deferred (Host or domain name not found. Name service error for name=cmlisboa.pt type=MX: Host not found, try again) Jun 15 17:58:19 bolt postfix/smtpd[10836]: connect from static-200-105-220-154.acelerate.net[200.105.220.154] Jun 15 17:58:20 bolt postfix/smtpd[10836]: NOQUEUE: reject: RCPT from static-200-105-220-154.acelerate.net[200.105.220.154]: 550 5.1.1 <advertising@*****.com>: Recipient address rejected: User unknown in virtual mailbox table; from=<[email protected]> to=<advertising@*****.com> proto=ESMTP helo=<static-200-105-220-154.acelerate.net> Jun 15 17:58:20 bolt postfix/smtpd[10836]: lost connection after DATA (0 bytes) from static-200-105-220-154.acelerate.net[200.105.220.154] Jun 15 17:58:20 bolt postfix/smtpd[10836]: disconnect from static-200-105-220-154.acelerate.net[200.105.220.154] Jun 15 17:58:29 bolt postfix/smtpd[10834]: connect from unknown[62.176.172.226] Jun 15 17:58:32 bolt postfix/smtpd[10834]: 386791241F9: client=unknown[62.176.172.226] Jun 15 17:58:34 bolt postfix/cleanup[10975]: 386791241F9: message-id=<[email protected]> Jun 15 17:58:34 bolt postfix/qmgr[10712]: 386791241F9: from=<[email protected]>, size=867, nrcpt=1 (queue active) Jun 15 17:58:35 bolt postfix/smtpd[10834]: disconnect from unknown[62.176.172.226] Jun 15 17:58:35 bolt amavis[11084]: (11084-17) Blocked SPAM, [62.176.172.226] [62.176.172.226] <[email protected]> -> <*****@*****>, Message-ID: <[email protected]>, mail_id: XczovKoMBYNr, Hits: 18.471, size: 867, 833 ms Jun 15 17:58:35 bolt postfix/smtp[10732]: 386791241F9: to=<*****@*****>, relay=127.0.0.1[127.0.0.1]:10024, delay=3.5, delays=2.7/0/0/0.83, dsn=2.7.0, status=sent (250 2.7.0 Ok, discarded, id=11084-17 - SPAM) Jun 15 17:58:35 bolt postfix/qmgr[10712]: 386791241F9: removed Jun 15 17:58:43 bolt postfix/smtpd[10836]: warning: 178.121.154.194: address not listed for hostname mm-194-154-121-178.dynamic.pppoe.mgts.by Jun 15 17:58:43 bolt postfix/smtpd[10836]: connect from unknown[178.121.154.194] Jun 15 17:58:45 bolt postfix/smtpd[10727]: connect from unknown[180.134.223.86] EDIT #2 Got some more info from the logs, this is a send request: mail.info.1:Jun 15 16:41:57 bolt amavis[5399]: (05399-06) Passed CLEAN, [110.139.48.64] [110.139.48.64] <paul@*****.se> -> <[email protected]>, Message-ID: <CHILKAT-MID-7c54ebcf-5501-de9b-f0b1-4f0234290d8d@HP-IRISH>, mail_id: 35l56Ramx6Nc, Hits: -2.941, size: 3329, queued_as: 2485770086, 136 ms mail.info.1:Jun 15 16:41:57 bolt postfix/smtp[4743]: 375C570082: to=<[email protected]>, relay=127.0.0.1[127.0.0.1]:10024, delay=4.8, delays=4.7/0/0/0.14, dsn=2.0.0, status=sent (250 2.0.0 Ok, id=05399-06, from MTA([127.0.0.1]:10025): 250 2.0.0 Ok: queued as 2485770086) Which apparently got thrue. Any ideas how to restrict this?

  Read the article

• NTPD issue - syncs then slowly loses ground

  - by ethrbunny

  RHEL 5 workstation. Has been running smoothly for years. I did a 'pup' recently and followed with a nice, cleansing reboot. Afterwards the system had some startup issues: namely MySQL refused to start. It just went "...." for 5-10 minutes before I did another boot and skipped that step (using 'interactive'). This was the only service that didn't wan't to start normally. So now that the system is booted I've found that it doesn't want to stay in sync with the NTP master and after 48 hours is refusing any SSH other than root. NTPD: this service starts normally and gets a lock on 4 servers. Almost immediately it starts to lose ground and now (after 3 days) is almost 40 hours behind. If I stop/start the service it gets the lock, resets the system clock and starts losing ground again. The 'hwclock' is set properly and maintains its time. Login: when I (re)start the ntp server I am able to login normally. I assume this problem is due to losing sync with LDAP. This appears to be verified by LDAP errors in /var/log/messages. Suggestions on where to look? ADDENDA: Tried deleting the 'drift' file. After a bit it gets recreated with 0.000. from /var/log/messages: Jan 17 06:54:01 aeolus ntpdate[5084]: step time server 129.95.96.10 offset 30.139216 sec Jan 17 06:54:01 aeolus ntpd[5086]: ntpd [email protected] Tue Oct 25 12:54:17 UTC 2011 (1) Jan 17 06:54:01 aeolus ntpd[5087]: precision = 1.000 usec Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, 0.0.0.0#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface wildcard, ::#123 Disabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, ::1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, fe80::213:72ff:fe20:4080#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface lo, 127.0.0.1#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: Listening on interface eth0, 10.127.24.81#123 Enabled Jan 17 06:54:01 aeolus ntpd[5087]: kernel time sync status 0040 Jan 17 06:54:02 aeolus ntpd[5087]: frequency initialized 0.000 PPM from /var/lib/ntp/drift Jan 17 06:54:02 aeolus ntpd[5087]: system event 'event_restart' (0x01) status 'sync_alarm, sync_unspec, 1 event, event_unspec' (0xc010) You can see the 30 second offset. This was after about one minute of operation.

  Read the article

• How to use Hardware RAID in Ubuntu Server

  - by user2071938

  I have an Adaptec RAID-Controller and created an RAID-1(Mirroring) succesfully. Now I have installed Ubuntu Server 12.04.3. When I type fdisk -l I get this output: bf@fileserver:~$ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/sda doesn't contain a valid partition table Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/sdb doesn't contain a valid partition table Disk /dev/sdc: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004c454 Device Boot Start End Blocks Id System /dev/sdc1 * 2048 499711 248832 83 Linux /dev/sdc2 501758 156301311 77899777 5 Extended /dev/sdc5 501760 156301311 77899776 8e Linux LVM Disk /dev/mapper/fileserver--vg-root: 75.6 GB, 75606523904 bytes 255 heads, 63 sectors/track, 9191 cylinders, total 147668992 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/fileserver--vg-root doesn't contain a valid partition table Disk /dev/mapper/ddf1_Data: 1000.1 GB, 1000065728512 bytes 255 heads, 63 sectors/track, 121584 cylinders, total 1953253376 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/mapper/ddf1_Data doesn't contain a valid partition table Disk /dev/mapper/fileserver--vg-swap_1: 4160 MB, 4160749568 bytes 255 heads, 63 sectors/track, 505 cylinders, total 8126464 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/fileserver--vg-swap_1 doesn't contain a valid partition table The 80 GB HDD is for the System The 1000.2 GB HDD should be for my data. But I'm a bit confused becauser there are listed two 1000.2 GB HDDs, due the Hardware RAID shoudln't there be only one HDD vissible to the OS? (I have two 1000.2 GB HDDs in an Raid-1 Array) dmraid gives me bf@fileserver:~$ sudo dmraid -r /dev/sdb: ddf1, ".ddf1_disks", GROUP, ok, 1953253376 sectors, data@ 0 /dev/sda: ddf1, ".ddf1_disks", GROUP, ok, 1953253376 sectors, data@ 0 so It seems to be ok? But how do I partitionate this disks and which one should I mount(sdb or sda?) Hope you can help me thx Florian

  Read the article

• XP OEM licensing when reinstalling Windows XP

  - by mindas

  My wife has managed to buy a Dell laptop she was using at her ex-employer that just went bust. The problem with it is the OS (Windows XP) which takes ages to boot and is generally disproportionally slow to the hardware of the machine. So my aim is to sacrifice a day and reinstall it. The problem I am slightly worried about is the licensing/registration/activation hell. Apart from the sticker (with WinXP license key), the laptop has no other paperwork proving this license is legitimate. I believe this was originally an OEM license. Unfortunately, I don't have the the installation CD. This computer also has MS Office installed (which I would like to retain) but it none of MS Office apps would launch due to some obscure error complaining about lack of free disk space (which computer has plenty of). I have absolutely no clue what kind of license this MS Office was. And because the company has gone into the administration, there is no way of getting this information nor installable media. I believe that by buying the hardware I have also acquired the software which I can use as I see fit. Correct me if I'm wrong. Above said, my question would be: What is the easiest way of reinstalling the XP? By easiest I mean avoiding spending my time to prove Microsoft support I've got the right to use the software (insert your computer says noooo joke here) but still being able to get to fresh virgin activated legal state of the XP. I used to work as a sysadmin many years ago so I am not afraid of any technical difficulties. The same question applies to MS Office. I imagine the process would consist of backing up all the data, pulling some bits from the registry and using that on the fresh install. As for reinstall I'd expect to use some sort of OEM Windows repair CD from Dell, right? Are those freely available? My other box (HP) has such a thing and it can't be used on any other brand. I'm sure somebody had to go through this licensing hell and could share his/her tips. Thanks in advance.

  Read the article

• DNS lookups failing somewhere between firewall and router

  - by TessellatingHeckler

  we have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch == Intel load balanced NICS in a server. It has been fine for years, suddenly DNS resolution stopped working on the server. No changes that I know of, so I can't work backwards from there. It was configured with the ISP's DNS servers, neither network device does DNS relaying. Wireshark shows the request go out but nothing comes back. The server networking stack seems OK though, because if we query an internal DNS server on a remote site, that works. I can logon to the Cisco, and DNS resolves OK from the command line. I can logon to the ZyWall, and DNS does not resolve from the command line. So the problem seems to be the firewall, patch cable or router, yes? On the router: interface Ethernet0 ip address aaa.bbb.ccc.ddd 255.255.255.ddd ip tcp adjust-mss 1450 hold-queue 100 out On the firewall: DNS server set to 8.8.8.8 (Google's), DNS traffic allowed LAN-WAN. What else should I look for? Update: Following This guide I've got traffic logging on the Cisco. I have also got access to a public DNS server which I can run tcpdump on to see things from the other side. And as per the below comments, I've tested with Dig and see that DNS over TCP works, and over UDP does not. Currently: DNS request from the server using TCP shows up in the firewall log, and in the Cisco log, and in tcpdump on the DNS server, the answer comes back, it works fine. DNS request from the server using UDP shows up in the firewall log, and in the Cisco log, does NOT show in tcpdump on the DNS server, times out. DNS request from the cisco (using UDP) does show up in tcpdump on the DNS server, answer received, works fine. Ping requests from the server and the cisco to the DNS server show up in tcpdump on the DNS server. DNS request from the server using UDP does show up on the firewall. Summary: TCP seems fine throughought. UDP works over the ADSL and to the Cisco, and it works from the server to the Cisco, but it doesn't cross the Cisco properly, it seems. I did see the Cisco showing as connected at 10Mb/full-duplex internally, and the firewall showing as 100Mb/full-duplex externally. I have forced the firewall to 10Mb and rebooted both devices. That seemed to help get UDP traffic (server-firewall-cisco) instead of (server-firewall), but did not fix it. Update: Sanitized Cisco config: version 12.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname cisco ! logging queue-limit 100 enable secret 5 {password} enable password 7 {password} ! ip subnet-zero ip domain name example.org ip name-server {nameserver_IP} ! ! ip audit notify log ip audit po max-events 100 no ftp-server write-enable ! interface Ethernet0 ip address {Inside_public_IP} 255.255.255.248 ip tcp adjust-mss 1460 hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface Dialer1 ip unnumbered Ethernet0 encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer persistent no cdp enable ppp chap hostname {ADSL_Username} ppp chap password 7 {ADSL_Password} ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 no ip http server no ip http secure-server ! access-list 23 permit {IP} dialer-list 1 protocol ip permit no cdp run snmp-server enable traps tty ! {con, vty} end

  Read the article

• OSX: Howto start VirtualBox VM on startup?

  - by snies

  The Question How do i start this Wiki VM at the startup of the OSX Server? I am running OSX Server 10.6.8 and VirtualBox 4.1.8 r75467 and a Debian Linux VM (called "wiki"). . What I tried so far Following this article: http://mikkel.hoegh.org/blog/2010/12/23/run-virtualbox-boot-mac-os-x/, i have wrote this plist and placed it in /Library/LaunchDaemons/bar.foo.WikiVirtualBox.plist: <plist version="1.0"> <dict> <key>Label</key> <string>bar.foo.WikiVirtualBox</string> <key>ProgramArguments</key> <array> <string>/usr/bin/VBoxHeadless</string> <string>-s</string> <string>wiki</string> </array> <key>RunAtLoad</key> <true></true> <key>UserName</key> <string>root</string> <key>WorkingDirectory</key> <string>/var/root</string> <key>StandardErrorPath</key> <string>/var/log/bar.foo.WikiVirtualBox.stderr.log</string> <key>StandardOutPath</key> <string>/var/log/bar.foo.WikiVirtualBox.stdout.log</string> </dict> </plist> and told launchd to start it: sudo launchctl load -w /Library/LaunchDaemons/bar.foo.WikiVirtualBox.plist . The Logfile But the VM doesn't start. A Look at tail -f /var/log/system.log shows: sudo[1909]: administrator : TTY=ttys000 ; PWD=/Users/administrator ; USER=root ; COMMAND=/bin/launchctl load -w /Library/LaunchDaemons/bar.foo.WikiVirtualBox.plist VBoxSVC[1914]: 3891612: (connectAndCheck) Untrusted apps are not allowed to connect to or launch Window Server before login. VBoxSVC[1914]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. com.apple.launchd[1] (bar.foo.WikiVirtualBox[1910]): Exited with exit code: 1 When i log into the server via ssh (so no login window opened) i can run: /usr/bin/VBoxHeadless -s wiki and it works. So i don't understand the error above.

  Read the article

• Deleting windows.edb and unchecking Indexing service lead to hard drive file records swapping

  - by linni

  I followed the instructions listed here:http://www.mydigitallife.info/2007/09/18/turn-off-and-disable-search-indexing-service-in-windows-xp/ to free up space on hard drive by deleting the windows.edb indexing file... I also stopped windows search service as mentioned in the comments following the article. In addition to unchecking the "Allow Indexing Service to index this disk for fast file searching" check box on the properties dialog for the C:\ drive, I did the same for two usb connected hard drives (J:\ and I:\ ). I'm not sure why I did that, thought it might shrink the windows.edb file so I wouldn't have to delete it (which sounded a bit risky in my ears at the time). The file of course didn't shrink so I ended up deleting it and freeing up over 3 GB of space, yeehaw. However, as soon as I had done this I could not access the usb connected hard drives anymore. The error I got was "I:\photos is not accessible" "The file or directory is corrupted and unreadable" when I tried to open the photos directory on I:\ Here is where I enter the twilight zone... I try disconnecting I:\ usb hard drive. But XP shows me that instead J:\ drive has disconnected and I:\ is still there. So I disconnect both drives and restart the computer. I then connect one drive, but it lists up the contents of the other drive on root level. I tried connecting the drives vice versa and the same thing happens. I try taking one of the hard drives to another computer and when I connect it there it lists up not its own contents but the contents of the other hard drive and gives the same error as above when I try and access any of the folders (even folders on the root that have the same name as folders on the other drive (e.g. J:\photos and I:\photos)??? And no, this is not a me mixing up my drive letters. Computer Manager - Disk management shows the same result as explorer: The drive size is correct (one is 500GB, the other is 640GB) but the drive name is of the opposite drive, as long as the contents. Also, one drive was full of data and the other almost empty but they incorrectly show their free space status of the other drive. Somehow the usb drives seem to have switched file tables, file records, boot records or something, extremely weird! Even weirder, if I try and create a text file or folder on this drive, it works fine, accessing them, saving, whatever, all good, but accessing any other data on the drive gives me an error. Does anyone have a clue what is going on and more importantly, how I can restore the correct folder listings to access my family photos ??? cheers, linni

  Read the article

• Starting/Stopping Custom PHP Chat Server Linux Service (CentOS)

  - by chad

  I have been trying all night to get this service working properly. I created this script from a template and am very new to bash coding. I wrote a fully functioning chat server in php which runs endlessly, but now want to make it a dedicated service. I want to do this so that it starts on server boot and boots back up if possible when there are any down-times with the server. The issue is that I need this thing to run in a detached screen so that I can monitor packet data or send server commands via SSH when need-be. The main problem that i'm having is that it needs to have its own PID when it starts so that I can stop/restart it when needed. I am the type who grinds on coding until I figure it out, but this is so new to me that it seems the learning curve here is very steep and frustrating. Below is my code if anybody can please help me with this one, i've gotten so tired I can't even concentrate any more :( #!/bin/sh # # chatserver # # chkconfig: 345 20 90 # description: chatServer Linux Service Daemon \ # for general server handling ### BEGIN INIT INFO # Provides: chatserver # Required-Start: $local_fs $network $named $syslog # Required-Stop: $local_fs $syslog # Default-Start: 3 4 5 # Default-Stop: 0 1 2 6 # Short-Description: This service maintains the chatServer # Description: chatServer Linux Service Daemon # for general server handling ### END INIT INFO # Source function library. . /etc/rc.d/init.d/functions exec="screen php -q /var/www/html/chatServer.php" prog="chatserver" config="/etc/sysconfig/$prog" pidfile="/var/run/chatserver.pid" [ -e /etc/sysconfig/$prog ] && . /etc/sysconfig/$prog lockfile=/var/lock/subsys/$prog start() { #$exec || exit 5 echo -n $"Starting $prog: " daemon $exec --name=$exec --pidfile=$pidfile retval=$? echo [ $retval -eq 0 ] && touch $lockfile return $retval } stop() { echo -n $"Stopping $prog: " killproc -p $pidfile rm -f $pidfile retval=$? echo [ $retval -eq 0 ] && rm -f $lockfile return $retval } restart() { stop start } reload() { restart } force_reload() { restart } rh_status() { # run checks to determine if the service is running or use generic status status $prog } rh_status_q() { rh_status >/dev/null 2>&1 } case "$1" in start) rh_status_q && exit 0 $1 ;; stop) rh_status_q || exit 0 $1 ;; restart) $1 ;; reload) rh_status_q || exit 7 $1 ;; force-reload) force_reload ;; status) rh_status ;; condrestart|try-restart) rh_status_q || exit 0 restart ;; *) echo $"Usage: $0 {start|stop|status|restart|condrestart|try-restart|reload|force-reload}" exit 2 esac exit $?

  Read the article

• Cisco VPNClient from Mac won't connect using iPhone Tethering

  - by Dan Short

  I just set up iPhone tethering from my Snow Leopard Macbook Pro to my iPhone 3GS with the Datapro 4GB plan from AT&T. When attempting to connect to my corporate VPN from the MacBook Pro with Cisco VPNClient 4.9.01 (0100) I get the following log information: Cisco Systems VPN Client Version 4.9.01 (0100) Copyright (C) 1998-2006 Cisco Systems, Inc. All Rights Reserved. Client Type(s): Mac OS X Running on: Darwin 10.6.0 Darwin Kernel Version 10.6.0: Wed Nov 10 18:13:17 PST 2010; root:xnu-1504.9.26~3/RELEASE_I386 i386 Config file directory: /etc/opt/cisco-vpnclient 1 13:02:50.791 02/22/2011 Sev=Info/4 CM/0x43100002 Begin connection process 2 13:02:50.791 02/22/2011 Sev=Warning/2 CVPND/0x83400011 Error -28 sending packet. Dst Addr: 0x0AD337FF, Src Addr: 0x0AD33702 (DRVIFACE:1158). 3 13:02:50.791 02/22/2011 Sev=Warning/2 CVPND/0x83400011 Error -28 sending packet. Dst Addr: 0x0A2581FF, Src Addr: 0x0A258102 (DRVIFACE:1158). 4 13:02:50.792 02/22/2011 Sev=Info/4 CM/0x43100004 Establish secure connection using Ethernet 5 13:02:50.792 02/22/2011 Sev=Info/4 CM/0x43100024 Attempt connection with server "209.235.253.115" 6 13:02:50.792 02/22/2011 Sev=Info/4 CVPND/0x43400019 Privilege Separation: binding to port: (500). 7 13:02:50.793 02/22/2011 Sev=Info/4 CVPND/0x43400019 Privilege Separation: binding to port: (4500). 8 13:02:50.793 02/22/2011 Sev=Info/6 IKE/0x4300003B Attempting to establish a connection with 209.235.253.115. 9 13:02:51.293 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 10 13:02:51.894 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 11 13:02:52.495 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 12 13:02:53.096 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 13 13:02:53.698 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 14 13:02:54.299 02/22/2011 Sev=Warning/2 CVPND/0x83400018 Output size mismatch. Actual: 0, Expected: 237. (DRVIFACE:1319) 15 13:02:54.299 02/22/2011 Sev=Info/4 IKE/0x43000075 Unable to acquire local IP address after 5 attempts (over 5 seconds), probably due to network socket failure. 16 13:02:54.299 02/22/2011 Sev=Warning/2 IKE/0xC300009A Failed to set up connection data 17 13:02:54.299 02/22/2011 Sev=Info/4 CM/0x4310001C Unable to contact server "209.235.253.115" 18 13:02:54.299 02/22/2011 Sev=Info/5 CM/0x43100025 Initializing CVPNDrv 19 13:02:54.300 02/22/2011 Sev=Info/4 CVPND/0x4340001F Privilege Separation: restoring MTU on primary interface. 20 13:02:54.300 02/22/2011 Sev=Info/4 IKE/0x43000001 IKE received signal to terminate VPN connection 21 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700008 IPSec driver successfully started 22 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 23 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x4370000D Key(s) deleted by Interface (192.168.0.171) 24 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 25 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 26 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x43700014 Deleted all keys 27 13:02:54.300 02/22/2011 Sev=Info/4 IPSEC/0x4370000A IPSec driver successfully stopped The key line is 15: 15 13:02:54.299 02/22/2011 Sev=Info/4 IKE/0x43000075 Unable to acquire local IP address after 5 attempts (over 5 seconds), probably due to network socket failure. I can't find anything online about this. I found a single entry for the error message in Google, and it was a swedish (or some other nordic language site) that didn't have an answer to the question. I've tried connecting through both USB and Bluetooth tethering to the iPhone, and they both return the exact same results. I don't have direct control over the firewall, but if changes are necessary to make it work, I may be able to get the powers-that-be to make adjustments. A solution that doesn't require reconfiguring the firewall would be far better of course... Does anyone know what I can do to make this behave? Thanks, Dan

  Read the article

• How to setup linux permissions the WWW folder?

  - by Xeoncross

  Updated Summery The /var/www directory is owned by root:root which means that no one can use it and it's entirely useless. Since we all want a web server that actually works (and no-one should be logging in as "root"), then we need to fix this. Only two entities need access. PHP/Perl/Ruby/Python all need access to the folders and files since they create many of them (i.e. /uploads/). These scripting languages should be running under nginx or apache (or even some other thing like FastCGI for PHP). The developers How do they get access? I know that someone, somewhere has done this before. With however-many billions of websites out there you would think that there would be more information on this topic. I know that 777 is full read/write/execute permission for owner/group/other. So this doesn't seem to be needed as it leaves random users full permissions. What permissions are need to be used on /var/www so that... Source control like git or svn Users in a group like "websites" (or even added to "www-data") Servers like apache or lighthttpd And PHP/Perl/Ruby can all read, create, and run files (and directories) there? If I'm correct, Ruby and PHP scripts are not "executed" directly - but passed to an interpreter. So there is no need for execute permission on files in /var/www...? Therefore, it seems like the correct permission would be chmod -R 1660 which would make all files shareable by these four entities all files non-executable by mistake block everyone else from the directory entirely set the permission mode to "sticky" for all future files Is this correct? Update: I just realized that files and directories might need different permissions - I was talking about files above so i'm not sure what the directory permissions would need to be. Update 2: The folder structure of /var/www changes drastically as one of the four entities above are always adding (and sometimes removing) folders and sub folders many levels deep. They also create and remove files that the other 3 entities might need read/write access to. Therefore, the permissions need to do the four things above for both files and directories. Since non of them should need execute permission (see question about ruby/php above) I would assume that rw-rw-r-- permission would be all that is needed and completely safe since these four entities are run by trusted personal (see #2) and all other users on the system only have read access. Update 3: This is for personal development machines and private company servers. No random "web customers" like a shared host. Update 4: This article by slicehost seems to be the best at explaining what is needed to setup permissions for your www folder. However, I'm not sure what user or group apache/nginx with PHP OR svn/git run as and how to change them. Update 5: I have (I think) finally found a way to get this all to work (answer below). However, I don't know if this is the correct and SECURE way to do this. Therefore I have started a bounty. The person that has the best method of securing and managing the www directory wins.

  Read the article

• How to connect to a Virtualbox guest from the host when network cable unplugged

  - by Greg K

  I'd like to work offline (I'm flying to the US twice this month), to do this I need access to a linux development server. When I work from home I boot a VirtualBox VM and that acts as my dev server for the day (providing Apache, PHP & MySQL to run my server side code). However, I'd like to work with my VM when I'm not connected to a network. I have my Ubuntu VM guest set up with a bridge connection so it can serve HTTP and provide SSH access from inside my local network. I've tried to manually configure my network settings on both Mac OSX (the host) and Ubuntu (the guest) but I can't even ping my own NIC address (127.0.0.1 can, 192.168.21.x I can't) in OS X when I unplug the cable. Manual network settings: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx inet 192.168.21.5 netmask 0xffffff00 broadcast 192.168.21.255 media: autoselect (100baseTX <full-duplex,flow-control>) status: active I can ping localhost fine, as well as my VM (.20) and SSH too. $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes 64 bytes from 192.168.21.5: icmp_seq=0 ttl=64 time=0.085 ms 64 bytes from 192.168.21.5: icmp_seq=1 ttl=64 time=0.102 ms 64 bytes from 192.168.21.5: icmp_seq=2 ttl=64 time=0.100 ms 64 bytes from 192.168.21.5: icmp_seq=3 ttl=64 time=0.094 ms $ ping 192.168.21.20 PING 192.168.21.20 (192.168.21.20): 56 data bytes 64 bytes from 192.168.21.20: icmp_seq=0 ttl=64 time=0.910 ms 64 bytes from 192.168.21.20: icmp_seq=1 ttl=64 time=1.181 ms 64 bytes from 192.168.21.20: icmp_seq=2 ttl=64 time=1.159 ms 64 bytes from 192.168.21.20: icmp_seq=3 ttl=64 time=1.320 ms Network cable unplugged: $ ifconfig en0 en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:xx:xx:xx:xx:xx media: autoselect status: inactive $ ping 192.168.21.5 PING 192.168.21.5 (192.168.21.5): 56 data bytes ping: sendto: No route to host ping: sendto: No route to host Request timeout for icmp_seq 0 ping: sendto: No route to host Request timeout for icmp_seq 1 Does OS X disable the NIC when the network cable is unplugged? Any way to stop it doing this?

  Read the article

• SSD Fresh Does Not Start

  - by Jim Fell

  I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fress from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried shutting down the Spybot Resident and disabling the firewall and virus scanner with no luck. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

  Read the article

< Previous Page | 449 450 451 452 453 454 455 456 457 458 459 460  | Next Page >